ARM: cpu topology: Add debugfs interface for cpu_power
[cmplus.git] / arch / arm / mach-omap2 / board-overo.c
blob175e1ab2b04d7225a0a13485e12e239e9692030d
1 /*
2 * board-overo.c (Gumstix Overo)
4 * Initial code: Steve Sakoman <steve@sakoman.com>
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License
8 * version 2 as published by the Free Software Foundation.
10 * This program is distributed in the hope that it will be useful, but
11 * WITHOUT ANY WARRANTY; without even the implied warranty of
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
13 * General Public License for more details.
15 * You should have received a copy of the GNU General Public License
16 * along with this program; if not, write to the Free Software
17 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
18 * 02110-1301 USA
22 #include <linux/clk.h>
23 #include <linux/delay.h>
24 #include <linux/err.h>
25 #include <linux/init.h>
26 #include <linux/io.h>
27 #include <linux/gpio.h>
28 #include <linux/kernel.h>
29 #include <linux/platform_device.h>
30 #include <linux/i2c/twl.h>
31 #include <linux/regulator/machine.h>
32 #include <linux/regulator/fixed.h>
33 #include <linux/spi/spi.h>
35 #include <linux/mtd/mtd.h>
36 #include <linux/mtd/nand.h>
37 #include <linux/mtd/partitions.h>
38 #include <linux/mmc/host.h>
40 #include <asm/mach-types.h>
41 #include <asm/mach/arch.h>
42 #include <asm/mach/flash.h>
43 #include <asm/mach/map.h>
45 #include <plat/board.h>
46 #include <plat/common.h>
47 #include <video/omapdss.h>
48 #include <video/omap-panel-generic-dpi.h>
49 #include <plat/gpmc.h>
50 #include <mach/hardware.h>
51 #include <plat/nand.h>
52 #include <plat/mcspi.h>
53 #include <plat/mux.h>
54 #include <plat/usb.h>
56 #include "mux.h"
57 #include "sdram-micron-mt46h32m32lf-6.h"
58 #include "hsmmc.h"
59 #include "common-board-devices.h"
61 #define OVERO_GPIO_BT_XGATE 15
62 #define OVERO_GPIO_W2W_NRESET 16
63 #define OVERO_GPIO_PENDOWN 114
64 #define OVERO_GPIO_BT_NRESET 164
65 #define OVERO_GPIO_USBH_CPEN 168
66 #define OVERO_GPIO_USBH_NRESET 183
68 #define OVERO_SMSC911X_CS 5
69 #define OVERO_SMSC911X_GPIO 176
70 #define OVERO_SMSC911X2_CS 4
71 #define OVERO_SMSC911X2_GPIO 65
73 #if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
74 defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
76 /* fixed regulator for ads7846 */
77 static struct regulator_consumer_supply ads7846_supply =
78 REGULATOR_SUPPLY("vcc", "spi1.0");
80 static struct regulator_init_data vads7846_regulator = {
81 .constraints = {
82 .valid_ops_mask = REGULATOR_CHANGE_STATUS,
84 .num_consumer_supplies = 1,
85 .consumer_supplies = &ads7846_supply,
88 static struct fixed_voltage_config vads7846 = {
89 .supply_name = "vads7846",
90 .microvolts = 3300000, /* 3.3V */
91 .gpio = -EINVAL,
92 .startup_delay = 0,
93 .init_data = &vads7846_regulator,
96 static struct platform_device vads7846_device = {
97 .name = "reg-fixed-voltage",
98 .id = 1,
99 .dev = {
100 .platform_data = &vads7846,
104 static void __init overo_ads7846_init(void)
106 omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL);
107 platform_device_register(&vads7846_device);
110 #else
111 static inline void __init overo_ads7846_init(void) { return; }
112 #endif
114 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
116 #include <linux/smsc911x.h>
117 #include <plat/gpmc-smsc911x.h>
119 static struct omap_smsc911x_platform_data smsc911x_cfg = {
120 .id = 0,
121 .cs = OVERO_SMSC911X_CS,
122 .gpio_irq = OVERO_SMSC911X_GPIO,
123 .gpio_reset = -EINVAL,
124 .flags = SMSC911X_USE_32BIT,
127 static struct omap_smsc911x_platform_data smsc911x2_cfg = {
128 .id = 1,
129 .cs = OVERO_SMSC911X2_CS,
130 .gpio_irq = OVERO_SMSC911X2_GPIO,
131 .gpio_reset = -EINVAL,
132 .flags = SMSC911X_USE_32BIT,
135 static void __init overo_init_smsc911x(void)
137 gpmc_smsc911x_init(&smsc911x_cfg);
138 gpmc_smsc911x_init(&smsc911x2_cfg);
141 #else
142 static inline void __init overo_init_smsc911x(void) { return; }
143 #endif
145 /* DSS */
146 static int lcd_enabled;
147 static int dvi_enabled;
149 #define OVERO_GPIO_LCD_EN 144
150 #define OVERO_GPIO_LCD_BL 145
152 static struct gpio overo_dss_gpios[] __initdata = {
153 { OVERO_GPIO_LCD_EN, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_EN" },
154 { OVERO_GPIO_LCD_BL, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_BL" },
157 static void __init overo_display_init(void)
159 if (gpio_request_array(overo_dss_gpios, ARRAY_SIZE(overo_dss_gpios))) {
160 printk(KERN_ERR "could not obtain DSS control GPIOs\n");
161 return;
164 gpio_export(OVERO_GPIO_LCD_EN, 0);
165 gpio_export(OVERO_GPIO_LCD_BL, 0);
168 static int overo_panel_enable_dvi(struct omap_dss_device *dssdev)
170 if (lcd_enabled) {
171 printk(KERN_ERR "cannot enable DVI, LCD is enabled\n");
172 return -EINVAL;
174 dvi_enabled = 1;
176 return 0;
179 static void overo_panel_disable_dvi(struct omap_dss_device *dssdev)
181 dvi_enabled = 0;
184 static struct panel_generic_dpi_data dvi_panel = {
185 .name = "generic",
186 .platform_enable = overo_panel_enable_dvi,
187 .platform_disable = overo_panel_disable_dvi,
190 static struct omap_dss_device overo_dvi_device = {
191 .name = "dvi",
192 .type = OMAP_DISPLAY_TYPE_DPI,
193 .driver_name = "generic_dpi_panel",
194 .data = &dvi_panel,
195 .phy.dpi.data_lines = 24,
198 static struct omap_dss_device overo_tv_device = {
199 .name = "tv",
200 .driver_name = "venc",
201 .type = OMAP_DISPLAY_TYPE_VENC,
202 .phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
205 static int overo_panel_enable_lcd(struct omap_dss_device *dssdev)
207 if (dvi_enabled) {
208 printk(KERN_ERR "cannot enable LCD, DVI is enabled\n");
209 return -EINVAL;
212 gpio_set_value(OVERO_GPIO_LCD_EN, 1);
213 gpio_set_value(OVERO_GPIO_LCD_BL, 1);
214 lcd_enabled = 1;
215 return 0;
218 static void overo_panel_disable_lcd(struct omap_dss_device *dssdev)
220 gpio_set_value(OVERO_GPIO_LCD_EN, 0);
221 gpio_set_value(OVERO_GPIO_LCD_BL, 0);
222 lcd_enabled = 0;
225 static struct panel_generic_dpi_data lcd43_panel = {
226 .name = "samsung_lte430wq_f0c",
227 .platform_enable = overo_panel_enable_lcd,
228 .platform_disable = overo_panel_disable_lcd,
231 static struct omap_dss_device overo_lcd43_device = {
232 .name = "lcd43",
233 .type = OMAP_DISPLAY_TYPE_DPI,
234 .driver_name = "generic_dpi_panel",
235 .data = &lcd43_panel,
236 .phy.dpi.data_lines = 24,
239 #if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \
240 defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE)
241 static struct omap_dss_device overo_lcd35_device = {
242 .type = OMAP_DISPLAY_TYPE_DPI,
243 .name = "lcd35",
244 .driver_name = "lgphilips_lb035q02_panel",
245 .phy.dpi.data_lines = 24,
246 .platform_enable = overo_panel_enable_lcd,
247 .platform_disable = overo_panel_disable_lcd,
249 #endif
251 static struct omap_dss_device *overo_dss_devices[] = {
252 &overo_dvi_device,
253 &overo_tv_device,
254 #if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \
255 defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE)
256 &overo_lcd35_device,
257 #endif
258 &overo_lcd43_device,
261 static struct omap_dss_board_info overo_dss_data = {
262 .num_devices = ARRAY_SIZE(overo_dss_devices),
263 .devices = overo_dss_devices,
264 .default_device = &overo_dvi_device,
267 static struct regulator_consumer_supply overo_vdda_dac_supply =
268 REGULATOR_SUPPLY("vdda_dac", "omapdss_venc");
270 static struct regulator_consumer_supply overo_vdds_dsi_supply[] = {
271 REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
272 REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"),
275 static struct mtd_partition overo_nand_partitions[] = {
277 .name = "xloader",
278 .offset = 0, /* Offset = 0x00000 */
279 .size = 4 * NAND_BLOCK_SIZE,
280 .mask_flags = MTD_WRITEABLE
283 .name = "uboot",
284 .offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
285 .size = 14 * NAND_BLOCK_SIZE,
288 .name = "uboot environment",
289 .offset = MTDPART_OFS_APPEND, /* Offset = 0x240000 */
290 .size = 2 * NAND_BLOCK_SIZE,
293 .name = "linux",
294 .offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
295 .size = 32 * NAND_BLOCK_SIZE,
298 .name = "rootfs",
299 .offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
300 .size = MTDPART_SIZ_FULL,
304 static struct omap2_hsmmc_info mmc[] = {
306 .mmc = 1,
307 .caps = MMC_CAP_4_BIT_DATA,
308 .gpio_cd = -EINVAL,
309 .gpio_wp = -EINVAL,
312 .mmc = 2,
313 .caps = MMC_CAP_4_BIT_DATA,
314 .gpio_cd = -EINVAL,
315 .gpio_wp = -EINVAL,
316 .transceiver = true,
317 .ocr_mask = 0x00100000, /* 3.3V */
319 {} /* Terminator */
322 static struct regulator_consumer_supply overo_vmmc1_supply = {
323 .supply = "vmmc",
326 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
327 #include <linux/leds.h>
329 static struct gpio_led gpio_leds[] = {
331 .name = "overo:red:gpio21",
332 .default_trigger = "heartbeat",
333 .gpio = 21,
334 .active_low = true,
337 .name = "overo:blue:gpio22",
338 .default_trigger = "none",
339 .gpio = 22,
340 .active_low = true,
343 .name = "overo:blue:COM",
344 .default_trigger = "mmc0",
345 .gpio = -EINVAL, /* gets replaced */
346 .active_low = true,
350 static struct gpio_led_platform_data gpio_leds_pdata = {
351 .leds = gpio_leds,
352 .num_leds = ARRAY_SIZE(gpio_leds),
355 static struct platform_device gpio_leds_device = {
356 .name = "leds-gpio",
357 .id = -1,
358 .dev = {
359 .platform_data = &gpio_leds_pdata,
363 static void __init overo_init_led(void)
365 platform_device_register(&gpio_leds_device);
368 #else
369 static inline void __init overo_init_led(void) { return; }
370 #endif
372 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
373 #include <linux/input.h>
374 #include <linux/gpio_keys.h>
376 static struct gpio_keys_button gpio_buttons[] = {
378 .code = BTN_0,
379 .gpio = 23,
380 .desc = "button0",
381 .wakeup = 1,
384 .code = BTN_1,
385 .gpio = 14,
386 .desc = "button1",
387 .wakeup = 1,
391 static struct gpio_keys_platform_data gpio_keys_pdata = {
392 .buttons = gpio_buttons,
393 .nbuttons = ARRAY_SIZE(gpio_buttons),
396 static struct platform_device gpio_keys_device = {
397 .name = "gpio-keys",
398 .id = -1,
399 .dev = {
400 .platform_data = &gpio_keys_pdata,
404 static void __init overo_init_keys(void)
406 platform_device_register(&gpio_keys_device);
409 #else
410 static inline void __init overo_init_keys(void) { return; }
411 #endif
413 static int overo_twl_gpio_setup(struct device *dev,
414 unsigned gpio, unsigned ngpio)
416 omap2_hsmmc_init(mmc);
418 overo_vmmc1_supply.dev = mmc[0].dev;
420 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
421 /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
422 gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
423 #endif
425 return 0;
428 static struct twl4030_gpio_platform_data overo_gpio_data = {
429 .gpio_base = OMAP_MAX_GPIO_LINES,
430 .irq_base = TWL4030_GPIO_IRQ_BASE,
431 .irq_end = TWL4030_GPIO_IRQ_END,
432 .use_leds = true,
433 .setup = overo_twl_gpio_setup,
436 static struct twl4030_usb_data overo_usb_data = {
437 .usb_mode = T2_USB_MODE_ULPI,
440 static struct regulator_init_data overo_vmmc1 = {
441 .constraints = {
442 .min_uV = 1850000,
443 .max_uV = 3150000,
444 .valid_modes_mask = REGULATOR_MODE_NORMAL
445 | REGULATOR_MODE_STANDBY,
446 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
447 | REGULATOR_CHANGE_MODE
448 | REGULATOR_CHANGE_STATUS,
450 .num_consumer_supplies = 1,
451 .consumer_supplies = &overo_vmmc1_supply,
454 /* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
455 static struct regulator_init_data overo_vdac = {
456 .constraints = {
457 .min_uV = 1800000,
458 .max_uV = 1800000,
459 .valid_modes_mask = REGULATOR_MODE_NORMAL
460 | REGULATOR_MODE_STANDBY,
461 .valid_ops_mask = REGULATOR_CHANGE_MODE
462 | REGULATOR_CHANGE_STATUS,
464 .num_consumer_supplies = 1,
465 .consumer_supplies = &overo_vdda_dac_supply,
468 /* VPLL2 for digital video outputs */
469 static struct regulator_init_data overo_vpll2 = {
470 .constraints = {
471 .name = "VDVI",
472 .min_uV = 1800000,
473 .max_uV = 1800000,
474 .valid_modes_mask = REGULATOR_MODE_NORMAL
475 | REGULATOR_MODE_STANDBY,
476 .valid_ops_mask = REGULATOR_CHANGE_MODE
477 | REGULATOR_CHANGE_STATUS,
479 .num_consumer_supplies = ARRAY_SIZE(overo_vdds_dsi_supply),
480 .consumer_supplies = overo_vdds_dsi_supply,
483 static struct twl4030_codec_audio_data overo_audio_data;
485 static struct twl4030_codec_data overo_codec_data = {
486 .audio_mclk = 26000000,
487 .audio = &overo_audio_data,
490 static struct twl4030_platform_data overo_twldata = {
491 .irq_base = TWL4030_IRQ_BASE,
492 .irq_end = TWL4030_IRQ_END,
493 .gpio = &overo_gpio_data,
494 .usb = &overo_usb_data,
495 .codec = &overo_codec_data,
496 .vmmc1 = &overo_vmmc1,
497 .vdac = &overo_vdac,
498 .vpll2 = &overo_vpll2,
501 static int __init overo_i2c_init(void)
503 omap3_pmic_init("tps65950", &overo_twldata);
504 /* i2c2 pins are used for gpio */
505 omap_register_i2c_bus(3, 400, NULL, 0);
506 return 0;
509 static struct spi_board_info overo_spi_board_info[] __initdata = {
510 #if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \
511 defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE)
513 .modalias = "lgphilips_lb035q02_panel-spi",
514 .bus_num = 1,
515 .chip_select = 1,
516 .max_speed_hz = 500000,
517 .mode = SPI_MODE_3,
519 #endif
522 static int __init overo_spi_init(void)
524 overo_ads7846_init();
525 spi_register_board_info(overo_spi_board_info,
526 ARRAY_SIZE(overo_spi_board_info));
527 return 0;
530 static void __init overo_init_early(void)
532 omap2_init_common_infrastructure();
533 omap2_init_common_devices(mt46h32m32lf6_sdrc_params,
534 mt46h32m32lf6_sdrc_params);
537 static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
538 .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
539 .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
540 .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
541 .phy_reset = true,
542 .reset_gpio_port[0] = -EINVAL,
543 .reset_gpio_port[1] = OVERO_GPIO_USBH_NRESET,
544 .reset_gpio_port[2] = -EINVAL
547 #ifdef CONFIG_OMAP_MUX
548 static struct omap_board_mux board_mux[] __initdata = {
549 { .reg_offset = OMAP_MUX_TERMINATOR },
551 #endif
553 static struct gpio overo_bt_gpios[] __initdata = {
554 { OVERO_GPIO_BT_XGATE, GPIOF_OUT_INIT_LOW, "lcd enable" },
555 { OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
558 static void __init overo_init(void)
560 int ret;
562 omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
563 overo_i2c_init();
564 omap_display_init(&overo_dss_data);
565 omap_serial_init();
566 omap_nand_flash_init(0, overo_nand_partitions,
567 ARRAY_SIZE(overo_nand_partitions));
568 usb_musb_init(NULL);
569 usbhs_init(&usbhs_bdata);
570 overo_spi_init();
571 overo_ads7846_init();
572 overo_init_smsc911x();
573 overo_display_init();
574 overo_init_led();
575 overo_init_keys();
577 /* Ensure SDRC pins are mux'd for self-refresh */
578 omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
579 omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
581 ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH,
582 "OVERO_GPIO_W2W_NRESET");
583 if (ret == 0) {
584 gpio_export(OVERO_GPIO_W2W_NRESET, 0);
585 gpio_set_value(OVERO_GPIO_W2W_NRESET, 0);
586 udelay(10);
587 gpio_set_value(OVERO_GPIO_W2W_NRESET, 1);
588 } else {
589 printk(KERN_ERR "could not obtain gpio for "
590 "OVERO_GPIO_W2W_NRESET\n");
593 ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios));
594 if (ret) {
595 pr_err("%s: could not obtain BT gpios\n", __func__);
596 } else {
597 gpio_export(OVERO_GPIO_BT_XGATE, 0);
598 gpio_export(OVERO_GPIO_BT_NRESET, 0);
599 gpio_set_value(OVERO_GPIO_BT_NRESET, 0);
600 mdelay(6);
601 gpio_set_value(OVERO_GPIO_BT_NRESET, 1);
604 ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH,
605 "OVERO_GPIO_USBH_CPEN");
606 if (ret == 0)
607 gpio_export(OVERO_GPIO_USBH_CPEN, 0);
608 else
609 printk(KERN_ERR "could not obtain gpio for "
610 "OVERO_GPIO_USBH_CPEN\n");
613 MACHINE_START(OVERO, "Gumstix Overo")
614 .boot_params = 0x80000100,
615 .reserve = omap_reserve,
616 .map_io = omap3_map_io,
617 .init_early = overo_init_early,
618 .init_irq = omap_init_irq,
619 .init_machine = overo_init,
620 .timer = &omap_timer,
621 MACHINE_END