?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
[linux/fpc-iii.git] / drivers / mmc / host / omap_hsmmc.c
blob0135693afa158420587976796dde940f0872fd65
1 /*
2 * drivers/mmc/host/omap_hsmmc.c
3 *
4 * Driver for OMAP2430/3430 MMC controller.
5 *
6 * Copyright (C) 2007 Texas Instruments.
7 *
8 * Authors:
9 * Syed Mohammed Khasim <x0khasim@ti.com>
10 * Madhusudhan <madhu.cr@ti.com>
11 * Mohit Jalori <mjalori@ti.com>
12 *
13 * This file is licensed under the terms of the GNU General Public License
14 * version 2. This program is licensed "as is" without any warranty of any
15 * kind, whether express or implied.
16 */
17
18 #include <linux/module.h>
19 #include <linux/init.h>
20 #include <linux/kernel.h>
21 #include <linux/debugfs.h>
22 #include <linux/dmaengine.h>
23 #include <linux/seq_file.h>
24 #include <linux/sizes.h>
25 #include <linux/interrupt.h>
26 #include <linux/delay.h>
27 #include <linux/dma-mapping.h>
28 #include <linux/platform_device.h>
29 #include <linux/timer.h>
30 #include <linux/clk.h>
31 #include <linux/of.h>
32 #include <linux/of_irq.h>
33 #include <linux/of_gpio.h>
34 #include <linux/of_device.h>
35 #include <linux/mmc/host.h>
36 #include <linux/mmc/core.h>
37 #include <linux/mmc/mmc.h>
38 #include <linux/mmc/slot-gpio.h>
39 #include <linux/io.h>
40 #include <linux/irq.h>
41 #include <linux/gpio.h>
42 #include <linux/regulator/consumer.h>
43 #include <linux/pinctrl/consumer.h>
44 #include <linux/pm_runtime.h>
45 #include <linux/pm_wakeirq.h>
46 #include <linux/platform_data/hsmmc-omap.h>
47
48 /* OMAP HSMMC Host Controller Registers */
49 #define OMAP_HSMMC_SYSSTATUS 0x0014
50 #define OMAP_HSMMC_CON 0x002C
51 #define OMAP_HSMMC_SDMASA 0x0100
52 #define OMAP_HSMMC_BLK 0x0104
53 #define OMAP_HSMMC_ARG 0x0108
54 #define OMAP_HSMMC_CMD 0x010C
55 #define OMAP_HSMMC_RSP10 0x0110
56 #define OMAP_HSMMC_RSP32 0x0114
57 #define OMAP_HSMMC_RSP54 0x0118
58 #define OMAP_HSMMC_RSP76 0x011C
59 #define OMAP_HSMMC_DATA 0x0120
60 #define OMAP_HSMMC_PSTATE 0x0124
61 #define OMAP_HSMMC_HCTL 0x0128
62 #define OMAP_HSMMC_SYSCTL 0x012C
63 #define OMAP_HSMMC_STAT 0x0130
64 #define OMAP_HSMMC_IE 0x0134
65 #define OMAP_HSMMC_ISE 0x0138
66 #define OMAP_HSMMC_AC12 0x013C
67 #define OMAP_HSMMC_CAPA 0x0140
68
69 #define VS18 (1 << 26)
70 #define VS30 (1 << 25)
71 #define HSS (1 << 21)
72 #define SDVS18 (0x5 << 9)
73 #define SDVS30 (0x6 << 9)
74 #define SDVS33 (0x7 << 9)
75 #define SDVS_MASK 0x00000E00
76 #define SDVSCLR 0xFFFFF1FF
77 #define SDVSDET 0x00000400
78 #define AUTOIDLE 0x1
79 #define SDBP (1 << 8)
80 #define DTO 0xe
81 #define ICE 0x1
82 #define ICS 0x2
83 #define CEN (1 << 2)
84 #define CLKD_MAX 0x3FF /* max clock divisor: 1023 */
85 #define CLKD_MASK 0x0000FFC0
86 #define CLKD_SHIFT 6
87 #define DTO_MASK 0x000F0000
88 #define DTO_SHIFT 16
89 #define INIT_STREAM (1 << 1)
90 #define ACEN_ACMD23 (2 << 2)
91 #define DP_SELECT (1 << 21)
92 #define DDIR (1 << 4)
93 #define DMAE 0x1
94 #define MSBS (1 << 5)
95 #define BCE (1 << 1)
96 #define FOUR_BIT (1 << 1)
97 #define HSPE (1 << 2)
98 #define IWE (1 << 24)
99 #define DDR (1 << 19)
100 #define CLKEXTFREE (1 << 16)
101 #define CTPL (1 << 11)
102 #define DW8 (1 << 5)
103 #define OD 0x1
104 #define STAT_CLEAR 0xFFFFFFFF
105 #define INIT_STREAM_CMD 0x00000000
106 #define DUAL_VOLT_OCR_BIT 7
107 #define SRC (1 << 25)
108 #define SRD (1 << 26)
109 #define SOFTRESET (1 << 1)
110
111 /* PSTATE */
112 #define DLEV_DAT(x) (1 << (20 + (x)))
113
114 /* Interrupt masks for IE and ISE register */
115 #define CC_EN (1 << 0)
116 #define TC_EN (1 << 1)
117 #define BWR_EN (1 << 4)
118 #define BRR_EN (1 << 5)
119 #define CIRQ_EN (1 << 8)
120 #define ERR_EN (1 << 15)
121 #define CTO_EN (1 << 16)
122 #define CCRC_EN (1 << 17)
123 #define CEB_EN (1 << 18)
124 #define CIE_EN (1 << 19)
125 #define DTO_EN (1 << 20)
126 #define DCRC_EN (1 << 21)
127 #define DEB_EN (1 << 22)
128 #define ACE_EN (1 << 24)
129 #define CERR_EN (1 << 28)
130 #define BADA_EN (1 << 29)
131
132 #define INT_EN_MASK (BADA_EN | CERR_EN | ACE_EN | DEB_EN | DCRC_EN |\
133 DTO_EN | CIE_EN | CEB_EN | CCRC_EN | CTO_EN | \
134 BRR_EN | BWR_EN | TC_EN | CC_EN)
135
136 #define CNI (1 << 7)
137 #define ACIE (1 << 4)
138 #define ACEB (1 << 3)
139 #define ACCE (1 << 2)
140 #define ACTO (1 << 1)
141 #define ACNE (1 << 0)
142
143 #define MMC_AUTOSUSPEND_DELAY 100
144 #define MMC_TIMEOUT_MS 20 /* 20 mSec */
145 #define MMC_TIMEOUT_US 20000 /* 20000 micro Sec */
146 #define OMAP_MMC_MIN_CLOCK 400000
147 #define OMAP_MMC_MAX_CLOCK 52000000
148 #define DRIVER_NAME "omap_hsmmc"
149
150 /*
151 * One controller can have multiple slots, like on some omap boards using
152 * omap.c controller driver. Luckily this is not currently done on any known
153 * omap_hsmmc.c device.
154 */
155 #define mmc_pdata(host) host->pdata
156
157 /*
158 * MMC Host controller read/write API's
159 */
160 #define OMAP_HSMMC_READ(base, reg) \
161 __raw_readl((base) + OMAP_HSMMC_##reg)
162
163 #define OMAP_HSMMC_WRITE(base, reg, val) \
164 __raw_writel((val), (base) + OMAP_HSMMC_##reg)
165
166 struct omap_hsmmc_next {
167 unsigned int dma_len;
168 s32 cookie;
169 };
170
171 struct omap_hsmmc_host {
172 struct device *dev;
173 struct mmc_host *mmc;
174 struct mmc_request *mrq;
175 struct mmc_command *cmd;
176 struct mmc_data *data;
177 struct clk *fclk;
178 struct clk *dbclk;
179 struct regulator *pbias;
180 bool pbias_enabled;
181 void __iomem *base;
182 int vqmmc_enabled;
183 resource_size_t mapbase;
184 spinlock_t irq_lock; /* Prevent races with irq handler */
185 unsigned int dma_len;
186 unsigned int dma_sg_idx;
187 unsigned char bus_mode;
188 unsigned char power_mode;
189 int suspended;
190 u32 con;
191 u32 hctl;
192 u32 sysctl;
193 u32 capa;
194 int irq;
195 int wake_irq;
196 int use_dma, dma_ch;
197 struct dma_chan *tx_chan;
198 struct dma_chan *rx_chan;
199 int response_busy;
200 int context_loss;
201 int protect_card;
202 int reqs_blocked;
203 int req_in_progress;
204 unsigned long clk_rate;
205 unsigned int flags;
206 #define AUTO_CMD23 (1 << 0) /* Auto CMD23 support */
207 #define HSMMC_SDIO_IRQ_ENABLED (1 << 1) /* SDIO irq enabled */
208 struct omap_hsmmc_next next_data;
209 struct omap_hsmmc_platform_data *pdata;
210
211 /* return MMC cover switch state, can be NULL if not supported.
212 *
213 * possible return values:
214 * 0 - closed
215 * 1 - open
216 */
217 int (*get_cover_state)(struct device *dev);
218
219 int (*card_detect)(struct device *dev);
220 };
221
222 struct omap_mmc_of_data {
223 u32 reg_offset;
224 u8 controller_flags;
225 };
226
227 static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host);
228
229 static int omap_hsmmc_card_detect(struct device *dev)
230 {
231 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
232
233 return mmc_gpio_get_cd(host->mmc);
234 }
235
236 static int omap_hsmmc_get_cover_state(struct device *dev)
237 {
238 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
239
240 return mmc_gpio_get_cd(host->mmc);
241 }
242
243 static int omap_hsmmc_enable_supply(struct mmc_host *mmc)
244 {
245 int ret;
246 struct omap_hsmmc_host *host = mmc_priv(mmc);
247 struct mmc_ios *ios = &mmc->ios;
248
249 if (!IS_ERR(mmc->supply.vmmc)) {
250 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
251 if (ret)
252 return ret;
253 }
254
255 /* Enable interface voltage rail, if needed */
256 if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) {
257 ret = regulator_enable(mmc->supply.vqmmc);
258 if (ret) {
259 dev_err(mmc_dev(mmc), "vmmc_aux reg enable failed\n");
260 goto err_vqmmc;
261 }
262 host->vqmmc_enabled = 1;
263 }
264
265 return 0;
266
267 err_vqmmc:
268 if (!IS_ERR(mmc->supply.vmmc))
269 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
270
271 return ret;
272 }
273
274 static int omap_hsmmc_disable_supply(struct mmc_host *mmc)
275 {
276 int ret;
277 int status;
278 struct omap_hsmmc_host *host = mmc_priv(mmc);
279
280 if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) {
281 ret = regulator_disable(mmc->supply.vqmmc);
282 if (ret) {
283 dev_err(mmc_dev(mmc), "vmmc_aux reg disable failed\n");
284 return ret;
285 }
286 host->vqmmc_enabled = 0;
287 }
288
289 if (!IS_ERR(mmc->supply.vmmc)) {
290 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
291 if (ret)
292 goto err_set_ocr;
293 }
294
295 return 0;
296
297 err_set_ocr:
298 if (!IS_ERR(mmc->supply.vqmmc)) {
299 status = regulator_enable(mmc->supply.vqmmc);
300 if (status)
301 dev_err(mmc_dev(mmc), "vmmc_aux re-enable failed\n");
302 }
303
304 return ret;
305 }
306
307 static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on)
308 {
309 int ret;
310
311 if (IS_ERR(host->pbias))
312 return 0;
313
314 if (power_on) {
315 if (host->pbias_enabled == 0) {
316 ret = regulator_enable(host->pbias);
317 if (ret) {
318 dev_err(host->dev, "pbias reg enable fail\n");
319 return ret;
320 }
321 host->pbias_enabled = 1;
322 }
323 } else {
324 if (host->pbias_enabled == 1) {
325 ret = regulator_disable(host->pbias);
326 if (ret) {
327 dev_err(host->dev, "pbias reg disable fail\n");
328 return ret;
329 }
330 host->pbias_enabled = 0;
331 }
332 }
333
334 return 0;
335 }
336
337 static int omap_hsmmc_set_power(struct omap_hsmmc_host *host, int power_on)
338 {
339 struct mmc_host *mmc = host->mmc;
340 int ret = 0;
341
342 /*
343 * If we don't see a Vcc regulator, assume it's a fixed
344 * voltage always-on regulator.
345 */
346 if (IS_ERR(mmc->supply.vmmc))
347 return 0;
348
349 ret = omap_hsmmc_set_pbias(host, false);
350 if (ret)
351 return ret;
352
353 /*
354 * Assume Vcc regulator is used only to power the card ... OMAP
355 * VDDS is used to power the pins, optionally with a transceiver to
356 * support cards using voltages other than VDDS (1.8V nominal). When a
357 * transceiver is used, DAT3..7 are muxed as transceiver control pins.
358 *
359 * In some cases this regulator won't support enable/disable;
360 * e.g. it's a fixed rail for a WLAN chip.
361 *
362 * In other cases vcc_aux switches interface power. Example, for
363 * eMMC cards it represents VccQ. Sometimes transceivers or SDIO
364 * chips/cards need an interface voltage rail too.
365 */
366 if (power_on) {
367 ret = omap_hsmmc_enable_supply(mmc);
368 if (ret)
369 return ret;
370
371 ret = omap_hsmmc_set_pbias(host, true);
372 if (ret)
373 goto err_set_voltage;
374 } else {
375 ret = omap_hsmmc_disable_supply(mmc);
376 if (ret)
377 return ret;
378 }
379
380 return 0;
381
382 err_set_voltage:
383 omap_hsmmc_disable_supply(mmc);
384
385 return ret;
386 }
387
388 static int omap_hsmmc_disable_boot_regulator(struct regulator *reg)
389 {
390 int ret;
391
392 if (IS_ERR(reg))
393 return 0;
394
395 if (regulator_is_enabled(reg)) {
396 ret = regulator_enable(reg);
397 if (ret)
398 return ret;
399
400 ret = regulator_disable(reg);
401 if (ret)
402 return ret;
403 }
404
405 return 0;
406 }
407
408 static int omap_hsmmc_disable_boot_regulators(struct omap_hsmmc_host *host)
409 {
410 struct mmc_host *mmc = host->mmc;
411 int ret;
412
413 /*
414 * disable regulators enabled during boot and get the usecount
415 * right so that regulators can be enabled/disabled by checking
416 * the return value of regulator_is_enabled
417 */
418 ret = omap_hsmmc_disable_boot_regulator(mmc->supply.vmmc);
419 if (ret) {
420 dev_err(host->dev, "fail to disable boot enabled vmmc reg\n");
421 return ret;
422 }
423
424 ret = omap_hsmmc_disable_boot_regulator(mmc->supply.vqmmc);
425 if (ret) {
426 dev_err(host->dev,
427 "fail to disable boot enabled vmmc_aux reg\n");
428 return ret;
429 }
430
431 ret = omap_hsmmc_disable_boot_regulator(host->pbias);
432 if (ret) {
433 dev_err(host->dev,
434 "failed to disable boot enabled pbias reg\n");
435 return ret;
436 }
437
438 return 0;
439 }
440
441 static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
442 {
443 int ret;
444 struct mmc_host *mmc = host->mmc;
445
446
447 ret = mmc_regulator_get_supply(mmc);
448 if (ret)
449 return ret;
450
451 /* Allow an aux regulator */
452 if (IS_ERR(mmc->supply.vqmmc)) {
453 mmc->supply.vqmmc = devm_regulator_get_optional(host->dev,
454 "vmmc_aux");
455 if (IS_ERR(mmc->supply.vqmmc)) {
456 ret = PTR_ERR(mmc->supply.vqmmc);
457 if ((ret != -ENODEV) && host->dev->of_node)
458 return ret;
459 dev_dbg(host->dev, "unable to get vmmc_aux regulator %ld\n",
460 PTR_ERR(mmc->supply.vqmmc));
461 }
462 }
463
464 host->pbias = devm_regulator_get_optional(host->dev, "pbias");
465 if (IS_ERR(host->pbias)) {
466 ret = PTR_ERR(host->pbias);
467 if ((ret != -ENODEV) && host->dev->of_node) {
468 dev_err(host->dev,
469 "SD card detect fail? enable CONFIG_REGULATOR_PBIAS\n");
470 return ret;
471 }
472 dev_dbg(host->dev, "unable to get pbias regulator %ld\n",
473 PTR_ERR(host->pbias));
474 }
475
476 /* For eMMC do not power off when not in sleep state */
477 if (mmc_pdata(host)->no_regulator_off_init)
478 return 0;
479
480 ret = omap_hsmmc_disable_boot_regulators(host);
481 if (ret)
482 return ret;
483
484 return 0;
485 }
486
487 static irqreturn_t omap_hsmmc_cover_irq(int irq, void *dev_id);
488
489 static int omap_hsmmc_gpio_init(struct mmc_host *mmc,
490 struct omap_hsmmc_host *host,
491 struct omap_hsmmc_platform_data *pdata)
492 {
493 int ret;
494
495 if (gpio_is_valid(pdata->gpio_cod)) {
496 ret = mmc_gpio_request_cd(mmc, pdata->gpio_cod, 0);
497 if (ret)
498 return ret;
499
500 host->get_cover_state = omap_hsmmc_get_cover_state;
501 mmc_gpio_set_cd_isr(mmc, omap_hsmmc_cover_irq);
502 } else if (gpio_is_valid(pdata->gpio_cd)) {
503 ret = mmc_gpio_request_cd(mmc, pdata->gpio_cd, 0);
504 if (ret)
505 return ret;
506
507 host->card_detect = omap_hsmmc_card_detect;
508 }
509
510 if (gpio_is_valid(pdata->gpio_wp)) {
511 ret = mmc_gpio_request_ro(mmc, pdata->gpio_wp);
512 if (ret)
513 return ret;
514 }
515
516 return 0;
517 }
518
519 /*
520 * Start clock to the card
521 */
522 static void omap_hsmmc_start_clock(struct omap_hsmmc_host *host)
523 {
524 OMAP_HSMMC_WRITE(host->base, SYSCTL,
525 OMAP_HSMMC_READ(host->base, SYSCTL) | CEN);
526 }
527
528 /*
529 * Stop clock to the card
530 */
531 static void omap_hsmmc_stop_clock(struct omap_hsmmc_host *host)
532 {
533 OMAP_HSMMC_WRITE(host->base, SYSCTL,
534 OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN);
535 if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0)
536 dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stopped\n");
537 }
538
539 static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host,
540 struct mmc_command *cmd)
541 {
542 u32 irq_mask = INT_EN_MASK;
543 unsigned long flags;
544
545 if (host->use_dma)
546 irq_mask &= ~(BRR_EN | BWR_EN);
547
548 /* Disable timeout for erases */
549 if (cmd->opcode == MMC_ERASE)
550 irq_mask &= ~DTO_EN;
551
552 spin_lock_irqsave(&host->irq_lock, flags);
553 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
554 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
555
556 /* latch pending CIRQ, but don't signal MMC core */
557 if (host->flags & HSMMC_SDIO_IRQ_ENABLED)
558 irq_mask |= CIRQ_EN;
559 OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
560 spin_unlock_irqrestore(&host->irq_lock, flags);
561 }
562
563 static void omap_hsmmc_disable_irq(struct omap_hsmmc_host *host)
564 {
565 u32 irq_mask = 0;
566 unsigned long flags;
567
568 spin_lock_irqsave(&host->irq_lock, flags);
569 /* no transfer running but need to keep cirq if enabled */
570 if (host->flags & HSMMC_SDIO_IRQ_ENABLED)
571 irq_mask |= CIRQ_EN;
572 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
573 OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
574 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
575 spin_unlock_irqrestore(&host->irq_lock, flags);
576 }
577
578 /* Calculate divisor for the given clock frequency */
579 static u16 calc_divisor(struct omap_hsmmc_host *host, struct mmc_ios *ios)
580 {
581 u16 dsor = 0;
582
583 if (ios->clock) {
584 dsor = DIV_ROUND_UP(clk_get_rate(host->fclk), ios->clock);
585 if (dsor > CLKD_MAX)
586 dsor = CLKD_MAX;
587 }
588
589 return dsor;
590 }
591
592 static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host)
593 {
594 struct mmc_ios *ios = &host->mmc->ios;
595 unsigned long regval;
596 unsigned long timeout;
597 unsigned long clkdiv;
598
599 dev_vdbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock);
600
601 omap_hsmmc_stop_clock(host);
602
603 regval = OMAP_HSMMC_READ(host->base, SYSCTL);
604 regval = regval & ~(CLKD_MASK | DTO_MASK);
605 clkdiv = calc_divisor(host, ios);
606 regval = regval | (clkdiv << 6) | (DTO << 16);
607 OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
608 OMAP_HSMMC_WRITE(host->base, SYSCTL,
609 OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
610
611 /* Wait till the ICS bit is set */
612 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
613 while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
614 && time_before(jiffies, timeout))
615 cpu_relax();
616
617 /*
618 * Enable High-Speed Support
619 * Pre-Requisites
620 * - Controller should support High-Speed-Enable Bit
621 * - Controller should not be using DDR Mode
622 * - Controller should advertise that it supports High Speed
623 * in capabilities register
624 * - MMC/SD clock coming out of controller > 25MHz
625 */
626 if ((mmc_pdata(host)->features & HSMMC_HAS_HSPE_SUPPORT) &&
627 (ios->timing != MMC_TIMING_MMC_DDR52) &&
628 (ios->timing != MMC_TIMING_UHS_DDR50) &&
629 ((OMAP_HSMMC_READ(host->base, CAPA) & HSS) == HSS)) {
630 regval = OMAP_HSMMC_READ(host->base, HCTL);
631 if (clkdiv && (clk_get_rate(host->fclk)/clkdiv) > 25000000)
632 regval |= HSPE;
633 else
634 regval &= ~HSPE;
635
636 OMAP_HSMMC_WRITE(host->base, HCTL, regval);
637 }
638
639 omap_hsmmc_start_clock(host);
640 }
641
642 static void omap_hsmmc_set_bus_width(struct omap_hsmmc_host *host)
643 {
644 struct mmc_ios *ios = &host->mmc->ios;
645 u32 con;
646
647 con = OMAP_HSMMC_READ(host->base, CON);
648 if (ios->timing == MMC_TIMING_MMC_DDR52 ||
649 ios->timing == MMC_TIMING_UHS_DDR50)
650 con |= DDR; /* configure in DDR mode */
651 else
652 con &= ~DDR;
653 switch (ios->bus_width) {
654 case MMC_BUS_WIDTH_8:
655 OMAP_HSMMC_WRITE(host->base, CON, con | DW8);
656 break;
657 case MMC_BUS_WIDTH_4:
658 OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
659 OMAP_HSMMC_WRITE(host->base, HCTL,
660 OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
661 break;
662 case MMC_BUS_WIDTH_1:
663 OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
664 OMAP_HSMMC_WRITE(host->base, HCTL,
665 OMAP_HSMMC_READ(host->base, HCTL) & ~FOUR_BIT);
666 break;
667 }
668 }
669
670 static void omap_hsmmc_set_bus_mode(struct omap_hsmmc_host *host)
671 {
672 struct mmc_ios *ios = &host->mmc->ios;
673 u32 con;
674
675 con = OMAP_HSMMC_READ(host->base, CON);
676 if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
677 OMAP_HSMMC_WRITE(host->base, CON, con | OD);
678 else
679 OMAP_HSMMC_WRITE(host->base, CON, con & ~OD);
680 }
681
682 #ifdef CONFIG_PM
683
684 /*
685 * Restore the MMC host context, if it was lost as result of a
686 * power state change.
687 */
688 static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
689 {
690 struct mmc_ios *ios = &host->mmc->ios;
691 u32 hctl, capa;
692 unsigned long timeout;
693
694 if (host->con == OMAP_HSMMC_READ(host->base, CON) &&
695 host->hctl == OMAP_HSMMC_READ(host->base, HCTL) &&
696 host->sysctl == OMAP_HSMMC_READ(host->base, SYSCTL) &&
697 host->capa == OMAP_HSMMC_READ(host->base, CAPA))
698 return 0;
699
700 host->context_loss++;
701
702 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
703 if (host->power_mode != MMC_POWER_OFF &&
704 (1 << ios->vdd) <= MMC_VDD_23_24)
705 hctl = SDVS18;
706 else
707 hctl = SDVS30;
708 capa = VS30 | VS18;
709 } else {
710 hctl = SDVS18;
711 capa = VS18;
712 }
713
714 if (host->mmc->caps & MMC_CAP_SDIO_IRQ)
715 hctl |= IWE;
716
717 OMAP_HSMMC_WRITE(host->base, HCTL,
718 OMAP_HSMMC_READ(host->base, HCTL) | hctl);
719
720 OMAP_HSMMC_WRITE(host->base, CAPA,
721 OMAP_HSMMC_READ(host->base, CAPA) | capa);
722
723 OMAP_HSMMC_WRITE(host->base, HCTL,
724 OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
725
726 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
727 while ((OMAP_HSMMC_READ(host->base, HCTL) & SDBP) != SDBP
728 && time_before(jiffies, timeout))
729 ;
730
731 OMAP_HSMMC_WRITE(host->base, ISE, 0);
732 OMAP_HSMMC_WRITE(host->base, IE, 0);
733 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
734
735 /* Do not initialize card-specific things if the power is off */
736 if (host->power_mode == MMC_POWER_OFF)
737 goto out;
738
739 omap_hsmmc_set_bus_width(host);
740
741 omap_hsmmc_set_clock(host);
742
743 omap_hsmmc_set_bus_mode(host);
744
745 out:
746 dev_dbg(mmc_dev(host->mmc), "context is restored: restore count %d\n",
747 host->context_loss);
748 return 0;
749 }
750
751 /*
752 * Save the MMC host context (store the number of power state changes so far).
753 */
754 static void omap_hsmmc_context_save(struct omap_hsmmc_host *host)
755 {
756 host->con = OMAP_HSMMC_READ(host->base, CON);
757 host->hctl = OMAP_HSMMC_READ(host->base, HCTL);
758 host->sysctl = OMAP_HSMMC_READ(host->base, SYSCTL);
759 host->capa = OMAP_HSMMC_READ(host->base, CAPA);
760 }
761
762 #else
763
764 static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
765 {
766 return 0;
767 }
768
769 static void omap_hsmmc_context_save(struct omap_hsmmc_host *host)
770 {
771 }
772
773 #endif
774
775 /*
776 * Send init stream sequence to card
777 * before sending IDLE command
778 */
779 static void send_init_stream(struct omap_hsmmc_host *host)
780 {
781 int reg = 0;
782 unsigned long timeout;
783
784 if (host->protect_card)
785 return;
786
787 disable_irq(host->irq);
788
789 OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
790 OMAP_HSMMC_WRITE(host->base, CON,
791 OMAP_HSMMC_READ(host->base, CON) | INIT_STREAM);
792 OMAP_HSMMC_WRITE(host->base, CMD, INIT_STREAM_CMD);
793
794 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
795 while ((reg != CC_EN) && time_before(jiffies, timeout))
796 reg = OMAP_HSMMC_READ(host->base, STAT) & CC_EN;
797
798 OMAP_HSMMC_WRITE(host->base, CON,
799 OMAP_HSMMC_READ(host->base, CON) & ~INIT_STREAM);
800
801 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
802 OMAP_HSMMC_READ(host->base, STAT);
803
804 enable_irq(host->irq);
805 }
806
807 static inline
808 int omap_hsmmc_cover_is_closed(struct omap_hsmmc_host *host)
809 {
810 int r = 1;
811
812 if (host->get_cover_state)
813 r = host->get_cover_state(host->dev);
814 return r;
815 }
816
817 static ssize_t
818 omap_hsmmc_show_cover_switch(struct device *dev, struct device_attribute *attr,
819 char *buf)
820 {
821 struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
822 struct omap_hsmmc_host *host = mmc_priv(mmc);
823
824 return sprintf(buf, "%s\n",
825 omap_hsmmc_cover_is_closed(host) ? "closed" : "open");
826 }
827
828 static DEVICE_ATTR(cover_switch, S_IRUGO, omap_hsmmc_show_cover_switch, NULL);
829
830 static ssize_t
831 omap_hsmmc_show_slot_name(struct device *dev, struct device_attribute *attr,
832 char *buf)
833 {
834 struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
835 struct omap_hsmmc_host *host = mmc_priv(mmc);
836
837 return sprintf(buf, "%s\n", mmc_pdata(host)->name);
838 }
839
840 static DEVICE_ATTR(slot_name, S_IRUGO, omap_hsmmc_show_slot_name, NULL);
841
842 /*
843 * Configure the response type and send the cmd.
844 */
845 static void
846 omap_hsmmc_start_command(struct omap_hsmmc_host *host, struct mmc_command *cmd,
847 struct mmc_data *data)
848 {
849 int cmdreg = 0, resptype = 0, cmdtype = 0;
850
851 dev_vdbg(mmc_dev(host->mmc), "%s: CMD%d, argument 0x%08x\n",
852 mmc_hostname(host->mmc), cmd->opcode, cmd->arg);
853 host->cmd = cmd;
854
855 omap_hsmmc_enable_irq(host, cmd);
856
857 host->response_busy = 0;
858 if (cmd->flags & MMC_RSP_PRESENT) {
859 if (cmd->flags & MMC_RSP_136)
860 resptype = 1;
861 else if (cmd->flags & MMC_RSP_BUSY) {
862 resptype = 3;
863 host->response_busy = 1;
864 } else
865 resptype = 2;
866 }
867
868 /*
869 * Unlike OMAP1 controller, the cmdtype does not seem to be based on
870 * ac, bc, adtc, bcr. Only commands ending an open ended transfer need
871 * a val of 0x3, rest 0x0.
872 */
873 if (cmd == host->mrq->stop)
874 cmdtype = 0x3;
875
876 cmdreg = (cmd->opcode << 24) | (resptype << 16) | (cmdtype << 22);
877
878 if ((host->flags & AUTO_CMD23) && mmc_op_multi(cmd->opcode) &&
879 host->mrq->sbc) {
880 cmdreg |= ACEN_ACMD23;
881 OMAP_HSMMC_WRITE(host->base, SDMASA, host->mrq->sbc->arg);
882 }
883 if (data) {
884 cmdreg |= DP_SELECT | MSBS | BCE;
885 if (data->flags & MMC_DATA_READ)
886 cmdreg |= DDIR;
887 else
888 cmdreg &= ~(DDIR);
889 }
890
891 if (host->use_dma)
892 cmdreg |= DMAE;
893
894 host->req_in_progress = 1;
895
896 OMAP_HSMMC_WRITE(host->base, ARG, cmd->arg);
897 OMAP_HSMMC_WRITE(host->base, CMD, cmdreg);
898 }
899
900 static struct dma_chan *omap_hsmmc_get_dma_chan(struct omap_hsmmc_host *host,
901 struct mmc_data *data)
902 {
903 return data->flags & MMC_DATA_WRITE ? host->tx_chan : host->rx_chan;
904 }
905
906 static void omap_hsmmc_request_done(struct omap_hsmmc_host *host, struct mmc_request *mrq)
907 {
908 int dma_ch;
909 unsigned long flags;
910
911 spin_lock_irqsave(&host->irq_lock, flags);
912 host->req_in_progress = 0;
913 dma_ch = host->dma_ch;
914 spin_unlock_irqrestore(&host->irq_lock, flags);
915
916 omap_hsmmc_disable_irq(host);
917 /* Do not complete the request if DMA is still in progress */
918 if (mrq->data && host->use_dma && dma_ch != -1)
919 return;
920 host->mrq = NULL;
921 mmc_request_done(host->mmc, mrq);
922 }
923
924 /*
925 * Notify the transfer complete to MMC core
926 */
927 static void
928 omap_hsmmc_xfer_done(struct omap_hsmmc_host *host, struct mmc_data *data)
929 {
930 if (!data) {
931 struct mmc_request *mrq = host->mrq;
932
933 /* TC before CC from CMD6 - don't know why, but it happens */
934 if (host->cmd && host->cmd->opcode == 6 &&
935 host->response_busy) {
936 host->response_busy = 0;
937 return;
938 }
939
940 omap_hsmmc_request_done(host, mrq);
941 return;
942 }
943
944 host->data = NULL;
945
946 if (!data->error)
947 data->bytes_xfered += data->blocks * (data->blksz);
948 else
949 data->bytes_xfered = 0;
950
951 if (data->stop && (data->error || !host->mrq->sbc))
952 omap_hsmmc_start_command(host, data->stop, NULL);
953 else
954 omap_hsmmc_request_done(host, data->mrq);
955 }
956
957 /*
958 * Notify the core about command completion
959 */
960 static void
961 omap_hsmmc_cmd_done(struct omap_hsmmc_host *host, struct mmc_command *cmd)
962 {
963 if (host->mrq->sbc && (host->cmd == host->mrq->sbc) &&
964 !host->mrq->sbc->error && !(host->flags & AUTO_CMD23)) {
965 host->cmd = NULL;
966 omap_hsmmc_start_dma_transfer(host);
967 omap_hsmmc_start_command(host, host->mrq->cmd,
968 host->mrq->data);
969 return;
970 }
971
972 host->cmd = NULL;
973
974 if (cmd->flags & MMC_RSP_PRESENT) {
975 if (cmd->flags & MMC_RSP_136) {
976 /* response type 2 */
977 cmd->resp[3] = OMAP_HSMMC_READ(host->base, RSP10);
978 cmd->resp[2] = OMAP_HSMMC_READ(host->base, RSP32);
979 cmd->resp[1] = OMAP_HSMMC_READ(host->base, RSP54);
980 cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP76);
981 } else {
982 /* response types 1, 1b, 3, 4, 5, 6 */
983 cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP10);
984 }
985 }
986 if ((host->data == NULL && !host->response_busy) || cmd->error)
987 omap_hsmmc_request_done(host, host->mrq);
988 }
989
990 /*
991 * DMA clean up for command errors
992 */
993 static void omap_hsmmc_dma_cleanup(struct omap_hsmmc_host *host, int errno)
994 {
995 int dma_ch;
996 unsigned long flags;
997
998 host->data->error = errno;
999
1000 spin_lock_irqsave(&host->irq_lock, flags);
1001 dma_ch = host->dma_ch;
1002 host->dma_ch = -1;
1003 spin_unlock_irqrestore(&host->irq_lock, flags);
1004
1005 if (host->use_dma && dma_ch != -1) {
1006 struct dma_chan *chan = omap_hsmmc_get_dma_chan(host, host->data);
1007
1008 dmaengine_terminate_all(chan);
1009 dma_unmap_sg(chan->device->dev,
1010 host->data->sg, host->data->sg_len,
1011 mmc_get_dma_dir(host->data));
1012
1013 host->data->host_cookie = 0;
1014 }
1015 host->data = NULL;
1016 }
1017
1018 /*
1019 * Readable error output
1020 */
1021 #ifdef CONFIG_MMC_DEBUG
1022 static void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host, u32 status)
1023 {
1024 /* --- means reserved bit without definition at documentation */
1025 static const char *omap_hsmmc_status_bits[] = {
1026 "CC" , "TC" , "BGE", "---", "BWR" , "BRR" , "---" , "---" ,
1027 "CIRQ", "OBI" , "---", "---", "---" , "---" , "---" , "ERRI",
1028 "CTO" , "CCRC", "CEB", "CIE", "DTO" , "DCRC", "DEB" , "---" ,
1029 "ACE" , "---" , "---", "---", "CERR", "BADA", "---" , "---"
1030 };
1031 char res[256];
1032 char *buf = res;
1033 int len, i;
1034
1035 len = sprintf(buf, "MMC IRQ 0x%x :", status);
1036 buf += len;
1037
1038 for (i = 0; i < ARRAY_SIZE(omap_hsmmc_status_bits); i++)
1039 if (status & (1 << i)) {
1040 len = sprintf(buf, " %s", omap_hsmmc_status_bits[i]);
1041 buf += len;
1042 }
1043
1044 dev_vdbg(mmc_dev(host->mmc), "%s\n", res);
1045 }
1046 #else
1047 static inline void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host,
1048 u32 status)
1049 {
1050 }
1051 #endif /* CONFIG_MMC_DEBUG */
1052
1053 /*
1054 * MMC controller internal state machines reset
1055 *
1056 * Used to reset command or data internal state machines, using respectively
1057 * SRC or SRD bit of SYSCTL register
1058 * Can be called from interrupt context
1059 */
1060 static inline void omap_hsmmc_reset_controller_fsm(struct omap_hsmmc_host *host,
1061 unsigned long bit)
1062 {
1063 unsigned long i = 0;
1064 unsigned long limit = MMC_TIMEOUT_US;
1065
1066 OMAP_HSMMC_WRITE(host->base, SYSCTL,
1067 OMAP_HSMMC_READ(host->base, SYSCTL) | bit);
1068
1069 /*
1070 * OMAP4 ES2 and greater has an updated reset logic.
1071 * Monitor a 0->1 transition first
1072 */
1073 if (mmc_pdata(host)->features & HSMMC_HAS_UPDATED_RESET) {
1074 while ((!(OMAP_HSMMC_READ(host->base, SYSCTL) & bit))
1075 && (i++ < limit))
1076 udelay(1);
1077 }
1078 i = 0;
1079
1080 while ((OMAP_HSMMC_READ(host->base, SYSCTL) & bit) &&
1081 (i++ < limit))
1082 udelay(1);
1083
1084 if (OMAP_HSMMC_READ(host->base, SYSCTL) & bit)
1085 dev_err(mmc_dev(host->mmc),
1086 "Timeout waiting on controller reset in %s\n",
1087 __func__);
1088 }
1089
1090 static void hsmmc_command_incomplete(struct omap_hsmmc_host *host,
1091 int err, int end_cmd)
1092 {
1093 if (end_cmd) {
1094 omap_hsmmc_reset_controller_fsm(host, SRC);
1095 if (host->cmd)
1096 host->cmd->error = err;
1097 }
1098
1099 if (host->data) {
1100 omap_hsmmc_reset_controller_fsm(host, SRD);
1101 omap_hsmmc_dma_cleanup(host, err);
1102 } else if (host->mrq && host->mrq->cmd)
1103 host->mrq->cmd->error = err;
1104 }
1105
1106 static void omap_hsmmc_do_irq(struct omap_hsmmc_host *host, int status)
1107 {
1108 struct mmc_data *data;
1109 int end_cmd = 0, end_trans = 0;
1110 int error = 0;
1111
1112 data = host->data;
1113 dev_vdbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
1114
1115 if (status & ERR_EN) {
1116 omap_hsmmc_dbg_report_irq(host, status);
1117
1118 if (status & (CTO_EN | CCRC_EN | CEB_EN))
1119 end_cmd = 1;
1120 if (host->data || host->response_busy) {
1121 end_trans = !end_cmd;
1122 host->response_busy = 0;
1123 }
1124 if (status & (CTO_EN | DTO_EN))
1125 hsmmc_command_incomplete(host, -ETIMEDOUT, end_cmd);
1126 else if (status & (CCRC_EN | DCRC_EN | DEB_EN | CEB_EN |
1127 BADA_EN))
1128 hsmmc_command_incomplete(host, -EILSEQ, end_cmd);
1129
1130 if (status & ACE_EN) {
1131 u32 ac12;
1132 ac12 = OMAP_HSMMC_READ(host->base, AC12);
1133 if (!(ac12 & ACNE) && host->mrq->sbc) {
1134 end_cmd = 1;
1135 if (ac12 & ACTO)
1136 error = -ETIMEDOUT;
1137 else if (ac12 & (ACCE | ACEB | ACIE))
1138 error = -EILSEQ;
1139 host->mrq->sbc->error = error;
1140 hsmmc_command_incomplete(host, error, end_cmd);
1141 }
1142 dev_dbg(mmc_dev(host->mmc), "AC12 err: 0x%x\n", ac12);
1143 }
1144 }
1145
1146 OMAP_HSMMC_WRITE(host->base, STAT, status);
1147 if (end_cmd || ((status & CC_EN) && host->cmd))
1148 omap_hsmmc_cmd_done(host, host->cmd);
1149 if ((end_trans || (status & TC_EN)) && host->mrq)
1150 omap_hsmmc_xfer_done(host, data);
1151 }
1152
1153 /*
1154 * MMC controller IRQ handler
1155 */
1156 static irqreturn_t omap_hsmmc_irq(int irq, void *dev_id)
1157 {
1158 struct omap_hsmmc_host *host = dev_id;
1159 int status;
1160
1161 status = OMAP_HSMMC_READ(host->base, STAT);
1162 while (status & (INT_EN_MASK | CIRQ_EN)) {
1163 if (host->req_in_progress)
1164 omap_hsmmc_do_irq(host, status);
1165
1166 if (status & CIRQ_EN)
1167 mmc_signal_sdio_irq(host->mmc);
1168
1169 /* Flush posted write */
1170 status = OMAP_HSMMC_READ(host->base, STAT);
1171 }
1172
1173 return IRQ_HANDLED;
1174 }
1175
1176 static void set_sd_bus_power(struct omap_hsmmc_host *host)
1177 {
1178 unsigned long i;
1179
1180 OMAP_HSMMC_WRITE(host->base, HCTL,
1181 OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
1182 for (i = 0; i < loops_per_jiffy; i++) {
1183 if (OMAP_HSMMC_READ(host->base, HCTL) & SDBP)
1184 break;
1185 cpu_relax();
1186 }
1187 }
1188
1189 /*
1190 * Switch MMC interface voltage ... only relevant for MMC1.
1191 *
1192 * MMC2 and MMC3 use fixed 1.8V levels, and maybe a transceiver.
1193 * The MMC2 transceiver controls are used instead of DAT4..DAT7.
1194 * Some chips, like eMMC ones, use internal transceivers.
1195 */
1196 static int omap_hsmmc_switch_opcond(struct omap_hsmmc_host *host, int vdd)
1197 {
1198 u32 reg_val = 0;
1199 int ret;
1200
1201 /* Disable the clocks */
1202 if (host->dbclk)
1203 clk_disable_unprepare(host->dbclk);
1204
1205 /* Turn the power off */
1206 ret = omap_hsmmc_set_power(host, 0);
1207
1208 /* Turn the power ON with given VDD 1.8 or 3.0v */
1209 if (!ret)
1210 ret = omap_hsmmc_set_power(host, 1);
1211 if (host->dbclk)
1212 clk_prepare_enable(host->dbclk);
1213
1214 if (ret != 0)
1215 goto err;
1216
1217 OMAP_HSMMC_WRITE(host->base, HCTL,
1218 OMAP_HSMMC_READ(host->base, HCTL) & SDVSCLR);
1219 reg_val = OMAP_HSMMC_READ(host->base, HCTL);
1220
1221 /*
1222 * If a MMC dual voltage card is detected, the set_ios fn calls
1223 * this fn with VDD bit set for 1.8V. Upon card removal from the
1224 * slot, omap_hsmmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF.
1225 *
1226 * Cope with a bit of slop in the range ... per data sheets:
1227 * - "1.8V" for vdds_mmc1/vdds_mmc1a can be up to 2.45V max,
1228 * but recommended values are 1.71V to 1.89V
1229 * - "3.0V" for vdds_mmc1/vdds_mmc1a can be up to 3.5V max,
1230 * but recommended values are 2.7V to 3.3V
1231 *
1232 * Board setup code shouldn't permit anything very out-of-range.
1233 * TWL4030-family VMMC1 and VSIM regulators are fine (avoiding the
1234 * middle range) but VSIM can't power DAT4..DAT7 at more than 3V.
1235 */
1236 if ((1 << vdd) <= MMC_VDD_23_24)
1237 reg_val |= SDVS18;
1238 else
1239 reg_val |= SDVS30;
1240
1241 OMAP_HSMMC_WRITE(host->base, HCTL, reg_val);
1242 set_sd_bus_power(host);
1243
1244 return 0;
1245 err:
1246 dev_err(mmc_dev(host->mmc), "Unable to switch operating voltage\n");
1247 return ret;
1248 }
1249
1250 /* Protect the card while the cover is open */
1251 static void omap_hsmmc_protect_card(struct omap_hsmmc_host *host)
1252 {
1253 if (!host->get_cover_state)
1254 return;
1255
1256 host->reqs_blocked = 0;
1257 if (host->get_cover_state(host->dev)) {
1258 if (host->protect_card) {
1259 dev_info(host->dev, "%s: cover is closed, "
1260 "card is now accessible\n",
1261 mmc_hostname(host->mmc));
1262 host->protect_card = 0;
1263 }
1264 } else {
1265 if (!host->protect_card) {
1266 dev_info(host->dev, "%s: cover is open, "
1267 "card is now inaccessible\n",
1268 mmc_hostname(host->mmc));
1269 host->protect_card = 1;
1270 }
1271 }
1272 }
1273
1274 /*
1275 * irq handler when (cell-phone) cover is mounted/removed
1276 */
1277 static irqreturn_t omap_hsmmc_cover_irq(int irq, void *dev_id)
1278 {
1279 struct omap_hsmmc_host *host = dev_id;
1280
1281 sysfs_notify(&host->mmc->class_dev.kobj, NULL, "cover_switch");
1282
1283 omap_hsmmc_protect_card(host);
1284 mmc_detect_change(host->mmc, (HZ * 200) / 1000);
1285 return IRQ_HANDLED;
1286 }
1287
1288 static void omap_hsmmc_dma_callback(void *param)
1289 {
1290 struct omap_hsmmc_host *host = param;
1291 struct dma_chan *chan;
1292 struct mmc_data *data;
1293 int req_in_progress;
1294
1295 spin_lock_irq(&host->irq_lock);
1296 if (host->dma_ch < 0) {
1297 spin_unlock_irq(&host->irq_lock);
1298 return;
1299 }
1300
1301 data = host->mrq->data;
1302 chan = omap_hsmmc_get_dma_chan(host, data);
1303 if (!data->host_cookie)
1304 dma_unmap_sg(chan->device->dev,
1305 data->sg, data->sg_len,
1306 mmc_get_dma_dir(data));
1307
1308 req_in_progress = host->req_in_progress;
1309 host->dma_ch = -1;
1310 spin_unlock_irq(&host->irq_lock);
1311
1312 /* If DMA has finished after TC, complete the request */
1313 if (!req_in_progress) {
1314 struct mmc_request *mrq = host->mrq;
1315
1316 host->mrq = NULL;
1317 mmc_request_done(host->mmc, mrq);
1318 }
1319 }
1320
1321 static int omap_hsmmc_pre_dma_transfer(struct omap_hsmmc_host *host,
1322 struct mmc_data *data,
1323 struct omap_hsmmc_next *next,
1324 struct dma_chan *chan)
1325 {
1326 int dma_len;
1327
1328 if (!next && data->host_cookie &&
1329 data->host_cookie != host->next_data.cookie) {
1330 dev_warn(host->dev, "[%s] invalid cookie: data->host_cookie %d"
1331 " host->next_data.cookie %d\n",
1332 __func__, data->host_cookie, host->next_data.cookie);
1333 data->host_cookie = 0;
1334 }
1335
1336 /* Check if next job is already prepared */
1337 if (next || data->host_cookie != host->next_data.cookie) {
1338 dma_len = dma_map_sg(chan->device->dev, data->sg, data->sg_len,
1339 mmc_get_dma_dir(data));
1340
1341 } else {
1342 dma_len = host->next_data.dma_len;
1343 host->next_data.dma_len = 0;
1344 }
1345
1346
1347 if (dma_len == 0)
1348 return -EINVAL;
1349
1350 if (next) {
1351 next->dma_len = dma_len;
1352 data->host_cookie = ++next->cookie < 0 ? 1 : next->cookie;
1353 } else
1354 host->dma_len = dma_len;
1355
1356 return 0;
1357 }
1358
1359 /*
1360 * Routine to configure and start DMA for the MMC card
1361 */
1362 static int omap_hsmmc_setup_dma_transfer(struct omap_hsmmc_host *host,
1363 struct mmc_request *req)
1364 {
1365 struct dma_async_tx_descriptor *tx;
1366 int ret = 0, i;
1367 struct mmc_data *data = req->data;
1368 struct dma_chan *chan;
1369 struct dma_slave_config cfg = {
1370 .src_addr = host->mapbase + OMAP_HSMMC_DATA,
1371 .dst_addr = host->mapbase + OMAP_HSMMC_DATA,
1372 .src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
1373 .dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES,
1374 .src_maxburst = data->blksz / 4,
1375 .dst_maxburst = data->blksz / 4,
1376 };
1377
1378 /* Sanity check: all the SG entries must be aligned by block size. */
1379 for (i = 0; i < data->sg_len; i++) {
1380 struct scatterlist *sgl;
1381
1382 sgl = data->sg + i;
1383 if (sgl->length % data->blksz)
1384 return -EINVAL;
1385 }
1386 if ((data->blksz % 4) != 0)
1387 /* REVISIT: The MMC buffer increments only when MSB is written.
1388 * Return error for blksz which is non multiple of four.
1389 */
1390 return -EINVAL;
1391
1392 BUG_ON(host->dma_ch != -1);
1393
1394 chan = omap_hsmmc_get_dma_chan(host, data);
1395
1396 ret = dmaengine_slave_config(chan, &cfg);
1397 if (ret)
1398 return ret;
1399
1400 ret = omap_hsmmc_pre_dma_transfer(host, data, NULL, chan);
1401 if (ret)
1402 return ret;
1403
1404 tx = dmaengine_prep_slave_sg(chan, data->sg, data->sg_len,
1405 data->flags & MMC_DATA_WRITE ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM,
1406 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1407 if (!tx) {
1408 dev_err(mmc_dev(host->mmc), "prep_slave_sg() failed\n");
1409 /* FIXME: cleanup */
1410 return -1;
1411 }
1412
1413 tx->callback = omap_hsmmc_dma_callback;
1414 tx->callback_param = host;
1415
1416 /* Does not fail */
1417 dmaengine_submit(tx);
1418
1419 host->dma_ch = 1;
1420
1421 return 0;
1422 }
1423
1424 static void set_data_timeout(struct omap_hsmmc_host *host,
1425 unsigned long long timeout_ns,
1426 unsigned int timeout_clks)
1427 {
1428 unsigned long long timeout = timeout_ns;
1429 unsigned int cycle_ns;
1430 uint32_t reg, clkd, dto = 0;
1431
1432 reg = OMAP_HSMMC_READ(host->base, SYSCTL);
1433 clkd = (reg & CLKD_MASK) >> CLKD_SHIFT;
1434 if (clkd == 0)
1435 clkd = 1;
1436
1437 cycle_ns = 1000000000 / (host->clk_rate / clkd);
1438 do_div(timeout, cycle_ns);
1439 timeout += timeout_clks;
1440 if (timeout) {
1441 while ((timeout & 0x80000000) == 0) {
1442 dto += 1;
1443 timeout <<= 1;
1444 }
1445 dto = 31 - dto;
1446 timeout <<= 1;
1447 if (timeout && dto)
1448 dto += 1;
1449 if (dto >= 13)
1450 dto -= 13;
1451 else
1452 dto = 0;
1453 if (dto > 14)
1454 dto = 14;
1455 }
1456
1457 reg &= ~DTO_MASK;
1458 reg |= dto << DTO_SHIFT;
1459 OMAP_HSMMC_WRITE(host->base, SYSCTL, reg);
1460 }
1461
1462 static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host)
1463 {
1464 struct mmc_request *req = host->mrq;
1465 struct dma_chan *chan;
1466
1467 if (!req->data)
1468 return;
1469 OMAP_HSMMC_WRITE(host->base, BLK, (req->data->blksz)
1470 | (req->data->blocks << 16));
1471 set_data_timeout(host, req->data->timeout_ns,
1472 req->data->timeout_clks);
1473 chan = omap_hsmmc_get_dma_chan(host, req->data);
1474 dma_async_issue_pending(chan);
1475 }
1476
1477 /*
1478 * Configure block length for MMC/SD cards and initiate the transfer.
1479 */
1480 static int
1481 omap_hsmmc_prepare_data(struct omap_hsmmc_host *host, struct mmc_request *req)
1482 {
1483 int ret;
1484 unsigned long long timeout;
1485
1486 host->data = req->data;
1487
1488 if (req->data == NULL) {
1489 OMAP_HSMMC_WRITE(host->base, BLK, 0);
1490 if (req->cmd->flags & MMC_RSP_BUSY) {
1491 timeout = req->cmd->busy_timeout * NSEC_PER_MSEC;
1492
1493 /*
1494 * Set an arbitrary 100ms data timeout for commands with
1495 * busy signal and no indication of busy_timeout.
1496 */
1497 if (!timeout)
1498 timeout = 100000000U;
1499
1500 set_data_timeout(host, timeout, 0);
1501 }
1502 return 0;
1503 }
1504
1505 if (host->use_dma) {
1506 ret = omap_hsmmc_setup_dma_transfer(host, req);
1507 if (ret != 0) {
1508 dev_err(mmc_dev(host->mmc), "MMC start dma failure\n");
1509 return ret;
1510 }
1511 }
1512 return 0;
1513 }
1514
1515 static void omap_hsmmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
1516 int err)
1517 {
1518 struct omap_hsmmc_host *host = mmc_priv(mmc);
1519 struct mmc_data *data = mrq->data;
1520
1521 if (host->use_dma && data->host_cookie) {
1522 struct dma_chan *c = omap_hsmmc_get_dma_chan(host, data);
1523
1524 dma_unmap_sg(c->device->dev, data->sg, data->sg_len,
1525 mmc_get_dma_dir(data));
1526 data->host_cookie = 0;
1527 }
1528 }
1529
1530 static void omap_hsmmc_pre_req(struct mmc_host *mmc, struct mmc_request *mrq)
1531 {
1532 struct omap_hsmmc_host *host = mmc_priv(mmc);
1533
1534 if (mrq->data->host_cookie) {
1535 mrq->data->host_cookie = 0;
1536 return ;
1537 }
1538
1539 if (host->use_dma) {
1540 struct dma_chan *c = omap_hsmmc_get_dma_chan(host, mrq->data);
1541
1542 if (omap_hsmmc_pre_dma_transfer(host, mrq->data,
1543 &host->next_data, c))
1544 mrq->data->host_cookie = 0;
1545 }
1546 }
1547
1548 /*
1549 * Request function. for read/write operation
1550 */
1551 static void omap_hsmmc_request(struct mmc_host *mmc, struct mmc_request *req)
1552 {
1553 struct omap_hsmmc_host *host = mmc_priv(mmc);
1554 int err;
1555
1556 BUG_ON(host->req_in_progress);
1557 BUG_ON(host->dma_ch != -1);
1558 if (host->protect_card) {
1559 if (host->reqs_blocked < 3) {
1560 /*
1561 * Ensure the controller is left in a consistent
1562 * state by resetting the command and data state
1563 * machines.
1564 */
1565 omap_hsmmc_reset_controller_fsm(host, SRD);
1566 omap_hsmmc_reset_controller_fsm(host, SRC);
1567 host->reqs_blocked += 1;
1568 }
1569 req->cmd->error = -EBADF;
1570 if (req->data)
1571 req->data->error = -EBADF;
1572 req->cmd->retries = 0;
1573 mmc_request_done(mmc, req);
1574 return;
1575 } else if (host->reqs_blocked)
1576 host->reqs_blocked = 0;
1577 WARN_ON(host->mrq != NULL);
1578 host->mrq = req;
1579 host->clk_rate = clk_get_rate(host->fclk);
1580 err = omap_hsmmc_prepare_data(host, req);
1581 if (err) {
1582 req->cmd->error = err;
1583 if (req->data)
1584 req->data->error = err;
1585 host->mrq = NULL;
1586 mmc_request_done(mmc, req);
1587 return;
1588 }
1589 if (req->sbc && !(host->flags & AUTO_CMD23)) {
1590 omap_hsmmc_start_command(host, req->sbc, NULL);
1591 return;
1592 }
1593
1594 omap_hsmmc_start_dma_transfer(host);
1595 omap_hsmmc_start_command(host, req->cmd, req->data);
1596 }
1597
1598 /* Routine to configure clock values. Exposed API to core */
1599 static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1600 {
1601 struct omap_hsmmc_host *host = mmc_priv(mmc);
1602 int do_send_init_stream = 0;
1603
1604 if (ios->power_mode != host->power_mode) {
1605 switch (ios->power_mode) {
1606 case MMC_POWER_OFF:
1607 omap_hsmmc_set_power(host, 0);
1608 break;
1609 case MMC_POWER_UP:
1610 omap_hsmmc_set_power(host, 1);
1611 break;
1612 case MMC_POWER_ON:
1613 do_send_init_stream = 1;
1614 break;
1615 }
1616 host->power_mode = ios->power_mode;
1617 }
1618
1619 /* FIXME: set registers based only on changes to ios */
1620
1621 omap_hsmmc_set_bus_width(host);
1622
1623 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
1624 /* Only MMC1 can interface at 3V without some flavor
1625 * of external transceiver; but they all handle 1.8V.
1626 */
1627 if ((OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET) &&
1628 (ios->vdd == DUAL_VOLT_OCR_BIT)) {
1629 /*
1630 * The mmc_select_voltage fn of the core does
1631 * not seem to set the power_mode to
1632 * MMC_POWER_UP upon recalculating the voltage.
1633 * vdd 1.8v.
1634 */
1635 if (omap_hsmmc_switch_opcond(host, ios->vdd) != 0)
1636 dev_dbg(mmc_dev(host->mmc),
1637 "Switch operation failed\n");
1638 }
1639 }
1640
1641 omap_hsmmc_set_clock(host);
1642
1643 if (do_send_init_stream)
1644 send_init_stream(host);
1645
1646 omap_hsmmc_set_bus_mode(host);
1647 }
1648
1649 static int omap_hsmmc_get_cd(struct mmc_host *mmc)
1650 {
1651 struct omap_hsmmc_host *host = mmc_priv(mmc);
1652
1653 if (!host->card_detect)
1654 return -ENOSYS;
1655 return host->card_detect(host->dev);
1656 }
1657
1658 static void omap_hsmmc_init_card(struct mmc_host *mmc, struct mmc_card *card)
1659 {
1660 struct omap_hsmmc_host *host = mmc_priv(mmc);
1661
1662 if (mmc_pdata(host)->init_card)
1663 mmc_pdata(host)->init_card(card);
1664 else if (card->type == MMC_TYPE_SDIO ||
1665 card->type == MMC_TYPE_SD_COMBO) {
1666 struct device_node *np = mmc_dev(mmc)->of_node;
1667
1668 /*
1669 * REVISIT: should be moved to sdio core and made more
1670 * general e.g. by expanding the DT bindings of child nodes
1671 * to provide a mechanism to provide this information:
1672 * Documentation/devicetree/bindings/mmc/mmc-card.txt
1673 */
1674
1675 np = of_get_compatible_child(np, "ti,wl1251");
1676 if (np) {
1677 /*
1678 * We have TI wl1251 attached to MMC3. Pass this
1679 * information to the SDIO core because it can't be
1680 * probed by normal methods.
1681 */
1682
1683 dev_info(host->dev, "found wl1251\n");
1684 card->quirks |= MMC_QUIRK_NONSTD_SDIO;
1685 card->cccr.wide_bus = 1;
1686 card->cis.vendor = 0x104c;
1687 card->cis.device = 0x9066;
1688 card->cis.blksize = 512;
1689 card->cis.max_dtr = 24000000;
1690 card->ocr = 0x80;
1691 of_node_put(np);
1692 }
1693 }
1694 }
1695
1696 static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
1697 {
1698 struct omap_hsmmc_host *host = mmc_priv(mmc);
1699 u32 irq_mask, con;
1700 unsigned long flags;
1701
1702 spin_lock_irqsave(&host->irq_lock, flags);
1703
1704 con = OMAP_HSMMC_READ(host->base, CON);
1705 irq_mask = OMAP_HSMMC_READ(host->base, ISE);
1706 if (enable) {
1707 host->flags |= HSMMC_SDIO_IRQ_ENABLED;
1708 irq_mask |= CIRQ_EN;
1709 con |= CTPL | CLKEXTFREE;
1710 } else {
1711 host->flags &= ~HSMMC_SDIO_IRQ_ENABLED;
1712 irq_mask &= ~CIRQ_EN;
1713 con &= ~(CTPL | CLKEXTFREE);
1714 }
1715 OMAP_HSMMC_WRITE(host->base, CON, con);
1716 OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
1717
1718 /*
1719 * if enable, piggy back detection on current request
1720 * but always disable immediately
1721 */
1722 if (!host->req_in_progress || !enable)
1723 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
1724
1725 /* flush posted write */
1726 OMAP_HSMMC_READ(host->base, IE);
1727
1728 spin_unlock_irqrestore(&host->irq_lock, flags);
1729 }
1730
1731 static int omap_hsmmc_configure_wake_irq(struct omap_hsmmc_host *host)
1732 {
1733 int ret;
1734
1735 /*
1736 * For omaps with wake-up path, wakeirq will be irq from pinctrl and
1737 * for other omaps, wakeirq will be from GPIO (dat line remuxed to
1738 * gpio). wakeirq is needed to detect sdio irq in runtime suspend state
1739 * with functional clock disabled.
1740 */
1741 if (!host->dev->of_node || !host->wake_irq)
1742 return -ENODEV;
1743
1744 ret = dev_pm_set_dedicated_wake_irq(host->dev, host->wake_irq);
1745 if (ret) {
1746 dev_err(mmc_dev(host->mmc), "Unable to request wake IRQ\n");
1747 goto err;
1748 }
1749
1750 /*
1751 * Some omaps don't have wake-up path from deeper idle states
1752 * and need to remux SDIO DAT1 to GPIO for wake-up from idle.
1753 */
1754 if (host->pdata->controller_flags & OMAP_HSMMC_SWAKEUP_MISSING) {
1755 struct pinctrl *p = devm_pinctrl_get(host->dev);
1756 if (IS_ERR(p)) {
1757 ret = PTR_ERR(p);
1758 goto err_free_irq;
1759 }
1760 if (IS_ERR(pinctrl_lookup_state(p, PINCTRL_STATE_DEFAULT))) {
1761 dev_info(host->dev, "missing default pinctrl state\n");
1762 devm_pinctrl_put(p);
1763 ret = -EINVAL;
1764 goto err_free_irq;
1765 }
1766
1767 if (IS_ERR(pinctrl_lookup_state(p, PINCTRL_STATE_IDLE))) {
1768 dev_info(host->dev, "missing idle pinctrl state\n");
1769 devm_pinctrl_put(p);
1770 ret = -EINVAL;
1771 goto err_free_irq;
1772 }
1773 devm_pinctrl_put(p);
1774 }
1775
1776 OMAP_HSMMC_WRITE(host->base, HCTL,
1777 OMAP_HSMMC_READ(host->base, HCTL) | IWE);
1778 return 0;
1779
1780 err_free_irq:
1781 dev_pm_clear_wake_irq(host->dev);
1782 err:
1783 dev_warn(host->dev, "no SDIO IRQ support, falling back to polling\n");
1784 host->wake_irq = 0;
1785 return ret;
1786 }
1787
1788 static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host)
1789 {
1790 u32 hctl, capa, value;
1791
1792 /* Only MMC1 supports 3.0V */
1793 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
1794 hctl = SDVS30;
1795 capa = VS30 | VS18;
1796 } else {
1797 hctl = SDVS18;
1798 capa = VS18;
1799 }
1800
1801 value = OMAP_HSMMC_READ(host->base, HCTL) & ~SDVS_MASK;
1802 OMAP_HSMMC_WRITE(host->base, HCTL, value | hctl);
1803
1804 value = OMAP_HSMMC_READ(host->base, CAPA);
1805 OMAP_HSMMC_WRITE(host->base, CAPA, value | capa);
1806
1807 /* Set SD bus power bit */
1808 set_sd_bus_power(host);
1809 }
1810
1811 static int omap_hsmmc_multi_io_quirk(struct mmc_card *card,
1812 unsigned int direction, int blk_size)
1813 {
1814 /* This controller can't do multiblock reads due to hw bugs */
1815 if (direction == MMC_DATA_READ)
1816 return 1;
1817
1818 return blk_size;
1819 }
1820
1821 static struct mmc_host_ops omap_hsmmc_ops = {
1822 .post_req = omap_hsmmc_post_req,
1823 .pre_req = omap_hsmmc_pre_req,
1824 .request = omap_hsmmc_request,
1825 .set_ios = omap_hsmmc_set_ios,
1826 .get_cd = omap_hsmmc_get_cd,
1827 .get_ro = mmc_gpio_get_ro,
1828 .init_card = omap_hsmmc_init_card,
1829 .enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
1830 };
1831
1832 #ifdef CONFIG_DEBUG_FS
1833
1834 static int omap_hsmmc_regs_show(struct seq_file *s, void *data)
1835 {
1836 struct mmc_host *mmc = s->private;
1837 struct omap_hsmmc_host *host = mmc_priv(mmc);
1838
1839 seq_printf(s, "mmc%d:\n", mmc->index);
1840 seq_printf(s, "sdio irq mode\t%s\n",
1841 (mmc->caps & MMC_CAP_SDIO_IRQ) ? "interrupt" : "polling");
1842
1843 if (mmc->caps & MMC_CAP_SDIO_IRQ) {
1844 seq_printf(s, "sdio irq \t%s\n",
1845 (host->flags & HSMMC_SDIO_IRQ_ENABLED) ? "enabled"
1846 : "disabled");
1847 }
1848 seq_printf(s, "ctx_loss:\t%d\n", host->context_loss);
1849
1850 pm_runtime_get_sync(host->dev);
1851 seq_puts(s, "\nregs:\n");
1852 seq_printf(s, "CON:\t\t0x%08x\n",
1853 OMAP_HSMMC_READ(host->base, CON));
1854 seq_printf(s, "PSTATE:\t\t0x%08x\n",
1855 OMAP_HSMMC_READ(host->base, PSTATE));
1856 seq_printf(s, "HCTL:\t\t0x%08x\n",
1857 OMAP_HSMMC_READ(host->base, HCTL));
1858 seq_printf(s, "SYSCTL:\t\t0x%08x\n",
1859 OMAP_HSMMC_READ(host->base, SYSCTL));
1860 seq_printf(s, "IE:\t\t0x%08x\n",
1861 OMAP_HSMMC_READ(host->base, IE));
1862 seq_printf(s, "ISE:\t\t0x%08x\n",
1863 OMAP_HSMMC_READ(host->base, ISE));
1864 seq_printf(s, "CAPA:\t\t0x%08x\n",
1865 OMAP_HSMMC_READ(host->base, CAPA));
1866
1867 pm_runtime_mark_last_busy(host->dev);
1868 pm_runtime_put_autosuspend(host->dev);
1869
1870 return 0;
1871 }
1872
1873 static int omap_hsmmc_regs_open(struct inode *inode, struct file *file)
1874 {
1875 return single_open(file, omap_hsmmc_regs_show, inode->i_private);
1876 }
1877
1878 static const struct file_operations mmc_regs_fops = {
1879 .open = omap_hsmmc_regs_open,
1880 .read = seq_read,
1881 .llseek = seq_lseek,
1882 .release = single_release,
1883 };
1884
1885 static void omap_hsmmc_debugfs(struct mmc_host *mmc)
1886 {
1887 if (mmc->debugfs_root)
1888 debugfs_create_file("regs", S_IRUSR, mmc->debugfs_root,
1889 mmc, &mmc_regs_fops);
1890 }
1891
1892 #else
1893
1894 static void omap_hsmmc_debugfs(struct mmc_host *mmc)
1895 {
1896 }
1897
1898 #endif
1899
1900 #ifdef CONFIG_OF
1901 static const struct omap_mmc_of_data omap3_pre_es3_mmc_of_data = {
1902 /* See 35xx errata 2.1.1.128 in SPRZ278F */
1903 .controller_flags = OMAP_HSMMC_BROKEN_MULTIBLOCK_READ,
1904 };
1905
1906 static const struct omap_mmc_of_data omap4_mmc_of_data = {
1907 .reg_offset = 0x100,
1908 };
1909 static const struct omap_mmc_of_data am33xx_mmc_of_data = {
1910 .reg_offset = 0x100,
1911 .controller_flags = OMAP_HSMMC_SWAKEUP_MISSING,
1912 };
1913
1914 static const struct of_device_id omap_mmc_of_match[] = {
1915 {
1916 .compatible = "ti,omap2-hsmmc",
1917 },
1918 {
1919 .compatible = "ti,omap3-pre-es3-hsmmc",
1920 .data = &omap3_pre_es3_mmc_of_data,
1921 },
1922 {
1923 .compatible = "ti,omap3-hsmmc",
1924 },
1925 {
1926 .compatible = "ti,omap4-hsmmc",
1927 .data = &omap4_mmc_of_data,
1928 },
1929 {
1930 .compatible = "ti,am33xx-hsmmc",
1931 .data = &am33xx_mmc_of_data,
1932 },
1933 {},
1934 };
1935 MODULE_DEVICE_TABLE(of, omap_mmc_of_match);
1936
1937 static struct omap_hsmmc_platform_data *of_get_hsmmc_pdata(struct device *dev)
1938 {
1939 struct omap_hsmmc_platform_data *pdata, *legacy;
1940 struct device_node *np = dev->of_node;
1941
1942 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
1943 if (!pdata)
1944 return ERR_PTR(-ENOMEM); /* out of memory */
1945
1946 legacy = dev_get_platdata(dev);
1947 if (legacy && legacy->name)
1948 pdata->name = legacy->name;
1949
1950 if (of_find_property(np, "ti,dual-volt", NULL))
1951 pdata->controller_flags |= OMAP_HSMMC_SUPPORTS_DUAL_VOLT;
1952
1953 pdata->gpio_cd = -EINVAL;
1954 pdata->gpio_cod = -EINVAL;
1955 pdata->gpio_wp = -EINVAL;
1956
1957 if (of_find_property(np, "ti,non-removable", NULL)) {
1958 pdata->nonremovable = true;
1959 pdata->no_regulator_off_init = true;
1960 }
1961
1962 if (of_find_property(np, "ti,needs-special-reset", NULL))
1963 pdata->features |= HSMMC_HAS_UPDATED_RESET;
1964
1965 if (of_find_property(np, "ti,needs-special-hs-handling", NULL))
1966 pdata->features |= HSMMC_HAS_HSPE_SUPPORT;
1967
1968 return pdata;
1969 }
1970 #else
1971 static inline struct omap_hsmmc_platform_data
1972 *of_get_hsmmc_pdata(struct device *dev)
1973 {
1974 return ERR_PTR(-EINVAL);
1975 }
1976 #endif
1977
1978 static int omap_hsmmc_probe(struct platform_device *pdev)
1979 {
1980 struct omap_hsmmc_platform_data *pdata = pdev->dev.platform_data;
1981 struct mmc_host *mmc;
1982 struct omap_hsmmc_host *host = NULL;
1983 struct resource *res;
1984 int ret, irq;
1985 const struct of_device_id *match;
1986 const struct omap_mmc_of_data *data;
1987 void __iomem *base;
1988
1989 match = of_match_device(of_match_ptr(omap_mmc_of_match), &pdev->dev);
1990 if (match) {
1991 pdata = of_get_hsmmc_pdata(&pdev->dev);
1992
1993 if (IS_ERR(pdata))
1994 return PTR_ERR(pdata);
1995
1996 if (match->data) {
1997 data = match->data;
1998 pdata->reg_offset = data->reg_offset;
1999 pdata->controller_flags |= data->controller_flags;
2000 }
2001 }
2002
2003 if (pdata == NULL) {
2004 dev_err(&pdev->dev, "Platform Data is missing\n");
2005 return -ENXIO;
2006 }
2007
2008 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2009 irq = platform_get_irq(pdev, 0);
2010 if (res == NULL || irq < 0)
2011 return -ENXIO;
2012
2013 base = devm_ioremap_resource(&pdev->dev, res);
2014 if (IS_ERR(base))
2015 return PTR_ERR(base);
2016
2017 mmc = mmc_alloc_host(sizeof(struct omap_hsmmc_host), &pdev->dev);
2018 if (!mmc) {
2019 ret = -ENOMEM;
2020 goto err;
2021 }
2022
2023 ret = mmc_of_parse(mmc);
2024 if (ret)
2025 goto err1;
2026
2027 host = mmc_priv(mmc);
2028 host->mmc = mmc;
2029 host->pdata = pdata;
2030 host->dev = &pdev->dev;
2031 host->use_dma = 1;
2032 host->dma_ch = -1;
2033 host->irq = irq;
2034 host->mapbase = res->start + pdata->reg_offset;
2035 host->base = base + pdata->reg_offset;
2036 host->power_mode = MMC_POWER_OFF;
2037 host->next_data.cookie = 1;
2038 host->pbias_enabled = 0;
2039 host->vqmmc_enabled = 0;
2040
2041 ret = omap_hsmmc_gpio_init(mmc, host, pdata);
2042 if (ret)
2043 goto err_gpio;
2044
2045 platform_set_drvdata(pdev, host);
2046
2047 if (pdev->dev.of_node)
2048 host->wake_irq = irq_of_parse_and_map(pdev->dev.of_node, 1);
2049
2050 mmc->ops = &omap_hsmmc_ops;
2051
2052 mmc->f_min = OMAP_MMC_MIN_CLOCK;
2053
2054 if (pdata->max_freq > 0)
2055 mmc->f_max = pdata->max_freq;
2056 else if (mmc->f_max == 0)
2057 mmc->f_max = OMAP_MMC_MAX_CLOCK;
2058
2059 spin_lock_init(&host->irq_lock);
2060
2061 host->fclk = devm_clk_get(&pdev->dev, "fck");
2062 if (IS_ERR(host->fclk)) {
2063 ret = PTR_ERR(host->fclk);
2064 host->fclk = NULL;
2065 goto err1;
2066 }
2067
2068 if (host->pdata->controller_flags & OMAP_HSMMC_BROKEN_MULTIBLOCK_READ) {
2069 dev_info(&pdev->dev, "multiblock reads disabled due to 35xx erratum 2.1.1.128; MMC read performance may suffer\n");
2070 omap_hsmmc_ops.multi_io_quirk = omap_hsmmc_multi_io_quirk;
2071 }
2072
2073 device_init_wakeup(&pdev->dev, true);
2074 pm_runtime_enable(host->dev);
2075 pm_runtime_get_sync(host->dev);
2076 pm_runtime_set_autosuspend_delay(host->dev, MMC_AUTOSUSPEND_DELAY);
2077 pm_runtime_use_autosuspend(host->dev);
2078
2079 omap_hsmmc_context_save(host);
2080
2081 host->dbclk = devm_clk_get(&pdev->dev, "mmchsdb_fck");
2082 /*
2083 * MMC can still work without debounce clock.
2084 */
2085 if (IS_ERR(host->dbclk)) {
2086 host->dbclk = NULL;
2087 } else if (clk_prepare_enable(host->dbclk) != 0) {
2088 dev_warn(mmc_dev(host->mmc), "Failed to enable debounce clk\n");
2089 host->dbclk = NULL;
2090 }
2091
2092 /* Set this to a value that allows allocating an entire descriptor
2093 * list within a page (zero order allocation). */
2094 mmc->max_segs = 64;
2095
2096 mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
2097 mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
2098 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
2099
2100 mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
2101 MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_ERASE | MMC_CAP_CMD23;
2102
2103 mmc->caps |= mmc_pdata(host)->caps;
2104 if (mmc->caps & MMC_CAP_8_BIT_DATA)
2105 mmc->caps |= MMC_CAP_4_BIT_DATA;
2106
2107 if (mmc_pdata(host)->nonremovable)
2108 mmc->caps |= MMC_CAP_NONREMOVABLE;
2109
2110 mmc->pm_caps |= mmc_pdata(host)->pm_caps;
2111
2112 omap_hsmmc_conf_bus_power(host);
2113
2114 host->rx_chan = dma_request_chan(&pdev->dev, "rx");
2115 if (IS_ERR(host->rx_chan)) {
2116 dev_err(mmc_dev(host->mmc), "RX DMA channel request failed\n");
2117 ret = PTR_ERR(host->rx_chan);
2118 goto err_irq;
2119 }
2120
2121 host->tx_chan = dma_request_chan(&pdev->dev, "tx");
2122 if (IS_ERR(host->tx_chan)) {
2123 dev_err(mmc_dev(host->mmc), "TX DMA channel request failed\n");
2124 ret = PTR_ERR(host->tx_chan);
2125 goto err_irq;
2126 }
2127
2128 /*
2129 * Limit the maximum segment size to the lower of the request size
2130 * and the DMA engine device segment size limits. In reality, with
2131 * 32-bit transfers, the DMA engine can do longer segments than this
2132 * but there is no way to represent that in the DMA model - if we
2133 * increase this figure here, we get warnings from the DMA API debug.
2134 */
2135 mmc->max_seg_size = min3(mmc->max_req_size,
2136 dma_get_max_seg_size(host->rx_chan->device->dev),
2137 dma_get_max_seg_size(host->tx_chan->device->dev));
2138
2139 /* Request IRQ for MMC operations */
2140 ret = devm_request_irq(&pdev->dev, host->irq, omap_hsmmc_irq, 0,
2141 mmc_hostname(mmc), host);
2142 if (ret) {
2143 dev_err(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n");
2144 goto err_irq;
2145 }
2146
2147 ret = omap_hsmmc_reg_get(host);
2148 if (ret)
2149 goto err_irq;
2150
2151 if (!mmc->ocr_avail)
2152 mmc->ocr_avail = mmc_pdata(host)->ocr_mask;
2153
2154 omap_hsmmc_disable_irq(host);
2155
2156 /*
2157 * For now, only support SDIO interrupt if we have a separate
2158 * wake-up interrupt configured from device tree. This is because
2159 * the wake-up interrupt is needed for idle state and some
2160 * platforms need special quirks. And we don't want to add new
2161 * legacy mux platform init code callbacks any longer as we
2162 * are moving to DT based booting anyways.
2163 */
2164 ret = omap_hsmmc_configure_wake_irq(host);
2165 if (!ret)
2166 mmc->caps |= MMC_CAP_SDIO_IRQ;
2167
2168 omap_hsmmc_protect_card(host);
2169
2170 mmc_add_host(mmc);
2171
2172 if (mmc_pdata(host)->name != NULL) {
2173 ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name);
2174 if (ret < 0)
2175 goto err_slot_name;
2176 }
2177 if (host->get_cover_state) {
2178 ret = device_create_file(&mmc->class_dev,
2179 &dev_attr_cover_switch);
2180 if (ret < 0)
2181 goto err_slot_name;
2182 }
2183
2184 omap_hsmmc_debugfs(mmc);
2185 pm_runtime_mark_last_busy(host->dev);
2186 pm_runtime_put_autosuspend(host->dev);
2187
2188 return 0;
2189
2190 err_slot_name:
2191 mmc_remove_host(mmc);
2192 err_irq:
2193 device_init_wakeup(&pdev->dev, false);
2194 if (!IS_ERR_OR_NULL(host->tx_chan))
2195 dma_release_channel(host->tx_chan);
2196 if (!IS_ERR_OR_NULL(host->rx_chan))
2197 dma_release_channel(host->rx_chan);
2198 pm_runtime_dont_use_autosuspend(host->dev);
2199 pm_runtime_put_sync(host->dev);
2200 pm_runtime_disable(host->dev);
2201 if (host->dbclk)
2202 clk_disable_unprepare(host->dbclk);
2203 err1:
2204 err_gpio:
2205 mmc_free_host(mmc);
2206 err:
2207 return ret;
2208 }
2209
2210 static int omap_hsmmc_remove(struct platform_device *pdev)
2211 {
2212 struct omap_hsmmc_host *host = platform_get_drvdata(pdev);
2213
2214 pm_runtime_get_sync(host->dev);
2215 mmc_remove_host(host->mmc);
2216
2217 dma_release_channel(host->tx_chan);
2218 dma_release_channel(host->rx_chan);
2219
2220 dev_pm_clear_wake_irq(host->dev);
2221 pm_runtime_dont_use_autosuspend(host->dev);
2222 pm_runtime_put_sync(host->dev);
2223 pm_runtime_disable(host->dev);
2224 device_init_wakeup(&pdev->dev, false);
2225 if (host->dbclk)
2226 clk_disable_unprepare(host->dbclk);
2227
2228 mmc_free_host(host->mmc);
2229
2230 return 0;
2231 }
2232
2233 #ifdef CONFIG_PM_SLEEP
2234 static int omap_hsmmc_suspend(struct device *dev)
2235 {
2236 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
2237
2238 if (!host)
2239 return 0;
2240
2241 pm_runtime_get_sync(host->dev);
2242
2243 if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) {
2244 OMAP_HSMMC_WRITE(host->base, ISE, 0);
2245 OMAP_HSMMC_WRITE(host->base, IE, 0);
2246 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
2247 OMAP_HSMMC_WRITE(host->base, HCTL,
2248 OMAP_HSMMC_READ(host->base, HCTL) & ~SDBP);
2249 }
2250
2251 if (host->dbclk)
2252 clk_disable_unprepare(host->dbclk);
2253
2254 pm_runtime_put_sync(host->dev);
2255 return 0;
2256 }
2257
2258 /* Routine to resume the MMC device */
2259 static int omap_hsmmc_resume(struct device *dev)
2260 {
2261 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
2262
2263 if (!host)
2264 return 0;
2265
2266 pm_runtime_get_sync(host->dev);
2267
2268 if (host->dbclk)
2269 clk_prepare_enable(host->dbclk);
2270
2271 if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER))
2272 omap_hsmmc_conf_bus_power(host);
2273
2274 omap_hsmmc_protect_card(host);
2275 pm_runtime_mark_last_busy(host->dev);
2276 pm_runtime_put_autosuspend(host->dev);
2277 return 0;
2278 }
2279 #endif
2280
2281 static int omap_hsmmc_runtime_suspend(struct device *dev)
2282 {
2283 struct omap_hsmmc_host *host;
2284 unsigned long flags;
2285 int ret = 0;
2286
2287 host = platform_get_drvdata(to_platform_device(dev));
2288 omap_hsmmc_context_save(host);
2289 dev_dbg(dev, "disabled\n");
2290
2291 spin_lock_irqsave(&host->irq_lock, flags);
2292 if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
2293 (host->flags & HSMMC_SDIO_IRQ_ENABLED)) {
2294 /* disable sdio irq handling to prevent race */
2295 OMAP_HSMMC_WRITE(host->base, ISE, 0);
2296 OMAP_HSMMC_WRITE(host->base, IE, 0);
2297
2298 if (!(OMAP_HSMMC_READ(host->base, PSTATE) & DLEV_DAT(1))) {
2299 /*
2300 * dat1 line low, pending sdio irq
2301 * race condition: possible irq handler running on
2302 * multi-core, abort
2303 */
2304 dev_dbg(dev, "pending sdio irq, abort suspend\n");
2305 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
2306 OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
2307 OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
2308 pm_runtime_mark_last_busy(dev);
2309 ret = -EBUSY;
2310 goto abort;
2311 }
2312
2313 pinctrl_pm_select_idle_state(dev);
2314 } else {
2315 pinctrl_pm_select_idle_state(dev);
2316 }
2317
2318 abort:
2319 spin_unlock_irqrestore(&host->irq_lock, flags);
2320 return ret;
2321 }
2322
2323 static int omap_hsmmc_runtime_resume(struct device *dev)
2324 {
2325 struct omap_hsmmc_host *host;
2326 unsigned long flags;
2327
2328 host = platform_get_drvdata(to_platform_device(dev));
2329 omap_hsmmc_context_restore(host);
2330 dev_dbg(dev, "enabled\n");
2331
2332 spin_lock_irqsave(&host->irq_lock, flags);
2333 if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
2334 (host->flags & HSMMC_SDIO_IRQ_ENABLED)) {
2335
2336 pinctrl_pm_select_default_state(host->dev);
2337
2338 /* irq lost, if pinmux incorrect */
2339 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
2340 OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
2341 OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
2342 } else {
2343 pinctrl_pm_select_default_state(host->dev);
2344 }
2345 spin_unlock_irqrestore(&host->irq_lock, flags);
2346 return 0;
2347 }
2348
2349 static const struct dev_pm_ops omap_hsmmc_dev_pm_ops = {
2350 SET_SYSTEM_SLEEP_PM_OPS(omap_hsmmc_suspend, omap_hsmmc_resume)
2351 .runtime_suspend = omap_hsmmc_runtime_suspend,
2352 .runtime_resume = omap_hsmmc_runtime_resume,
2353 };
2354
2355 static struct platform_driver omap_hsmmc_driver = {
2356 .probe = omap_hsmmc_probe,
2357 .remove = omap_hsmmc_remove,
2358 .driver = {
2359 .name = DRIVER_NAME,
2360 .pm = &omap_hsmmc_dev_pm_ops,
2361 .of_match_table = of_match_ptr(omap_mmc_of_match),
2362 },
2363 };
2364
2365 module_platform_driver(omap_hsmmc_driver);
2366 MODULE_DESCRIPTION("OMAP High Speed Multimedia Card driver");
2367 MODULE_LICENSE("GPL");
2368 MODULE_ALIAS("platform:" DRIVER_NAME);
2369 MODULE_AUTHOR("Texas Instruments Inc");
Linux with added FPC-III support