Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...

[linux-stable.git] / lib / decompress_unxz.c

// SPDX-License-Identifier: 0BSD

/*
 * Wrapper for decompressing XZ-compressed kernel, initramfs, and initrd
 *
 * Author: Lasse Collin <lasse.collin@tukaani.org>
 */

/*
 * Important notes about in-place decompression
 *
 * At least on x86, the kernel is decompressed in place: the compressed data
 * is placed to the end of the output buffer, and the decompressor overwrites
 * most of the compressed data. There must be enough safety margin to
 * guarantee that the write position is always behind the read position.
 *
 * The safety margin for XZ with LZMA2 or BCJ+LZMA2 is calculated below.
 * Note that the margin with XZ is bigger than with Deflate (gzip)!
 *
 * The worst case for in-place decompression is that the beginning of
 * the file is compressed extremely well, and the rest of the file is
 * incompressible. Thus, we must look for worst-case expansion when the
 * compressor is encoding incompressible data.
 *
 * The structure of the .xz file in case of a compressed kernel is as follows.
 * Sizes (as bytes) of the fields are in parenthesis.
 *
 *    Stream Header (12)
 *    Block Header:
 *      Block Header (8-12)
 *      Compressed Data (N)
 *      Block Padding (0-3)
 *      CRC32 (4)
 *    Index (8-20)
 *    Stream Footer (12)
 *
 * Normally there is exactly one Block, but let's assume that there are
 * 2-4 Blocks just in case. Because Stream Header and also Block Header
 * of the first Block don't make the decompressor produce any uncompressed
 * data, we can ignore them from our calculations. Block Headers of possible
 * additional Blocks have to be taken into account still. With these
 * assumptions, it is safe to assume that the total header overhead is
 * less than 128 bytes.
 *
 * Compressed Data contains LZMA2 or BCJ+LZMA2 encoded data. Since BCJ
 * doesn't change the size of the data, it is enough to calculate the
 * safety margin for LZMA2.
 *
 * LZMA2 stores the data in chunks. Each chunk has a header whose size is
 * a maximum of 6 bytes, but to get round 2^n numbers, let's assume that
 * the maximum chunk header size is 8 bytes. After the chunk header, there
 * may be up to 64 KiB of actual payload in the chunk. Often the payload is
 * quite a bit smaller though; to be safe, let's assume that an average
 * chunk has only 32 KiB of payload.
 *
 * The maximum uncompressed size of the payload is 2 MiB. The minimum
 * uncompressed size of the payload is in practice never less than the
 * payload size itself. The LZMA2 format would allow uncompressed size
 * to be less than the payload size, but no sane compressor creates such
 * files. LZMA2 supports storing incompressible data in uncompressed form,
 * so there's never a need to create payloads whose uncompressed size is
 * smaller than the compressed size.
 *
 * The assumption, that the uncompressed size of the payload is never
 * smaller than the payload itself, is valid only when talking about
 * the payload as a whole. It is possible that the payload has parts where
 * the decompressor consumes more input than it produces output. Calculating
 * the worst case for this would be tricky. Instead of trying to do that,
 * let's simply make sure that the decompressor never overwrites any bytes
 * of the payload which it is currently reading.
 *
 * Now we have enough information to calculate the safety margin. We need
 *   - 128 bytes for the .xz file format headers;
 *   - 8 bytes per every 32 KiB of uncompressed size (one LZMA2 chunk header
 *     per chunk, each chunk having average payload size of 32 KiB); and
 *   - 64 KiB (biggest possible LZMA2 chunk payload size) to make sure that
 *     the decompressor never overwrites anything from the LZMA2 chunk
 *     payload it is currently reading.
 *
 * We get the following formula:
 *
 *    safety_margin = 128 + uncompressed_size * 8 / 32768 + 65536
 *                  = 128 + (uncompressed_size >> 12) + 65536
 *
 * For comparison, according to arch/x86/boot/compressed/misc.c, the
 * equivalent formula for Deflate is this:
 *
 *    safety_margin = 18 + (uncompressed_size >> 12) + 32768
 *
 * Thus, when updating Deflate-only in-place kernel decompressor to
 * support XZ, the fixed overhead has to be increased from 18+32768 bytes
 * to 128+65536 bytes.
 */

/*
 * STATIC is defined to "static" if we are being built for kernel
 * decompression (pre-boot code). <linux/decompress/mm.h> will define
 * STATIC to empty if it wasn't already defined. Since we will need to
 * know later if we are being used for kernel decompression, we define
 * XZ_PREBOOT here.
 */
#ifdef STATIC
#       define XZ_PREBOOT
#else
#       include <linux/decompress/unxz.h>
#endif
#ifdef __KERNEL__
#       include <linux/decompress/mm.h>
#endif

#ifndef XZ_PREBOOT
#       include <linux/slab.h>
#       include <linux/xz.h>
#else
/*
 * Use the internal CRC32 code instead of kernel's CRC32 module, which
 * is not available in early phase of booting.
 */
#define XZ_INTERNAL_CRC32 1

/*
 * For boot time use, we enable only the BCJ filter of the current
 * architecture or none if no BCJ filter is available for the architecture.
 */
#ifdef CONFIG_X86
#       define XZ_DEC_X86
#endif
#if defined(CONFIG_PPC) && defined(CONFIG_CPU_BIG_ENDIAN)
#       define XZ_DEC_POWERPC
#endif
#ifdef CONFIG_ARM
#       ifdef CONFIG_THUMB2_KERNEL
#               define XZ_DEC_ARMTHUMB
#       else
#               define XZ_DEC_ARM
#       endif
#endif
#ifdef CONFIG_ARM64
#       define XZ_DEC_ARM64
#endif
#ifdef CONFIG_RISCV
#       define XZ_DEC_RISCV
#endif
#ifdef CONFIG_SPARC
#       define XZ_DEC_SPARC
#endif

/*
 * This will get the basic headers so that memeq() and others
 * can be defined.
 */
#include "xz/xz_private.h"

/*
 * Replace the normal allocation functions with the versions from
 * <linux/decompress/mm.h>. vfree() needs to support vfree(NULL)
 * when XZ_DYNALLOC is used, but the pre-boot free() doesn't support it.
 * Workaround it here because the other decompressors don't need it.
 */
#undef kmalloc
#undef kfree
#undef vmalloc
#undef vfree
#define kmalloc(size, flags) malloc(size)
#define kfree(ptr) free(ptr)
#define vmalloc(size) malloc(size)
#define vfree(ptr) do { if (ptr != NULL) free(ptr); } while (0)

/*
 * FIXME: Not all basic memory functions are provided in architecture-specific
 * files (yet). We define our own versions here for now, but this should be
 * only a temporary solution.
 *
 * memeq and memzero are not used much and any remotely sane implementation
 * is fast enough. memcpy/memmove speed matters in multi-call mode, but
 * the kernel image is decompressed in single-call mode, in which only
 * memmove speed can matter and only if there is a lot of incompressible data
 * (LZMA2 stores incompressible chunks in uncompressed form). Thus, the
 * functions below should just be kept small; it's probably not worth
 * optimizing for speed.
 */

#ifndef memeq
static bool memeq(const void *a, const void *b, size_t size)
{
        const uint8_t *x = a;
        const uint8_t *y = b;
        size_t i;

        for (i = 0; i < size; ++i)
                if (x[i] != y[i])
                        return false;

        return true;
}
#endif

#ifndef memzero
static void memzero(void *buf, size_t size)
{
        uint8_t *b = buf;
        uint8_t *e = b + size;

        while (b != e)
                *b++ = '\0';
}
#endif

#ifndef memmove
/* Not static to avoid a conflict with the prototype in the Linux headers. */
void *memmove(void *dest, const void *src, size_t size)
{
        uint8_t *d = dest;
        const uint8_t *s = src;
        size_t i;

        if (d < s) {
                for (i = 0; i < size; ++i)
                        d[i] = s[i];
        } else if (d > s) {
                i = size;
                while (i-- > 0)
                        d[i] = s[i];
        }

        return dest;
}
#endif

/*
 * Since we need memmove anyway, we could use it as memcpy too.
 * Commented out for now to avoid breaking things.
 */
/*
#ifndef memcpy
#       define memcpy memmove
#endif
*/

#include "xz/xz_crc32.c"
#include "xz/xz_dec_stream.c"
#include "xz/xz_dec_lzma2.c"
#include "xz/xz_dec_bcj.c"

#endif /* XZ_PREBOOT */

/* Size of the input and output buffers in multi-call mode */
#define XZ_IOBUF_SIZE 4096

/*
 * This function implements the API defined in <linux/decompress/generic.h>.
 *
 * This wrapper will automatically choose single-call or multi-call mode
 * of the native XZ decoder API. The single-call mode can be used only when
 * both input and output buffers are available as a single chunk, i.e. when
 * fill() and flush() won't be used.
 */
STATIC int INIT unxz(unsigned char *in, long in_size,
                     long (*fill)(void *dest, unsigned long size),
                     long (*flush)(void *src, unsigned long size),
                     unsigned char *out, long *in_used,
                     void (*error)(char *x))
{
        struct xz_buf b;
        struct xz_dec *s;
        enum xz_ret ret;
        bool must_free_in = false;

#if XZ_INTERNAL_CRC32
        xz_crc32_init();
#endif

        if (in_used != NULL)
                *in_used = 0;

        if (fill == NULL && flush == NULL)
                s = xz_dec_init(XZ_SINGLE, 0);
        else
                s = xz_dec_init(XZ_DYNALLOC, (uint32_t)-1);

        if (s == NULL)
                goto error_alloc_state;

        if (flush == NULL) {
                b.out = out;
                b.out_size = (size_t)-1;
        } else {
                b.out_size = XZ_IOBUF_SIZE;
                b.out = malloc(XZ_IOBUF_SIZE);
                if (b.out == NULL)
                        goto error_alloc_out;
        }

        if (in == NULL) {
                must_free_in = true;
                in = malloc(XZ_IOBUF_SIZE);
                if (in == NULL)
                        goto error_alloc_in;
        }

        b.in = in;
        b.in_pos = 0;
        b.in_size = in_size;
        b.out_pos = 0;

        if (fill == NULL && flush == NULL) {
                ret = xz_dec_run(s, &b);
        } else {
                do {
                        if (b.in_pos == b.in_size && fill != NULL) {
                                if (in_used != NULL)
                                        *in_used += b.in_pos;

                                b.in_pos = 0;

                                in_size = fill(in, XZ_IOBUF_SIZE);
                                if (in_size < 0) {
                                        /*
                                         * This isn't an optimal error code
                                         * but it probably isn't worth making
                                         * a new one either.
                                         */
                                        ret = XZ_BUF_ERROR;
                                        break;
                                }

                                b.in_size = in_size;
                        }

                        ret = xz_dec_run(s, &b);

                        if (flush != NULL && (b.out_pos == b.out_size
                                        || (ret != XZ_OK && b.out_pos > 0))) {
                                /*
                                 * Setting ret here may hide an error
                                 * returned by xz_dec_run(), but probably
                                 * it's not too bad.
                                 */
                                if (flush(b.out, b.out_pos) != (long)b.out_pos)
                                        ret = XZ_BUF_ERROR;

                                b.out_pos = 0;
                        }
                } while (ret == XZ_OK);

                if (must_free_in)
                        free(in);

                if (flush != NULL)
                        free(b.out);
        }

        if (in_used != NULL)
                *in_used += b.in_pos;

        xz_dec_end(s);

        switch (ret) {
        case XZ_STREAM_END:
                return 0;

        case XZ_MEM_ERROR:
                /* This can occur only in multi-call mode. */
                error("XZ decompressor ran out of memory");
                break;

        case XZ_FORMAT_ERROR:
                error("Input is not in the XZ format (wrong magic bytes)");
                break;

        case XZ_OPTIONS_ERROR:
                error("Input was encoded with settings that are not "
                                "supported by this XZ decoder");
                break;

        case XZ_DATA_ERROR:
        case XZ_BUF_ERROR:
                error("XZ-compressed data is corrupt");
                break;

        default:
                error("Bug in the XZ decompressor");
                break;
        }

        return -1;

error_alloc_in:
        if (flush != NULL)
                free(b.out);

error_alloc_out:
        xz_dec_end(s);

error_alloc_state:
        error("XZ decompressor ran out of memory");
        return -1;
}

/*
 * This function is used by architecture-specific files to decompress
 * the kernel image.
 */
#ifdef XZ_PREBOOT
STATIC int INIT __decompress(unsigned char *in, long in_size,
                             long (*fill)(void *dest, unsigned long size),
                             long (*flush)(void *src, unsigned long size),
                             unsigned char *out, long out_size,
                             long *in_used,
                             void (*error)(char *x))
{
        return unxz(in, in_size, fill, flush, out, in_used, error);
}
#endif