include/asm-parisc/superio.h

   1 #ifndef _PARISC_SUPERIO_H
   2 #define _PARISC_SUPERIO_H
   3
   4 #define IC_PIC1    0x20         /* PCI I/O address of master 8259 */
   5 #define IC_PIC2    0xA0         /* PCI I/O address of slave */
   6
   7 /* Config Space Offsets to configuration and base address registers */
   8 #define SIO_CR     0x5A         /* Configuration Register */
   9 #define SIO_ACPIBAR 0x88        /* ACPI BAR */
  10 #define SIO_FDCBAR 0x90         /* Floppy Disk Controller BAR */
  11 #define SIO_SP1BAR 0x94         /* Serial 1 BAR */
  12 #define SIO_SP2BAR 0x98         /* Serial 2 BAR */
  13 #define SIO_PPBAR  0x9C         /* Parallel BAR */
  14
  15 #define TRIGGER_1  0x67         /* Edge/level trigger register 1 */
  16 #define TRIGGER_2  0x68         /* Edge/level trigger register 2 */
  17
  18 /* Interrupt Routing Control registers */
  19 #define CFG_IR_SER    0x69      /* Serial 1 [0:3] and Serial 2 [4:7] */
  20 #define CFG_IR_PFD    0x6a      /* Parallel [0:3] and Floppy [4:7] */
  21 #define CFG_IR_IDE    0x6b      /* IDE1     [0:3] and IDE2 [4:7] */
  22 #define CFG_IR_INTAB  0x6c      /* PCI INTA [0:3] and INT B [4:7] */
  23 #define CFG_IR_INTCD  0x6d      /* PCI INTC [0:3] and INT D [4:7] */
  24 #define CFG_IR_PS2    0x6e      /* PS/2 KBINT [0:3] and Mouse [4:7] */
  25 #define CFG_IR_FXBUS  0x6f      /* FXIRQ[0] [0:3] and FXIRQ[1] [4:7] */
  26 #define CFG_IR_USB    0x70      /* FXIRQ[2] [0:3] and USB [4:7] */
  27 #define CFG_IR_ACPI   0x71      /* ACPI SCI [0:3] and reserved [4:7] */
  28
  29 #define CFG_IR_LOW     CFG_IR_SER       /* Lowest interrupt routing reg */
  30 #define CFG_IR_HIGH    CFG_IR_ACPI      /* Highest interrupt routing reg */
  31
  32 /* 8259 operational control words */
  33 #define OCW2_EOI   0x20         /* Non-specific EOI */
  34 #define OCW2_SEOI  0x60         /* Specific EOI */
  35 #define OCW3_IIR   0x0A         /* Read request register */
  36 #define OCW3_ISR   0x0B         /* Read service register */
  37 #define OCW3_POLL  0x0C         /* Poll the PIC for an interrupt vector */
  38
  39 /* Interrupt lines. Only PIC1 is used */
  40 #define USB_IRQ    1            /* USB */
  41 #define SP1_IRQ    3            /* Serial port 1 */
  42 #define SP2_IRQ    4            /* Serial port 2 */
  43 #define PAR_IRQ    5            /* Parallel port */
  44 #define FDC_IRQ    6            /* Floppy controller */
  45 #define IDE_IRQ    7            /* IDE (pri+sec) */
  46
  47 /* ACPI registers */
  48 #define USB_REG_CR      0x1f    /* USB Regulator Control Register */
  49
  50 #define SUPERIO_NIRQS   8
  51
  52 struct superio_device {
  53         u32 fdc_base;
  54         u32 sp1_base;
  55         u32 sp2_base;
  56         u32 pp_base;
  57         u32 acpi_base;
  58         int suckyio_irq_enabled;
  59         struct pci_dev *lio_pdev;       /* pci device for legacy IO (fn 1) */
  60         struct pci_dev *usb_pdev;       /* pci device for USB (fn 2) */
  61 };
  62
  63 /*
  64  * Does NS make a 87415 based plug in PCI card? If so, because of this
  65  * macro we currently don't support it being plugged into a machine
  66  * that contains a SuperIO chip AND has CONFIG_SUPERIO enabled.
  67  *
  68  * This could be fixed by checking to see if function 1 exists, and
  69  * if it is SuperIO Legacy IO; but really now, is this combination
  70  * going to EVER happen?
  71  */
  72
  73 #define SUPERIO_IDE_FN 0 /* Function number of IDE controller */
  74 #define SUPERIO_LIO_FN 1 /* Function number of Legacy IO controller */
  75 #define SUPERIO_USB_FN 2 /* Function number of USB controller */
  76
  77 #define is_superio_device(x) \
  78         (((x)->vendor == PCI_VENDOR_ID_NS) && \
  79         (  ((x)->device == PCI_DEVICE_ID_NS_87415) \
  80         || ((x)->device == PCI_DEVICE_ID_NS_87560_LIO) \
  81         || ((x)->device == PCI_DEVICE_ID_NS_87560_USB) ) )
  82
  83 extern int superio_fixup_irq(struct pci_dev *pcidev); /* called by iosapic */
  84
  85 #endif /* _PARISC_SUPERIO_H */