acpi_pad: build only on X86
[linux-2.6/linux-acpi-2.6.git] / sound / oss / sb_common.c
blob77d0e5efda76a9bcd2138f878b2e0a442f137137
1 /*
2 * sound/oss/sb_common.c
4 * Common routines for Sound Blaster compatible cards.
7 * Copyright (C) by Hannu Savolainen 1993-1997
9 * OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL)
10 * Version 2 (June 1991). See the "COPYING" file distributed with this software
11 * for more info.
14 * Daniel J. Rodriksson: Modified sbintr to handle 8 and 16 bit interrupts
15 * for full duplex support ( only sb16 by now )
16 * Rolf Fokkens: Added (BETA?) support for ES1887 chips.
17 * (fokkensr@vertis.nl) Which means: You can adjust the recording levels.
19 * 2000/01/18 - separated sb_card and sb_common -
20 * Jeff Garzik <jgarzik@pobox.com>
22 * 2000/09/18 - got rid of attach_uart401
23 * Arnaldo Carvalho de Melo <acme@conectiva.com.br>
25 * 2001/01/26 - replaced CLI/STI with spinlocks
26 * Chris Rankin <rankinc@zipworld.com.au>
29 #include <linux/init.h>
30 #include <linux/interrupt.h>
31 #include <linux/module.h>
32 #include <linux/delay.h>
33 #include <linux/spinlock.h>
35 #include "sound_config.h"
36 #include "sound_firmware.h"
38 #include "mpu401.h"
40 #include "sb_mixer.h"
41 #include "sb.h"
42 #include "sb_ess.h"
45 * global module flag
48 int sb_be_quiet;
50 static sb_devc *detected_devc; /* For communication from probe to init */
51 static sb_devc *last_devc; /* For MPU401 initialization */
53 static unsigned char jazz_irq_bits[] = {
54 0, 0, 2, 3, 0, 1, 0, 4, 0, 2, 5, 0, 0, 0, 0, 6
57 static unsigned char jazz_dma_bits[] = {
58 0, 1, 0, 2, 0, 3, 0, 4
61 void *smw_free;
64 * Jazz16 chipset specific control variables
67 static int jazz16_base; /* Not detected */
68 static unsigned char jazz16_bits; /* I/O relocation bits */
69 static DEFINE_SPINLOCK(jazz16_lock);
72 * Logitech Soundman Wave specific initialization code
75 #ifdef SMW_MIDI0001_INCLUDED
76 #include "smw-midi0001.h"
77 #else
78 static unsigned char *smw_ucode;
79 static int smw_ucodeLen;
81 #endif
83 static sb_devc *last_sb; /* Last sb loaded */
85 int sb_dsp_command(sb_devc * devc, unsigned char val)
87 int i;
88 unsigned long limit;
90 limit = jiffies + HZ / 10; /* Timeout */
93 * Note! the i<500000 is an emergency exit. The sb_dsp_command() is sometimes
94 * called while interrupts are disabled. This means that the timer is
95 * disabled also. However the timeout situation is a abnormal condition.
96 * Normally the DSP should be ready to accept commands after just couple of
97 * loops.
100 for (i = 0; i < 500000 && (limit-jiffies)>0; i++)
102 if ((inb(DSP_STATUS) & 0x80) == 0)
104 outb((val), DSP_COMMAND);
105 return 1;
108 printk(KERN_WARNING "Sound Blaster: DSP command(%x) timeout.\n", val);
109 return 0;
112 int sb_dsp_get_byte(sb_devc * devc)
114 int i;
116 for (i = 1000; i; i--)
118 if (inb(DSP_DATA_AVAIL) & 0x80)
119 return inb(DSP_READ);
121 return 0xffff;
124 static void sb_intr (sb_devc *devc)
126 int status;
127 unsigned char src = 0xff;
129 if (devc->model == MDL_SB16)
131 src = sb_getmixer(devc, IRQ_STAT); /* Interrupt source register */
133 if (src & 4) /* MPU401 interrupt */
134 if(devc->midi_irq_cookie)
135 uart401intr(devc->irq, devc->midi_irq_cookie);
137 if (!(src & 3))
138 return; /* Not a DSP interrupt */
140 if (devc->intr_active && (!devc->fullduplex || (src & 0x01)))
142 switch (devc->irq_mode)
144 case IMODE_OUTPUT:
145 DMAbuf_outputintr(devc->dev, 1);
146 break;
148 case IMODE_INPUT:
149 DMAbuf_inputintr(devc->dev);
150 break;
152 case IMODE_INIT:
153 break;
155 case IMODE_MIDI:
156 sb_midi_interrupt(devc);
157 break;
159 default:
160 /* printk(KERN_WARN "Sound Blaster: Unexpected interrupt\n"); */
164 else if (devc->intr_active_16 && (src & 0x02))
166 switch (devc->irq_mode_16)
168 case IMODE_OUTPUT:
169 DMAbuf_outputintr(devc->dev, 1);
170 break;
172 case IMODE_INPUT:
173 DMAbuf_inputintr(devc->dev);
174 break;
176 case IMODE_INIT:
177 break;
179 default:
180 /* printk(KERN_WARN "Sound Blaster: Unexpected interrupt\n"); */
185 * Acknowledge interrupts
188 if (src & 0x01)
189 status = inb(DSP_DATA_AVAIL);
191 if (devc->model == MDL_SB16 && src & 0x02)
192 status = inb(DSP_DATA_AVL16);
195 static void pci_intr(sb_devc *devc)
197 int src = inb(devc->pcibase+0x1A);
198 src&=3;
199 if(src)
200 sb_intr(devc);
203 static irqreturn_t sbintr(int irq, void *dev_id)
205 sb_devc *devc = dev_id;
207 devc->irq_ok = 1;
209 switch (devc->model) {
210 case MDL_ESSPCI:
211 pci_intr (devc);
212 break;
214 case MDL_ESS:
215 ess_intr (devc);
216 break;
217 default:
218 sb_intr (devc);
219 break;
221 return IRQ_HANDLED;
224 int sb_dsp_reset(sb_devc * devc)
226 int loopc;
228 DEB(printk("Entered sb_dsp_reset()\n"));
230 if (devc->model == MDL_ESS) return ess_dsp_reset (devc);
232 /* This is only for non-ESS chips */
234 outb(1, DSP_RESET);
236 udelay(10);
237 outb(0, DSP_RESET);
238 udelay(30);
240 for (loopc = 0; loopc < 1000 && !(inb(DSP_DATA_AVAIL) & 0x80); loopc++);
242 if (inb(DSP_READ) != 0xAA)
244 DDB(printk("sb: No response to RESET\n"));
245 return 0; /* Sorry */
248 DEB(printk("sb_dsp_reset() OK\n"));
250 return 1;
253 static void dsp_get_vers(sb_devc * devc)
255 int i;
257 unsigned long flags;
259 DDB(printk("Entered dsp_get_vers()\n"));
260 spin_lock_irqsave(&devc->lock, flags);
261 devc->major = devc->minor = 0;
262 sb_dsp_command(devc, 0xe1); /* Get version */
264 for (i = 100000; i; i--)
266 if (inb(DSP_DATA_AVAIL) & 0x80)
268 if (devc->major == 0)
269 devc->major = inb(DSP_READ);
270 else
272 devc->minor = inb(DSP_READ);
273 break;
277 spin_unlock_irqrestore(&devc->lock, flags);
278 DDB(printk("DSP version %d.%02d\n", devc->major, devc->minor));
281 static int sb16_set_dma_hw(sb_devc * devc)
283 int bits;
285 if (devc->dma8 != 0 && devc->dma8 != 1 && devc->dma8 != 3)
287 printk(KERN_ERR "SB16: Invalid 8 bit DMA (%d)\n", devc->dma8);
288 return 0;
290 bits = (1 << devc->dma8);
292 if (devc->dma16 >= 5 && devc->dma16 <= 7)
293 bits |= (1 << devc->dma16);
295 sb_setmixer(devc, DMA_NR, bits);
296 return 1;
299 static void sb16_set_mpu_port(sb_devc * devc, struct address_info *hw_config)
302 * This routine initializes new MIDI port setup register of SB Vibra (CT2502).
304 unsigned char bits = sb_getmixer(devc, 0x84) & ~0x06;
306 switch (hw_config->io_base)
308 case 0x300:
309 sb_setmixer(devc, 0x84, bits | 0x04);
310 break;
312 case 0x330:
313 sb_setmixer(devc, 0x84, bits | 0x00);
314 break;
316 default:
317 sb_setmixer(devc, 0x84, bits | 0x02); /* Disable MPU */
318 printk(KERN_ERR "SB16: Invalid MIDI I/O port %x\n", hw_config->io_base);
322 static int sb16_set_irq_hw(sb_devc * devc, int level)
324 int ival;
326 switch (level)
328 case 5:
329 ival = 2;
330 break;
331 case 7:
332 ival = 4;
333 break;
334 case 9:
335 ival = 1;
336 break;
337 case 10:
338 ival = 8;
339 break;
340 default:
341 printk(KERN_ERR "SB16: Invalid IRQ%d\n", level);
342 return 0;
344 sb_setmixer(devc, IRQ_NR, ival);
345 return 1;
348 static void relocate_Jazz16(sb_devc * devc, struct address_info *hw_config)
350 unsigned char bits = 0;
351 unsigned long flags;
353 if (jazz16_base != 0 && jazz16_base != hw_config->io_base)
354 return;
356 switch (hw_config->io_base)
358 case 0x220:
359 bits = 1;
360 break;
361 case 0x240:
362 bits = 2;
363 break;
364 case 0x260:
365 bits = 3;
366 break;
367 default:
368 return;
370 bits = jazz16_bits = bits << 5;
371 jazz16_base = hw_config->io_base;
374 * Magic wake up sequence by writing to 0x201 (aka Joystick port)
376 spin_lock_irqsave(&jazz16_lock, flags);
377 outb((0xAF), 0x201);
378 outb((0x50), 0x201);
379 outb((bits), 0x201);
380 spin_unlock_irqrestore(&jazz16_lock, flags);
383 static int init_Jazz16(sb_devc * devc, struct address_info *hw_config)
385 char name[100];
387 * First try to check that the card has Jazz16 chip. It identifies itself
388 * by returning 0x12 as response to DSP command 0xfa.
391 if (!sb_dsp_command(devc, 0xfa))
392 return 0;
394 if (sb_dsp_get_byte(devc) != 0x12)
395 return 0;
398 * OK so far. Now configure the IRQ and DMA channel used by the card.
400 if (hw_config->irq < 1 || hw_config->irq > 15 || jazz_irq_bits[hw_config->irq] == 0)
402 printk(KERN_ERR "Jazz16: Invalid interrupt (IRQ%d)\n", hw_config->irq);
403 return 0;
405 if (hw_config->dma < 0 || hw_config->dma > 3 || jazz_dma_bits[hw_config->dma] == 0)
407 printk(KERN_ERR "Jazz16: Invalid 8 bit DMA (DMA%d)\n", hw_config->dma);
408 return 0;
410 if (hw_config->dma2 < 0)
412 printk(KERN_ERR "Jazz16: No 16 bit DMA channel defined\n");
413 return 0;
415 if (hw_config->dma2 < 5 || hw_config->dma2 > 7 || jazz_dma_bits[hw_config->dma2] == 0)
417 printk(KERN_ERR "Jazz16: Invalid 16 bit DMA (DMA%d)\n", hw_config->dma2);
418 return 0;
420 devc->dma16 = hw_config->dma2;
422 if (!sb_dsp_command(devc, 0xfb))
423 return 0;
425 if (!sb_dsp_command(devc, jazz_dma_bits[hw_config->dma] |
426 (jazz_dma_bits[hw_config->dma2] << 4)))
427 return 0;
429 if (!sb_dsp_command(devc, jazz_irq_bits[hw_config->irq]))
430 return 0;
433 * Now we have configured a standard Jazz16 device.
435 devc->model = MDL_JAZZ;
436 strcpy(name, "Jazz16");
438 hw_config->name = "Jazz16";
439 devc->caps |= SB_NO_MIDI;
440 return 1;
443 static void relocate_ess1688(sb_devc * devc)
445 unsigned char bits;
447 switch (devc->base)
449 case 0x220:
450 bits = 0x04;
451 break;
452 case 0x230:
453 bits = 0x05;
454 break;
455 case 0x240:
456 bits = 0x06;
457 break;
458 case 0x250:
459 bits = 0x07;
460 break;
461 default:
462 return; /* Wrong port */
465 DDB(printk("Doing ESS1688 address selection\n"));
468 * ES1688 supports two alternative ways for software address config.
469 * First try the so called Read-Sequence-Key method.
472 /* Reset the sequence logic */
473 inb(0x229);
474 inb(0x229);
475 inb(0x229);
477 /* Perform the read sequence */
478 inb(0x22b);
479 inb(0x229);
480 inb(0x22b);
481 inb(0x229);
482 inb(0x229);
483 inb(0x22b);
484 inb(0x229);
486 /* Select the base address by reading from it. Then probe using the port. */
487 inb(devc->base);
488 if (sb_dsp_reset(devc)) /* Bingo */
489 return;
491 #if 0 /* This causes system lockups (Nokia 386/25 at least) */
493 * The last resort is the system control register method.
496 outb((0x00), 0xfb); /* 0xFB is the unlock register */
497 outb((0x00), 0xe0); /* Select index 0 */
498 outb((bits), 0xe1); /* Write the config bits */
499 outb((0x00), 0xf9); /* 0xFB is the lock register */
500 #endif
503 int sb_dsp_detect(struct address_info *hw_config, int pci, int pciio, struct sb_module_options *sbmo)
505 sb_devc sb_info;
506 sb_devc *devc = &sb_info;
508 memset((char *) &sb_info, 0, sizeof(sb_info)); /* Zero everything */
510 /* Copy module options in place */
511 if(sbmo) memcpy(&devc->sbmo, sbmo, sizeof(struct sb_module_options));
513 sb_info.my_mididev = -1;
514 sb_info.my_mixerdev = -1;
515 sb_info.dev = -1;
518 * Initialize variables
521 DDB(printk("sb_dsp_detect(%x) entered\n", hw_config->io_base));
523 spin_lock_init(&devc->lock);
524 devc->type = hw_config->card_subtype;
526 devc->base = hw_config->io_base;
527 devc->irq = hw_config->irq;
528 devc->dma8 = hw_config->dma;
530 devc->dma16 = -1;
531 devc->pcibase = pciio;
533 if(pci == SB_PCI_ESSMAESTRO)
535 devc->model = MDL_ESSPCI;
536 devc->caps |= SB_PCI_IRQ;
537 hw_config->driver_use_1 |= SB_PCI_IRQ;
538 hw_config->card_subtype = MDL_ESSPCI;
541 if(pci == SB_PCI_YAMAHA)
543 devc->model = MDL_YMPCI;
544 devc->caps |= SB_PCI_IRQ;
545 hw_config->driver_use_1 |= SB_PCI_IRQ;
546 hw_config->card_subtype = MDL_YMPCI;
548 printk("Yamaha PCI mode.\n");
551 if (devc->sbmo.acer)
553 unsigned long flags;
555 spin_lock_irqsave(&devc->lock, flags);
556 inb(devc->base + 0x09);
557 inb(devc->base + 0x09);
558 inb(devc->base + 0x09);
559 inb(devc->base + 0x0b);
560 inb(devc->base + 0x09);
561 inb(devc->base + 0x0b);
562 inb(devc->base + 0x09);
563 inb(devc->base + 0x09);
564 inb(devc->base + 0x0b);
565 inb(devc->base + 0x09);
566 inb(devc->base + 0x00);
567 spin_unlock_irqrestore(&devc->lock, flags);
570 * Detect the device
573 if (sb_dsp_reset(devc))
574 dsp_get_vers(devc);
575 else
576 devc->major = 0;
578 if (devc->type == 0 || devc->type == MDL_JAZZ || devc->type == MDL_SMW)
579 if (devc->major == 0 || (devc->major == 3 && devc->minor == 1))
580 relocate_Jazz16(devc, hw_config);
582 if (devc->major == 0 && (devc->type == MDL_ESS || devc->type == 0))
583 relocate_ess1688(devc);
585 if (!sb_dsp_reset(devc))
587 DDB(printk("SB reset failed\n"));
588 #ifdef MODULE
589 printk(KERN_INFO "sb: dsp reset failed.\n");
590 #endif
591 return 0;
593 if (devc->major == 0)
594 dsp_get_vers(devc);
596 if (devc->major == 3 && devc->minor == 1)
598 if (devc->type == MDL_AZTECH) /* SG Washington? */
600 if (sb_dsp_command(devc, 0x09))
601 if (sb_dsp_command(devc, 0x00)) /* Enter WSS mode */
603 int i;
605 /* Have some delay */
606 for (i = 0; i < 10000; i++)
607 inb(DSP_DATA_AVAIL);
608 devc->caps = SB_NO_AUDIO | SB_NO_MIDI; /* Mixer only */
609 devc->model = MDL_AZTECH;
614 if(devc->type == MDL_ESSPCI)
615 devc->model = MDL_ESSPCI;
617 if(devc->type == MDL_YMPCI)
619 printk("YMPCI selected\n");
620 devc->model = MDL_YMPCI;
624 * Save device information for sb_dsp_init()
628 detected_devc = kmalloc(sizeof(sb_devc), GFP_KERNEL);
629 if (detected_devc == NULL)
631 printk(KERN_ERR "sb: Can't allocate memory for device information\n");
632 return 0;
634 memcpy(detected_devc, devc, sizeof(sb_devc));
635 MDB(printk(KERN_INFO "SB %d.%02d detected OK (%x)\n", devc->major, devc->minor, hw_config->io_base));
636 return 1;
639 int sb_dsp_init(struct address_info *hw_config, struct module *owner)
641 sb_devc *devc;
642 char name[100];
643 extern int sb_be_quiet;
644 int mixer22, mixer30;
647 * Check if we had detected a SB device earlier
649 DDB(printk("sb_dsp_init(%x) entered\n", hw_config->io_base));
650 name[0] = 0;
652 if (detected_devc == NULL)
654 MDB(printk("No detected device\n"));
655 return 0;
657 devc = detected_devc;
658 detected_devc = NULL;
660 if (devc->base != hw_config->io_base)
662 DDB(printk("I/O port mismatch\n"));
663 release_region(devc->base, 16);
664 return 0;
667 * Now continue initialization of the device
670 devc->caps = hw_config->driver_use_1;
672 if (!((devc->caps & SB_NO_AUDIO) && (devc->caps & SB_NO_MIDI)) && hw_config->irq > 0)
673 { /* IRQ setup */
676 * ESS PCI cards do shared PCI IRQ stuff. Since they
677 * will get shared PCI irq lines we must cope.
680 int i=(devc->caps&SB_PCI_IRQ)?IRQF_SHARED:0;
682 if (request_irq(hw_config->irq, sbintr, i, "soundblaster", devc) < 0)
684 printk(KERN_ERR "SB: Can't allocate IRQ%d\n", hw_config->irq);
685 release_region(devc->base, 16);
686 return 0;
688 devc->irq_ok = 0;
690 if (devc->major == 4)
691 if (!sb16_set_irq_hw(devc, devc->irq)) /* Unsupported IRQ */
693 free_irq(devc->irq, devc);
694 release_region(devc->base, 16);
695 return 0;
697 if ((devc->type == 0 || devc->type == MDL_ESS) &&
698 devc->major == 3 && devc->minor == 1)
699 { /* Handle various chipsets which claim they are SB Pro compatible */
700 if ((devc->type != 0 && devc->type != MDL_ESS) ||
701 !ess_init(devc, hw_config))
703 if ((devc->type != 0 && devc->type != MDL_JAZZ &&
704 devc->type != MDL_SMW) || !init_Jazz16(devc, hw_config))
706 DDB(printk("This is a genuine SB Pro\n"));
710 if (devc->major == 4 && devc->minor <= 11 ) /* Won't work */
711 devc->irq_ok = 1;
712 else
714 int n;
716 for (n = 0; n < 3 && devc->irq_ok == 0; n++)
718 if (sb_dsp_command(devc, 0xf2)) /* Cause interrupt immediately */
720 int i;
722 for (i = 0; !devc->irq_ok && i < 10000; i++);
725 if (!devc->irq_ok)
726 printk(KERN_WARNING "sb: Interrupt test on IRQ%d failed - Probable IRQ conflict\n", devc->irq);
727 else
729 DDB(printk("IRQ test OK (IRQ%d)\n", devc->irq));
732 } /* IRQ setup */
734 last_sb = devc;
736 switch (devc->major)
738 case 1: /* SB 1.0 or 1.5 */
739 devc->model = hw_config->card_subtype = MDL_SB1;
740 break;
742 case 2: /* SB 2.x */
743 if (devc->minor == 0)
744 devc->model = hw_config->card_subtype = MDL_SB2;
745 else
746 devc->model = hw_config->card_subtype = MDL_SB201;
747 break;
749 case 3: /* SB Pro and most clones */
750 switch (devc->model) {
751 case 0:
752 devc->model = hw_config->card_subtype = MDL_SBPRO;
753 if (hw_config->name == NULL)
754 hw_config->name = "Sound Blaster Pro (8 BIT ONLY)";
755 break;
756 case MDL_ESS:
757 ess_dsp_init(devc, hw_config);
758 break;
760 break;
762 case 4:
763 devc->model = hw_config->card_subtype = MDL_SB16;
765 * ALS007 and ALS100 return DSP version 4.2 and have 2 post-reset !=0
766 * registers at 0x3c and 0x4c (output ctrl registers on ALS007) whereas
767 * a "standard" SB16 doesn't have a register at 0x4c. ALS100 actively
768 * updates register 0x22 whenever 0x30 changes, as per the SB16 spec.
769 * Since ALS007 doesn't, this can be used to differentiate the 2 cards.
771 if ((devc->minor == 2) && sb_getmixer(devc,0x3c) && sb_getmixer(devc,0x4c))
773 mixer30 = sb_getmixer(devc,0x30);
774 sb_setmixer(devc,0x22,(mixer22=sb_getmixer(devc,0x22)) & 0x0f);
775 sb_setmixer(devc,0x30,0xff);
776 /* ALS100 will force 0x30 to 0xf8 like SB16; ALS007 will allow 0xff. */
777 /* Register 0x22 & 0xf0 on ALS100 == 0xf0; on ALS007 it == 0x10. */
778 if ((sb_getmixer(devc,0x30) != 0xff) || ((sb_getmixer(devc,0x22) & 0xf0) != 0x10))
780 devc->submodel = SUBMDL_ALS100;
781 if (hw_config->name == NULL)
782 hw_config->name = "Sound Blaster 16 (ALS-100)";
784 else
786 sb_setmixer(devc,0x3c,0x1f); /* Enable all inputs */
787 sb_setmixer(devc,0x4c,0x1f);
788 sb_setmixer(devc,0x22,mixer22); /* Restore 0x22 to original value */
789 devc->submodel = SUBMDL_ALS007;
790 if (hw_config->name == NULL)
791 hw_config->name = "Sound Blaster 16 (ALS-007)";
793 sb_setmixer(devc,0x30,mixer30);
795 else if (hw_config->name == NULL)
796 hw_config->name = "Sound Blaster 16";
798 if (hw_config->dma2 == -1)
799 devc->dma16 = devc->dma8;
800 else if (hw_config->dma2 < 5 || hw_config->dma2 > 7)
802 printk(KERN_WARNING "SB16: Bad or missing 16 bit DMA channel\n");
803 devc->dma16 = devc->dma8;
805 else
806 devc->dma16 = hw_config->dma2;
808 if(!sb16_set_dma_hw(devc)) {
809 free_irq(devc->irq, devc);
810 release_region(hw_config->io_base, 16);
811 return 0;
814 devc->caps |= SB_NO_MIDI;
817 if (!(devc->caps & SB_NO_MIXER))
818 if (devc->major == 3 || devc->major == 4)
819 sb_mixer_init(devc, owner);
821 if (!(devc->caps & SB_NO_MIDI))
822 sb_dsp_midi_init(devc, owner);
824 if (hw_config->name == NULL)
825 hw_config->name = "Sound Blaster (8 BIT/MONO ONLY)";
827 sprintf(name, "%s (%d.%02d)", hw_config->name, devc->major, devc->minor);
828 conf_printf(name, hw_config);
831 * Assuming that a sound card is Sound Blaster (compatible) is the most common
832 * configuration error and the mother of all problems. Usually sound cards
833 * emulate SB Pro but in addition they have a 16 bit native mode which should be
834 * used in Unix. See Readme.cards for more information about configuring OSS/Free
835 * properly.
837 if (devc->model <= MDL_SBPRO)
839 if (devc->major == 3 && devc->minor != 1) /* "True" SB Pro should have v3.1 (rare ones may have 3.2). */
841 printk(KERN_INFO "This sound card may not be fully Sound Blaster Pro compatible.\n");
842 printk(KERN_INFO "In many cases there is another way to configure OSS so that\n");
843 printk(KERN_INFO "it works properly with OSS (for example in 16 bit mode).\n");
844 printk(KERN_INFO "Please ignore this message if you _really_ have a SB Pro.\n");
846 else if (!sb_be_quiet && devc->model == MDL_SBPRO)
848 printk(KERN_INFO "SB DSP version is just %d.%02d which means that your card is\n", devc->major, devc->minor);
849 printk(KERN_INFO "several years old (8 bit only device) or alternatively the sound driver\n");
850 printk(KERN_INFO "is incorrectly configured.\n");
853 hw_config->card_subtype = devc->model;
854 hw_config->slots[0]=devc->dev;
855 last_devc = devc; /* For SB MPU detection */
857 if (!(devc->caps & SB_NO_AUDIO) && devc->dma8 >= 0)
859 if (sound_alloc_dma(devc->dma8, "SoundBlaster8"))
861 printk(KERN_WARNING "Sound Blaster: Can't allocate 8 bit DMA channel %d\n", devc->dma8);
863 if (devc->dma16 >= 0 && devc->dma16 != devc->dma8)
865 if (sound_alloc_dma(devc->dma16, "SoundBlaster16"))
866 printk(KERN_WARNING "Sound Blaster: can't allocate 16 bit DMA channel %d.\n", devc->dma16);
868 sb_audio_init(devc, name, owner);
869 hw_config->slots[0]=devc->dev;
871 else
873 MDB(printk("Sound Blaster: no audio devices found.\n"));
875 return 1;
878 /* if (sbmpu) below we allow mpu401 to manage the midi devs
879 otherwise we have to unload them. (Andrzej Krzysztofowicz) */
881 void sb_dsp_unload(struct address_info *hw_config, int sbmpu)
883 sb_devc *devc;
885 devc = audio_devs[hw_config->slots[0]]->devc;
887 if (devc && devc->base == hw_config->io_base)
889 if ((devc->model & MDL_ESS) && devc->pcibase)
890 release_region(devc->pcibase, 8);
892 release_region(devc->base, 16);
894 if (!(devc->caps & SB_NO_AUDIO))
896 sound_free_dma(devc->dma8);
897 if (devc->dma16 >= 0)
898 sound_free_dma(devc->dma16);
900 if (!(devc->caps & SB_NO_AUDIO && devc->caps & SB_NO_MIDI))
902 if (devc->irq > 0)
903 free_irq(devc->irq, devc);
905 sb_mixer_unload(devc);
906 /* We don't have to do this bit any more the UART401 is its own
907 master -- Krzysztof Halasa */
908 /* But we have to do it, if UART401 is not detected */
909 if (!sbmpu)
910 sound_unload_mididev(devc->my_mididev);
911 sound_unload_audiodev(devc->dev);
913 kfree(devc);
915 else
916 release_region(hw_config->io_base, 16);
918 kfree(detected_devc);
922 * Mixer access routines
924 * ES1887 modifications: some mixer registers reside in the
925 * range above 0xa0. These must be accessed in another way.
928 void sb_setmixer(sb_devc * devc, unsigned int port, unsigned int value)
930 unsigned long flags;
932 if (devc->model == MDL_ESS) {
933 ess_setmixer (devc, port, value);
934 return;
937 spin_lock_irqsave(&devc->lock, flags);
939 outb(((unsigned char) (port & 0xff)), MIXER_ADDR);
940 udelay(20);
941 outb(((unsigned char) (value & 0xff)), MIXER_DATA);
942 udelay(20);
944 spin_unlock_irqrestore(&devc->lock, flags);
947 unsigned int sb_getmixer(sb_devc * devc, unsigned int port)
949 unsigned int val;
950 unsigned long flags;
952 if (devc->model == MDL_ESS) return ess_getmixer (devc, port);
954 spin_lock_irqsave(&devc->lock, flags);
956 outb(((unsigned char) (port & 0xff)), MIXER_ADDR);
957 udelay(20);
958 val = inb(MIXER_DATA);
959 udelay(20);
961 spin_unlock_irqrestore(&devc->lock, flags);
963 return val;
966 void sb_chgmixer
967 (sb_devc * devc, unsigned int reg, unsigned int mask, unsigned int val)
969 int value;
971 value = sb_getmixer(devc, reg);
972 value = (value & ~mask) | (val & mask);
973 sb_setmixer(devc, reg, value);
977 * MPU401 MIDI initialization.
980 static void smw_putmem(sb_devc * devc, int base, int addr, unsigned char val)
982 unsigned long flags;
984 spin_lock_irqsave(&jazz16_lock, flags); /* NOT the SB card? */
986 outb((addr & 0xff), base + 1); /* Low address bits */
987 outb((addr >> 8), base + 2); /* High address bits */
988 outb((val), base); /* Data */
990 spin_unlock_irqrestore(&jazz16_lock, flags);
993 static unsigned char smw_getmem(sb_devc * devc, int base, int addr)
995 unsigned long flags;
996 unsigned char val;
998 spin_lock_irqsave(&jazz16_lock, flags); /* NOT the SB card? */
1000 outb((addr & 0xff), base + 1); /* Low address bits */
1001 outb((addr >> 8), base + 2); /* High address bits */
1002 val = inb(base); /* Data */
1004 spin_unlock_irqrestore(&jazz16_lock, flags);
1005 return val;
1008 static int smw_midi_init(sb_devc * devc, struct address_info *hw_config)
1010 int mpu_base = hw_config->io_base;
1011 int mp_base = mpu_base + 4; /* Microcontroller base */
1012 int i;
1013 unsigned char control;
1017 * Reset the microcontroller so that the RAM can be accessed
1020 control = inb(mpu_base + 7);
1021 outb((control | 3), mpu_base + 7); /* Set last two bits to 1 (?) */
1022 outb(((control & 0xfe) | 2), mpu_base + 7); /* xxxxxxx0 resets the mc */
1024 mdelay(3); /* Wait at least 1ms */
1026 outb((control & 0xfc), mpu_base + 7); /* xxxxxx00 enables RAM */
1029 * Detect microcontroller by probing the 8k RAM area
1031 smw_putmem(devc, mp_base, 0, 0x00);
1032 smw_putmem(devc, mp_base, 1, 0xff);
1033 udelay(10);
1035 if (smw_getmem(devc, mp_base, 0) != 0x00 || smw_getmem(devc, mp_base, 1) != 0xff)
1037 DDB(printk("SM Wave: No microcontroller RAM detected (%02x, %02x)\n", smw_getmem(devc, mp_base, 0), smw_getmem(devc, mp_base, 1)));
1038 return 0; /* No RAM */
1041 * There is RAM so assume it's really a SM Wave
1044 devc->model = MDL_SMW;
1045 smw_mixer_init(devc);
1047 #ifdef MODULE
1048 if (!smw_ucode)
1050 smw_ucodeLen = mod_firmware_load("/etc/sound/midi0001.bin", (void *) &smw_ucode);
1051 smw_free = smw_ucode;
1053 #endif
1054 if (smw_ucodeLen > 0)
1056 if (smw_ucodeLen != 8192)
1058 printk(KERN_ERR "SM Wave: Invalid microcode (MIDI0001.BIN) length\n");
1059 return 1;
1062 * Download microcode
1065 for (i = 0; i < 8192; i++)
1066 smw_putmem(devc, mp_base, i, smw_ucode[i]);
1069 * Verify microcode
1072 for (i = 0; i < 8192; i++)
1073 if (smw_getmem(devc, mp_base, i) != smw_ucode[i])
1075 printk(KERN_ERR "SM Wave: Microcode verification failed\n");
1076 return 0;
1079 control = 0;
1080 #ifdef SMW_SCSI_IRQ
1082 * Set the SCSI interrupt (IRQ2/9, IRQ3 or IRQ10). The SCSI interrupt
1083 * is disabled by default.
1085 * FIXME - make this a module option
1087 * BTW the Zilog 5380 SCSI controller is located at MPU base + 0x10.
1090 static unsigned char scsi_irq_bits[] = {
1091 0, 0, 3, 1, 0, 0, 0, 0, 0, 3, 2, 0, 0, 0, 0, 0
1093 control |= scsi_irq_bits[SMW_SCSI_IRQ] << 6;
1095 #endif
1097 #ifdef SMW_OPL4_ENABLE
1099 * Make the OPL4 chip visible on the PC bus at 0x380.
1101 * There is no need to enable this feature since this driver
1102 * doesn't support OPL4 yet. Also there is no RAM in SM Wave so
1103 * enabling OPL4 is pretty useless.
1105 control |= 0x10; /* Uses IRQ12 if bit 0x20 == 0 */
1106 /* control |= 0x20; Uncomment this if you want to use IRQ7 */
1107 #endif
1108 outb((control | 0x03), mpu_base + 7); /* xxxxxx11 restarts */
1109 hw_config->name = "SoundMan Wave";
1110 return 1;
1113 static int init_Jazz16_midi(sb_devc * devc, struct address_info *hw_config)
1115 int mpu_base = hw_config->io_base;
1116 int sb_base = devc->base;
1117 int irq = hw_config->irq;
1119 unsigned char bits = 0;
1120 unsigned long flags;
1122 if (irq < 0)
1123 irq *= -1;
1125 if (irq < 1 || irq > 15 ||
1126 jazz_irq_bits[irq] == 0)
1128 printk(KERN_ERR "Jazz16: Invalid MIDI interrupt (IRQ%d)\n", irq);
1129 return 0;
1131 switch (sb_base)
1133 case 0x220:
1134 bits = 1;
1135 break;
1136 case 0x240:
1137 bits = 2;
1138 break;
1139 case 0x260:
1140 bits = 3;
1141 break;
1142 default:
1143 return 0;
1145 bits = jazz16_bits = bits << 5;
1146 switch (mpu_base)
1148 case 0x310:
1149 bits |= 1;
1150 break;
1151 case 0x320:
1152 bits |= 2;
1153 break;
1154 case 0x330:
1155 bits |= 3;
1156 break;
1157 default:
1158 printk(KERN_ERR "Jazz16: Invalid MIDI I/O port %x\n", mpu_base);
1159 return 0;
1162 * Magic wake up sequence by writing to 0x201 (aka Joystick port)
1164 spin_lock_irqsave(&jazz16_lock, flags);
1165 outb(0xAF, 0x201);
1166 outb(0x50, 0x201);
1167 outb(bits, 0x201);
1168 spin_unlock_irqrestore(&jazz16_lock, flags);
1170 hw_config->name = "Jazz16";
1171 smw_midi_init(devc, hw_config);
1173 if (!sb_dsp_command(devc, 0xfb))
1174 return 0;
1176 if (!sb_dsp_command(devc, jazz_dma_bits[devc->dma8] |
1177 (jazz_dma_bits[devc->dma16] << 4)))
1178 return 0;
1180 if (!sb_dsp_command(devc, jazz_irq_bits[devc->irq] |
1181 (jazz_irq_bits[irq] << 4)))
1182 return 0;
1184 return 1;
1187 int probe_sbmpu(struct address_info *hw_config, struct module *owner)
1189 sb_devc *devc = last_devc;
1190 int ret;
1192 if (last_devc == NULL)
1193 return 0;
1195 last_devc = NULL;
1197 if (hw_config->io_base <= 0)
1199 /* The real vibra16 is fine about this, but we have to go
1200 wipe up after Cyrix again */
1202 if(devc->model == MDL_SB16 && devc->minor >= 12)
1204 unsigned char bits = sb_getmixer(devc, 0x84) & ~0x06;
1205 sb_setmixer(devc, 0x84, bits | 0x02); /* Disable MPU */
1207 return 0;
1210 #if defined(CONFIG_SOUND_MPU401)
1211 if (devc->model == MDL_ESS)
1213 struct resource *ports;
1214 ports = request_region(hw_config->io_base, 2, "mpu401");
1215 if (!ports) {
1216 printk(KERN_ERR "sbmpu: I/O port conflict (%x)\n", hw_config->io_base);
1217 return 0;
1219 if (!ess_midi_init(devc, hw_config)) {
1220 release_region(hw_config->io_base, 2);
1221 return 0;
1223 hw_config->name = "ESS1xxx MPU";
1224 devc->midi_irq_cookie = NULL;
1225 if (!probe_mpu401(hw_config, ports)) {
1226 release_region(hw_config->io_base, 2);
1227 return 0;
1229 attach_mpu401(hw_config, owner);
1230 if (last_sb->irq == -hw_config->irq)
1231 last_sb->midi_irq_cookie =
1232 (void *)(long) hw_config->slots[1];
1233 return 1;
1235 #endif
1237 switch (devc->model)
1239 case MDL_SB16:
1240 if (hw_config->io_base != 0x300 && hw_config->io_base != 0x330)
1242 printk(KERN_ERR "SB16: Invalid MIDI port %x\n", hw_config->io_base);
1243 return 0;
1245 hw_config->name = "Sound Blaster 16";
1246 if (hw_config->irq < 3 || hw_config->irq == devc->irq)
1247 hw_config->irq = -devc->irq;
1248 if (devc->minor > 12) /* What is Vibra's version??? */
1249 sb16_set_mpu_port(devc, hw_config);
1250 break;
1252 case MDL_JAZZ:
1253 if (hw_config->irq < 3 || hw_config->irq == devc->irq)
1254 hw_config->irq = -devc->irq;
1255 if (!init_Jazz16_midi(devc, hw_config))
1256 return 0;
1257 break;
1259 case MDL_YMPCI:
1260 hw_config->name = "Yamaha PCI Legacy";
1261 printk("Yamaha PCI legacy UART401 check.\n");
1262 break;
1263 default:
1264 return 0;
1267 ret = probe_uart401(hw_config, owner);
1268 if (ret)
1269 last_sb->midi_irq_cookie=midi_devs[hw_config->slots[4]]->devc;
1270 return ret;
1273 void unload_sbmpu(struct address_info *hw_config)
1275 #if defined(CONFIG_SOUND_MPU401)
1276 if (!strcmp (hw_config->name, "ESS1xxx MPU")) {
1277 unload_mpu401(hw_config);
1278 return;
1280 #endif
1281 unload_uart401(hw_config);
1284 EXPORT_SYMBOL(sb_dsp_init);
1285 EXPORT_SYMBOL(sb_dsp_detect);
1286 EXPORT_SYMBOL(sb_dsp_unload);
1287 EXPORT_SYMBOL(sb_be_quiet);
1288 EXPORT_SYMBOL(probe_sbmpu);
1289 EXPORT_SYMBOL(unload_sbmpu);
1290 EXPORT_SYMBOL(smw_free);
1291 MODULE_LICENSE("GPL");