2 * drivers/net/wan/dscc4/dscc4.c: a DSCC4 HDLC driver for Linux
4 * This software may be used and distributed according to the terms of the
5 * GNU General Public License.
7 * The author may be reached as romieu@cogenit.fr.
8 * Specific bug reports/asian food will be welcome.
10 * Special thanks to the nice people at CS-Telecom for the hardware and the
11 * access to the test/measure tools.
16 * I. Board Compatibility
18 * This device driver is designed for the Siemens PEB20534 4 ports serial
19 * controller as found on Etinc PCISYNC cards. The documentation for the
20 * chipset is available at http://www.infineon.com:
21 * - Data Sheet "DSCC4, DMA Supported Serial Communication Controller with
22 * 4 Channels, PEB 20534 Version 2.1, PEF 20534 Version 2.1";
23 * - Application Hint "Management of DSCC4 on-chip FIFO resources".
24 * - Errata sheet DS5 (courtesy of Michael Skerritt).
25 * Jens David has built an adapter based on the same chipset. Take a look
26 * at http://www.afthd.tu-darmstadt.de/~dg1kjd/pciscc4 for a specific
28 * Sample code (2 revisions) is available at Infineon.
30 * II. Board-specific settings
32 * Pcisync can transmit some clock signal to the outside world on the
33 * *first two* ports provided you put a quartz and a line driver on it and
34 * remove the jumpers. The operation is described on Etinc web site. If you
35 * go DCE on these ports, don't forget to use an adequate cable.
37 * Sharing of the PCI interrupt line for this board is possible.
39 * III. Driver operation
41 * The rx/tx operations are based on a linked list of descriptors. The driver
42 * doesn't use HOLD mode any more. HOLD mode is definitely buggy and the more
43 * I tried to fix it, the more it started to look like (convoluted) software
44 * mutation of LxDA method. Errata sheet DS5 suggests to use LxDA: consider
45 * this a rfc2119 MUST.
48 * When the tx ring is full, the xmit routine issues a call to netdev_stop.
49 * The device is supposed to be enabled again during an ALLS irq (we could
50 * use HI but as it's easy to lose events, it's fscked).
53 * The received frames aren't supposed to span over multiple receiving areas.
54 * I may implement it some day but it isn't the highest ranked item.
57 * The current error (XDU, RFO) recovery code is untested.
58 * So far, RDO takes his RX channel down and the right sequence to enable it
59 * again is still a mistery. If RDO happens, plan a reboot. More details
60 * in the code (NB: as this happens, TX still works).
61 * Don't mess the cables during operation, especially on DTE ports. I don't
62 * suggest it for DCE either but at least one can get some messages instead
63 * of a complete instant freeze.
64 * Tests are done on Rev. 20 of the silicium. The RDO handling changes with
65 * the documentation/chipset releases.
69 * - use polling at high irq/s,
70 * - performance analysis,
73 * 2001/12/10 Daniela Squassoni <daniela@cyclades.com>
74 * - Contribution to support the new generic HDLC layer.
77 * - old style interface removal
78 * - dscc4_release_ring fix (related to DMA mapping)
79 * - hard_start_xmit fix (hint: TxSizeMax)
83 #include <linux/module.h>
84 #include <linux/types.h>
85 #include <linux/errno.h>
86 #include <linux/list.h>
87 #include <linux/ioport.h>
88 #include <linux/pci.h>
89 #include <linux/kernel.h>
92 #include <asm/system.h>
93 #include <asm/cache.h>
94 #include <asm/byteorder.h>
95 #include <asm/uaccess.h>
99 #include <linux/init.h>
100 #include <linux/string.h>
102 #include <linux/if_arp.h>
103 #include <linux/netdevice.h>
104 #include <linux/skbuff.h>
105 #include <linux/delay.h>
106 #include <net/syncppp.h>
107 #include <linux/hdlc.h>
108 #include <linux/mutex.h>
111 static const char version
[] = "$Id: dscc4.c,v 1.173 2003/09/20 23:55:34 romieu Exp $ for Linux\n";
115 #ifdef CONFIG_DSCC4_PCI_RST
116 static DEFINE_MUTEX(dscc4_mutex
);
117 static u32 dscc4_pci_config_store
[16];
120 #define DRV_NAME "dscc4"
124 /* Module parameters */
126 MODULE_AUTHOR("Maintainer: Francois Romieu <romieu@cogenit.fr>");
127 MODULE_DESCRIPTION("Siemens PEB20534 PCI Controler");
128 MODULE_LICENSE("GPL");
129 module_param(debug
, int, 0);
130 MODULE_PARM_DESC(debug
,"Enable/disable extra messages");
131 module_param(quartz
, int, 0);
132 MODULE_PARM_DESC(quartz
,"If present, on-board quartz frequency (Hz)");
146 u32 jiffies
; /* Allows sizeof(TxFD) == sizeof(RxFD) + extra hack */
157 #define DUMMY_SKB_SIZE 64
159 #define TX_RING_SIZE 32
160 #define RX_RING_SIZE 32
161 #define TX_TOTAL_SIZE TX_RING_SIZE*sizeof(struct TxFD)
162 #define RX_TOTAL_SIZE RX_RING_SIZE*sizeof(struct RxFD)
163 #define IRQ_RING_SIZE 64 /* Keep it a multiple of 32 */
164 #define TX_TIMEOUT (HZ/10)
165 #define DSCC4_HZ_MAX 33000000
166 #define BRR_DIVIDER_MAX 64*0x00004000 /* Cf errata DS5 p.10 */
167 #define dev_per_card 4
168 #define SCC_REGISTERS_MAX 23 /* Cf errata DS5 p.4 */
170 #define SOURCE_ID(flags) (((flags) >> 28) & 0x03)
171 #define TO_SIZE(state) (((state) >> 16) & 0x1fff)
174 * Given the operating range of Linux HDLC, the 2 defines below could be
175 * made simpler. However they are a fine reminder for the limitations of
176 * the driver: it's better to stay < TxSizeMax and < RxSizeMax.
178 #define TO_STATE_TX(len) cpu_to_le32(((len) & TxSizeMax) << 16)
179 #define TO_STATE_RX(len) cpu_to_le32((RX_MAX(len) % RxSizeMax) << 16)
180 #define RX_MAX(len) ((((len) >> 5) + 1) << 5) /* Cf RLCR */
181 #define SCC_REG_START(dpriv) (SCC_START+(dpriv->dev_id)*SCC_OFFSET)
183 struct dscc4_pci_priv
{
187 struct pci_dev
*pdev
;
189 struct dscc4_dev_priv
*root
;
190 dma_addr_t iqcfg_dma
;
194 struct dscc4_dev_priv
{
195 struct sk_buff
*rx_skbuff
[RX_RING_SIZE
];
196 struct sk_buff
*tx_skbuff
[TX_RING_SIZE
];
203 /* FIXME: check all the volatile are required */
204 volatile u32 tx_current
;
209 volatile u32 tx_dirty
;
214 dma_addr_t tx_fd_dma
;
215 dma_addr_t rx_fd_dma
;
219 u32 scc_regs
[SCC_REGISTERS_MAX
]; /* Cf errata DS5 p.4 */
221 struct timer_list timer
;
223 struct dscc4_pci_priv
*pci_priv
;
230 unsigned short encoding
;
231 unsigned short parity
;
232 struct net_device
*dev
;
233 sync_serial_settings settings
;
234 void __iomem
*base_addr
;
235 u32 __pad
__attribute__ ((aligned (4)));
238 /* GLOBAL registers definitions */
259 /* SCC registers definitions */
260 #define SCC_START 0x0100
261 #define SCC_OFFSET 0x80
273 #define GPDATA 0x0404
277 #define EncodingMask 0x00700000
278 #define CrcMask 0x00000003
280 #define IntRxScc0 0x10000000
281 #define IntTxScc0 0x01000000
283 #define TxPollCmd 0x00000400
284 #define RxActivate 0x08000000
285 #define MTFi 0x04000000
286 #define Rdr 0x00400000
287 #define Rdt 0x00200000
288 #define Idr 0x00100000
289 #define Idt 0x00080000
290 #define TxSccRes 0x01000000
291 #define RxSccRes 0x00010000
292 #define TxSizeMax 0x1fff /* Datasheet DS1 - 11.1.1.1 */
293 #define RxSizeMax 0x1ffc /* Datasheet DS1 - 11.1.2.1 */
295 #define Ccr0ClockMask 0x0000003f
296 #define Ccr1LoopMask 0x00000200
297 #define IsrMask 0x000fffff
298 #define BrrExpMask 0x00000f00
299 #define BrrMultMask 0x0000003f
300 #define EncodingMask 0x00700000
301 #define Hold 0x40000000
302 #define SccBusy 0x10000000
303 #define PowerUp 0x80000000
304 #define Vis 0x00001000
305 #define FrameOk (FrameVfr | FrameCrc)
306 #define FrameVfr 0x80
307 #define FrameRdo 0x40
308 #define FrameCrc 0x20
309 #define FrameRab 0x10
310 #define FrameAborted 0x00000200
311 #define FrameEnd 0x80000000
312 #define DataComplete 0x40000000
313 #define LengthCheck 0x00008000
314 #define SccEvt 0x02000000
315 #define NoAck 0x00000200
316 #define Action 0x00000001
317 #define HiDesc 0x20000000
320 #define RxEvt 0xf0000000
321 #define TxEvt 0x0f000000
322 #define Alls 0x00040000
323 #define Xdu 0x00010000
324 #define Cts 0x00004000
325 #define Xmr 0x00002000
326 #define Xpr 0x00001000
327 #define Rdo 0x00000080
328 #define Rfs 0x00000040
329 #define Cd 0x00000004
330 #define Rfo 0x00000002
331 #define Flex 0x00000001
333 /* DMA core events */
334 #define Cfg 0x00200000
335 #define Hi 0x00040000
336 #define Fi 0x00020000
337 #define Err 0x00010000
338 #define Arf 0x00000002
339 #define ArAck 0x00000001
342 #define Ready 0x00000000
343 #define NeedIDR 0x00000001
344 #define NeedIDT 0x00000002
345 #define RdoSet 0x00000004
346 #define FakeReset 0x00000008
348 /* Don't mask RDO. Ever. */
350 #define EventsMask 0xfffeef7f
352 #define EventsMask 0xfffa8f7a
355 /* Functions prototypes */
356 static void dscc4_rx_irq(struct dscc4_pci_priv
*, struct dscc4_dev_priv
*);
357 static void dscc4_tx_irq(struct dscc4_pci_priv
*, struct dscc4_dev_priv
*);
358 static int dscc4_found1(struct pci_dev
*, void __iomem
*ioaddr
);
359 static int dscc4_init_one(struct pci_dev
*, const struct pci_device_id
*ent
);
360 static int dscc4_open(struct net_device
*);
361 static int dscc4_start_xmit(struct sk_buff
*, struct net_device
*);
362 static int dscc4_close(struct net_device
*);
363 static int dscc4_ioctl(struct net_device
*dev
, struct ifreq
*rq
, int cmd
);
364 static int dscc4_init_ring(struct net_device
*);
365 static void dscc4_release_ring(struct dscc4_dev_priv
*);
366 static void dscc4_timer(unsigned long);
367 static void dscc4_tx_timeout(struct net_device
*);
368 static irqreturn_t
dscc4_irq(int irq
, void *dev_id
);
369 static int dscc4_hdlc_attach(struct net_device
*, unsigned short, unsigned short);
370 static int dscc4_set_iface(struct dscc4_dev_priv
*, struct net_device
*);
372 static int dscc4_tx_poll(struct dscc4_dev_priv
*, struct net_device
*);
375 static inline struct dscc4_dev_priv
*dscc4_priv(struct net_device
*dev
)
377 return dev_to_hdlc(dev
)->priv
;
380 static inline struct net_device
*dscc4_to_dev(struct dscc4_dev_priv
*p
)
385 static void scc_patchl(u32 mask
, u32 value
, struct dscc4_dev_priv
*dpriv
,
386 struct net_device
*dev
, int offset
)
390 /* Cf scc_writel for concern regarding thread-safety */
391 state
= dpriv
->scc_regs
[offset
>> 2];
394 dpriv
->scc_regs
[offset
>> 2] = state
;
395 writel(state
, dpriv
->base_addr
+ SCC_REG_START(dpriv
) + offset
);
398 static void scc_writel(u32 bits
, struct dscc4_dev_priv
*dpriv
,
399 struct net_device
*dev
, int offset
)
403 * As of 2002/02/16, there are no thread racing for access.
405 dpriv
->scc_regs
[offset
>> 2] = bits
;
406 writel(bits
, dpriv
->base_addr
+ SCC_REG_START(dpriv
) + offset
);
409 static inline u32
scc_readl(struct dscc4_dev_priv
*dpriv
, int offset
)
411 return dpriv
->scc_regs
[offset
>> 2];
414 static u32
scc_readl_star(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
416 /* Cf errata DS5 p.4 */
417 readl(dpriv
->base_addr
+ SCC_REG_START(dpriv
) + STAR
);
418 return readl(dpriv
->base_addr
+ SCC_REG_START(dpriv
) + STAR
);
421 static inline void dscc4_do_tx(struct dscc4_dev_priv
*dpriv
,
422 struct net_device
*dev
)
424 dpriv
->ltda
= dpriv
->tx_fd_dma
+
425 ((dpriv
->tx_current
-1)%TX_RING_SIZE
)*sizeof(struct TxFD
);
426 writel(dpriv
->ltda
, dpriv
->base_addr
+ CH0LTDA
+ dpriv
->dev_id
*4);
427 /* Flush posted writes *NOW* */
428 readl(dpriv
->base_addr
+ CH0LTDA
+ dpriv
->dev_id
*4);
431 static inline void dscc4_rx_update(struct dscc4_dev_priv
*dpriv
,
432 struct net_device
*dev
)
434 dpriv
->lrda
= dpriv
->rx_fd_dma
+
435 ((dpriv
->rx_dirty
- 1)%RX_RING_SIZE
)*sizeof(struct RxFD
);
436 writel(dpriv
->lrda
, dpriv
->base_addr
+ CH0LRDA
+ dpriv
->dev_id
*4);
439 static inline unsigned int dscc4_tx_done(struct dscc4_dev_priv
*dpriv
)
441 return dpriv
->tx_current
== dpriv
->tx_dirty
;
444 static inline unsigned int dscc4_tx_quiescent(struct dscc4_dev_priv
*dpriv
,
445 struct net_device
*dev
)
447 return readl(dpriv
->base_addr
+ CH0FTDA
+ dpriv
->dev_id
*4) == dpriv
->ltda
;
450 static int state_check(u32 state
, struct dscc4_dev_priv
*dpriv
,
451 struct net_device
*dev
, const char *msg
)
456 if (SOURCE_ID(state
) != dpriv
->dev_id
) {
457 printk(KERN_DEBUG
"%s (%s): Source Id=%d, state=%08x\n",
458 dev
->name
, msg
, SOURCE_ID(state
), state
);
461 if (state
& 0x0df80c00) {
462 printk(KERN_DEBUG
"%s (%s): state=%08x (UFO alert)\n",
463 dev
->name
, msg
, state
);
470 static void dscc4_tx_print(struct net_device
*dev
,
471 struct dscc4_dev_priv
*dpriv
,
474 printk(KERN_DEBUG
"%s: tx_current=%02d tx_dirty=%02d (%s)\n",
475 dev
->name
, dpriv
->tx_current
, dpriv
->tx_dirty
, msg
);
478 static void dscc4_release_ring(struct dscc4_dev_priv
*dpriv
)
480 struct pci_dev
*pdev
= dpriv
->pci_priv
->pdev
;
481 struct TxFD
*tx_fd
= dpriv
->tx_fd
;
482 struct RxFD
*rx_fd
= dpriv
->rx_fd
;
483 struct sk_buff
**skbuff
;
486 pci_free_consistent(pdev
, TX_TOTAL_SIZE
, tx_fd
, dpriv
->tx_fd_dma
);
487 pci_free_consistent(pdev
, RX_TOTAL_SIZE
, rx_fd
, dpriv
->rx_fd_dma
);
489 skbuff
= dpriv
->tx_skbuff
;
490 for (i
= 0; i
< TX_RING_SIZE
; i
++) {
492 pci_unmap_single(pdev
, tx_fd
->data
, (*skbuff
)->len
,
494 dev_kfree_skb(*skbuff
);
500 skbuff
= dpriv
->rx_skbuff
;
501 for (i
= 0; i
< RX_RING_SIZE
; i
++) {
503 pci_unmap_single(pdev
, rx_fd
->data
,
504 RX_MAX(HDLC_MAX_MRU
), PCI_DMA_FROMDEVICE
);
505 dev_kfree_skb(*skbuff
);
512 static inline int try_get_rx_skb(struct dscc4_dev_priv
*dpriv
,
513 struct net_device
*dev
)
515 unsigned int dirty
= dpriv
->rx_dirty
%RX_RING_SIZE
;
516 struct RxFD
*rx_fd
= dpriv
->rx_fd
+ dirty
;
517 const int len
= RX_MAX(HDLC_MAX_MRU
);
521 skb
= dev_alloc_skb(len
);
522 dpriv
->rx_skbuff
[dirty
] = skb
;
524 skb
->protocol
= hdlc_type_trans(skb
, dev
);
525 rx_fd
->data
= pci_map_single(dpriv
->pci_priv
->pdev
, skb
->data
,
526 len
, PCI_DMA_FROMDEVICE
);
528 rx_fd
->data
= (u32
) NULL
;
535 * IRQ/thread/whatever safe
537 static int dscc4_wait_ack_cec(struct dscc4_dev_priv
*dpriv
,
538 struct net_device
*dev
, char *msg
)
543 if (!(scc_readl_star(dpriv
, dev
) & SccBusy
)) {
544 printk(KERN_DEBUG
"%s: %s ack (%d try)\n", dev
->name
,
548 schedule_timeout_uninterruptible(10);
551 printk(KERN_ERR
"%s: %s timeout\n", dev
->name
, msg
);
553 return (i
>= 0) ? i
: -EAGAIN
;
556 static int dscc4_do_action(struct net_device
*dev
, char *msg
)
558 void __iomem
*ioaddr
= dscc4_priv(dev
)->base_addr
;
561 writel(Action
, ioaddr
+ GCMDR
);
564 u32 state
= readl(ioaddr
);
567 printk(KERN_DEBUG
"%s: %s ack\n", dev
->name
, msg
);
568 writel(ArAck
, ioaddr
);
570 } else if (state
& Arf
) {
571 printk(KERN_ERR
"%s: %s failed\n", dev
->name
, msg
);
578 printk(KERN_ERR
"%s: %s timeout\n", dev
->name
, msg
);
583 static inline int dscc4_xpr_ack(struct dscc4_dev_priv
*dpriv
)
585 int cur
= dpriv
->iqtx_current
%IRQ_RING_SIZE
;
589 if (!(dpriv
->flags
& (NeedIDR
| NeedIDT
)) ||
590 (dpriv
->iqtx
[cur
] & Xpr
))
593 schedule_timeout_uninterruptible(10);
596 return (i
>= 0 ) ? i
: -EAGAIN
;
599 #if 0 /* dscc4_{rx/tx}_reset are both unreliable - more tweak needed */
600 static void dscc4_rx_reset(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
604 spin_lock_irqsave(&dpriv
->pci_priv
->lock
, flags
);
605 /* Cf errata DS5 p.6 */
606 writel(0x00000000, dpriv
->base_addr
+ CH0LRDA
+ dpriv
->dev_id
*4);
607 scc_patchl(PowerUp
, 0, dpriv
, dev
, CCR0
);
608 readl(dpriv
->base_addr
+ CH0LRDA
+ dpriv
->dev_id
*4);
609 writel(MTFi
|Rdr
, dpriv
->base_addr
+ dpriv
->dev_id
*0x0c + CH0CFG
);
610 writel(Action
, dpriv
->base_addr
+ GCMDR
);
611 spin_unlock_irqrestore(&dpriv
->pci_priv
->lock
, flags
);
617 static void dscc4_tx_reset(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
621 /* Cf errata DS5 p.7 */
622 scc_patchl(PowerUp
, 0, dpriv
, dev
, CCR0
);
623 scc_writel(0x00050000, dpriv
, dev
, CCR2
);
625 * Must be longer than the time required to fill the fifo.
627 while (!dscc4_tx_quiescent(dpriv
, dev
) && ++i
) {
632 writel(MTFi
|Rdt
, dpriv
->base_addr
+ dpriv
->dev_id
*0x0c + CH0CFG
);
633 if (dscc4_do_action(dev
, "Rdt") < 0)
634 printk(KERN_ERR
"%s: Tx reset failed\n", dev
->name
);
638 /* TODO: (ab)use this function to refill a completely depleted RX ring. */
639 static inline void dscc4_rx_skb(struct dscc4_dev_priv
*dpriv
,
640 struct net_device
*dev
)
642 struct RxFD
*rx_fd
= dpriv
->rx_fd
+ dpriv
->rx_current
%RX_RING_SIZE
;
643 struct net_device_stats
*stats
= hdlc_stats(dev
);
644 struct pci_dev
*pdev
= dpriv
->pci_priv
->pdev
;
648 skb
= dpriv
->rx_skbuff
[dpriv
->rx_current
++%RX_RING_SIZE
];
650 printk(KERN_DEBUG
"%s: skb=0 (%s)\n", dev
->name
, __FUNCTION__
);
653 pkt_len
= TO_SIZE(rx_fd
->state2
);
654 pci_unmap_single(pdev
, rx_fd
->data
, RX_MAX(HDLC_MAX_MRU
), PCI_DMA_FROMDEVICE
);
655 if ((skb
->data
[--pkt_len
] & FrameOk
) == FrameOk
) {
657 stats
->rx_bytes
+= pkt_len
;
658 skb_put(skb
, pkt_len
);
659 if (netif_running(dev
))
660 skb
->protocol
= hdlc_type_trans(skb
, dev
);
661 skb
->dev
->last_rx
= jiffies
;
664 if (skb
->data
[pkt_len
] & FrameRdo
)
665 stats
->rx_fifo_errors
++;
666 else if (!(skb
->data
[pkt_len
] | ~FrameCrc
))
667 stats
->rx_crc_errors
++;
668 else if (!(skb
->data
[pkt_len
] | ~(FrameVfr
| FrameRab
)))
669 stats
->rx_length_errors
++;
672 dev_kfree_skb_irq(skb
);
675 while ((dpriv
->rx_dirty
- dpriv
->rx_current
) % RX_RING_SIZE
) {
676 if (try_get_rx_skb(dpriv
, dev
) < 0)
680 dscc4_rx_update(dpriv
, dev
);
681 rx_fd
->state2
= 0x00000000;
682 rx_fd
->end
= 0xbabeface;
685 static void dscc4_free1(struct pci_dev
*pdev
)
687 struct dscc4_pci_priv
*ppriv
;
688 struct dscc4_dev_priv
*root
;
691 ppriv
= pci_get_drvdata(pdev
);
694 for (i
= 0; i
< dev_per_card
; i
++)
695 unregister_hdlc_device(dscc4_to_dev(root
+ i
));
697 pci_set_drvdata(pdev
, NULL
);
699 for (i
= 0; i
< dev_per_card
; i
++)
700 free_netdev(root
[i
].dev
);
705 static int __devinit
dscc4_init_one(struct pci_dev
*pdev
,
706 const struct pci_device_id
*ent
)
708 struct dscc4_pci_priv
*priv
;
709 struct dscc4_dev_priv
*dpriv
;
710 void __iomem
*ioaddr
;
713 printk(KERN_DEBUG
"%s", version
);
715 rc
= pci_enable_device(pdev
);
719 rc
= pci_request_region(pdev
, 0, "registers");
721 printk(KERN_ERR
"%s: can't reserve MMIO region (regs)\n",
725 rc
= pci_request_region(pdev
, 1, "LBI interface");
727 printk(KERN_ERR
"%s: can't reserve MMIO region (lbi)\n",
729 goto err_free_mmio_region_1
;
732 ioaddr
= ioremap(pci_resource_start(pdev
, 0),
733 pci_resource_len(pdev
, 0));
735 printk(KERN_ERR
"%s: cannot remap MMIO region %llx @ %llx\n",
736 DRV_NAME
, (unsigned long long)pci_resource_len(pdev
, 0),
737 (unsigned long long)pci_resource_start(pdev
, 0));
739 goto err_free_mmio_regions_2
;
741 printk(KERN_DEBUG
"Siemens DSCC4, MMIO at %#llx (regs), %#llx (lbi), IRQ %d\n",
742 (unsigned long long)pci_resource_start(pdev
, 0),
743 (unsigned long long)pci_resource_start(pdev
, 1), pdev
->irq
);
745 /* Cf errata DS5 p.2 */
746 pci_write_config_byte(pdev
, PCI_LATENCY_TIMER
, 0xf8);
747 pci_set_master(pdev
);
749 rc
= dscc4_found1(pdev
, ioaddr
);
753 priv
= pci_get_drvdata(pdev
);
755 rc
= request_irq(pdev
->irq
, dscc4_irq
, IRQF_SHARED
, DRV_NAME
, priv
->root
);
757 printk(KERN_WARNING
"%s: IRQ %d busy\n", DRV_NAME
, pdev
->irq
);
761 /* power up/little endian/dma core controlled via lrda/ltda */
762 writel(0x00000001, ioaddr
+ GMODE
);
763 /* Shared interrupt queue */
767 bits
= (IRQ_RING_SIZE
>> 5) - 1;
771 writel(bits
, ioaddr
+ IQLENR0
);
773 /* Global interrupt queue */
774 writel((u32
)(((IRQ_RING_SIZE
>> 5) - 1) << 20), ioaddr
+ IQLENR1
);
775 priv
->iqcfg
= (u32
*) pci_alloc_consistent(pdev
,
776 IRQ_RING_SIZE
*sizeof(u32
), &priv
->iqcfg_dma
);
779 writel(priv
->iqcfg_dma
, ioaddr
+ IQCFG
);
784 * SCC 0-3 private rx/tx irq structures
785 * IQRX/TXi needs to be set soon. Learned it the hard way...
787 for (i
= 0; i
< dev_per_card
; i
++) {
788 dpriv
= priv
->root
+ i
;
789 dpriv
->iqtx
= (u32
*) pci_alloc_consistent(pdev
,
790 IRQ_RING_SIZE
*sizeof(u32
), &dpriv
->iqtx_dma
);
792 goto err_free_iqtx_6
;
793 writel(dpriv
->iqtx_dma
, ioaddr
+ IQTX0
+ i
*4);
795 for (i
= 0; i
< dev_per_card
; i
++) {
796 dpriv
= priv
->root
+ i
;
797 dpriv
->iqrx
= (u32
*) pci_alloc_consistent(pdev
,
798 IRQ_RING_SIZE
*sizeof(u32
), &dpriv
->iqrx_dma
);
800 goto err_free_iqrx_7
;
801 writel(dpriv
->iqrx_dma
, ioaddr
+ IQRX0
+ i
*4);
804 /* Cf application hint. Beware of hard-lock condition on threshold. */
805 writel(0x42104000, ioaddr
+ FIFOCR1
);
806 //writel(0x9ce69800, ioaddr + FIFOCR2);
807 writel(0xdef6d800, ioaddr
+ FIFOCR2
);
808 //writel(0x11111111, ioaddr + FIFOCR4);
809 writel(0x18181818, ioaddr
+ FIFOCR4
);
810 // FIXME: should depend on the chipset revision
811 writel(0x0000000e, ioaddr
+ FIFOCR3
);
813 writel(0xff200001, ioaddr
+ GCMDR
);
821 dpriv
= priv
->root
+ i
;
822 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
823 dpriv
->iqrx
, dpriv
->iqrx_dma
);
828 dpriv
= priv
->root
+ i
;
829 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
830 dpriv
->iqtx
, dpriv
->iqtx_dma
);
832 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
), priv
->iqcfg
,
835 free_irq(pdev
->irq
, priv
->root
);
840 err_free_mmio_regions_2
:
841 pci_release_region(pdev
, 1);
842 err_free_mmio_region_1
:
843 pci_release_region(pdev
, 0);
845 pci_disable_device(pdev
);
850 * Let's hope the default values are decent enough to protect my
851 * feet from the user's gun - Ueimor
853 static void dscc4_init_registers(struct dscc4_dev_priv
*dpriv
,
854 struct net_device
*dev
)
856 /* No interrupts, SCC core disabled. Let's relax */
857 scc_writel(0x00000000, dpriv
, dev
, CCR0
);
859 scc_writel(LengthCheck
| (HDLC_MAX_MRU
>> 5), dpriv
, dev
, RLCR
);
862 * No address recognition/crc-CCITT/cts enabled
863 * Shared flags transmission disabled - cf errata DS5 p.11
864 * Carrier detect disabled - cf errata p.14
865 * FIXME: carrier detection/polarity may be handled more gracefully.
867 scc_writel(0x02408000, dpriv
, dev
, CCR1
);
869 /* crc not forwarded - Cf errata DS5 p.11 */
870 scc_writel(0x00050008 & ~RxActivate
, dpriv
, dev
, CCR2
);
872 //scc_writel(0x00250008 & ~RxActivate, dpriv, dev, CCR2);
875 static inline int dscc4_set_quartz(struct dscc4_dev_priv
*dpriv
, int hz
)
879 if ((hz
< 0) || (hz
> DSCC4_HZ_MAX
))
882 dpriv
->pci_priv
->xtal_hz
= hz
;
887 static int dscc4_found1(struct pci_dev
*pdev
, void __iomem
*ioaddr
)
889 struct dscc4_pci_priv
*ppriv
;
890 struct dscc4_dev_priv
*root
;
891 int i
, ret
= -ENOMEM
;
893 root
= kcalloc(dev_per_card
, sizeof(*root
), GFP_KERNEL
);
895 printk(KERN_ERR
"%s: can't allocate data\n", DRV_NAME
);
899 for (i
= 0; i
< dev_per_card
; i
++) {
900 root
[i
].dev
= alloc_hdlcdev(root
+ i
);
905 ppriv
= kzalloc(sizeof(*ppriv
), GFP_KERNEL
);
907 printk(KERN_ERR
"%s: can't allocate private data\n", DRV_NAME
);
912 spin_lock_init(&ppriv
->lock
);
914 for (i
= 0; i
< dev_per_card
; i
++) {
915 struct dscc4_dev_priv
*dpriv
= root
+ i
;
916 struct net_device
*d
= dscc4_to_dev(dpriv
);
917 hdlc_device
*hdlc
= dev_to_hdlc(d
);
919 d
->base_addr
= (unsigned long)ioaddr
;
922 d
->open
= dscc4_open
;
923 d
->stop
= dscc4_close
;
924 d
->set_multicast_list
= NULL
;
925 d
->do_ioctl
= dscc4_ioctl
;
926 d
->tx_timeout
= dscc4_tx_timeout
;
927 d
->watchdog_timeo
= TX_TIMEOUT
;
928 SET_NETDEV_DEV(d
, &pdev
->dev
);
931 dpriv
->pci_priv
= ppriv
;
932 dpriv
->base_addr
= ioaddr
;
933 spin_lock_init(&dpriv
->lock
);
935 hdlc
->xmit
= dscc4_start_xmit
;
936 hdlc
->attach
= dscc4_hdlc_attach
;
938 dscc4_init_registers(dpriv
, d
);
939 dpriv
->parity
= PARITY_CRC16_PR0_CCITT
;
940 dpriv
->encoding
= ENCODING_NRZ
;
942 ret
= dscc4_init_ring(d
);
946 ret
= register_hdlc_device(d
);
948 printk(KERN_ERR
"%s: unable to register\n", DRV_NAME
);
949 dscc4_release_ring(dpriv
);
954 ret
= dscc4_set_quartz(root
, quartz
);
958 pci_set_drvdata(pdev
, ppriv
);
963 dscc4_release_ring(root
+ i
);
964 unregister_hdlc_device(dscc4_to_dev(root
+ i
));
970 free_netdev(root
[i
].dev
);
976 /* FIXME: get rid of the unneeded code */
977 static void dscc4_timer(unsigned long data
)
979 struct net_device
*dev
= (struct net_device
*)data
;
980 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
981 // struct dscc4_pci_priv *ppriv;
985 dpriv
->timer
.expires
= jiffies
+ TX_TIMEOUT
;
986 add_timer(&dpriv
->timer
);
989 static void dscc4_tx_timeout(struct net_device
*dev
)
991 /* FIXME: something is missing there */
994 static int dscc4_loopback_check(struct dscc4_dev_priv
*dpriv
)
996 sync_serial_settings
*settings
= &dpriv
->settings
;
998 if (settings
->loopback
&& (settings
->clock_type
!= CLOCK_INT
)) {
999 struct net_device
*dev
= dscc4_to_dev(dpriv
);
1001 printk(KERN_INFO
"%s: loopback requires clock\n", dev
->name
);
1007 #ifdef CONFIG_DSCC4_PCI_RST
1009 * Some DSCC4-based cards wires the GPIO port and the PCI #RST pin together
1010 * so as to provide a safe way to reset the asic while not the whole machine
1013 * This code doesn't need to be efficient. Keep It Simple
1015 static void dscc4_pci_reset(struct pci_dev
*pdev
, void __iomem
*ioaddr
)
1019 mutex_lock(&dscc4_mutex
);
1020 for (i
= 0; i
< 16; i
++)
1021 pci_read_config_dword(pdev
, i
<< 2, dscc4_pci_config_store
+ i
);
1023 /* Maximal LBI clock divider (who cares ?) and whole GPIO range. */
1024 writel(0x001c0000, ioaddr
+ GMODE
);
1025 /* Configure GPIO port as output */
1026 writel(0x0000ffff, ioaddr
+ GPDIR
);
1027 /* Disable interruption */
1028 writel(0x0000ffff, ioaddr
+ GPIM
);
1030 writel(0x0000ffff, ioaddr
+ GPDATA
);
1031 writel(0x00000000, ioaddr
+ GPDATA
);
1033 /* Flush posted writes */
1034 readl(ioaddr
+ GSTAR
);
1036 schedule_timeout_uninterruptible(10);
1038 for (i
= 0; i
< 16; i
++)
1039 pci_write_config_dword(pdev
, i
<< 2, dscc4_pci_config_store
[i
]);
1040 mutex_unlock(&dscc4_mutex
);
1043 #define dscc4_pci_reset(pdev,ioaddr) do {} while (0)
1044 #endif /* CONFIG_DSCC4_PCI_RST */
1046 static int dscc4_open(struct net_device
*dev
)
1048 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1049 struct dscc4_pci_priv
*ppriv
;
1052 if ((dscc4_loopback_check(dpriv
) < 0) || !dev
->hard_start_xmit
)
1055 if ((ret
= hdlc_open(dev
)))
1058 ppriv
= dpriv
->pci_priv
;
1061 * Due to various bugs, there is no way to reliably reset a
1062 * specific port (manufacturer's dependant special PCI #RST wiring
1063 * apart: it affects all ports). Thus the device goes in the best
1064 * silent mode possible at dscc4_close() time and simply claims to
1065 * be up if it's opened again. It still isn't possible to change
1066 * the HDLC configuration without rebooting but at least the ports
1067 * can be up/down ifconfig'ed without killing the host.
1069 if (dpriv
->flags
& FakeReset
) {
1070 dpriv
->flags
&= ~FakeReset
;
1071 scc_patchl(0, PowerUp
, dpriv
, dev
, CCR0
);
1072 scc_patchl(0, 0x00050000, dpriv
, dev
, CCR2
);
1073 scc_writel(EventsMask
, dpriv
, dev
, IMR
);
1074 printk(KERN_INFO
"%s: up again.\n", dev
->name
);
1078 /* IDT+IDR during XPR */
1079 dpriv
->flags
= NeedIDR
| NeedIDT
;
1081 scc_patchl(0, PowerUp
| Vis
, dpriv
, dev
, CCR0
);
1084 * The following is a bit paranoid...
1086 * NB: the datasheet "...CEC will stay active if the SCC is in
1087 * power-down mode or..." and CCR2.RAC = 1 are two different
1090 if (scc_readl_star(dpriv
, dev
) & SccBusy
) {
1091 printk(KERN_ERR
"%s busy. Try later\n", dev
->name
);
1095 printk(KERN_INFO
"%s: available. Good\n", dev
->name
);
1097 scc_writel(EventsMask
, dpriv
, dev
, IMR
);
1099 /* Posted write is flushed in the wait_ack loop */
1100 scc_writel(TxSccRes
| RxSccRes
, dpriv
, dev
, CMDR
);
1102 if ((ret
= dscc4_wait_ack_cec(dpriv
, dev
, "Cec")) < 0)
1103 goto err_disable_scc_events
;
1106 * I would expect XPR near CE completion (before ? after ?).
1107 * At worst, this code won't see a late XPR and people
1108 * will have to re-issue an ifconfig (this is harmless).
1109 * WARNING, a really missing XPR usually means a hardware
1110 * reset is needed. Suggestions anyone ?
1112 if ((ret
= dscc4_xpr_ack(dpriv
)) < 0) {
1113 printk(KERN_ERR
"%s: %s timeout\n", DRV_NAME
, "XPR");
1114 goto err_disable_scc_events
;
1118 dscc4_tx_print(dev
, dpriv
, "Open");
1121 netif_start_queue(dev
);
1123 init_timer(&dpriv
->timer
);
1124 dpriv
->timer
.expires
= jiffies
+ 10*HZ
;
1125 dpriv
->timer
.data
= (unsigned long)dev
;
1126 dpriv
->timer
.function
= &dscc4_timer
;
1127 add_timer(&dpriv
->timer
);
1128 netif_carrier_on(dev
);
1132 err_disable_scc_events
:
1133 scc_writel(0xffffffff, dpriv
, dev
, IMR
);
1134 scc_patchl(PowerUp
| Vis
, 0, dpriv
, dev
, CCR0
);
1141 #ifdef DSCC4_POLLING
1142 static int dscc4_tx_poll(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
1144 /* FIXME: it's gonna be easy (TM), for sure */
1146 #endif /* DSCC4_POLLING */
1148 static int dscc4_start_xmit(struct sk_buff
*skb
, struct net_device
*dev
)
1150 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1151 struct dscc4_pci_priv
*ppriv
= dpriv
->pci_priv
;
1155 next
= dpriv
->tx_current
%TX_RING_SIZE
;
1156 dpriv
->tx_skbuff
[next
] = skb
;
1157 tx_fd
= dpriv
->tx_fd
+ next
;
1158 tx_fd
->state
= FrameEnd
| TO_STATE_TX(skb
->len
);
1159 tx_fd
->data
= pci_map_single(ppriv
->pdev
, skb
->data
, skb
->len
,
1161 tx_fd
->complete
= 0x00000000;
1162 tx_fd
->jiffies
= jiffies
;
1165 #ifdef DSCC4_POLLING
1166 spin_lock(&dpriv
->lock
);
1167 while (dscc4_tx_poll(dpriv
, dev
));
1168 spin_unlock(&dpriv
->lock
);
1171 dev
->trans_start
= jiffies
;
1174 dscc4_tx_print(dev
, dpriv
, "Xmit");
1175 /* To be cleaned(unsigned int)/optimized. Later, ok ? */
1176 if (!((++dpriv
->tx_current
- dpriv
->tx_dirty
)%TX_RING_SIZE
))
1177 netif_stop_queue(dev
);
1179 if (dscc4_tx_quiescent(dpriv
, dev
))
1180 dscc4_do_tx(dpriv
, dev
);
1185 static int dscc4_close(struct net_device
*dev
)
1187 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1189 del_timer_sync(&dpriv
->timer
);
1190 netif_stop_queue(dev
);
1192 scc_patchl(PowerUp
| Vis
, 0, dpriv
, dev
, CCR0
);
1193 scc_patchl(0x00050000, 0, dpriv
, dev
, CCR2
);
1194 scc_writel(0xffffffff, dpriv
, dev
, IMR
);
1196 dpriv
->flags
|= FakeReset
;
1203 static inline int dscc4_check_clock_ability(int port
)
1207 #ifdef CONFIG_DSCC4_PCISYNC
1215 * DS1 p.137: "There are a total of 13 different clocking modes..."
1218 * - by default, assume a clock is provided on pin RxClk/TxClk (clock mode 0a).
1219 * Clock mode 3b _should_ work but the testing seems to make this point
1220 * dubious (DIY testing requires setting CCR0 at 0x00000033).
1221 * This is supposed to provide least surprise "DTE like" behavior.
1222 * - if line rate is specified, clocks are assumed to be locally generated.
1223 * A quartz must be available (on pin XTAL1). Modes 6b/7b are used. Choosing
1224 * between these it automagically done according on the required frequency
1225 * scaling. Of course some rounding may take place.
1226 * - no high speed mode (40Mb/s). May be trivial to do but I don't have an
1227 * appropriate external clocking device for testing.
1228 * - no time-slot/clock mode 5: shameless lazyness.
1230 * The clock signals wiring can be (is ?) manufacturer dependant. Good luck.
1232 * BIG FAT WARNING: if the device isn't provided enough clocking signal, it
1233 * won't pass the init sequence. For example, straight back-to-back DTE without
1234 * external clock will fail when dscc4_open() (<- 'ifconfig hdlcx xxx') is
1237 * Typos lurk in datasheet (missing divier in clock mode 7a figure 51 p.153
1240 * Clock mode related bits of CCR0:
1241 * +------------ TOE: output TxClk (0b/2b/3a/3b/6b/7a/7b only)
1242 * | +---------- SSEL: sub-mode select 0 -> a, 1 -> b
1243 * | | +-------- High Speed: say 0
1244 * | | | +-+-+-- Clock Mode: 0..7
1247 * x|x|5|4|3|2|1|0| lower bits
1249 * Division factor of BRR: k = (N+1)x2^M (total divider = 16xk in mode 6b)
1250 * +-+-+-+------------------ M (0..15)
1251 * | | | | +-+-+-+-+-+-- N (0..63)
1252 * 0 0 0 0 | | | | 0 0 | | | | | |
1253 * ...-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
1254 * f|e|d|c|b|a|9|8|7|6|5|4|3|2|1|0| lower bits
1257 static int dscc4_set_clock(struct net_device
*dev
, u32
*bps
, u32
*state
)
1259 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1263 *state
&= ~Ccr0ClockMask
;
1264 if (*bps
) { /* Clock generated - required for DCE */
1265 u32 n
= 0, m
= 0, divider
;
1268 xtal
= dpriv
->pci_priv
->xtal_hz
;
1271 if (dscc4_check_clock_ability(dpriv
->dev_id
) < 0)
1273 divider
= xtal
/ *bps
;
1274 if (divider
> BRR_DIVIDER_MAX
) {
1276 *state
|= 0x00000036; /* Clock mode 6b (BRG/16) */
1278 *state
|= 0x00000037; /* Clock mode 7b (BRG) */
1279 if (divider
>> 22) {
1282 } else if (divider
) {
1283 /* Extraction of the 6 highest weighted bits */
1285 while (0xffffffc0 & divider
) {
1293 if (!(*state
& 0x00000001)) /* ?b mode mask => clock mode 6b */
1295 *bps
= xtal
/ divider
;
1298 * External clock - DTE
1299 * "state" already reflects Clock mode 0a (CCR0 = 0xzzzzzz00).
1300 * Nothing more to be done
1304 scc_writel(brr
, dpriv
, dev
, BRR
);
1310 static int dscc4_ioctl(struct net_device
*dev
, struct ifreq
*ifr
, int cmd
)
1312 sync_serial_settings __user
*line
= ifr
->ifr_settings
.ifs_ifsu
.sync
;
1313 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1314 const size_t size
= sizeof(dpriv
->settings
);
1317 if (dev
->flags
& IFF_UP
)
1320 if (cmd
!= SIOCWANDEV
)
1323 switch(ifr
->ifr_settings
.type
) {
1325 ifr
->ifr_settings
.type
= IF_IFACE_SYNC_SERIAL
;
1326 if (ifr
->ifr_settings
.size
< size
) {
1327 ifr
->ifr_settings
.size
= size
; /* data size wanted */
1330 if (copy_to_user(line
, &dpriv
->settings
, size
))
1334 case IF_IFACE_SYNC_SERIAL
:
1335 if (!capable(CAP_NET_ADMIN
))
1338 if (dpriv
->flags
& FakeReset
) {
1339 printk(KERN_INFO
"%s: please reset the device"
1340 " before this command\n", dev
->name
);
1343 if (copy_from_user(&dpriv
->settings
, line
, size
))
1345 ret
= dscc4_set_iface(dpriv
, dev
);
1349 ret
= hdlc_ioctl(dev
, ifr
, cmd
);
1356 static int dscc4_match(struct thingie
*p
, int value
)
1360 for (i
= 0; p
[i
].define
!= -1; i
++) {
1361 if (value
== p
[i
].define
)
1364 if (p
[i
].define
== -1)
1370 static int dscc4_clock_setting(struct dscc4_dev_priv
*dpriv
,
1371 struct net_device
*dev
)
1373 sync_serial_settings
*settings
= &dpriv
->settings
;
1374 int ret
= -EOPNOTSUPP
;
1377 bps
= settings
->clock_rate
;
1378 state
= scc_readl(dpriv
, CCR0
);
1379 if (dscc4_set_clock(dev
, &bps
, &state
) < 0)
1381 if (bps
) { /* DCE */
1382 printk(KERN_DEBUG
"%s: generated RxClk (DCE)\n", dev
->name
);
1383 if (settings
->clock_rate
!= bps
) {
1384 printk(KERN_DEBUG
"%s: clock adjusted (%08d -> %08d)\n",
1385 dev
->name
, settings
->clock_rate
, bps
);
1386 settings
->clock_rate
= bps
;
1389 state
|= PowerUp
| Vis
;
1390 printk(KERN_DEBUG
"%s: external RxClk (DTE)\n", dev
->name
);
1392 scc_writel(state
, dpriv
, dev
, CCR0
);
1398 static int dscc4_encoding_setting(struct dscc4_dev_priv
*dpriv
,
1399 struct net_device
*dev
)
1401 struct thingie encoding
[] = {
1402 { ENCODING_NRZ
, 0x00000000 },
1403 { ENCODING_NRZI
, 0x00200000 },
1404 { ENCODING_FM_MARK
, 0x00400000 },
1405 { ENCODING_FM_SPACE
, 0x00500000 },
1406 { ENCODING_MANCHESTER
, 0x00600000 },
1411 i
= dscc4_match(encoding
, dpriv
->encoding
);
1413 scc_patchl(EncodingMask
, encoding
[i
].bits
, dpriv
, dev
, CCR0
);
1419 static int dscc4_loopback_setting(struct dscc4_dev_priv
*dpriv
,
1420 struct net_device
*dev
)
1422 sync_serial_settings
*settings
= &dpriv
->settings
;
1425 state
= scc_readl(dpriv
, CCR1
);
1426 if (settings
->loopback
) {
1427 printk(KERN_DEBUG
"%s: loopback\n", dev
->name
);
1428 state
|= 0x00000100;
1430 printk(KERN_DEBUG
"%s: normal\n", dev
->name
);
1431 state
&= ~0x00000100;
1433 scc_writel(state
, dpriv
, dev
, CCR1
);
1437 static int dscc4_crc_setting(struct dscc4_dev_priv
*dpriv
,
1438 struct net_device
*dev
)
1440 struct thingie crc
[] = {
1441 { PARITY_CRC16_PR0_CCITT
, 0x00000010 },
1442 { PARITY_CRC16_PR1_CCITT
, 0x00000000 },
1443 { PARITY_CRC32_PR0_CCITT
, 0x00000011 },
1444 { PARITY_CRC32_PR1_CCITT
, 0x00000001 }
1448 i
= dscc4_match(crc
, dpriv
->parity
);
1450 scc_patchl(CrcMask
, crc
[i
].bits
, dpriv
, dev
, CCR1
);
1456 static int dscc4_set_iface(struct dscc4_dev_priv
*dpriv
, struct net_device
*dev
)
1459 int (*action
)(struct dscc4_dev_priv
*, struct net_device
*);
1460 } *p
, do_setting
[] = {
1461 { dscc4_encoding_setting
},
1462 { dscc4_clock_setting
},
1463 { dscc4_loopback_setting
},
1464 { dscc4_crc_setting
},
1469 for (p
= do_setting
; p
->action
; p
++) {
1470 if ((ret
= p
->action(dpriv
, dev
)) < 0)
1476 static irqreturn_t
dscc4_irq(int irq
, void *token
)
1478 struct dscc4_dev_priv
*root
= token
;
1479 struct dscc4_pci_priv
*priv
;
1480 struct net_device
*dev
;
1481 void __iomem
*ioaddr
;
1483 unsigned long flags
;
1486 priv
= root
->pci_priv
;
1487 dev
= dscc4_to_dev(root
);
1489 spin_lock_irqsave(&priv
->lock
, flags
);
1491 ioaddr
= root
->base_addr
;
1493 state
= readl(ioaddr
+ GSTAR
);
1499 printk(KERN_DEBUG
"%s: GSTAR = 0x%08x\n", DRV_NAME
, state
);
1500 writel(state
, ioaddr
+ GSTAR
);
1503 printk(KERN_ERR
"%s: failure (Arf). Harass the maintener\n",
1510 printk(KERN_DEBUG
"%s: CfgIV\n", DRV_NAME
);
1511 if (priv
->iqcfg
[priv
->cfg_cur
++%IRQ_RING_SIZE
] & Arf
)
1512 printk(KERN_ERR
"%s: %s failed\n", dev
->name
, "CFG");
1513 if (!(state
&= ~Cfg
))
1516 if (state
& RxEvt
) {
1517 i
= dev_per_card
- 1;
1519 dscc4_rx_irq(priv
, root
+ i
);
1523 if (state
& TxEvt
) {
1524 i
= dev_per_card
- 1;
1526 dscc4_tx_irq(priv
, root
+ i
);
1531 spin_unlock_irqrestore(&priv
->lock
, flags
);
1532 return IRQ_RETVAL(handled
);
1535 static void dscc4_tx_irq(struct dscc4_pci_priv
*ppriv
,
1536 struct dscc4_dev_priv
*dpriv
)
1538 struct net_device
*dev
= dscc4_to_dev(dpriv
);
1543 cur
= dpriv
->iqtx_current
%IRQ_RING_SIZE
;
1544 state
= dpriv
->iqtx
[cur
];
1547 printk(KERN_DEBUG
"%s: Tx ISR = 0x%08x\n", dev
->name
,
1549 if ((debug
> 1) && (loop
> 1))
1550 printk(KERN_DEBUG
"%s: Tx irq loop=%d\n", dev
->name
, loop
);
1551 if (loop
&& netif_queue_stopped(dev
))
1552 if ((dpriv
->tx_current
- dpriv
->tx_dirty
)%TX_RING_SIZE
)
1553 netif_wake_queue(dev
);
1555 if (netif_running(dev
) && dscc4_tx_quiescent(dpriv
, dev
) &&
1556 !dscc4_tx_done(dpriv
))
1557 dscc4_do_tx(dpriv
, dev
);
1561 dpriv
->iqtx
[cur
] = 0;
1562 dpriv
->iqtx_current
++;
1564 if (state_check(state
, dpriv
, dev
, "Tx") < 0)
1567 if (state
& SccEvt
) {
1569 struct net_device_stats
*stats
= hdlc_stats(dev
);
1570 struct sk_buff
*skb
;
1574 dscc4_tx_print(dev
, dpriv
, "Alls");
1576 * DataComplete can't be trusted for Tx completion.
1579 cur
= dpriv
->tx_dirty
%TX_RING_SIZE
;
1580 tx_fd
= dpriv
->tx_fd
+ cur
;
1581 skb
= dpriv
->tx_skbuff
[cur
];
1583 pci_unmap_single(ppriv
->pdev
, tx_fd
->data
,
1584 skb
->len
, PCI_DMA_TODEVICE
);
1585 if (tx_fd
->state
& FrameEnd
) {
1586 stats
->tx_packets
++;
1587 stats
->tx_bytes
+= skb
->len
;
1589 dev_kfree_skb_irq(skb
);
1590 dpriv
->tx_skbuff
[cur
] = NULL
;
1594 printk(KERN_ERR
"%s Tx: NULL skb %d\n",
1598 * If the driver ends sending crap on the wire, it
1599 * will be way easier to diagnose than the (not so)
1600 * random freeze induced by null sized tx frames.
1602 tx_fd
->data
= tx_fd
->next
;
1603 tx_fd
->state
= FrameEnd
| TO_STATE_TX(2*DUMMY_SKB_SIZE
);
1604 tx_fd
->complete
= 0x00000000;
1607 if (!(state
&= ~Alls
))
1611 * Transmit Data Underrun
1614 printk(KERN_ERR
"%s: XDU. Ask maintainer\n", DRV_NAME
);
1615 dpriv
->flags
= NeedIDT
;
1618 dpriv
->base_addr
+ 0x0c*dpriv
->dev_id
+ CH0CFG
);
1619 writel(Action
, dpriv
->base_addr
+ GCMDR
);
1623 printk(KERN_INFO
"%s: CTS transition\n", dev
->name
);
1624 if (!(state
&= ~Cts
)) /* DEBUG */
1628 /* Frame needs to be sent again - FIXME */
1629 printk(KERN_ERR
"%s: Xmr. Ask maintainer\n", DRV_NAME
);
1630 if (!(state
&= ~Xmr
)) /* DEBUG */
1634 void __iomem
*scc_addr
;
1639 * - the busy condition happens (sometimes);
1640 * - it doesn't seem to make the handler unreliable.
1642 for (i
= 1; i
; i
<<= 1) {
1643 if (!(scc_readl_star(dpriv
, dev
) & SccBusy
))
1647 printk(KERN_INFO
"%s busy in irq\n", dev
->name
);
1649 scc_addr
= dpriv
->base_addr
+ 0x0c*dpriv
->dev_id
;
1650 /* Keep this order: IDT before IDR */
1651 if (dpriv
->flags
& NeedIDT
) {
1653 dscc4_tx_print(dev
, dpriv
, "Xpr");
1654 ring
= dpriv
->tx_fd_dma
+
1655 (dpriv
->tx_dirty
%TX_RING_SIZE
)*
1656 sizeof(struct TxFD
);
1657 writel(ring
, scc_addr
+ CH0BTDA
);
1658 dscc4_do_tx(dpriv
, dev
);
1659 writel(MTFi
| Idt
, scc_addr
+ CH0CFG
);
1660 if (dscc4_do_action(dev
, "IDT") < 0)
1662 dpriv
->flags
&= ~NeedIDT
;
1664 if (dpriv
->flags
& NeedIDR
) {
1665 ring
= dpriv
->rx_fd_dma
+
1666 (dpriv
->rx_current
%RX_RING_SIZE
)*
1667 sizeof(struct RxFD
);
1668 writel(ring
, scc_addr
+ CH0BRDA
);
1669 dscc4_rx_update(dpriv
, dev
);
1670 writel(MTFi
| Idr
, scc_addr
+ CH0CFG
);
1671 if (dscc4_do_action(dev
, "IDR") < 0)
1673 dpriv
->flags
&= ~NeedIDR
;
1675 /* Activate receiver and misc */
1676 scc_writel(0x08050008, dpriv
, dev
, CCR2
);
1679 if (!(state
&= ~Xpr
))
1684 printk(KERN_INFO
"%s: CD transition\n", dev
->name
);
1685 if (!(state
&= ~Cd
)) /* DEBUG */
1688 } else { /* ! SccEvt */
1690 #ifdef DSCC4_POLLING
1691 while (!dscc4_tx_poll(dpriv
, dev
));
1693 printk(KERN_INFO
"%s: Tx Hi\n", dev
->name
);
1697 printk(KERN_INFO
"%s: Tx ERR\n", dev
->name
);
1698 hdlc_stats(dev
)->tx_errors
++;
1705 static void dscc4_rx_irq(struct dscc4_pci_priv
*priv
,
1706 struct dscc4_dev_priv
*dpriv
)
1708 struct net_device
*dev
= dscc4_to_dev(dpriv
);
1713 cur
= dpriv
->iqrx_current
%IRQ_RING_SIZE
;
1714 state
= dpriv
->iqrx
[cur
];
1717 dpriv
->iqrx
[cur
] = 0;
1718 dpriv
->iqrx_current
++;
1720 if (state_check(state
, dpriv
, dev
, "Rx") < 0)
1723 if (!(state
& SccEvt
)){
1727 printk(KERN_DEBUG
"%s: Rx ISR = 0x%08x\n", dev
->name
,
1729 state
&= 0x00ffffff;
1730 if (state
& Err
) { /* Hold or reset */
1731 printk(KERN_DEBUG
"%s: Rx ERR\n", dev
->name
);
1732 cur
= dpriv
->rx_current
%RX_RING_SIZE
;
1733 rx_fd
= dpriv
->rx_fd
+ cur
;
1735 * Presume we're not facing a DMAC receiver reset.
1736 * As We use the rx size-filtering feature of the
1737 * DSCC4, the beginning of a new frame is waiting in
1738 * the rx fifo. I bet a Receive Data Overflow will
1739 * happen most of time but let's try and avoid it.
1740 * Btw (as for RDO) if one experiences ERR whereas
1741 * the system looks rather idle, there may be a
1742 * problem with latency. In this case, increasing
1743 * RX_RING_SIZE may help.
1745 //while (dpriv->rx_needs_refill) {
1746 while (!(rx_fd
->state1
& Hold
)) {
1749 if (!(cur
= cur
%RX_RING_SIZE
))
1750 rx_fd
= dpriv
->rx_fd
;
1752 //dpriv->rx_needs_refill--;
1753 try_get_rx_skb(dpriv
, dev
);
1756 rx_fd
->state1
&= ~Hold
;
1757 rx_fd
->state2
= 0x00000000;
1758 rx_fd
->end
= 0xbabeface;
1763 dscc4_rx_skb(dpriv
, dev
);
1766 if (state
& Hi
) { /* HI bit */
1767 printk(KERN_INFO
"%s: Rx Hi\n", dev
->name
);
1771 } else { /* SccEvt */
1773 //FIXME: verifier la presence de tous les evenements
1776 const char *irq_name
;
1778 { 0x00008000, "TIN"},
1779 { 0x00000020, "RSC"},
1780 { 0x00000010, "PCE"},
1781 { 0x00000008, "PLLA"},
1785 for (evt
= evts
; evt
->irq_name
; evt
++) {
1786 if (state
& evt
->mask
) {
1787 printk(KERN_DEBUG
"%s: %s\n",
1788 dev
->name
, evt
->irq_name
);
1789 if (!(state
&= ~evt
->mask
))
1794 if (!(state
&= ~0x0000c03c))
1798 printk(KERN_INFO
"%s: CTS transition\n", dev
->name
);
1799 if (!(state
&= ~Cts
)) /* DEBUG */
1803 * Receive Data Overflow (FIXME: fscked)
1807 void __iomem
*scc_addr
;
1811 // dscc4_rx_dump(dpriv);
1812 scc_addr
= dpriv
->base_addr
+ 0x0c*dpriv
->dev_id
;
1814 scc_patchl(RxActivate
, 0, dpriv
, dev
, CCR2
);
1816 * This has no effect. Why ?
1817 * ORed with TxSccRes, one sees the CFG ack (for
1818 * the TX part only).
1820 scc_writel(RxSccRes
, dpriv
, dev
, CMDR
);
1821 dpriv
->flags
|= RdoSet
;
1824 * Let's try and save something in the received data.
1825 * rx_current must be incremented at least once to
1826 * avoid HOLD in the BRDA-to-be-pointed desc.
1829 cur
= dpriv
->rx_current
++%RX_RING_SIZE
;
1830 rx_fd
= dpriv
->rx_fd
+ cur
;
1831 if (!(rx_fd
->state2
& DataComplete
))
1833 if (rx_fd
->state2
& FrameAborted
) {
1834 hdlc_stats(dev
)->rx_over_errors
++;
1835 rx_fd
->state1
|= Hold
;
1836 rx_fd
->state2
= 0x00000000;
1837 rx_fd
->end
= 0xbabeface;
1839 dscc4_rx_skb(dpriv
, dev
);
1843 if (dpriv
->flags
& RdoSet
)
1845 "%s: no RDO in Rx data\n", DRV_NAME
);
1847 #ifdef DSCC4_RDO_EXPERIMENTAL_RECOVERY
1849 * FIXME: must the reset be this violent ?
1851 #warning "FIXME: CH0BRDA"
1852 writel(dpriv
->rx_fd_dma
+
1853 (dpriv
->rx_current
%RX_RING_SIZE
)*
1854 sizeof(struct RxFD
), scc_addr
+ CH0BRDA
);
1855 writel(MTFi
|Rdr
|Idr
, scc_addr
+ CH0CFG
);
1856 if (dscc4_do_action(dev
, "RDR") < 0) {
1857 printk(KERN_ERR
"%s: RDO recovery failed(%s)\n",
1861 writel(MTFi
|Idr
, scc_addr
+ CH0CFG
);
1862 if (dscc4_do_action(dev
, "IDR") < 0) {
1863 printk(KERN_ERR
"%s: RDO recovery failed(%s)\n",
1869 scc_patchl(0, RxActivate
, dpriv
, dev
, CCR2
);
1873 printk(KERN_INFO
"%s: CD transition\n", dev
->name
);
1874 if (!(state
&= ~Cd
)) /* DEBUG */
1878 printk(KERN_DEBUG
"%s: Flex. Ttttt...\n", DRV_NAME
);
1879 if (!(state
&= ~Flex
))
1886 * I had expected the following to work for the first descriptor
1887 * (tx_fd->state = 0xc0000000)
1888 * - Hold=1 (don't try and branch to the next descripto);
1889 * - No=0 (I want an empty data section, i.e. size=0);
1890 * - Fe=1 (required by No=0 or we got an Err irq and must reset).
1891 * It failed and locked solid. Thus the introduction of a dummy skb.
1892 * Problem is acknowledged in errata sheet DS5. Joy :o/
1894 static struct sk_buff
*dscc4_init_dummy_skb(struct dscc4_dev_priv
*dpriv
)
1896 struct sk_buff
*skb
;
1898 skb
= dev_alloc_skb(DUMMY_SKB_SIZE
);
1900 int last
= dpriv
->tx_dirty
%TX_RING_SIZE
;
1901 struct TxFD
*tx_fd
= dpriv
->tx_fd
+ last
;
1903 skb
->len
= DUMMY_SKB_SIZE
;
1904 skb_copy_to_linear_data(skb
, version
,
1905 strlen(version
) % DUMMY_SKB_SIZE
);
1906 tx_fd
->state
= FrameEnd
| TO_STATE_TX(DUMMY_SKB_SIZE
);
1907 tx_fd
->data
= pci_map_single(dpriv
->pci_priv
->pdev
, skb
->data
,
1908 DUMMY_SKB_SIZE
, PCI_DMA_TODEVICE
);
1909 dpriv
->tx_skbuff
[last
] = skb
;
1914 static int dscc4_init_ring(struct net_device
*dev
)
1916 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
1917 struct pci_dev
*pdev
= dpriv
->pci_priv
->pdev
;
1923 ring
= pci_alloc_consistent(pdev
, RX_TOTAL_SIZE
, &dpriv
->rx_fd_dma
);
1926 dpriv
->rx_fd
= rx_fd
= (struct RxFD
*) ring
;
1928 ring
= pci_alloc_consistent(pdev
, TX_TOTAL_SIZE
, &dpriv
->tx_fd_dma
);
1930 goto err_free_dma_rx
;
1931 dpriv
->tx_fd
= tx_fd
= (struct TxFD
*) ring
;
1933 memset(dpriv
->tx_skbuff
, 0, sizeof(struct sk_buff
*)*TX_RING_SIZE
);
1934 dpriv
->tx_dirty
= 0xffffffff;
1935 i
= dpriv
->tx_current
= 0;
1937 tx_fd
->state
= FrameEnd
| TO_STATE_TX(2*DUMMY_SKB_SIZE
);
1938 tx_fd
->complete
= 0x00000000;
1939 /* FIXME: NULL should be ok - to be tried */
1940 tx_fd
->data
= dpriv
->tx_fd_dma
;
1941 (tx_fd
++)->next
= (u32
)(dpriv
->tx_fd_dma
+
1942 (++i
%TX_RING_SIZE
)*sizeof(*tx_fd
));
1943 } while (i
< TX_RING_SIZE
);
1945 if (!dscc4_init_dummy_skb(dpriv
))
1946 goto err_free_dma_tx
;
1948 memset(dpriv
->rx_skbuff
, 0, sizeof(struct sk_buff
*)*RX_RING_SIZE
);
1949 i
= dpriv
->rx_dirty
= dpriv
->rx_current
= 0;
1951 /* size set by the host. Multiple of 4 bytes please */
1952 rx_fd
->state1
= HiDesc
;
1953 rx_fd
->state2
= 0x00000000;
1954 rx_fd
->end
= 0xbabeface;
1955 rx_fd
->state1
|= TO_STATE_RX(HDLC_MAX_MRU
);
1956 // FIXME: return value verifiee mais traitement suspect
1957 if (try_get_rx_skb(dpriv
, dev
) >= 0)
1959 (rx_fd
++)->next
= (u32
)(dpriv
->rx_fd_dma
+
1960 (++i
%RX_RING_SIZE
)*sizeof(*rx_fd
));
1961 } while (i
< RX_RING_SIZE
);
1966 pci_free_consistent(pdev
, TX_TOTAL_SIZE
, ring
, dpriv
->tx_fd_dma
);
1968 pci_free_consistent(pdev
, RX_TOTAL_SIZE
, rx_fd
, dpriv
->rx_fd_dma
);
1973 static void __devexit
dscc4_remove_one(struct pci_dev
*pdev
)
1975 struct dscc4_pci_priv
*ppriv
;
1976 struct dscc4_dev_priv
*root
;
1977 void __iomem
*ioaddr
;
1980 ppriv
= pci_get_drvdata(pdev
);
1983 ioaddr
= root
->base_addr
;
1985 dscc4_pci_reset(pdev
, ioaddr
);
1987 free_irq(pdev
->irq
, root
);
1988 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
), ppriv
->iqcfg
,
1990 for (i
= 0; i
< dev_per_card
; i
++) {
1991 struct dscc4_dev_priv
*dpriv
= root
+ i
;
1993 dscc4_release_ring(dpriv
);
1994 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
1995 dpriv
->iqrx
, dpriv
->iqrx_dma
);
1996 pci_free_consistent(pdev
, IRQ_RING_SIZE
*sizeof(u32
),
1997 dpriv
->iqtx
, dpriv
->iqtx_dma
);
2004 pci_release_region(pdev
, 1);
2005 pci_release_region(pdev
, 0);
2007 pci_disable_device(pdev
);
2010 static int dscc4_hdlc_attach(struct net_device
*dev
, unsigned short encoding
,
2011 unsigned short parity
)
2013 struct dscc4_dev_priv
*dpriv
= dscc4_priv(dev
);
2015 if (encoding
!= ENCODING_NRZ
&&
2016 encoding
!= ENCODING_NRZI
&&
2017 encoding
!= ENCODING_FM_MARK
&&
2018 encoding
!= ENCODING_FM_SPACE
&&
2019 encoding
!= ENCODING_MANCHESTER
)
2022 if (parity
!= PARITY_NONE
&&
2023 parity
!= PARITY_CRC16_PR0_CCITT
&&
2024 parity
!= PARITY_CRC16_PR1_CCITT
&&
2025 parity
!= PARITY_CRC32_PR0_CCITT
&&
2026 parity
!= PARITY_CRC32_PR1_CCITT
)
2029 dpriv
->encoding
= encoding
;
2030 dpriv
->parity
= parity
;
2035 static int __init
dscc4_setup(char *str
)
2037 int *args
[] = { &debug
, &quartz
, NULL
}, **p
= args
;
2039 while (*p
&& (get_option(&str
, *p
) == 2))
2044 __setup("dscc4.setup=", dscc4_setup
);
2047 static struct pci_device_id dscc4_pci_tbl
[] = {
2048 { PCI_VENDOR_ID_SIEMENS
, PCI_DEVICE_ID_SIEMENS_DSCC4
,
2049 PCI_ANY_ID
, PCI_ANY_ID
, },
2052 MODULE_DEVICE_TABLE(pci
, dscc4_pci_tbl
);
2054 static struct pci_driver dscc4_driver
= {
2056 .id_table
= dscc4_pci_tbl
,
2057 .probe
= dscc4_init_one
,
2058 .remove
= __devexit_p(dscc4_remove_one
),
2061 static int __init
dscc4_init_module(void)
2063 return pci_register_driver(&dscc4_driver
);
2066 static void __exit
dscc4_cleanup_module(void)
2068 pci_unregister_driver(&dscc4_driver
);
2071 module_init(dscc4_init_module
);
2072 module_exit(dscc4_cleanup_module
);