cmd64x: don't clear the other channel's interrupt
[linux-2.6/linux-mips/linux-dm7025.git] / drivers / ide / cris / ide-cris.c
blobe196aefa2070c2f2c54e79498cfc1dcf5e19e419
1 /* $Id: cris-ide-driver.patch,v 1.1 2005/06/29 21:39:07 akpm Exp $
3 * Etrax specific IDE functions, like init and PIO-mode setting etc.
4 * Almost the entire ide.c is used for the rest of the Etrax ATA driver.
5 * Copyright (c) 2000-2005 Axis Communications AB
7 * Authors: Bjorn Wesen (initial version)
8 * Mikael Starvik (crisv32 port)
9 */
11 /* Regarding DMA:
13 * There are two forms of DMA - "DMA handshaking" between the interface and the drive,
14 * and DMA between the memory and the interface. We can ALWAYS use the latter, since it's
15 * something built-in in the Etrax. However only some drives support the DMA-mode handshaking
16 * on the ATA-bus. The normal PC driver and Triton interface disables memory-if DMA when the
17 * device can't do DMA handshaking for some stupid reason. We don't need to do that.
20 #include <linux/types.h>
21 #include <linux/kernel.h>
22 #include <linux/timer.h>
23 #include <linux/mm.h>
24 #include <linux/interrupt.h>
25 #include <linux/delay.h>
26 #include <linux/blkdev.h>
27 #include <linux/hdreg.h>
28 #include <linux/ide.h>
29 #include <linux/init.h>
31 #include <asm/io.h>
32 #include <asm/dma.h>
34 /* number of DMA descriptors */
35 #define MAX_DMA_DESCRS 64
37 /* number of times to retry busy-flags when reading/writing IDE-registers
38 * this can't be too high because a hung harddisk might cause the watchdog
39 * to trigger (sometimes INB and OUTB are called with irq's disabled)
42 #define IDE_REGISTER_TIMEOUT 300
44 #define LOWDB(x)
45 #define D(x)
47 enum /* Transfer types */
49 TYPE_PIO,
50 TYPE_DMA,
51 TYPE_UDMA
54 /* CRISv32 specifics */
55 #ifdef CONFIG_ETRAX_ARCH_V32
56 #include <asm/arch/hwregs/ata_defs.h>
57 #include <asm/arch/hwregs/dma_defs.h>
58 #include <asm/arch/hwregs/dma.h>
59 #include <asm/arch/pinmux.h>
61 #define ATA_UDMA2_CYC 2
62 #define ATA_UDMA2_DVS 3
63 #define ATA_UDMA1_CYC 2
64 #define ATA_UDMA1_DVS 4
65 #define ATA_UDMA0_CYC 4
66 #define ATA_UDMA0_DVS 6
67 #define ATA_DMA2_STROBE 7
68 #define ATA_DMA2_HOLD 1
69 #define ATA_DMA1_STROBE 8
70 #define ATA_DMA1_HOLD 3
71 #define ATA_DMA0_STROBE 25
72 #define ATA_DMA0_HOLD 19
73 #define ATA_PIO4_SETUP 3
74 #define ATA_PIO4_STROBE 7
75 #define ATA_PIO4_HOLD 1
76 #define ATA_PIO3_SETUP 3
77 #define ATA_PIO3_STROBE 9
78 #define ATA_PIO3_HOLD 3
79 #define ATA_PIO2_SETUP 3
80 #define ATA_PIO2_STROBE 13
81 #define ATA_PIO2_HOLD 5
82 #define ATA_PIO1_SETUP 5
83 #define ATA_PIO1_STROBE 23
84 #define ATA_PIO1_HOLD 9
85 #define ATA_PIO0_SETUP 9
86 #define ATA_PIO0_STROBE 39
87 #define ATA_PIO0_HOLD 9
89 int
90 cris_ide_ack_intr(ide_hwif_t* hwif)
92 reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2,
93 int, hwif->io_ports[0]);
94 REG_WR_INT(ata, regi_ata, rw_ack_intr, 1 << ctrl2.sel);
95 return 1;
98 static inline int
99 cris_ide_busy(void)
101 reg_ata_rs_stat_data stat_data;
102 stat_data = REG_RD(ata, regi_ata, rs_stat_data);
103 return stat_data.busy;
106 static inline int
107 cris_ide_ready(void)
109 return !cris_ide_busy();
112 static inline int
113 cris_ide_data_available(unsigned short* data)
115 reg_ata_rs_stat_data stat_data;
116 stat_data = REG_RD(ata, regi_ata, rs_stat_data);
117 *data = stat_data.data;
118 return stat_data.dav;
121 static void
122 cris_ide_write_command(unsigned long command)
124 REG_WR_INT(ata, regi_ata, rw_ctrl2, command); /* write data to the drive's register */
127 static void
128 cris_ide_set_speed(int type, int setup, int strobe, int hold)
130 reg_ata_rw_ctrl0 ctrl0 = REG_RD(ata, regi_ata, rw_ctrl0);
131 reg_ata_rw_ctrl1 ctrl1 = REG_RD(ata, regi_ata, rw_ctrl1);
133 if (type == TYPE_PIO) {
134 ctrl0.pio_setup = setup;
135 ctrl0.pio_strb = strobe;
136 ctrl0.pio_hold = hold;
137 } else if (type == TYPE_DMA) {
138 ctrl0.dma_strb = strobe;
139 ctrl0.dma_hold = hold;
140 } else if (type == TYPE_UDMA) {
141 ctrl1.udma_tcyc = setup;
142 ctrl1.udma_tdvs = strobe;
144 REG_WR(ata, regi_ata, rw_ctrl0, ctrl0);
145 REG_WR(ata, regi_ata, rw_ctrl1, ctrl1);
148 static unsigned long
149 cris_ide_base_address(int bus)
151 reg_ata_rw_ctrl2 ctrl2 = {0};
152 ctrl2.sel = bus;
153 return REG_TYPE_CONV(int, reg_ata_rw_ctrl2, ctrl2);
156 static unsigned long
157 cris_ide_reg_addr(unsigned long addr, int cs0, int cs1)
159 reg_ata_rw_ctrl2 ctrl2 = {0};
160 ctrl2.addr = addr;
161 ctrl2.cs1 = cs1;
162 ctrl2.cs0 = cs0;
163 return REG_TYPE_CONV(int, reg_ata_rw_ctrl2, ctrl2);
166 static __init void
167 cris_ide_reset(unsigned val)
169 reg_ata_rw_ctrl0 ctrl0 = {0};
170 ctrl0.rst = val ? regk_ata_active : regk_ata_inactive;
171 REG_WR(ata, regi_ata, rw_ctrl0, ctrl0);
174 static __init void
175 cris_ide_init(void)
177 reg_ata_rw_ctrl0 ctrl0 = {0};
178 reg_ata_rw_intr_mask intr_mask = {0};
180 ctrl0.en = regk_ata_yes;
181 REG_WR(ata, regi_ata, rw_ctrl0, ctrl0);
183 intr_mask.bus0 = regk_ata_yes;
184 intr_mask.bus1 = regk_ata_yes;
185 intr_mask.bus2 = regk_ata_yes;
186 intr_mask.bus3 = regk_ata_yes;
188 REG_WR(ata, regi_ata, rw_intr_mask, intr_mask);
190 crisv32_request_dma(2, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata);
191 crisv32_request_dma(3, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata);
193 crisv32_pinmux_alloc_fixed(pinmux_ata);
194 crisv32_pinmux_alloc_fixed(pinmux_ata0);
195 crisv32_pinmux_alloc_fixed(pinmux_ata1);
196 crisv32_pinmux_alloc_fixed(pinmux_ata2);
197 crisv32_pinmux_alloc_fixed(pinmux_ata3);
199 DMA_RESET(regi_dma2);
200 DMA_ENABLE(regi_dma2);
201 DMA_RESET(regi_dma3);
202 DMA_ENABLE(regi_dma3);
204 DMA_WR_CMD (regi_dma2, regk_dma_set_w_size2);
205 DMA_WR_CMD (regi_dma3, regk_dma_set_w_size2);
208 static dma_descr_context mycontext __attribute__ ((__aligned__(32)));
210 #define cris_dma_descr_type dma_descr_data
211 #define cris_pio_read regk_ata_rd
212 #define cris_ultra_mask 0x7
213 #define MAX_DESCR_SIZE 0xffffffffUL
215 static unsigned long
216 cris_ide_get_reg(unsigned long reg)
218 return (reg & 0x0e000000) >> 25;
221 static void
222 cris_ide_fill_descriptor(cris_dma_descr_type *d, void* buf, unsigned int len, int last)
224 d->buf = (char*)virt_to_phys(buf);
225 d->after = d->buf + len;
226 d->eol = last;
229 static void
230 cris_ide_start_dma(ide_drive_t *drive, cris_dma_descr_type *d, int dir,int type,int len)
232 reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, int, IDE_DATA_REG);
233 reg_ata_rw_trf_cnt trf_cnt = {0};
235 mycontext.saved_data = (dma_descr_data*)virt_to_phys(d);
236 mycontext.saved_data_buf = d->buf;
237 /* start the dma channel */
238 DMA_START_CONTEXT(dir ? regi_dma3 : regi_dma2, virt_to_phys(&mycontext));
240 /* initiate a multi word dma read using PIO handshaking */
241 trf_cnt.cnt = len >> 1;
242 /* Due to a "feature" the transfer count has to be one extra word for UDMA. */
243 if (type == TYPE_UDMA)
244 trf_cnt.cnt++;
245 REG_WR(ata, regi_ata, rw_trf_cnt, trf_cnt);
247 ctrl2.rw = dir ? regk_ata_rd : regk_ata_wr;
248 ctrl2.trf_mode = regk_ata_dma;
249 ctrl2.hsh = type == TYPE_PIO ? regk_ata_pio :
250 type == TYPE_DMA ? regk_ata_dma : regk_ata_udma;
251 ctrl2.multi = regk_ata_yes;
252 ctrl2.dma_size = regk_ata_word;
253 REG_WR(ata, regi_ata, rw_ctrl2, ctrl2);
256 static void
257 cris_ide_wait_dma(int dir)
259 reg_dma_rw_stat status;
262 status = REG_RD(dma, dir ? regi_dma3 : regi_dma2, rw_stat);
263 } while(status.list_state != regk_dma_data_at_eol);
266 static int cris_dma_test_irq(ide_drive_t *drive)
268 int intr = REG_RD_INT(ata, regi_ata, r_intr);
269 reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, int, IDE_DATA_REG);
270 return intr & (1 << ctrl2.sel) ? 1 : 0;
273 static void cris_ide_initialize_dma(int dir)
277 #else
278 /* CRISv10 specifics */
279 #include <asm/arch/svinto.h>
280 #include <asm/arch/io_interface_mux.h>
282 /* PIO timing (in R_ATA_CONFIG)
284 * _____________________________
285 * ADDRESS : ________/
287 * _______________
288 * DIOR : ____________/ \__________
290 * _______________
291 * DATA : XXXXXXXXXXXXXXXX_______________XXXXXXXX
294 * DIOR is unbuffered while address and data is buffered.
295 * This creates two problems:
296 * 1. The DIOR pulse is to early (because it is unbuffered)
297 * 2. The rise time of DIOR is long
299 * There are at least three different plausible solutions
300 * 1. Use a pad capable of larger currents in Etrax
301 * 2. Use an external buffer
302 * 3. Make the strobe pulse longer
304 * Some of the strobe timings below are modified to compensate
305 * for this. This implies a slight performance decrease.
307 * THIS SHOULD NEVER BE CHANGED!
309 * TODO: Is this true for the latest LX boards still ?
312 #define ATA_UDMA2_CYC 0 /* No UDMA supported, just to make it compile. */
313 #define ATA_UDMA2_DVS 0
314 #define ATA_UDMA1_CYC 0
315 #define ATA_UDMA1_DVS 0
316 #define ATA_UDMA0_CYC 0
317 #define ATA_UDMA0_DVS 0
318 #define ATA_DMA2_STROBE 4
319 #define ATA_DMA2_HOLD 0
320 #define ATA_DMA1_STROBE 4
321 #define ATA_DMA1_HOLD 1
322 #define ATA_DMA0_STROBE 12
323 #define ATA_DMA0_HOLD 9
324 #define ATA_PIO4_SETUP 1
325 #define ATA_PIO4_STROBE 5
326 #define ATA_PIO4_HOLD 0
327 #define ATA_PIO3_SETUP 1
328 #define ATA_PIO3_STROBE 5
329 #define ATA_PIO3_HOLD 1
330 #define ATA_PIO2_SETUP 1
331 #define ATA_PIO2_STROBE 6
332 #define ATA_PIO2_HOLD 2
333 #define ATA_PIO1_SETUP 2
334 #define ATA_PIO1_STROBE 11
335 #define ATA_PIO1_HOLD 4
336 #define ATA_PIO0_SETUP 4
337 #define ATA_PIO0_STROBE 19
338 #define ATA_PIO0_HOLD 4
341 cris_ide_ack_intr(ide_hwif_t* hwif)
343 return 1;
346 static inline int
347 cris_ide_busy(void)
349 return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy) ;
352 static inline int
353 cris_ide_ready(void)
355 return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, tr_rdy) ;
358 static inline int
359 cris_ide_data_available(unsigned short* data)
361 unsigned long status = *R_ATA_STATUS_DATA;
362 *data = (unsigned short)status;
363 return status & IO_MASK(R_ATA_STATUS_DATA, dav);
366 static void
367 cris_ide_write_command(unsigned long command)
369 *R_ATA_CTRL_DATA = command;
372 static void
373 cris_ide_set_speed(int type, int setup, int strobe, int hold)
375 static int pio_setup = ATA_PIO4_SETUP;
376 static int pio_strobe = ATA_PIO4_STROBE;
377 static int pio_hold = ATA_PIO4_HOLD;
378 static int dma_strobe = ATA_DMA2_STROBE;
379 static int dma_hold = ATA_DMA2_HOLD;
381 if (type == TYPE_PIO) {
382 pio_setup = setup;
383 pio_strobe = strobe;
384 pio_hold = hold;
385 } else if (type == TYPE_DMA) {
386 dma_strobe = strobe;
387 dma_hold = hold;
389 *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ) |
390 IO_FIELD( R_ATA_CONFIG, dma_strobe, dma_strobe ) |
391 IO_FIELD( R_ATA_CONFIG, dma_hold, dma_hold ) |
392 IO_FIELD( R_ATA_CONFIG, pio_setup, pio_setup ) |
393 IO_FIELD( R_ATA_CONFIG, pio_strobe, pio_strobe ) |
394 IO_FIELD( R_ATA_CONFIG, pio_hold, pio_hold ) );
397 static unsigned long
398 cris_ide_base_address(int bus)
400 return IO_FIELD(R_ATA_CTRL_DATA, sel, bus);
403 static unsigned long
404 cris_ide_reg_addr(unsigned long addr, int cs0, int cs1)
406 return IO_FIELD(R_ATA_CTRL_DATA, addr, addr) |
407 IO_FIELD(R_ATA_CTRL_DATA, cs0, cs0) |
408 IO_FIELD(R_ATA_CTRL_DATA, cs1, cs1);
411 static __init void
412 cris_ide_reset(unsigned val)
414 #ifdef CONFIG_ETRAX_IDE_G27_RESET
415 REG_SHADOW_SET(R_PORT_G_DATA, port_g_data_shadow, 27, val);
416 #endif
417 #ifdef CONFIG_ETRAX_IDE_PB7_RESET
418 port_pb_dir_shadow = port_pb_dir_shadow |
419 IO_STATE(R_PORT_PB_DIR, dir7, output);
420 *R_PORT_PB_DIR = port_pb_dir_shadow;
421 REG_SHADOW_SET(R_PORT_PB_DATA, port_pb_data_shadow, 7, val);
422 #endif
425 static __init void
426 cris_ide_init(void)
428 volatile unsigned int dummy;
430 *R_ATA_CTRL_DATA = 0;
431 *R_ATA_TRANSFER_CNT = 0;
432 *R_ATA_CONFIG = 0;
434 if (cris_request_io_interface(if_ata, "ETRAX100LX IDE")) {
435 printk(KERN_CRIT "ide: Failed to get IO interface\n");
436 return;
437 } else if (cris_request_dma(ATA_TX_DMA_NBR,
438 "ETRAX100LX IDE TX",
439 DMA_VERBOSE_ON_ERROR,
440 dma_ata)) {
441 cris_free_io_interface(if_ata);
442 printk(KERN_CRIT "ide: Failed to get Tx DMA channel\n");
443 return;
444 } else if (cris_request_dma(ATA_RX_DMA_NBR,
445 "ETRAX100LX IDE RX",
446 DMA_VERBOSE_ON_ERROR,
447 dma_ata)) {
448 cris_free_dma(ATA_TX_DMA_NBR, "ETRAX100LX IDE Tx");
449 cris_free_io_interface(if_ata);
450 printk(KERN_CRIT "ide: Failed to get Rx DMA channel\n");
451 return;
454 /* make a dummy read to set the ata controller in a proper state */
455 dummy = *R_ATA_STATUS_DATA;
457 *R_ATA_CONFIG = ( IO_FIELD( R_ATA_CONFIG, enable, 1 ));
458 *R_ATA_CTRL_DATA = ( IO_STATE( R_ATA_CTRL_DATA, rw, read) |
459 IO_FIELD( R_ATA_CTRL_DATA, addr, 1 ) );
461 while(*R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy)); /* wait for busy flag*/
463 *R_IRQ_MASK0_SET = ( IO_STATE( R_IRQ_MASK0_SET, ata_irq0, set ) |
464 IO_STATE( R_IRQ_MASK0_SET, ata_irq1, set ) |
465 IO_STATE( R_IRQ_MASK0_SET, ata_irq2, set ) |
466 IO_STATE( R_IRQ_MASK0_SET, ata_irq3, set ) );
468 /* reset the dma channels we will use */
470 RESET_DMA(ATA_TX_DMA_NBR);
471 RESET_DMA(ATA_RX_DMA_NBR);
472 WAIT_DMA(ATA_TX_DMA_NBR);
473 WAIT_DMA(ATA_RX_DMA_NBR);
476 #define cris_dma_descr_type etrax_dma_descr
477 #define cris_pio_read IO_STATE(R_ATA_CTRL_DATA, rw, read)
478 #define cris_ultra_mask 0x0
479 #define MAX_DESCR_SIZE 0x10000UL
481 static unsigned long
482 cris_ide_get_reg(unsigned long reg)
484 return (reg & 0x0e000000) >> 25;
487 static void
488 cris_ide_fill_descriptor(cris_dma_descr_type *d, void* buf, unsigned int len, int last)
490 d->buf = virt_to_phys(buf);
491 d->sw_len = len == MAX_DESCR_SIZE ? 0 : len;
492 if (last)
493 d->ctrl |= d_eol;
496 static void cris_ide_start_dma(ide_drive_t *drive, cris_dma_descr_type *d, int dir, int type, int len)
498 unsigned long cmd;
500 if (dir) {
501 /* need to do this before RX DMA due to a chip bug
502 * it is enough to just flush the part of the cache that
503 * corresponds to the buffers we start, but since HD transfers
504 * usually are more than 8 kB, it is easier to optimize for the
505 * normal case and just flush the entire cache. its the only
506 * way to be sure! (OB movie quote)
508 flush_etrax_cache();
509 *R_DMA_CH3_FIRST = virt_to_phys(d);
510 *R_DMA_CH3_CMD = IO_STATE(R_DMA_CH3_CMD, cmd, start);
512 } else {
513 *R_DMA_CH2_FIRST = virt_to_phys(d);
514 *R_DMA_CH2_CMD = IO_STATE(R_DMA_CH2_CMD, cmd, start);
517 /* initiate a multi word dma read using DMA handshaking */
519 *R_ATA_TRANSFER_CNT =
520 IO_FIELD(R_ATA_TRANSFER_CNT, count, len >> 1);
522 cmd = dir ? IO_STATE(R_ATA_CTRL_DATA, rw, read) : IO_STATE(R_ATA_CTRL_DATA, rw, write);
523 cmd |= type == TYPE_PIO ? IO_STATE(R_ATA_CTRL_DATA, handsh, pio) :
524 IO_STATE(R_ATA_CTRL_DATA, handsh, dma);
525 *R_ATA_CTRL_DATA =
526 cmd |
527 IO_FIELD(R_ATA_CTRL_DATA, data, IDE_DATA_REG) |
528 IO_STATE(R_ATA_CTRL_DATA, src_dst, dma) |
529 IO_STATE(R_ATA_CTRL_DATA, multi, on) |
530 IO_STATE(R_ATA_CTRL_DATA, dma_size, word);
533 static void
534 cris_ide_wait_dma(int dir)
536 if (dir)
537 WAIT_DMA(ATA_RX_DMA_NBR);
538 else
539 WAIT_DMA(ATA_TX_DMA_NBR);
542 static int cris_dma_test_irq(ide_drive_t *drive)
544 int intr = *R_IRQ_MASK0_RD;
545 int bus = IO_EXTRACT(R_ATA_CTRL_DATA, sel, IDE_DATA_REG);
546 return intr & (1 << (bus + IO_BITNR(R_IRQ_MASK0_RD, ata_irq0))) ? 1 : 0;
550 static void cris_ide_initialize_dma(int dir)
552 if (dir)
554 RESET_DMA(ATA_RX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */
555 WAIT_DMA(ATA_RX_DMA_NBR);
557 else
559 RESET_DMA(ATA_TX_DMA_NBR); /* sometimes the DMA channel get stuck so we need to do this */
560 WAIT_DMA(ATA_TX_DMA_NBR);
564 #endif
566 void
567 cris_ide_outw(unsigned short data, unsigned long reg) {
568 int timeleft;
570 LOWDB(printk("ow: data 0x%x, reg 0x%x\n", data, reg));
572 /* note the lack of handling any timeouts. we stop waiting, but we don't
573 * really notify anybody.
576 timeleft = IDE_REGISTER_TIMEOUT;
577 /* wait for busy flag */
578 do {
579 timeleft--;
580 } while(timeleft && cris_ide_busy());
583 * Fall through at a timeout, so the ongoing command will be
584 * aborted by the write below, which is expected to be a dummy
585 * command to the command register. This happens when a faulty
586 * drive times out on a command. See comment on timeout in
587 * INB.
589 if(!timeleft)
590 printk("ATA timeout reg 0x%lx := 0x%x\n", reg, data);
592 cris_ide_write_command(reg|data); /* write data to the drive's register */
594 timeleft = IDE_REGISTER_TIMEOUT;
595 /* wait for transmitter ready */
596 do {
597 timeleft--;
598 } while(timeleft && !cris_ide_ready());
601 void
602 cris_ide_outb(unsigned char data, unsigned long reg)
604 cris_ide_outw(data, reg);
607 void
608 cris_ide_outbsync(ide_drive_t *drive, u8 addr, unsigned long port)
610 cris_ide_outw(addr, port);
613 unsigned short
614 cris_ide_inw(unsigned long reg) {
615 int timeleft;
616 unsigned short val;
618 timeleft = IDE_REGISTER_TIMEOUT;
619 /* wait for busy flag */
620 do {
621 timeleft--;
622 } while(timeleft && cris_ide_busy());
624 if(!timeleft) {
626 * If we're asked to read the status register, like for
627 * example when a command does not complete for an
628 * extended time, but the ATA interface is stuck in a
629 * busy state at the *ETRAX* ATA interface level (as has
630 * happened repeatedly with at least one bad disk), then
631 * the best thing to do is to pretend that we read
632 * "busy" in the status register, so the IDE driver will
633 * time-out, abort the ongoing command and perform a
634 * reset sequence. Note that the subsequent OUT_BYTE
635 * call will also timeout on busy, but as long as the
636 * write is still performed, everything will be fine.
638 if (cris_ide_get_reg(reg) == IDE_STATUS_OFFSET)
639 return BUSY_STAT;
640 else
641 /* For other rare cases we assume 0 is good enough. */
642 return 0;
645 cris_ide_write_command(reg | cris_pio_read);
647 timeleft = IDE_REGISTER_TIMEOUT;
648 /* wait for available */
649 do {
650 timeleft--;
651 } while(timeleft && !cris_ide_data_available(&val));
653 if(!timeleft)
654 return 0;
656 LOWDB(printk("inb: 0x%x from reg 0x%x\n", val & 0xff, reg));
658 return val;
661 unsigned char
662 cris_ide_inb(unsigned long reg)
664 return (unsigned char)cris_ide_inw(reg);
667 static int cris_dma_end (ide_drive_t *drive);
668 static int cris_dma_setup (ide_drive_t *drive);
669 static void cris_dma_exec_cmd (ide_drive_t *drive, u8 command);
670 static int cris_dma_test_irq(ide_drive_t *drive);
671 static void cris_dma_start(ide_drive_t *drive);
672 static void cris_ide_input_data (ide_drive_t *drive, void *, unsigned int);
673 static void cris_ide_output_data (ide_drive_t *drive, void *, unsigned int);
674 static void cris_atapi_input_bytes(ide_drive_t *drive, void *, unsigned int);
675 static void cris_atapi_output_bytes(ide_drive_t *drive, void *, unsigned int);
676 static int cris_dma_on (ide_drive_t *drive);
678 static void cris_dma_off(ide_drive_t *drive)
682 static void cris_set_pio_mode(ide_drive_t *drive, const u8 pio)
684 int setup, strobe, hold;
686 switch(pio)
688 case 0:
689 setup = ATA_PIO0_SETUP;
690 strobe = ATA_PIO0_STROBE;
691 hold = ATA_PIO0_HOLD;
692 break;
693 case 1:
694 setup = ATA_PIO1_SETUP;
695 strobe = ATA_PIO1_STROBE;
696 hold = ATA_PIO1_HOLD;
697 break;
698 case 2:
699 setup = ATA_PIO2_SETUP;
700 strobe = ATA_PIO2_STROBE;
701 hold = ATA_PIO2_HOLD;
702 break;
703 case 3:
704 setup = ATA_PIO3_SETUP;
705 strobe = ATA_PIO3_STROBE;
706 hold = ATA_PIO3_HOLD;
707 break;
708 case 4:
709 setup = ATA_PIO4_SETUP;
710 strobe = ATA_PIO4_STROBE;
711 hold = ATA_PIO4_HOLD;
712 break;
713 default:
714 return;
717 cris_ide_set_speed(TYPE_PIO, setup, strobe, hold);
720 static void cris_set_dma_mode(ide_drive_t *drive, const u8 speed)
722 int cyc = 0, dvs = 0, strobe = 0, hold = 0;
724 switch(speed)
726 case XFER_UDMA_0:
727 cyc = ATA_UDMA0_CYC;
728 dvs = ATA_UDMA0_DVS;
729 break;
730 case XFER_UDMA_1:
731 cyc = ATA_UDMA1_CYC;
732 dvs = ATA_UDMA1_DVS;
733 break;
734 case XFER_UDMA_2:
735 cyc = ATA_UDMA2_CYC;
736 dvs = ATA_UDMA2_DVS;
737 break;
738 case XFER_MW_DMA_0:
739 strobe = ATA_DMA0_STROBE;
740 hold = ATA_DMA0_HOLD;
741 break;
742 case XFER_MW_DMA_1:
743 strobe = ATA_DMA1_STROBE;
744 hold = ATA_DMA1_HOLD;
745 break;
746 case XFER_MW_DMA_2:
747 strobe = ATA_DMA2_STROBE;
748 hold = ATA_DMA2_HOLD;
749 break;
750 default:
751 BUG();
752 break;
755 if (speed >= XFER_UDMA_0)
756 cris_ide_set_speed(TYPE_UDMA, cyc, dvs, 0);
757 else
758 cris_ide_set_speed(TYPE_DMA, 0, strobe, hold);
761 void __init
762 init_e100_ide (void)
764 hw_regs_t hw;
765 int ide_offsets[IDE_NR_PORTS];
766 int h;
767 int i;
769 printk("ide: ETRAX FS built-in ATA DMA controller\n");
771 for (i = IDE_DATA_OFFSET; i <= IDE_STATUS_OFFSET; i++)
772 ide_offsets[i] = cris_ide_reg_addr(i, 0, 1);
774 /* the IDE control register is at ATA address 6, with CS1 active instead of CS0 */
775 ide_offsets[IDE_CONTROL_OFFSET] = cris_ide_reg_addr(6, 1, 0);
777 /* first fill in some stuff in the ide_hwifs fields */
779 for(h = 0; h < MAX_HWIFS; h++) {
780 ide_hwif_t *hwif = &ide_hwifs[h];
781 ide_setup_ports(&hw, cris_ide_base_address(h),
782 ide_offsets,
783 0, 0, cris_ide_ack_intr,
784 ide_default_irq(0));
785 ide_register_hw(&hw, NULL, 1, &hwif);
786 hwif->mmio = 1;
787 hwif->chipset = ide_etrax100;
788 hwif->set_pio_mode = &cris_set_pio_mode;
789 hwif->set_dma_mode = &cris_set_dma_mode;
790 hwif->ata_input_data = &cris_ide_input_data;
791 hwif->ata_output_data = &cris_ide_output_data;
792 hwif->atapi_input_bytes = &cris_atapi_input_bytes;
793 hwif->atapi_output_bytes = &cris_atapi_output_bytes;
794 hwif->ide_dma_end = &cris_dma_end;
795 hwif->dma_setup = &cris_dma_setup;
796 hwif->dma_exec_cmd = &cris_dma_exec_cmd;
797 hwif->ide_dma_test_irq = &cris_dma_test_irq;
798 hwif->dma_start = &cris_dma_start;
799 hwif->OUTB = &cris_ide_outb;
800 hwif->OUTW = &cris_ide_outw;
801 hwif->OUTBSYNC = &cris_ide_outbsync;
802 hwif->INB = &cris_ide_inb;
803 hwif->INW = &cris_ide_inw;
804 hwif->dma_host_off = &cris_dma_off;
805 hwif->dma_host_on = &cris_dma_on;
806 hwif->dma_off_quietly = &cris_dma_off;
807 hwif->cbl = ATA_CBL_PATA40;
808 hwif->host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
809 hwif->pio_mask = ATA_PIO4,
810 hwif->drives[0].autotune = 1;
811 hwif->drives[1].autotune = 1;
812 hwif->ultra_mask = cris_ultra_mask;
813 hwif->mwdma_mask = 0x07; /* Multiword DMA 0-2 */
816 /* Reset pulse */
817 cris_ide_reset(0);
818 udelay(25);
819 cris_ide_reset(1);
821 cris_ide_init();
823 cris_ide_set_speed(TYPE_PIO, ATA_PIO4_SETUP, ATA_PIO4_STROBE, ATA_PIO4_HOLD);
824 cris_ide_set_speed(TYPE_DMA, 0, ATA_DMA2_STROBE, ATA_DMA2_HOLD);
825 cris_ide_set_speed(TYPE_UDMA, ATA_UDMA2_CYC, ATA_UDMA2_DVS, 0);
828 static int cris_dma_on (ide_drive_t *drive)
830 return 0;
834 static cris_dma_descr_type mydescr __attribute__ ((__aligned__(16)));
837 * The following routines are mainly used by the ATAPI drivers.
839 * These routines will round up any request for an odd number of bytes,
840 * so if an odd bytecount is specified, be sure that there's at least one
841 * extra byte allocated for the buffer.
843 static void
844 cris_atapi_input_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount)
846 D(printk("atapi_input_bytes, buffer 0x%x, count %d\n",
847 buffer, bytecount));
849 if(bytecount & 1) {
850 printk("warning, odd bytecount in cdrom_in_bytes = %d.\n", bytecount);
851 bytecount++; /* to round off */
854 /* setup DMA and start transfer */
856 cris_ide_fill_descriptor(&mydescr, buffer, bytecount, 1);
857 cris_ide_start_dma(drive, &mydescr, 1, TYPE_PIO, bytecount);
859 /* wait for completion */
860 LED_DISK_READ(1);
861 cris_ide_wait_dma(1);
862 LED_DISK_READ(0);
865 static void
866 cris_atapi_output_bytes (ide_drive_t *drive, void *buffer, unsigned int bytecount)
868 D(printk("atapi_output_bytes, buffer 0x%x, count %d\n",
869 buffer, bytecount));
871 if(bytecount & 1) {
872 printk("odd bytecount %d in atapi_out_bytes!\n", bytecount);
873 bytecount++;
876 cris_ide_fill_descriptor(&mydescr, buffer, bytecount, 1);
877 cris_ide_start_dma(drive, &mydescr, 0, TYPE_PIO, bytecount);
879 /* wait for completion */
881 LED_DISK_WRITE(1);
882 LED_DISK_READ(1);
883 cris_ide_wait_dma(0);
884 LED_DISK_WRITE(0);
888 * This is used for most PIO data transfers *from* the IDE interface
890 static void
891 cris_ide_input_data (ide_drive_t *drive, void *buffer, unsigned int wcount)
893 cris_atapi_input_bytes(drive, buffer, wcount << 2);
897 * This is used for most PIO data transfers *to* the IDE interface
899 static void
900 cris_ide_output_data (ide_drive_t *drive, void *buffer, unsigned int wcount)
902 cris_atapi_output_bytes(drive, buffer, wcount << 2);
905 /* we only have one DMA channel on the chip for ATA, so we can keep these statically */
906 static cris_dma_descr_type ata_descrs[MAX_DMA_DESCRS] __attribute__ ((__aligned__(16)));
907 static unsigned int ata_tot_size;
910 * cris_ide_build_dmatable() prepares a dma request.
911 * Returns 0 if all went okay, returns 1 otherwise.
913 static int cris_ide_build_dmatable (ide_drive_t *drive)
915 ide_hwif_t *hwif = drive->hwif;
916 struct scatterlist* sg;
917 struct request *rq = drive->hwif->hwgroup->rq;
918 unsigned long size, addr;
919 unsigned int count = 0;
920 int i = 0;
922 sg = hwif->sg_table;
924 ata_tot_size = 0;
926 ide_map_sg(drive, rq);
927 i = hwif->sg_nents;
929 while(i) {
931 * Determine addr and size of next buffer area. We assume that
932 * individual virtual buffers are always composed linearly in
933 * physical memory. For example, we assume that any 8kB buffer
934 * is always composed of two adjacent physical 4kB pages rather
935 * than two possibly non-adjacent physical 4kB pages.
937 /* group sequential buffers into one large buffer */
938 addr = sg_phys(sg);
939 size = sg_dma_len(sg);
940 while (--i) {
941 sg = sg_next(sg);
942 if ((addr + size) != sg_phys(sg))
943 break;
944 size += sg_dma_len(sg);
947 /* did we run out of descriptors? */
949 if(count >= MAX_DMA_DESCRS) {
950 printk("%s: too few DMA descriptors\n", drive->name);
951 return 1;
954 /* however, this case is more difficult - rw_trf_cnt cannot be more
955 than 65536 words per transfer, so in that case we need to either
956 1) use a DMA interrupt to re-trigger rw_trf_cnt and continue with
957 the descriptors, or
958 2) simply do the request here, and get dma_intr to only ide_end_request on
959 those blocks that were actually set-up for transfer.
962 if(ata_tot_size + size > 131072) {
963 printk("too large total ATA DMA request, %d + %d!\n", ata_tot_size, (int)size);
964 return 1;
967 /* If size > MAX_DESCR_SIZE it has to be splitted into new descriptors. Since we
968 don't handle size > 131072 only one split is necessary */
970 if(size > MAX_DESCR_SIZE) {
971 cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, MAX_DESCR_SIZE, 0);
972 count++;
973 ata_tot_size += MAX_DESCR_SIZE;
974 size -= MAX_DESCR_SIZE;
975 addr += MAX_DESCR_SIZE;
978 cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, size,i ? 0 : 1);
979 count++;
980 ata_tot_size += size;
983 if (count) {
984 /* return and say all is ok */
985 return 0;
988 printk("%s: empty DMA table?\n", drive->name);
989 return 1; /* let the PIO routines handle this weirdness */
993 * cris_dma_intr() is the handler for disk read/write DMA interrupts
995 static ide_startstop_t cris_dma_intr (ide_drive_t *drive)
997 LED_DISK_READ(0);
998 LED_DISK_WRITE(0);
1000 return ide_dma_intr(drive);
1004 * Functions below initiates/aborts DMA read/write operations on a drive.
1006 * The caller is assumed to have selected the drive and programmed the drive's
1007 * sector address using CHS or LBA. All that remains is to prepare for DMA
1008 * and then issue the actual read/write DMA/PIO command to the drive.
1010 * For ATAPI devices, we just prepare for DMA and return. The caller should
1011 * then issue the packet command to the drive and call us again with
1012 * cris_dma_start afterwards.
1014 * Returns 0 if all went well.
1015 * Returns 1 if DMA read/write could not be started, in which case
1016 * the caller should revert to PIO for the current request.
1019 static int cris_dma_end(ide_drive_t *drive)
1021 drive->waiting_for_dma = 0;
1022 return 0;
1025 static int cris_dma_setup(ide_drive_t *drive)
1027 struct request *rq = drive->hwif->hwgroup->rq;
1029 cris_ide_initialize_dma(!rq_data_dir(rq));
1030 if (cris_ide_build_dmatable (drive)) {
1031 ide_map_sg(drive, rq);
1032 return 1;
1035 drive->waiting_for_dma = 1;
1036 return 0;
1039 static void cris_dma_exec_cmd(ide_drive_t *drive, u8 command)
1041 /* set the irq handler which will finish the request when DMA is done */
1042 ide_set_handler(drive, &cris_dma_intr, WAIT_CMD, NULL);
1044 /* issue cmd to drive */
1045 cris_ide_outb(command, IDE_COMMAND_REG);
1048 static void cris_dma_start(ide_drive_t *drive)
1050 struct request *rq = drive->hwif->hwgroup->rq;
1051 int writing = rq_data_dir(rq);
1052 int type = TYPE_DMA;
1054 if (drive->current_speed >= XFER_UDMA_0)
1055 type = TYPE_UDMA;
1057 cris_ide_start_dma(drive, &ata_descrs[0], writing ? 0 : 1, type, ata_tot_size);
1059 if (writing) {
1060 LED_DISK_WRITE(1);
1061 } else {
1062 LED_DISK_READ(1);