WIP FPC-III support
[linux/fpc-iii.git] / drivers / mtd / nand / raw / nand_bbt.c
blobdced32a126d93b373e63031cdef4bfa4afc2e3d8
1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Overview:
4 * Bad block table support for the NAND driver
6 * Copyright © 2004 Thomas Gleixner (tglx@linutronix.de)
8 * Description:
10 * When nand_scan_bbt is called, then it tries to find the bad block table
11 * depending on the options in the BBT descriptor(s). If no flash based BBT
12 * (NAND_BBT_USE_FLASH) is specified then the device is scanned for factory
13 * marked good / bad blocks. This information is used to create a memory BBT.
14 * Once a new bad block is discovered then the "factory" information is updated
15 * on the device.
16 * If a flash based BBT is specified then the function first tries to find the
17 * BBT on flash. If a BBT is found then the contents are read and the memory
18 * based BBT is created. If a mirrored BBT is selected then the mirror is
19 * searched too and the versions are compared. If the mirror has a greater
20 * version number, then the mirror BBT is used to build the memory based BBT.
21 * If the tables are not versioned, then we "or" the bad block information.
22 * If one of the BBTs is out of date or does not exist it is (re)created.
23 * If no BBT exists at all then the device is scanned for factory marked
24 * good / bad blocks and the bad block tables are created.
26 * For manufacturer created BBTs like the one found on M-SYS DOC devices
27 * the BBT is searched and read but never created
29 * The auto generated bad block table is located in the last good blocks
30 * of the device. The table is mirrored, so it can be updated eventually.
31 * The table is marked in the OOB area with an ident pattern and a version
32 * number which indicates which of both tables is more up to date. If the NAND
33 * controller needs the complete OOB area for the ECC information then the
34 * option NAND_BBT_NO_OOB should be used (along with NAND_BBT_USE_FLASH, of
35 * course): it moves the ident pattern and the version byte into the data area
36 * and the OOB area will remain untouched.
38 * The table uses 2 bits per block
39 * 11b: block is good
40 * 00b: block is factory marked bad
41 * 01b, 10b: block is marked bad due to wear
43 * The memory bad block table uses the following scheme:
44 * 00b: block is good
45 * 01b: block is marked bad due to wear
46 * 10b: block is reserved (to protect the bbt area)
47 * 11b: block is factory marked bad
49 * Multichip devices like DOC store the bad block info per floor.
51 * Following assumptions are made:
52 * - bbts start at a page boundary, if autolocated on a block boundary
53 * - the space necessary for a bbt in FLASH does not exceed a block boundary
56 #include <linux/slab.h>
57 #include <linux/types.h>
58 #include <linux/mtd/mtd.h>
59 #include <linux/mtd/bbm.h>
60 #include <linux/bitops.h>
61 #include <linux/delay.h>
62 #include <linux/vmalloc.h>
63 #include <linux/export.h>
64 #include <linux/string.h>
66 #include "internals.h"
68 #define BBT_BLOCK_GOOD 0x00
69 #define BBT_BLOCK_WORN 0x01
70 #define BBT_BLOCK_RESERVED 0x02
71 #define BBT_BLOCK_FACTORY_BAD 0x03
73 #define BBT_ENTRY_MASK 0x03
74 #define BBT_ENTRY_SHIFT 2
76 static inline uint8_t bbt_get_entry(struct nand_chip *chip, int block)
78 uint8_t entry = chip->bbt[block >> BBT_ENTRY_SHIFT];
79 entry >>= (block & BBT_ENTRY_MASK) * 2;
80 return entry & BBT_ENTRY_MASK;
83 static inline void bbt_mark_entry(struct nand_chip *chip, int block,
84 uint8_t mark)
86 uint8_t msk = (mark & BBT_ENTRY_MASK) << ((block & BBT_ENTRY_MASK) * 2);
87 chip->bbt[block >> BBT_ENTRY_SHIFT] |= msk;
90 static int check_pattern_no_oob(uint8_t *buf, struct nand_bbt_descr *td)
92 if (memcmp(buf, td->pattern, td->len))
93 return -1;
94 return 0;
97 /**
98 * check_pattern - [GENERIC] check if a pattern is in the buffer
99 * @buf: the buffer to search
100 * @len: the length of buffer to search
101 * @paglen: the pagelength
102 * @td: search pattern descriptor
104 * Check for a pattern at the given place. Used to search bad block tables and
105 * good / bad block identifiers.
107 static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td)
109 if (td->options & NAND_BBT_NO_OOB)
110 return check_pattern_no_oob(buf, td);
112 /* Compare the pattern */
113 if (memcmp(buf + paglen + td->offs, td->pattern, td->len))
114 return -1;
116 return 0;
120 * check_short_pattern - [GENERIC] check if a pattern is in the buffer
121 * @buf: the buffer to search
122 * @td: search pattern descriptor
124 * Check for a pattern at the given place. Used to search bad block tables and
125 * good / bad block identifiers. Same as check_pattern, but no optional empty
126 * check.
128 static int check_short_pattern(uint8_t *buf, struct nand_bbt_descr *td)
130 /* Compare the pattern */
131 if (memcmp(buf + td->offs, td->pattern, td->len))
132 return -1;
133 return 0;
137 * add_marker_len - compute the length of the marker in data area
138 * @td: BBT descriptor used for computation
140 * The length will be 0 if the marker is located in OOB area.
142 static u32 add_marker_len(struct nand_bbt_descr *td)
144 u32 len;
146 if (!(td->options & NAND_BBT_NO_OOB))
147 return 0;
149 len = td->len;
150 if (td->options & NAND_BBT_VERSION)
151 len++;
152 return len;
156 * read_bbt - [GENERIC] Read the bad block table starting from page
157 * @this: NAND chip object
158 * @buf: temporary buffer
159 * @page: the starting page
160 * @num: the number of bbt descriptors to read
161 * @td: the bbt describtion table
162 * @offs: block number offset in the table
164 * Read the bad block table starting from page.
166 static int read_bbt(struct nand_chip *this, uint8_t *buf, int page, int num,
167 struct nand_bbt_descr *td, int offs)
169 struct mtd_info *mtd = nand_to_mtd(this);
170 int res, ret = 0, i, j, act = 0;
171 size_t retlen, len, totlen;
172 loff_t from;
173 int bits = td->options & NAND_BBT_NRBITS_MSK;
174 uint8_t msk = (uint8_t)((1 << bits) - 1);
175 u32 marker_len;
176 int reserved_block_code = td->reserved_block_code;
178 totlen = (num * bits) >> 3;
179 marker_len = add_marker_len(td);
180 from = ((loff_t)page) << this->page_shift;
182 while (totlen) {
183 len = min(totlen, (size_t)(1 << this->bbt_erase_shift));
184 if (marker_len) {
186 * In case the BBT marker is not in the OOB area it
187 * will be just in the first page.
189 len -= marker_len;
190 from += marker_len;
191 marker_len = 0;
193 res = mtd_read(mtd, from, len, &retlen, buf);
194 if (res < 0) {
195 if (mtd_is_eccerr(res)) {
196 pr_info("nand_bbt: ECC error in BBT at 0x%012llx\n",
197 from & ~mtd->writesize);
198 return res;
199 } else if (mtd_is_bitflip(res)) {
200 pr_info("nand_bbt: corrected error in BBT at 0x%012llx\n",
201 from & ~mtd->writesize);
202 ret = res;
203 } else {
204 pr_info("nand_bbt: error reading BBT\n");
205 return res;
209 /* Analyse data */
210 for (i = 0; i < len; i++) {
211 uint8_t dat = buf[i];
212 for (j = 0; j < 8; j += bits, act++) {
213 uint8_t tmp = (dat >> j) & msk;
214 if (tmp == msk)
215 continue;
216 if (reserved_block_code && (tmp == reserved_block_code)) {
217 pr_info("nand_read_bbt: reserved block at 0x%012llx\n",
218 (loff_t)(offs + act) <<
219 this->bbt_erase_shift);
220 bbt_mark_entry(this, offs + act,
221 BBT_BLOCK_RESERVED);
222 mtd->ecc_stats.bbtblocks++;
223 continue;
226 * Leave it for now, if it's matured we can
227 * move this message to pr_debug.
229 pr_info("nand_read_bbt: bad block at 0x%012llx\n",
230 (loff_t)(offs + act) <<
231 this->bbt_erase_shift);
232 /* Factory marked bad or worn out? */
233 if (tmp == 0)
234 bbt_mark_entry(this, offs + act,
235 BBT_BLOCK_FACTORY_BAD);
236 else
237 bbt_mark_entry(this, offs + act,
238 BBT_BLOCK_WORN);
239 mtd->ecc_stats.badblocks++;
242 totlen -= len;
243 from += len;
245 return ret;
249 * read_abs_bbt - [GENERIC] Read the bad block table starting at a given page
250 * @this: NAND chip object
251 * @buf: temporary buffer
252 * @td: descriptor for the bad block table
253 * @chip: read the table for a specific chip, -1 read all chips; applies only if
254 * NAND_BBT_PERCHIP option is set
256 * Read the bad block table for all chips starting at a given page. We assume
257 * that the bbt bits are in consecutive order.
259 static int read_abs_bbt(struct nand_chip *this, uint8_t *buf,
260 struct nand_bbt_descr *td, int chip)
262 struct mtd_info *mtd = nand_to_mtd(this);
263 u64 targetsize = nanddev_target_size(&this->base);
264 int res = 0, i;
266 if (td->options & NAND_BBT_PERCHIP) {
267 int offs = 0;
268 for (i = 0; i < nanddev_ntargets(&this->base); i++) {
269 if (chip == -1 || chip == i)
270 res = read_bbt(this, buf, td->pages[i],
271 targetsize >> this->bbt_erase_shift,
272 td, offs);
273 if (res)
274 return res;
275 offs += targetsize >> this->bbt_erase_shift;
277 } else {
278 res = read_bbt(this, buf, td->pages[0],
279 mtd->size >> this->bbt_erase_shift, td, 0);
280 if (res)
281 return res;
283 return 0;
286 /* BBT marker is in the first page, no OOB */
287 static int scan_read_data(struct nand_chip *this, uint8_t *buf, loff_t offs,
288 struct nand_bbt_descr *td)
290 struct mtd_info *mtd = nand_to_mtd(this);
291 size_t retlen;
292 size_t len;
294 len = td->len;
295 if (td->options & NAND_BBT_VERSION)
296 len++;
298 return mtd_read(mtd, offs, len, &retlen, buf);
302 * scan_read_oob - [GENERIC] Scan data+OOB region to buffer
303 * @this: NAND chip object
304 * @buf: temporary buffer
305 * @offs: offset at which to scan
306 * @len: length of data region to read
308 * Scan read data from data+OOB. May traverse multiple pages, interleaving
309 * page,OOB,page,OOB,... in buf. Completes transfer and returns the "strongest"
310 * ECC condition (error or bitflip). May quit on the first (non-ECC) error.
312 static int scan_read_oob(struct nand_chip *this, uint8_t *buf, loff_t offs,
313 size_t len)
315 struct mtd_info *mtd = nand_to_mtd(this);
316 struct mtd_oob_ops ops;
317 int res, ret = 0;
319 ops.mode = MTD_OPS_PLACE_OOB;
320 ops.ooboffs = 0;
321 ops.ooblen = mtd->oobsize;
323 while (len > 0) {
324 ops.datbuf = buf;
325 ops.len = min(len, (size_t)mtd->writesize);
326 ops.oobbuf = buf + ops.len;
328 res = mtd_read_oob(mtd, offs, &ops);
329 if (res) {
330 if (!mtd_is_bitflip_or_eccerr(res))
331 return res;
332 else if (mtd_is_eccerr(res) || !ret)
333 ret = res;
336 buf += mtd->oobsize + mtd->writesize;
337 len -= mtd->writesize;
338 offs += mtd->writesize;
340 return ret;
343 static int scan_read(struct nand_chip *this, uint8_t *buf, loff_t offs,
344 size_t len, struct nand_bbt_descr *td)
346 if (td->options & NAND_BBT_NO_OOB)
347 return scan_read_data(this, buf, offs, td);
348 else
349 return scan_read_oob(this, buf, offs, len);
352 /* Scan write data with oob to flash */
353 static int scan_write_bbt(struct nand_chip *this, loff_t offs, size_t len,
354 uint8_t *buf, uint8_t *oob)
356 struct mtd_info *mtd = nand_to_mtd(this);
357 struct mtd_oob_ops ops;
359 ops.mode = MTD_OPS_PLACE_OOB;
360 ops.ooboffs = 0;
361 ops.ooblen = mtd->oobsize;
362 ops.datbuf = buf;
363 ops.oobbuf = oob;
364 ops.len = len;
366 return mtd_write_oob(mtd, offs, &ops);
369 static u32 bbt_get_ver_offs(struct nand_chip *this, struct nand_bbt_descr *td)
371 struct mtd_info *mtd = nand_to_mtd(this);
372 u32 ver_offs = td->veroffs;
374 if (!(td->options & NAND_BBT_NO_OOB))
375 ver_offs += mtd->writesize;
376 return ver_offs;
380 * read_abs_bbts - [GENERIC] Read the bad block table(s) for all chips starting at a given page
381 * @this: NAND chip object
382 * @buf: temporary buffer
383 * @td: descriptor for the bad block table
384 * @md: descriptor for the bad block table mirror
386 * Read the bad block table(s) for all chips starting at a given page. We
387 * assume that the bbt bits are in consecutive order.
389 static void read_abs_bbts(struct nand_chip *this, uint8_t *buf,
390 struct nand_bbt_descr *td, struct nand_bbt_descr *md)
392 struct mtd_info *mtd = nand_to_mtd(this);
394 /* Read the primary version, if available */
395 if (td->options & NAND_BBT_VERSION) {
396 scan_read(this, buf, (loff_t)td->pages[0] << this->page_shift,
397 mtd->writesize, td);
398 td->version[0] = buf[bbt_get_ver_offs(this, td)];
399 pr_info("Bad block table at page %d, version 0x%02X\n",
400 td->pages[0], td->version[0]);
403 /* Read the mirror version, if available */
404 if (md && (md->options & NAND_BBT_VERSION)) {
405 scan_read(this, buf, (loff_t)md->pages[0] << this->page_shift,
406 mtd->writesize, md);
407 md->version[0] = buf[bbt_get_ver_offs(this, md)];
408 pr_info("Bad block table at page %d, version 0x%02X\n",
409 md->pages[0], md->version[0]);
413 /* Scan a given block partially */
414 static int scan_block_fast(struct nand_chip *this, struct nand_bbt_descr *bd,
415 loff_t offs, uint8_t *buf)
417 struct mtd_info *mtd = nand_to_mtd(this);
419 struct mtd_oob_ops ops;
420 int ret, page_offset;
422 ops.ooblen = mtd->oobsize;
423 ops.oobbuf = buf;
424 ops.ooboffs = 0;
425 ops.datbuf = NULL;
426 ops.mode = MTD_OPS_PLACE_OOB;
428 page_offset = nand_bbm_get_next_page(this, 0);
430 while (page_offset >= 0) {
432 * Read the full oob until read_oob is fixed to handle single
433 * byte reads for 16 bit buswidth.
435 ret = mtd_read_oob(mtd, offs + (page_offset * mtd->writesize),
436 &ops);
437 /* Ignore ECC errors when checking for BBM */
438 if (ret && !mtd_is_bitflip_or_eccerr(ret))
439 return ret;
441 if (check_short_pattern(buf, bd))
442 return 1;
444 page_offset = nand_bbm_get_next_page(this, page_offset + 1);
447 return 0;
451 * create_bbt - [GENERIC] Create a bad block table by scanning the device
452 * @this: NAND chip object
453 * @buf: temporary buffer
454 * @bd: descriptor for the good/bad block search pattern
455 * @chip: create the table for a specific chip, -1 read all chips; applies only
456 * if NAND_BBT_PERCHIP option is set
458 * Create a bad block table by scanning the device for the given good/bad block
459 * identify pattern.
461 static int create_bbt(struct nand_chip *this, uint8_t *buf,
462 struct nand_bbt_descr *bd, int chip)
464 u64 targetsize = nanddev_target_size(&this->base);
465 struct mtd_info *mtd = nand_to_mtd(this);
466 int i, numblocks, startblock;
467 loff_t from;
469 pr_info("Scanning device for bad blocks\n");
471 if (chip == -1) {
472 numblocks = mtd->size >> this->bbt_erase_shift;
473 startblock = 0;
474 from = 0;
475 } else {
476 if (chip >= nanddev_ntargets(&this->base)) {
477 pr_warn("create_bbt(): chipnr (%d) > available chips (%d)\n",
478 chip + 1, nanddev_ntargets(&this->base));
479 return -EINVAL;
481 numblocks = targetsize >> this->bbt_erase_shift;
482 startblock = chip * numblocks;
483 numblocks += startblock;
484 from = (loff_t)startblock << this->bbt_erase_shift;
487 for (i = startblock; i < numblocks; i++) {
488 int ret;
490 BUG_ON(bd->options & NAND_BBT_NO_OOB);
492 ret = scan_block_fast(this, bd, from, buf);
493 if (ret < 0)
494 return ret;
496 if (ret) {
497 bbt_mark_entry(this, i, BBT_BLOCK_FACTORY_BAD);
498 pr_warn("Bad eraseblock %d at 0x%012llx\n",
499 i, (unsigned long long)from);
500 mtd->ecc_stats.badblocks++;
503 from += (1 << this->bbt_erase_shift);
505 return 0;
509 * search_bbt - [GENERIC] scan the device for a specific bad block table
510 * @this: NAND chip object
511 * @buf: temporary buffer
512 * @td: descriptor for the bad block table
514 * Read the bad block table by searching for a given ident pattern. Search is
515 * preformed either from the beginning up or from the end of the device
516 * downwards. The search starts always at the start of a block. If the option
517 * NAND_BBT_PERCHIP is given, each chip is searched for a bbt, which contains
518 * the bad block information of this chip. This is necessary to provide support
519 * for certain DOC devices.
521 * The bbt ident pattern resides in the oob area of the first page in a block.
523 static int search_bbt(struct nand_chip *this, uint8_t *buf,
524 struct nand_bbt_descr *td)
526 u64 targetsize = nanddev_target_size(&this->base);
527 struct mtd_info *mtd = nand_to_mtd(this);
528 int i, chips;
529 int startblock, block, dir;
530 int scanlen = mtd->writesize + mtd->oobsize;
531 int bbtblocks;
532 int blocktopage = this->bbt_erase_shift - this->page_shift;
534 /* Search direction top -> down? */
535 if (td->options & NAND_BBT_LASTBLOCK) {
536 startblock = (mtd->size >> this->bbt_erase_shift) - 1;
537 dir = -1;
538 } else {
539 startblock = 0;
540 dir = 1;
543 /* Do we have a bbt per chip? */
544 if (td->options & NAND_BBT_PERCHIP) {
545 chips = nanddev_ntargets(&this->base);
546 bbtblocks = targetsize >> this->bbt_erase_shift;
547 startblock &= bbtblocks - 1;
548 } else {
549 chips = 1;
550 bbtblocks = mtd->size >> this->bbt_erase_shift;
553 for (i = 0; i < chips; i++) {
554 /* Reset version information */
555 td->version[i] = 0;
556 td->pages[i] = -1;
557 /* Scan the maximum number of blocks */
558 for (block = 0; block < td->maxblocks; block++) {
560 int actblock = startblock + dir * block;
561 loff_t offs = (loff_t)actblock << this->bbt_erase_shift;
563 /* Read first page */
564 scan_read(this, buf, offs, mtd->writesize, td);
565 if (!check_pattern(buf, scanlen, mtd->writesize, td)) {
566 td->pages[i] = actblock << blocktopage;
567 if (td->options & NAND_BBT_VERSION) {
568 offs = bbt_get_ver_offs(this, td);
569 td->version[i] = buf[offs];
571 break;
574 startblock += targetsize >> this->bbt_erase_shift;
576 /* Check, if we found a bbt for each requested chip */
577 for (i = 0; i < chips; i++) {
578 if (td->pages[i] == -1)
579 pr_warn("Bad block table not found for chip %d\n", i);
580 else
581 pr_info("Bad block table found at page %d, version 0x%02X\n",
582 td->pages[i], td->version[i]);
584 return 0;
588 * search_read_bbts - [GENERIC] scan the device for bad block table(s)
589 * @this: NAND chip object
590 * @buf: temporary buffer
591 * @td: descriptor for the bad block table
592 * @md: descriptor for the bad block table mirror
594 * Search and read the bad block table(s).
596 static void search_read_bbts(struct nand_chip *this, uint8_t *buf,
597 struct nand_bbt_descr *td,
598 struct nand_bbt_descr *md)
600 /* Search the primary table */
601 search_bbt(this, buf, td);
603 /* Search the mirror table */
604 if (md)
605 search_bbt(this, buf, md);
609 * get_bbt_block - Get the first valid eraseblock suitable to store a BBT
610 * @this: the NAND device
611 * @td: the BBT description
612 * @md: the mirror BBT descriptor
613 * @chip: the CHIP selector
615 * This functions returns a positive block number pointing a valid eraseblock
616 * suitable to store a BBT (i.e. in the range reserved for BBT), or -ENOSPC if
617 * all blocks are already used of marked bad. If td->pages[chip] was already
618 * pointing to a valid block we re-use it, otherwise we search for the next
619 * valid one.
621 static int get_bbt_block(struct nand_chip *this, struct nand_bbt_descr *td,
622 struct nand_bbt_descr *md, int chip)
624 u64 targetsize = nanddev_target_size(&this->base);
625 int startblock, dir, page, numblocks, i;
628 * There was already a version of the table, reuse the page. This
629 * applies for absolute placement too, as we have the page number in
630 * td->pages.
632 if (td->pages[chip] != -1)
633 return td->pages[chip] >>
634 (this->bbt_erase_shift - this->page_shift);
636 numblocks = (int)(targetsize >> this->bbt_erase_shift);
637 if (!(td->options & NAND_BBT_PERCHIP))
638 numblocks *= nanddev_ntargets(&this->base);
641 * Automatic placement of the bad block table. Search direction
642 * top -> down?
644 if (td->options & NAND_BBT_LASTBLOCK) {
645 startblock = numblocks * (chip + 1) - 1;
646 dir = -1;
647 } else {
648 startblock = chip * numblocks;
649 dir = 1;
652 for (i = 0; i < td->maxblocks; i++) {
653 int block = startblock + dir * i;
655 /* Check, if the block is bad */
656 switch (bbt_get_entry(this, block)) {
657 case BBT_BLOCK_WORN:
658 case BBT_BLOCK_FACTORY_BAD:
659 continue;
662 page = block << (this->bbt_erase_shift - this->page_shift);
664 /* Check, if the block is used by the mirror table */
665 if (!md || md->pages[chip] != page)
666 return block;
669 return -ENOSPC;
673 * mark_bbt_block_bad - Mark one of the block reserved for BBT bad
674 * @this: the NAND device
675 * @td: the BBT description
676 * @chip: the CHIP selector
677 * @block: the BBT block to mark
679 * Blocks reserved for BBT can become bad. This functions is an helper to mark
680 * such blocks as bad. It takes care of updating the in-memory BBT, marking the
681 * block as bad using a bad block marker and invalidating the associated
682 * td->pages[] entry.
684 static void mark_bbt_block_bad(struct nand_chip *this,
685 struct nand_bbt_descr *td,
686 int chip, int block)
688 loff_t to;
689 int res;
691 bbt_mark_entry(this, block, BBT_BLOCK_WORN);
693 to = (loff_t)block << this->bbt_erase_shift;
694 res = nand_markbad_bbm(this, to);
695 if (res)
696 pr_warn("nand_bbt: error %d while marking block %d bad\n",
697 res, block);
699 td->pages[chip] = -1;
703 * write_bbt - [GENERIC] (Re)write the bad block table
704 * @this: NAND chip object
705 * @buf: temporary buffer
706 * @td: descriptor for the bad block table
707 * @md: descriptor for the bad block table mirror
708 * @chipsel: selector for a specific chip, -1 for all
710 * (Re)write the bad block table.
712 static int write_bbt(struct nand_chip *this, uint8_t *buf,
713 struct nand_bbt_descr *td, struct nand_bbt_descr *md,
714 int chipsel)
716 u64 targetsize = nanddev_target_size(&this->base);
717 struct mtd_info *mtd = nand_to_mtd(this);
718 struct erase_info einfo;
719 int i, res, chip = 0;
720 int bits, page, offs, numblocks, sft, sftmsk;
721 int nrchips, pageoffs, ooboffs;
722 uint8_t msk[4];
723 uint8_t rcode = td->reserved_block_code;
724 size_t retlen, len = 0;
725 loff_t to;
726 struct mtd_oob_ops ops;
728 ops.ooblen = mtd->oobsize;
729 ops.ooboffs = 0;
730 ops.datbuf = NULL;
731 ops.mode = MTD_OPS_PLACE_OOB;
733 if (!rcode)
734 rcode = 0xff;
735 /* Write bad block table per chip rather than per device? */
736 if (td->options & NAND_BBT_PERCHIP) {
737 numblocks = (int)(targetsize >> this->bbt_erase_shift);
738 /* Full device write or specific chip? */
739 if (chipsel == -1) {
740 nrchips = nanddev_ntargets(&this->base);
741 } else {
742 nrchips = chipsel + 1;
743 chip = chipsel;
745 } else {
746 numblocks = (int)(mtd->size >> this->bbt_erase_shift);
747 nrchips = 1;
750 /* Loop through the chips */
751 while (chip < nrchips) {
752 int block;
754 block = get_bbt_block(this, td, md, chip);
755 if (block < 0) {
756 pr_err("No space left to write bad block table\n");
757 res = block;
758 goto outerr;
762 * get_bbt_block() returns a block number, shift the value to
763 * get a page number.
765 page = block << (this->bbt_erase_shift - this->page_shift);
767 /* Set up shift count and masks for the flash table */
768 bits = td->options & NAND_BBT_NRBITS_MSK;
769 msk[2] = ~rcode;
770 switch (bits) {
771 case 1: sft = 3; sftmsk = 0x07; msk[0] = 0x00; msk[1] = 0x01;
772 msk[3] = 0x01;
773 break;
774 case 2: sft = 2; sftmsk = 0x06; msk[0] = 0x00; msk[1] = 0x01;
775 msk[3] = 0x03;
776 break;
777 case 4: sft = 1; sftmsk = 0x04; msk[0] = 0x00; msk[1] = 0x0C;
778 msk[3] = 0x0f;
779 break;
780 case 8: sft = 0; sftmsk = 0x00; msk[0] = 0x00; msk[1] = 0x0F;
781 msk[3] = 0xff;
782 break;
783 default: return -EINVAL;
786 to = ((loff_t)page) << this->page_shift;
788 /* Must we save the block contents? */
789 if (td->options & NAND_BBT_SAVECONTENT) {
790 /* Make it block aligned */
791 to &= ~(((loff_t)1 << this->bbt_erase_shift) - 1);
792 len = 1 << this->bbt_erase_shift;
793 res = mtd_read(mtd, to, len, &retlen, buf);
794 if (res < 0) {
795 if (retlen != len) {
796 pr_info("nand_bbt: error reading block for writing the bad block table\n");
797 return res;
799 pr_warn("nand_bbt: ECC error while reading block for writing bad block table\n");
801 /* Read oob data */
802 ops.ooblen = (len >> this->page_shift) * mtd->oobsize;
803 ops.oobbuf = &buf[len];
804 res = mtd_read_oob(mtd, to + mtd->writesize, &ops);
805 if (res < 0 || ops.oobretlen != ops.ooblen)
806 goto outerr;
808 /* Calc the byte offset in the buffer */
809 pageoffs = page - (int)(to >> this->page_shift);
810 offs = pageoffs << this->page_shift;
811 /* Preset the bbt area with 0xff */
812 memset(&buf[offs], 0xff, (size_t)(numblocks >> sft));
813 ooboffs = len + (pageoffs * mtd->oobsize);
815 } else if (td->options & NAND_BBT_NO_OOB) {
816 ooboffs = 0;
817 offs = td->len;
818 /* The version byte */
819 if (td->options & NAND_BBT_VERSION)
820 offs++;
821 /* Calc length */
822 len = (size_t)(numblocks >> sft);
823 len += offs;
824 /* Make it page aligned! */
825 len = ALIGN(len, mtd->writesize);
826 /* Preset the buffer with 0xff */
827 memset(buf, 0xff, len);
828 /* Pattern is located at the begin of first page */
829 memcpy(buf, td->pattern, td->len);
830 } else {
831 /* Calc length */
832 len = (size_t)(numblocks >> sft);
833 /* Make it page aligned! */
834 len = ALIGN(len, mtd->writesize);
835 /* Preset the buffer with 0xff */
836 memset(buf, 0xff, len +
837 (len >> this->page_shift)* mtd->oobsize);
838 offs = 0;
839 ooboffs = len;
840 /* Pattern is located in oob area of first page */
841 memcpy(&buf[ooboffs + td->offs], td->pattern, td->len);
844 if (td->options & NAND_BBT_VERSION)
845 buf[ooboffs + td->veroffs] = td->version[chip];
847 /* Walk through the memory table */
848 for (i = 0; i < numblocks; i++) {
849 uint8_t dat;
850 int sftcnt = (i << (3 - sft)) & sftmsk;
851 dat = bbt_get_entry(this, chip * numblocks + i);
852 /* Do not store the reserved bbt blocks! */
853 buf[offs + (i >> sft)] &= ~(msk[dat] << sftcnt);
856 memset(&einfo, 0, sizeof(einfo));
857 einfo.addr = to;
858 einfo.len = 1 << this->bbt_erase_shift;
859 res = nand_erase_nand(this, &einfo, 1);
860 if (res < 0) {
861 pr_warn("nand_bbt: error while erasing BBT block %d\n",
862 res);
863 mark_bbt_block_bad(this, td, chip, block);
864 continue;
867 res = scan_write_bbt(this, to, len, buf,
868 td->options & NAND_BBT_NO_OOB ?
869 NULL : &buf[len]);
870 if (res < 0) {
871 pr_warn("nand_bbt: error while writing BBT block %d\n",
872 res);
873 mark_bbt_block_bad(this, td, chip, block);
874 continue;
877 pr_info("Bad block table written to 0x%012llx, version 0x%02X\n",
878 (unsigned long long)to, td->version[chip]);
880 /* Mark it as used */
881 td->pages[chip++] = page;
883 return 0;
885 outerr:
886 pr_warn("nand_bbt: error while writing bad block table %d\n", res);
887 return res;
891 * nand_memory_bbt - [GENERIC] create a memory based bad block table
892 * @this: NAND chip object
893 * @bd: descriptor for the good/bad block search pattern
895 * The function creates a memory based bbt by scanning the device for
896 * manufacturer / software marked good / bad blocks.
898 static inline int nand_memory_bbt(struct nand_chip *this,
899 struct nand_bbt_descr *bd)
901 u8 *pagebuf = nand_get_data_buf(this);
903 return create_bbt(this, pagebuf, bd, -1);
907 * check_create - [GENERIC] create and write bbt(s) if necessary
908 * @this: the NAND device
909 * @buf: temporary buffer
910 * @bd: descriptor for the good/bad block search pattern
912 * The function checks the results of the previous call to read_bbt and creates
913 * / updates the bbt(s) if necessary. Creation is necessary if no bbt was found
914 * for the chip/device. Update is necessary if one of the tables is missing or
915 * the version nr. of one table is less than the other.
917 static int check_create(struct nand_chip *this, uint8_t *buf,
918 struct nand_bbt_descr *bd)
920 int i, chips, writeops, create, chipsel, res, res2;
921 struct nand_bbt_descr *td = this->bbt_td;
922 struct nand_bbt_descr *md = this->bbt_md;
923 struct nand_bbt_descr *rd, *rd2;
925 /* Do we have a bbt per chip? */
926 if (td->options & NAND_BBT_PERCHIP)
927 chips = nanddev_ntargets(&this->base);
928 else
929 chips = 1;
931 for (i = 0; i < chips; i++) {
932 writeops = 0;
933 create = 0;
934 rd = NULL;
935 rd2 = NULL;
936 res = res2 = 0;
937 /* Per chip or per device? */
938 chipsel = (td->options & NAND_BBT_PERCHIP) ? i : -1;
939 /* Mirrored table available? */
940 if (md) {
941 if (td->pages[i] == -1 && md->pages[i] == -1) {
942 create = 1;
943 writeops = 0x03;
944 } else if (td->pages[i] == -1) {
945 rd = md;
946 writeops = 0x01;
947 } else if (md->pages[i] == -1) {
948 rd = td;
949 writeops = 0x02;
950 } else if (td->version[i] == md->version[i]) {
951 rd = td;
952 if (!(td->options & NAND_BBT_VERSION))
953 rd2 = md;
954 } else if (((int8_t)(td->version[i] - md->version[i])) > 0) {
955 rd = td;
956 writeops = 0x02;
957 } else {
958 rd = md;
959 writeops = 0x01;
961 } else {
962 if (td->pages[i] == -1) {
963 create = 1;
964 writeops = 0x01;
965 } else {
966 rd = td;
970 if (create) {
971 /* Create the bad block table by scanning the device? */
972 if (!(td->options & NAND_BBT_CREATE))
973 continue;
975 /* Create the table in memory by scanning the chip(s) */
976 if (!(this->bbt_options & NAND_BBT_CREATE_EMPTY))
977 create_bbt(this, buf, bd, chipsel);
979 td->version[i] = 1;
980 if (md)
981 md->version[i] = 1;
984 /* Read back first? */
985 if (rd) {
986 res = read_abs_bbt(this, buf, rd, chipsel);
987 if (mtd_is_eccerr(res)) {
988 /* Mark table as invalid */
989 rd->pages[i] = -1;
990 rd->version[i] = 0;
991 i--;
992 continue;
995 /* If they weren't versioned, read both */
996 if (rd2) {
997 res2 = read_abs_bbt(this, buf, rd2, chipsel);
998 if (mtd_is_eccerr(res2)) {
999 /* Mark table as invalid */
1000 rd2->pages[i] = -1;
1001 rd2->version[i] = 0;
1002 i--;
1003 continue;
1007 /* Scrub the flash table(s)? */
1008 if (mtd_is_bitflip(res) || mtd_is_bitflip(res2))
1009 writeops = 0x03;
1011 /* Update version numbers before writing */
1012 if (md) {
1013 td->version[i] = max(td->version[i], md->version[i]);
1014 md->version[i] = td->version[i];
1017 /* Write the bad block table to the device? */
1018 if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) {
1019 res = write_bbt(this, buf, td, md, chipsel);
1020 if (res < 0)
1021 return res;
1024 /* Write the mirror bad block table to the device? */
1025 if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) {
1026 res = write_bbt(this, buf, md, td, chipsel);
1027 if (res < 0)
1028 return res;
1031 return 0;
1035 * nand_update_bbt - update bad block table(s)
1036 * @this: the NAND device
1037 * @offs: the offset of the newly marked block
1039 * The function updates the bad block table(s).
1041 static int nand_update_bbt(struct nand_chip *this, loff_t offs)
1043 struct mtd_info *mtd = nand_to_mtd(this);
1044 int len, res = 0;
1045 int chip, chipsel;
1046 uint8_t *buf;
1047 struct nand_bbt_descr *td = this->bbt_td;
1048 struct nand_bbt_descr *md = this->bbt_md;
1050 if (!this->bbt || !td)
1051 return -EINVAL;
1053 /* Allocate a temporary buffer for one eraseblock incl. oob */
1054 len = (1 << this->bbt_erase_shift);
1055 len += (len >> this->page_shift) * mtd->oobsize;
1056 buf = kmalloc(len, GFP_KERNEL);
1057 if (!buf)
1058 return -ENOMEM;
1060 /* Do we have a bbt per chip? */
1061 if (td->options & NAND_BBT_PERCHIP) {
1062 chip = (int)(offs >> this->chip_shift);
1063 chipsel = chip;
1064 } else {
1065 chip = 0;
1066 chipsel = -1;
1069 td->version[chip]++;
1070 if (md)
1071 md->version[chip]++;
1073 /* Write the bad block table to the device? */
1074 if (td->options & NAND_BBT_WRITE) {
1075 res = write_bbt(this, buf, td, md, chipsel);
1076 if (res < 0)
1077 goto out;
1079 /* Write the mirror bad block table to the device? */
1080 if (md && (md->options & NAND_BBT_WRITE)) {
1081 res = write_bbt(this, buf, md, td, chipsel);
1084 out:
1085 kfree(buf);
1086 return res;
1090 * mark_bbt_region - [GENERIC] mark the bad block table regions
1091 * @this: the NAND device
1092 * @td: bad block table descriptor
1094 * The bad block table regions are marked as "bad" to prevent accidental
1095 * erasures / writes. The regions are identified by the mark 0x02.
1097 static void mark_bbt_region(struct nand_chip *this, struct nand_bbt_descr *td)
1099 u64 targetsize = nanddev_target_size(&this->base);
1100 struct mtd_info *mtd = nand_to_mtd(this);
1101 int i, j, chips, block, nrblocks, update;
1102 uint8_t oldval;
1104 /* Do we have a bbt per chip? */
1105 if (td->options & NAND_BBT_PERCHIP) {
1106 chips = nanddev_ntargets(&this->base);
1107 nrblocks = (int)(targetsize >> this->bbt_erase_shift);
1108 } else {
1109 chips = 1;
1110 nrblocks = (int)(mtd->size >> this->bbt_erase_shift);
1113 for (i = 0; i < chips; i++) {
1114 if ((td->options & NAND_BBT_ABSPAGE) ||
1115 !(td->options & NAND_BBT_WRITE)) {
1116 if (td->pages[i] == -1)
1117 continue;
1118 block = td->pages[i] >> (this->bbt_erase_shift - this->page_shift);
1119 oldval = bbt_get_entry(this, block);
1120 bbt_mark_entry(this, block, BBT_BLOCK_RESERVED);
1121 if ((oldval != BBT_BLOCK_RESERVED) &&
1122 td->reserved_block_code)
1123 nand_update_bbt(this, (loff_t)block <<
1124 this->bbt_erase_shift);
1125 continue;
1127 update = 0;
1128 if (td->options & NAND_BBT_LASTBLOCK)
1129 block = ((i + 1) * nrblocks) - td->maxblocks;
1130 else
1131 block = i * nrblocks;
1132 for (j = 0; j < td->maxblocks; j++) {
1133 oldval = bbt_get_entry(this, block);
1134 bbt_mark_entry(this, block, BBT_BLOCK_RESERVED);
1135 if (oldval != BBT_BLOCK_RESERVED)
1136 update = 1;
1137 block++;
1140 * If we want reserved blocks to be recorded to flash, and some
1141 * new ones have been marked, then we need to update the stored
1142 * bbts. This should only happen once.
1144 if (update && td->reserved_block_code)
1145 nand_update_bbt(this, (loff_t)(block - 1) <<
1146 this->bbt_erase_shift);
1151 * verify_bbt_descr - verify the bad block description
1152 * @this: the NAND device
1153 * @bd: the table to verify
1155 * This functions performs a few sanity checks on the bad block description
1156 * table.
1158 static void verify_bbt_descr(struct nand_chip *this, struct nand_bbt_descr *bd)
1160 u64 targetsize = nanddev_target_size(&this->base);
1161 struct mtd_info *mtd = nand_to_mtd(this);
1162 u32 pattern_len;
1163 u32 bits;
1164 u32 table_size;
1166 if (!bd)
1167 return;
1169 pattern_len = bd->len;
1170 bits = bd->options & NAND_BBT_NRBITS_MSK;
1172 BUG_ON((this->bbt_options & NAND_BBT_NO_OOB) &&
1173 !(this->bbt_options & NAND_BBT_USE_FLASH));
1174 BUG_ON(!bits);
1176 if (bd->options & NAND_BBT_VERSION)
1177 pattern_len++;
1179 if (bd->options & NAND_BBT_NO_OOB) {
1180 BUG_ON(!(this->bbt_options & NAND_BBT_USE_FLASH));
1181 BUG_ON(!(this->bbt_options & NAND_BBT_NO_OOB));
1182 BUG_ON(bd->offs);
1183 if (bd->options & NAND_BBT_VERSION)
1184 BUG_ON(bd->veroffs != bd->len);
1185 BUG_ON(bd->options & NAND_BBT_SAVECONTENT);
1188 if (bd->options & NAND_BBT_PERCHIP)
1189 table_size = targetsize >> this->bbt_erase_shift;
1190 else
1191 table_size = mtd->size >> this->bbt_erase_shift;
1192 table_size >>= 3;
1193 table_size *= bits;
1194 if (bd->options & NAND_BBT_NO_OOB)
1195 table_size += pattern_len;
1196 BUG_ON(table_size > (1 << this->bbt_erase_shift));
1200 * nand_scan_bbt - [NAND Interface] scan, find, read and maybe create bad block table(s)
1201 * @this: the NAND device
1202 * @bd: descriptor for the good/bad block search pattern
1204 * The function checks, if a bad block table(s) is/are already available. If
1205 * not it scans the device for manufacturer marked good / bad blocks and writes
1206 * the bad block table(s) to the selected place.
1208 * The bad block table memory is allocated here. It must be freed by calling
1209 * the nand_free_bbt function.
1211 static int nand_scan_bbt(struct nand_chip *this, struct nand_bbt_descr *bd)
1213 struct mtd_info *mtd = nand_to_mtd(this);
1214 int len, res;
1215 uint8_t *buf;
1216 struct nand_bbt_descr *td = this->bbt_td;
1217 struct nand_bbt_descr *md = this->bbt_md;
1219 len = (mtd->size >> (this->bbt_erase_shift + 2)) ? : 1;
1221 * Allocate memory (2bit per block) and clear the memory bad block
1222 * table.
1224 this->bbt = kzalloc(len, GFP_KERNEL);
1225 if (!this->bbt)
1226 return -ENOMEM;
1229 * If no primary table descriptor is given, scan the device to build a
1230 * memory based bad block table.
1232 if (!td) {
1233 if ((res = nand_memory_bbt(this, bd))) {
1234 pr_err("nand_bbt: can't scan flash and build the RAM-based BBT\n");
1235 goto err_free_bbt;
1237 return 0;
1239 verify_bbt_descr(this, td);
1240 verify_bbt_descr(this, md);
1242 /* Allocate a temporary buffer for one eraseblock incl. oob */
1243 len = (1 << this->bbt_erase_shift);
1244 len += (len >> this->page_shift) * mtd->oobsize;
1245 buf = vmalloc(len);
1246 if (!buf) {
1247 res = -ENOMEM;
1248 goto err_free_bbt;
1251 /* Is the bbt at a given page? */
1252 if (td->options & NAND_BBT_ABSPAGE) {
1253 read_abs_bbts(this, buf, td, md);
1254 } else {
1255 /* Search the bad block table using a pattern in oob */
1256 search_read_bbts(this, buf, td, md);
1259 res = check_create(this, buf, bd);
1260 if (res)
1261 goto err_free_buf;
1263 /* Prevent the bbt regions from erasing / writing */
1264 mark_bbt_region(this, td);
1265 if (md)
1266 mark_bbt_region(this, md);
1268 vfree(buf);
1269 return 0;
1271 err_free_buf:
1272 vfree(buf);
1273 err_free_bbt:
1274 kfree(this->bbt);
1275 this->bbt = NULL;
1276 return res;
1280 * Define some generic bad / good block scan pattern which are used
1281 * while scanning a device for factory marked good / bad blocks.
1283 static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
1285 /* Generic flash bbt descriptors */
1286 static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' };
1287 static uint8_t mirror_pattern[] = {'1', 't', 'b', 'B' };
1289 static struct nand_bbt_descr bbt_main_descr = {
1290 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
1291 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
1292 .offs = 8,
1293 .len = 4,
1294 .veroffs = 12,
1295 .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
1296 .pattern = bbt_pattern
1299 static struct nand_bbt_descr bbt_mirror_descr = {
1300 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
1301 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
1302 .offs = 8,
1303 .len = 4,
1304 .veroffs = 12,
1305 .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
1306 .pattern = mirror_pattern
1309 static struct nand_bbt_descr bbt_main_no_oob_descr = {
1310 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
1311 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP
1312 | NAND_BBT_NO_OOB,
1313 .len = 4,
1314 .veroffs = 4,
1315 .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
1316 .pattern = bbt_pattern
1319 static struct nand_bbt_descr bbt_mirror_no_oob_descr = {
1320 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
1321 | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP
1322 | NAND_BBT_NO_OOB,
1323 .len = 4,
1324 .veroffs = 4,
1325 .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
1326 .pattern = mirror_pattern
1329 #define BADBLOCK_SCAN_MASK (~NAND_BBT_NO_OOB)
1331 * nand_create_badblock_pattern - [INTERN] Creates a BBT descriptor structure
1332 * @this: NAND chip to create descriptor for
1334 * This function allocates and initializes a nand_bbt_descr for BBM detection
1335 * based on the properties of @this. The new descriptor is stored in
1336 * this->badblock_pattern. Thus, this->badblock_pattern should be NULL when
1337 * passed to this function.
1339 static int nand_create_badblock_pattern(struct nand_chip *this)
1341 struct nand_bbt_descr *bd;
1342 if (this->badblock_pattern) {
1343 pr_warn("Bad block pattern already allocated; not replacing\n");
1344 return -EINVAL;
1346 bd = kzalloc(sizeof(*bd), GFP_KERNEL);
1347 if (!bd)
1348 return -ENOMEM;
1349 bd->options = this->bbt_options & BADBLOCK_SCAN_MASK;
1350 bd->offs = this->badblockpos;
1351 bd->len = (this->options & NAND_BUSWIDTH_16) ? 2 : 1;
1352 bd->pattern = scan_ff_pattern;
1353 bd->options |= NAND_BBT_DYNAMICSTRUCT;
1354 this->badblock_pattern = bd;
1355 return 0;
1359 * nand_create_bbt - [NAND Interface] Select a default bad block table for the device
1360 * @this: NAND chip object
1362 * This function selects the default bad block table support for the device and
1363 * calls the nand_scan_bbt function.
1365 int nand_create_bbt(struct nand_chip *this)
1367 int ret;
1369 /* Is a flash based bad block table requested? */
1370 if (this->bbt_options & NAND_BBT_USE_FLASH) {
1371 /* Use the default pattern descriptors */
1372 if (!this->bbt_td) {
1373 if (this->bbt_options & NAND_BBT_NO_OOB) {
1374 this->bbt_td = &bbt_main_no_oob_descr;
1375 this->bbt_md = &bbt_mirror_no_oob_descr;
1376 } else {
1377 this->bbt_td = &bbt_main_descr;
1378 this->bbt_md = &bbt_mirror_descr;
1381 } else {
1382 this->bbt_td = NULL;
1383 this->bbt_md = NULL;
1386 if (!this->badblock_pattern) {
1387 ret = nand_create_badblock_pattern(this);
1388 if (ret)
1389 return ret;
1392 return nand_scan_bbt(this, this->badblock_pattern);
1394 EXPORT_SYMBOL(nand_create_bbt);
1397 * nand_isreserved_bbt - [NAND Interface] Check if a block is reserved
1398 * @this: NAND chip object
1399 * @offs: offset in the device
1401 int nand_isreserved_bbt(struct nand_chip *this, loff_t offs)
1403 int block;
1405 block = (int)(offs >> this->bbt_erase_shift);
1406 return bbt_get_entry(this, block) == BBT_BLOCK_RESERVED;
1410 * nand_isbad_bbt - [NAND Interface] Check if a block is bad
1411 * @this: NAND chip object
1412 * @offs: offset in the device
1413 * @allowbbt: allow access to bad block table region
1415 int nand_isbad_bbt(struct nand_chip *this, loff_t offs, int allowbbt)
1417 int block, res;
1419 block = (int)(offs >> this->bbt_erase_shift);
1420 res = bbt_get_entry(this, block);
1422 pr_debug("nand_isbad_bbt(): bbt info for offs 0x%08x: (block %d) 0x%02x\n",
1423 (unsigned int)offs, block, res);
1425 switch (res) {
1426 case BBT_BLOCK_GOOD:
1427 return 0;
1428 case BBT_BLOCK_WORN:
1429 return 1;
1430 case BBT_BLOCK_RESERVED:
1431 return allowbbt ? 0 : 1;
1433 return 1;
1437 * nand_markbad_bbt - [NAND Interface] Mark a block bad in the BBT
1438 * @this: NAND chip object
1439 * @offs: offset of the bad block
1441 int nand_markbad_bbt(struct nand_chip *this, loff_t offs)
1443 int block, ret = 0;
1445 block = (int)(offs >> this->bbt_erase_shift);
1447 /* Mark bad block in memory */
1448 bbt_mark_entry(this, block, BBT_BLOCK_WORN);
1450 /* Update flash-based bad block table */
1451 if (this->bbt_options & NAND_BBT_USE_FLASH)
1452 ret = nand_update_bbt(this, offs);
1454 return ret;