drivers/scsi/pm8001/pm8001_hwi.h

   1 /*
   2  * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver
   3  *
   4  * Copyright (c) 2008-2009 USI Co., Ltd.
   5  * All rights reserved.
   6  *
   7  * Redistribution and use in source and binary forms, with or without
   8  * modification, are permitted provided that the following conditions
   9  * are met:
  10  * 1. Redistributions of source code must retain the above copyright
  11  *    notice, this list of conditions, and the following disclaimer,
  12  *    without modification.
  13  * 2. Redistributions in binary form must reproduce at minimum a disclaimer
  14  *    substantially similar to the "NO WARRANTY" disclaimer below
  15  *    ("Disclaimer") and any redistribution must be conditioned upon
  16  *    including a substantially similar Disclaimer requirement for further
  17  *    binary redistribution.
  18  * 3. Neither the names of the above-listed copyright holders nor the names
  19  *    of any contributors may be used to endorse or promote products derived
  20  *    from this software without specific prior written permission.
  21  *
  22  * Alternatively, this software may be distributed under the terms of the
  23  * GNU General Public License ("GPL") version 2 as published by the Free
  24  * Software Foundation.
  25  *
  26  * NO WARRANTY
  27  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
  28  * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
  29  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
  30  * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
  31  * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  32  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
  33  * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  34  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  35  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
  36  * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
  37  * POSSIBILITY OF SUCH DAMAGES.
  38  *
  39  */
  40 #ifndef _PMC8001_REG_H_
  41 #define _PMC8001_REG_H_
  42
  43 #include <linux/types.h>
  44 #include <scsi/libsas.h>
  45
  46
  47 /* for Request Opcode of IOMB */
  48 #define OPC_INB_ECHO                            1       /* 0x000 */
  49 #define OPC_INB_PHYSTART                        4       /* 0x004 */
  50 #define OPC_INB_PHYSTOP                         5       /* 0x005 */
  51 #define OPC_INB_SSPINIIOSTART                   6       /* 0x006 */
  52 #define OPC_INB_SSPINITMSTART                   7       /* 0x007 */
  53 #define OPC_INB_SSPINIEXTIOSTART                8       /* 0x008 */
  54 #define OPC_INB_DEV_HANDLE_ACCEPT               9       /* 0x009 */
  55 #define OPC_INB_SSPTGTIOSTART                   10      /* 0x00A */
  56 #define OPC_INB_SSPTGTRSPSTART                  11      /* 0x00B */
  57 #define OPC_INB_SSPINIEDCIOSTART                12      /* 0x00C */
  58 #define OPC_INB_SSPINIEXTEDCIOSTART             13      /* 0x00D */
  59 #define OPC_INB_SSPTGTEDCIOSTART                14      /* 0x00E */
  60 #define OPC_INB_SSP_ABORT                       15      /* 0x00F */
  61 #define OPC_INB_DEREG_DEV_HANDLE                16      /* 0x010 */
  62 #define OPC_INB_GET_DEV_HANDLE                  17      /* 0x011 */
  63 #define OPC_INB_SMP_REQUEST                     18      /* 0x012 */
  64 /* SMP_RESPONSE is removed */
  65 #define OPC_INB_SMP_RESPONSE                    19      /* 0x013 */
  66 #define OPC_INB_SMP_ABORT                       20      /* 0x014 */
  67 #define OPC_INB_REG_DEV                         22      /* 0x016 */
  68 #define OPC_INB_SATA_HOST_OPSTART               23      /* 0x017 */
  69 #define OPC_INB_SATA_ABORT                      24      /* 0x018 */
  70 #define OPC_INB_LOCAL_PHY_CONTROL               25      /* 0x019 */
  71 #define OPC_INB_GET_DEV_INFO                    26      /* 0x01A */
  72 #define OPC_INB_FW_FLASH_UPDATE                 32      /* 0x020 */
  73 #define OPC_INB_GPIO                            34      /* 0x022 */
  74 #define OPC_INB_SAS_DIAG_MODE_START_END         35      /* 0x023 */
  75 #define OPC_INB_SAS_DIAG_EXECUTE                36      /* 0x024 */
  76 #define OPC_INB_SAS_HW_EVENT_ACK                37      /* 0x025 */
  77 #define OPC_INB_GET_TIME_STAMP                  38      /* 0x026 */
  78 #define OPC_INB_PORT_CONTROL                    39      /* 0x027 */
  79 #define OPC_INB_GET_NVMD_DATA                   40      /* 0x028 */
  80 #define OPC_INB_SET_NVMD_DATA                   41      /* 0x029 */
  81 #define OPC_INB_SET_DEVICE_STATE                42      /* 0x02A */
  82 #define OPC_INB_GET_DEVICE_STATE                43      /* 0x02B */
  83 #define OPC_INB_SET_DEV_INFO                    44      /* 0x02C */
  84 #define OPC_INB_SAS_RE_INITIALIZE               45      /* 0x02D */
  85
  86 /* for Response Opcode of IOMB */
  87 #define OPC_OUB_ECHO                            1       /* 0x001 */
  88 #define OPC_OUB_HW_EVENT                        4       /* 0x004 */
  89 #define OPC_OUB_SSP_COMP                        5       /* 0x005 */
  90 #define OPC_OUB_SMP_COMP                        6       /* 0x006 */
  91 #define OPC_OUB_LOCAL_PHY_CNTRL                 7       /* 0x007 */
  92 #define OPC_OUB_DEV_REGIST                      10      /* 0x00A */
  93 #define OPC_OUB_DEREG_DEV                       11      /* 0x00B */
  94 #define OPC_OUB_GET_DEV_HANDLE                  12      /* 0x00C */
  95 #define OPC_OUB_SATA_COMP                       13      /* 0x00D */
  96 #define OPC_OUB_SATA_EVENT                      14      /* 0x00E */
  97 #define OPC_OUB_SSP_EVENT                       15      /* 0x00F */
  98 #define OPC_OUB_DEV_HANDLE_ARRIV                16      /* 0x010 */
  99 /* SMP_RECEIVED Notification is removed */
 100 #define OPC_OUB_SMP_RECV_EVENT                  17      /* 0x011 */
 101 #define OPC_OUB_SSP_RECV_EVENT                  18      /* 0x012 */
 102 #define OPC_OUB_DEV_INFO                        19      /* 0x013 */
 103 #define OPC_OUB_FW_FLASH_UPDATE                 20      /* 0x014 */
 104 #define OPC_OUB_GPIO_RESPONSE                   22      /* 0x016 */
 105 #define OPC_OUB_GPIO_EVENT                      23      /* 0x017 */
 106 #define OPC_OUB_GENERAL_EVENT                   24      /* 0x018 */
 107 #define OPC_OUB_SSP_ABORT_RSP                   26      /* 0x01A */
 108 #define OPC_OUB_SATA_ABORT_RSP                  27      /* 0x01B */
 109 #define OPC_OUB_SAS_DIAG_MODE_START_END         28      /* 0x01C */
 110 #define OPC_OUB_SAS_DIAG_EXECUTE                29      /* 0x01D */
 111 #define OPC_OUB_GET_TIME_STAMP                  30      /* 0x01E */
 112 #define OPC_OUB_SAS_HW_EVENT_ACK                31      /* 0x01F */
 113 #define OPC_OUB_PORT_CONTROL                    32      /* 0x020 */
 114 #define OPC_OUB_SKIP_ENTRY                      33      /* 0x021 */
 115 #define OPC_OUB_SMP_ABORT_RSP                   34      /* 0x022 */
 116 #define OPC_OUB_GET_NVMD_DATA                   35      /* 0x023 */
 117 #define OPC_OUB_SET_NVMD_DATA                   36      /* 0x024 */
 118 #define OPC_OUB_DEVICE_HANDLE_REMOVAL           37      /* 0x025 */
 119 #define OPC_OUB_SET_DEVICE_STATE                38      /* 0x026 */
 120 #define OPC_OUB_GET_DEVICE_STATE                39      /* 0x027 */
 121 #define OPC_OUB_SET_DEV_INFO                    40      /* 0x028 */
 122 #define OPC_OUB_SAS_RE_INITIALIZE               41      /* 0x029 */
 123
 124 /* for phy start*/
 125 #define SPINHOLD_DISABLE                (0x00 << 14)
 126 #define SPINHOLD_ENABLE                 (0x01 << 14)
 127 #define LINKMODE_SAS                    (0x01 << 12)
 128 #define LINKMODE_DSATA                  (0x02 << 12)
 129 #define LINKMODE_AUTO                   (0x03 << 12)
 130 #define LINKRATE_15                     (0x01 << 8)
 131 #define LINKRATE_30                     (0x02 << 8)
 132 #define LINKRATE_60                     (0x04 << 8)
 133
 134 struct mpi_msg_hdr{
 135         __le32  header; /* Bits [11:0]  - Message operation code */
 136         /* Bits [15:12] - Message Category */
 137         /* Bits [21:16] - Outboundqueue ID for the
 138         operation completion message */
 139         /* Bits [23:22] - Reserved */
 140         /* Bits [28:24] - Buffer Count, indicates how
 141         many buffer are allocated for the massage */
 142         /* Bits [30:29] - Reserved */
 143         /* Bits [31] - Message Valid bit */
 144 } __attribute__((packed, aligned(4)));
 145
 146
 147 /*
 148  * brief the data structure of PHY Start Command
 149  * use to describe enable the phy (64 bytes)
 150  */
 151 struct phy_start_req {
 152         __le32  tag;
 153         __le32  ase_sh_lm_slr_phyid;
 154         struct sas_identify_frame sas_identify;
 155         u32     reserved[5];
 156 } __attribute__((packed, aligned(4)));
 157
 158
 159 /*
 160  * brief the data structure of PHY Start Command
 161  * use to disable the phy (64 bytes)
 162  */
 163 struct phy_stop_req {
 164         __le32  tag;
 165         __le32  phy_id;
 166         u32     reserved[13];
 167 } __attribute__((packed, aligned(4)));
 168
 169
 170 /* set device bits fis - device to host */
 171 struct  set_dev_bits_fis {
 172         u8      fis_type;       /* 0xA1*/
 173         u8      n_i_pmport;
 174         /* b7 : n Bit. Notification bit. If set device needs attention. */
 175         /* b6 : i Bit. Interrupt Bit */
 176         /* b5-b4: reserved2 */
 177         /* b3-b0: PM Port */
 178         u8      status;
 179         u8      error;
 180         u32     _r_a;
 181 } __attribute__ ((packed));
 182 /* PIO setup FIS - device to host */
 183 struct  pio_setup_fis {
 184         u8      fis_type;       /* 0x5f */
 185         u8      i_d_pmPort;
 186         /* b7 : reserved */
 187         /* b6 : i bit. Interrupt bit */
 188         /* b5 : d bit. data transfer direction. set to 1 for device to host
 189         xfer */
 190         /* b4 : reserved */
 191         /* b3-b0: PM Port */
 192         u8      status;
 193         u8      error;
 194         u8      lbal;
 195         u8      lbam;
 196         u8      lbah;
 197         u8      device;
 198         u8      lbal_exp;
 199         u8      lbam_exp;
 200         u8      lbah_exp;
 201         u8      _r_a;
 202         u8      sector_count;
 203         u8      sector_count_exp;
 204         u8      _r_b;
 205         u8      e_status;
 206         u8      _r_c[2];
 207         u8      transfer_count;
 208 } __attribute__ ((packed));
 209
 210 /*
 211  * brief the data structure of SATA Completion Response
 212  * use to describe the sata task response (64 bytes)
 213  */
 214 struct sata_completion_resp {
 215         __le32  tag;
 216         __le32  status;
 217         __le32  param;
 218         u32     sata_resp[12];
 219 } __attribute__((packed, aligned(4)));
 220
 221
 222 /*
 223  * brief the data structure of SAS HW Event Notification
 224  * use to alert the host about the hardware event(64 bytes)
 225  */
 226 struct hw_event_resp {
 227         __le32  lr_evt_status_phyid_portid;
 228         __le32  evt_param;
 229         __le32  npip_portstate;
 230         struct sas_identify_frame       sas_identify;
 231         struct dev_to_host_fis  sata_fis;
 232 } __attribute__((packed, aligned(4)));
 233
 234
 235 /*
 236  * brief the data structure of  REGISTER DEVICE Command
 237  * use to describe MPI REGISTER DEVICE Command (64 bytes)
 238  */
 239
 240 struct reg_dev_req {
 241         __le32  tag;
 242         __le32  phyid_portid;
 243         __le32  dtype_dlr_retry;
 244         __le32  firstburstsize_ITNexustimeout;
 245         u8      sas_addr[SAS_ADDR_SIZE];
 246         __le32  upper_device_id;
 247         u32     reserved[8];
 248 } __attribute__((packed, aligned(4)));
 249
 250
 251 /*
 252  * brief the data structure of  DEREGISTER DEVICE Command
 253  * use to request spc to remove all internal resources associated
 254  * with the device id (64 bytes)
 255  */
 256
 257 struct dereg_dev_req {
 258         __le32  tag;
 259         __le32  device_id;
 260         u32     reserved[13];
 261 } __attribute__((packed, aligned(4)));
 262
 263
 264 /*
 265  * brief the data structure of DEVICE_REGISTRATION Response
 266  * use to notify the completion of the device registration  (64 bytes)
 267  */
 268
 269 struct dev_reg_resp {
 270         __le32  tag;
 271         __le32  status;
 272         __le32  device_id;
 273         u32     reserved[12];
 274 } __attribute__((packed, aligned(4)));
 275
 276
 277 /*
 278  * brief the data structure of Local PHY Control Command
 279  * use to issue PHY CONTROL to local phy (64 bytes)
 280  */
 281 struct local_phy_ctl_req {
 282         __le32  tag;
 283         __le32  phyop_phyid;
 284         u32     reserved1[13];
 285 } __attribute__((packed, aligned(4)));
 286
 287
 288 /**
 289  * brief the data structure of Local Phy Control Response
 290  * use to describe MPI Local Phy Control Response (64 bytes)
 291  */
 292 struct local_phy_ctl_resp {
 293         __le32  tag;
 294         __le32  phyop_phyid;
 295         __le32  status;
 296         u32     reserved[12];
 297 } __attribute__((packed, aligned(4)));
 298
 299
 300 #define OP_BITS 0x0000FF00
 301 #define ID_BITS 0x0000000F
 302
 303 /*
 304  * brief the data structure of PORT Control Command
 305  * use to control port properties (64 bytes)
 306  */
 307
 308 struct port_ctl_req {
 309         __le32  tag;
 310         __le32  portop_portid;
 311         __le32  param0;
 312         __le32  param1;
 313         u32     reserved1[11];
 314 } __attribute__((packed, aligned(4)));
 315
 316
 317 /*
 318  * brief the data structure of HW Event Ack Command
 319  * use to acknowledge receive HW event (64 bytes)
 320  */
 321
 322 struct hw_event_ack_req {
 323         __le32  tag;
 324         __le32  sea_phyid_portid;
 325         __le32  param0;
 326         __le32  param1;
 327         u32     reserved1[11];
 328 } __attribute__((packed, aligned(4)));
 329
 330
 331 /*
 332  * brief the data structure of SSP Completion Response
 333  * use to indicate a SSP Completion  (n bytes)
 334  */
 335 struct ssp_completion_resp {
 336         __le32  tag;
 337         __le32  status;
 338         __le32  param;
 339         __le32  ssptag_rescv_rescpad;
 340         struct ssp_response_iu  ssp_resp_iu;
 341         __le32  residual_count;
 342 } __attribute__((packed, aligned(4)));
 343
 344
 345 #define SSP_RESCV_BIT   0x00010000
 346
 347 /*
 348  * brief the data structure of SATA EVNET esponse
 349  * use to indicate a SATA Completion  (64 bytes)
 350  */
 351
 352 struct sata_event_resp {
 353         __le32  tag;
 354         __le32  event;
 355         __le32  port_id;
 356         __le32  device_id;
 357         u32     reserved[11];
 358 } __attribute__((packed, aligned(4)));
 359
 360 /*
 361  * brief the data structure of SSP EVNET esponse
 362  * use to indicate a SSP Completion  (64 bytes)
 363  */
 364
 365 struct ssp_event_resp {
 366         __le32  tag;
 367         __le32  event;
 368         __le32  port_id;
 369         __le32  device_id;
 370         u32     reserved[11];
 371 } __attribute__((packed, aligned(4)));
 372
 373 /**
 374  * brief the data structure of General Event Notification Response
 375  * use to describe MPI General Event Notification Response (64 bytes)
 376  */
 377 struct general_event_resp {
 378         __le32  status;
 379         __le32  inb_IOMB_payload[14];
 380 } __attribute__((packed, aligned(4)));
 381
 382
 383 #define GENERAL_EVENT_PAYLOAD   14
 384 #define OPCODE_BITS     0x00000fff
 385
 386 /*
 387  * brief the data structure of SMP Request Command
 388  * use to describe MPI SMP REQUEST Command (64 bytes)
 389  */
 390 struct smp_req {
 391         __le32  tag;
 392         __le32  device_id;
 393         __le32  len_ip_ir;
 394         /* Bits [0]  - Indirect response */
 395         /* Bits [1] - Indirect Payload */
 396         /* Bits [15:2] - Reserved */
 397         /* Bits [23:16] - direct payload Len */
 398         /* Bits [31:24] - Reserved */
 399         u8      smp_req16[16];
 400         union {
 401                 u8      smp_req[32];
 402                 struct {
 403                         __le64 long_req_addr;/* sg dma address, LE */
 404                         __le32 long_req_size;/* LE */
 405                         u32     _r_a;
 406                         __le64 long_resp_addr;/* sg dma address, LE */
 407                         __le32 long_resp_size;/* LE */
 408                         u32     _r_b;
 409                         } long_smp_req;/* sequencer extension */
 410         };
 411 } __attribute__((packed, aligned(4)));
 412 /*
 413  * brief the data structure of SMP Completion Response
 414  * use to describe MPI SMP Completion Response (64 bytes)
 415  */
 416 struct smp_completion_resp {
 417         __le32  tag;
 418         __le32  status;
 419         __le32  param;
 420         __le32  _r_a[12];
 421 } __attribute__((packed, aligned(4)));
 422
 423 /*
 424  *brief the data structure of SSP SMP SATA Abort Command
 425  * use to describe MPI SSP SMP & SATA Abort Command (64 bytes)
 426  */
 427 struct task_abort_req {
 428         __le32  tag;
 429         __le32  device_id;
 430         __le32  tag_to_abort;
 431         __le32  abort_all;
 432         u32     reserved[11];
 433 } __attribute__((packed, aligned(4)));
 434
 435 /* These flags used for SSP SMP & SATA Abort */
 436 #define ABORT_MASK              0x3
 437 #define ABORT_SINGLE            0x0
 438 #define ABORT_ALL               0x1
 439
 440 /**
 441  * brief the data structure of SSP SATA SMP Abort Response
 442  * use to describe SSP SMP & SATA Abort Response ( 64 bytes)
 443  */
 444 struct task_abort_resp {
 445         __le32  tag;
 446         __le32  status;
 447         __le32  scp;
 448         u32     reserved[12];
 449 } __attribute__((packed, aligned(4)));
 450
 451
 452 /**
 453  * brief the data structure of SAS Diagnostic Start/End Command
 454  * use to describe MPI SAS Diagnostic Start/End Command (64 bytes)
 455  */
 456 struct sas_diag_start_end_req {
 457         __le32  tag;
 458         __le32  operation_phyid;
 459         u32     reserved[13];
 460 } __attribute__((packed, aligned(4)));
 461
 462
 463 /**
 464  * brief the data structure of SAS Diagnostic Execute Command
 465  * use to describe MPI SAS Diagnostic Execute Command (64 bytes)
 466  */
 467 struct sas_diag_execute_req{
 468         __le32  tag;
 469         __le32  cmdtype_cmddesc_phyid;
 470         __le32  pat1_pat2;
 471         __le32  threshold;
 472         __le32  codepat_errmsk;
 473         __le32  pmon;
 474         __le32  pERF1CTL;
 475         u32     reserved[8];
 476 } __attribute__((packed, aligned(4)));
 477
 478
 479 #define SAS_DIAG_PARAM_BYTES 24
 480
 481 /*
 482  * brief the data structure of Set Device State Command
 483  * use to describe MPI Set Device State Command (64 bytes)
 484  */
 485 struct set_dev_state_req {
 486         __le32  tag;
 487         __le32  device_id;
 488         __le32  nds;
 489         u32     reserved[12];
 490 } __attribute__((packed, aligned(4)));
 491
 492 /*
 493  * brief the data structure of sas_re_initialization
 494  */
 495 struct sas_re_initialization_req {
 496
 497         __le32  tag;
 498         __le32  SSAHOLT;/* bit29-set max port;
 499                         ** bit28-set open reject cmd retries.
 500                         ** bit27-set open reject data retries.
 501                         ** bit26-set open reject option, remap:1 or not:0.
 502                         ** bit25-set sata head of line time out.
 503                         */
 504         __le32 reserved_maxPorts;
 505         __le32 open_reject_cmdretries_data_retries;/* cmd retries: 31-bit16;
 506                                                     * data retries: bit15-bit0.
 507                                                     */
 508         __le32  sata_hol_tmo;
 509         u32     reserved1[10];
 510 } __attribute__((packed, aligned(4)));
 511
 512 /*
 513  * brief the data structure of SATA Start Command
 514  * use to describe MPI SATA IO Start Command (64 bytes)
 515  */
 516
 517 struct sata_start_req {
 518         __le32  tag;
 519         __le32  device_id;
 520         __le32  data_len;
 521         __le32  ncqtag_atap_dir_m;
 522         struct host_to_dev_fis  sata_fis;
 523         u32     reserved1;
 524         u32     reserved2;
 525         u32     addr_low;
 526         u32     addr_high;
 527         __le32  len;
 528         __le32  esgl;
 529 } __attribute__((packed, aligned(4)));
 530
 531 /**
 532  * brief the data structure of SSP INI TM Start Command
 533  * use to describe MPI SSP INI TM Start Command (64 bytes)
 534  */
 535 struct ssp_ini_tm_start_req {
 536         __le32  tag;
 537         __le32  device_id;
 538         __le32  relate_tag;
 539         __le32  tmf;
 540         u8      lun[8];
 541         __le32  ds_ads_m;
 542         u32     reserved[8];
 543 } __attribute__((packed, aligned(4)));
 544
 545
 546 struct ssp_info_unit {
 547         u8      lun[8];/* SCSI Logical Unit Number */
 548         u8      reserved1;/* reserved */
 549         u8      efb_prio_attr;
 550         /* B7   : enabledFirstBurst */
 551         /* B6-3 : taskPriority */
 552         /* B2-0 : taskAttribute */
 553         u8      reserved2;      /* reserved */
 554         u8      additional_cdb_len;
 555         /* B7-2 : additional_cdb_len */
 556         /* B1-0 : reserved */
 557         u8      cdb[16];/* The SCSI CDB up to 16 bytes length */
 558 } __attribute__((packed, aligned(4)));
 559
 560
 561 /**
 562  * brief the data structure of SSP INI IO Start Command
 563  * use to describe MPI SSP INI IO Start Command (64 bytes)
 564  */
 565 struct ssp_ini_io_start_req {
 566         __le32  tag;
 567         __le32  device_id;
 568         __le32  data_len;
 569         __le32  dir_m_tlr;
 570         struct ssp_info_unit    ssp_iu;
 571         __le32  addr_low;
 572         __le32  addr_high;
 573         __le32  len;
 574         __le32  esgl;
 575 } __attribute__((packed, aligned(4)));
 576
 577
 578 /**
 579  * brief the data structure of Firmware download
 580  * use to describe MPI FW DOWNLOAD Command (64 bytes)
 581  */
 582 struct fw_flash_Update_req {
 583         __le32  tag;
 584         __le32  cur_image_offset;
 585         __le32  cur_image_len;
 586         __le32  total_image_len;
 587         u32     reserved0[7];
 588         __le32  sgl_addr_lo;
 589         __le32  sgl_addr_hi;
 590         __le32  len;
 591         __le32  ext_reserved;
 592 } __attribute__((packed, aligned(4)));
 593
 594
 595 #define FWFLASH_IOMB_RESERVED_LEN 0x07
 596 /**
 597  * brief the data structure of FW_FLASH_UPDATE Response
 598  * use to describe MPI FW_FLASH_UPDATE Response (64 bytes)
 599  *
 600  */
 601 struct fw_flash_Update_resp {
 602         dma_addr_t      tag;
 603         __le32  status;
 604         u32     reserved[13];
 605 } __attribute__((packed, aligned(4)));
 606
 607
 608 /**
 609  * brief the data structure of Get NVM Data Command
 610  * use to get data from NVM in HBA(64 bytes)
 611  */
 612 struct get_nvm_data_req {
 613         __le32  tag;
 614         __le32  len_ir_vpdd;
 615         __le32  vpd_offset;
 616         u32     reserved[8];
 617         __le32  resp_addr_lo;
 618         __le32  resp_addr_hi;
 619         __le32  resp_len;
 620         u32     reserved1;
 621 } __attribute__((packed, aligned(4)));
 622
 623
 624 struct set_nvm_data_req {
 625         __le32  tag;
 626         __le32  len_ir_vpdd;
 627         __le32  vpd_offset;
 628         u32     reserved[8];
 629         __le32  resp_addr_lo;
 630         __le32  resp_addr_hi;
 631         __le32  resp_len;
 632         u32     reserved1;
 633 } __attribute__((packed, aligned(4)));
 634
 635
 636 #define TWI_DEVICE      0x0
 637 #define C_SEEPROM       0x1
 638 #define VPD_FLASH       0x4
 639 #define AAP1_RDUMP      0x5
 640 #define IOP_RDUMP       0x6
 641 #define EXPAN_ROM       0x7
 642
 643 #define IPMode          0x80000000
 644 #define NVMD_TYPE       0x0000000F
 645 #define NVMD_STAT       0x0000FFFF
 646 #define NVMD_LEN        0xFF000000
 647 /**
 648  * brief the data structure of Get NVMD Data Response
 649  * use to describe MPI Get NVMD Data Response (64 bytes)
 650  */
 651 struct get_nvm_data_resp {
 652         __le32          tag;
 653         __le32          ir_tda_bn_dps_das_nvm;
 654         __le32          dlen_status;
 655         __le32          nvm_data[12];
 656 } __attribute__((packed, aligned(4)));
 657
 658
 659 /**
 660  * brief the data structure of SAS Diagnostic Start/End Response
 661  * use to describe MPI SAS Diagnostic Start/End Response (64 bytes)
 662  *
 663  */
 664 struct sas_diag_start_end_resp {
 665         __le32          tag;
 666         __le32          status;
 667         u32             reserved[13];
 668 } __attribute__((packed, aligned(4)));
 669
 670
 671 /**
 672  * brief the data structure of SAS Diagnostic Execute Response
 673  * use to describe MPI SAS Diagnostic Execute Response (64 bytes)
 674  *
 675  */
 676 struct sas_diag_execute_resp {
 677         __le32          tag;
 678         __le32          cmdtype_cmddesc_phyid;
 679         __le32          Status;
 680         __le32          ReportData;
 681         u32             reserved[11];
 682 } __attribute__((packed, aligned(4)));
 683
 684
 685 /**
 686  * brief the data structure of Set Device State Response
 687  * use to describe MPI Set Device State Response (64 bytes)
 688  *
 689  */
 690 struct set_dev_state_resp {
 691         __le32          tag;
 692         __le32          status;
 693         __le32          device_id;
 694         __le32          pds_nds;
 695         u32             reserved[11];
 696 } __attribute__((packed, aligned(4)));
 697
 698
 699 #define NDS_BITS 0x0F
 700 #define PDS_BITS 0xF0
 701
 702 /*
 703  * HW Events type
 704  */
 705
 706 #define HW_EVENT_RESET_START                    0x01
 707 #define HW_EVENT_CHIP_RESET_COMPLETE            0x02
 708 #define HW_EVENT_PHY_STOP_STATUS                0x03
 709 #define HW_EVENT_SAS_PHY_UP                     0x04
 710 #define HW_EVENT_SATA_PHY_UP                    0x05
 711 #define HW_EVENT_SATA_SPINUP_HOLD               0x06
 712 #define HW_EVENT_PHY_DOWN                       0x07
 713 #define HW_EVENT_PORT_INVALID                   0x08
 714 #define HW_EVENT_BROADCAST_CHANGE               0x09
 715 #define HW_EVENT_PHY_ERROR                      0x0A
 716 #define HW_EVENT_BROADCAST_SES                  0x0B
 717 #define HW_EVENT_INBOUND_CRC_ERROR              0x0C
 718 #define HW_EVENT_HARD_RESET_RECEIVED            0x0D
 719 #define HW_EVENT_MALFUNCTION                    0x0E
 720 #define HW_EVENT_ID_FRAME_TIMEOUT               0x0F
 721 #define HW_EVENT_BROADCAST_EXP                  0x10
 722 #define HW_EVENT_PHY_START_STATUS               0x11
 723 #define HW_EVENT_LINK_ERR_INVALID_DWORD         0x12
 724 #define HW_EVENT_LINK_ERR_DISPARITY_ERROR       0x13
 725 #define HW_EVENT_LINK_ERR_CODE_VIOLATION        0x14
 726 #define HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH   0x15
 727 #define HW_EVENT_LINK_ERR_PHY_RESET_FAILED      0x16
 728 #define HW_EVENT_PORT_RECOVERY_TIMER_TMO        0x17
 729 #define HW_EVENT_PORT_RECOVER                   0x18
 730 #define HW_EVENT_PORT_RESET_TIMER_TMO           0x19
 731 #define HW_EVENT_PORT_RESET_COMPLETE            0x20
 732 #define EVENT_BROADCAST_ASYNCH_EVENT            0x21
 733
 734 /* port state */
 735 #define PORT_NOT_ESTABLISHED                    0x00
 736 #define PORT_VALID                              0x01
 737 #define PORT_LOSTCOMM                           0x02
 738 #define PORT_IN_RESET                           0x04
 739 #define PORT_INVALID                            0x08
 740
 741 /*
 742  * SSP/SMP/SATA IO Completion Status values
 743  */
 744
 745 #define IO_SUCCESS                              0x00
 746 #define IO_ABORTED                              0x01
 747 #define IO_OVERFLOW                             0x02
 748 #define IO_UNDERFLOW                            0x03
 749 #define IO_FAILED                               0x04
 750 #define IO_ABORT_RESET                          0x05
 751 #define IO_NOT_VALID                            0x06
 752 #define IO_NO_DEVICE                            0x07
 753 #define IO_ILLEGAL_PARAMETER                    0x08
 754 #define IO_LINK_FAILURE                         0x09
 755 #define IO_PROG_ERROR                           0x0A
 756 #define IO_EDC_IN_ERROR                         0x0B
 757 #define IO_EDC_OUT_ERROR                        0x0C
 758 #define IO_ERROR_HW_TIMEOUT                     0x0D
 759 #define IO_XFER_ERROR_BREAK                     0x0E
 760 #define IO_XFER_ERROR_PHY_NOT_READY             0x0F
 761 #define IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED        0x10
 762 #define IO_OPEN_CNX_ERROR_ZONE_VIOLATION                0x11
 763 #define IO_OPEN_CNX_ERROR_BREAK                         0x12
 764 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS                 0x13
 765 #define IO_OPEN_CNX_ERROR_BAD_DESTINATION               0x14
 766 #define IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED 0x15
 767 #define IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY            0x16
 768 #define IO_OPEN_CNX_ERROR_WRONG_DESTINATION             0x17
 769 #define IO_OPEN_CNX_ERROR_UNKNOWN_ERROR                 0x18
 770 #define IO_XFER_ERROR_NAK_RECEIVED                      0x19
 771 #define IO_XFER_ERROR_ACK_NAK_TIMEOUT                   0x1A
 772 #define IO_XFER_ERROR_PEER_ABORTED                      0x1B
 773 #define IO_XFER_ERROR_RX_FRAME                          0x1C
 774 #define IO_XFER_ERROR_DMA                               0x1D
 775 #define IO_XFER_ERROR_CREDIT_TIMEOUT                    0x1E
 776 #define IO_XFER_ERROR_SATA_LINK_TIMEOUT                 0x1F
 777 #define IO_XFER_ERROR_SATA                              0x20
 778 #define IO_XFER_ERROR_ABORTED_DUE_TO_SRST               0x22
 779 #define IO_XFER_ERROR_REJECTED_NCQ_MODE                 0x21
 780 #define IO_XFER_ERROR_ABORTED_NCQ_MODE                  0x23
 781 #define IO_XFER_OPEN_RETRY_TIMEOUT                      0x24
 782 #define IO_XFER_SMP_RESP_CONNECTION_ERROR               0x25
 783 #define IO_XFER_ERROR_UNEXPECTED_PHASE                  0x26
 784 #define IO_XFER_ERROR_XFER_RDY_OVERRUN                  0x27
 785 #define IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED             0x28
 786
 787 #define IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT         0x30
 788 #define IO_XFER_ERROR_CMD_ISSUE_BREAK_BEFORE_ACK_NAK    0x31
 789 #define IO_XFER_ERROR_CMD_ISSUE_PHY_DOWN_BEFORE_ACK_NAK 0x32
 790
 791 #define IO_XFER_ERROR_OFFSET_MISMATCH                   0x34
 792 #define IO_XFER_ERROR_XFER_ZERO_DATA_LEN                0x35
 793 #define IO_XFER_CMD_FRAME_ISSUED                        0x36
 794 #define IO_ERROR_INTERNAL_SMP_RESOURCE                  0x37
 795 #define IO_PORT_IN_RESET                                0x38
 796 #define IO_DS_NON_OPERATIONAL                           0x39
 797 #define IO_DS_IN_RECOVERY                               0x3A
 798 #define IO_TM_TAG_NOT_FOUND                             0x3B
 799 #define IO_XFER_PIO_SETUP_ERROR                         0x3C
 800 #define IO_SSP_EXT_IU_ZERO_LEN_ERROR                    0x3D
 801 #define IO_DS_IN_ERROR                                  0x3E
 802 #define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY              0x3F
 803 #define IO_ABORT_IN_PROGRESS                            0x40
 804 #define IO_ABORT_DELAYED                                0x41
 805 #define IO_INVALID_LENGTH                               0x42
 806
 807 /* WARNING: This error code must always be the last number.
 808  * If you add error code, modify this code also
 809  * It is used as an index
 810  */
 811 #define IO_ERROR_UNKNOWN_GENERIC                        0x43
 812
 813 /* MSGU CONFIGURATION  TABLE*/
 814
 815 #define SPC_MSGU_CFG_TABLE_UPDATE               0x01/* Inbound doorbell bit0 */
 816 #define SPC_MSGU_CFG_TABLE_RESET                0x02/* Inbound doorbell bit1 */
 817 #define SPC_MSGU_CFG_TABLE_FREEZE               0x04/* Inbound doorbell bit2 */
 818 #define SPC_MSGU_CFG_TABLE_UNFREEZE             0x08/* Inbound doorbell bit4 */
 819 #define MSGU_IBDB_SET                           0x04
 820 #define MSGU_HOST_INT_STATUS                    0x08
 821 #define MSGU_HOST_INT_MASK                      0x0C
 822 #define MSGU_IOPIB_INT_STATUS                   0x18
 823 #define MSGU_IOPIB_INT_MASK                     0x1C
 824 #define MSGU_IBDB_CLEAR                         0x20/* RevB - Host not use */
 825 #define MSGU_MSGU_CONTROL                       0x24
 826 #define MSGU_ODR                                0x3C/* RevB */
 827 #define MSGU_ODCR                               0x40/* RevB */
 828 #define MSGU_SCRATCH_PAD_0                      0x44
 829 #define MSGU_SCRATCH_PAD_1                      0x48
 830 #define MSGU_SCRATCH_PAD_2                      0x4C
 831 #define MSGU_SCRATCH_PAD_3                      0x50
 832 #define MSGU_HOST_SCRATCH_PAD_0                 0x54
 833 #define MSGU_HOST_SCRATCH_PAD_1                 0x58
 834 #define MSGU_HOST_SCRATCH_PAD_2                 0x5C
 835 #define MSGU_HOST_SCRATCH_PAD_3                 0x60
 836 #define MSGU_HOST_SCRATCH_PAD_4                 0x64
 837 #define MSGU_HOST_SCRATCH_PAD_5                 0x68
 838 #define MSGU_HOST_SCRATCH_PAD_6                 0x6C
 839 #define MSGU_HOST_SCRATCH_PAD_7                 0x70
 840 #define MSGU_ODMR                               0x74/* RevB */
 841
 842 /* bit definition for ODMR register */
 843 #define ODMR_MASK_ALL                           0xFFFFFFFF/* mask all
 844                                         interrupt vector */
 845 #define ODMR_CLEAR_ALL                          0/* clear all
 846                                         interrupt vector */
 847 /* bit definition for ODCR register */
 848 #define ODCR_CLEAR_ALL          0xFFFFFFFF   /* mask all
 849                                         interrupt vector*/
 850 /* MSIX Interupts */
 851 #define MSIX_TABLE_OFFSET               0x2000
 852 #define MSIX_TABLE_ELEMENT_SIZE         0x10
 853 #define MSIX_INTERRUPT_CONTROL_OFFSET   0xC
 854 #define MSIX_TABLE_BASE   (MSIX_TABLE_OFFSET + MSIX_INTERRUPT_CONTROL_OFFSET)
 855 #define MSIX_INTERRUPT_DISABLE          0x1
 856 #define MSIX_INTERRUPT_ENABLE           0x0
 857
 858
 859 /* state definition for Scratch Pad1 register */
 860 #define SCRATCH_PAD1_POR                0x00  /* power on reset state */
 861 #define SCRATCH_PAD1_SFR                0x01  /* soft reset state */
 862 #define SCRATCH_PAD1_ERR                0x02  /* error state */
 863 #define SCRATCH_PAD1_RDY                0x03  /* ready state */
 864 #define SCRATCH_PAD1_RST                0x04  /* soft reset toggle flag */
 865 #define SCRATCH_PAD1_AAP1RDY_RST        0x08  /* AAP1 ready for soft reset */
 866 #define SCRATCH_PAD1_STATE_MASK         0xFFFFFFF0   /* ScratchPad1
 867  Mask, bit1-0 State, bit2 Soft Reset, bit3 FW RDY for Soft Reset */
 868 #define SCRATCH_PAD1_RESERVED           0x000003F8   /* Scratch Pad1
 869  Reserved bit 3 to 9 */
 870
 871  /* state definition for Scratch Pad2 register */
 872 #define SCRATCH_PAD2_POR                0x00  /* power on state */
 873 #define SCRATCH_PAD2_SFR                0x01  /* soft reset state */
 874 #define SCRATCH_PAD2_ERR                0x02  /* error state */
 875 #define SCRATCH_PAD2_RDY                0x03  /* ready state */
 876 #define SCRATCH_PAD2_FWRDY_RST          0x04  /* FW ready for soft reset flag*/
 877 #define SCRATCH_PAD2_IOPRDY_RST         0x08  /* IOP ready for soft reset */
 878 #define SCRATCH_PAD2_STATE_MASK         0xFFFFFFF4 /* ScratchPad 2
 879  Mask, bit1-0 State */
 880 #define SCRATCH_PAD2_RESERVED           0x000003FC   /* Scratch Pad1
 881  Reserved bit 2 to 9 */
 882
 883 #define SCRATCH_PAD_ERROR_MASK          0xFFFFFC00   /* Error mask bits */
 884 #define SCRATCH_PAD_STATE_MASK          0x00000003   /* State Mask bits */
 885
 886 /* main configuration offset - byte offset */
 887 #define MAIN_SIGNATURE_OFFSET           0x00/* DWORD 0x00 */
 888 #define MAIN_INTERFACE_REVISION         0x04/* DWORD 0x01 */
 889 #define MAIN_FW_REVISION                0x08/* DWORD 0x02 */
 890 #define MAIN_MAX_OUTSTANDING_IO_OFFSET  0x0C/* DWORD 0x03 */
 891 #define MAIN_MAX_SGL_OFFSET             0x10/* DWORD 0x04 */
 892 #define MAIN_CNTRL_CAP_OFFSET           0x14/* DWORD 0x05 */
 893 #define MAIN_GST_OFFSET                 0x18/* DWORD 0x06 */
 894 #define MAIN_IBQ_OFFSET                 0x1C/* DWORD 0x07 */
 895 #define MAIN_OBQ_OFFSET                 0x20/* DWORD 0x08 */
 896 #define MAIN_IQNPPD_HPPD_OFFSET         0x24/* DWORD 0x09 */
 897 #define MAIN_OB_HW_EVENT_PID03_OFFSET   0x28/* DWORD 0x0A */
 898 #define MAIN_OB_HW_EVENT_PID47_OFFSET   0x2C/* DWORD 0x0B */
 899 #define MAIN_OB_NCQ_EVENT_PID03_OFFSET  0x30/* DWORD 0x0C */
 900 #define MAIN_OB_NCQ_EVENT_PID47_OFFSET  0x34/* DWORD 0x0D */
 901 #define MAIN_TITNX_EVENT_PID03_OFFSET   0x38/* DWORD 0x0E */
 902 #define MAIN_TITNX_EVENT_PID47_OFFSET   0x3C/* DWORD 0x0F */
 903 #define MAIN_OB_SSP_EVENT_PID03_OFFSET  0x40/* DWORD 0x10 */
 904 #define MAIN_OB_SSP_EVENT_PID47_OFFSET  0x44/* DWORD 0x11 */
 905 #define MAIN_OB_SMP_EVENT_PID03_OFFSET  0x48/* DWORD 0x12 */
 906 #define MAIN_OB_SMP_EVENT_PID47_OFFSET  0x4C/* DWORD 0x13 */
 907 #define MAIN_EVENT_LOG_ADDR_HI          0x50/* DWORD 0x14 */
 908 #define MAIN_EVENT_LOG_ADDR_LO          0x54/* DWORD 0x15 */
 909 #define MAIN_EVENT_LOG_BUFF_SIZE        0x58/* DWORD 0x16 */
 910 #define MAIN_EVENT_LOG_OPTION           0x5C/* DWORD 0x17 */
 911 #define MAIN_IOP_EVENT_LOG_ADDR_HI      0x60/* DWORD 0x18 */
 912 #define MAIN_IOP_EVENT_LOG_ADDR_LO      0x64/* DWORD 0x19 */
 913 #define MAIN_IOP_EVENT_LOG_BUFF_SIZE    0x68/* DWORD 0x1A */
 914 #define MAIN_IOP_EVENT_LOG_OPTION       0x6C/* DWORD 0x1B */
 915 #define MAIN_FATAL_ERROR_INTERRUPT      0x70/* DWORD 0x1C */
 916 #define MAIN_FATAL_ERROR_RDUMP0_OFFSET  0x74/* DWORD 0x1D */
 917 #define MAIN_FATAL_ERROR_RDUMP0_LENGTH  0x78/* DWORD 0x1E */
 918 #define MAIN_FATAL_ERROR_RDUMP1_OFFSET  0x7C/* DWORD 0x1F */
 919 #define MAIN_FATAL_ERROR_RDUMP1_LENGTH  0x80/* DWORD 0x20 */
 920 #define MAIN_HDA_FLAGS_OFFSET           0x84/* DWORD 0x21 */
 921 #define MAIN_ANALOG_SETUP_OFFSET        0x88/* DWORD 0x22 */
 922
 923 /* Gereral Status Table offset - byte offset */
 924 #define GST_GSTLEN_MPIS_OFFSET          0x00
 925 #define GST_IQ_FREEZE_STATE0_OFFSET     0x04
 926 #define GST_IQ_FREEZE_STATE1_OFFSET     0x08
 927 #define GST_MSGUTCNT_OFFSET             0x0C
 928 #define GST_IOPTCNT_OFFSET              0x10
 929 #define GST_PHYSTATE_OFFSET             0x18
 930 #define GST_PHYSTATE0_OFFSET            0x18
 931 #define GST_PHYSTATE1_OFFSET            0x1C
 932 #define GST_PHYSTATE2_OFFSET            0x20
 933 #define GST_PHYSTATE3_OFFSET            0x24
 934 #define GST_PHYSTATE4_OFFSET            0x28
 935 #define GST_PHYSTATE5_OFFSET            0x2C
 936 #define GST_PHYSTATE6_OFFSET            0x30
 937 #define GST_PHYSTATE7_OFFSET            0x34
 938 #define GST_RERRINFO_OFFSET             0x44
 939
 940 /* General Status Table - MPI state */
 941 #define GST_MPI_STATE_UNINIT            0x00
 942 #define GST_MPI_STATE_INIT              0x01
 943 #define GST_MPI_STATE_TERMINATION       0x02
 944 #define GST_MPI_STATE_ERROR             0x03
 945 #define GST_MPI_STATE_MASK              0x07
 946
 947 #define MBIC_NMI_ENABLE_VPE0_IOP        0x000418
 948 #define MBIC_NMI_ENABLE_VPE0_AAP1       0x000418
 949 /* PCIE registers - BAR2(0x18), BAR1(win) 0x010000 */
 950 #define PCIE_EVENT_INTERRUPT_ENABLE     0x003040
 951 #define PCIE_EVENT_INTERRUPT            0x003044
 952 #define PCIE_ERROR_INTERRUPT_ENABLE     0x003048
 953 #define PCIE_ERROR_INTERRUPT            0x00304C
 954 /* signature definition for host scratch pad0 register */
 955 #define SPC_SOFT_RESET_SIGNATURE        0x252acbcd
 956 /* Signature for Soft Reset */
 957
 958 /* SPC Reset register - BAR4(0x20), BAR2(win) (need dynamic mapping) */
 959 #define SPC_REG_RESET                   0x000000/* reset register */
 960
 961 /* bit difination for SPC_RESET register */
 962 #define   SPC_REG_RESET_OSSP            0x00000001
 963 #define   SPC_REG_RESET_RAAE            0x00000002
 964 #define   SPC_REG_RESET_PCS_SPBC        0x00000004
 965 #define   SPC_REG_RESET_PCS_IOP_SS      0x00000008
 966 #define   SPC_REG_RESET_PCS_AAP1_SS     0x00000010
 967 #define   SPC_REG_RESET_PCS_AAP2_SS     0x00000020
 968 #define   SPC_REG_RESET_PCS_LM          0x00000040
 969 #define   SPC_REG_RESET_PCS             0x00000080
 970 #define   SPC_REG_RESET_GSM             0x00000100
 971 #define   SPC_REG_RESET_DDR2            0x00010000
 972 #define   SPC_REG_RESET_BDMA_CORE       0x00020000
 973 #define   SPC_REG_RESET_BDMA_SXCBI      0x00040000
 974 #define   SPC_REG_RESET_PCIE_AL_SXCBI   0x00080000
 975 #define   SPC_REG_RESET_PCIE_PWR        0x00100000
 976 #define   SPC_REG_RESET_PCIE_SFT        0x00200000
 977 #define   SPC_REG_RESET_PCS_SXCBI       0x00400000
 978 #define   SPC_REG_RESET_LMS_SXCBI       0x00800000
 979 #define   SPC_REG_RESET_PMIC_SXCBI      0x01000000
 980 #define   SPC_REG_RESET_PMIC_CORE       0x02000000
 981 #define   SPC_REG_RESET_PCIE_PC_SXCBI   0x04000000
 982 #define   SPC_REG_RESET_DEVICE          0x80000000
 983
 984 /* registers for BAR Shifting - BAR2(0x18), BAR1(win) */
 985 #define SPC_IBW_AXI_TRANSLATION_LOW     0x003258
 986
 987 #define MBIC_AAP1_ADDR_BASE             0x060000
 988 #define MBIC_IOP_ADDR_BASE              0x070000
 989 #define GSM_ADDR_BASE                   0x0700000
 990 /* Dynamic map through Bar4 - 0x00700000 */
 991 #define GSM_CONFIG_RESET                0x00000000
 992 #define RAM_ECC_DB_ERR                  0x00000018
 993 #define GSM_READ_ADDR_PARITY_INDIC      0x00000058
 994 #define GSM_WRITE_ADDR_PARITY_INDIC     0x00000060
 995 #define GSM_WRITE_DATA_PARITY_INDIC     0x00000068
 996 #define GSM_READ_ADDR_PARITY_CHECK      0x00000038
 997 #define GSM_WRITE_ADDR_PARITY_CHECK     0x00000040
 998 #define GSM_WRITE_DATA_PARITY_CHECK     0x00000048
 999
1000 #define RB6_ACCESS_REG                  0x6A0000
1001 #define HDAC_EXEC_CMD                   0x0002
1002 #define HDA_C_PA                        0xcb
1003 #define HDA_SEQ_ID_BITS                 0x00ff0000
1004 #define HDA_GSM_OFFSET_BITS             0x00FFFFFF
1005 #define MBIC_AAP1_ADDR_BASE             0x060000
1006 #define MBIC_IOP_ADDR_BASE              0x070000
1007 #define GSM_ADDR_BASE                   0x0700000
1008 #define SPC_TOP_LEVEL_ADDR_BASE         0x000000
1009 #define GSM_CONFIG_RESET_VALUE          0x00003b00
1010 #define GPIO_ADDR_BASE                  0x00090000
1011 #define GPIO_GPIO_0_0UTPUT_CTL_OFFSET   0x0000010c
1012
1013 /* RB6 offset */
1014 #define SPC_RB6_OFFSET                  0x80C0
1015 /* Magic number of  soft reset for RB6 */
1016 #define RB6_MAGIC_NUMBER_RST            0x1234
1017
1018 /* Device Register status */
1019 #define DEVREG_SUCCESS                                  0x00
1020 #define DEVREG_FAILURE_OUT_OF_RESOURCE                  0x01
1021 #define DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED        0x02
1022 #define DEVREG_FAILURE_INVALID_PHY_ID                   0x03
1023 #define DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED        0x04
1024 #define DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE             0x05
1025 #define DEVREG_FAILURE_PORT_NOT_VALID_STATE             0x06
1026 #define DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID            0x07
1027
1028 #endif
1029