drivers/ide/qd65xx.c

   1 /*
   2  *  Copyright (C) 1996-2001  Linus Torvalds & author (see below)
   3  */
   4
   5 /*
   6  *  Version 0.03        Cleaned auto-tune, added probe
   7  *  Version 0.04        Added second channel tuning
   8  *  Version 0.05        Enhanced tuning ; added qd6500 support
   9  *  Version 0.06        Added dos driver's list
  10  *  Version 0.07        Second channel bug fix
  11  *
  12  * QDI QD6500/QD6580 EIDE controller fast support
  13  *
  14  * To activate controller support, use "ide0=qd65xx"
  15  */
  16
  17 /*
  18  * Rewritten from the work of Colten Edwards <pje120@cs.usask.ca> by
  19  * Samuel Thibault <samuel.thibault@ens-lyon.org>
  20  */
  21
  22 #include <linux/module.h>
  23 #include <linux/types.h>
  24 #include <linux/kernel.h>
  25 #include <linux/delay.h>
  26 #include <linux/timer.h>
  27 #include <linux/mm.h>
  28 #include <linux/ioport.h>
  29 #include <linux/blkdev.h>
  30 #include <linux/ide.h>
  31 #include <linux/init.h>
  32 #include <asm/io.h>
  33
  34 #define DRV_NAME "qd65xx"
  35
  36 #include "qd65xx.h"
  37
  38 /*
  39  * I/O ports are 0x30-0x31 (and 0x32-0x33 for qd6580)
  40  *            or 0xb0-0xb1 (and 0xb2-0xb3 for qd6580)
  41  *      -- qd6500 is a single IDE interface
  42  *      -- qd6580 is a dual IDE interface
  43  *
  44  * More research on qd6580 being done by willmore@cig.mot.com (David)
  45  * More Information given by Petr Soucek (petr@ryston.cz)
  46  * http://www.ryston.cz/petr/vlb
  47  */
  48
  49 /*
  50  * base: Timer1
  51  *
  52  *
  53  * base+0x01: Config (R/O)
  54  *
  55  * bit 0: ide baseport: 1 = 0x1f0 ; 0 = 0x170 (only useful for qd6500)
  56  * bit 1: qd65xx baseport: 1 = 0xb0 ; 0 = 0x30
  57  * bit 2: ID3: bus speed: 1 = <=33MHz ; 0 = >33MHz
  58  * bit 3: qd6500: 1 = disabled, 0 = enabled
  59  *        qd6580: 1
  60  * upper nibble:
  61  *        qd6500: 1100
  62  *        qd6580: either 1010 or 0101
  63  *
  64  *
  65  * base+0x02: Timer2 (qd6580 only)
  66  *
  67  *
  68  * base+0x03: Control (qd6580 only)
  69  *
  70  * bits 0-3 must always be set 1
  71  * bit 4 must be set 1, but is set 0 by dos driver while measuring vlb clock
  72  * bit 0 : 1 = Only primary port enabled : channel 0 for hda, channel 1 for hdb
  73  *         0 = Primary and Secondary ports enabled : channel 0 for hda & hdb
  74  *                                                   channel 1 for hdc & hdd
  75  * bit 1 : 1 = only disks on primary port
  76  *         0 = disks & ATAPI devices on primary port
  77  * bit 2-4 : always 0
  78  * bit 5 : status, but of what ?
  79  * bit 6 : always set 1 by dos driver
  80  * bit 7 : set 1 for non-ATAPI devices on primary port
  81  *      (maybe read-ahead and post-write buffer ?)
  82  */
  83
  84 static int timings[4]={-1,-1,-1,-1}; /* stores current timing for each timer */
  85
  86 /*
  87  * qd65xx_select:
  88  *
  89  * This routine is invoked to prepare for access to a given drive.
  90  */
  91
  92 static void qd65xx_dev_select(ide_drive_t *drive)
  93 {
  94         u8 index = ((   (QD_TIMREG(drive)) & 0x80 ) >> 7) |
  95                         (QD_TIMREG(drive) & 0x02);
  96
  97         if (timings[index] != QD_TIMING(drive))
  98                 outb(timings[index] = QD_TIMING(drive), QD_TIMREG(drive));
  99
 100         outb(drive->select | ATA_DEVICE_OBS, drive->hwif->io_ports.device_addr);
 101 }
 102
 103 /*
 104  * qd6500_compute_timing
 105  *
 106  * computes the timing value where
 107  *      lower nibble represents active time,   in count of VLB clocks
 108  *      upper nibble represents recovery time, in count of VLB clocks
 109  */
 110
 111 static u8 qd6500_compute_timing (ide_hwif_t *hwif, int active_time, int recovery_time)
 112 {
 113         int clk = ide_vlb_clk ? ide_vlb_clk : 50;
 114         u8 act_cyc, rec_cyc;
 115
 116         if (clk <= 33) {
 117                 act_cyc =  9 - IDE_IN(active_time   * clk / 1000 + 1, 2,  9);
 118                 rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 0, 15);
 119         } else {
 120                 act_cyc =  8 - IDE_IN(active_time   * clk / 1000 + 1, 1,  8);
 121                 rec_cyc = 18 - IDE_IN(recovery_time * clk / 1000 + 1, 3, 18);
 122         }
 123
 124         return (rec_cyc << 4) | 0x08 | act_cyc;
 125 }
 126
 127 /*
 128  * qd6580_compute_timing
 129  *
 130  * idem for qd6580
 131  */
 132
 133 static u8 qd6580_compute_timing (int active_time, int recovery_time)
 134 {
 135         int clk = ide_vlb_clk ? ide_vlb_clk : 50;
 136         u8 act_cyc, rec_cyc;
 137
 138         act_cyc = 17 - IDE_IN(active_time   * clk / 1000 + 1, 2, 17);
 139         rec_cyc = 15 - IDE_IN(recovery_time * clk / 1000 + 1, 2, 15);
 140
 141         return (rec_cyc << 4) | act_cyc;
 142 }
 143
 144 /*
 145  * qd_find_disk_type
 146  *
 147  * tries to find timing from dos driver's table
 148  */
 149
 150 static int qd_find_disk_type (ide_drive_t *drive,
 151                 int *active_time, int *recovery_time)
 152 {
 153         struct qd65xx_timing_s *p;
 154         char *m = (char *)&drive->id[ATA_ID_PROD];
 155         char model[ATA_ID_PROD_LEN];
 156
 157         if (*m == 0)
 158                 return 0;
 159
 160         strncpy(model, m, ATA_ID_PROD_LEN);
 161         ide_fixstring(model, ATA_ID_PROD_LEN, 1); /* byte-swap */
 162
 163         for (p = qd65xx_timing ; p->offset != -1 ; p++) {
 164                 if (!strncmp(p->model, model+p->offset, 4)) {
 165                         printk(KERN_DEBUG "%s: listed !\n", drive->name);
 166                         *active_time = p->active;
 167                         *recovery_time = p->recovery;
 168                         return 1;
 169                 }
 170         }
 171         return 0;
 172 }
 173
 174 /*
 175  * qd_set_timing:
 176  *
 177  * records the timing
 178  */
 179
 180 static void qd_set_timing (ide_drive_t *drive, u8 timing)
 181 {
 182         unsigned long data = (unsigned long)ide_get_drivedata(drive);
 183
 184         data &= 0xff00;
 185         data |= timing;
 186         ide_set_drivedata(drive, (void *)data);
 187
 188         printk(KERN_DEBUG "%s: %#x\n", drive->name, timing);
 189 }
 190
 191 static void qd6500_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 192 {
 193         u16 *id = drive->id;
 194         int active_time   = 175;
 195         int recovery_time = 415; /* worst case values from the dos driver */
 196
 197         /* FIXME: use drive->pio_mode value */
 198         if (!qd_find_disk_type(drive, &active_time, &recovery_time) &&
 199             (id[ATA_ID_OLD_PIO_MODES] & 0xff) && (id[ATA_ID_FIELD_VALID] & 2) &&
 200             id[ATA_ID_EIDE_PIO] >= 240) {
 201                 printk(KERN_INFO "%s: PIO mode%d\n", drive->name,
 202                         id[ATA_ID_OLD_PIO_MODES] & 0xff);
 203                 active_time = 110;
 204                 recovery_time = drive->id[ATA_ID_EIDE_PIO] - 120;
 205         }
 206
 207         qd_set_timing(drive, qd6500_compute_timing(drive->hwif,
 208                                 active_time, recovery_time));
 209 }
 210
 211 static void qd6580_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
 212 {
 213         const u8 pio = drive->pio_mode - XFER_PIO_0;
 214         struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 215         unsigned int cycle_time;
 216         int active_time   = 175;
 217         int recovery_time = 415; /* worst case values from the dos driver */
 218         u8 base = (hwif->config_data & 0xff00) >> 8;
 219
 220         if (drive->id && !qd_find_disk_type(drive, &active_time, &recovery_time)) {
 221                 cycle_time = ide_pio_cycle_time(drive, pio);
 222
 223                 switch (pio) {
 224                         case 0: break;
 225                         case 3:
 226                                 if (cycle_time >= 110) {
 227                                         active_time = 86;
 228                                         recovery_time = cycle_time - 102;
 229                                 } else
 230                                         printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
 231                                 break;
 232                         case 4:
 233                                 if (cycle_time >= 69) {
 234                                         active_time = 70;
 235                                         recovery_time = cycle_time - 61;
 236                                 } else
 237                                         printk(KERN_WARNING "%s: Strange recovery time !\n",drive->name);
 238                                 break;
 239                         default:
 240                                 if (cycle_time >= 180) {
 241                                         active_time = 110;
 242                                         recovery_time = cycle_time - 120;
 243                                 } else {
 244                                         active_time = t->active;
 245                                         recovery_time = cycle_time - active_time;
 246                                 }
 247                 }
 248                 printk(KERN_INFO "%s: PIO mode%d\n", drive->name,pio);
 249         }
 250
 251         if (!hwif->channel && drive->media != ide_disk) {
 252                 outb(0x5f, QD_CONTROL_PORT);
 253                 printk(KERN_WARNING "%s: ATAPI: disabled read-ahead FIFO "
 254                         "and post-write buffer on %s.\n",
 255                         drive->name, hwif->name);
 256         }
 257
 258         qd_set_timing(drive, qd6580_compute_timing(active_time, recovery_time));
 259 }
 260
 261 /*
 262  * qd_testreg
 263  *
 264  * tests if the given port is a register
 265  */
 266
 267 static int __init qd_testreg(int port)
 268 {
 269         unsigned long flags;
 270         u8 savereg, readreg;
 271
 272         local_irq_save(flags);
 273         savereg = inb_p(port);
 274         outb_p(QD_TESTVAL, port);       /* safe value */
 275         readreg = inb_p(port);
 276         outb(savereg, port);
 277         local_irq_restore(flags);
 278
 279         if (savereg == QD_TESTVAL) {
 280                 printk(KERN_ERR "Outch ! the probe for qd65xx isn't reliable !\n");
 281                 printk(KERN_ERR "Please contact maintainers to tell about your hardware\n");
 282                 printk(KERN_ERR "Assuming qd65xx is not present.\n");
 283                 return 1;
 284         }
 285
 286         return (readreg != QD_TESTVAL);
 287 }
 288
 289 static void __init qd6500_init_dev(ide_drive_t *drive)
 290 {
 291         ide_hwif_t *hwif = drive->hwif;
 292         u8 base = (hwif->config_data & 0xff00) >> 8;
 293         u8 config = QD_CONFIG(hwif);
 294
 295         ide_set_drivedata(drive, (void *)QD6500_DEF_DATA);
 296 }
 297
 298 static void __init qd6580_init_dev(ide_drive_t *drive)
 299 {
 300         ide_hwif_t *hwif = drive->hwif;
 301         u16 t1, t2;
 302         u8 base = (hwif->config_data & 0xff00) >> 8;
 303         u8 config = QD_CONFIG(hwif);
 304
 305         if (hwif->host_flags & IDE_HFLAG_SINGLE) {
 306                 t1 = QD6580_DEF_DATA;
 307                 t2 = QD6580_DEF_DATA2;
 308         } else
 309                 t2 = t1 = hwif->channel ? QD6580_DEF_DATA2 : QD6580_DEF_DATA;
 310
 311         ide_set_drivedata(drive, (void *)((drive->dn & 1) ? t2 : t1));
 312 }
 313
 314 static const struct ide_tp_ops qd65xx_tp_ops = {
 315         .exec_command           = ide_exec_command,
 316         .read_status            = ide_read_status,
 317         .read_altstatus         = ide_read_altstatus,
 318         .write_devctl           = ide_write_devctl,
 319
 320         .dev_select             = qd65xx_dev_select,
 321         .tf_load                = ide_tf_load,
 322         .tf_read                = ide_tf_read,
 323
 324         .input_data             = ide_input_data,
 325         .output_data            = ide_output_data,
 326 };
 327
 328 static const struct ide_port_ops qd6500_port_ops = {
 329         .init_dev               = qd6500_init_dev,
 330         .set_pio_mode           = qd6500_set_pio_mode,
 331 };
 332
 333 static const struct ide_port_ops qd6580_port_ops = {
 334         .init_dev               = qd6580_init_dev,
 335         .set_pio_mode           = qd6580_set_pio_mode,
 336 };
 337
 338 static const struct ide_port_info qd65xx_port_info __initconst = {
 339         .name                   = DRV_NAME,
 340         .tp_ops                 = &qd65xx_tp_ops,
 341         .chipset                = ide_qd65xx,
 342         .host_flags             = IDE_HFLAG_IO_32BIT |
 343                                   IDE_HFLAG_NO_DMA,
 344         .pio_mask               = ATA_PIO4,
 345 };
 346
 347 /*
 348  * qd_probe:
 349  *
 350  * looks at the specified baseport, and if qd found, registers & initialises it
 351  * return 1 if another qd may be probed
 352  */
 353
 354 static int __init qd_probe(int base)
 355 {
 356         int rc;
 357         u8 config, unit, control;
 358         struct ide_port_info d = qd65xx_port_info;
 359
 360         config = inb(QD_CONFIG_PORT);
 361
 362         if (! ((config & QD_CONFIG_BASEPORT) >> 1 == (base == 0xb0)) )
 363                 return -ENODEV;
 364
 365         unit = ! (config & QD_CONFIG_IDE_BASEPORT);
 366
 367         if (unit)
 368                 d.host_flags |= IDE_HFLAG_QD_2ND_PORT;
 369
 370         switch (config & 0xf0) {
 371         case QD_CONFIG_QD6500:
 372                 if (qd_testreg(base))
 373                          return -ENODEV;        /* bad register */
 374
 375                 if (config & QD_CONFIG_DISABLED) {
 376                         printk(KERN_WARNING "qd6500 is disabled !\n");
 377                         return -ENODEV;
 378                 }
 379
 380                 printk(KERN_NOTICE "qd6500 at %#x\n", base);
 381                 printk(KERN_DEBUG "qd6500: config=%#x, ID3=%u\n",
 382                         config, QD_ID3);
 383
 384                 d.port_ops = &qd6500_port_ops;
 385                 d.host_flags |= IDE_HFLAG_SINGLE;
 386                 break;
 387         case QD_CONFIG_QD6580_A:
 388         case QD_CONFIG_QD6580_B:
 389                 if (qd_testreg(base) || qd_testreg(base + 0x02))
 390                         return -ENODEV; /* bad registers */
 391
 392                 control = inb(QD_CONTROL_PORT);
 393
 394                 printk(KERN_NOTICE "qd6580 at %#x\n", base);
 395                 printk(KERN_DEBUG "qd6580: config=%#x, control=%#x, ID3=%u\n",
 396                         config, control, QD_ID3);
 397
 398                 outb(QD_DEF_CONTR, QD_CONTROL_PORT);
 399
 400                 d.port_ops = &qd6580_port_ops;
 401                 if (control & QD_CONTR_SEC_DISABLED)
 402                         d.host_flags |= IDE_HFLAG_SINGLE;
 403
 404                 printk(KERN_INFO "qd6580: %s IDE board\n",
 405                         (control & QD_CONTR_SEC_DISABLED) ? "single" : "dual");
 406                 break;
 407         default:
 408                 return -ENODEV;
 409         }
 410
 411         rc = ide_legacy_device_add(&d, (base << 8) | config);
 412
 413         if (d.host_flags & IDE_HFLAG_SINGLE)
 414                 return (rc == 0) ? 1 : rc;
 415
 416         return rc;
 417 }
 418
 419 static bool probe_qd65xx;
 420
 421 module_param_named(probe, probe_qd65xx, bool, 0);
 422 MODULE_PARM_DESC(probe, "probe for QD65xx chipsets");
 423
 424 static int __init qd65xx_init(void)
 425 {
 426         int rc1, rc2 = -ENODEV;
 427
 428         if (probe_qd65xx == 0)
 429                 return -ENODEV;
 430
 431         rc1 = qd_probe(0x30);
 432         if (rc1)
 433                 rc2 = qd_probe(0xb0);
 434
 435         if (rc1 < 0 && rc2 < 0)
 436                 return -ENODEV;
 437
 438         return 0;
 439 }
 440
 441 module_init(qd65xx_init);
 442
 443 MODULE_AUTHOR("Samuel Thibault");
 444 MODULE_DESCRIPTION("support of qd65xx vlb ide chipset");
 445 MODULE_LICENSE("GPL");