drivers/scsi/sun3_scsi.c

   1 /*
   2  * Sun3 SCSI stuff by Erik Verbruggen (erik@bigmama.xtdnet.nl)
   3  *
   4  * Sun3 DMA routines added by Sam Creasey (sammy@sammy.net)
   5  *
   6  * Adapted from mac_scsinew.c:
   7  */
   8 /*
   9  * Generic Macintosh NCR5380 driver
  10  *
  11  * Copyright 1998, Michael Schmitz <mschmitz@lbl.gov>
  12  *
  13  * derived in part from:
  14  */
  15 /*
  16  * Generic Generic NCR5380 driver
  17  *
  18  * Copyright 1995, Russell King
  19  *
  20  * ALPHA RELEASE 1.
  21  *
  22  * For more information, please consult
  23  *
  24  * NCR 5380 Family
  25  * SCSI Protocol Controller
  26  * Databook
  27  *
  28  * NCR Microelectronics
  29  * 1635 Aeroplaza Drive
  30  * Colorado Springs, CO 80916
  31  * 1+ (719) 578-3400
  32  * 1+ (800) 334-5454
  33  */
  34
  35
  36 /*
  37  * This is from mac_scsi.h, but hey, maybe this is useful for Sun3 too! :)
  38  *
  39  * Options :
  40  *
  41  * PARITY - enable parity checking.  Not supported.
  42  *
  43  * SCSI2 - enable support for SCSI-II tagged queueing.  Untested.
  44  *
  45  * USLEEP - enable support for devices that don't disconnect.  Untested.
  46  */
  47
  48 /*
  49  * $Log: sun3_NCR5380.c,v $
  50  */
  51
  52 #define AUTOSENSE
  53
  54 #include <linux/types.h>
  55 #include <linux/stddef.h>
  56 #include <linux/ctype.h>
  57 #include <linux/delay.h>
  58
  59 #include <linux/module.h>
  60 #include <linux/signal.h>
  61 #include <linux/ioport.h>
  62 #include <linux/init.h>
  63 #include <linux/blkdev.h>
  64
  65 #include <asm/io.h>
  66 #include <asm/system.h>
  67
  68 #include <asm/sun3ints.h>
  69 #include <asm/dvma.h>
  70 #include <asm/idprom.h>
  71 #include <asm/machines.h>
  72
  73 #define NDEBUG 0
  74
  75 #define NDEBUG_ABORT            0x00100000
  76 #define NDEBUG_TAGS             0x00200000
  77 #define NDEBUG_MERGING          0x00400000
  78
  79 /* dma on! */
  80 #define REAL_DMA
  81
  82 #include "scsi.h"
  83 #include "initio.h"
  84 #include <scsi/scsi_host.h>
  85 #include "sun3_scsi.h"
  86
  87 static void NCR5380_print(struct Scsi_Host *instance);
  88
  89 /* #define OLDDMA */
  90
  91 #define USE_WRAPPER
  92 /*#define RESET_BOOT */
  93 #define DRIVER_SETUP
  94
  95 /*
  96  * BUG can be used to trigger a strange code-size related hang on 2.1 kernels
  97  */
  98 #ifdef BUG
  99 #undef RESET_BOOT
 100 #undef DRIVER_SETUP
 101 #endif
 102
 103 /* #define SUPPORT_TAGS */
 104
 105 #define ENABLE_IRQ()    enable_irq( IRQ_SUN3_SCSI );
 106
 107
 108 static irqreturn_t scsi_sun3_intr(int irq, void *dummy);
 109 static inline unsigned char sun3scsi_read(int reg);
 110 static inline void sun3scsi_write(int reg, int value);
 111
 112 static int setup_can_queue = -1;
 113 module_param(setup_can_queue, int, 0);
 114 static int setup_cmd_per_lun = -1;
 115 module_param(setup_cmd_per_lun, int, 0);
 116 static int setup_sg_tablesize = -1;
 117 module_param(setup_sg_tablesize, int, 0);
 118 #ifdef SUPPORT_TAGS
 119 static int setup_use_tagged_queuing = -1;
 120 module_param(setup_use_tagged_queuing, int, 0);
 121 #endif
 122 static int setup_hostid = -1;
 123 module_param(setup_hostid, int, 0);
 124
 125 static struct scsi_cmnd *sun3_dma_setup_done = NULL;
 126
 127 #define AFTER_RESET_DELAY       (HZ/2)
 128
 129 /* ms to wait after hitting dma regs */
 130 #define SUN3_DMA_DELAY 10
 131
 132 /* dvma buffer to allocate -- 32k should hopefully be more than sufficient */
 133 #define SUN3_DVMA_BUFSIZE 0xe000
 134
 135 /* minimum number of bytes to do dma on */
 136 #define SUN3_DMA_MINSIZE 128
 137
 138 static volatile unsigned char *sun3_scsi_regp;
 139 static volatile struct sun3_dma_regs *dregs;
 140 #ifdef OLDDMA
 141 static unsigned char *dmabuf = NULL; /* dma memory buffer */
 142 #endif
 143 static struct sun3_udc_regs *udc_regs = NULL;
 144 static unsigned char *sun3_dma_orig_addr = NULL;
 145 static unsigned long sun3_dma_orig_count = 0;
 146 static int sun3_dma_active = 0;
 147 static unsigned long last_residual = 0;
 148
 149 /*
 150  * NCR 5380 register access functions
 151  */
 152
 153 static inline unsigned char sun3scsi_read(int reg)
 154 {
 155         return( sun3_scsi_regp[reg] );
 156 }
 157
 158 static inline void sun3scsi_write(int reg, int value)
 159 {
 160         sun3_scsi_regp[reg] = value;
 161 }
 162
 163 /* dma controller register access functions */
 164
 165 static inline unsigned short sun3_udc_read(unsigned char reg)
 166 {
 167         unsigned short ret;
 168
 169         dregs->udc_addr = UDC_CSR;
 170         udelay(SUN3_DMA_DELAY);
 171         ret = dregs->udc_data;
 172         udelay(SUN3_DMA_DELAY);
 173
 174         return ret;
 175 }
 176
 177 static inline void sun3_udc_write(unsigned short val, unsigned char reg)
 178 {
 179         dregs->udc_addr = reg;
 180         udelay(SUN3_DMA_DELAY);
 181         dregs->udc_data = val;
 182         udelay(SUN3_DMA_DELAY);
 183 }
 184
 185 /*
 186  * XXX: status debug
 187  */
 188 static struct Scsi_Host *default_instance;
 189
 190 /*
 191  * Function : int sun3scsi_detect(struct scsi_host_template * tpnt)
 192  *
 193  * Purpose : initializes mac NCR5380 driver based on the
 194  *      command line / compile time port and irq definitions.
 195  *
 196  * Inputs : tpnt - template for this SCSI adapter.
 197  *
 198  * Returns : 1 if a host adapter was found, 0 if not.
 199  *
 200  */
 201
 202 int __init sun3scsi_detect(struct scsi_host_template * tpnt)
 203 {
 204         unsigned long ioaddr;
 205         static int called = 0;
 206         struct Scsi_Host *instance;
 207
 208         /* check that this machine has an onboard 5380 */
 209         switch(idprom->id_machtype) {
 210         case SM_SUN3|SM_3_50:
 211         case SM_SUN3|SM_3_60:
 212                 break;
 213
 214         default:
 215                 return 0;
 216         }
 217
 218         if(called)
 219                 return 0;
 220
 221         tpnt->proc_name = "Sun3 5380 SCSI";
 222
 223         /* setup variables */
 224         tpnt->can_queue =
 225                 (setup_can_queue > 0) ? setup_can_queue : CAN_QUEUE;
 226         tpnt->cmd_per_lun =
 227                 (setup_cmd_per_lun > 0) ? setup_cmd_per_lun : CMD_PER_LUN;
 228         tpnt->sg_tablesize =
 229                 (setup_sg_tablesize >= 0) ? setup_sg_tablesize : SG_TABLESIZE;
 230
 231         if (setup_hostid >= 0)
 232                 tpnt->this_id = setup_hostid;
 233         else {
 234                 /* use 7 as default */
 235                 tpnt->this_id = 7;
 236         }
 237
 238         ioaddr = (unsigned long)ioremap(IOBASE_SUN3_SCSI, PAGE_SIZE);
 239         sun3_scsi_regp = (unsigned char *)ioaddr;
 240
 241         dregs = (struct sun3_dma_regs *)(((unsigned char *)ioaddr) + 8);
 242
 243         if((udc_regs = dvma_malloc(sizeof(struct sun3_udc_regs)))
 244            == NULL) {
 245              printk("SUN3 Scsi couldn't allocate DVMA memory!\n");
 246              return 0;
 247         }
 248 #ifdef OLDDMA
 249         if((dmabuf = dvma_malloc_align(SUN3_DVMA_BUFSIZE, 0x10000)) == NULL) {
 250              printk("SUN3 Scsi couldn't allocate DVMA memory!\n");
 251              return 0;
 252         }
 253 #endif
 254 #ifdef SUPPORT_TAGS
 255         if (setup_use_tagged_queuing < 0)
 256                 setup_use_tagged_queuing = USE_TAGGED_QUEUING;
 257 #endif
 258
 259         instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
 260         if(instance == NULL)
 261                 return 0;
 262
 263         default_instance = instance;
 264
 265         instance->io_port = (unsigned long) ioaddr;
 266         instance->irq = IRQ_SUN3_SCSI;
 267
 268         NCR5380_init(instance, 0);
 269
 270         instance->n_io_port = 32;
 271
 272         ((struct NCR5380_hostdata *)instance->hostdata)->ctrl = 0;
 273
 274         if (request_irq(instance->irq, scsi_sun3_intr,
 275                              0, "Sun3SCSI-5380", instance)) {
 276 #ifndef REAL_DMA
 277                 printk("scsi%d: IRQ%d not free, interrupts disabled\n",
 278                        instance->host_no, instance->irq);
 279                 instance->irq = SCSI_IRQ_NONE;
 280 #else
 281                 printk("scsi%d: IRQ%d not free, bailing out\n",
 282                        instance->host_no, instance->irq);
 283                 return 0;
 284 #endif
 285         }
 286
 287         printk("scsi%d: Sun3 5380 at port %lX irq", instance->host_no, instance->io_port);
 288         if (instance->irq == SCSI_IRQ_NONE)
 289                 printk ("s disabled");
 290         else
 291                 printk (" %d", instance->irq);
 292         printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d",
 293                instance->can_queue, instance->cmd_per_lun,
 294                SUN3SCSI_PUBLIC_RELEASE);
 295         printk("\nscsi%d:", instance->host_no);
 296         NCR5380_print_options(instance);
 297         printk("\n");
 298
 299         dregs->csr = 0;
 300         udelay(SUN3_DMA_DELAY);
 301         dregs->csr = CSR_SCSI | CSR_FIFO | CSR_INTR;
 302         udelay(SUN3_DMA_DELAY);
 303         dregs->fifo_count = 0;
 304
 305         called = 1;
 306
 307 #ifdef RESET_BOOT
 308         sun3_scsi_reset_boot(instance);
 309 #endif
 310
 311         return 1;
 312 }
 313
 314 int sun3scsi_release (struct Scsi_Host *shpnt)
 315 {
 316         if (shpnt->irq != SCSI_IRQ_NONE)
 317                 free_irq(shpnt->irq, shpnt);
 318
 319         iounmap((void *)sun3_scsi_regp);
 320
 321         NCR5380_exit(shpnt);
 322         return 0;
 323 }
 324
 325 #ifdef RESET_BOOT
 326 /*
 327  * Our 'bus reset on boot' function
 328  */
 329
 330 static void sun3_scsi_reset_boot(struct Scsi_Host *instance)
 331 {
 332         unsigned long end;
 333
 334         NCR5380_local_declare();
 335         NCR5380_setup(instance);
 336
 337         /*
 338          * Do a SCSI reset to clean up the bus during initialization. No
 339          * messing with the queues, interrupts, or locks necessary here.
 340          */
 341
 342         printk( "Sun3 SCSI: resetting the SCSI bus..." );
 343
 344         /* switch off SCSI IRQ - catch an interrupt without IRQ bit set else */
 345 //              sun3_disable_irq( IRQ_SUN3_SCSI );
 346
 347         /* get in phase */
 348         NCR5380_write( TARGET_COMMAND_REG,
 349                       PHASE_SR_TO_TCR( NCR5380_read(STATUS_REG) ));
 350
 351         /* assert RST */
 352         NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST );
 353
 354         /* The min. reset hold time is 25us, so 40us should be enough */
 355         udelay( 50 );
 356
 357         /* reset RST and interrupt */
 358         NCR5380_write( INITIATOR_COMMAND_REG, ICR_BASE );
 359         NCR5380_read( RESET_PARITY_INTERRUPT_REG );
 360
 361         for( end = jiffies + AFTER_RESET_DELAY; time_before(jiffies, end); )
 362                 barrier();
 363
 364         /* switch on SCSI IRQ again */
 365 //              sun3_enable_irq( IRQ_SUN3_SCSI );
 366
 367         printk( " done\n" );
 368 }
 369 #endif
 370
 371 const char * sun3scsi_info (struct Scsi_Host *spnt) {
 372     return "";
 373 }
 374
 375 // safe bits for the CSR
 376 #define CSR_GOOD 0x060f
 377
 378 static irqreturn_t scsi_sun3_intr(int irq, void *dummy)
 379 {
 380         unsigned short csr = dregs->csr;
 381         int handled = 0;
 382
 383         if(csr & ~CSR_GOOD) {
 384                 if(csr & CSR_DMA_BUSERR) {
 385                         printk("scsi%d: bus error in dma\n", default_instance->host_no);
 386                 }
 387
 388                 if(csr & CSR_DMA_CONFLICT) {
 389                         printk("scsi%d: dma conflict\n", default_instance->host_no);
 390                 }
 391                 handled = 1;
 392         }
 393
 394         if(csr & (CSR_SDB_INT | CSR_DMA_INT)) {
 395                 NCR5380_intr(irq, dummy);
 396                 handled = 1;
 397         }
 398
 399         return IRQ_RETVAL(handled);
 400 }
 401
 402 /*
 403  * Debug stuff - to be called on NMI, or sysrq key. Use at your own risk;
 404  * reentering NCR5380_print_status seems to have ugly side effects
 405  */
 406
 407 /* this doesn't seem to get used at all -- sam */
 408 #if 0
 409 void sun3_sun3_debug (void)
 410 {
 411         unsigned long flags;
 412         NCR5380_local_declare();
 413
 414         if (default_instance) {
 415                         local_irq_save(flags);
 416                         NCR5380_print_status(default_instance);
 417                         local_irq_restore(flags);
 418         }
 419 }
 420 #endif
 421
 422
 423 /* sun3scsi_dma_setup() -- initialize the dma controller for a read/write */
 424 static unsigned long sun3scsi_dma_setup(void *data, unsigned long count, int write_flag)
 425 {
 426 #ifdef OLDDMA
 427         if(write_flag)
 428                 memcpy(dmabuf, data, count);
 429         else {
 430                 sun3_dma_orig_addr = data;
 431                 sun3_dma_orig_count = count;
 432         }
 433 #else
 434         void *addr;
 435
 436         if(sun3_dma_orig_addr != NULL)
 437                 dvma_unmap(sun3_dma_orig_addr);
 438
 439 //      addr = sun3_dvma_page((unsigned long)data, (unsigned long)dmabuf);
 440         addr = (void *)dvma_map((unsigned long) data, count);
 441
 442         sun3_dma_orig_addr = addr;
 443         sun3_dma_orig_count = count;
 444 #endif
 445         dregs->fifo_count = 0;
 446         sun3_udc_write(UDC_RESET, UDC_CSR);
 447
 448         /* reset fifo */
 449         dregs->csr &= ~CSR_FIFO;
 450         dregs->csr |= CSR_FIFO;
 451
 452         /* set direction */
 453         if(write_flag)
 454                 dregs->csr |= CSR_SEND;
 455         else
 456                 dregs->csr &= ~CSR_SEND;
 457
 458         /* byte count for fifo */
 459         dregs->fifo_count = count;
 460
 461         sun3_udc_write(UDC_RESET, UDC_CSR);
 462
 463         /* reset fifo */
 464         dregs->csr &= ~CSR_FIFO;
 465         dregs->csr |= CSR_FIFO;
 466
 467         if(dregs->fifo_count != count) {
 468                 printk("scsi%d: fifo_mismatch %04x not %04x\n",
 469                        default_instance->host_no, dregs->fifo_count,
 470                        (unsigned int) count);
 471                 NCR5380_print(default_instance);
 472         }
 473
 474         /* setup udc */
 475 #ifdef OLDDMA
 476         udc_regs->addr_hi = ((dvma_vtob(dmabuf) & 0xff0000) >> 8);
 477         udc_regs->addr_lo = (dvma_vtob(dmabuf) & 0xffff);
 478 #else
 479         udc_regs->addr_hi = (((unsigned long)(addr) & 0xff0000) >> 8);
 480         udc_regs->addr_lo = ((unsigned long)(addr) & 0xffff);
 481 #endif
 482         udc_regs->count = count/2; /* count in words */
 483         udc_regs->mode_hi = UDC_MODE_HIWORD;
 484         if(write_flag) {
 485                 if(count & 1)
 486                         udc_regs->count++;
 487                 udc_regs->mode_lo = UDC_MODE_LSEND;
 488                 udc_regs->rsel = UDC_RSEL_SEND;
 489         } else {
 490                 udc_regs->mode_lo = UDC_MODE_LRECV;
 491                 udc_regs->rsel = UDC_RSEL_RECV;
 492         }
 493
 494         /* announce location of regs block */
 495         sun3_udc_write(((dvma_vtob(udc_regs) & 0xff0000) >> 8),
 496                        UDC_CHN_HI);
 497
 498         sun3_udc_write((dvma_vtob(udc_regs) & 0xffff), UDC_CHN_LO);
 499
 500         /* set dma master on */
 501         sun3_udc_write(0xd, UDC_MODE);
 502
 503         /* interrupt enable */
 504         sun3_udc_write(UDC_INT_ENABLE, UDC_CSR);
 505
 506         return count;
 507
 508 }
 509
 510 static inline unsigned long sun3scsi_dma_count(struct Scsi_Host *instance)
 511 {
 512         unsigned short resid;
 513
 514         dregs->udc_addr = 0x32;
 515         udelay(SUN3_DMA_DELAY);
 516         resid = dregs->udc_data;
 517         udelay(SUN3_DMA_DELAY);
 518         resid *= 2;
 519
 520         return (unsigned long) resid;
 521 }
 522
 523 static inline unsigned long sun3scsi_dma_residual(struct Scsi_Host *instance)
 524 {
 525         return last_residual;
 526 }
 527
 528 static inline unsigned long sun3scsi_dma_xfer_len(unsigned long wanted,
 529                                                   struct scsi_cmnd *cmd,
 530                                                   int write_flag)
 531 {
 532         if (cmd->request->cmd_type == REQ_TYPE_FS)
 533                 return wanted;
 534         else
 535                 return 0;
 536 }
 537
 538 static inline int sun3scsi_dma_start(unsigned long count, unsigned char *data)
 539 {
 540
 541     sun3_udc_write(UDC_CHN_START, UDC_CSR);
 542
 543     return 0;
 544 }
 545
 546 /* clean up after our dma is done */
 547 static int sun3scsi_dma_finish(int write_flag)
 548 {
 549         unsigned short count;
 550         unsigned short fifo;
 551         int ret = 0;
 552
 553         sun3_dma_active = 0;
 554 #if 1
 555         // check to empty the fifo on a read
 556         if(!write_flag) {
 557                 int tmo = 20000; /* .2 sec */
 558
 559                 while(1) {
 560                         if(dregs->csr & CSR_FIFO_EMPTY)
 561                                 break;
 562
 563                         if(--tmo <= 0) {
 564                                 printk("sun3scsi: fifo failed to empty!\n");
 565                                 return 1;
 566                         }
 567                         udelay(10);
 568                 }
 569         }
 570
 571 #endif
 572
 573         count = sun3scsi_dma_count(default_instance);
 574 #ifdef OLDDMA
 575
 576         /* if we've finished a read, copy out the data we read */
 577         if(sun3_dma_orig_addr) {
 578                 /* check for residual bytes after dma end */
 579                 if(count && (NCR5380_read(BUS_AND_STATUS_REG) &
 580                              (BASR_PHASE_MATCH | BASR_ACK))) {
 581                         printk("scsi%d: sun3_scsi_finish: read overrun baby... ", default_instance->host_no);
 582                         printk("basr now %02x\n", NCR5380_read(BUS_AND_STATUS_REG));
 583                         ret = count;
 584                 }
 585
 586                 /* copy in what we dma'd no matter what */
 587                 memcpy(sun3_dma_orig_addr, dmabuf, sun3_dma_orig_count);
 588                 sun3_dma_orig_addr = NULL;
 589
 590         }
 591 #else
 592
 593         fifo = dregs->fifo_count;
 594         last_residual = fifo;
 595
 596         /* empty bytes from the fifo which didn't make it */
 597         if((!write_flag) && (count - fifo) == 2) {
 598                 unsigned short data;
 599                 unsigned char *vaddr;
 600
 601                 data = dregs->fifo_data;
 602                 vaddr = (unsigned char *)dvma_btov(sun3_dma_orig_addr);
 603
 604                 vaddr += (sun3_dma_orig_count - fifo);
 605
 606                 vaddr[-2] = (data & 0xff00) >> 8;
 607                 vaddr[-1] = (data & 0xff);
 608         }
 609
 610         dvma_unmap(sun3_dma_orig_addr);
 611         sun3_dma_orig_addr = NULL;
 612 #endif
 613         sun3_udc_write(UDC_RESET, UDC_CSR);
 614         dregs->fifo_count = 0;
 615         dregs->csr &= ~CSR_SEND;
 616
 617         /* reset fifo */
 618         dregs->csr &= ~CSR_FIFO;
 619         dregs->csr |= CSR_FIFO;
 620
 621         sun3_dma_setup_done = NULL;
 622
 623         return ret;
 624
 625 }
 626
 627 #include "sun3_NCR5380.c"
 628
 629 static struct scsi_host_template driver_template = {
 630         .name                   = SUN3_SCSI_NAME,
 631         .detect                 = sun3scsi_detect,
 632         .release                = sun3scsi_release,
 633         .info                   = sun3scsi_info,
 634         .queuecommand           = sun3scsi_queue_command,
 635         .eh_abort_handler       = sun3scsi_abort,
 636         .eh_bus_reset_handler   = sun3scsi_bus_reset,
 637         .can_queue              = CAN_QUEUE,
 638         .this_id                = 7,
 639         .sg_tablesize           = SG_TABLESIZE,
 640         .cmd_per_lun            = CMD_PER_LUN,
 641         .use_clustering         = DISABLE_CLUSTERING
 642 };
 643
 644
 645 #include "scsi_module.c"
 646
 647 MODULE_LICENSE("GPL");