include/linux/serial_reg.h

   1 /*
   2  * include/linux/serial_reg.h
   3  *
   4  * Copyright (C) 1992, 1994 by Theodore Ts'o.
   5  *
   6  * Redistribution of this file is permitted under the terms of the GNU
   7  * Public License (GPL)
   8  *
   9  * These are the UART port assignments, expressed as offsets from the base
  10  * register.  These assignments should hold for any serial port based on
  11  * a 8250, 16450, or 16550(A).
  12  */
  13
  14 #ifndef _LINUX_SERIAL_REG_H
  15 #define _LINUX_SERIAL_REG_H
  16
  17 /*
  18  * DLAB=0
  19  */
  20 #define UART_RX         0       /* In:  Receive buffer */
  21 #define UART_TX         0       /* Out: Transmit buffer */
  22
  23 #define UART_IER        1       /* Out: Interrupt Enable Register */
  24 #define UART_IER_MSI            0x08 /* Enable Modem status interrupt */
  25 #define UART_IER_RLSI           0x04 /* Enable receiver line status interrupt */
  26 #define UART_IER_THRI           0x02 /* Enable Transmitter holding register int. */
  27 #define UART_IER_RDI            0x01 /* Enable receiver data interrupt */
  28 /*
  29  * Sleep mode for ST16650 and TI16750.  For the ST16650, EFR[4]=1
  30  */
  31 #define UART_IERX_SLEEP         0x10 /* Enable sleep mode */
  32
  33 #define UART_IIR        2       /* In:  Interrupt ID Register */
  34 #define UART_IIR_NO_INT         0x01 /* No interrupts pending */
  35 #define UART_IIR_ID             0x06 /* Mask for the interrupt ID */
  36 #define UART_IIR_MSI            0x00 /* Modem status interrupt */
  37 #define UART_IIR_THRI           0x02 /* Transmitter holding register empty */
  38 #define UART_IIR_RDI            0x04 /* Receiver data interrupt */
  39 #define UART_IIR_RLSI           0x06 /* Receiver line status interrupt */
  40
  41 #define UART_IIR_BUSY           0x07 /* DesignWare APB Busy Detect */
  42
  43 #define UART_FCR        2       /* Out: FIFO Control Register */
  44 #define UART_FCR_ENABLE_FIFO    0x01 /* Enable the FIFO */
  45 #define UART_FCR_CLEAR_RCVR     0x02 /* Clear the RCVR FIFO */
  46 #define UART_FCR_CLEAR_XMIT     0x04 /* Clear the XMIT FIFO */
  47 #define UART_FCR_DMA_SELECT     0x08 /* For DMA applications */
  48 /*
  49  * Note: The FIFO trigger levels are chip specific:
  50  *      RX:76 = 00  01  10  11  TX:54 = 00  01  10  11
  51  * PC16550D:     1   4   8  14          xx  xx  xx  xx
  52  * TI16C550A:    1   4   8  14          xx  xx  xx  xx
  53  * TI16C550C:    1   4   8  14          xx  xx  xx  xx
  54  * ST16C550:     1   4   8  14          xx  xx  xx  xx
  55  * ST16C650:     8  16  24  28          16   8  24  30  PORT_16650V2
  56  * NS16C552:     1   4   8  14          xx  xx  xx  xx
  57  * ST16C654:     8  16  56  60           8  16  32  56  PORT_16654
  58  * TI16C750:     1  16  32  56          xx  xx  xx  xx  PORT_16750
  59  * TI16C752:     8  16  56  60           8  16  32  56
  60  */
  61 #define UART_FCR_R_TRIG_00      0x00
  62 #define UART_FCR_R_TRIG_01      0x40
  63 #define UART_FCR_R_TRIG_10      0x80
  64 #define UART_FCR_R_TRIG_11      0xc0
  65 #define UART_FCR_T_TRIG_00      0x00
  66 #define UART_FCR_T_TRIG_01      0x10
  67 #define UART_FCR_T_TRIG_10      0x20
  68 #define UART_FCR_T_TRIG_11      0x30
  69
  70 #define UART_FCR_TRIGGER_MASK   0xC0 /* Mask for the FIFO trigger range */
  71 #define UART_FCR_TRIGGER_1      0x00 /* Mask for trigger set at 1 */
  72 #define UART_FCR_TRIGGER_4      0x40 /* Mask for trigger set at 4 */
  73 #define UART_FCR_TRIGGER_8      0x80 /* Mask for trigger set at 8 */
  74 #define UART_FCR_TRIGGER_14     0xC0 /* Mask for trigger set at 14 */
  75 /* 16650 definitions */
  76 #define UART_FCR6_R_TRIGGER_8   0x00 /* Mask for receive trigger set at 1 */
  77 #define UART_FCR6_R_TRIGGER_16  0x40 /* Mask for receive trigger set at 4 */
  78 #define UART_FCR6_R_TRIGGER_24  0x80 /* Mask for receive trigger set at 8 */
  79 #define UART_FCR6_R_TRIGGER_28  0xC0 /* Mask for receive trigger set at 14 */
  80 #define UART_FCR6_T_TRIGGER_16  0x00 /* Mask for transmit trigger set at 16 */
  81 #define UART_FCR6_T_TRIGGER_8   0x10 /* Mask for transmit trigger set at 8 */
  82 #define UART_FCR6_T_TRIGGER_24  0x20 /* Mask for transmit trigger set at 24 */
  83 #define UART_FCR6_T_TRIGGER_30  0x30 /* Mask for transmit trigger set at 30 */
  84 #define UART_FCR7_64BYTE        0x20 /* Go into 64 byte mode (TI16C750) */
  85
  86 #define UART_LCR        3       /* Out: Line Control Register */
  87 /*
  88  * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
  89  * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
  90  */
  91 #define UART_LCR_DLAB           0x80 /* Divisor latch access bit */
  92 #define UART_LCR_SBC            0x40 /* Set break control */
  93 #define UART_LCR_SPAR           0x20 /* Stick parity (?) */
  94 #define UART_LCR_EPAR           0x10 /* Even parity select */
  95 #define UART_LCR_PARITY         0x08 /* Parity Enable */
  96 #define UART_LCR_STOP           0x04 /* Stop bits: 0=1 bit, 1=2 bits */
  97 #define UART_LCR_WLEN5          0x00 /* Wordlength: 5 bits */
  98 #define UART_LCR_WLEN6          0x01 /* Wordlength: 6 bits */
  99 #define UART_LCR_WLEN7          0x02 /* Wordlength: 7 bits */
 100 #define UART_LCR_WLEN8          0x03 /* Wordlength: 8 bits */
 101
 102 #define UART_MCR        4       /* Out: Modem Control Register */
 103 #define UART_MCR_CLKSEL         0x80 /* Divide clock by 4 (TI16C752, EFR[4]=1) */
 104 #define UART_MCR_TCRTLR         0x40 /* Access TCR/TLR (TI16C752, EFR[4]=1) */
 105 #define UART_MCR_XONANY         0x20 /* Enable Xon Any (TI16C752, EFR[4]=1) */
 106 #define UART_MCR_AFE            0x20 /* Enable auto-RTS/CTS (TI16C550C/TI16C750) */
 107 #define UART_MCR_LOOP           0x10 /* Enable loopback test mode */
 108 #define UART_MCR_OUT2           0x08 /* Out2 complement */
 109 #define UART_MCR_OUT1           0x04 /* Out1 complement */
 110 #define UART_MCR_RTS            0x02 /* RTS complement */
 111 #define UART_MCR_DTR            0x01 /* DTR complement */
 112
 113 #define UART_LSR        5       /* In:  Line Status Register */
 114 #define UART_LSR_TEMT           0x40 /* Transmitter empty */
 115 #define UART_LSR_THRE           0x20 /* Transmit-hold-register empty */
 116 #define UART_LSR_BI             0x10 /* Break interrupt indicator */
 117 #define UART_LSR_FE             0x08 /* Frame error indicator */
 118 #define UART_LSR_PE             0x04 /* Parity error indicator */
 119 #define UART_LSR_OE             0x02 /* Overrun error indicator */
 120 #define UART_LSR_DR             0x01 /* Receiver data ready */
 121 #define UART_LSR_BRK_ERROR_BITS 0x1E /* BI, FE, PE, OE bits */
 122
 123 #define UART_MSR        6       /* In:  Modem Status Register */
 124 #define UART_MSR_DCD            0x80 /* Data Carrier Detect */
 125 #define UART_MSR_RI             0x40 /* Ring Indicator */
 126 #define UART_MSR_DSR            0x20 /* Data Set Ready */
 127 #define UART_MSR_CTS            0x10 /* Clear to Send */
 128 #define UART_MSR_DDCD           0x08 /* Delta DCD */
 129 #define UART_MSR_TERI           0x04 /* Trailing edge ring indicator */
 130 #define UART_MSR_DDSR           0x02 /* Delta DSR */
 131 #define UART_MSR_DCTS           0x01 /* Delta CTS */
 132 #define UART_MSR_ANY_DELTA      0x0F /* Any of the delta bits! */
 133
 134 #define UART_SCR        7       /* I/O: Scratch Register */
 135
 136 /*
 137  * DLAB=1
 138  */
 139 #define UART_DLL        0       /* Out: Divisor Latch Low */
 140 #define UART_DLM        1       /* Out: Divisor Latch High */
 141
 142 /*
 143  * LCR=0xBF (or DLAB=1 for 16C660)
 144  */
 145 #define UART_EFR        2       /* I/O: Extended Features Register */
 146 #define UART_EFR_CTS            0x80 /* CTS flow control */
 147 #define UART_EFR_RTS            0x40 /* RTS flow control */
 148 #define UART_EFR_SCD            0x20 /* Special character detect */
 149 #define UART_EFR_ECB            0x10 /* Enhanced control bit */
 150 /*
 151  * the low four bits control software flow control
 152  */
 153
 154 /*
 155  * LCR=0xBF, TI16C752, ST16650, ST16650A, ST16654
 156  */
 157 #define UART_XON1       4       /* I/O: Xon character 1 */
 158 #define UART_XON2       5       /* I/O: Xon character 2 */
 159 #define UART_XOFF1      6       /* I/O: Xoff character 1 */
 160 #define UART_XOFF2      7       /* I/O: Xoff character 2 */
 161
 162 /*
 163  * EFR[4]=1 MCR[6]=1, TI16C752
 164  */
 165 #define UART_TI752_TCR  6       /* I/O: transmission control register */
 166 #define UART_TI752_TLR  7       /* I/O: trigger level register */
 167
 168 /*
 169  * LCR=0xBF, XR16C85x
 170  */
 171 #define UART_TRG        0       /* FCTR bit 7 selects Rx or Tx
 172                                  * In: Fifo count
 173                                  * Out: Fifo custom trigger levels */
 174 /*
 175  * These are the definitions for the Programmable Trigger Register
 176  */
 177 #define UART_TRG_1              0x01
 178 #define UART_TRG_4              0x04
 179 #define UART_TRG_8              0x08
 180 #define UART_TRG_16             0x10
 181 #define UART_TRG_32             0x20
 182 #define UART_TRG_64             0x40
 183 #define UART_TRG_96             0x60
 184 #define UART_TRG_120            0x78
 185 #define UART_TRG_128            0x80
 186
 187 #define UART_FCTR       1       /* Feature Control Register */
 188 #define UART_FCTR_RTS_NODELAY   0x00  /* RTS flow control delay */
 189 #define UART_FCTR_RTS_4DELAY    0x01
 190 #define UART_FCTR_RTS_6DELAY    0x02
 191 #define UART_FCTR_RTS_8DELAY    0x03
 192 #define UART_FCTR_IRDA          0x04  /* IrDa data encode select */
 193 #define UART_FCTR_TX_INT        0x08  /* Tx interrupt type select */
 194 #define UART_FCTR_TRGA          0x00  /* Tx/Rx 550 trigger table select */
 195 #define UART_FCTR_TRGB          0x10  /* Tx/Rx 650 trigger table select */
 196 #define UART_FCTR_TRGC          0x20  /* Tx/Rx 654 trigger table select */
 197 #define UART_FCTR_TRGD          0x30  /* Tx/Rx 850 programmable trigger select */
 198 #define UART_FCTR_SCR_SWAP      0x40  /* Scratch pad register swap */
 199 #define UART_FCTR_RX            0x00  /* Programmable trigger mode select */
 200 #define UART_FCTR_TX            0x80  /* Programmable trigger mode select */
 201
 202 /*
 203  * LCR=0xBF, FCTR[6]=1
 204  */
 205 #define UART_EMSR       7       /* Extended Mode Select Register */
 206 #define UART_EMSR_FIFO_COUNT    0x01  /* Rx/Tx select */
 207 #define UART_EMSR_ALT_COUNT     0x02  /* Alternating count select */
 208
 209 /*
 210  * The Intel XScale on-chip UARTs define these bits
 211  */
 212 #define UART_IER_DMAE   0x80    /* DMA Requests Enable */
 213 #define UART_IER_UUE    0x40    /* UART Unit Enable */
 214 #define UART_IER_NRZE   0x20    /* NRZ coding Enable */
 215 #define UART_IER_RTOIE  0x10    /* Receiver Time Out Interrupt Enable */
 216
 217 #define UART_IIR_TOD    0x08    /* Character Timeout Indication Detected */
 218
 219 #define UART_FCR_PXAR1  0x00    /* receive FIFO treshold = 1 */
 220 #define UART_FCR_PXAR8  0x40    /* receive FIFO treshold = 8 */
 221 #define UART_FCR_PXAR16 0x80    /* receive FIFO treshold = 16 */
 222 #define UART_FCR_PXAR32 0xc0    /* receive FIFO treshold = 32 */
 223
 224
 225
 226
 227 /*
 228  * These register definitions are for the 16C950
 229  */
 230 #define UART_ASR        0x01    /* Additional Status Register */
 231 #define UART_RFL        0x03    /* Receiver FIFO level */
 232 #define UART_TFL        0x04    /* Transmitter FIFO level */
 233 #define UART_ICR        0x05    /* Index Control Register */
 234
 235 /* The 16950 ICR registers */
 236 #define UART_ACR        0x00    /* Additional Control Register */
 237 #define UART_CPR        0x01    /* Clock Prescalar Register */
 238 #define UART_TCR        0x02    /* Times Clock Register */
 239 #define UART_CKS        0x03    /* Clock Select Register */
 240 #define UART_TTL        0x04    /* Transmitter Interrupt Trigger Level */
 241 #define UART_RTL        0x05    /* Receiver Interrupt Trigger Level */
 242 #define UART_FCL        0x06    /* Flow Control Level Lower */
 243 #define UART_FCH        0x07    /* Flow Control Level Higher */
 244 #define UART_ID1        0x08    /* ID #1 */
 245 #define UART_ID2        0x09    /* ID #2 */
 246 #define UART_ID3        0x0A    /* ID #3 */
 247 #define UART_REV        0x0B    /* Revision */
 248 #define UART_CSR        0x0C    /* Channel Software Reset */
 249 #define UART_NMR        0x0D    /* Nine-bit Mode Register */
 250 #define UART_CTR        0xFF
 251
 252 /*
 253  * The 16C950 Additional Control Register
 254  */
 255 #define UART_ACR_RXDIS  0x01    /* Receiver disable */
 256 #define UART_ACR_TXDIS  0x02    /* Transmitter disable */
 257 #define UART_ACR_DSRFC  0x04    /* DSR Flow Control */
 258 #define UART_ACR_TLENB  0x20    /* 950 trigger levels enable */
 259 #define UART_ACR_ICRRD  0x40    /* ICR Read enable */
 260 #define UART_ACR_ASREN  0x80    /* Additional status enable */
 261
 262
 263
 264 /*
 265  * These definitions are for the RSA-DV II/S card, from
 266  *
 267  * Kiyokazu SUTO <suto@ks-and-ks.ne.jp>
 268  */
 269
 270 #define UART_RSA_BASE (-8)
 271
 272 #define UART_RSA_MSR ((UART_RSA_BASE) + 0) /* I/O: Mode Select Register */
 273
 274 #define UART_RSA_MSR_SWAP (1 << 0) /* Swap low/high 8 bytes in I/O port addr */
 275 #define UART_RSA_MSR_FIFO (1 << 2) /* Enable the external FIFO */
 276 #define UART_RSA_MSR_FLOW (1 << 3) /* Enable the auto RTS/CTS flow control */
 277 #define UART_RSA_MSR_ITYP (1 << 4) /* Level (1) / Edge triger (0) */
 278
 279 #define UART_RSA_IER ((UART_RSA_BASE) + 1) /* I/O: Interrupt Enable Register */
 280
 281 #define UART_RSA_IER_Rx_FIFO_H (1 << 0) /* Enable Rx FIFO half full int. */
 282 #define UART_RSA_IER_Tx_FIFO_H (1 << 1) /* Enable Tx FIFO half full int. */
 283 #define UART_RSA_IER_Tx_FIFO_E (1 << 2) /* Enable Tx FIFO empty int. */
 284 #define UART_RSA_IER_Rx_TOUT (1 << 3) /* Enable char receive timeout int */
 285 #define UART_RSA_IER_TIMER (1 << 4) /* Enable timer interrupt */
 286
 287 #define UART_RSA_SRR ((UART_RSA_BASE) + 2) /* IN: Status Read Register */
 288
 289 #define UART_RSA_SRR_Tx_FIFO_NEMP (1 << 0) /* Tx FIFO is not empty (1) */
 290 #define UART_RSA_SRR_Tx_FIFO_NHFL (1 << 1) /* Tx FIFO is not half full (1) */
 291 #define UART_RSA_SRR_Tx_FIFO_NFUL (1 << 2) /* Tx FIFO is not full (1) */
 292 #define UART_RSA_SRR_Rx_FIFO_NEMP (1 << 3) /* Rx FIFO is not empty (1) */
 293 #define UART_RSA_SRR_Rx_FIFO_NHFL (1 << 4) /* Rx FIFO is not half full (1) */
 294 #define UART_RSA_SRR_Rx_FIFO_NFUL (1 << 5) /* Rx FIFO is not full (1) */
 295 #define UART_RSA_SRR_Rx_TOUT (1 << 6) /* Character reception timeout occurred (1) */
 296 #define UART_RSA_SRR_TIMER (1 << 7) /* Timer interrupt occurred */
 297
 298 #define UART_RSA_FRR ((UART_RSA_BASE) + 2) /* OUT: FIFO Reset Register */
 299
 300 #define UART_RSA_TIVSR ((UART_RSA_BASE) + 3) /* I/O: Timer Interval Value Set Register */
 301
 302 #define UART_RSA_TCR ((UART_RSA_BASE) + 4) /* OUT: Timer Control Register */
 303
 304 #define UART_RSA_TCR_SWITCH (1 << 0) /* Timer on */
 305
 306 /*
 307  * The RSA DSV/II board has two fixed clock frequencies.  One is the
 308  * standard rate, and the other is 8 times faster.
 309  */
 310 #define SERIAL_RSA_BAUD_BASE (921600)
 311 #define SERIAL_RSA_BAUD_BASE_LO (SERIAL_RSA_BAUD_BASE / 8)
 312
 313 /*
 314  * Extra serial register definitions for the internal UARTs
 315  * in TI OMAP processors.
 316  */
 317 #define UART_OMAP_MDR1          0x08    /* Mode definition register */
 318 #define UART_OMAP_MDR2          0x09    /* Mode definition register 2 */
 319 #define UART_OMAP_SCR           0x10    /* Supplementary control register */
 320 #define UART_OMAP_SSR           0x11    /* Supplementary status register */
 321 #define UART_OMAP_EBLR          0x12    /* BOF length register */
 322 #define UART_OMAP_OSC_12M_SEL   0x13    /* OMAP1510 12MHz osc select */
 323 #define UART_OMAP_MVER          0x14    /* Module version register */
 324 #define UART_OMAP_SYSC          0x15    /* System configuration register */
 325 #define UART_OMAP_SYSS          0x16    /* System status register */
 326 #define UART_OMAP_WER           0x17    /* Wake-up enable register */
 327
 328 #endif /* _LINUX_SERIAL_REG_H */
 329