soc/intel: Remove blank lines before '}' and after '{'

[coreboot2.git] / src / mainboard / hp / snb_ivb_desktops / devicetree.cb

## SPDX-License-Identifier: GPL-2.0-only

chip northbridge/intel/sandybridge
        register "gfx.use_spread_spectrum_clock" = "0"
        register "gpu_dp_b_hotplug" = "0"
        register "gpu_dp_c_hotplug" = "0"
        register "gpu_dp_d_hotplug" = "0"
        # BTX mainboard: Reversed mapping
        register "spd_addresses" = "{0x53, 0x52, 0x51, 0x50}"

        device domain 0 on
                device ref host_bridge on  end
                device ref peg10 on  end
                device ref igd on  end
                device ref peg60 off end

                chip southbridge/intel/bd82x6x # Intel Series 7 PCH
                        register "docking_supported" = "0"
                        register "gen1_dec" = "0x00fc0601"
                        register "gen2_dec" = "0x00fc0801"
                        register "pcie_hotplug_map" = "{ 0, 0, 0, 0, 0, 0, 0, 0 }"
                        register "pcie_port_coalesce" = "true"
                        register "sata_interface_speed_support" = "0x3"
                        register "spi_lvscc" = "0x2005"
                        register "spi_uvscc" = "0x2005"

                        device ref mei1 on  end
                        device ref mei2 off end
                        device ref me_ide_r off end
                        device ref me_kt on  end
                        device ref gbe on  end
                        device ref ehci2 on  end
                        device ref hda on  end
                        device ref pcie_rp1 on  end
                        device ref pcie_rp2 off end
                        device ref pcie_rp3 off end
                        device ref pcie_rp4 off end
                        device ref pcie_rp5 on  end
                        device ref pcie_rp6 off end
                        device ref pcie_rp7 off end
                        device ref pcie_rp8 off end
                        device ref ehci1 on  end
                        device ref pci_bridge on  end
                        device ref lpc on
                                chip superio/common
                                        device pnp 2e.ff on # passes SIO base addr to SSDT gen
                                                chip superio/nuvoton/npcd378
                                                        device pnp 2e.0 off end         # Floppy
                                                        device pnp 2e.1 on              # Parallel port
                                                                # global

                                                                # serialice: Vendor writes:
                                                                irq 0x14 = 0x9c
                                                                irq 0x1c = 0xa8
                                                                irq 0x1d = 0x08
                                                                irq 0x22 = 0x3f
                                                                irq 0x1a = 0xb0
                                                                # dumped from superiotool:
                                                                irq 0x1b = 0x1e
                                                                irq 0x27 = 0x08
                                                                irq 0x2a = 0x20
                                                                irq 0x2d = 0x01
                                                                # parallel port
                                                                io 0x60 = 0x378
                                                                irq 0x70 = 0x07
                                                                drq 0x74 = 0x01
                                                        end
                                                        device pnp 2e.2 off             # COM1
                                                                io 0x60 = 0x2f8
                                                                irq 0x70 = 3
                                                        end
                                                        device pnp 2e.3 on              # COM2, IR
                                                                io 0x60 = 0x3f8
                                                                irq 0x70 = 4
                                                        end
                                                        device pnp 2e.4 on              # LED control
                                                                io 0x60 = 0x600
                                                                # IOBASE[0h] = bit0 LED red / green
                                                                # IOBASE[0h] = bit1-4 LED PWM duty cycle
                                                                # IOBASE[1h] = bit6 SWCC

                                                                io 0x62 = 0x610
                                                                # IOBASE [0h] = GPES
                                                                # IOBASE [1h] = GPEE
                                                                # IOBASE [4h:7h] = 32bit upcounter at 1Mhz
                                                                # IOBASE [8h:bh] = GPS
                                                                # IOBASE [ch:fh] = GPE
                                                        end
                                                        device pnp 2e.5 on              # Mouse
                                                                irq 0x70 = 0xc
                                                        end
                                                        device pnp 2e.6 on              # Keyboard
                                                                io 0x60 = 0x0060
                                                                io 0x62 = 0x0064
                                                                irq 0x70 = 0x01
                                                                # serialice: Vendor writes:
                                                                drq 0xf0 = 0x40
                                                        end
                                                        device pnp 2e.7 on              #  WDT ?
                                                                io 0x60 = 0x620
                                                        end
                                                        device pnp 2e.8 on              # HWM
                                                                io 0x60 = 0x800
                                                                # IOBASE[0h:feh] HWM page
                                                                # IOBASE[ffh] bit0-bit3 page selector

                                                                drq 0xf0 = 0x20
                                                                drq 0xf1 = 0x01
                                                                drq 0xf2 = 0x40
                                                                drq 0xf3 = 0x01

                                                                drq 0xf4 = 0x66
                                                                drq 0xf5 = 0x67
                                                                drq 0xf6 = 0x66
                                                                drq 0xf7 = 0x01
                                                        end
                                                        device pnp 2e.f on              # GPIO OD ?
                                                                drq 0xf1 = 0x97
                                                                drq 0xf2 = 0x01
                                                                drq 0xf5 = 0x08
                                                                drq 0xfe = 0x80
                                                        end
                                                        device pnp 2e.15 on             # BUS ?
                                                                io 0x60 = 0x0680
                                                                io 0x62 = 0x0690
                                                        end
                                                        device pnp 2e.1c on             # Suspend Control ?
                                                                io 0x60 = 0x640
                                                                # writing to IOBASE[5h]
                                                                #  0x0: Power off
                                                                #  0x9: Power off and bricked until CMOS battery removed
                                                        end
                                                        device pnp 2e.1e on             # GPIO ?
                                                                io 0x60 = 0x660
                                                                drq 0xf4 = 0x01
                                                                # skip the following, as it
                                                                # looks like remapped registers
                                                                #drq 0xf5 = 0x06
                                                                #drq 0xf6 = 0x60
                                                                #drq 0xfe = 0x03
                                                        end
                                                end
                                        end
                                end
                                chip drivers/pc80/tpm
                                        device pnp 4e.0 on end          # TPM module
                                end
                        end
                        device ref sata1 on  end
                        device ref smbus on  end
                        device ref sata2 off end
                        device ref thermal off end
                end
        end
end