| blob | d870f7067cb7c4f41bf1143887454d47c85f5075 |
1 /* SPDX-License-Identifier: ISC */
2 /*
3 * Copyright (c) 2005-2011 Atheros Communications Inc.
4 * Copyright (c) 2011-2017 Qualcomm Atheros, Inc.
5 * Copyright (c) 2018-2019, The Linux Foundation. All rights reserved.
6 */
8 #ifndef _WMI_H_
9 #define _WMI_H_
11 #include <linux/types.h>
12 #include <linux/ieee80211.h>
14 /*
15 * This file specifies the WMI interface for the Unified Software
16 * Architecture.
17 *
18 * It includes definitions of all the commands and events. Commands are
19 * messages from the host to the target. Events and Replies are messages
20 * from the target to the host.
21 *
22 * Ownership of correctness in regards to WMI commands belongs to the host
23 * driver and the target is not required to validate parameters for value,
24 * proper range, or any other checking.
25 *
26 * Guidelines for extending this interface are below.
27 *
28 * 1. Add new WMI commands ONLY within the specified range - 0x9000 - 0x9fff
29 *
30 * 2. Use ONLY u32 type for defining member variables within WMI
31 * command/event structures. Do not use u8, u16, bool or
32 * enum types within these structures.
33 *
34 * 3. DO NOT define bit fields within structures. Implement bit fields
35 * using masks if necessary. Do not use the programming language's bit
36 * field definition.
37 *
38 * 4. Define macros for encode/decode of u8, u16 fields within
39 * the u32 variables. Use these macros for set/get of these fields.
40 * Try to use this to optimize the structure without bloating it with
41 * u32 variables for every lower sized field.
42 *
43 * 5. Do not use PACK/UNPACK attributes for the structures as each member
44 * variable is already 4-byte aligned by virtue of being a u32
45 * type.
46 *
47 * 6. Comment each parameter part of the WMI command/event structure by
48 * using the 2 stars at the beginning of C comment instead of one star to
49 * enable HTML document generation using Doxygen.
50 *
51 */
53 /* Control Path */
55 __le32 cmd_id;
58 #define WMI_CMD_HDR_CMD_ID_MASK 0x00FFFFFF
59 #define WMI_CMD_HDR_CMD_ID_LSB 0
60 #define WMI_CMD_HDR_PLT_PRIV_MASK 0xFF000000
61 #define WMI_CMD_HDR_PLT_PRIV_LSB 24
63 #define HTC_PROTOCOL_VERSION 0x0002
64 #define WMI_PROTOCOL_VERSION 0x0002
66 /*
67 * There is no signed version of __le32, so for a temporary solution come
68 * up with our own version. The idea is from fs/ntfs/endian.h.
69 *
70 * Use a_ prefix so that it doesn't conflict if we get proper support to
71 * linux/types.h.
72 */
76 {
78 }
81 {
83 }
87 WMI_SERVICE_SCAN_OFFLOAD,
88 WMI_SERVICE_ROAM_OFFLOAD,
89 WMI_SERVICE_BCN_MISS_OFFLOAD,
90 WMI_SERVICE_STA_PWRSAVE,
91 WMI_SERVICE_STA_ADVANCED_PWRSAVE,
92 WMI_SERVICE_AP_UAPSD,
93 WMI_SERVICE_AP_DFS,
94 WMI_SERVICE_11AC,
95 WMI_SERVICE_BLOCKACK,
96 WMI_SERVICE_PHYERR,
97 WMI_SERVICE_BCN_FILTER,
98 WMI_SERVICE_RTT,
99 WMI_SERVICE_RATECTRL,
100 WMI_SERVICE_WOW,
101 WMI_SERVICE_RATECTRL_CACHE,
102 WMI_SERVICE_IRAM_TIDS,
103 WMI_SERVICE_ARPNS_OFFLOAD,
104 WMI_SERVICE_NLO,
105 WMI_SERVICE_GTK_OFFLOAD,
106 WMI_SERVICE_SCAN_SCH,
107 WMI_SERVICE_CSA_OFFLOAD,
108 WMI_SERVICE_CHATTER,
109 WMI_SERVICE_COEX_FREQAVOID,
110 WMI_SERVICE_PACKET_POWER_SAVE,
111 WMI_SERVICE_FORCE_FW_HANG,
112 WMI_SERVICE_GPIO,
113 WMI_SERVICE_STA_DTIM_PS_MODULATED_DTIM,
114 WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
115 WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
116 WMI_SERVICE_STA_KEEP_ALIVE,
117 WMI_SERVICE_TX_ENCAP,
118 WMI_SERVICE_BURST,
119 WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT,
120 WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT,
121 WMI_SERVICE_ROAM_SCAN_OFFLOAD,
122 WMI_SERVICE_AP_PS_DETECT_OUT_OF_SYNC,
123 WMI_SERVICE_EARLY_RX,
124 WMI_SERVICE_STA_SMPS,
125 WMI_SERVICE_FWTEST,
126 WMI_SERVICE_STA_WMMAC,
127 WMI_SERVICE_TDLS,
128 WMI_SERVICE_MCC_BCN_INTERVAL_CHANGE,
129 WMI_SERVICE_ADAPTIVE_OCS,
130 WMI_SERVICE_BA_SSN_SUPPORT,
131 WMI_SERVICE_FILTER_IPSEC_NATKEEPALIVE,
132 WMI_SERVICE_WLAN_HB,
133 WMI_SERVICE_LTE_ANT_SHARE_SUPPORT,
134 WMI_SERVICE_BATCH_SCAN,
135 WMI_SERVICE_QPOWER,
136 WMI_SERVICE_PLMREQ,
137 WMI_SERVICE_THERMAL_MGMT,
138 WMI_SERVICE_RMC,
139 WMI_SERVICE_MHF_OFFLOAD,
140 WMI_SERVICE_COEX_SAR,
141 WMI_SERVICE_BCN_TXRATE_OVERRIDE,
142 WMI_SERVICE_NAN,
143 WMI_SERVICE_L1SS_STAT,
144 WMI_SERVICE_ESTIMATE_LINKSPEED,
145 WMI_SERVICE_OBSS_SCAN,
146 WMI_SERVICE_TDLS_OFFCHAN,
147 WMI_SERVICE_TDLS_UAPSD_BUFFER_STA,
148 WMI_SERVICE_TDLS_UAPSD_SLEEP_STA,
149 WMI_SERVICE_IBSS_PWRSAVE,
150 WMI_SERVICE_LPASS,
151 WMI_SERVICE_EXTSCAN,
152 WMI_SERVICE_D0WOW,
153 WMI_SERVICE_HSOFFLOAD,
154 WMI_SERVICE_ROAM_HO_OFFLOAD,
155 WMI_SERVICE_RX_FULL_REORDER,
156 WMI_SERVICE_DHCP_OFFLOAD,
157 WMI_SERVICE_STA_RX_IPA_OFFLOAD_SUPPORT,
158 WMI_SERVICE_MDNS_OFFLOAD,
159 WMI_SERVICE_SAP_AUTH_OFFLOAD,
160 WMI_SERVICE_ATF,
161 WMI_SERVICE_COEX_GPIO,
162 WMI_SERVICE_ENHANCED_PROXY_STA,
163 WMI_SERVICE_TT,
164 WMI_SERVICE_PEER_CACHING,
165 WMI_SERVICE_AUX_SPECTRAL_INTF,
166 WMI_SERVICE_AUX_CHAN_LOAD_INTF,
167 WMI_SERVICE_BSS_CHANNEL_INFO_64,
168 WMI_SERVICE_EXT_RES_CFG_SUPPORT,
169 WMI_SERVICE_MESH_11S,
170 WMI_SERVICE_MESH_NON_11S,
171 WMI_SERVICE_PEER_STATS,
172 WMI_SERVICE_RESTRT_CHNL_SUPPORT,
173 WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT,
174 WMI_SERVICE_TX_MODE_PUSH_ONLY,
175 WMI_SERVICE_TX_MODE_PUSH_PULL,
176 WMI_SERVICE_TX_MODE_DYNAMIC,
177 WMI_SERVICE_VDEV_RX_FILTER,
178 WMI_SERVICE_BTCOEX,
179 WMI_SERVICE_CHECK_CAL_VERSION,
180 WMI_SERVICE_DBGLOG_WARN2,
181 WMI_SERVICE_BTCOEX_DUTY_CYCLE,
182 WMI_SERVICE_4_WIRE_COEX_SUPPORT,
183 WMI_SERVICE_EXTENDED_NSS_SUPPORT,
184 WMI_SERVICE_PROG_GPIO_BAND_SELECT,
185 WMI_SERVICE_SMART_LOGGING_SUPPORT,
186 WMI_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE,
187 WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY,
188 WMI_SERVICE_MGMT_TX_WMI,
189 WMI_SERVICE_TDLS_WIDER_BANDWIDTH,
190 WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
191 WMI_SERVICE_HOST_DFS_CHECK_SUPPORT,
192 WMI_SERVICE_TPC_STATS_FINAL,
193 WMI_SERVICE_RESET_CHIP,
194 WMI_SERVICE_SPOOF_MAC_SUPPORT,
195 WMI_SERVICE_TX_DATA_ACK_RSSI,
196 WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT,
197 WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT,
198 WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT,
199 WMI_SERVICE_THERM_THROT,
200 WMI_SERVICE_RTT_RESPONDER_ROLE,
201 WMI_SERVICE_PER_PACKET_SW_ENCRYPT,
202 WMI_SERVICE_REPORT_AIRTIME,
203 WMI_SERVICE_SYNC_DELETE_CMDS,
204 WMI_SERVICE_TX_PWR_PER_PEER,
205 WMI_SERVICE_SUPPORT_EXTEND_ADDRESS,
206 WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT,
207 WMI_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT,
209 /* Remember to add the new value to wmi_service_name()! */
211 /* keep last */
212 WMI_SERVICE_MAX,
213 };
217 WMI_10X_SERVICE_SCAN_OFFLOAD,
218 WMI_10X_SERVICE_ROAM_OFFLOAD,
219 WMI_10X_SERVICE_BCN_MISS_OFFLOAD,
220 WMI_10X_SERVICE_STA_PWRSAVE,
221 WMI_10X_SERVICE_STA_ADVANCED_PWRSAVE,
222 WMI_10X_SERVICE_AP_UAPSD,
223 WMI_10X_SERVICE_AP_DFS,
224 WMI_10X_SERVICE_11AC,
225 WMI_10X_SERVICE_BLOCKACK,
226 WMI_10X_SERVICE_PHYERR,
227 WMI_10X_SERVICE_BCN_FILTER,
228 WMI_10X_SERVICE_RTT,
229 WMI_10X_SERVICE_RATECTRL,
230 WMI_10X_SERVICE_WOW,
231 WMI_10X_SERVICE_RATECTRL_CACHE,
232 WMI_10X_SERVICE_IRAM_TIDS,
233 WMI_10X_SERVICE_BURST,
235 /* introduced in 10.2 */
236 WMI_10X_SERVICE_SMART_ANTENNA_SW_SUPPORT,
237 WMI_10X_SERVICE_FORCE_FW_HANG,
238 WMI_10X_SERVICE_SMART_ANTENNA_HW_SUPPORT,
239 WMI_10X_SERVICE_ATF,
240 WMI_10X_SERVICE_COEX_GPIO,
241 WMI_10X_SERVICE_AUX_SPECTRAL_INTF,
242 WMI_10X_SERVICE_AUX_CHAN_LOAD_INTF,
243 WMI_10X_SERVICE_BSS_CHANNEL_INFO_64,
244 WMI_10X_SERVICE_MESH,
245 WMI_10X_SERVICE_EXT_RES_CFG_SUPPORT,
246 WMI_10X_SERVICE_PEER_STATS,
247 WMI_10X_SERVICE_RESET_CHIP,
248 WMI_10X_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
249 WMI_10X_SERVICE_VDEV_BCN_RATE_CONTROL,
250 WMI_10X_SERVICE_PER_PACKET_SW_ENCRYPT,
251 WMI_10X_SERVICE_BB_TIMING_CONFIG_SUPPORT,
252 };
256 WMI_MAIN_SERVICE_SCAN_OFFLOAD,
257 WMI_MAIN_SERVICE_ROAM_OFFLOAD,
258 WMI_MAIN_SERVICE_BCN_MISS_OFFLOAD,
259 WMI_MAIN_SERVICE_STA_PWRSAVE,
260 WMI_MAIN_SERVICE_STA_ADVANCED_PWRSAVE,
261 WMI_MAIN_SERVICE_AP_UAPSD,
262 WMI_MAIN_SERVICE_AP_DFS,
263 WMI_MAIN_SERVICE_11AC,
264 WMI_MAIN_SERVICE_BLOCKACK,
265 WMI_MAIN_SERVICE_PHYERR,
266 WMI_MAIN_SERVICE_BCN_FILTER,
267 WMI_MAIN_SERVICE_RTT,
268 WMI_MAIN_SERVICE_RATECTRL,
269 WMI_MAIN_SERVICE_WOW,
270 WMI_MAIN_SERVICE_RATECTRL_CACHE,
271 WMI_MAIN_SERVICE_IRAM_TIDS,
272 WMI_MAIN_SERVICE_ARPNS_OFFLOAD,
273 WMI_MAIN_SERVICE_NLO,
274 WMI_MAIN_SERVICE_GTK_OFFLOAD,
275 WMI_MAIN_SERVICE_SCAN_SCH,
276 WMI_MAIN_SERVICE_CSA_OFFLOAD,
277 WMI_MAIN_SERVICE_CHATTER,
278 WMI_MAIN_SERVICE_COEX_FREQAVOID,
279 WMI_MAIN_SERVICE_PACKET_POWER_SAVE,
280 WMI_MAIN_SERVICE_FORCE_FW_HANG,
281 WMI_MAIN_SERVICE_GPIO,
282 WMI_MAIN_SERVICE_STA_DTIM_PS_MODULATED_DTIM,
283 WMI_MAIN_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
284 WMI_MAIN_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
285 WMI_MAIN_SERVICE_STA_KEEP_ALIVE,
286 WMI_MAIN_SERVICE_TX_ENCAP,
287 };
291 WMI_10_4_SERVICE_SCAN_OFFLOAD,
292 WMI_10_4_SERVICE_ROAM_OFFLOAD,
293 WMI_10_4_SERVICE_BCN_MISS_OFFLOAD,
294 WMI_10_4_SERVICE_STA_PWRSAVE,
295 WMI_10_4_SERVICE_STA_ADVANCED_PWRSAVE,
296 WMI_10_4_SERVICE_AP_UAPSD,
297 WMI_10_4_SERVICE_AP_DFS,
298 WMI_10_4_SERVICE_11AC,
299 WMI_10_4_SERVICE_BLOCKACK,
300 WMI_10_4_SERVICE_PHYERR,
301 WMI_10_4_SERVICE_BCN_FILTER,
302 WMI_10_4_SERVICE_RTT,
303 WMI_10_4_SERVICE_RATECTRL,
304 WMI_10_4_SERVICE_WOW,
305 WMI_10_4_SERVICE_RATECTRL_CACHE,
306 WMI_10_4_SERVICE_IRAM_TIDS,
307 WMI_10_4_SERVICE_BURST,
308 WMI_10_4_SERVICE_SMART_ANTENNA_SW_SUPPORT,
309 WMI_10_4_SERVICE_GTK_OFFLOAD,
310 WMI_10_4_SERVICE_SCAN_SCH,
311 WMI_10_4_SERVICE_CSA_OFFLOAD,
312 WMI_10_4_SERVICE_CHATTER,
313 WMI_10_4_SERVICE_COEX_FREQAVOID,
314 WMI_10_4_SERVICE_PACKET_POWER_SAVE,
315 WMI_10_4_SERVICE_FORCE_FW_HANG,
316 WMI_10_4_SERVICE_SMART_ANTENNA_HW_SUPPORT,
317 WMI_10_4_SERVICE_GPIO,
318 WMI_10_4_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG,
319 WMI_10_4_SERVICE_STA_UAPSD_VAR_AUTO_TRIG,
320 WMI_10_4_SERVICE_STA_KEEP_ALIVE,
321 WMI_10_4_SERVICE_TX_ENCAP,
322 WMI_10_4_SERVICE_AP_PS_DETECT_OUT_OF_SYNC,
323 WMI_10_4_SERVICE_EARLY_RX,
324 WMI_10_4_SERVICE_ENHANCED_PROXY_STA,
325 WMI_10_4_SERVICE_TT,
326 WMI_10_4_SERVICE_ATF,
327 WMI_10_4_SERVICE_PEER_CACHING,
328 WMI_10_4_SERVICE_COEX_GPIO,
329 WMI_10_4_SERVICE_AUX_SPECTRAL_INTF,
330 WMI_10_4_SERVICE_AUX_CHAN_LOAD_INTF,
331 WMI_10_4_SERVICE_BSS_CHANNEL_INFO_64,
332 WMI_10_4_SERVICE_EXT_RES_CFG_SUPPORT,
333 WMI_10_4_SERVICE_MESH_NON_11S,
334 WMI_10_4_SERVICE_RESTRT_CHNL_SUPPORT,
335 WMI_10_4_SERVICE_PEER_STATS,
336 WMI_10_4_SERVICE_MESH_11S,
337 WMI_10_4_SERVICE_PERIODIC_CHAN_STAT_SUPPORT,
338 WMI_10_4_SERVICE_TX_MODE_PUSH_ONLY,
339 WMI_10_4_SERVICE_TX_MODE_PUSH_PULL,
340 WMI_10_4_SERVICE_TX_MODE_DYNAMIC,
341 WMI_10_4_SERVICE_VDEV_RX_FILTER,
342 WMI_10_4_SERVICE_BTCOEX,
343 WMI_10_4_SERVICE_CHECK_CAL_VERSION,
344 WMI_10_4_SERVICE_DBGLOG_WARN2,
345 WMI_10_4_SERVICE_BTCOEX_DUTY_CYCLE,
346 WMI_10_4_SERVICE_4_WIRE_COEX_SUPPORT,
347 WMI_10_4_SERVICE_EXTENDED_NSS_SUPPORT,
348 WMI_10_4_SERVICE_PROG_GPIO_BAND_SELECT,
349 WMI_10_4_SERVICE_SMART_LOGGING_SUPPORT,
350 WMI_10_4_SERVICE_TDLS,
351 WMI_10_4_SERVICE_TDLS_OFFCHAN,
352 WMI_10_4_SERVICE_TDLS_UAPSD_BUFFER_STA,
353 WMI_10_4_SERVICE_TDLS_UAPSD_SLEEP_STA,
354 WMI_10_4_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE,
355 WMI_10_4_SERVICE_TDLS_EXPLICIT_MODE_ONLY,
356 WMI_10_4_SERVICE_TDLS_WIDER_BANDWIDTH,
357 WMI_10_4_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS,
358 WMI_10_4_SERVICE_HOST_DFS_CHECK_SUPPORT,
359 WMI_10_4_SERVICE_TPC_STATS_FINAL,
360 WMI_10_4_SERVICE_CFR_CAPTURE_SUPPORT,
361 WMI_10_4_SERVICE_TX_DATA_ACK_RSSI,
362 WMI_10_4_SERVICE_CFR_CAPTURE_IND_MSG_TYPE_LEGACY,
363 WMI_10_4_SERVICE_PER_PACKET_SW_ENCRYPT,
364 WMI_10_4_SERVICE_PEER_TID_CONFIGS_SUPPORT,
365 WMI_10_4_SERVICE_VDEV_BCN_RATE_CONTROL,
366 WMI_10_4_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT,
367 WMI_10_4_SERVICE_HTT_ASSERT_TRIGGER_SUPPORT,
368 WMI_10_4_SERVICE_VDEV_FILTER_NEIGHBOR_RX_PACKETS,
369 WMI_10_4_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT,
370 WMI_10_4_SERVICE_PEER_CHWIDTH_CHANGE,
371 WMI_10_4_SERVICE_RX_FILTER_OUT_COUNT,
372 WMI_10_4_SERVICE_RTT_RESPONDER_ROLE,
373 WMI_10_4_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT,
374 WMI_10_4_SERVICE_REPORT_AIRTIME,
375 WMI_10_4_SERVICE_TX_PWR_PER_PEER,
376 WMI_10_4_SERVICE_FETCH_PEER_TX_PN,
377 WMI_10_4_SERVICE_MULTIPLE_VDEV_RESTART,
378 WMI_10_4_SERVICE_ENHANCED_RADIO_COUNTERS,
379 WMI_10_4_SERVICE_QINQ_SUPPORT,
380 WMI_10_4_SERVICE_RESET_CHIP,
381 };
384 {
385 #define SVCSTR(x) case x: return #x
513 }
515 #undef SVCSTR
518 }
520 #define WMI_SERVICE_IS_ENABLED(wmi_svc_bmap, svc_id, len) \
521 ((svc_id) < (len) && \
522 __le32_to_cpu((wmi_svc_bmap)[(svc_id) / (sizeof(u32))]) & \
523 BIT((svc_id) % (sizeof(u32))))
525 /* This extension is required to accommodate new services, current limit
526 * for wmi_services is 64 as target is using only 4-bits of each 32-bit
527 * wmi_service word. Extending this to make use of remaining unused bits
528 * for new services.
529 */
530 #define WMI_EXT_SERVICE_IS_ENABLED(wmi_svc_bmap, svc_id, len) \
531 ((svc_id) >= (len) && \
532 __le32_to_cpu((wmi_svc_bmap)[((svc_id) - (len)) / 28]) & \
533 BIT(((((svc_id) - (len)) % 28) & 0x1f) + 4))
535 #define SVCMAP(x, y, len) \
536 do { \
537 if ((WMI_SERVICE_IS_ENABLED((in), (x), (len))) || \
538 (WMI_EXT_SERVICE_IS_ENABLED((in), (x), (len)))) \
539 __set_bit(y, out); \
540 } while (0)
544 {
611 }
615 {
680 }
684 {
845 }
847 #undef SVCMAP
849 /* 2 word representation of MAC addr */
854 u32 word0;
855 u32 word1;
861 u32 init_cmdid;
862 u32 start_scan_cmdid;
863 u32 stop_scan_cmdid;
864 u32 scan_chan_list_cmdid;
865 u32 scan_sch_prio_tbl_cmdid;
866 u32 scan_prob_req_oui_cmdid;
867 u32 pdev_set_regdomain_cmdid;
868 u32 pdev_set_channel_cmdid;
869 u32 pdev_set_param_cmdid;
870 u32 pdev_pktlog_enable_cmdid;
871 u32 pdev_pktlog_disable_cmdid;
872 u32 pdev_set_wmm_params_cmdid;
873 u32 pdev_set_ht_cap_ie_cmdid;
874 u32 pdev_set_vht_cap_ie_cmdid;
875 u32 pdev_set_dscp_tid_map_cmdid;
876 u32 pdev_set_quiet_mode_cmdid;
877 u32 pdev_green_ap_ps_enable_cmdid;
878 u32 pdev_get_tpc_config_cmdid;
879 u32 pdev_set_base_macaddr_cmdid;
880 u32 vdev_create_cmdid;
881 u32 vdev_delete_cmdid;
882 u32 vdev_start_request_cmdid;
883 u32 vdev_restart_request_cmdid;
884 u32 vdev_up_cmdid;
885 u32 vdev_stop_cmdid;
886 u32 vdev_down_cmdid;
887 u32 vdev_set_param_cmdid;
888 u32 vdev_install_key_cmdid;
889 u32 peer_create_cmdid;
890 u32 peer_delete_cmdid;
891 u32 peer_flush_tids_cmdid;
892 u32 peer_set_param_cmdid;
893 u32 peer_assoc_cmdid;
894 u32 peer_add_wds_entry_cmdid;
895 u32 peer_remove_wds_entry_cmdid;
896 u32 peer_mcast_group_cmdid;
897 u32 bcn_tx_cmdid;
898 u32 pdev_send_bcn_cmdid;
899 u32 bcn_tmpl_cmdid;
900 u32 bcn_filter_rx_cmdid;
901 u32 prb_req_filter_rx_cmdid;
902 u32 mgmt_tx_cmdid;
903 u32 mgmt_tx_send_cmdid;
904 u32 prb_tmpl_cmdid;
905 u32 addba_clear_resp_cmdid;
906 u32 addba_send_cmdid;
907 u32 addba_status_cmdid;
908 u32 delba_send_cmdid;
909 u32 addba_set_resp_cmdid;
910 u32 send_singleamsdu_cmdid;
911 u32 sta_powersave_mode_cmdid;
912 u32 sta_powersave_param_cmdid;
913 u32 sta_mimo_ps_mode_cmdid;
914 u32 pdev_dfs_enable_cmdid;
915 u32 pdev_dfs_disable_cmdid;
916 u32 roam_scan_mode;
917 u32 roam_scan_rssi_threshold;
918 u32 roam_scan_period;
919 u32 roam_scan_rssi_change_threshold;
920 u32 roam_ap_profile;
921 u32 ofl_scan_add_ap_profile;
922 u32 ofl_scan_remove_ap_profile;
923 u32 ofl_scan_period;
924 u32 p2p_dev_set_device_info;
925 u32 p2p_dev_set_discoverability;
926 u32 p2p_go_set_beacon_ie;
927 u32 p2p_go_set_probe_resp_ie;
928 u32 p2p_set_vendor_ie_data_cmdid;
929 u32 ap_ps_peer_param_cmdid;
930 u32 ap_ps_peer_uapsd_coex_cmdid;
931 u32 peer_rate_retry_sched_cmdid;
932 u32 wlan_profile_trigger_cmdid;
933 u32 wlan_profile_set_hist_intvl_cmdid;
934 u32 wlan_profile_get_profile_data_cmdid;
935 u32 wlan_profile_enable_profile_id_cmdid;
936 u32 wlan_profile_list_profile_id_cmdid;
937 u32 pdev_suspend_cmdid;
938 u32 pdev_resume_cmdid;
939 u32 add_bcn_filter_cmdid;
940 u32 rmv_bcn_filter_cmdid;
941 u32 wow_add_wake_pattern_cmdid;
942 u32 wow_del_wake_pattern_cmdid;
943 u32 wow_enable_disable_wake_event_cmdid;
944 u32 wow_enable_cmdid;
945 u32 wow_hostwakeup_from_sleep_cmdid;
946 u32 rtt_measreq_cmdid;
947 u32 rtt_tsf_cmdid;
948 u32 vdev_spectral_scan_configure_cmdid;
949 u32 vdev_spectral_scan_enable_cmdid;
950 u32 request_stats_cmdid;
951 u32 request_peer_stats_info_cmdid;
952 u32 set_arp_ns_offload_cmdid;
953 u32 network_list_offload_config_cmdid;
954 u32 gtk_offload_cmdid;
955 u32 csa_offload_enable_cmdid;
956 u32 csa_offload_chanswitch_cmdid;
957 u32 chatter_set_mode_cmdid;
958 u32 peer_tid_addba_cmdid;
959 u32 peer_tid_delba_cmdid;
960 u32 sta_dtim_ps_method_cmdid;
961 u32 sta_uapsd_auto_trig_cmdid;
962 u32 sta_keepalive_cmd;
963 u32 echo_cmdid;
964 u32 pdev_utf_cmdid;
965 u32 dbglog_cfg_cmdid;
966 u32 pdev_qvit_cmdid;
967 u32 pdev_ftm_intg_cmdid;
968 u32 vdev_set_keepalive_cmdid;
969 u32 vdev_get_keepalive_cmdid;
970 u32 force_fw_hang_cmdid;
971 u32 gpio_config_cmdid;
972 u32 gpio_output_cmdid;
973 u32 pdev_get_temperature_cmdid;
974 u32 vdev_set_wmm_params_cmdid;
975 u32 tdls_set_state_cmdid;
976 u32 tdls_peer_update_cmdid;
977 u32 adaptive_qcs_cmdid;
978 u32 scan_update_request_cmdid;
979 u32 vdev_standby_response_cmdid;
980 u32 vdev_resume_response_cmdid;
981 u32 wlan_peer_caching_add_peer_cmdid;
982 u32 wlan_peer_caching_evict_peer_cmdid;
983 u32 wlan_peer_caching_restore_peer_cmdid;
984 u32 wlan_peer_caching_print_all_peers_info_cmdid;
985 u32 peer_update_wds_entry_cmdid;
986 u32 peer_add_proxy_sta_entry_cmdid;
987 u32 rtt_keepalive_cmdid;
988 u32 oem_req_cmdid;
989 u32 nan_cmdid;
990 u32 vdev_ratemask_cmdid;
991 u32 qboost_cfg_cmdid;
992 u32 pdev_smart_ant_enable_cmdid;
993 u32 pdev_smart_ant_set_rx_antenna_cmdid;
994 u32 peer_smart_ant_set_tx_antenna_cmdid;
995 u32 peer_smart_ant_set_train_info_cmdid;
996 u32 peer_smart_ant_set_node_config_ops_cmdid;
997 u32 pdev_set_antenna_switch_table_cmdid;
998 u32 pdev_set_ctl_table_cmdid;
999 u32 pdev_set_mimogain_table_cmdid;
1000 u32 pdev_ratepwr_table_cmdid;
1001 u32 pdev_ratepwr_chainmsk_table_cmdid;
1002 u32 pdev_fips_cmdid;
1003 u32 tt_set_conf_cmdid;
1004 u32 fwtest_cmdid;
1005 u32 vdev_atf_request_cmdid;
1006 u32 peer_atf_request_cmdid;
1007 u32 pdev_get_ani_cck_config_cmdid;
1008 u32 pdev_get_ani_ofdm_config_cmdid;
1009 u32 pdev_reserve_ast_entry_cmdid;
1010 u32 pdev_get_nfcal_power_cmdid;
1011 u32 pdev_get_tpc_cmdid;
1012 u32 pdev_get_ast_info_cmdid;
1013 u32 vdev_set_dscp_tid_map_cmdid;
1014 u32 pdev_get_info_cmdid;
1015 u32 vdev_get_info_cmdid;
1016 u32 vdev_filter_neighbor_rx_packets_cmdid;
1017 u32 mu_cal_start_cmdid;
1018 u32 set_cca_params_cmdid;
1019 u32 pdev_bss_chan_info_request_cmdid;
1020 u32 pdev_enable_adaptive_cca_cmdid;
1021 u32 ext_resource_cfg_cmdid;
1022 u32 vdev_set_ie_cmdid;
1023 u32 set_lteu_config_cmdid;
1024 u32 atf_ssid_grouping_request_cmdid;
1025 u32 peer_atf_ext_request_cmdid;
1026 u32 set_periodic_channel_stats_cfg_cmdid;
1027 u32 peer_bwf_request_cmdid;
1028 u32 btcoex_cfg_cmdid;
1029 u32 peer_tx_mu_txmit_count_cmdid;
1030 u32 peer_tx_mu_txmit_rstcnt_cmdid;
1031 u32 peer_gid_userpos_list_cmdid;
1032 u32 pdev_check_cal_version_cmdid;
1033 u32 coex_version_cfg_cmid;
1034 u32 pdev_get_rx_filter_cmdid;
1035 u32 pdev_extended_nss_cfg_cmdid;
1036 u32 vdev_set_scan_nac_rssi_cmdid;
1037 u32 prog_gpio_band_select_cmdid;
1038 u32 config_smart_logging_cmdid;
1039 u32 debug_fatal_condition_cmdid;
1040 u32 get_tsf_timer_cmdid;
1041 u32 pdev_get_tpc_table_cmdid;
1042 u32 vdev_sifs_trigger_time_cmdid;
1043 u32 pdev_wds_entry_list_cmdid;
1044 u32 tdls_set_offchan_mode_cmdid;
1045 u32 radar_found_cmdid;
1046 u32 set_bb_timing_cmdid;
1047 u32 per_peer_per_tid_config_cmdid;
1048 };
1050 /*
1051 * wmi command groups.
1052 */
1054 /* 0 to 2 are reserved */
1057 WMI_GRP_PDEV,
1058 WMI_GRP_VDEV,
1059 WMI_GRP_PEER,
1060 WMI_GRP_MGMT,
1061 WMI_GRP_BA_NEG,
1062 WMI_GRP_STA_PS,
1063 WMI_GRP_DFS,
1064 WMI_GRP_ROAM,
1065 WMI_GRP_OFL_SCAN,
1066 WMI_GRP_P2P,
1067 WMI_GRP_AP_PS,
1068 WMI_GRP_RATE_CTRL,
1069 WMI_GRP_PROFILE,
1070 WMI_GRP_SUSPEND,
1071 WMI_GRP_BCN_FILTER,
1072 WMI_GRP_WOW,
1073 WMI_GRP_RTT,
1074 WMI_GRP_SPECTRAL,
1075 WMI_GRP_STATS,
1076 WMI_GRP_ARP_NS_OFL,
1077 WMI_GRP_NLO_OFL,
1078 WMI_GRP_GTK_OFL,
1079 WMI_GRP_CSA_OFL,
1080 WMI_GRP_CHATTER,
1081 WMI_GRP_TID_ADDBA,
1082 WMI_GRP_MISC,
1083 WMI_GRP_GPIO,
1084 };
1086 #define WMI_CMD_GRP(grp_id) (((grp_id) << 12) | 0x1)
1087 #define WMI_EVT_GRP_START_ID(grp_id) (((grp_id) << 12) | 0x1)
1089 #define WMI_CMD_UNSUPPORTED 0
1091 /* Command IDs and command events for MAIN FW. */
1095 /* Scan specific commands */
1097 WMI_STOP_SCAN_CMDID,
1098 WMI_SCAN_CHAN_LIST_CMDID,
1099 WMI_SCAN_SCH_PRIO_TBL_CMDID,
1101 /* PDEV (physical device) specific commands */
1103 WMI_PDEV_SET_CHANNEL_CMDID,
1104 WMI_PDEV_SET_PARAM_CMDID,
1105 WMI_PDEV_PKTLOG_ENABLE_CMDID,
1106 WMI_PDEV_PKTLOG_DISABLE_CMDID,
1107 WMI_PDEV_SET_WMM_PARAMS_CMDID,
1108 WMI_PDEV_SET_HT_CAP_IE_CMDID,
1109 WMI_PDEV_SET_VHT_CAP_IE_CMDID,
1110 WMI_PDEV_SET_DSCP_TID_MAP_CMDID,
1111 WMI_PDEV_SET_QUIET_MODE_CMDID,
1112 WMI_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1113 WMI_PDEV_GET_TPC_CONFIG_CMDID,
1114 WMI_PDEV_SET_BASE_MACADDR_CMDID,
1116 /* VDEV (virtual device) specific commands */
1118 WMI_VDEV_DELETE_CMDID,
1119 WMI_VDEV_START_REQUEST_CMDID,
1120 WMI_VDEV_RESTART_REQUEST_CMDID,
1121 WMI_VDEV_UP_CMDID,
1122 WMI_VDEV_STOP_CMDID,
1123 WMI_VDEV_DOWN_CMDID,
1124 WMI_VDEV_SET_PARAM_CMDID,
1125 WMI_VDEV_INSTALL_KEY_CMDID,
1127 /* peer specific commands */
1129 WMI_PEER_DELETE_CMDID,
1130 WMI_PEER_FLUSH_TIDS_CMDID,
1131 WMI_PEER_SET_PARAM_CMDID,
1132 WMI_PEER_ASSOC_CMDID,
1133 WMI_PEER_ADD_WDS_ENTRY_CMDID,
1134 WMI_PEER_REMOVE_WDS_ENTRY_CMDID,
1135 WMI_PEER_MCAST_GROUP_CMDID,
1137 /* beacon/management specific commands */
1139 WMI_PDEV_SEND_BCN_CMDID,
1140 WMI_BCN_TMPL_CMDID,
1141 WMI_BCN_FILTER_RX_CMDID,
1142 WMI_PRB_REQ_FILTER_RX_CMDID,
1143 WMI_MGMT_TX_CMDID,
1144 WMI_PRB_TMPL_CMDID,
1146 /* commands to directly control BA negotiation directly from host. */
1148 WMI_ADDBA_SEND_CMDID,
1149 WMI_ADDBA_STATUS_CMDID,
1150 WMI_DELBA_SEND_CMDID,
1151 WMI_ADDBA_SET_RESP_CMDID,
1152 WMI_SEND_SINGLEAMSDU_CMDID,
1154 /* Station power save specific config */
1156 WMI_STA_POWERSAVE_PARAM_CMDID,
1157 WMI_STA_MIMO_PS_MODE_CMDID,
1159 /** DFS-specific commands */
1161 WMI_PDEV_DFS_DISABLE_CMDID,
1163 /* Roaming specific commands */
1165 WMI_ROAM_SCAN_RSSI_THRESHOLD,
1166 WMI_ROAM_SCAN_PERIOD,
1167 WMI_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1168 WMI_ROAM_AP_PROFILE,
1170 /* offload scan specific commands */
1172 WMI_OFL_SCAN_REMOVE_AP_PROFILE,
1173 WMI_OFL_SCAN_PERIOD,
1175 /* P2P specific commands */
1177 WMI_P2P_DEV_SET_DISCOVERABILITY,
1178 WMI_P2P_GO_SET_BEACON_IE,
1179 WMI_P2P_GO_SET_PROBE_RESP_IE,
1180 WMI_P2P_SET_VENDOR_IE_DATA_CMDID,
1182 /* AP power save specific config */
1184 WMI_AP_PS_PEER_UAPSD_COEX_CMDID,
1186 /* Rate-control specific commands */
1187 WMI_PEER_RATE_RETRY_SCHED_CMDID =
1190 /* WLAN Profiling commands. */
1192 WMI_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1193 WMI_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1194 WMI_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1195 WMI_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1197 /* Suspend resume command Ids */
1199 WMI_PDEV_RESUME_CMDID,
1201 /* Beacon filter commands */
1203 WMI_RMV_BCN_FILTER_CMDID,
1205 /* WOW Specific WMI commands*/
1207 WMI_WOW_DEL_WAKE_PATTERN_CMDID,
1208 WMI_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1209 WMI_WOW_ENABLE_CMDID,
1210 WMI_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1212 /* RTT measurement related cmd */
1214 WMI_RTT_TSF_CMDID,
1216 /* spectral scan commands */
1218 WMI_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1220 /* F/W stats */
1223 /* ARP OFFLOAD REQUEST*/
1226 /* NS offload confid*/
1229 /* GTK offload Specific WMI commands*/
1232 /* CSA offload Specific WMI commands*/
1234 WMI_CSA_OFFLOAD_CHANSWITCH_CMDID,
1236 /* Chatter commands*/
1239 /* addba specific commands */
1241 WMI_PEER_TID_DELBA_CMDID,
1243 /* set station mimo powersave method */
1244 WMI_STA_DTIM_PS_METHOD_CMDID,
1245 /* Configure the Station UAPSD AC Auto Trigger Parameters */
1246 WMI_STA_UAPSD_AUTO_TRIG_CMDID,
1248 /* STA Keep alive parameter configuration,
1249 * Requires WMI_SERVICE_STA_KEEP_ALIVE
1250 */
1251 WMI_STA_KEEPALIVE_CMD,
1253 /* misc command group */
1255 WMI_PDEV_UTF_CMDID,
1256 WMI_DBGLOG_CFG_CMDID,
1257 WMI_PDEV_QVIT_CMDID,
1258 WMI_PDEV_FTM_INTG_CMDID,
1259 WMI_VDEV_SET_KEEPALIVE_CMDID,
1260 WMI_VDEV_GET_KEEPALIVE_CMDID,
1261 WMI_FORCE_FW_HANG_CMDID,
1263 /* GPIO Configuration */
1265 WMI_GPIO_OUTPUT_CMDID,
1266 };
1270 WMI_READY_EVENTID,
1271 WMI_SERVICE_AVAILABLE_EVENTID,
1273 /* Scan specific events */
1276 /* PDEV specific events */
1278 WMI_CHAN_INFO_EVENTID,
1279 WMI_PHYERR_EVENTID,
1281 /* VDEV specific events */
1283 WMI_VDEV_STOPPED_EVENTID,
1284 WMI_VDEV_INSTALL_KEY_COMPLETE_EVENTID,
1286 /* peer specific events */
1289 /* beacon/mgmt specific events */
1291 WMI_HOST_SWBA_EVENTID,
1292 WMI_TBTTOFFSET_UPDATE_EVENTID,
1294 /* ADDBA Related WMI Events*/
1296 WMI_TX_ADDBA_COMPLETE_EVENTID,
1298 /* Roam event to trigger roaming on host */
1300 WMI_PROFILE_MATCH,
1302 /* WoW */
1305 /* RTT */
1307 WMI_TSF_MEASUREMENT_REPORT_EVENTID,
1308 WMI_RTT_ERROR_REPORT_EVENTID,
1310 /* GTK offload */
1312 WMI_GTK_REKEY_FAIL_EVENTID,
1314 /* CSA IE received event */
1317 /* Misc events */
1319 WMI_PDEV_UTF_EVENTID,
1320 WMI_DEBUG_MESG_EVENTID,
1321 WMI_UPDATE_STATS_EVENTID,
1322 WMI_DEBUG_PRINT_EVENTID,
1323 WMI_DCS_INTERFERENCE_EVENTID,
1324 WMI_PDEV_QVIT_EVENTID,
1325 WMI_WLAN_PROFILE_DATA_EVENTID,
1326 WMI_PDEV_FTM_INTG_EVENTID,
1327 WMI_WLAN_FREQ_AVOID_EVENTID,
1328 WMI_VDEV_GET_KEEPALIVE_EVENTID,
1330 /* GPIO Event */
1332 };
1334 /* Command IDs and command events for 10.X firmware */
1339 /* initialize the wlan sub system */
1340 WMI_10X_INIT_CMDID,
1342 /* Scan specific commands */
1345 WMI_10X_STOP_SCAN_CMDID,
1346 WMI_10X_SCAN_CHAN_LIST_CMDID,
1347 WMI_10X_ECHO_CMDID,
1349 /* PDEV(physical device) specific commands */
1350 WMI_10X_PDEV_SET_REGDOMAIN_CMDID,
1351 WMI_10X_PDEV_SET_CHANNEL_CMDID,
1352 WMI_10X_PDEV_SET_PARAM_CMDID,
1353 WMI_10X_PDEV_PKTLOG_ENABLE_CMDID,
1354 WMI_10X_PDEV_PKTLOG_DISABLE_CMDID,
1355 WMI_10X_PDEV_SET_WMM_PARAMS_CMDID,
1356 WMI_10X_PDEV_SET_HT_CAP_IE_CMDID,
1357 WMI_10X_PDEV_SET_VHT_CAP_IE_CMDID,
1358 WMI_10X_PDEV_SET_BASE_MACADDR_CMDID,
1359 WMI_10X_PDEV_SET_DSCP_TID_MAP_CMDID,
1360 WMI_10X_PDEV_SET_QUIET_MODE_CMDID,
1361 WMI_10X_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1362 WMI_10X_PDEV_GET_TPC_CONFIG_CMDID,
1364 /* VDEV(virtual device) specific commands */
1365 WMI_10X_VDEV_CREATE_CMDID,
1366 WMI_10X_VDEV_DELETE_CMDID,
1367 WMI_10X_VDEV_START_REQUEST_CMDID,
1368 WMI_10X_VDEV_RESTART_REQUEST_CMDID,
1369 WMI_10X_VDEV_UP_CMDID,
1370 WMI_10X_VDEV_STOP_CMDID,
1371 WMI_10X_VDEV_DOWN_CMDID,
1372 WMI_10X_VDEV_STANDBY_RESPONSE_CMDID,
1373 WMI_10X_VDEV_RESUME_RESPONSE_CMDID,
1374 WMI_10X_VDEV_SET_PARAM_CMDID,
1375 WMI_10X_VDEV_INSTALL_KEY_CMDID,
1377 /* peer specific commands */
1378 WMI_10X_PEER_CREATE_CMDID,
1379 WMI_10X_PEER_DELETE_CMDID,
1380 WMI_10X_PEER_FLUSH_TIDS_CMDID,
1381 WMI_10X_PEER_SET_PARAM_CMDID,
1382 WMI_10X_PEER_ASSOC_CMDID,
1383 WMI_10X_PEER_ADD_WDS_ENTRY_CMDID,
1384 WMI_10X_PEER_REMOVE_WDS_ENTRY_CMDID,
1385 WMI_10X_PEER_MCAST_GROUP_CMDID,
1387 /* beacon/management specific commands */
1389 WMI_10X_BCN_TX_CMDID,
1390 WMI_10X_BCN_PRB_TMPL_CMDID,
1391 WMI_10X_BCN_FILTER_RX_CMDID,
1392 WMI_10X_PRB_REQ_FILTER_RX_CMDID,
1393 WMI_10X_MGMT_TX_CMDID,
1395 /* commands to directly control ba negotiation directly from host. */
1396 WMI_10X_ADDBA_CLEAR_RESP_CMDID,
1397 WMI_10X_ADDBA_SEND_CMDID,
1398 WMI_10X_ADDBA_STATUS_CMDID,
1399 WMI_10X_DELBA_SEND_CMDID,
1400 WMI_10X_ADDBA_SET_RESP_CMDID,
1401 WMI_10X_SEND_SINGLEAMSDU_CMDID,
1403 /* Station power save specific config */
1404 WMI_10X_STA_POWERSAVE_MODE_CMDID,
1405 WMI_10X_STA_POWERSAVE_PARAM_CMDID,
1406 WMI_10X_STA_MIMO_PS_MODE_CMDID,
1408 /* set debug log config */
1409 WMI_10X_DBGLOG_CFG_CMDID,
1411 /* DFS-specific commands */
1412 WMI_10X_PDEV_DFS_ENABLE_CMDID,
1413 WMI_10X_PDEV_DFS_DISABLE_CMDID,
1415 /* QVIT specific command id */
1416 WMI_10X_PDEV_QVIT_CMDID,
1418 /* Offload Scan and Roaming related commands */
1419 WMI_10X_ROAM_SCAN_MODE,
1420 WMI_10X_ROAM_SCAN_RSSI_THRESHOLD,
1421 WMI_10X_ROAM_SCAN_PERIOD,
1422 WMI_10X_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1423 WMI_10X_ROAM_AP_PROFILE,
1424 WMI_10X_OFL_SCAN_ADD_AP_PROFILE,
1425 WMI_10X_OFL_SCAN_REMOVE_AP_PROFILE,
1426 WMI_10X_OFL_SCAN_PERIOD,
1428 /* P2P specific commands */
1429 WMI_10X_P2P_DEV_SET_DEVICE_INFO,
1430 WMI_10X_P2P_DEV_SET_DISCOVERABILITY,
1431 WMI_10X_P2P_GO_SET_BEACON_IE,
1432 WMI_10X_P2P_GO_SET_PROBE_RESP_IE,
1434 /* AP power save specific config */
1435 WMI_10X_AP_PS_PEER_PARAM_CMDID,
1436 WMI_10X_AP_PS_PEER_UAPSD_COEX_CMDID,
1438 /* Rate-control specific commands */
1439 WMI_10X_PEER_RATE_RETRY_SCHED_CMDID,
1441 /* WLAN Profiling commands. */
1442 WMI_10X_WLAN_PROFILE_TRIGGER_CMDID,
1443 WMI_10X_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1444 WMI_10X_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1445 WMI_10X_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1446 WMI_10X_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1448 /* Suspend resume command Ids */
1449 WMI_10X_PDEV_SUSPEND_CMDID,
1450 WMI_10X_PDEV_RESUME_CMDID,
1452 /* Beacon filter commands */
1453 WMI_10X_ADD_BCN_FILTER_CMDID,
1454 WMI_10X_RMV_BCN_FILTER_CMDID,
1456 /* WOW Specific WMI commands*/
1457 WMI_10X_WOW_ADD_WAKE_PATTERN_CMDID,
1458 WMI_10X_WOW_DEL_WAKE_PATTERN_CMDID,
1459 WMI_10X_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1460 WMI_10X_WOW_ENABLE_CMDID,
1461 WMI_10X_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1463 /* RTT measurement related cmd */
1464 WMI_10X_RTT_MEASREQ_CMDID,
1465 WMI_10X_RTT_TSF_CMDID,
1467 /* transmit beacon by value */
1468 WMI_10X_PDEV_SEND_BCN_CMDID,
1470 /* F/W stats */
1471 WMI_10X_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
1472 WMI_10X_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1473 WMI_10X_REQUEST_STATS_CMDID,
1475 /* GPIO Configuration */
1476 WMI_10X_GPIO_CONFIG_CMDID,
1477 WMI_10X_GPIO_OUTPUT_CMDID,
1480 };
1484 WMI_10X_READY_EVENTID,
1488 /* Scan specific events */
1490 WMI_10X_ECHO_EVENTID,
1491 WMI_10X_DEBUG_MESG_EVENTID,
1492 WMI_10X_UPDATE_STATS_EVENTID,
1494 /* Instantaneous RSSI event */
1495 WMI_10X_INST_RSSI_STATS_EVENTID,
1497 /* VDEV specific events */
1498 WMI_10X_VDEV_START_RESP_EVENTID,
1499 WMI_10X_VDEV_STANDBY_REQ_EVENTID,
1500 WMI_10X_VDEV_RESUME_REQ_EVENTID,
1501 WMI_10X_VDEV_STOPPED_EVENTID,
1503 /* peer specific events */
1504 WMI_10X_PEER_STA_KICKOUT_EVENTID,
1506 /* beacon/mgmt specific events */
1507 WMI_10X_HOST_SWBA_EVENTID,
1508 WMI_10X_TBTTOFFSET_UPDATE_EVENTID,
1509 WMI_10X_MGMT_RX_EVENTID,
1511 /* Channel stats event */
1512 WMI_10X_CHAN_INFO_EVENTID,
1514 /* PHY Error specific WMI event */
1515 WMI_10X_PHYERR_EVENTID,
1517 /* Roam event to trigger roaming on host */
1518 WMI_10X_ROAM_EVENTID,
1520 /* matching AP found from list of profiles */
1521 WMI_10X_PROFILE_MATCH,
1523 /* debug print message used for tracing FW code while debugging */
1524 WMI_10X_DEBUG_PRINT_EVENTID,
1525 /* VI spoecific event */
1526 WMI_10X_PDEV_QVIT_EVENTID,
1527 /* FW code profile data in response to profile request */
1528 WMI_10X_WLAN_PROFILE_DATA_EVENTID,
1530 /*RTT related event ID*/
1531 WMI_10X_RTT_MEASUREMENT_REPORT_EVENTID,
1532 WMI_10X_TSF_MEASUREMENT_REPORT_EVENTID,
1533 WMI_10X_RTT_ERROR_REPORT_EVENTID,
1535 WMI_10X_WOW_WAKEUP_HOST_EVENTID,
1536 WMI_10X_DCS_INTERFERENCE_EVENTID,
1538 /* TPC config for the current operating channel */
1539 WMI_10X_PDEV_TPC_CONFIG_EVENTID,
1541 WMI_10X_GPIO_INPUT_EVENTID,
1543 };
1548 WMI_10_2_INIT_CMDID,
1550 WMI_10_2_STOP_SCAN_CMDID,
1551 WMI_10_2_SCAN_CHAN_LIST_CMDID,
1552 WMI_10_2_ECHO_CMDID,
1553 WMI_10_2_PDEV_SET_REGDOMAIN_CMDID,
1554 WMI_10_2_PDEV_SET_CHANNEL_CMDID,
1555 WMI_10_2_PDEV_SET_PARAM_CMDID,
1556 WMI_10_2_PDEV_PKTLOG_ENABLE_CMDID,
1557 WMI_10_2_PDEV_PKTLOG_DISABLE_CMDID,
1558 WMI_10_2_PDEV_SET_WMM_PARAMS_CMDID,
1559 WMI_10_2_PDEV_SET_HT_CAP_IE_CMDID,
1560 WMI_10_2_PDEV_SET_VHT_CAP_IE_CMDID,
1561 WMI_10_2_PDEV_SET_BASE_MACADDR_CMDID,
1562 WMI_10_2_PDEV_SET_QUIET_MODE_CMDID,
1563 WMI_10_2_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1564 WMI_10_2_PDEV_GET_TPC_CONFIG_CMDID,
1565 WMI_10_2_VDEV_CREATE_CMDID,
1566 WMI_10_2_VDEV_DELETE_CMDID,
1567 WMI_10_2_VDEV_START_REQUEST_CMDID,
1568 WMI_10_2_VDEV_RESTART_REQUEST_CMDID,
1569 WMI_10_2_VDEV_UP_CMDID,
1570 WMI_10_2_VDEV_STOP_CMDID,
1571 WMI_10_2_VDEV_DOWN_CMDID,
1572 WMI_10_2_VDEV_STANDBY_RESPONSE_CMDID,
1573 WMI_10_2_VDEV_RESUME_RESPONSE_CMDID,
1574 WMI_10_2_VDEV_SET_PARAM_CMDID,
1575 WMI_10_2_VDEV_INSTALL_KEY_CMDID,
1576 WMI_10_2_VDEV_SET_DSCP_TID_MAP_CMDID,
1577 WMI_10_2_PEER_CREATE_CMDID,
1578 WMI_10_2_PEER_DELETE_CMDID,
1579 WMI_10_2_PEER_FLUSH_TIDS_CMDID,
1580 WMI_10_2_PEER_SET_PARAM_CMDID,
1581 WMI_10_2_PEER_ASSOC_CMDID,
1582 WMI_10_2_PEER_ADD_WDS_ENTRY_CMDID,
1583 WMI_10_2_PEER_UPDATE_WDS_ENTRY_CMDID,
1584 WMI_10_2_PEER_REMOVE_WDS_ENTRY_CMDID,
1585 WMI_10_2_PEER_MCAST_GROUP_CMDID,
1586 WMI_10_2_BCN_TX_CMDID,
1587 WMI_10_2_BCN_PRB_TMPL_CMDID,
1588 WMI_10_2_BCN_FILTER_RX_CMDID,
1589 WMI_10_2_PRB_REQ_FILTER_RX_CMDID,
1590 WMI_10_2_MGMT_TX_CMDID,
1591 WMI_10_2_ADDBA_CLEAR_RESP_CMDID,
1592 WMI_10_2_ADDBA_SEND_CMDID,
1593 WMI_10_2_ADDBA_STATUS_CMDID,
1594 WMI_10_2_DELBA_SEND_CMDID,
1595 WMI_10_2_ADDBA_SET_RESP_CMDID,
1596 WMI_10_2_SEND_SINGLEAMSDU_CMDID,
1597 WMI_10_2_STA_POWERSAVE_MODE_CMDID,
1598 WMI_10_2_STA_POWERSAVE_PARAM_CMDID,
1599 WMI_10_2_STA_MIMO_PS_MODE_CMDID,
1600 WMI_10_2_DBGLOG_CFG_CMDID,
1601 WMI_10_2_PDEV_DFS_ENABLE_CMDID,
1602 WMI_10_2_PDEV_DFS_DISABLE_CMDID,
1603 WMI_10_2_PDEV_QVIT_CMDID,
1604 WMI_10_2_ROAM_SCAN_MODE,
1605 WMI_10_2_ROAM_SCAN_RSSI_THRESHOLD,
1606 WMI_10_2_ROAM_SCAN_PERIOD,
1607 WMI_10_2_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1608 WMI_10_2_ROAM_AP_PROFILE,
1609 WMI_10_2_OFL_SCAN_ADD_AP_PROFILE,
1610 WMI_10_2_OFL_SCAN_REMOVE_AP_PROFILE,
1611 WMI_10_2_OFL_SCAN_PERIOD,
1612 WMI_10_2_P2P_DEV_SET_DEVICE_INFO,
1613 WMI_10_2_P2P_DEV_SET_DISCOVERABILITY,
1614 WMI_10_2_P2P_GO_SET_BEACON_IE,
1615 WMI_10_2_P2P_GO_SET_PROBE_RESP_IE,
1616 WMI_10_2_AP_PS_PEER_PARAM_CMDID,
1617 WMI_10_2_AP_PS_PEER_UAPSD_COEX_CMDID,
1618 WMI_10_2_PEER_RATE_RETRY_SCHED_CMDID,
1619 WMI_10_2_WLAN_PROFILE_TRIGGER_CMDID,
1620 WMI_10_2_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1621 WMI_10_2_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1622 WMI_10_2_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1623 WMI_10_2_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1624 WMI_10_2_PDEV_SUSPEND_CMDID,
1625 WMI_10_2_PDEV_RESUME_CMDID,
1626 WMI_10_2_ADD_BCN_FILTER_CMDID,
1627 WMI_10_2_RMV_BCN_FILTER_CMDID,
1628 WMI_10_2_WOW_ADD_WAKE_PATTERN_CMDID,
1629 WMI_10_2_WOW_DEL_WAKE_PATTERN_CMDID,
1630 WMI_10_2_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1631 WMI_10_2_WOW_ENABLE_CMDID,
1632 WMI_10_2_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1633 WMI_10_2_RTT_MEASREQ_CMDID,
1634 WMI_10_2_RTT_TSF_CMDID,
1635 WMI_10_2_RTT_KEEPALIVE_CMDID,
1636 WMI_10_2_PDEV_SEND_BCN_CMDID,
1637 WMI_10_2_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
1638 WMI_10_2_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1639 WMI_10_2_REQUEST_STATS_CMDID,
1640 WMI_10_2_GPIO_CONFIG_CMDID,
1641 WMI_10_2_GPIO_OUTPUT_CMDID,
1642 WMI_10_2_VDEV_RATEMASK_CMDID,
1643 WMI_10_2_PDEV_SMART_ANT_ENABLE_CMDID,
1644 WMI_10_2_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID,
1645 WMI_10_2_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID,
1646 WMI_10_2_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID,
1647 WMI_10_2_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID,
1648 WMI_10_2_FORCE_FW_HANG_CMDID,
1649 WMI_10_2_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID,
1650 WMI_10_2_PDEV_SET_CTL_TABLE_CMDID,
1651 WMI_10_2_PDEV_SET_MIMOGAIN_TABLE_CMDID,
1652 WMI_10_2_PDEV_RATEPWR_TABLE_CMDID,
1653 WMI_10_2_PDEV_RATEPWR_CHAINMSK_TABLE_CMDID,
1654 WMI_10_2_PDEV_GET_INFO,
1655 WMI_10_2_VDEV_GET_INFO,
1656 WMI_10_2_VDEV_ATF_REQUEST_CMDID,
1657 WMI_10_2_PEER_ATF_REQUEST_CMDID,
1658 WMI_10_2_PDEV_GET_TEMPERATURE_CMDID,
1659 WMI_10_2_MU_CAL_START_CMDID,
1660 WMI_10_2_SET_LTEU_CONFIG_CMDID,
1661 WMI_10_2_SET_CCA_PARAMS,
1662 WMI_10_2_PDEV_BSS_CHAN_INFO_REQUEST_CMDID,
1663 WMI_10_2_FWTEST_CMDID,
1664 WMI_10_2_PDEV_SET_BB_TIMING_CONFIG_CMDID,
1666 };
1670 WMI_10_2_READY_EVENTID,
1671 WMI_10_2_DEBUG_MESG_EVENTID,
1675 WMI_10_2_ECHO_EVENTID,
1676 WMI_10_2_UPDATE_STATS_EVENTID,
1677 WMI_10_2_INST_RSSI_STATS_EVENTID,
1678 WMI_10_2_VDEV_START_RESP_EVENTID,
1679 WMI_10_2_VDEV_STANDBY_REQ_EVENTID,
1680 WMI_10_2_VDEV_RESUME_REQ_EVENTID,
1681 WMI_10_2_VDEV_STOPPED_EVENTID,
1682 WMI_10_2_PEER_STA_KICKOUT_EVENTID,
1683 WMI_10_2_HOST_SWBA_EVENTID,
1684 WMI_10_2_TBTTOFFSET_UPDATE_EVENTID,
1685 WMI_10_2_MGMT_RX_EVENTID,
1686 WMI_10_2_CHAN_INFO_EVENTID,
1687 WMI_10_2_PHYERR_EVENTID,
1688 WMI_10_2_ROAM_EVENTID,
1689 WMI_10_2_PROFILE_MATCH,
1690 WMI_10_2_DEBUG_PRINT_EVENTID,
1691 WMI_10_2_PDEV_QVIT_EVENTID,
1692 WMI_10_2_WLAN_PROFILE_DATA_EVENTID,
1693 WMI_10_2_RTT_MEASUREMENT_REPORT_EVENTID,
1694 WMI_10_2_TSF_MEASUREMENT_REPORT_EVENTID,
1695 WMI_10_2_RTT_ERROR_REPORT_EVENTID,
1696 WMI_10_2_RTT_KEEPALIVE_EVENTID,
1697 WMI_10_2_WOW_WAKEUP_HOST_EVENTID,
1698 WMI_10_2_DCS_INTERFERENCE_EVENTID,
1699 WMI_10_2_PDEV_TPC_CONFIG_EVENTID,
1700 WMI_10_2_GPIO_INPUT_EVENTID,
1701 WMI_10_2_PEER_RATECODE_LIST_EVENTID,
1702 WMI_10_2_GENERIC_BUFFER_EVENTID,
1703 WMI_10_2_MCAST_BUF_RELEASE_EVENTID,
1704 WMI_10_2_MCAST_LIST_AGEOUT_EVENTID,
1705 WMI_10_2_WDS_PEER_EVENTID,
1706 WMI_10_2_PEER_STA_PS_STATECHG_EVENTID,
1707 WMI_10_2_PDEV_TEMPERATURE_EVENTID,
1708 WMI_10_2_MU_REPORT_EVENTID,
1709 WMI_10_2_PDEV_BSS_CHAN_INFO_EVENTID,
1711 };
1716 WMI_10_4_INIT_CMDID,
1718 WMI_10_4_STOP_SCAN_CMDID,
1719 WMI_10_4_SCAN_CHAN_LIST_CMDID,
1720 WMI_10_4_SCAN_SCH_PRIO_TBL_CMDID,
1721 WMI_10_4_SCAN_UPDATE_REQUEST_CMDID,
1722 WMI_10_4_ECHO_CMDID,
1723 WMI_10_4_PDEV_SET_REGDOMAIN_CMDID,
1724 WMI_10_4_PDEV_SET_CHANNEL_CMDID,
1725 WMI_10_4_PDEV_SET_PARAM_CMDID,
1726 WMI_10_4_PDEV_PKTLOG_ENABLE_CMDID,
1727 WMI_10_4_PDEV_PKTLOG_DISABLE_CMDID,
1728 WMI_10_4_PDEV_SET_WMM_PARAMS_CMDID,
1729 WMI_10_4_PDEV_SET_HT_CAP_IE_CMDID,
1730 WMI_10_4_PDEV_SET_VHT_CAP_IE_CMDID,
1731 WMI_10_4_PDEV_SET_BASE_MACADDR_CMDID,
1732 WMI_10_4_PDEV_SET_DSCP_TID_MAP_CMDID,
1733 WMI_10_4_PDEV_SET_QUIET_MODE_CMDID,
1734 WMI_10_4_PDEV_GREEN_AP_PS_ENABLE_CMDID,
1735 WMI_10_4_PDEV_GET_TPC_CONFIG_CMDID,
1736 WMI_10_4_VDEV_CREATE_CMDID,
1737 WMI_10_4_VDEV_DELETE_CMDID,
1738 WMI_10_4_VDEV_START_REQUEST_CMDID,
1739 WMI_10_4_VDEV_RESTART_REQUEST_CMDID,
1740 WMI_10_4_VDEV_UP_CMDID,
1741 WMI_10_4_VDEV_STOP_CMDID,
1742 WMI_10_4_VDEV_DOWN_CMDID,
1743 WMI_10_4_VDEV_STANDBY_RESPONSE_CMDID,
1744 WMI_10_4_VDEV_RESUME_RESPONSE_CMDID,
1745 WMI_10_4_VDEV_SET_PARAM_CMDID,
1746 WMI_10_4_VDEV_INSTALL_KEY_CMDID,
1747 WMI_10_4_WLAN_PEER_CACHING_ADD_PEER_CMDID,
1748 WMI_10_4_WLAN_PEER_CACHING_EVICT_PEER_CMDID,
1749 WMI_10_4_WLAN_PEER_CACHING_RESTORE_PEER_CMDID,
1750 WMI_10_4_WLAN_PEER_CACHING_PRINT_ALL_PEERS_INFO_CMDID,
1751 WMI_10_4_PEER_CREATE_CMDID,
1752 WMI_10_4_PEER_DELETE_CMDID,
1753 WMI_10_4_PEER_FLUSH_TIDS_CMDID,
1754 WMI_10_4_PEER_SET_PARAM_CMDID,
1755 WMI_10_4_PEER_ASSOC_CMDID,
1756 WMI_10_4_PEER_ADD_WDS_ENTRY_CMDID,
1757 WMI_10_4_PEER_UPDATE_WDS_ENTRY_CMDID,
1758 WMI_10_4_PEER_REMOVE_WDS_ENTRY_CMDID,
1759 WMI_10_4_PEER_ADD_PROXY_STA_ENTRY_CMDID,
1760 WMI_10_4_PEER_MCAST_GROUP_CMDID,
1761 WMI_10_4_BCN_TX_CMDID,
1762 WMI_10_4_PDEV_SEND_BCN_CMDID,
1763 WMI_10_4_BCN_PRB_TMPL_CMDID,
1764 WMI_10_4_BCN_FILTER_RX_CMDID,
1765 WMI_10_4_PRB_REQ_FILTER_RX_CMDID,
1766 WMI_10_4_MGMT_TX_CMDID,
1767 WMI_10_4_PRB_TMPL_CMDID,
1768 WMI_10_4_ADDBA_CLEAR_RESP_CMDID,
1769 WMI_10_4_ADDBA_SEND_CMDID,
1770 WMI_10_4_ADDBA_STATUS_CMDID,
1771 WMI_10_4_DELBA_SEND_CMDID,
1772 WMI_10_4_ADDBA_SET_RESP_CMDID,
1773 WMI_10_4_SEND_SINGLEAMSDU_CMDID,
1774 WMI_10_4_STA_POWERSAVE_MODE_CMDID,
1775 WMI_10_4_STA_POWERSAVE_PARAM_CMDID,
1776 WMI_10_4_STA_MIMO_PS_MODE_CMDID,
1777 WMI_10_4_DBGLOG_CFG_CMDID,
1778 WMI_10_4_PDEV_DFS_ENABLE_CMDID,
1779 WMI_10_4_PDEV_DFS_DISABLE_CMDID,
1780 WMI_10_4_PDEV_QVIT_CMDID,
1781 WMI_10_4_ROAM_SCAN_MODE,
1782 WMI_10_4_ROAM_SCAN_RSSI_THRESHOLD,
1783 WMI_10_4_ROAM_SCAN_PERIOD,
1784 WMI_10_4_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
1785 WMI_10_4_ROAM_AP_PROFILE,
1786 WMI_10_4_OFL_SCAN_ADD_AP_PROFILE,
1787 WMI_10_4_OFL_SCAN_REMOVE_AP_PROFILE,
1788 WMI_10_4_OFL_SCAN_PERIOD,
1789 WMI_10_4_P2P_DEV_SET_DEVICE_INFO,
1790 WMI_10_4_P2P_DEV_SET_DISCOVERABILITY,
1791 WMI_10_4_P2P_GO_SET_BEACON_IE,
1792 WMI_10_4_P2P_GO_SET_PROBE_RESP_IE,
1793 WMI_10_4_P2P_SET_VENDOR_IE_DATA_CMDID,
1794 WMI_10_4_AP_PS_PEER_PARAM_CMDID,
1795 WMI_10_4_AP_PS_PEER_UAPSD_COEX_CMDID,
1796 WMI_10_4_PEER_RATE_RETRY_SCHED_CMDID,
1797 WMI_10_4_WLAN_PROFILE_TRIGGER_CMDID,
1798 WMI_10_4_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
1799 WMI_10_4_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
1800 WMI_10_4_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
1801 WMI_10_4_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
1802 WMI_10_4_PDEV_SUSPEND_CMDID,
1803 WMI_10_4_PDEV_RESUME_CMDID,
1804 WMI_10_4_ADD_BCN_FILTER_CMDID,
1805 WMI_10_4_RMV_BCN_FILTER_CMDID,
1806 WMI_10_4_WOW_ADD_WAKE_PATTERN_CMDID,
1807 WMI_10_4_WOW_DEL_WAKE_PATTERN_CMDID,
1808 WMI_10_4_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
1809 WMI_10_4_WOW_ENABLE_CMDID,
1810 WMI_10_4_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
1811 WMI_10_4_RTT_MEASREQ_CMDID,
1812 WMI_10_4_RTT_TSF_CMDID,
1813 WMI_10_4_RTT_KEEPALIVE_CMDID,
1814 WMI_10_4_OEM_REQ_CMDID,
1815 WMI_10_4_NAN_CMDID,
1816 WMI_10_4_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
1817 WMI_10_4_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
1818 WMI_10_4_REQUEST_STATS_CMDID,
1819 WMI_10_4_GPIO_CONFIG_CMDID,
1820 WMI_10_4_GPIO_OUTPUT_CMDID,
1821 WMI_10_4_VDEV_RATEMASK_CMDID,
1822 WMI_10_4_CSA_OFFLOAD_ENABLE_CMDID,
1823 WMI_10_4_GTK_OFFLOAD_CMDID,
1824 WMI_10_4_QBOOST_CFG_CMDID,
1825 WMI_10_4_CSA_OFFLOAD_CHANSWITCH_CMDID,
1826 WMI_10_4_PDEV_SMART_ANT_ENABLE_CMDID,
1827 WMI_10_4_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID,
1828 WMI_10_4_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID,
1829 WMI_10_4_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID,
1830 WMI_10_4_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID,
1831 WMI_10_4_VDEV_SET_KEEPALIVE_CMDID,
1832 WMI_10_4_VDEV_GET_KEEPALIVE_CMDID,
1833 WMI_10_4_FORCE_FW_HANG_CMDID,
1834 WMI_10_4_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID,
1835 WMI_10_4_PDEV_SET_CTL_TABLE_CMDID,
1836 WMI_10_4_PDEV_SET_MIMOGAIN_TABLE_CMDID,
1837 WMI_10_4_PDEV_RATEPWR_TABLE_CMDID,
1838 WMI_10_4_PDEV_RATEPWR_CHAINMSK_TABLE_CMDID,
1839 WMI_10_4_PDEV_FIPS_CMDID,
1840 WMI_10_4_TT_SET_CONF_CMDID,
1841 WMI_10_4_FWTEST_CMDID,
1842 WMI_10_4_VDEV_ATF_REQUEST_CMDID,
1843 WMI_10_4_PEER_ATF_REQUEST_CMDID,
1844 WMI_10_4_PDEV_GET_ANI_CCK_CONFIG_CMDID,
1845 WMI_10_4_PDEV_GET_ANI_OFDM_CONFIG_CMDID,
1846 WMI_10_4_PDEV_RESERVE_AST_ENTRY_CMDID,
1847 WMI_10_4_PDEV_GET_NFCAL_POWER_CMDID,
1848 WMI_10_4_PDEV_GET_TPC_CMDID,
1849 WMI_10_4_PDEV_GET_AST_INFO_CMDID,
1850 WMI_10_4_VDEV_SET_DSCP_TID_MAP_CMDID,
1851 WMI_10_4_PDEV_GET_TEMPERATURE_CMDID,
1852 WMI_10_4_PDEV_GET_INFO_CMDID,
1853 WMI_10_4_VDEV_GET_INFO_CMDID,
1854 WMI_10_4_VDEV_FILTER_NEIGHBOR_RX_PACKETS_CMDID,
1855 WMI_10_4_MU_CAL_START_CMDID,
1856 WMI_10_4_SET_CCA_PARAMS_CMDID,
1857 WMI_10_4_PDEV_BSS_CHAN_INFO_REQUEST_CMDID,
1858 WMI_10_4_EXT_RESOURCE_CFG_CMDID,
1859 WMI_10_4_VDEV_SET_IE_CMDID,
1860 WMI_10_4_SET_LTEU_CONFIG_CMDID,
1861 WMI_10_4_ATF_SSID_GROUPING_REQUEST_CMDID,
1862 WMI_10_4_PEER_ATF_EXT_REQUEST_CMDID,
1863 WMI_10_4_SET_PERIODIC_CHANNEL_STATS_CONFIG,
1864 WMI_10_4_PEER_BWF_REQUEST_CMDID,
1865 WMI_10_4_BTCOEX_CFG_CMDID,
1866 WMI_10_4_PEER_TX_MU_TXMIT_COUNT_CMDID,
1867 WMI_10_4_PEER_TX_MU_TXMIT_RSTCNT_CMDID,
1868 WMI_10_4_PEER_GID_USERPOS_LIST_CMDID,
1869 WMI_10_4_PDEV_CHECK_CAL_VERSION_CMDID,
1870 WMI_10_4_COEX_VERSION_CFG_CMID,
1871 WMI_10_4_PDEV_GET_RX_FILTER_CMDID,
1872 WMI_10_4_PDEV_EXTENDED_NSS_CFG_CMDID,
1873 WMI_10_4_VDEV_SET_SCAN_NAC_RSSI_CMDID,
1874 WMI_10_4_PROG_GPIO_BAND_SELECT_CMDID,
1875 WMI_10_4_CONFIG_SMART_LOGGING_CMDID,
1876 WMI_10_4_DEBUG_FATAL_CONDITION_CMDID,
1877 WMI_10_4_GET_TSF_TIMER_CMDID,
1878 WMI_10_4_PDEV_GET_TPC_TABLE_CMDID,
1879 WMI_10_4_VDEV_SIFS_TRIGGER_TIME_CMDID,
1880 WMI_10_4_PDEV_WDS_ENTRY_LIST_CMDID,
1881 WMI_10_4_TDLS_SET_STATE_CMDID,
1882 WMI_10_4_TDLS_PEER_UPDATE_CMDID,
1883 WMI_10_4_TDLS_SET_OFFCHAN_MODE_CMDID,
1884 WMI_10_4_PDEV_SEND_FD_CMDID,
1885 WMI_10_4_ENABLE_FILS_CMDID,
1886 WMI_10_4_PDEV_SET_BRIDGE_MACADDR_CMDID,
1887 WMI_10_4_ATF_GROUP_WMM_AC_CONFIG_REQUEST_CMDID,
1888 WMI_10_4_RADAR_FOUND_CMDID,
1889 WMI_10_4_PEER_CFR_CAPTURE_CMDID,
1890 WMI_10_4_PER_PEER_PER_TID_CONFIG_CMDID,
1892 };
1896 WMI_10_4_READY_EVENTID,
1897 WMI_10_4_DEBUG_MESG_EVENTID,
1901 WMI_10_4_ECHO_EVENTID,
1902 WMI_10_4_UPDATE_STATS_EVENTID,
1903 WMI_10_4_INST_RSSI_STATS_EVENTID,
1904 WMI_10_4_VDEV_START_RESP_EVENTID,
1905 WMI_10_4_VDEV_STANDBY_REQ_EVENTID,
1906 WMI_10_4_VDEV_RESUME_REQ_EVENTID,
1907 WMI_10_4_VDEV_STOPPED_EVENTID,
1908 WMI_10_4_PEER_STA_KICKOUT_EVENTID,
1909 WMI_10_4_HOST_SWBA_EVENTID,
1910 WMI_10_4_TBTTOFFSET_UPDATE_EVENTID,
1911 WMI_10_4_MGMT_RX_EVENTID,
1912 WMI_10_4_CHAN_INFO_EVENTID,
1913 WMI_10_4_PHYERR_EVENTID,
1914 WMI_10_4_ROAM_EVENTID,
1915 WMI_10_4_PROFILE_MATCH,
1916 WMI_10_4_DEBUG_PRINT_EVENTID,
1917 WMI_10_4_PDEV_QVIT_EVENTID,
1918 WMI_10_4_WLAN_PROFILE_DATA_EVENTID,
1919 WMI_10_4_RTT_MEASUREMENT_REPORT_EVENTID,
1920 WMI_10_4_TSF_MEASUREMENT_REPORT_EVENTID,
1921 WMI_10_4_RTT_ERROR_REPORT_EVENTID,
1922 WMI_10_4_RTT_KEEPALIVE_EVENTID,
1923 WMI_10_4_OEM_CAPABILITY_EVENTID,
1924 WMI_10_4_OEM_MEASUREMENT_REPORT_EVENTID,
1925 WMI_10_4_OEM_ERROR_REPORT_EVENTID,
1926 WMI_10_4_NAN_EVENTID,
1927 WMI_10_4_WOW_WAKEUP_HOST_EVENTID,
1928 WMI_10_4_GTK_OFFLOAD_STATUS_EVENTID,
1929 WMI_10_4_GTK_REKEY_FAIL_EVENTID,
1930 WMI_10_4_DCS_INTERFERENCE_EVENTID,
1931 WMI_10_4_PDEV_TPC_CONFIG_EVENTID,
1932 WMI_10_4_CSA_HANDLING_EVENTID,
1933 WMI_10_4_GPIO_INPUT_EVENTID,
1934 WMI_10_4_PEER_RATECODE_LIST_EVENTID,
1935 WMI_10_4_GENERIC_BUFFER_EVENTID,
1936 WMI_10_4_MCAST_BUF_RELEASE_EVENTID,
1937 WMI_10_4_MCAST_LIST_AGEOUT_EVENTID,
1938 WMI_10_4_VDEV_GET_KEEPALIVE_EVENTID,
1939 WMI_10_4_WDS_PEER_EVENTID,
1940 WMI_10_4_PEER_STA_PS_STATECHG_EVENTID,
1941 WMI_10_4_PDEV_FIPS_EVENTID,
1942 WMI_10_4_TT_STATS_EVENTID,
1943 WMI_10_4_PDEV_CHANNEL_HOPPING_EVENTID,
1944 WMI_10_4_PDEV_ANI_CCK_LEVEL_EVENTID,
1945 WMI_10_4_PDEV_ANI_OFDM_LEVEL_EVENTID,
1946 WMI_10_4_PDEV_RESERVE_AST_ENTRY_EVENTID,
1947 WMI_10_4_PDEV_NFCAL_POWER_EVENTID,
1948 WMI_10_4_PDEV_TPC_EVENTID,
1949 WMI_10_4_PDEV_GET_AST_INFO_EVENTID,
1950 WMI_10_4_PDEV_TEMPERATURE_EVENTID,
1951 WMI_10_4_PDEV_NFCAL_POWER_ALL_CHANNELS_EVENTID,
1952 WMI_10_4_PDEV_BSS_CHAN_INFO_EVENTID,
1953 WMI_10_4_MU_REPORT_EVENTID,
1954 WMI_10_4_TX_DATA_TRAFFIC_CTRL_EVENTID,
1955 WMI_10_4_PEER_TX_MU_TXMIT_COUNT_EVENTID,
1956 WMI_10_4_PEER_GID_USERPOS_LIST_EVENTID,
1957 WMI_10_4_PDEV_CHECK_CAL_VERSION_EVENTID,
1958 WMI_10_4_ATF_PEER_STATS_EVENTID,
1959 WMI_10_4_PDEV_GET_RX_FILTER_EVENTID,
1960 WMI_10_4_NAC_RSSI_EVENTID,
1961 WMI_10_4_DEBUG_FATAL_CONDITION_EVENTID,
1962 WMI_10_4_GET_TSF_TIMER_RESP_EVENTID,
1963 WMI_10_4_PDEV_TPC_TABLE_EVENTID,
1964 WMI_10_4_PDEV_WDS_ENTRY_LIST_EVENTID,
1965 WMI_10_4_TDLS_PEER_EVENTID,
1966 WMI_10_4_HOST_SWFDA_EVENTID,
1967 WMI_10_4_ESP_ESTIMATE_EVENTID,
1968 WMI_10_4_DFS_STATUS_CHECK_EVENTID,
1970 };
1984 /* MODE_11AC_VHT160 = 11, */
1992 };
1995 {
2030 /* skip */
2033 /* no default handler to allow compiler to check that the
2034 * enum is fully handled
2035 */
2036 }
2039 }
2041 #define WMI_CHAN_LIST_TAG 0x1
2042 #define WMI_SSID_LIST_TAG 0x2
2043 #define WMI_BSSID_LIST_TAG 0x3
2044 #define WMI_IE_TAG 0x4
2047 __le32 mhz;
2048 __le32 band_center_freq1;
2057 __le32 reginfo0;
2059 /* note: power unit is 0.5 dBm */
2060 u8 min_power;
2061 u8 max_power;
2062 u8 reg_power;
2063 u8 reg_classid;
2067 __le32 reginfo1;
2069 u8 antenna_max;
2070 u8 max_tx_power;
2076 u32 freq;
2077 u32 band_center_freq1;
2078 u32 band_center_freq2;
2085 /* note: power unit is 0.5 dBm */
2086 u32 min_power;
2087 u32 max_power;
2088 u32 max_reg_power;
2089 u32 max_antenna_gain;
2090 u32 reg_class_id;
2092 };
2096 WMI_CHANNEL_CHANGE_CAUSE_CSA,
2097 };
2099 #define WMI_CHAN_FLAG_HT40_PLUS (1 << 6)
2100 #define WMI_CHAN_FLAG_PASSIVE (1 << 7)
2101 #define WMI_CHAN_FLAG_ADHOC_ALLOWED (1 << 8)
2102 #define WMI_CHAN_FLAG_AP_DISABLED (1 << 9)
2103 #define WMI_CHAN_FLAG_DFS (1 << 10)
2104 #define WMI_CHAN_FLAG_ALLOW_HT (1 << 11)
2105 #define WMI_CHAN_FLAG_ALLOW_VHT (1 << 12)
2107 /* Indicate reason for channel switch */
2108 #define WMI_CHANNEL_CHANGE_CAUSE_CSA (1 << 13)
2109 /* DFS required on channel for 2nd segment of VHT160 and VHT80+80*/
2110 #define WMI_CHAN_FLAG_DFS_CFREQ2 (1 << 15)
2113 /* HT Capabilities*/
2118 #define WMI_HT_CAP_TX_STBC_MASK_SHIFT 3
2120 #define WMI_HT_CAP_RX_STBC_MASK_SHIFT 4
2124 #define WMI_HT_CAP_MPDU_DENSITY_MASK_SHIFT 8
2125 #define WMI_HT_CAP_HT40_SGI 0x0800
2129 #define WMI_HT_CAP_DEFAULT_ALL (WMI_HT_CAP_ENABLED | \
2130 WMI_HT_CAP_HT20_SGI | \
2131 WMI_HT_CAP_HT40_SGI | \
2132 WMI_HT_CAP_TX_STBC | \
2133 WMI_HT_CAP_RX_STBC | \
2134 WMI_HT_CAP_LDPC)
2136 /*
2137 * WMI_VHT_CAP_* these maps to ieee 802.11ac vht capability information
2138 * field. The fields not defined here are not supported, or reserved.
2139 * Do not change these masks and if you have to add new one follow the
2140 * bitmask as specified by 802.11ac draft.
2141 */
2143 #define WMI_VHT_CAP_MAX_MPDU_LEN_MASK 0x00000003
2144 #define WMI_VHT_CAP_RX_LDPC 0x00000010
2145 #define WMI_VHT_CAP_SGI_80MHZ 0x00000020
2146 #define WMI_VHT_CAP_SGI_160MHZ 0x00000040
2147 #define WMI_VHT_CAP_TX_STBC 0x00000080
2148 #define WMI_VHT_CAP_RX_STBC_MASK 0x00000300
2149 #define WMI_VHT_CAP_RX_STBC_MASK_SHIFT 8
2150 #define WMI_VHT_CAP_SU_BFER 0x00000800
2151 #define WMI_VHT_CAP_SU_BFEE 0x00001000
2152 #define WMI_VHT_CAP_MAX_CS_ANT_MASK 0x0000E000
2153 #define WMI_VHT_CAP_MAX_CS_ANT_MASK_SHIFT 13
2154 #define WMI_VHT_CAP_MAX_SND_DIM_MASK 0x00070000
2155 #define WMI_VHT_CAP_MAX_SND_DIM_MASK_SHIFT 16
2156 #define WMI_VHT_CAP_MU_BFER 0x00080000
2157 #define WMI_VHT_CAP_MU_BFEE 0x00100000
2158 #define WMI_VHT_CAP_MAX_AMPDU_LEN_EXP 0x03800000
2159 #define WMI_VHT_CAP_MAX_AMPDU_LEN_EXP_SHIFT 23
2160 #define WMI_VHT_CAP_RX_FIXED_ANT 0x10000000
2161 #define WMI_VHT_CAP_TX_FIXED_ANT 0x20000000
2163 /* The following also refer for max HT AMSDU */
2164 #define WMI_VHT_CAP_MAX_MPDU_LEN_3839 0x00000000
2165 #define WMI_VHT_CAP_MAX_MPDU_LEN_7935 0x00000001
2166 #define WMI_VHT_CAP_MAX_MPDU_LEN_11454 0x00000002
2168 #define WMI_VHT_CAP_DEFAULT_ALL (WMI_VHT_CAP_MAX_MPDU_LEN_11454 | \
2169 WMI_VHT_CAP_RX_LDPC | \
2170 WMI_VHT_CAP_SGI_80MHZ | \
2171 WMI_VHT_CAP_TX_STBC | \
2172 WMI_VHT_CAP_RX_STBC_MASK | \
2173 WMI_VHT_CAP_MAX_AMPDU_LEN_EXP | \
2174 WMI_VHT_CAP_RX_FIXED_ANT | \
2175 WMI_VHT_CAP_TX_FIXED_ANT)
2177 /*
2178 * Interested readers refer to Rx/Tx MCS Map definition as defined in
2179 * 802.11ac
2180 */
2181 #define WMI_VHT_MAX_MCS_4_SS_MASK(r, ss) ((3 & (r)) << (((ss) - 1) << 1))
2182 #define WMI_VHT_MAX_SUPP_RATE_MASK 0x1fff0000
2183 #define WMI_VHT_MAX_SUPP_RATE_MASK_SHIFT 16
2209 };
2211 #define REGDMN_CAP1_CHAN_HALF_RATE 0x00000001
2212 #define REGDMN_CAP1_CHAN_QUARTER_RATE 0x00000002
2213 #define REGDMN_CAP1_CHAN_HAL49GHZ 0x00000004
2215 /* regulatory capabilities */
2216 #define REGDMN_EEPROM_EEREGCAP_EN_FCC_MIDBAND 0x0040
2217 #define REGDMN_EEPROM_EEREGCAP_EN_KK_U1_EVEN 0x0080
2218 #define REGDMN_EEPROM_EEREGCAP_EN_KK_U2 0x0100
2219 #define REGDMN_EEPROM_EEREGCAP_EN_KK_MIDBAND 0x0200
2220 #define REGDMN_EEPROM_EEREGCAP_EN_KK_U1_ODD 0x0400
2221 #define REGDMN_EEPROM_EEREGCAP_EN_KK_NEW_11A 0x0800
2224 /* regdomain value specified in EEPROM */
2225 __le32 eeprom_rd;
2226 /*regdomain */
2227 __le32 eeprom_rd_ext;
2228 /* CAP1 capabilities bit map. */
2229 __le32 regcap1;
2230 /* REGDMN EEPROM CAP. */
2231 __le32 regcap2;
2232 /* REGDMN MODE */
2233 __le32 wireless_modes;
2234 __le32 low_2ghz_chan;
2235 __le32 high_2ghz_chan;
2236 __le32 low_5ghz_chan;
2237 __le32 high_5ghz_chan;
2244 };
2246 /* structure used by FW for requesting host memory */
2248 /* ID of the request */
2249 __le32 req_id;
2250 /* size of the of each unit */
2251 __le32 unit_size;
2252 /* flags to indicate that
2253 * the number units is dependent
2254 * on number of resources(num vdevs num peers .. etc)
2255 */
2256 __le32 num_unit_info;
2257 /*
2258 * actual number of units to allocate . if flags in the num_unit_info
2259 * indicate that number of units is tied to number of a particular
2260 * resource to allocate then num_units filed is set to 0 and host
2261 * will derive the number units from number of the resources it is
2262 * requesting.
2263 */
2264 __le32 num_units;
2267 /*
2268 * The following struct holds optional payload for
2269 * wmi_service_ready_event,e.g., 11ac pass some of the
2270 * device capability to the host.
2271 */
2273 __le32 sw_version;
2274 __le32 sw_version_1;
2275 __le32 abi_version;
2276 /* WMI_PHY_CAPABILITY */
2277 __le32 phy_capability;
2278 /* Maximum number of frag table entries that SW will populate less 1 */
2279 __le32 max_frag_entry;
2281 __le32 num_rf_chains;
2282 /*
2283 * The following field is only valid for service type
2284 * WMI_SERVICE_11AC
2285 */
2289 __le32 hw_min_tx_power;
2290 __le32 hw_max_tx_power;
2292 __le32 sys_cap_info;
2294 /*
2295 * Max beacon and Probe Response IE offload size
2296 * (includes optional P2P IEs)
2297 */
2298 __le32 max_bcn_ie_size;
2299 /*
2300 * request to host to allocate a chuck of memory and pss it down to FW
2301 * via WM_INIT. FW uses this as FW extesnsion memory for saving its
2302 * data structures. Only valid for low latency interfaces like PCIE
2303 * where FW can access this memory directly (or) by DMA.
2304 */
2305 __le32 num_mem_reqs;
2309 /* This is the definition from 10.X firmware branch */
2311 __le32 sw_version;
2312 __le32 abi_version;
2314 /* WMI_PHY_CAPABILITY */
2315 __le32 phy_capability;
2317 /* Maximum number of frag table entries that SW will populate less 1 */
2318 __le32 max_frag_entry;
2320 __le32 num_rf_chains;
2322 /*
2323 * The following field is only valid for service type
2324 * WMI_SERVICE_11AC
2325 */
2329 __le32 hw_min_tx_power;
2330 __le32 hw_max_tx_power;
2334 __le32 sys_cap_info;
2337 /*
2338 * request to host to allocate a chuck of memory and pss it down to FW
2339 * via WM_INIT. FW uses this as FW extesnsion memory for saving its
2340 * data structures. Only valid for low latency interfaces like PCIE
2341 * where FW can access this memory directly (or) by DMA.
2342 */
2343 __le32 num_mem_reqs;
2348 #define WMI_SERVICE_READY_TIMEOUT_HZ (5 * HZ)
2349 #define WMI_UNIFIED_READY_TIMEOUT_HZ (5 * HZ)
2352 __le32 sw_version;
2353 __le32 abi_version;
2355 __le32 status;
2359 /* number of virtual devices (VAPs) to support */
2360 __le32 num_vdevs;
2362 /* number of peer nodes to support */
2363 __le32 num_peers;
2365 /*
2366 * In offload mode target supports features like WOW, chatter and
2367 * other protocol offloads. In order to support them some
2368 * functionalities like reorder buffering, PN checking need to be
2369 * done in target. This determines maximum number of peers supported
2370 * by target in offload mode
2371 */
2372 __le32 num_offload_peers;
2374 /* For target-based RX reordering */
2375 __le32 num_offload_reorder_bufs;
2377 /* number of keys per peer */
2378 __le32 num_peer_keys;
2380 /* total number of TX/RX data TIDs */
2381 __le32 num_tids;
2383 /*
2384 * max skid for resolving hash collisions
2385 *
2386 * The address search table is sparse, so that if two MAC addresses
2387 * result in the same hash value, the second of these conflicting
2388 * entries can slide to the next index in the address search table,
2389 * and use it, if it is unoccupied. This ast_skid_limit parameter
2390 * specifies the upper bound on how many subsequent indices to search
2391 * over to find an unoccupied space.
2392 */
2393 __le32 ast_skid_limit;
2395 /*
2396 * the nominal chain mask for transmit
2397 *
2398 * The chain mask may be modified dynamically, e.g. to operate AP
2399 * tx with a reduced number of chains if no clients are associated.
2400 * This configuration parameter specifies the nominal chain-mask that
2401 * should be used when not operating with a reduced set of tx chains.
2402 */
2403 __le32 tx_chain_mask;
2405 /*
2406 * the nominal chain mask for receive
2407 *
2408 * The chain mask may be modified dynamically, e.g. for a client
2409 * to use a reduced number of chains for receive if the traffic to
2410 * the client is low enough that it doesn't require downlink MIMO
2411 * or antenna diversity.
2412 * This configuration parameter specifies the nominal chain-mask that
2413 * should be used when not operating with a reduced set of rx chains.
2414 */
2415 __le32 rx_chain_mask;
2417 /*
2418 * what rx reorder timeout (ms) to use for the AC
2419 *
2420 * Each WMM access class (voice, video, best-effort, background) will
2421 * have its own timeout value to dictate how long to wait for missing
2422 * rx MPDUs to arrive before flushing subsequent MPDUs that have
2423 * already been received.
2424 * This parameter specifies the timeout in milliseconds for each
2425 * class.
2426 */
2427 __le32 rx_timeout_pri_vi;
2428 __le32 rx_timeout_pri_vo;
2429 __le32 rx_timeout_pri_be;
2430 __le32 rx_timeout_pri_bk;
2432 /*
2433 * what mode the rx should decap packets to
2434 *
2435 * MAC can decap to RAW (no decap), native wifi or Ethernet types
2436 * THis setting also determines the default TX behavior, however TX
2437 * behavior can be modified on a per VAP basis during VAP init
2438 */
2439 __le32 rx_decap_mode;
2441 /* what is the maximum number of scan requests that can be queued */
2442 __le32 scan_max_pending_reqs;
2444 /* maximum VDEV that could use BMISS offload */
2445 __le32 bmiss_offload_max_vdev;
2447 /* maximum VDEV that could use offload roaming */
2448 __le32 roam_offload_max_vdev;
2450 /* maximum AP profiles that would push to offload roaming */
2451 __le32 roam_offload_max_ap_profiles;
2453 /*
2454 * how many groups to use for mcast->ucast conversion
2455 *
2456 * The target's WAL maintains a table to hold information regarding
2457 * which peers belong to a given multicast group, so that if
2458 * multicast->unicast conversion is enabled, the target can convert
2459 * multicast tx frames to a series of unicast tx frames, to each
2460 * peer within the multicast group.
2461 This num_mcast_groups configuration parameter tells the target how
2462 * many multicast groups to provide storage for within its multicast
2463 * group membership table.
2464 */
2465 __le32 num_mcast_groups;
2467 /*
2468 * size to alloc for the mcast membership table
2469 *
2470 * This num_mcast_table_elems configuration parameter tells the
2471 * target how many peer elements it needs to provide storage for in
2472 * its multicast group membership table.
2473 * These multicast group membership table elements are shared by the
2474 * multicast groups stored within the table.
2475 */
2476 __le32 num_mcast_table_elems;
2478 /*
2479 * whether/how to do multicast->unicast conversion
2480 *
2481 * This configuration parameter specifies whether the target should
2482 * perform multicast --> unicast conversion on transmit, and if so,
2483 * what to do if it finds no entries in its multicast group
2484 * membership table for the multicast IP address in the tx frame.
2485 * Configuration value:
2486 * 0 -> Do not perform multicast to unicast conversion.
2487 * 1 -> Convert multicast frames to unicast, if the IP multicast
2488 * address from the tx frame is found in the multicast group
2489 * membership table. If the IP multicast address is not found,
2490 * drop the frame.
2491 * 2 -> Convert multicast frames to unicast, if the IP multicast
2492 * address from the tx frame is found in the multicast group
2493 * membership table. If the IP multicast address is not found,
2494 * transmit the frame as multicast.
2495 */
2496 __le32 mcast2ucast_mode;
2498 /*
2499 * how much memory to allocate for a tx PPDU dbg log
2500 *
2501 * This parameter controls how much memory the target will allocate
2502 * to store a log of tx PPDU meta-information (how large the PPDU
2503 * was, when it was sent, whether it was successful, etc.)
2504 */
2505 __le32 tx_dbg_log_size;
2507 /* how many AST entries to be allocated for WDS */
2508 __le32 num_wds_entries;
2510 /*
2511 * MAC DMA burst size, e.g., For target PCI limit can be
2512 * 0 -default, 1 256B
2513 */
2514 __le32 dma_burst_size;
2516 /*
2517 * Fixed delimiters to be inserted after every MPDU to
2518 * account for interface latency to avoid underrun.
2519 */
2520 __le32 mac_aggr_delim;
2522 /*
2523 * determine whether target is responsible for detecting duplicate
2524 * non-aggregate MPDU and timing out stale fragments.
2525 *
2526 * A-MPDU reordering is always performed on the target.
2527 *
2528 * 0: target responsible for frag timeout and dup checking
2529 * 1: host responsible for frag timeout and dup checking
2530 */
2531 __le32 rx_skip_defrag_timeout_dup_detection_check;
2533 /*
2534 * Configuration for VoW :
2535 * No of Video Nodes to be supported
2536 * and Max no of descriptors for each Video link (node).
2537 */
2538 __le32 vow_config;
2540 /* maximum VDEV that could use GTK offload */
2541 __le32 gtk_offload_max_vdev;
2543 /* Number of msdu descriptors target should use */
2544 __le32 num_msdu_desc;
2546 /*
2547 * Max. number of Tx fragments per MSDU
2548 * This parameter controls the max number of Tx fragments per MSDU.
2549 * This is sent by the target as part of the WMI_SERVICE_READY event
2550 * and is overridden by the OS shim as required.
2551 */
2552 __le32 max_frag_entries;
2556 /* number of virtual devices (VAPs) to support */
2557 __le32 num_vdevs;
2559 /* number of peer nodes to support */
2560 __le32 num_peers;
2562 /* number of keys per peer */
2563 __le32 num_peer_keys;
2565 /* total number of TX/RX data TIDs */
2566 __le32 num_tids;
2568 /*
2569 * max skid for resolving hash collisions
2570 *
2571 * The address search table is sparse, so that if two MAC addresses
2572 * result in the same hash value, the second of these conflicting
2573 * entries can slide to the next index in the address search table,
2574 * and use it, if it is unoccupied. This ast_skid_limit parameter
2575 * specifies the upper bound on how many subsequent indices to search
2576 * over to find an unoccupied space.
2577 */
2578 __le32 ast_skid_limit;
2580 /*
2581 * the nominal chain mask for transmit
2582 *
2583 * The chain mask may be modified dynamically, e.g. to operate AP
2584 * tx with a reduced number of chains if no clients are associated.
2585 * This configuration parameter specifies the nominal chain-mask that
2586 * should be used when not operating with a reduced set of tx chains.
2587 */
2588 __le32 tx_chain_mask;
2590 /*
2591 * the nominal chain mask for receive
2592 *
2593 * The chain mask may be modified dynamically, e.g. for a client
2594 * to use a reduced number of chains for receive if the traffic to
2595 * the client is low enough that it doesn't require downlink MIMO
2596 * or antenna diversity.
2597 * This configuration parameter specifies the nominal chain-mask that
2598 * should be used when not operating with a reduced set of rx chains.
2599 */
2600 __le32 rx_chain_mask;
2602 /*
2603 * what rx reorder timeout (ms) to use for the AC
2604 *
2605 * Each WMM access class (voice, video, best-effort, background) will
2606 * have its own timeout value to dictate how long to wait for missing
2607 * rx MPDUs to arrive before flushing subsequent MPDUs that have
2608 * already been received.
2609 * This parameter specifies the timeout in milliseconds for each
2610 * class.
2611 */
2612 __le32 rx_timeout_pri_vi;
2613 __le32 rx_timeout_pri_vo;
2614 __le32 rx_timeout_pri_be;
2615 __le32 rx_timeout_pri_bk;
2617 /*
2618 * what mode the rx should decap packets to
2619 *
2620 * MAC can decap to RAW (no decap), native wifi or Ethernet types
2621 * THis setting also determines the default TX behavior, however TX
2622 * behavior can be modified on a per VAP basis during VAP init
2623 */
2624 __le32 rx_decap_mode;
2626 /* what is the maximum number of scan requests that can be queued */
2627 __le32 scan_max_pending_reqs;
2629 /* maximum VDEV that could use BMISS offload */
2630 __le32 bmiss_offload_max_vdev;
2632 /* maximum VDEV that could use offload roaming */
2633 __le32 roam_offload_max_vdev;
2635 /* maximum AP profiles that would push to offload roaming */
2636 __le32 roam_offload_max_ap_profiles;
2638 /*
2639 * how many groups to use for mcast->ucast conversion
2640 *
2641 * The target's WAL maintains a table to hold information regarding
2642 * which peers belong to a given multicast group, so that if
2643 * multicast->unicast conversion is enabled, the target can convert
2644 * multicast tx frames to a series of unicast tx frames, to each
2645 * peer within the multicast group.
2646 This num_mcast_groups configuration parameter tells the target how
2647 * many multicast groups to provide storage for within its multicast
2648 * group membership table.
2649 */
2650 __le32 num_mcast_groups;
2652 /*
2653 * size to alloc for the mcast membership table
2654 *
2655 * This num_mcast_table_elems configuration parameter tells the
2656 * target how many peer elements it needs to provide storage for in
2657 * its multicast group membership table.
2658 * These multicast group membership table elements are shared by the
2659 * multicast groups stored within the table.
2660 */
2661 __le32 num_mcast_table_elems;
2663 /*
2664 * whether/how to do multicast->unicast conversion
2665 *
2666 * This configuration parameter specifies whether the target should
2667 * perform multicast --> unicast conversion on transmit, and if so,
2668 * what to do if it finds no entries in its multicast group
2669 * membership table for the multicast IP address in the tx frame.
2670 * Configuration value:
2671 * 0 -> Do not perform multicast to unicast conversion.
2672 * 1 -> Convert multicast frames to unicast, if the IP multicast
2673 * address from the tx frame is found in the multicast group
2674 * membership table. If the IP multicast address is not found,
2675 * drop the frame.
2676 * 2 -> Convert multicast frames to unicast, if the IP multicast
2677 * address from the tx frame is found in the multicast group
2678 * membership table. If the IP multicast address is not found,
2679 * transmit the frame as multicast.
2680 */
2681 __le32 mcast2ucast_mode;
2683 /*
2684 * how much memory to allocate for a tx PPDU dbg log
2685 *
2686 * This parameter controls how much memory the target will allocate
2687 * to store a log of tx PPDU meta-information (how large the PPDU
2688 * was, when it was sent, whether it was successful, etc.)
2689 */
2690 __le32 tx_dbg_log_size;
2692 /* how many AST entries to be allocated for WDS */
2693 __le32 num_wds_entries;
2695 /*
2696 * MAC DMA burst size, e.g., For target PCI limit can be
2697 * 0 -default, 1 256B
2698 */
2699 __le32 dma_burst_size;
2701 /*
2702 * Fixed delimiters to be inserted after every MPDU to
2703 * account for interface latency to avoid underrun.
2704 */
2705 __le32 mac_aggr_delim;
2707 /*
2708 * determine whether target is responsible for detecting duplicate
2709 * non-aggregate MPDU and timing out stale fragments.
2710 *
2711 * A-MPDU reordering is always performed on the target.
2712 *
2713 * 0: target responsible for frag timeout and dup checking
2714 * 1: host responsible for frag timeout and dup checking
2715 */
2716 __le32 rx_skip_defrag_timeout_dup_detection_check;
2718 /*
2719 * Configuration for VoW :
2720 * No of Video Nodes to be supported
2721 * and Max no of descriptors for each Video link (node).
2722 */
2723 __le32 vow_config;
2725 /* Number of msdu descriptors target should use */
2726 __le32 num_msdu_desc;
2728 /*
2729 * Max. number of Tx fragments per MSDU
2730 * This parameter controls the max number of Tx fragments per MSDU.
2731 * This is sent by the target as part of the WMI_SERVICE_READY event
2732 * and is overridden by the OS shim as required.
2733 */
2734 __le32 max_frag_entries;
2743 };
2747 __le32 max_peer_ext_stats;
2749 __le32 bk_min_free;
2750 __le32 be_min_free;
2751 __le32 vi_min_free;
2752 __le32 vo_min_free;
2753 __le32 feature_mask;
2756 #define NUM_UNITS_IS_NUM_VDEVS BIT(0)
2757 #define NUM_UNITS_IS_NUM_PEERS BIT(1)
2758 #define NUM_UNITS_IS_NUM_ACTIVE_PEERS BIT(2)
2761 /* Number of virtual devices (VAPs) to support */
2762 __le32 num_vdevs;
2764 /* Number of peer nodes to support */
2765 __le32 num_peers;
2767 /* Number of active peer nodes to support */
2768 __le32 num_active_peers;
2770 /* In offload mode, target supports features like WOW, chatter and other
2771 * protocol offloads. In order to support them some functionalities like
2772 * reorder buffering, PN checking need to be done in target.
2773 * This determines maximum number of peers supported by target in
2774 * offload mode.
2775 */
2776 __le32 num_offload_peers;
2778 /* Number of reorder buffers available for doing target based reorder
2779 * Rx reorder buffering
2780 */
2781 __le32 num_offload_reorder_buffs;
2783 /* Number of keys per peer */
2784 __le32 num_peer_keys;
2786 /* Total number of TX/RX data TIDs */
2787 __le32 num_tids;
2789 /* Max skid for resolving hash collisions.
2790 * The address search table is sparse, so that if two MAC addresses
2791 * result in the same hash value, the second of these conflicting
2792 * entries can slide to the next index in the address search table,
2793 * and use it, if it is unoccupied. This ast_skid_limit parameter
2794 * specifies the upper bound on how many subsequent indices to search
2795 * over to find an unoccupied space.
2796 */
2797 __le32 ast_skid_limit;
2799 /* The nominal chain mask for transmit.
2800 * The chain mask may be modified dynamically, e.g. to operate AP tx
2801 * with a reduced number of chains if no clients are associated.
2802 * This configuration parameter specifies the nominal chain-mask that
2803 * should be used when not operating with a reduced set of tx chains.
2804 */
2805 __le32 tx_chain_mask;
2807 /* The nominal chain mask for receive.
2808 * The chain mask may be modified dynamically, e.g. for a client to use
2809 * a reduced number of chains for receive if the traffic to the client
2810 * is low enough that it doesn't require downlink MIMO or antenna
2811 * diversity. This configuration parameter specifies the nominal
2812 * chain-mask that should be used when not operating with a reduced
2813 * set of rx chains.
2814 */
2815 __le32 rx_chain_mask;
2817 /* What rx reorder timeout (ms) to use for the AC.
2818 * Each WMM access class (voice, video, best-effort, background) will
2819 * have its own timeout value to dictate how long to wait for missing
2820 * rx MPDUs to arrive before flushing subsequent MPDUs that have already
2821 * been received. This parameter specifies the timeout in milliseconds
2822 * for each class.
2823 */
2826 /* What mode the rx should decap packets to.
2827 * MAC can decap to RAW (no decap), native wifi or Ethernet types.
2828 * This setting also determines the default TX behavior, however TX
2829 * behavior can be modified on a per VAP basis during VAP init
2830 */
2831 __le32 rx_decap_mode;
2833 __le32 scan_max_pending_req;
2835 __le32 bmiss_offload_max_vdev;
2837 __le32 roam_offload_max_vdev;
2839 __le32 roam_offload_max_ap_profiles;
2841 /* How many groups to use for mcast->ucast conversion.
2842 * The target's WAL maintains a table to hold information regarding
2843 * which peers belong to a given multicast group, so that if
2844 * multicast->unicast conversion is enabled, the target can convert
2845 * multicast tx frames to a series of unicast tx frames, to each peer
2846 * within the multicast group. This num_mcast_groups configuration
2847 * parameter tells the target how many multicast groups to provide
2848 * storage for within its multicast group membership table.
2849 */
2850 __le32 num_mcast_groups;
2852 /* Size to alloc for the mcast membership table.
2853 * This num_mcast_table_elems configuration parameter tells the target
2854 * how many peer elements it needs to provide storage for in its
2855 * multicast group membership table. These multicast group membership
2856 * table elements are shared by the multicast groups stored within
2857 * the table.
2858 */
2859 __le32 num_mcast_table_elems;
2861 /* Whether/how to do multicast->unicast conversion.
2862 * This configuration parameter specifies whether the target should
2863 * perform multicast --> unicast conversion on transmit, and if so,
2864 * what to do if it finds no entries in its multicast group membership
2865 * table for the multicast IP address in the tx frame.
2866 * Configuration value:
2867 * 0 -> Do not perform multicast to unicast conversion.
2868 * 1 -> Convert multicast frames to unicast, if the IP multicast address
2869 * from the tx frame is found in the multicast group membership
2870 * table. If the IP multicast address is not found, drop the frame
2871 * 2 -> Convert multicast frames to unicast, if the IP multicast address
2872 * from the tx frame is found in the multicast group membership
2873 * table. If the IP multicast address is not found, transmit the
2874 * frame as multicast.
2875 */
2876 __le32 mcast2ucast_mode;
2878 /* How much memory to allocate for a tx PPDU dbg log.
2879 * This parameter controls how much memory the target will allocate to
2880 * store a log of tx PPDU meta-information (how large the PPDU was,
2881 * when it was sent, whether it was successful, etc.)
2882 */
2883 __le32 tx_dbg_log_size;
2885 /* How many AST entries to be allocated for WDS */
2886 __le32 num_wds_entries;
2888 /* MAC DMA burst size. 0 -default, 1 -256B */
2889 __le32 dma_burst_size;
2891 /* Fixed delimiters to be inserted after every MPDU to account for
2892 * interface latency to avoid underrun.
2893 */
2894 __le32 mac_aggr_delim;
2896 /* Determine whether target is responsible for detecting duplicate
2897 * non-aggregate MPDU and timing out stale fragments. A-MPDU reordering
2898 * is always performed on the target.
2899 *
2900 * 0: target responsible for frag timeout and dup checking
2901 * 1: host responsible for frag timeout and dup checking
2902 */
2903 __le32 rx_skip_defrag_timeout_dup_detection_check;
2905 /* Configuration for VoW : No of Video nodes to be supported and max
2906 * no of descriptors for each video link (node).
2907 */
2908 __le32 vow_config;
2910 /* Maximum vdev that could use gtk offload */
2911 __le32 gtk_offload_max_vdev;
2913 /* Number of msdu descriptors target should use */
2914 __le32 num_msdu_desc;
2916 /* Max number of tx fragments per MSDU.
2917 * This parameter controls the max number of tx fragments per MSDU.
2918 * This will passed by target as part of the WMI_SERVICE_READY event
2919 * and is overridden by the OS shim as required.
2920 */
2921 __le32 max_frag_entries;
2923 /* Max number of extended peer stats.
2924 * This parameter controls the max number of peers for which extended
2925 * statistics are supported by target
2926 */
2927 __le32 max_peer_ext_stats;
2929 /* Smart antenna capabilities information.
2930 * 1 - Smart antenna is enabled
2931 * 0 - Smart antenna is disabled
2932 * In future this can contain smart antenna specific capabilities.
2933 */
2934 __le32 smart_ant_cap;
2936 /* User can configure the buffers allocated for each AC (BE, BK, VI, VO)
2937 * during init.
2938 */
2939 __le32 bk_minfree;
2940 __le32 be_minfree;
2941 __le32 vi_minfree;
2942 __le32 vo_minfree;
2944 /* Rx batch mode capability.
2945 * 1 - Rx batch mode enabled
2946 * 0 - Rx batch mode disabled
2947 */
2948 __le32 rx_batchmode;
2950 /* Thermal throttling capability.
2951 * 1 - Capable of thermal throttling
2952 * 0 - Not capable of thermal throttling
2953 */
2954 __le32 tt_support;
2956 /* ATF configuration.
2957 * 1 - Enable ATF
2958 * 0 - Disable ATF
2959 */
2960 __le32 atf_config;
2962 /* Configure padding to manage IP header un-alignment
2963 * 1 - Enable padding
2964 * 0 - Disable padding
2965 */
2966 __le32 iphdr_pad_config;
2968 /* qwrap configuration (bits 15-0)
2969 * 1 - This is qwrap configuration
2970 * 0 - This is not qwrap
2971 *
2972 * Bits 31-16 is alloc_frag_desc_for_data_pkt (1 enables, 0 disables)
2973 * In order to get ack-RSSI reporting and to specify the tx-rate for
2974 * individual frames, this option must be enabled. This uses an extra
2975 * 4 bytes per tx-msdu descriptor, so don't enable it unless you need it.
2976 */
2977 __le32 qwrap_config;
2982 /* 3 wire coex support*/
2984 /* 2.5 wire coex support*/
2986 /* 2.5 wire coex with duty cycle support */
2988 /* 4 wire coex support*/
2990 };
2992 /**
2993 * enum wmi_10_4_feature_mask - WMI 10.4 feature enable/disable flags
2994 * @WMI_10_4_LTEU_SUPPORT: LTEU config
2995 * @WMI_10_4_COEX_GPIO_SUPPORT: COEX GPIO config
2996 * @WMI_10_4_AUX_RADIO_SPECTRAL_INTF: AUX Radio Enhancement for spectral scan
2997 * @WMI_10_4_AUX_RADIO_CHAN_LOAD_INTF: AUX Radio Enhancement for chan load scan
2998 * @WMI_10_4_BSS_CHANNEL_INFO_64: BSS channel info stats
2999 * @WMI_10_4_PEER_STATS: Per station stats
3000 * @WMI_10_4_VDEV_STATS: Per vdev stats
3001 * @WMI_10_4_TDLS: Implicit TDLS support in firmware enable/disable
3002 * @WMI_10_4_TDLS_OFFCHAN: TDLS offchannel support enable/disable
3003 * @WMI_10_4_TDLS_UAPSD_BUFFER_STA: TDLS buffer sta support enable/disable
3004 * @WMI_10_4_TDLS_UAPSD_SLEEP_STA: TDLS sleep sta support enable/disable
3005 * @WMI_10_4_TDLS_CONN_TRACKER_IN_HOST_MODE: TDLS connection tracker in host
3006 * enable/disable
3007 * @WMI_10_4_TDLS_EXPLICIT_MODE_ONLY:Explicit TDLS mode enable/disable
3008 * @WMI_10_4_TX_DATA_ACK_RSSI: Enable DATA ACK RSSI if firmware is capable
3009 */
3028 };
3031 /* contains enum wmi_host_platform_type */
3032 __le32 host_platform_config;
3033 /* see enum wmi_10_4_feature_mask */
3034 __le32 fw_feature_bitmap;
3035 /* WLAN priority GPIO number */
3036 __le32 wlan_gpio_priority;
3037 /* see enum wmi_coex_version */
3038 __le32 coex_version;
3039 /* COEX GPIO config */
3040 __le32 coex_gpio_pin1;
3041 __le32 coex_gpio_pin2;
3042 __le32 coex_gpio_pin3;
3043 /* number of vdevs allowed to perform tdls */
3044 __le32 num_tdls_vdevs;
3045 /* number of peers to track per TDLS vdev */
3046 __le32 num_tdls_conn_table_entries;
3047 /* number of tdls sleep sta supported */
3048 __le32 max_tdls_concurrent_sleep_sta;
3049 /* number of tdls buffer sta supported */
3050 __le32 max_tdls_concurrent_buffer_sta;
3051 };
3053 /* structure describing host memory chunk. */
3055 /* id of the request that is passed up in service ready */
3056 __le32 req_id;
3057 /* the physical address the memory chunk */
3058 __le32 ptr;
3059 /* size of the chunk */
3060 __le32 size;
3063 #define WMI_IRAM_RECOVERY_HOST_MEM_REQ_ID 8
3066 __le32 count;
3067 /* some fw revisions require at least 1 chunk regardless of count */
3076 /* _10x structure is from 10.X FW API */
3093 __le16 freq;
3095 u8 reserved;
3098 /* TLV for channel list */
3101 __le32 num_chan;
3107 __le32 num_bssid;
3113 __le32 ie_len;
3114 u8 ie_data[];
3118 __le32 ssid_len;
3124 __le32 num_ssids;
3128 /* prefix used by scan requestor ids on the host */
3129 #define WMI_HOST_SCAN_REQUESTOR_ID_PREFIX 0xA000
3131 /* prefix used by scan request ids generated on the host */
3132 /* host cycles through the lower 12 bits to generate ids */
3133 #define WMI_HOST_SCAN_REQ_ID_PREFIX 0xA000
3135 #define WLAN_SCAN_PARAMS_MAX_SSID 16
3136 #define WLAN_SCAN_PARAMS_MAX_BSSID 4
3137 #define WLAN_SCAN_PARAMS_MAX_IE_LEN 256
3139 /* Values lower than this may be refused by some firmware revisions with a scan
3140 * completion with a timedout reason.
3141 */
3142 #define WMI_SCAN_CHAN_MIN_TIME_MSEC 40
3144 /* Scan priority numbers must be sequential, starting with 0 */
3147 WMI_SCAN_PRIORITY_LOW,
3148 WMI_SCAN_PRIORITY_MEDIUM,
3149 WMI_SCAN_PRIORITY_HIGH,
3150 WMI_SCAN_PRIORITY_VERY_HIGH,
3151 WMI_SCAN_PRIORITY_COUNT /* number of priorities supported */
3152 };
3155 /* Scan ID */
3156 __le32 scan_id;
3157 /* Scan requestor ID */
3158 __le32 scan_req_id;
3159 /* VDEV id(interface) that is requesting scan */
3160 __le32 vdev_id;
3161 /* Scan Priority, input to scan scheduler */
3162 __le32 scan_priority;
3163 /* Scan events subscription */
3164 __le32 notify_scan_events;
3165 /* dwell time in msec on active channels */
3166 __le32 dwell_time_active;
3167 /* dwell time in msec on passive channels */
3168 __le32 dwell_time_passive;
3169 /*
3170 * min time in msec on the BSS channel,only valid if atleast one
3171 * VDEV is active
3172 */
3173 __le32 min_rest_time;
3174 /*
3175 * max rest time in msec on the BSS channel,only valid if at least
3176 * one VDEV is active
3177 */
3178 /*
3179 * the scanner will rest on the bss channel at least min_rest_time
3180 * after min_rest_time the scanner will start checking for tx/rx
3181 * activity on all VDEVs. if there is no activity the scanner will
3182 * switch to off channel. if there is activity the scanner will let
3183 * the radio on the bss channel until max_rest_time expires.at
3184 * max_rest_time scanner will switch to off channel irrespective of
3185 * activity. activity is determined by the idle_time parameter.
3186 */
3187 __le32 max_rest_time;
3188 /*
3189 * time before sending next set of probe requests.
3190 * The scanner keeps repeating probe requests transmission with
3191 * period specified by repeat_probe_time.
3192 * The number of probe requests specified depends on the ssid_list
3193 * and bssid_list
3194 */
3195 __le32 repeat_probe_time;
3196 /* time in msec between 2 consequetive probe requests with in a set. */
3197 __le32 probe_spacing_time;
3198 /*
3199 * data inactivity time in msec on bss channel that will be used by
3200 * scanner for measuring the inactivity.
3201 */
3202 __le32 idle_time;
3203 /* maximum time in msec allowed for scan */
3204 __le32 max_scan_time;
3205 /*
3206 * delay in msec before sending first probe request after switching
3207 * to a channel
3208 */
3209 __le32 probe_delay;
3210 /* Scan control flags */
3211 __le32 scan_ctrl_flags;
3215 /* TLV parameters. These includes channel list, ssid list, bssid list,
3216 * extra ies.
3217 */
3223 __le32 burst_duration_ms;
3227 /* This is the definition from 10.X firmware branch */
3236 };
3240 };
3243 u32 scan_id;
3244 u32 scan_req_id;
3245 u32 vdev_id;
3246 u32 scan_priority;
3247 u32 notify_scan_events;
3248 u32 dwell_time_active;
3249 u32 dwell_time_passive;
3250 u32 min_rest_time;
3251 u32 max_rest_time;
3252 u32 repeat_probe_time;
3253 u32 probe_spacing_time;
3254 u32 idle_time;
3255 u32 max_scan_time;
3256 u32 probe_delay;
3257 u32 scan_ctrl_flags;
3258 u32 burst_duration_ms;
3260 u32 ie_len;
3261 u32 n_channels;
3262 u32 n_ssids;
3263 u32 n_bssids;
3271 };
3273 /* scan control flags */
3275 /* passively scan all channels including active channels */
3276 #define WMI_SCAN_FLAG_PASSIVE 0x1
3277 /* add wild card ssid probe request even though ssid_list is specified. */
3278 #define WMI_SCAN_ADD_BCAST_PROBE_REQ 0x2
3279 /* add cck rates to rates/xrate ie for the generated probe request */
3280 #define WMI_SCAN_ADD_CCK_RATES 0x4
3281 /* add ofdm rates to rates/xrate ie for the generated probe request */
3282 #define WMI_SCAN_ADD_OFDM_RATES 0x8
3283 /* To enable indication of Chan load and Noise floor to host */
3284 #define WMI_SCAN_CHAN_STAT_EVENT 0x10
3285 /* Filter Probe request frames */
3286 #define WMI_SCAN_FILTER_PROBE_REQ 0x20
3287 /* When set, DFS channels will not be scanned */
3288 #define WMI_SCAN_BYPASS_DFS_CHN 0x40
3289 /* Different FW scan engine may choose to bail out on errors.
3290 * Allow the driver to have influence over that.
3291 */
3292 #define WMI_SCAN_CONTINUE_ON_ERROR 0x80
3294 /* Use random MAC address for TA for Probe Request frame and add
3295 * OUI specified by WMI_SCAN_PROB_REQ_OUI_CMDID to the Probe Request frame.
3296 * if OUI is not set by WMI_SCAN_PROB_REQ_OUI_CMDID then the flag is ignored.
3297 */
3298 #define WMI_SCAN_ADD_SPOOFED_MAC_IN_PROBE_REQ 0x1000
3300 /* WMI_SCAN_CLASS_MASK must be the same value as IEEE80211_SCAN_CLASS_MASK */
3301 #define WMI_SCAN_CLASS_MASK 0xFF000000
3307 };
3310 __le32 scan_req_id;
3311 __le32 scan_id;
3312 __le32 req_type;
3313 __le32 vdev_id;
3317 u32 req_id;
3320 u32 scan_id;
3321 u32 vdev_id;
3323 };
3326 __le32 num_scan_chans;
3331 u32 n_channels;
3333 };
3344 };
3352 /* possibly by high-prio scan */
3358 };
3361 WMI_SCAN_REASON_COMPLETED,
3362 WMI_SCAN_REASON_CANCELLED,
3363 WMI_SCAN_REASON_PREEMPTED,
3364 WMI_SCAN_REASON_TIMEDOUT,
3365 WMI_SCAN_REASON_INTERNAL_FAILURE,
3366 WMI_SCAN_REASON_MAX,
3367 };
3373 __le32 scan_req_id;
3374 __le32 scan_id;
3375 __le32 vdev_id;
3378 /*
3379 * This defines how much headroom is kept in the
3380 * receive frame between the descriptor and the
3381 * payload, in order for the WMI PHY error and
3382 * management handler to insert header contents.
3383 *
3384 * This is in bytes.
3385 */
3386 #define WMI_MGMT_RX_HDR_HEADROOM 52
3388 /*
3389 * This event will be used for sending scan results
3390 * as well as rx mgmt frames to the host. The rx buffer
3391 * will be sent as part of this WMI event. It would be a
3392 * good idea to pass all the fields in the RX status
3393 * descriptor up to the host.
3394 */
3396 __le32 channel;
3397 __le32 snr;
3398 __le32 rate;
3399 __le32 phy_mode;
3400 __le32 buf_len;
3411 u8 buf[];
3416 u8 buf[];
3420 __le32 channel;
3421 __le32 snr;
3423 __le32 rate;
3424 __le32 phy_mode;
3425 __le32 buf_len;
3426 __le32 status;
3431 u8 buf[];
3435 __le64 rx_mac_timestamp;
3438 #define WMI_RX_STATUS_OK 0x00
3439 #define WMI_RX_STATUS_ERR_CRC 0x01
3440 #define WMI_RX_STATUS_ERR_DECRYPT 0x08
3441 #define WMI_RX_STATUS_ERR_MIC 0x10
3442 #define WMI_RX_STATUS_ERR_KEY_CACHE_MISS 0x20
3443 /* Extension data at the end of mgmt frame */
3444 #define WMI_RX_STATUS_EXT_INFO 0x40
3446 #define PHY_ERROR_GEN_SPECTRAL_SCAN 0x26
3447 #define PHY_ERROR_GEN_FALSE_RADAR_EXT 0x24
3448 #define PHY_ERROR_GEN_RADAR 0x05
3450 #define PHY_ERROR_10_4_RADAR_MASK 0x4
3451 #define PHY_ERROR_10_4_SPECTRAL_SCAN_MASK 0x4000000
3454 PHY_ERROR_UNKNOWN,
3455 PHY_ERROR_SPECTRAL_SCAN,
3456 PHY_ERROR_FALSE_RADAR_EXT,
3457 PHY_ERROR_RADAR
3458 };
3461 __le32 tsf_timestamp;
3462 __le16 freq1;
3463 __le16 freq2;
3464 u8 rssi_combined;
3465 u8 chan_width_mhz;
3466 u8 phy_err_code;
3467 u8 rsvd0;
3470 __le32 buf_len;
3471 u8 buf[];
3475 __le32 num_phyerrs;
3476 __le32 tsf_l32;
3477 __le32 tsf_u32;
3482 __le32 tsf_l32;
3483 __le32 tsf_u32;
3484 __le16 freq1;
3485 __le16 freq2;
3486 u8 rssi_combined;
3487 u8 chan_width_mhz;
3488 u8 phy_err_code;
3489 u8 rsvd0;
3493 __le32 tsf_timestamp;
3494 __le32 buf_len;
3495 u8 buf[];
3499 __le32 pri_min;
3500 __le32 pri_max;
3501 __le32 width_min;
3502 __le32 width_max;
3503 __le32 sidx_min;
3504 __le32 sidx_max;
3508 /* Detected radar was due to SW pulses */
3513 /* Real radar detected */
3515 };
3517 #define PHYERR_TLV_SIG 0xBB
3518 #define PHYERR_TLV_TAG_SEARCH_FFT_REPORT 0xFB
3519 #define PHYERR_TLV_TAG_RADAR_PULSE_SUMMARY 0xF8
3520 #define PHYERR_TLV_TAG_SPECTRAL_SUMMARY_REPORT 0xF9
3527 #define RADAR_REPORT_REG0_PULSE_IS_CHIRP_MASK 0x80000000
3528 #define RADAR_REPORT_REG0_PULSE_IS_CHIRP_LSB 31
3530 #define RADAR_REPORT_REG0_PULSE_IS_MAX_WIDTH_MASK 0x40000000
3531 #define RADAR_REPORT_REG0_PULSE_IS_MAX_WIDTH_LSB 30
3533 #define RADAR_REPORT_REG0_AGC_TOTAL_GAIN_MASK 0x3FF00000
3534 #define RADAR_REPORT_REG0_AGC_TOTAL_GAIN_LSB 20
3536 #define RADAR_REPORT_REG0_PULSE_DELTA_DIFF_MASK 0x000F0000
3537 #define RADAR_REPORT_REG0_PULSE_DELTA_DIFF_LSB 16
3539 #define RADAR_REPORT_REG0_PULSE_DELTA_PEAK_MASK 0x0000FC00
3540 #define RADAR_REPORT_REG0_PULSE_DELTA_PEAK_LSB 10
3542 #define RADAR_REPORT_REG0_PULSE_SIDX_MASK 0x000003FF
3543 #define RADAR_REPORT_REG0_PULSE_SIDX_LSB 0
3545 #define RADAR_REPORT_REG1_PULSE_SRCH_FFT_VALID_MASK 0x80000000
3546 #define RADAR_REPORT_REG1_PULSE_SRCH_FFT_VALID_LSB 31
3548 #define RADAR_REPORT_REG1_PULSE_AGC_MB_GAIN_MASK 0x7F000000
3549 #define RADAR_REPORT_REG1_PULSE_AGC_MB_GAIN_LSB 24
3551 #define RADAR_REPORT_REG1_PULSE_SUBCHAN_MASK_MASK 0x00FF0000
3552 #define RADAR_REPORT_REG1_PULSE_SUBCHAN_MASK_LSB 16
3554 #define RADAR_REPORT_REG1_PULSE_TSF_OFFSET_MASK 0x0000FF00
3555 #define RADAR_REPORT_REG1_PULSE_TSF_OFFSET_LSB 8
3557 #define RADAR_REPORT_REG1_PULSE_DUR_MASK 0x000000FF
3558 #define RADAR_REPORT_REG1_PULSE_DUR_LSB 0
3565 #define SEARCH_FFT_REPORT_REG0_TOTAL_GAIN_DB_MASK 0xFF800000
3566 #define SEARCH_FFT_REPORT_REG0_TOTAL_GAIN_DB_LSB 23
3568 #define SEARCH_FFT_REPORT_REG0_BASE_PWR_DB_MASK 0x007FC000
3569 #define SEARCH_FFT_REPORT_REG0_BASE_PWR_DB_LSB 14
3571 #define SEARCH_FFT_REPORT_REG0_FFT_CHN_IDX_MASK 0x00003000
3572 #define SEARCH_FFT_REPORT_REG0_FFT_CHN_IDX_LSB 12
3574 #define SEARCH_FFT_REPORT_REG0_PEAK_SIDX_MASK 0x00000FFF
3575 #define SEARCH_FFT_REPORT_REG0_PEAK_SIDX_LSB 0
3577 #define SEARCH_FFT_REPORT_REG1_RELPWR_DB_MASK 0xFC000000
3578 #define SEARCH_FFT_REPORT_REG1_RELPWR_DB_LSB 26
3580 #define SEARCH_FFT_REPORT_REG1_AVGPWR_DB_MASK 0x03FC0000
3581 #define SEARCH_FFT_REPORT_REG1_AVGPWR_DB_LSB 18
3583 #define SEARCH_FFT_REPORT_REG1_PEAK_MAG_MASK 0x0003FF00
3584 #define SEARCH_FFT_REPORT_REG1_PEAK_MAG_LSB 8
3586 #define SEARCH_FFT_REPORT_REG1_NUM_STR_BINS_IB_MASK 0x000000FF
3587 #define SEARCH_FFT_REPORT_REG1_NUM_STR_BINS_IB_LSB 0
3590 __le16 len;
3591 u8 tag;
3592 u8 sig;
3595 #define DFS_RSSI_POSSIBLY_FALSE 50
3596 #define DFS_PEAK_MAG_THOLD_POSSIBLY_FALSE 40
3599 __le32 vdev_id;
3601 __le32 tx_rate;
3602 __le32 tx_power;
3603 __le32 buf_len;
3608 u8 buf[];
3612 __le32 value;
3616 __le32 value;
3620 __le32 reg_domain;
3621 __le32 reg_domain_2G;
3622 __le32 reg_domain_5G;
3623 __le32 conformance_test_limit_2G;
3624 __le32 conformance_test_limit_5G;
3628 /* Uninitialized dfs domain */
3631 /* FCC3 dfs domain */
3634 /* ETSI dfs domain */
3637 /*Japan dfs domain */
3639 };
3642 __le32 reg_domain;
3643 __le32 reg_domain_2G;
3644 __le32 reg_domain_5G;
3645 __le32 conformance_test_limit_2G;
3646 __le32 conformance_test_limit_5G;
3648 /* dfs domain from wmi_dfs_region */
3649 __le32 dfs_domain;
3652 /* Command to set/unset chip in quiet mode */
3654 /* period in TUs */
3655 __le32 period;
3657 /* duration in TUs */
3658 __le32 duration;
3660 /* offset in TUs */
3661 __le32 next_start;
3663 /* enable/disable */
3664 __le32 enabled;
3667 /*
3668 * 802.11g protection mode.
3669 */
3674 };
3678 WMI_RTSCTS_FOR_SECOND_RATESERIES,
3679 WMI_RTSCTS_ACROSS_SW_RETRIES
3680 };
3682 #define WMI_RTSCTS_ENABLED 1
3683 #define WMI_RTSCTS_SET_MASK 0x0f
3684 #define WMI_RTSCTS_SET_LSB 0
3686 #define WMI_RTSCTS_PROFILE_MASK 0xf0
3687 #define WMI_RTSCTS_PROFILE_LSB 4
3692 };
3699 };
3701 /* wmi CSA receive event from beacon frame */
3703 __le32 i_fc_dur;
3704 /* Bit 0-15: FC */
3705 /* Bit 16-31: DUR */
3711 __le32 cswarp_ie;
3715 /* the definition of different PDEV parameters */
3716 #define PDEV_DEFAULT_STATS_UPDATE_PERIOD 500
3717 #define VDEV_DEFAULT_STATS_UPDATE_PERIOD 500
3718 #define PEER_DEFAULT_STATS_UPDATE_PERIOD 500
3721 u32 tx_chain_mask;
3722 u32 rx_chain_mask;
3723 u32 txpower_limit2g;
3724 u32 txpower_limit5g;
3725 u32 txpower_scale;
3726 u32 beacon_gen_mode;
3727 u32 beacon_tx_mode;
3728 u32 resmgr_offchan_mode;
3729 u32 protection_mode;
3730 u32 dynamic_bw;
3731 u32 non_agg_sw_retry_th;
3732 u32 agg_sw_retry_th;
3733 u32 sta_kickout_th;
3734 u32 ac_aggrsize_scaling;
3735 u32 ltr_enable;
3736 u32 ltr_ac_latency_be;
3737 u32 ltr_ac_latency_bk;
3738 u32 ltr_ac_latency_vi;
3739 u32 ltr_ac_latency_vo;
3740 u32 ltr_ac_latency_timeout;
3741 u32 ltr_sleep_override;
3742 u32 ltr_rx_override;
3743 u32 ltr_tx_activity_timeout;
3744 u32 l1ss_enable;
3745 u32 dsleep_enable;
3746 u32 pcielp_txbuf_flush;
3747 u32 pcielp_txbuf_watermark;
3748 u32 pcielp_txbuf_tmo_en;
3749 u32 pcielp_txbuf_tmo_value;
3750 u32 pdev_stats_update_period;
3751 u32 vdev_stats_update_period;
3752 u32 peer_stats_update_period;
3753 u32 bcnflt_stats_update_period;
3754 u32 pmf_qos;
3755 u32 arp_ac_override;
3756 u32 dcs;
3757 u32 ani_enable;
3758 u32 ani_poll_period;
3759 u32 ani_listen_period;
3760 u32 ani_ofdm_level;
3761 u32 ani_cck_level;
3762 u32 dyntxchain;
3763 u32 proxy_sta;
3764 u32 idle_ps_config;
3765 u32 power_gating_sleep;
3766 u32 fast_channel_reset;
3767 u32 burst_dur;
3768 u32 burst_enable;
3769 u32 cal_period;
3770 u32 aggr_burst;
3771 u32 rx_decap_mode;
3772 u32 smart_antenna_default_antenna;
3773 u32 igmpmld_override;
3774 u32 igmpmld_tid;
3775 u32 antenna_gain;
3776 u32 rx_filter;
3777 u32 set_mcast_to_ucast_tid;
3778 u32 proxy_sta_mode;
3779 u32 set_mcast2ucast_mode;
3780 u32 set_mcast2ucast_buffer;
3781 u32 remove_mcast2ucast_buffer;
3782 u32 peer_sta_ps_statechg_enable;
3783 u32 igmpmld_ac_override;
3784 u32 block_interbss;
3785 u32 set_disable_reset_cmdid;
3786 u32 set_msdu_ttl_cmdid;
3787 u32 set_ppdu_duration_cmdid;
3788 u32 txbf_sound_period_cmdid;
3789 u32 set_promisc_mode_cmdid;
3790 u32 set_burst_mode_cmdid;
3791 u32 en_stats;
3792 u32 mu_group_policy;
3793 u32 noise_detection;
3794 u32 noise_threshold;
3795 u32 dpd_enable;
3796 u32 set_mcast_bcast_echo;
3797 u32 atf_strict_sch;
3798 u32 atf_sched_duration;
3799 u32 ant_plzn;
3800 u32 mgmt_retry_limit;
3801 u32 sensitivity_level;
3802 u32 signed_txpower_2g;
3803 u32 signed_txpower_5g;
3804 u32 enable_per_tid_amsdu;
3805 u32 enable_per_tid_ampdu;
3806 u32 cca_threshold;
3807 u32 rts_fixed_rate;
3808 u32 pdev_reset;
3809 u32 wapi_mbssid_offset;
3810 u32 arp_srcaddr;
3811 u32 arp_dstaddr;
3812 u32 enable_btcoex;
3813 u32 rfkill_config;
3814 u32 rfkill_enable;
3815 u32 peer_stats_info_enable;
3816 };
3818 #define WMI_PDEV_PARAM_UNSUPPORTED 0
3821 /* TX chain mask */
3823 /* RX chain mask */
3824 WMI_PDEV_PARAM_RX_CHAIN_MASK,
3825 /* TX power limit for 2G Radio */
3826 WMI_PDEV_PARAM_TXPOWER_LIMIT2G,
3827 /* TX power limit for 5G Radio */
3828 WMI_PDEV_PARAM_TXPOWER_LIMIT5G,
3829 /* TX power scale */
3830 WMI_PDEV_PARAM_TXPOWER_SCALE,
3831 /* Beacon generation mode . 0: host, 1: target */
3832 WMI_PDEV_PARAM_BEACON_GEN_MODE,
3833 /* Beacon generation mode . 0: staggered 1: bursted */
3834 WMI_PDEV_PARAM_BEACON_TX_MODE,
3835 /*
3836 * Resource manager off chan mode .
3837 * 0: turn off offchan mode. 1: turn on offchan mode
3838 */
3839 WMI_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
3840 /*
3841 * Protection mode:
3842 * 0: no protection 1:use CTS-to-self 2: use RTS/CTS
3843 */
3844 WMI_PDEV_PARAM_PROTECTION_MODE,
3845 /*
3846 * Dynamic bandwidth - 0: disable, 1: enable
3847 *
3848 * When enabled HW rate control tries different bandwidths when
3849 * retransmitting frames.
3850 */
3851 WMI_PDEV_PARAM_DYNAMIC_BW,
3852 /* Non aggregrate/ 11g sw retry threshold.0-disable */
3853 WMI_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
3854 /* aggregrate sw retry threshold. 0-disable*/
3855 WMI_PDEV_PARAM_AGG_SW_RETRY_TH,
3856 /* Station kickout threshold (non of consecutive failures).0-disable */
3857 WMI_PDEV_PARAM_STA_KICKOUT_TH,
3858 /* Aggerate size scaling configuration per AC */
3859 WMI_PDEV_PARAM_AC_AGGRSIZE_SCALING,
3860 /* LTR enable */
3861 WMI_PDEV_PARAM_LTR_ENABLE,
3862 /* LTR latency for BE, in us */
3863 WMI_PDEV_PARAM_LTR_AC_LATENCY_BE,
3864 /* LTR latency for BK, in us */
3865 WMI_PDEV_PARAM_LTR_AC_LATENCY_BK,
3866 /* LTR latency for VI, in us */
3867 WMI_PDEV_PARAM_LTR_AC_LATENCY_VI,
3868 /* LTR latency for VO, in us */
3869 WMI_PDEV_PARAM_LTR_AC_LATENCY_VO,
3870 /* LTR AC latency timeout, in ms */
3871 WMI_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
3872 /* LTR platform latency override, in us */
3873 WMI_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
3874 /* LTR-RX override, in us */
3875 WMI_PDEV_PARAM_LTR_RX_OVERRIDE,
3876 /* Tx activity timeout for LTR, in us */
3877 WMI_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
3878 /* L1SS state machine enable */
3879 WMI_PDEV_PARAM_L1SS_ENABLE,
3880 /* Deep sleep state machine enable */
3881 WMI_PDEV_PARAM_DSLEEP_ENABLE,
3882 /* RX buffering flush enable */
3883 WMI_PDEV_PARAM_PCIELP_TXBUF_FLUSH,
3884 /* RX buffering matermark */
3885 WMI_PDEV_PARAM_PCIELP_TXBUF_WATERMARK,
3886 /* RX buffering timeout enable */
3887 WMI_PDEV_PARAM_PCIELP_TXBUF_TMO_EN,
3888 /* RX buffering timeout value */
3889 WMI_PDEV_PARAM_PCIELP_TXBUF_TMO_VALUE,
3890 /* pdev level stats update period in ms */
3891 WMI_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
3892 /* vdev level stats update period in ms */
3893 WMI_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
3894 /* peer level stats update period in ms */
3895 WMI_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
3896 /* beacon filter status update period */
3897 WMI_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
3898 /* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */
3899 WMI_PDEV_PARAM_PMF_QOS,
3900 /* Access category on which ARP frames are sent */
3901 WMI_PDEV_PARAM_ARP_AC_OVERRIDE,
3902 /* DCS configuration */
3903 WMI_PDEV_PARAM_DCS,
3904 /* Enable/Disable ANI on target */
3905 WMI_PDEV_PARAM_ANI_ENABLE,
3906 /* configure the ANI polling period */
3907 WMI_PDEV_PARAM_ANI_POLL_PERIOD,
3908 /* configure the ANI listening period */
3909 WMI_PDEV_PARAM_ANI_LISTEN_PERIOD,
3910 /* configure OFDM immunity level */
3911 WMI_PDEV_PARAM_ANI_OFDM_LEVEL,
3912 /* configure CCK immunity level */
3913 WMI_PDEV_PARAM_ANI_CCK_LEVEL,
3914 /* Enable/Disable CDD for 1x1 STAs in rate control module */
3915 WMI_PDEV_PARAM_DYNTXCHAIN,
3916 /* Enable/Disable proxy STA */
3917 WMI_PDEV_PARAM_PROXY_STA,
3918 /* Enable/Disable low power state when all VDEVs are inactive/idle. */
3919 WMI_PDEV_PARAM_IDLE_PS_CONFIG,
3920 /* Enable/Disable power gating sleep */
3921 WMI_PDEV_PARAM_POWER_GATING_SLEEP,
3922 };
3925 /* TX chian mask */
3927 /* RX chian mask */
3928 WMI_10X_PDEV_PARAM_RX_CHAIN_MASK,
3929 /* TX power limit for 2G Radio */
3930 WMI_10X_PDEV_PARAM_TXPOWER_LIMIT2G,
3931 /* TX power limit for 5G Radio */
3932 WMI_10X_PDEV_PARAM_TXPOWER_LIMIT5G,
3933 /* TX power scale */
3934 WMI_10X_PDEV_PARAM_TXPOWER_SCALE,
3935 /* Beacon generation mode . 0: host, 1: target */
3936 WMI_10X_PDEV_PARAM_BEACON_GEN_MODE,
3937 /* Beacon generation mode . 0: staggered 1: bursted */
3938 WMI_10X_PDEV_PARAM_BEACON_TX_MODE,
3939 /*
3940 * Resource manager off chan mode .
3941 * 0: turn off offchan mode. 1: turn on offchan mode
3942 */
3943 WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
3944 /*
3945 * Protection mode:
3946 * 0: no protection 1:use CTS-to-self 2: use RTS/CTS
3947 */
3948 WMI_10X_PDEV_PARAM_PROTECTION_MODE,
3949 /* Dynamic bandwidth 0: disable 1: enable */
3950 WMI_10X_PDEV_PARAM_DYNAMIC_BW,
3951 /* Non aggregrate/ 11g sw retry threshold.0-disable */
3952 WMI_10X_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
3953 /* aggregrate sw retry threshold. 0-disable*/
3954 WMI_10X_PDEV_PARAM_AGG_SW_RETRY_TH,
3955 /* Station kickout threshold (non of consecutive failures).0-disable */
3956 WMI_10X_PDEV_PARAM_STA_KICKOUT_TH,
3957 /* Aggerate size scaling configuration per AC */
3958 WMI_10X_PDEV_PARAM_AC_AGGRSIZE_SCALING,
3959 /* LTR enable */
3960 WMI_10X_PDEV_PARAM_LTR_ENABLE,
3961 /* LTR latency for BE, in us */
3962 WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BE,
3963 /* LTR latency for BK, in us */
3964 WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BK,
3965 /* LTR latency for VI, in us */
3966 WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VI,
3967 /* LTR latency for VO, in us */
3968 WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VO,
3969 /* LTR AC latency timeout, in ms */
3970 WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
3971 /* LTR platform latency override, in us */
3972 WMI_10X_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
3973 /* LTR-RX override, in us */
3974 WMI_10X_PDEV_PARAM_LTR_RX_OVERRIDE,
3975 /* Tx activity timeout for LTR, in us */
3976 WMI_10X_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
3977 /* L1SS state machine enable */
3978 WMI_10X_PDEV_PARAM_L1SS_ENABLE,
3979 /* Deep sleep state machine enable */
3980 WMI_10X_PDEV_PARAM_DSLEEP_ENABLE,
3981 /* pdev level stats update period in ms */
3982 WMI_10X_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
3983 /* vdev level stats update period in ms */
3984 WMI_10X_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
3985 /* peer level stats update period in ms */
3986 WMI_10X_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
3987 /* beacon filter status update period */
3988 WMI_10X_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
3989 /* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */
3990 WMI_10X_PDEV_PARAM_PMF_QOS,
3991 /* Access category on which ARP and DHCP frames are sent */
3992 WMI_10X_PDEV_PARAM_ARPDHCP_AC_OVERRIDE,
3993 /* DCS configuration */
3994 WMI_10X_PDEV_PARAM_DCS,
3995 /* Enable/Disable ANI on target */
3996 WMI_10X_PDEV_PARAM_ANI_ENABLE,
3997 /* configure the ANI polling period */
3998 WMI_10X_PDEV_PARAM_ANI_POLL_PERIOD,
3999 /* configure the ANI listening period */
4000 WMI_10X_PDEV_PARAM_ANI_LISTEN_PERIOD,
4001 /* configure OFDM immunity level */
4002 WMI_10X_PDEV_PARAM_ANI_OFDM_LEVEL,
4003 /* configure CCK immunity level */
4004 WMI_10X_PDEV_PARAM_ANI_CCK_LEVEL,
4005 /* Enable/Disable CDD for 1x1 STAs in rate control module */
4006 WMI_10X_PDEV_PARAM_DYNTXCHAIN,
4007 /* Enable/Disable Fast channel reset*/
4008 WMI_10X_PDEV_PARAM_FAST_CHANNEL_RESET,
4009 /* Set Bursting DUR */
4010 WMI_10X_PDEV_PARAM_BURST_DUR,
4011 /* Set Bursting Enable*/
4012 WMI_10X_PDEV_PARAM_BURST_ENABLE,
4014 /* following are available as of firmware 10.2 */
4015 WMI_10X_PDEV_PARAM_SMART_ANTENNA_DEFAULT_ANTENNA,
4016 WMI_10X_PDEV_PARAM_IGMPMLD_OVERRIDE,
4017 WMI_10X_PDEV_PARAM_IGMPMLD_TID,
4018 WMI_10X_PDEV_PARAM_ANTENNA_GAIN,
4019 WMI_10X_PDEV_PARAM_RX_DECAP_MODE,
4020 WMI_10X_PDEV_PARAM_RX_FILTER,
4021 WMI_10X_PDEV_PARAM_SET_MCAST_TO_UCAST_TID,
4022 WMI_10X_PDEV_PARAM_PROXY_STA_MODE,
4023 WMI_10X_PDEV_PARAM_SET_MCAST2UCAST_MODE,
4024 WMI_10X_PDEV_PARAM_SET_MCAST2UCAST_BUFFER,
4025 WMI_10X_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER,
4026 WMI_10X_PDEV_PARAM_PEER_STA_PS_STATECHG_ENABLE,
4027 WMI_10X_PDEV_PARAM_RTS_FIXED_RATE,
4028 WMI_10X_PDEV_PARAM_CAL_PERIOD,
4029 WMI_10X_PDEV_PARAM_ATF_STRICT_SCH,
4030 WMI_10X_PDEV_PARAM_ATF_SCHED_DURATION,
4031 WMI_10X_PDEV_PARAM_SET_PROMISC_MODE_CMDID,
4032 WMI_10X_PDEV_PARAM_PDEV_RESET
4033 };
4037 WMI_10_4_PDEV_PARAM_RX_CHAIN_MASK,
4038 WMI_10_4_PDEV_PARAM_TXPOWER_LIMIT2G,
4039 WMI_10_4_PDEV_PARAM_TXPOWER_LIMIT5G,
4040 WMI_10_4_PDEV_PARAM_TXPOWER_SCALE,
4041 WMI_10_4_PDEV_PARAM_BEACON_GEN_MODE,
4042 WMI_10_4_PDEV_PARAM_BEACON_TX_MODE,
4043 WMI_10_4_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
4044 WMI_10_4_PDEV_PARAM_PROTECTION_MODE,
4045 WMI_10_4_PDEV_PARAM_DYNAMIC_BW,
4046 WMI_10_4_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
4047 WMI_10_4_PDEV_PARAM_AGG_SW_RETRY_TH,
4048 WMI_10_4_PDEV_PARAM_STA_KICKOUT_TH,
4049 WMI_10_4_PDEV_PARAM_AC_AGGRSIZE_SCALING,
4050 WMI_10_4_PDEV_PARAM_LTR_ENABLE,
4051 WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_BE,
4052 WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_BK,
4053 WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_VI,
4054 WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_VO,
4055 WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
4056 WMI_10_4_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
4057 WMI_10_4_PDEV_PARAM_LTR_RX_OVERRIDE,
4058 WMI_10_4_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
4059 WMI_10_4_PDEV_PARAM_L1SS_ENABLE,
4060 WMI_10_4_PDEV_PARAM_DSLEEP_ENABLE,
4061 WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_FLUSH,
4062 WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_WATERMARK,
4063 WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_TMO_EN,
4064 WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_TMO_VALUE,
4065 WMI_10_4_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
4066 WMI_10_4_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
4067 WMI_10_4_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
4068 WMI_10_4_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
4069 WMI_10_4_PDEV_PARAM_PMF_QOS,
4070 WMI_10_4_PDEV_PARAM_ARP_AC_OVERRIDE,
4071 WMI_10_4_PDEV_PARAM_DCS,
4072 WMI_10_4_PDEV_PARAM_ANI_ENABLE,
4073 WMI_10_4_PDEV_PARAM_ANI_POLL_PERIOD,
4074 WMI_10_4_PDEV_PARAM_ANI_LISTEN_PERIOD,
4075 WMI_10_4_PDEV_PARAM_ANI_OFDM_LEVEL,
4076 WMI_10_4_PDEV_PARAM_ANI_CCK_LEVEL,
4077 WMI_10_4_PDEV_PARAM_DYNTXCHAIN,
4078 WMI_10_4_PDEV_PARAM_PROXY_STA,
4079 WMI_10_4_PDEV_PARAM_IDLE_PS_CONFIG,
4080 WMI_10_4_PDEV_PARAM_POWER_GATING_SLEEP,
4081 WMI_10_4_PDEV_PARAM_AGGR_BURST,
4082 WMI_10_4_PDEV_PARAM_RX_DECAP_MODE,
4083 WMI_10_4_PDEV_PARAM_FAST_CHANNEL_RESET,
4084 WMI_10_4_PDEV_PARAM_BURST_DUR,
4085 WMI_10_4_PDEV_PARAM_BURST_ENABLE,
4086 WMI_10_4_PDEV_PARAM_SMART_ANTENNA_DEFAULT_ANTENNA,
4087 WMI_10_4_PDEV_PARAM_IGMPMLD_OVERRIDE,
4088 WMI_10_4_PDEV_PARAM_IGMPMLD_TID,
4089 WMI_10_4_PDEV_PARAM_ANTENNA_GAIN,
4090 WMI_10_4_PDEV_PARAM_RX_FILTER,
4091 WMI_10_4_PDEV_SET_MCAST_TO_UCAST_TID,
4092 WMI_10_4_PDEV_PARAM_PROXY_STA_MODE,
4093 WMI_10_4_PDEV_PARAM_SET_MCAST2UCAST_MODE,
4094 WMI_10_4_PDEV_PARAM_SET_MCAST2UCAST_BUFFER,
4095 WMI_10_4_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER,
4096 WMI_10_4_PDEV_PEER_STA_PS_STATECHG_ENABLE,
4097 WMI_10_4_PDEV_PARAM_IGMPMLD_AC_OVERRIDE,
4098 WMI_10_4_PDEV_PARAM_BLOCK_INTERBSS,
4099 WMI_10_4_PDEV_PARAM_SET_DISABLE_RESET_CMDID,
4100 WMI_10_4_PDEV_PARAM_SET_MSDU_TTL_CMDID,
4101 WMI_10_4_PDEV_PARAM_SET_PPDU_DURATION_CMDID,
4102 WMI_10_4_PDEV_PARAM_TXBF_SOUND_PERIOD_CMDID,
4103 WMI_10_4_PDEV_PARAM_SET_PROMISC_MODE_CMDID,
4104 WMI_10_4_PDEV_PARAM_SET_BURST_MODE_CMDID,
4105 WMI_10_4_PDEV_PARAM_EN_STATS,
4106 WMI_10_4_PDEV_PARAM_MU_GROUP_POLICY,
4107 WMI_10_4_PDEV_PARAM_NOISE_DETECTION,
4108 WMI_10_4_PDEV_PARAM_NOISE_THRESHOLD,
4109 WMI_10_4_PDEV_PARAM_DPD_ENABLE,
4110 WMI_10_4_PDEV_PARAM_SET_MCAST_BCAST_ECHO,
4111 WMI_10_4_PDEV_PARAM_ATF_STRICT_SCH,
4112 WMI_10_4_PDEV_PARAM_ATF_SCHED_DURATION,
4113 WMI_10_4_PDEV_PARAM_ANT_PLZN,
4114 WMI_10_4_PDEV_PARAM_MGMT_RETRY_LIMIT,
4115 WMI_10_4_PDEV_PARAM_SENSITIVITY_LEVEL,
4116 WMI_10_4_PDEV_PARAM_SIGNED_TXPOWER_2G,
4117 WMI_10_4_PDEV_PARAM_SIGNED_TXPOWER_5G,
4118 WMI_10_4_PDEV_PARAM_ENABLE_PER_TID_AMSDU,
4119 WMI_10_4_PDEV_PARAM_ENABLE_PER_TID_AMPDU,
4120 WMI_10_4_PDEV_PARAM_CCA_THRESHOLD,
4121 WMI_10_4_PDEV_PARAM_RTS_FIXED_RATE,
4122 WMI_10_4_PDEV_PARAM_CAL_PERIOD,
4123 WMI_10_4_PDEV_PARAM_PDEV_RESET,
4124 WMI_10_4_PDEV_PARAM_WAPI_MBSSID_OFFSET,
4125 WMI_10_4_PDEV_PARAM_ARP_SRCADDR,
4126 WMI_10_4_PDEV_PARAM_ARP_DSTADDR,
4127 WMI_10_4_PDEV_PARAM_TXPOWER_DECR_DB,
4128 WMI_10_4_PDEV_PARAM_RX_BATCHMODE,
4129 WMI_10_4_PDEV_PARAM_PACKET_AGGR_DELAY,
4130 WMI_10_4_PDEV_PARAM_ATF_OBSS_NOISE_SCH,
4131 WMI_10_4_PDEV_PARAM_ATF_OBSS_NOISE_SCALING_FACTOR,
4132 WMI_10_4_PDEV_PARAM_CUST_TXPOWER_SCALE,
4133 WMI_10_4_PDEV_PARAM_ATF_DYNAMIC_ENABLE,
4134 WMI_10_4_PDEV_PARAM_ATF_SSID_GROUP_POLICY,
4135 WMI_10_4_PDEV_PARAM_ENABLE_BTCOEX,
4136 };
4139 __le32 param_id;
4140 __le32 param_value;
4147 /* valid period is 1 ~ 60000ms, unit in millisecond */
4148 #define WMI_PDEV_PARAM_CAL_PERIOD_MAX 60000
4151 /* parameter */
4152 __le32 param;
4155 #define WMI_TPC_CONFIG_PARAM 1
4156 #define WMI_TPC_FINAL_RATE_MAX 240
4157 #define WMI_TPC_TX_N_CHAIN 4
4158 #define WMI_TPC_RATE_MAX (WMI_TPC_TX_N_CHAIN * 65)
4159 #define WMI_TPC_PREAM_TABLE_MAX 10
4160 #define WMI_TPC_FLAG 3
4161 #define WMI_TPC_BUF_SIZE 10
4162 #define WMI_TPC_BEAMFORMING 2
4168 };
4174 };
4177 __le32 reg_domain;
4178 __le32 chan_freq;
4179 __le32 phy_mode;
4180 __le32 twice_antenna_reduction;
4181 __le32 twice_max_rd_power;
4182 a_sle32 twice_antenna_gain;
4183 __le32 power_limit;
4184 __le32 rate_max;
4185 __le32 num_tx_chain;
4186 __le32 ctl;
4187 __le32 flags;
4195 /* Transmit power scale factor. */
4203 };
4206 __le32 reg_domain;
4207 __le32 chan_freq;
4208 __le32 phy_mode;
4209 __le32 twice_antenna_reduction;
4210 __le32 twice_max_rd_power;
4211 a_sle32 twice_antenna_gain;
4212 __le32 power_limit;
4213 __le32 rate_max;
4214 __le32 num_tx_chain;
4215 __le32 ctl;
4216 __le32 flags;
4227 __le32 param;
4232 WMI_TPC_PREAM_2GHZ_OFDM,
4233 WMI_TPC_PREAM_2GHZ_HT20,
4234 WMI_TPC_PREAM_2GHZ_HT40,
4235 WMI_TPC_PREAM_2GHZ_VHT20,
4236 WMI_TPC_PREAM_2GHZ_VHT40,
4237 WMI_TPC_PREAM_2GHZ_VHT80,
4238 };
4242 WMI_TPC_PREAM_5GHZ_HT20,
4243 WMI_TPC_PREAM_5GHZ_HT40,
4244 WMI_TPC_PREAM_5GHZ_VHT20,
4245 WMI_TPC_PREAM_5GHZ_VHT40,
4246 WMI_TPC_PREAM_5GHZ_VHT80,
4247 WMI_TPC_PREAM_5GHZ_HTCUP,
4248 };
4250 #define WMI_PEER_PS_STATE_DISABLED 2
4254 __le32 peer_ps_state;
4258 /* number of channels */
4259 __le32 num_chan;
4260 /* array of channels */
4264 #define WMI_MAX_DEBUG_MESG (sizeof(u32) * 32)
4267 /* message buffer, NULL terminated */
4272 /* P2P device */
4274 /* P2P client */
4275 VDEV_SUBTYPE_P2PCLI,
4276 /* P2P GO */
4277 VDEV_SUBTYPE_P2PGO,
4278 /* BT3.0 HS */
4279 VDEV_SUBTYPE_BT,
4280 };
4283 /* idnore power , only use flags , mode and freq */
4288 __le32 ev_bitmap;
4291 /* Customize the DSCP (bit) to TID (0-7) mapping for QOS */
4292 #define WMI_DSCP_MAP_MAX (64)
4294 /* map indicating DSCP to TID conversion */
4299 WMI_SET_MCAST_RATE,
4300 WMI_SET_BCAST_RATE
4301 };
4305 __le32 rate;
4309 __le32 cwmin;
4310 __le32 cwmax;
4311 __le32 aifs;
4312 __le32 txop;
4313 __le32 acm;
4314 __le32 no_ack;
4325 u32 cwmin;
4326 u32 cwmax;
4327 u32 aifs;
4328 u32 txop;
4329 u32 acm;
4330 u32 no_ack;
4331 };
4338 };
4341 /* Num HTT cookies queued to dispatch list */
4342 __le32 comp_queued;
4344 /* Num HTT cookies dispatched */
4345 __le32 comp_delivered;
4347 /* Num MSDU queued to WAL */
4348 __le32 msdu_enqued;
4350 /* Num MPDU queue to WAL */
4351 __le32 mpdu_enqued;
4353 /* Num MSDUs dropped by WMM limit */
4354 __le32 wmm_drop;
4356 /* Num Local frames queued */
4357 __le32 local_enqued;
4359 /* Num Local frames done */
4360 __le32 local_freed;
4362 /* Num queued to HW */
4363 __le32 hw_queued;
4365 /* Num PPDU reaped from HW */
4366 __le32 hw_reaped;
4368 /* Num underruns */
4369 __le32 underrun;
4371 /* Num PPDUs cleaned up in TX abort */
4372 __le32 tx_abort;
4374 /* Num MPDUs requed by SW */
4375 __le32 mpdus_requed;
4377 /* excessive retries */
4378 __le32 tx_ko;
4380 /* data hw rate code */
4381 __le32 data_rc;
4383 /* Scheduler self triggers */
4384 __le32 self_triggers;
4386 /* frames dropped due to excessive sw retries */
4387 __le32 sw_retry_failure;
4389 /* illegal rate phy errors */
4390 __le32 illgl_rate_phy_err;
4392 /* wal pdev continuous xretry */
4393 __le32 pdev_cont_xretry;
4395 /* wal pdev continous xretry */
4396 __le32 pdev_tx_timeout;
4398 /* wal pdev resets */
4399 __le32 pdev_resets;
4401 /* frames dropped due to non-availability of stateless TIDs */
4402 __le32 stateless_tid_alloc_failure;
4404 __le32 phy_underrun;
4406 /* MPDU is more than txop limit */
4407 __le32 txop_ovf;
4411 /* Num HTT cookies queued to dispatch list */
4412 __le32 comp_queued;
4414 /* Num HTT cookies dispatched */
4415 __le32 comp_delivered;
4417 /* Num MSDU queued to WAL */
4418 __le32 msdu_enqued;
4420 /* Num MPDU queue to WAL */
4421 __le32 mpdu_enqued;
4423 /* Num MSDUs dropped by WMM limit */
4424 __le32 wmm_drop;
4426 /* Num Local frames queued */
4427 __le32 local_enqued;
4429 /* Num Local frames done */
4430 __le32 local_freed;
4432 /* Num queued to HW */
4433 __le32 hw_queued;
4435 /* Num PPDU reaped from HW */
4436 __le32 hw_reaped;
4438 /* Num underruns */
4439 __le32 underrun;
4441 /* HW Paused. */
4442 __le32 hw_paused;
4444 /* Num PPDUs cleaned up in TX abort */
4445 __le32 tx_abort;
4447 /* Num MPDUs requed by SW */
4448 __le32 mpdus_requed;
4450 /* excessive retries */
4451 __le32 tx_ko;
4453 /* data hw rate code */
4454 __le32 data_rc;
4456 /* Scheduler self triggers */
4457 __le32 self_triggers;
4459 /* frames dropped due to excessive sw retries */
4460 __le32 sw_retry_failure;
4462 /* illegal rate phy errors */
4463 __le32 illgl_rate_phy_err;
4465 /* wal pdev continuous xretry */
4466 __le32 pdev_cont_xretry;
4468 /* wal pdev tx timeouts */
4469 __le32 pdev_tx_timeout;
4471 /* wal pdev resets */
4472 __le32 pdev_resets;
4474 /* frames dropped due to non-availability of stateless TIDs */
4475 __le32 stateless_tid_alloc_failure;
4477 __le32 phy_underrun;
4479 /* MPDU is more than txop limit */
4480 __le32 txop_ovf;
4482 /* Number of Sequences posted */
4483 __le32 seq_posted;
4485 /* Number of Sequences failed queueing */
4486 __le32 seq_failed_queueing;
4488 /* Number of Sequences completed */
4489 __le32 seq_completed;
4491 /* Number of Sequences restarted */
4492 __le32 seq_restarted;
4494 /* Number of MU Sequences posted */
4495 __le32 mu_seq_posted;
4497 /* Num MPDUs flushed by SW, HWPAUSED,SW TXABORT(Reset,channel change) */
4498 __le32 mpdus_sw_flush;
4500 /* Num MPDUs filtered by HW, all filter condition (TTL expired) */
4501 __le32 mpdus_hw_filter;
4503 /* Num MPDUs truncated by PDG
4504 * (TXOP, TBTT, PPDU_duration based on rate, dyn_bw)
4505 */
4506 __le32 mpdus_truncated;
4508 /* Num MPDUs that was tried but didn't receive ACK or BA */
4509 __le32 mpdus_ack_failed;
4511 /* Num MPDUs that was dropped due to expiry. */
4512 __le32 mpdus_expired;
4516 /* Cnts any change in ring routing mid-ppdu */
4517 __le32 mid_ppdu_route_change;
4519 /* Total number of statuses processed */
4520 __le32 status_rcvd;
4522 /* Extra frags on rings 0-3 */
4523 __le32 r0_frags;
4524 __le32 r1_frags;
4525 __le32 r2_frags;
4526 __le32 r3_frags;
4528 /* MSDUs / MPDUs delivered to HTT */
4529 __le32 htt_msdus;
4530 __le32 htt_mpdus;
4532 /* MSDUs / MPDUs delivered to local stack */
4533 __le32 loc_msdus;
4534 __le32 loc_mpdus;
4536 /* AMSDUs that have more MSDUs than the status ring size */
4537 __le32 oversize_amsdu;
4539 /* Number of PHY errors */
4540 __le32 phy_errs;
4542 /* Number of PHY errors drops */
4543 __le32 phy_err_drop;
4545 /* Number of mpdu errors - FCS, MIC, ENC etc. */
4546 __le32 mpdu_errs;
4550 /* REMOVE THIS ONCE REAL PEER STAT COUNTERS ARE ADDED */
4551 __le32 dummy;
4561 };
4569 };
4577 };
4580 __le16 cfg_retry_count;
4581 __le16 retry_count;
4582 };
4585 __le32 stats_id;
4587 __le32 vdev_id;
4589 /* peer MAC address */
4592 /* Instantaneous RSSI arguments */
4597 /* request stats of one specified peer */
4599 /* request stats of all peers belong to specified VDEV */
4601 };
4603 /* Suspend option */
4605 /* suspend */
4606 WMI_PDEV_SUSPEND,
4608 /* suspend and disable all interrupts */
4609 WMI_PDEV_SUSPEND_AND_DISABLE_INTR,
4610 };
4613 /* suspend option sent to target */
4614 __le32 suspend_opt;
4619 /*
4620 * number of pdev stats event structures
4621 * (wmi_pdev_stats) 0 or 1
4622 */
4623 __le32 num_pdev_stats;
4624 /*
4625 * number of vdev stats event structures
4626 * (wmi_vdev_stats) 0 or max vdevs
4627 */
4628 __le32 num_vdev_stats;
4629 /*
4630 * number of peer stats event structures
4631 * (wmi_peer_stats) 0 or max peers
4632 */
4633 __le32 num_peer_stats;
4634 __le32 num_bcnflt_stats;
4635 /*
4636 * followed by
4637 * num_pdev_stats * size of(struct wmi_pdev_stats)
4638 * num_vdev_stats * size of(struct wmi_vdev_stats)
4639 * num_peer_stats * size of(struct wmi_peer_stats)
4640 *
4641 * By having a zero sized array, the pointer to data area
4642 * becomes available without increasing the struct size
4643 */
4644 u8 data[];
4649 __le32 num_pdev_stats;
4650 __le32 num_pdev_ext_stats;
4651 __le32 num_vdev_stats;
4652 __le32 num_peer_stats;
4653 __le32 num_bcnflt_stats;
4654 u8 data[];
4657 /*
4658 * PDEV statistics
4659 * TODO: add all PDEV stats here
4660 */
4662 __le32 chan_nf;
4667 __le32 phy_err_count;
4668 __le32 chan_tx_pwr;
4679 __le32 ack_rx_bad;
4680 __le32 rts_bad;
4681 __le32 rts_good;
4682 __le32 fcs_bad;
4683 __le32 no_beacons;
4684 __le32 mib_int_count;
4696 __le32 dram_free;
4697 __le32 iram_free;
4703 __le32 mc_drop;
4705 __le32 pdev_rx_timeout;
4715 __le32 rx_ovfl_errs;
4717 __le32 sram_free_size;
4721 /*
4722 * VDEV statistics
4723 */
4725 #define WMI_VDEV_STATS_FTM_COUNT_VALID BIT(31)
4726 #define WMI_VDEV_STATS_FTM_COUNT_LSB 0
4727 #define WMI_VDEV_STATS_FTM_COUNT_MASK 0x7fffffff
4730 __le32 vdev_id;
4734 __le32 vdev_id;
4735 __le32 ppdu_aggr_cnt;
4736 __le32 ppdu_noack;
4737 __le32 mpdu_queued;
4738 __le32 ppdu_nonaggr_cnt;
4739 __le32 mpdu_sw_requeued;
4740 __le32 mpdu_suc_retry;
4741 __le32 mpdu_suc_multitry;
4742 __le32 mpdu_fail_retry;
4743 __le32 tx_ftm_suc;
4744 __le32 tx_ftm_suc_retry;
4745 __le32 tx_ftm_fail;
4746 __le32 rx_ftmr_cnt;
4747 __le32 rx_ftmr_dup_cnt;
4748 __le32 rx_iftmr_cnt;
4749 __le32 rx_iftmr_dup_cnt;
4753 /*
4754 * peer statistics.
4755 * TODO: add more stats
4756 */
4759 __le32 peer_rssi;
4760 __le32 peer_tx_rate;
4765 __le32 peer_rx_rate;
4770 __le32 peer_rx_rate;
4771 __le32 current_per;
4772 __le32 retries;
4773 __le32 tx_rate_count;
4774 __le32 max_4ms_frame_len;
4775 __le32 total_sub_frames;
4776 __le32 tx_bytes;
4783 __le32 peer_rssi_changed;
4788 __le32 peer_rssi_changed;
4789 __le32 rx_duration;
4794 __le32 peer_rssi;
4795 __le32 peer_rssi_seq_num;
4796 __le32 peer_tx_rate;
4797 __le32 peer_rx_rate;
4798 __le32 current_per;
4799 __le32 retries;
4800 __le32 tx_rate_count;
4801 __le32 max_4ms_frame_len;
4802 __le32 total_sub_frames;
4803 __le32 tx_bytes;
4806 __le32 peer_rssi_changed;
4811 __le32 inactive_time;
4812 __le32 peer_chain_rssi;
4813 __le32 rx_duration;
4818 __le32 vdev_id;
4819 __le32 bss_bcns_dropped;
4820 __le32 bss_bcn_delivered;
4824 __le32 bcns_dropped;
4825 __le32 bcns_delivered;
4826 __le32 active_filters;
4831 __le32 rx_rssi_comb;
4835 __le32 ack_rssi;
4839 __le32 vdev_id;
4840 __le32 vdev_type;
4841 __le32 vdev_subtype;
4850 };
4853 WMI_VDEV_SUBTYPE_NONE,
4854 WMI_VDEV_SUBTYPE_P2P_DEVICE,
4855 WMI_VDEV_SUBTYPE_P2P_CLIENT,
4856 WMI_VDEV_SUBTYPE_P2P_GO,
4857 WMI_VDEV_SUBTYPE_PROXY_STA,
4858 WMI_VDEV_SUBTYPE_MESH_11S,
4859 WMI_VDEV_SUBTYPE_MESH_NON_11S,
4860 };
4868 };
4877 };
4887 };
4889 /* values for vdev_subtype */
4891 /* values for vdev_start_request flags */
4892 /*
4893 * Indicates that AP VDEV uses hidden ssid. only valid for
4894 * AP/GO
4895 */
4896 #define WMI_VDEV_START_HIDDEN_SSID (1 << 0)
4897 /*
4898 * Indicates if robust management frame/management frame
4899 * protection is enabled. For GO/AP vdevs, it indicates that
4900 * it may support station/client associations with RMF enabled.
4901 * For STA/client vdevs, it indicates that sta will
4902 * associate with AP with RMF enabled.
4903 */
4904 #define WMI_VDEV_START_PMF_ENABLED (1 << 1)
4914 /* WMI channel */
4916 /* unique id identifying the VDEV, generated by the caller */
4917 __le32 vdev_id;
4918 /* requestor id identifying the caller module */
4919 __le32 requestor_id;
4920 /* beacon interval from received beacon */
4921 __le32 beacon_interval;
4922 /* DTIM Period from the received beacon */
4923 __le32 dtim_period;
4924 /* Flags */
4925 __le32 flags;
4926 /* ssid field. Only valid for AP/GO/IBSS/BTAmp VDEV type. */
4928 /* beacon/probe response xmit rate. Applicable for SoftAP. */
4929 __le32 bcn_tx_rate;
4930 /* beacon/probe response xmit power. Applicable for SoftAP. */
4931 __le32 bcn_tx_power;
4932 /* number of p2p NOA descriptor(s) from scan entry */
4933 __le32 num_noa_descriptors;
4934 /*
4935 * Disable H/W ack. This used by WMI_VDEV_RESTART_REQUEST_CMDID.
4936 * During CAC, Our HW shouldn't ack ditected frames
4937 */
4938 __le32 disable_hw_ack;
4939 /* actual p2p NOA descriptor from scan entry */
4948 u32 vdev_id;
4950 u32 bcn_intval;
4951 u32 dtim_period;
4953 u32 ssid_len;
4954 u32 bcn_tx_rate;
4955 u32 bcn_tx_power;
4959 };
4962 /* unique id identifying the VDEV, generated by the caller */
4963 __le32 vdev_id;
4967 __le32 vdev_id;
4968 __le32 vdev_assoc_id;
4973 __le32 vdev_id;
4977 __le32 vdev_id;
4981 /* unique id identifying the VDEV, generated by the caller */
4982 __le32 vdev_id;
4986 /* unique id identifying the VDEV, generated by the caller */
4987 __le32 vdev_id;
4991 __le32 vdev_id;
4992 __le32 param_id;
4993 __le32 param_value;
4996 #define WMI_MAX_KEY_INDEX 3
4997 #define WMI_MAX_KEY_LEN 32
4999 #define WMI_KEY_PAIRWISE 0x00
5000 #define WMI_KEY_GROUP 0x01
5004 __le32 key_seq_counter_l;
5005 __le32 key_seq_counter_h;
5009 WMI_CIPHER_NONE,
5010 WMI_CIPHER_WEP,
5011 WMI_CIPHER_TKIP,
5012 WMI_CIPHER_AES_OCB,
5013 WMI_CIPHER_AES_CCM,
5014 WMI_CIPHER_WAPI,
5015 WMI_CIPHER_CKIP,
5016 WMI_CIPHER_AES_CMAC,
5017 WMI_CIPHER_AES_GCM,
5018 };
5021 WMI_TLV_CIPHER_NONE,
5022 WMI_TLV_CIPHER_WEP,
5023 WMI_TLV_CIPHER_TKIP,
5024 WMI_TLV_CIPHER_AES_OCB,
5025 WMI_TLV_CIPHER_AES_CCM,
5026 WMI_TLV_CIPHER_WAPI,
5027 WMI_TLV_CIPHER_CKIP,
5028 WMI_TLV_CIPHER_AES_CMAC,
5029 WMI_TLV_CIPHER_ANY,
5030 WMI_TLV_CIPHER_AES_GCM,
5031 };
5034 __le32 vdev_id;
5036 __le32 key_idx;
5037 __le32 key_flags;
5044 __le32 key_len;
5045 __le32 key_txmic_len;
5046 __le32 key_rxmic_len;
5048 /* contains key followed by tx mic followed by rx mic */
5049 u8 key_data[];
5053 u32 vdev_id;
5055 u32 key_idx;
5056 u32 key_flags;
5057 u32 key_cipher;
5058 u32 key_len;
5059 u32 key_txmic_len;
5060 u32 key_rxmic_len;
5062 };
5064 /*
5065 * vdev fixed rate format:
5066 * - preamble - b7:b6 - see WMI_RATE_PREMABLE_
5067 * - nss - b5:b4 - ss number (0 mean 1ss)
5068 * - rate_mcs - b3:b0 - as below
5069 * CCK: 0 - 11Mbps, 1 - 5,5Mbps, 2 - 2Mbps, 3 - 1Mbps,
5070 * 4 - 11Mbps (s), 5 - 5,5Mbps (s), 6 - 2Mbps (s)
5071 * OFDM: 0 - 48Mbps, 1 - 24Mbps, 2 - 12Mbps, 3 - 6Mbps,
5072 * 4 - 54Mbps, 5 - 36Mbps, 6 - 18Mbps, 7 - 9Mbps
5073 * HT/VHT: MCS index
5074 */
5076 /* Preamble types to be used with VDEV fixed rate configuration */
5078 WMI_RATE_PREAMBLE_OFDM,
5079 WMI_RATE_PREAMBLE_CCK,
5080 WMI_RATE_PREAMBLE_HT,
5081 WMI_RATE_PREAMBLE_VHT,
5082 };
5084 #define ATH10K_HW_NSS(rate) (1 + (((rate) >> 4) & 0x3))
5085 #define ATH10K_HW_PREAMBLE(rate) (((rate) >> 6) & 0x3)
5086 #define ATH10K_HW_MCS_RATE(rate) ((rate) & 0xf)
5087 #define ATH10K_HW_LEGACY_RATE(rate) ((rate) & 0x3f)
5088 #define ATH10K_HW_BW(flags) (((flags) >> 3) & 0x3)
5089 #define ATH10K_HW_GI(flags) (((flags) >> 5) & 0x1)
5090 #define ATH10K_HW_RATECODE(rate, nss, preamble) \
5091 (((preamble) << 6) | ((nss) << 4) | (rate))
5092 #define ATH10K_HW_AMPDU(flags) ((flags) & 0x1)
5093 #define ATH10K_HW_BA_FAIL(flags) (((flags) >> 1) & 0x3)
5094 #define ATH10K_FW_SKIPPED_RATE_CTRL(flags) (((flags) >> 6) & 0x1)
5096 #define ATH10K_VHT_MCS_NUM 10
5097 #define ATH10K_BW_NUM 6
5098 #define ATH10K_NSS_NUM 4
5099 #define ATH10K_LEGACY_NUM 12
5100 #define ATH10K_GI_NUM 2
5101 #define ATH10K_HT_MCS_NUM 32
5102 #define ATH10K_RATE_TABLE_NUM 320
5103 #define ATH10K_RATE_INFO_FLAGS_SGI_BIT 2
5105 /* Value to disable fixed rate setting */
5106 #define WMI_FIXED_RATE_NONE (0xff)
5109 u32 smps_state;
5110 u32 ampdu;
5111 u32 authorize;
5112 u32 chan_width;
5113 u32 nss;
5114 u32 use_4addr;
5115 u32 membership;
5116 u32 use_fixed_power;
5117 u32 user_pos;
5118 u32 crit_proto_hint_enabled;
5119 u32 tx_fail_cnt_thr;
5120 u32 set_hw_retry_cts2s;
5121 u32 ibss_atim_win_len;
5122 u32 debug;
5123 u32 phymode;
5124 u32 dummy_var;
5125 };
5128 u32 rts_threshold;
5129 u32 fragmentation_threshold;
5130 u32 beacon_interval;
5131 u32 listen_interval;
5132 u32 multicast_rate;
5133 u32 mgmt_tx_rate;
5134 u32 slot_time;
5135 u32 preamble;
5136 u32 swba_time;
5137 u32 wmi_vdev_stats_update_period;
5138 u32 wmi_vdev_pwrsave_ageout_time;
5139 u32 wmi_vdev_host_swba_interval;
5140 u32 dtim_period;
5141 u32 wmi_vdev_oc_scheduler_air_time_limit;
5142 u32 wds;
5143 u32 atim_window;
5144 u32 bmiss_count_max;
5145 u32 bmiss_first_bcnt;
5146 u32 bmiss_final_bcnt;
5147 u32 feature_wmm;
5148 u32 chwidth;
5149 u32 chextoffset;
5150 u32 disable_htprotection;
5151 u32 sta_quickkickout;
5152 u32 mgmt_rate;
5153 u32 protection_mode;
5154 u32 fixed_rate;
5155 u32 sgi;
5156 u32 ldpc;
5157 u32 tx_stbc;
5158 u32 rx_stbc;
5159 u32 intra_bss_fwd;
5160 u32 def_keyid;
5161 u32 nss;
5162 u32 bcast_data_rate;
5163 u32 mcast_data_rate;
5164 u32 mcast_indicate;
5165 u32 dhcp_indicate;
5166 u32 unknown_dest_indicate;
5167 u32 ap_keepalive_min_idle_inactive_time_secs;
5168 u32 ap_keepalive_max_idle_inactive_time_secs;
5169 u32 ap_keepalive_max_unresponsive_time_secs;
5170 u32 ap_enable_nawds;
5171 u32 mcast2ucast_set;
5172 u32 enable_rtscts;
5173 u32 txbf;
5174 u32 packet_powersave;
5175 u32 drop_unencry;
5176 u32 tx_encap_type;
5177 u32 ap_detect_out_of_sync_sleeping_sta_time_secs;
5178 u32 rc_num_retries;
5179 u32 cabq_maxdur;
5180 u32 mfptest_set;
5181 u32 rts_fixed_rate;
5182 u32 vht_sgimask;
5183 u32 vht80_ratemask;
5184 u32 early_rx_adjust_enable;
5185 u32 early_rx_tgt_bmiss_num;
5186 u32 early_rx_bmiss_sample_cycle;
5187 u32 early_rx_slop_step;
5188 u32 early_rx_init_slop;
5189 u32 early_rx_adjust_pause;
5190 u32 proxy_sta;
5191 u32 meru_vc;
5192 u32 rx_decap_type;
5193 u32 bw_nss_ratemask;
5194 u32 inc_tsf;
5195 u32 dec_tsf;
5196 u32 disable_4addr_src_lrn;
5197 u32 rtt_responder_role;
5198 };
5200 #define WMI_VDEV_PARAM_UNSUPPORTED 0
5202 /* the definition of different VDEV parameters */
5204 /* RTS Threshold */
5206 /* Fragmentation threshold */
5207 WMI_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
5208 /* beacon interval in TUs */
5209 WMI_VDEV_PARAM_BEACON_INTERVAL,
5210 /* Listen interval in TUs */
5211 WMI_VDEV_PARAM_LISTEN_INTERVAL,
5212 /* multicast rate in Mbps */
5213 WMI_VDEV_PARAM_MULTICAST_RATE,
5214 /* management frame rate in Mbps */
5215 WMI_VDEV_PARAM_MGMT_TX_RATE,
5216 /* slot time (long vs short) */
5217 WMI_VDEV_PARAM_SLOT_TIME,
5218 /* preamble (long vs short) */
5219 WMI_VDEV_PARAM_PREAMBLE,
5220 /* SWBA time (time before tbtt in msec) */
5221 WMI_VDEV_PARAM_SWBA_TIME,
5222 /* time period for updating VDEV stats */
5223 WMI_VDEV_STATS_UPDATE_PERIOD,
5224 /* age out time in msec for frames queued for station in power save */
5225 WMI_VDEV_PWRSAVE_AGEOUT_TIME,
5226 /*
5227 * Host SWBA interval (time in msec before tbtt for SWBA event
5228 * generation).
5229 */
5230 WMI_VDEV_HOST_SWBA_INTERVAL,
5231 /* DTIM period (specified in units of num beacon intervals) */
5232 WMI_VDEV_PARAM_DTIM_PERIOD,
5233 /*
5234 * scheduler air time limit for this VDEV. used by off chan
5235 * scheduler.
5236 */
5237 WMI_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
5238 /* enable/dsiable WDS for this VDEV */
5239 WMI_VDEV_PARAM_WDS,
5240 /* ATIM Window */
5241 WMI_VDEV_PARAM_ATIM_WINDOW,
5242 /* BMISS max */
5243 WMI_VDEV_PARAM_BMISS_COUNT_MAX,
5244 /* BMISS first time */
5245 WMI_VDEV_PARAM_BMISS_FIRST_BCNT,
5246 /* BMISS final time */
5247 WMI_VDEV_PARAM_BMISS_FINAL_BCNT,
5248 /* WMM enables/disabled */
5249 WMI_VDEV_PARAM_FEATURE_WMM,
5250 /* Channel width */
5251 WMI_VDEV_PARAM_CHWIDTH,
5252 /* Channel Offset */
5253 WMI_VDEV_PARAM_CHEXTOFFSET,
5254 /* Disable HT Protection */
5255 WMI_VDEV_PARAM_DISABLE_HTPROTECTION,
5256 /* Quick STA Kickout */
5257 WMI_VDEV_PARAM_STA_QUICKKICKOUT,
5258 /* Rate to be used with Management frames */
5259 WMI_VDEV_PARAM_MGMT_RATE,
5260 /* Protection Mode */
5261 WMI_VDEV_PARAM_PROTECTION_MODE,
5262 /* Fixed rate setting */
5263 WMI_VDEV_PARAM_FIXED_RATE,
5264 /* Short GI Enable/Disable */
5265 WMI_VDEV_PARAM_SGI,
5266 /* Enable LDPC */
5267 WMI_VDEV_PARAM_LDPC,
5268 /* Enable Tx STBC */
5269 WMI_VDEV_PARAM_TX_STBC,
5270 /* Enable Rx STBC */
5271 WMI_VDEV_PARAM_RX_STBC,
5272 /* Intra BSS forwarding */
5273 WMI_VDEV_PARAM_INTRA_BSS_FWD,
5274 /* Setting Default xmit key for Vdev */
5275 WMI_VDEV_PARAM_DEF_KEYID,
5276 /* NSS width */
5277 WMI_VDEV_PARAM_NSS,
5278 /* Set the custom rate for the broadcast data frames */
5279 WMI_VDEV_PARAM_BCAST_DATA_RATE,
5280 /* Set the custom rate (rate-code) for multicast data frames */
5281 WMI_VDEV_PARAM_MCAST_DATA_RATE,
5282 /* Tx multicast packet indicate Enable/Disable */
5283 WMI_VDEV_PARAM_MCAST_INDICATE,
5284 /* Tx DHCP packet indicate Enable/Disable */
5285 WMI_VDEV_PARAM_DHCP_INDICATE,
5286 /* Enable host inspection of Tx unicast packet to unknown destination */
5287 WMI_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
5289 /* The minimum amount of time AP begins to consider STA inactive */
5290 WMI_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
5292 /*
5293 * An associated STA is considered inactive when there is no recent
5294 * TX/RX activity and no downlink frames are buffered for it. Once a
5295 * STA exceeds the maximum idle inactive time, the AP will send an
5296 * 802.11 data-null as a keep alive to verify the STA is still
5297 * associated. If the STA does ACK the data-null, or if the data-null
5298 * is buffered and the STA does not retrieve it, the STA will be
5299 * considered unresponsive
5300 * (see WMI_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS).
5301 */
5302 WMI_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
5304 /*
5305 * An associated STA is considered unresponsive if there is no recent
5306 * TX/RX activity and downlink frames are buffered for it. Once a STA
5307 * exceeds the maximum unresponsive time, the AP will send a
5308 * WMI_STA_KICKOUT event to the host so the STA can be deleted.
5309 */
5310 WMI_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
5312 /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */
5313 WMI_VDEV_PARAM_AP_ENABLE_NAWDS,
5314 /* Enable/Disable RTS-CTS */
5315 WMI_VDEV_PARAM_ENABLE_RTSCTS,
5316 /* Enable TXBFee/er */
5317 WMI_VDEV_PARAM_TXBF,
5319 /* Set packet power save */
5320 WMI_VDEV_PARAM_PACKET_POWERSAVE,
5322 /*
5323 * Drops un-encrypted packets if eceived in an encrypted connection
5324 * otherwise forwards to host.
5325 */
5326 WMI_VDEV_PARAM_DROP_UNENCRY,
5328 /*
5329 * Set the encapsulation type for frames.
5330 */
5331 WMI_VDEV_PARAM_TX_ENCAP_TYPE,
5332 };
5334 /* the definition of different VDEV parameters */
5336 /* RTS Threshold */
5338 /* Fragmentation threshold */
5339 WMI_10X_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
5340 /* beacon interval in TUs */
5341 WMI_10X_VDEV_PARAM_BEACON_INTERVAL,
5342 /* Listen interval in TUs */
5343 WMI_10X_VDEV_PARAM_LISTEN_INTERVAL,
5344 /* multicast rate in Mbps */
5345 WMI_10X_VDEV_PARAM_MULTICAST_RATE,
5346 /* management frame rate in Mbps */
5347 WMI_10X_VDEV_PARAM_MGMT_TX_RATE,
5348 /* slot time (long vs short) */
5349 WMI_10X_VDEV_PARAM_SLOT_TIME,
5350 /* preamble (long vs short) */
5351 WMI_10X_VDEV_PARAM_PREAMBLE,
5352 /* SWBA time (time before tbtt in msec) */
5353 WMI_10X_VDEV_PARAM_SWBA_TIME,
5354 /* time period for updating VDEV stats */
5355 WMI_10X_VDEV_STATS_UPDATE_PERIOD,
5356 /* age out time in msec for frames queued for station in power save */
5357 WMI_10X_VDEV_PWRSAVE_AGEOUT_TIME,
5358 /*
5359 * Host SWBA interval (time in msec before tbtt for SWBA event
5360 * generation).
5361 */
5362 WMI_10X_VDEV_HOST_SWBA_INTERVAL,
5363 /* DTIM period (specified in units of num beacon intervals) */
5364 WMI_10X_VDEV_PARAM_DTIM_PERIOD,
5365 /*
5366 * scheduler air time limit for this VDEV. used by off chan
5367 * scheduler.
5368 */
5369 WMI_10X_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
5370 /* enable/dsiable WDS for this VDEV */
5371 WMI_10X_VDEV_PARAM_WDS,
5372 /* ATIM Window */
5373 WMI_10X_VDEV_PARAM_ATIM_WINDOW,
5374 /* BMISS max */
5375 WMI_10X_VDEV_PARAM_BMISS_COUNT_MAX,
5376 /* WMM enables/disabled */
5377 WMI_10X_VDEV_PARAM_FEATURE_WMM,
5378 /* Channel width */
5379 WMI_10X_VDEV_PARAM_CHWIDTH,
5380 /* Channel Offset */
5381 WMI_10X_VDEV_PARAM_CHEXTOFFSET,
5382 /* Disable HT Protection */
5383 WMI_10X_VDEV_PARAM_DISABLE_HTPROTECTION,
5384 /* Quick STA Kickout */
5385 WMI_10X_VDEV_PARAM_STA_QUICKKICKOUT,
5386 /* Rate to be used with Management frames */
5387 WMI_10X_VDEV_PARAM_MGMT_RATE,
5388 /* Protection Mode */
5389 WMI_10X_VDEV_PARAM_PROTECTION_MODE,
5390 /* Fixed rate setting */
5391 WMI_10X_VDEV_PARAM_FIXED_RATE,
5392 /* Short GI Enable/Disable */
5393 WMI_10X_VDEV_PARAM_SGI,
5394 /* Enable LDPC */
5395 WMI_10X_VDEV_PARAM_LDPC,
5396 /* Enable Tx STBC */
5397 WMI_10X_VDEV_PARAM_TX_STBC,
5398 /* Enable Rx STBC */
5399 WMI_10X_VDEV_PARAM_RX_STBC,
5400 /* Intra BSS forwarding */
5401 WMI_10X_VDEV_PARAM_INTRA_BSS_FWD,
5402 /* Setting Default xmit key for Vdev */
5403 WMI_10X_VDEV_PARAM_DEF_KEYID,
5404 /* NSS width */
5405 WMI_10X_VDEV_PARAM_NSS,
5406 /* Set the custom rate for the broadcast data frames */
5407 WMI_10X_VDEV_PARAM_BCAST_DATA_RATE,
5408 /* Set the custom rate (rate-code) for multicast data frames */
5409 WMI_10X_VDEV_PARAM_MCAST_DATA_RATE,
5410 /* Tx multicast packet indicate Enable/Disable */
5411 WMI_10X_VDEV_PARAM_MCAST_INDICATE,
5412 /* Tx DHCP packet indicate Enable/Disable */
5413 WMI_10X_VDEV_PARAM_DHCP_INDICATE,
5414 /* Enable host inspection of Tx unicast packet to unknown destination */
5415 WMI_10X_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
5417 /* The minimum amount of time AP begins to consider STA inactive */
5418 WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
5420 /*
5421 * An associated STA is considered inactive when there is no recent
5422 * TX/RX activity and no downlink frames are buffered for it. Once a
5423 * STA exceeds the maximum idle inactive time, the AP will send an
5424 * 802.11 data-null as a keep alive to verify the STA is still
5425 * associated. If the STA does ACK the data-null, or if the data-null
5426 * is buffered and the STA does not retrieve it, the STA will be
5427 * considered unresponsive
5428 * (see WMI_10X_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS).
5429 */
5430 WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
5432 /*
5433 * An associated STA is considered unresponsive if there is no recent
5434 * TX/RX activity and downlink frames are buffered for it. Once a STA
5435 * exceeds the maximum unresponsive time, the AP will send a
5436 * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted.
5437 */
5438 WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
5440 /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */
5441 WMI_10X_VDEV_PARAM_AP_ENABLE_NAWDS,
5443 WMI_10X_VDEV_PARAM_MCAST2UCAST_SET,
5444 /* Enable/Disable RTS-CTS */
5445 WMI_10X_VDEV_PARAM_ENABLE_RTSCTS,
5447 WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
5449 /* following are available as of firmware 10.2 */
5450 WMI_10X_VDEV_PARAM_TX_ENCAP_TYPE,
5451 WMI_10X_VDEV_PARAM_CABQ_MAXDUR,
5452 WMI_10X_VDEV_PARAM_MFPTEST_SET,
5453 WMI_10X_VDEV_PARAM_RTS_FIXED_RATE,
5454 WMI_10X_VDEV_PARAM_VHT_SGIMASK,
5455 WMI_10X_VDEV_PARAM_VHT80_RATEMASK,
5456 WMI_10X_VDEV_PARAM_TSF_INCREMENT,
5457 };
5461 WMI_10_4_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
5462 WMI_10_4_VDEV_PARAM_BEACON_INTERVAL,
5463 WMI_10_4_VDEV_PARAM_LISTEN_INTERVAL,
5464 WMI_10_4_VDEV_PARAM_MULTICAST_RATE,
5465 WMI_10_4_VDEV_PARAM_MGMT_TX_RATE,
5466 WMI_10_4_VDEV_PARAM_SLOT_TIME,
5467 WMI_10_4_VDEV_PARAM_PREAMBLE,
5468 WMI_10_4_VDEV_PARAM_SWBA_TIME,
5469 WMI_10_4_VDEV_STATS_UPDATE_PERIOD,
5470 WMI_10_4_VDEV_PWRSAVE_AGEOUT_TIME,
5471 WMI_10_4_VDEV_HOST_SWBA_INTERVAL,
5472 WMI_10_4_VDEV_PARAM_DTIM_PERIOD,
5473 WMI_10_4_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
5474 WMI_10_4_VDEV_PARAM_WDS,
5475 WMI_10_4_VDEV_PARAM_ATIM_WINDOW,
5476 WMI_10_4_VDEV_PARAM_BMISS_COUNT_MAX,
5477 WMI_10_4_VDEV_PARAM_BMISS_FIRST_BCNT,
5478 WMI_10_4_VDEV_PARAM_BMISS_FINAL_BCNT,
5479 WMI_10_4_VDEV_PARAM_FEATURE_WMM,
5480 WMI_10_4_VDEV_PARAM_CHWIDTH,
5481 WMI_10_4_VDEV_PARAM_CHEXTOFFSET,
5482 WMI_10_4_VDEV_PARAM_DISABLE_HTPROTECTION,
5483 WMI_10_4_VDEV_PARAM_STA_QUICKKICKOUT,
5484 WMI_10_4_VDEV_PARAM_MGMT_RATE,
5485 WMI_10_4_VDEV_PARAM_PROTECTION_MODE,
5486 WMI_10_4_VDEV_PARAM_FIXED_RATE,
5487 WMI_10_4_VDEV_PARAM_SGI,
5488 WMI_10_4_VDEV_PARAM_LDPC,
5489 WMI_10_4_VDEV_PARAM_TX_STBC,
5490 WMI_10_4_VDEV_PARAM_RX_STBC,
5491 WMI_10_4_VDEV_PARAM_INTRA_BSS_FWD,
5492 WMI_10_4_VDEV_PARAM_DEF_KEYID,
5493 WMI_10_4_VDEV_PARAM_NSS,
5494 WMI_10_4_VDEV_PARAM_BCAST_DATA_RATE,
5495 WMI_10_4_VDEV_PARAM_MCAST_DATA_RATE,
5496 WMI_10_4_VDEV_PARAM_MCAST_INDICATE,
5497 WMI_10_4_VDEV_PARAM_DHCP_INDICATE,
5498 WMI_10_4_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
5499 WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
5500 WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
5501 WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
5502 WMI_10_4_VDEV_PARAM_AP_ENABLE_NAWDS,
5503 WMI_10_4_VDEV_PARAM_MCAST2UCAST_SET,
5504 WMI_10_4_VDEV_PARAM_ENABLE_RTSCTS,
5505 WMI_10_4_VDEV_PARAM_RC_NUM_RETRIES,
5506 WMI_10_4_VDEV_PARAM_TXBF,
5507 WMI_10_4_VDEV_PARAM_PACKET_POWERSAVE,
5508 WMI_10_4_VDEV_PARAM_DROP_UNENCRY,
5509 WMI_10_4_VDEV_PARAM_TX_ENCAP_TYPE,
5510 WMI_10_4_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
5511 WMI_10_4_VDEV_PARAM_CABQ_MAXDUR,
5512 WMI_10_4_VDEV_PARAM_MFPTEST_SET,
5513 WMI_10_4_VDEV_PARAM_RTS_FIXED_RATE,
5514 WMI_10_4_VDEV_PARAM_VHT_SGIMASK,
5515 WMI_10_4_VDEV_PARAM_VHT80_RATEMASK,
5516 WMI_10_4_VDEV_PARAM_EARLY_RX_ADJUST_ENABLE,
5517 WMI_10_4_VDEV_PARAM_EARLY_RX_TGT_BMISS_NUM,
5518 WMI_10_4_VDEV_PARAM_EARLY_RX_BMISS_SAMPLE_CYCLE,
5519 WMI_10_4_VDEV_PARAM_EARLY_RX_SLOP_STEP,
5520 WMI_10_4_VDEV_PARAM_EARLY_RX_INIT_SLOP,
5521 WMI_10_4_VDEV_PARAM_EARLY_RX_ADJUST_PAUSE,
5522 WMI_10_4_VDEV_PARAM_PROXY_STA,
5523 WMI_10_4_VDEV_PARAM_MERU_VC,
5524 WMI_10_4_VDEV_PARAM_RX_DECAP_TYPE,
5525 WMI_10_4_VDEV_PARAM_BW_NSS_RATEMASK,
5526 WMI_10_4_VDEV_PARAM_SENSOR_AP,
5527 WMI_10_4_VDEV_PARAM_BEACON_RATE,
5528 WMI_10_4_VDEV_PARAM_DTIM_ENABLE_CTS,
5529 WMI_10_4_VDEV_PARAM_STA_KICKOUT,
5530 WMI_10_4_VDEV_PARAM_CAPABILITIES,
5531 WMI_10_4_VDEV_PARAM_TSF_INCREMENT,
5532 WMI_10_4_VDEV_PARAM_RX_FILTER,
5533 WMI_10_4_VDEV_PARAM_MGMT_TX_POWER,
5534 WMI_10_4_VDEV_PARAM_ATF_SSID_SCHED_POLICY,
5535 WMI_10_4_VDEV_PARAM_DISABLE_DYN_BW_RTS,
5536 WMI_10_4_VDEV_PARAM_TSF_DECREMENT,
5537 WMI_10_4_VDEV_PARAM_SELFGEN_FIXED_RATE,
5538 WMI_10_4_VDEV_PARAM_AMPDU_SUBFRAME_SIZE_PER_AC,
5539 WMI_10_4_VDEV_PARAM_NSS_VHT160,
5540 WMI_10_4_VDEV_PARAM_NSS_VHT80_80,
5541 WMI_10_4_VDEV_PARAM_AMSDU_SUBFRAME_SIZE_PER_AC,
5542 WMI_10_4_VDEV_PARAM_DISABLE_CABQ,
5543 WMI_10_4_VDEV_PARAM_SIFS_TRIGGER_RATE,
5544 WMI_10_4_VDEV_PARAM_TX_POWER,
5545 WMI_10_4_VDEV_PARAM_ENABLE_DISABLE_RTT_RESPONDER_ROLE,
5546 WMI_10_4_VDEV_PARAM_DISABLE_4_ADDR_SRC_LRN,
5547 };
5549 #define WMI_VDEV_DISABLE_4_ADDR_SRC_LRN 1
5551 #define WMI_VDEV_PARAM_TXBF_SU_TX_BFEE BIT(0)
5552 #define WMI_VDEV_PARAM_TXBF_MU_TX_BFEE BIT(1)
5553 #define WMI_VDEV_PARAM_TXBF_SU_TX_BFER BIT(2)
5554 #define WMI_VDEV_PARAM_TXBF_MU_TX_BFER BIT(3)
5556 #define WMI_TXBF_STS_CAP_OFFSET_LSB 4
5557 #define WMI_TXBF_STS_CAP_OFFSET_MASK 0x70
5558 #define WMI_TXBF_CONF_IMPLICIT_BF BIT(7)
5559 #define WMI_BF_SOUND_DIM_OFFSET_LSB 8
5560 #define WMI_BF_SOUND_DIM_OFFSET_MASK 0xf00
5562 /* slot time long */
5563 #define WMI_VDEV_SLOT_TIME_LONG 0x1
5564 /* slot time short */
5565 #define WMI_VDEV_SLOT_TIME_SHORT 0x2
5566 /* preablbe long */
5567 #define WMI_VDEV_PREAMBLE_LONG 0x1
5568 /* preablbe short */
5569 #define WMI_VDEV_PREAMBLE_SHORT 0x2
5573 WMI_VDEV_RESP_RESTART_EVENT,
5574 };
5577 __le32 vdev_id;
5578 __le32 req_id;
5580 __le32 status;
5584 /* unique id identifying the VDEV, generated by the caller */
5585 __le32 vdev_id;
5589 /* unique id identifying the VDEV, generated by the caller */
5590 __le32 vdev_id;
5594 /* unique id identifying the VDEV, generated by the caller */
5595 __le32 vdev_id;
5598 /*
5599 * common structure used for simple events
5600 * (stopped, resume_req, standby response)
5601 */
5603 /* unique id identifying the VDEV, generated by the caller */
5604 __le32 vdev_id;
5607 /* VDEV start response status codes */
5608 /* VDEV successfully started */
5609 #define WMI_INIFIED_VDEV_START_RESPONSE_STATUS_SUCCESS 0x0
5611 /* requested VDEV not found */
5612 #define WMI_INIFIED_VDEV_START_RESPONSE_INVALID_VDEVID 0x1
5614 /* unsupported VDEV combination */
5615 #define WMI_INIFIED_VDEV_START_RESPONSE_NOT_SUPPORTED 0x2
5617 /* TODO: please add more comments if you have in-depth information */
5619 __le32 vdev_id;
5621 /* number of fft samples to send (0 for infinite) */
5622 __le32 scan_count;
5623 __le32 scan_period;
5624 __le32 scan_priority;
5626 /* number of bins in the FFT: 2^(fft_size - bin_scale) */
5627 __le32 scan_fft_size;
5628 __le32 scan_gc_ena;
5629 __le32 scan_restart_ena;
5630 __le32 scan_noise_floor_ref;
5631 __le32 scan_init_delay;
5632 __le32 scan_nb_tone_thr;
5633 __le32 scan_str_bin_thr;
5634 __le32 scan_wb_rpt_mode;
5635 __le32 scan_rssi_rpt_mode;
5636 __le32 scan_rssi_thr;
5637 __le32 scan_pwr_format;
5639 /* rpt_mode: Format of FFT report to software for spectral scan
5640 * triggered FFTs:
5641 * 0: No FFT report (only spectral scan summary report)
5642 * 1: 2-dword summary of metrics for each completed FFT + spectral
5643 * scan summary report
5644 * 2: 2-dword summary of metrics for each completed FFT +
5645 * 1x- oversampled bins(in-band) per FFT + spectral scan summary
5646 * report
5647 * 3: 2-dword summary of metrics for each completed FFT +
5648 * 2x- oversampled bins (all) per FFT + spectral scan summary
5649 */
5650 __le32 scan_rpt_mode;
5651 __le32 scan_bin_scale;
5652 __le32 scan_dbm_adj;
5653 __le32 scan_chn_mask;
5657 u32 vdev_id;
5658 u32 scan_count;
5659 u32 scan_period;
5660 u32 scan_priority;
5661 u32 scan_fft_size;
5662 u32 scan_gc_ena;
5663 u32 scan_restart_ena;
5664 u32 scan_noise_floor_ref;
5665 u32 scan_init_delay;
5666 u32 scan_nb_tone_thr;
5667 u32 scan_str_bin_thr;
5668 u32 scan_wb_rpt_mode;
5669 u32 scan_rssi_rpt_mode;
5670 u32 scan_rssi_thr;
5671 u32 scan_pwr_format;
5672 u32 scan_rpt_mode;
5673 u32 scan_bin_scale;
5674 u32 scan_dbm_adj;
5675 u32 scan_chn_mask;
5676 };
5678 #define WMI_SPECTRAL_ENABLE_DEFAULT 0
5679 #define WMI_SPECTRAL_COUNT_DEFAULT 0
5680 #define WMI_SPECTRAL_PERIOD_DEFAULT 35
5681 #define WMI_SPECTRAL_PRIORITY_DEFAULT 1
5682 #define WMI_SPECTRAL_FFT_SIZE_DEFAULT 7
5683 #define WMI_SPECTRAL_GC_ENA_DEFAULT 1
5684 #define WMI_SPECTRAL_RESTART_ENA_DEFAULT 0
5685 #define WMI_SPECTRAL_NOISE_FLOOR_REF_DEFAULT -96
5686 #define WMI_SPECTRAL_INIT_DELAY_DEFAULT 80
5687 #define WMI_SPECTRAL_NB_TONE_THR_DEFAULT 12
5688 #define WMI_SPECTRAL_STR_BIN_THR_DEFAULT 8
5689 #define WMI_SPECTRAL_WB_RPT_MODE_DEFAULT 0
5690 #define WMI_SPECTRAL_RSSI_RPT_MODE_DEFAULT 0
5691 #define WMI_SPECTRAL_RSSI_THR_DEFAULT 0xf0
5692 #define WMI_SPECTRAL_PWR_FORMAT_DEFAULT 0
5693 #define WMI_SPECTRAL_RPT_MODE_DEFAULT 2
5694 #define WMI_SPECTRAL_BIN_SCALE_DEFAULT 1
5695 #define WMI_SPECTRAL_DBM_ADJ_DEFAULT 1
5696 #define WMI_SPECTRAL_CHN_MASK_DEFAULT 1
5699 __le32 vdev_id;
5700 __le32 trigger_cmd;
5701 __le32 enable_cmd;
5704 #define WMI_SPECTRAL_TRIGGER_CMD_TRIGGER 1
5705 #define WMI_SPECTRAL_TRIGGER_CMD_CLEAR 2
5706 #define WMI_SPECTRAL_ENABLE_CMD_ENABLE 1
5707 #define WMI_SPECTRAL_ENABLE_CMD_DISABLE 2
5709 /* Beacon processing related command and event structures */
5711 __le32 vdev_id;
5712 __le32 tx_rate;
5713 __le32 tx_power;
5714 __le32 bcn_len;
5723 u32 vdev_id;
5724 u32 tx_rate;
5725 u32 tx_power;
5726 u32 bcn_len;
5728 };
5733 };
5735 /* TODO: It is unclear why "no antenna" works while any other seemingly valid
5736 * chainmask yields no beacons on the air at all.
5737 */
5738 #define WMI_BCN_TX_REF_DEF_ANTENNA 0
5741 __le32 vdev_id;
5742 __le32 data_len;
5743 /* physical address of the frame - dma pointer */
5744 __le32 data_ptr;
5745 /* id for host to track */
5746 __le32 msdu_id;
5747 /* frame ctrl to setup PPDU desc */
5748 __le32 frame_control;
5749 /* to control CABQ traffic: WMI_BCN_TX_REF_FLAG_ */
5750 __le32 flags;
5751 /* introduced in 10.2 */
5752 __le32 antenna_mask;
5755 /* Beacon filter */
5763 /* Filter ID */
5764 __le32 bcn_filter_id;
5765 /* Filter type - wmi_bcn_filter */
5766 __le32 bcn_filter;
5767 /* Buffer len */
5768 __le32 bcn_filter_len;
5769 /* Filter info (threshold, BSSID, RSSI) */
5773 /* Capabilities and IEs to be passed to firmware */
5775 /* Capabilities */
5776 __le32 caps;
5777 /* ERP info */
5778 __le32 erp;
5779 /* Advanced capabilities */
5780 /* HT capabilities */
5781 /* HT Info */
5782 /* ibss_dfs */
5783 /* wpa Info */
5784 /* rsn Info */
5785 /* rrm info */
5786 /* ath_ext */
5787 /* app IE */
5791 /* unique id identifying the VDEV, generated by the caller */
5792 __le32 vdev_id;
5793 /* TIM IE offset from the beginning of the template. */
5794 __le32 tim_ie_offset;
5795 /* beacon probe capabilities and IEs */
5797 /* beacon buffer length */
5798 __le32 buf_len;
5799 /* variable length data */
5804 /* unique id identifying the VDEV, generated by the caller */
5805 __le32 vdev_id;
5806 /* beacon probe capabilities and IEs */
5808 /* beacon buffer length */
5809 __le32 buf_len;
5810 /* Variable length data */
5815 /* enable power save for the given STA VDEV */
5817 /* disable power save for a given STA VDEV */
5819 };
5822 /* unique id identifying the VDEV, generated by the caller */
5823 __le32 vdev_id;
5825 /*
5826 * Power save mode
5827 * (see enum wmi_sta_ps_mode)
5828 */
5829 __le32 sta_ps_mode;
5835 };
5838 __le32 vdev_id;
5839 __le32 csa_offload_enable;
5843 __le32 vdev_id;
5847 /*
5848 * This parameter controls the policy for retrieving frames from AP while the
5849 * STA is in sleep state.
5850 *
5851 * Only takes affect if the sta_ps_mode is enabled
5852 */
5854 /*
5855 * Wake up when ever there is an RX activity on the VDEV. In this mode
5856 * the Power save SM(state machine) will come out of sleep by either
5857 * sending null frame (or) a data frame (with PS==0) in response to TIM
5858 * bit set in the received beacon frame from AP.
5859 */
5862 /*
5863 * Here the power save state machine will not wakeup in response to TIM
5864 * bit, instead it will send a PSPOLL (or) UASPD trigger based on UAPSD
5865 * configuration setup by WMISET_PS_SET_UAPSD WMI command. When all
5866 * access categories are delivery-enabled, the station will send a
5867 * UAPSD trigger frame, otherwise it will send a PS-Poll.
5868 */
5870 };
5872 /*
5873 * Number of tx frames/beacon that cause the power save SM to wake up.
5874 *
5875 * Value 1 causes the SM to wake up for every TX. Value 0 has a special
5876 * meaning, It will cause the SM to never wake up. This is useful if you want
5877 * to keep the system to sleep all the time for some kind of test mode . host
5878 * can change this parameter any time. It will affect at the next tx frame.
5879 */
5884 /*
5885 * Values greater than one indicate that many TX attempts per beacon
5886 * interval before the STA will wake up
5887 */
5888 };
5890 /*
5891 * The maximum number of PS-Poll frames the FW will send in response to
5892 * traffic advertised in TIM before waking up (by sending a null frame with PS
5893 * = 0). Value 0 has a special meaning: there is no maximum count and the FW
5894 * will send as many PS-Poll as are necessary to retrieve buffered BU. This
5895 * parameter is used when the RX wake policy is
5896 * WMI_STA_PS_RX_WAKE_POLICY_POLL_UAPSD and ignored when the RX wake
5897 * policy is WMI_STA_PS_RX_WAKE_POLICY_WAKE.
5898 */
5901 /*
5902 * Values greater than 0 indicate the maximum numer of PS-Poll frames
5903 * FW will send before waking up.
5904 */
5906 /* When u-APSD is enabled the firmware will be very reluctant to exit
5907 * STA PS. This could result in very poor Rx performance with STA doing
5908 * PS-Poll for each and every buffered frame. This value is a bit
5909 * arbitrary.
5910 */
5912 };
5914 /*
5915 * This will include the delivery and trigger enabled state for every AC.
5916 * This is the negotiated state with AP. The host MLME needs to set this based
5917 * on AP capability and the state Set in the association request by the
5918 * station MLME.Lower 8 bits of the value specify the UAPSD configuration.
5919 */
5920 #define WMI_UAPSD_AC_TYPE_DELI 0
5921 #define WMI_UAPSD_AC_TYPE_TRIG 1
5923 #define WMI_UAPSD_AC_BIT_MASK(ac, type) \
5924 (type == WMI_UAPSD_AC_TYPE_DELI ? 1 << (ac << 1) : 1 << ((ac << 1) + 1))
5935 };
5937 #define WMI_STA_UAPSD_MAX_INTERVAL_MSEC UINT_MAX
5940 __le32 wmm_ac;
5941 __le32 user_priority;
5942 __le32 service_interval;
5943 __le32 suspend_interval;
5944 __le32 delay_interval;
5945 };
5948 __le32 vdev_id;
5950 __le32 num_ac;
5951 };
5954 u32 wmm_ac;
5955 u32 user_priority;
5956 u32 service_interval;
5957 u32 suspend_interval;
5958 u32 delay_interval;
5959 };
5962 /*
5963 * Controls how frames are retrievd from AP while STA is sleeping
5964 *
5965 * (see enum wmi_sta_ps_param_rx_wake_policy)
5966 */
5969 /*
5970 * The STA will go active after this many TX
5971 *
5972 * (see enum wmi_sta_ps_param_tx_wake_threshold)
5973 */
5976 /*
5977 * Number of PS-Poll to send before STA wakes up
5978 *
5979 * (see enum wmi_sta_ps_param_pspoll_count)
5980 *
5981 */
5984 /*
5985 * TX/RX inactivity time in msec before going to sleep.
5986 *
5987 * The power save SM will monitor tx/rx activity on the VDEV, if no
5988 * activity for the specified msec of the parameter the Power save
5989 * SM will go to sleep.
5990 */
5993 /*
5994 * Set uapsd configuration.
5995 *
5996 * (see enum wmi_sta_ps_param_uapsd)
5997 */
5999 };
6002 __le32 vdev_id;
6004 __le32 param_value;
6007 /* No MIMO power save */
6008 #define WMI_STA_MIMO_PS_MODE_DISABLE
6009 /* mimo powersave mode static*/
6010 #define WMI_STA_MIMO_PS_MODE_STATIC
6011 /* mimo powersave mode dynamic */
6012 #define WMI_STA_MIMO_PS_MODE_DYNAMIC
6015 /* unique id identifying the VDEV, generated by the caller */
6016 __le32 vdev_id;
6017 /* mimo powersave mode as defined above */
6018 __le32 mimo_pwrsave_mode;
6021 /* U-APSD configuration of peer station from (re)assoc request and TSPECs */
6031 };
6033 /* U-APSD maximum service period of peer station */
6039 MAX_WMI_AP_PS_PEER_PARAM_MAX_SP,
6040 };
6042 /*
6043 * AP power save parameter
6044 * Set a power save specific parameter for a peer station
6045 */
6047 /* Set uapsd configuration for a given peer.
6048 *
6049 * Include the delivery and trigger enabled state for every AC.
6050 * The host MLME needs to set this based on AP capability and stations
6051 * request Set in the association request received from the station.
6052 *
6053 * Lower 8 bits of the value specify the UAPSD configuration.
6054 *
6055 * (see enum wmi_ap_ps_param_uapsd)
6056 * The default value is 0.
6057 */
6060 /*
6061 * Set the service period for a UAPSD capable station
6062 *
6063 * The service period from wme ie in the (re)assoc request frame.
6064 *
6065 * (see enum wmi_ap_ps_peer_param_max_sp)
6066 */
6069 /* Time in seconds for aging out buffered frames for STA in PS */
6071 };
6074 /* unique id identifying the VDEV, generated by the caller */
6075 __le32 vdev_id;
6077 /* peer MAC address */
6080 /* AP powersave param (see enum wmi_ap_ps_peer_param) */
6081 __le32 param_id;
6083 /* AP powersave param value */
6084 __le32 param_value;
6087 /* 128 clients = 4 words */
6088 #define WMI_TIM_BITMAP_ARRAY_SIZE 4
6091 __le32 tim_len;
6092 __le32 tim_mcast;
6094 __le32 tim_changed;
6095 __le32 tim_num_ps_pending;
6099 __le32 tim_len;
6100 __le32 tim_mcast;
6102 __le32 tim_changed;
6103 __le32 tim_num_ps_pending;
6106 /* Maximum number of NOA Descriptors supported */
6107 #define WMI_P2P_MAX_NOA_DESCRIPTORS 4
6108 #define WMI_P2P_OPPPS_ENABLE_BIT BIT(0)
6109 #define WMI_P2P_OPPPS_CTWINDOW_OFFSET 1
6110 #define WMI_P2P_NOA_CHANGED_BIT BIT(0)
6113 /* Bit 0 - Flag to indicate an update in NOA schedule
6114 * Bits 7-1 - Reserved
6115 */
6116 u8 changed;
6117 /* NOA index */
6118 u8 index;
6119 /* Bit 0 - Opp PS state of the AP
6120 * Bits 1-7 - Ctwindow in TUs
6121 */
6122 u8 ctwindow_oppps;
6123 /* Number of NOA descriptors */
6124 u8 num_descriptors;
6135 __le32 vdev_map;
6141 /* The 10.2.4 FW doesn't have p2p NOA info */
6145 __le32 vdev_map;
6149 /* 16 words = 512 client + 1 word = for guard */
6150 #define WMI_10_4_TIM_BITMAP_ARRAY_SIZE 17
6153 __le32 tim_len;
6154 __le32 tim_mcast;
6156 __le32 tim_changed;
6157 __le32 tim_num_ps_pending;
6160 #define WMI_10_4_P2P_MAX_NOA_DESCRIPTORS 1
6163 /* Bit 0 - Flag to indicate an update in NOA schedule
6164 * Bits 7-1 - Reserved
6165 */
6166 u8 changed;
6167 /* NOA index */
6168 u8 index;
6169 /* Bit 0 - Opp PS state of the AP
6170 * Bits 1-7 - Ctwindow in TUs
6171 */
6172 u8 ctwindow_oppps;
6173 /* Number of NOA descriptors */
6174 u8 num_descriptors;
6176 struct wmi_p2p_noa_descriptor
6186 __le32 vdev_map;
6190 #define WMI_MAX_AP_VDEV 16
6193 __le32 vdev_map;
6198 __le32 vdev_id;
6200 __le32 peer_type;
6207 };
6210 __le32 vdev_id;
6215 __le32 vdev_id;
6217 __le32 peer_tid_bitmap;
6221 /*
6222 * rate mode . 0: disable fixed rate (auto rate)
6223 * 1: legacy (non 11n) rate specified as ieee rate 2*Mbps
6224 * 2: ht20 11n rate specified as mcs index
6225 * 3: ht40 11n rate specified as mcs index
6226 */
6227 __le32 rate_mode;
6228 /*
6229 * 4 rate values for 4 rate series. series 0 is stored in byte 0 (LSB)
6230 * and series 3 is stored at byte 3 (MSB)
6231 */
6232 __le32 rate_series;
6233 /*
6234 * 4 retry counts for 4 rate series. retry count for rate 0 is stored
6235 * in byte 0 (LSB) and retry count for rate 3 is stored at byte 3
6236 * (MSB)
6237 */
6238 __le32 rate_retries;
6242 /* unique id identifying the VDEV, generated by the caller */
6243 __le32 vdev_id;
6244 /* peer MAC address */
6246 /* fixed rate */
6250 #define WMI_MGMT_TID 17
6253 /* unique id identifying the VDEV, generated by the caller */
6254 __le32 vdev_id;
6255 /* peer MAC address */
6260 /* unique id identifying the VDEV, generated by the caller */
6261 __le32 vdev_id;
6262 /* peer MAC address */
6264 /* Tid number */
6265 __le32 tid;
6266 /* Buffer/Window size*/
6267 __le32 buffersize;
6271 /* unique id identifying the VDEV, generated by the caller */
6272 __le32 vdev_id;
6273 /* peer MAC address */
6275 /* Tid number */
6276 __le32 tid;
6277 /* Is Initiator */
6278 __le32 initiator;
6279 /* Reason code */
6280 __le32 reasoncode;
6284 /* unique id identifying the vdev, generated by the caller */
6285 __le32 vdev_id;
6286 /* peer mac address */
6288 /* Tid number */
6289 __le32 tid;
6290 /* status code */
6291 __le32 statuscode;
6295 /* unique id identifying the vdev, generated by the caller */
6296 __le32 vdev_id;
6297 /* peer mac address */
6299 /* Tid number */
6300 __le32 tid;
6307 };
6314 };
6328 };
6331 __le32 vdev_id;
6333 __le32 param_id;
6334 __le32 param_value;
6337 #define MAX_SUPPORTED_RATES 128
6340 /* total number of rates */
6341 __le32 num_rates;
6342 /*
6343 * rates (each 8bit value) packed into a 32 bit word.
6344 * the rates are filled from least significant byte to most
6345 * significant byte.
6346 */
6353 };
6355 /*
6356 * NOTE: It would bea good idea to represent the Tx MCS
6357 * info in one word and Rx in another word. This is split
6358 * into multiple words for convenience
6359 */
6368 u32 rx_max_rate;
6369 u32 rx_mcs_set;
6370 u32 tx_max_rate;
6371 u32 tx_mcs_set;
6372 };
6375 /* peer MAC address */
6377 /* legacy rate set */
6379 /* ht rate set */
6384 /* unique id identifying the VDEV, generated by the caller */
6385 __le32 vdev_id;
6386 /* peer MAC address */
6388 __le32 callback_enable;
6392 u32 auth;
6393 u32 qos;
6394 u32 need_ptk_4_way;
6395 u32 need_gtk_2_way;
6396 u32 apsd;
6397 u32 ht;
6398 u32 bw40;
6399 u32 stbc;
6400 u32 ldbc;
6401 u32 dyn_mimops;
6402 u32 static_mimops;
6403 u32 spatial_mux;
6404 u32 vht;
6405 u32 bw80;
6406 u32 vht_2g;
6407 u32 pmf;
6408 u32 bw160;
6409 };
6429 };
6447 };
6467 };
6469 /*
6470 * Peer rate capabilities.
6471 *
6472 * This is of interest to the ratecontrol
6473 * module which resides in the firmware. The bit definitions are
6474 * consistent with that defined in if_athrate.c.
6475 */
6476 #define WMI_RC_DS_FLAG 0x01
6477 #define WMI_RC_CW40_FLAG 0x02
6478 #define WMI_RC_SGI_FLAG 0x04
6479 #define WMI_RC_HT_FLAG 0x08
6480 #define WMI_RC_RTSCTS_FLAG 0x10
6481 #define WMI_RC_TX_STBC_FLAG 0x20
6482 #define WMI_RC_RX_STBC_FLAG 0xC0
6483 #define WMI_RC_RX_STBC_FLAG_S 6
6484 #define WMI_RC_WEP_TKIP_FLAG 0x100
6485 #define WMI_RC_TS_FLAG 0x200
6486 #define WMI_RC_UAPSD_FLAG 0x400
6488 /* Maximum listen interval supported by hw in units of beacon interval */
6489 #define ATH10K_MAX_HW_LISTEN_INTERVAL 5
6493 __le32 vdev_id;
6496 __le32 peer_flags;
6498 __le32 peer_listen_intval;
6499 __le32 peer_ht_caps;
6500 __le32 peer_max_mpdu;
6502 __le32 peer_rate_caps;
6506 __le32 peer_vht_caps;
6507 __le32 peer_phymode;
6509 };
6514 /* HT Operation Element of the peer. Five bytes packed in 2
6515 * INT32 array and filled from lsb to msb.
6516 */
6524 #define WMI_PEER_ASSOC_INFO0_MAX_MCS_IDX_LSB 0
6525 #define WMI_PEER_ASSOC_INFO0_MAX_MCS_IDX_MASK 0x0f
6526 #define WMI_PEER_ASSOC_INFO0_MAX_NSS_LSB 4
6527 #define WMI_PEER_ASSOC_INFO0_MAX_NSS_MASK 0xf0
6534 /* NSS Mapping to FW */
6535 #define WMI_PEER_NSS_MAP_ENABLE BIT(31)
6536 #define WMI_PEER_NSS_160MHZ_MASK GENMASK(2, 0)
6537 #define WMI_PEER_NSS_80_80MHZ_MASK GENMASK(5, 3)
6541 __le32 peer_bw_rxnss_override;
6546 u32 vdev_id;
6548 u16 peer_aid;
6550 u16 peer_caps;
6551 u32 peer_listen_intval;
6552 u32 peer_ht_caps;
6553 u32 peer_max_mpdu;
6558 u32 peer_num_spatial_streams;
6559 u32 peer_vht_caps;
6562 u32 peer_bw_rxnss_override;
6563 };
6566 /* peer MAC address */
6568 /* wds MAC addr */
6573 /* wds MAC addr */
6578 /* peer MAC address */
6582 /*
6583 * Channel info WMI event
6584 */
6586 __le32 err_code;
6587 __le32 freq;
6588 __le32 cmd_flags;
6589 __le32 noise_floor;
6590 __le32 rx_clear_count;
6591 __le32 cycle_count;
6595 __le32 err_code;
6596 __le32 freq;
6597 __le32 cmd_flags;
6598 __le32 noise_floor;
6599 __le32 rx_clear_count;
6600 __le32 cycle_count;
6601 __le32 chan_tx_pwr_range;
6602 __le32 chan_tx_pwr_tp;
6603 __le32 rx_frame_count;
6610 #define WMI_CHAN_INFO_FLAG_COMPLETE BIT(0)
6611 #define WMI_CHAN_INFO_FLAG_PRE_COMPLETE BIT(1)
6613 /* Beacon filter wmi command info */
6614 #define BCN_FLT_MAX_SUPPORTED_IES 256
6615 #define BCN_FLT_MAX_ELEMS_IE_LIST (BCN_FLT_MAX_SUPPORTED_IES / 32)
6618 __le32 vdev_id;
6619 __le32 bss_bcnsdropped;
6620 __le32 bss_bcnsdelivered;
6624 __le32 bcns_dropped;
6625 __le32 bcns_delivered;
6626 __le32 activefilters;
6631 u32 vdev_id;
6638 };
6640 #define WMI_STA_KEEPALIVE_INTERVAL_DISABLE 0
6642 /* Firmware crashes if keepalive interval exceeds this limit */
6643 #define WMI_STA_KEEPALIVE_INTERVAL_MAX_SECONDS 0xffff
6645 /* note: ip4 addresses are in network byte order, i.e. big endian */
6647 __be32 src_ip4_addr;
6648 __be32 dest_ip4_addr;
6653 __le32 vdev_id;
6654 __le32 enabled;
6661 u32 vdev_id;
6662 u32 enabled;
6663 u32 method;
6664 u32 interval;
6665 __be32 src_ip4_addr;
6666 __be32 dest_ip4_addr;
6668 };
6672 WMI_FORCE_FW_HANG_NO_DETECT,
6673 WMI_FORCE_FW_HANG_CTRL_EP_FULL,
6674 WMI_FORCE_FW_HANG_EMPTY_POINT,
6675 WMI_FORCE_FW_HANG_STACK_OVERFLOW,
6676 WMI_FORCE_FW_HANG_INFINITE_LOOP,
6677 };
6679 #define WMI_FORCE_FW_HANG_RANDOM_TIME 0xFFFFFFFF
6682 __le32 type;
6683 __le32 delay_ms;
6688 WMI_RST_MODE_WARM_RESET,
6689 WMI_RST_MODE_COLD_RESET,
6690 WMI_RST_MODE_WARM_RESET_RESTORE_CAL,
6691 WMI_RST_MODE_COLD_RESET_RESTORE_CAL,
6692 WMI_RST_MODE_MAX,
6693 };
6700 };
6702 /* VAP ids to enable dbglog */
6703 #define ATH10K_DBGLOG_CFG_VAP_LOG_LSB 0
6704 #define ATH10K_DBGLOG_CFG_VAP_LOG_MASK 0x0000ffff
6706 /* to enable dbglog in the firmware */
6707 #define ATH10K_DBGLOG_CFG_REPORTING_ENABLE_LSB 16
6708 #define ATH10K_DBGLOG_CFG_REPORTING_ENABLE_MASK 0x00010000
6710 /* timestamp resolution */
6711 #define ATH10K_DBGLOG_CFG_RESOLUTION_LSB 17
6712 #define ATH10K_DBGLOG_CFG_RESOLUTION_MASK 0x000E0000
6714 /* number of queued messages before sending them to the host */
6715 #define ATH10K_DBGLOG_CFG_REPORT_SIZE_LSB 20
6716 #define ATH10K_DBGLOG_CFG_REPORT_SIZE_MASK 0x0ff00000
6718 /*
6719 * Log levels to enable. This defines the minimum level to enable, this is
6720 * not a bitmask. See enum ath10k_dbglog_level for the values.
6721 */
6722 #define ATH10K_DBGLOG_CFG_LOG_LVL_LSB 28
6723 #define ATH10K_DBGLOG_CFG_LOG_LVL_MASK 0x70000000
6725 /*
6726 * Note: this is a cleaned up version of a struct firmware uses. For
6727 * example, config_valid was hidden inside an array.
6728 */
6730 /* bitmask to hold mod id config*/
6731 __le32 module_enable;
6733 /* see ATH10K_DBGLOG_CFG_ */
6734 __le32 config_enable;
6736 /* mask of module id bits to be changed */
6737 __le32 module_valid;
6739 /* mask of config bits to be changed, see ATH10K_DBGLOG_CFG_ */
6740 __le32 config_valid;
6744 /* bitmask to hold mod id config*/
6745 __le64 module_enable;
6747 /* see ATH10K_DBGLOG_CFG_ */
6748 __le32 config_enable;
6750 /* mask of module id bits to be changed */
6751 __le64 module_valid;
6753 /* mask of config bits to be changed, see ATH10K_DBGLOG_CFG_ */
6754 __le32 config_valid;
6764 /* keep last */
6765 WMI_ROAM_REASON_MAX,
6766 };
6769 __le32 vdev_id;
6770 __le32 reason;
6773 #define ATH10K_FRAGMT_THRESHOLD_MIN 540
6774 #define ATH10K_FRAGMT_THRESHOLD_MAX 2346
6776 #define WMI_MAX_EVENT 0x1000
6777 /* Maximum number of pending TXed WMI packets */
6778 #define WMI_SKB_HEADROOM sizeof(struct wmi_cmd_hdr)
6780 /* By default disable power save for IBSS */
6781 #define ATH10K_DEFAULT_ATIM 0
6783 #define WMI_MAX_MEM_REQS 16
6789 __le32 scan_req_id;
6790 __le32 scan_id;
6791 __le32 vdev_id;
6792 };
6795 u32 desc_id;
6796 u32 status;
6797 u32 ppdu_id;
6799 };
6802 __le32 desc_id;
6803 __le32 status;
6804 __le32 pdev_id;
6805 __le32 ppdu_id;
6806 __le32 ack_rssi;
6807 };
6810 __le32 num_reports;
6815 };
6818 __le32 vdev_id;
6820 };
6822 #define WMI_MGMT_RX_NUM_RSSI 4
6824 __le32 channel;
6825 __le32 snr;
6826 __le32 rate;
6827 __le32 phy_mode;
6828 __le32 buf_len;
6832 };
6835 __le32 err_code;
6836 __le32 freq;
6837 __le32 cmd_flags;
6838 __le32 noise_floor;
6839 __le32 rx_clear_count;
6840 __le32 cycle_count;
6841 __le32 chan_tx_pwr_range;
6842 __le32 chan_tx_pwr_tp;
6843 __le32 rx_frame_count;
6844 __le32 my_bss_rx_cycle_count;
6845 __le32 rx_11b_mode_data_duration;
6846 __le32 tx_frame_cnt;
6847 __le32 mac_clk_mhz;
6848 };
6850 /* From 10.4 firmware, not sure all have the same values. */
6853 WMI_VDEV_START_CHAN_INVALID,
6854 };
6857 __le32 vdev_id;
6858 __le32 req_id;
6861 };
6865 };
6868 __le32 vdev_map;
6871 };
6874 u32 tsf_timestamp;
6875 u16 freq1;
6876 u16 freq2;
6877 u8 rssi_combined;
6878 u8 chan_width_mhz;
6879 u8 phy_err_code;
6881 u32 buf_len;
6883 u8 hdr_len;
6884 };
6887 u32 num_phyerrs;
6888 u32 tsf_l32;
6889 u32 tsf_u32;
6890 u32 buf_len;
6892 };
6895 u32 status;
6896 };
6899 __le32 min_tx_power;
6900 __le32 max_tx_power;
6901 __le32 ht_cap;
6902 __le32 vht_cap;
6903 __le32 vht_supp_mcs;
6904 __le32 sw_ver0;
6905 __le32 sw_ver1;
6906 __le32 fw_build;
6907 __le32 phy_capab;
6908 __le32 num_rf_chains;
6909 __le32 eeprom_rd;
6910 __le32 num_mem_reqs;
6911 __le32 low_2ghz_chan;
6912 __le32 high_2ghz_chan;
6913 __le32 low_5ghz_chan;
6914 __le32 high_5ghz_chan;
6915 __le32 sys_cap_info;
6919 };
6923 __le32 service_map_ext_len;
6925 };
6928 __le32 sw_version;
6929 __le32 abi_version;
6930 __le32 status;
6932 };
6935 __le32 vdev_id;
6936 __le32 reason;
6937 __le32 rssi;
6938 };
6941 __le32 value;
6942 };
6945 /* temperature value in Celcius degree */
6946 __le32 temperature;
6950 __le32 freq;
6951 __le32 noise_floor;
6952 __le64 cycle_busy;
6953 __le64 cycle_total;
6954 __le64 cycle_tx;
6955 __le64 cycle_rx;
6956 __le64 cycle_rx_bss;
6957 __le32 reserved;
6960 /* WOW structures */
6963 WOW_BETTER_AP_EVENT,
6964 WOW_DEAUTH_RECVD_EVENT,
6965 WOW_MAGIC_PKT_RECVD_EVENT,
6966 WOW_GTK_ERR_EVENT,
6967 WOW_FOURWAY_HSHAKE_EVENT,
6968 WOW_EAPOL_RECVD_EVENT,
6969 WOW_NLO_DETECTED_EVENT,
6970 WOW_DISASSOC_RECVD_EVENT,
6971 WOW_PATTERN_MATCH_EVENT,
6972 WOW_CSA_IE_EVENT,
6973 WOW_PROBE_REQ_WPS_IE_EVENT,
6974 WOW_AUTH_REQ_EVENT,
6975 WOW_ASSOC_REQ_EVENT,
6976 WOW_HTT_EVENT,
6977 WOW_RA_MATCH_EVENT,
6978 WOW_HOST_AUTO_SHUTDOWN_EVENT,
6979 WOW_IOAC_MAGIC_EVENT,
6980 WOW_IOAC_SHORT_EVENT,
6981 WOW_IOAC_EXTEND_EVENT,
6982 WOW_IOAC_TIMER_EVENT,
6983 WOW_DFS_PHYERR_RADAR_EVENT,
6984 WOW_BEACON_EVENT,
6985 WOW_CLIENT_KICKOUT_EVENT,
6986 WOW_EVENT_MAX,
6987 };
6989 #define C2S(x) case x: return #x
6992 {
7021 }
7022 }
7027 WOW_REASON_AP_ASSOC_LOST,
7028 WOW_REASON_LOW_RSSI,
7029 WOW_REASON_DEAUTH_RECVD,
7030 WOW_REASON_DISASSOC_RECVD,
7031 WOW_REASON_GTK_HS_ERR,
7032 WOW_REASON_EAP_REQ,
7033 WOW_REASON_FOURWAY_HS_RECV,
7034 WOW_REASON_TIMER_INTR_RECV,
7035 WOW_REASON_PATTERN_MATCH_FOUND,
7036 WOW_REASON_RECV_MAGIC_PATTERN,
7037 WOW_REASON_P2P_DISC,
7038 WOW_REASON_WLAN_HB,
7039 WOW_REASON_CSA_EVENT,
7040 WOW_REASON_PROBE_REQ_WPS_IE_RECV,
7041 WOW_REASON_AUTH_REQ_RECV,
7042 WOW_REASON_ASSOC_REQ_RECV,
7043 WOW_REASON_HTT_EVENT,
7044 WOW_REASON_RA_MATCH,
7045 WOW_REASON_HOST_AUTO_SHUTDOWN,
7046 WOW_REASON_IOAC_MAGIC_EVENT,
7047 WOW_REASON_IOAC_SHORT_EVENT,
7048 WOW_REASON_IOAC_EXTEND_EVENT,
7049 WOW_REASON_IOAC_TIMER_EVENT,
7050 WOW_REASON_ROAM_HO,
7051 WOW_REASON_DFS_PHYERR_RADADR_EVENT,
7052 WOW_REASON_BEACON_RECV,
7053 WOW_REASON_CLIENT_KICKOUT_EVENT,
7055 };
7058 {
7092 }
7093 }
7095 #undef C2S
7098 u32 vdev_id;
7099 u32 flag;
7101 u32 data_len;
7102 };
7104 #define WOW_MIN_PATTERN_SIZE 1
7105 #define WOW_MAX_PATTERN_SIZE 148
7106 #define WOW_MAX_PKT_OFFSET 128
7107 #define WOW_HDR_LEN (sizeof(struct ieee80211_hdr_3addr) + \
7108 sizeof(struct rfc1042_hdr))
7109 #define WOW_MAX_REDUCE (WOW_HDR_LEN - sizeof(struct ethhdr) - \
7110 offsetof(struct ieee80211_hdr_3addr, addr1))
7113 WMI_TDLS_DISABLE,
7114 WMI_TDLS_ENABLE_PASSIVE,
7115 WMI_TDLS_ENABLE_ACTIVE,
7116 WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL,
7117 };
7120 WMI_TDLS_PEER_STATE_PEERING,
7121 WMI_TDLS_PEER_STATE_CONNECTED,
7122 WMI_TDLS_PEER_STATE_TEARDOWN,
7123 };
7126 u32 vdev_id;
7129 };
7131 #define WMI_TDLS_MAX_SUPP_OPER_CLASSES 32
7133 #define WMI_TDLS_PEER_SP_MASK 0x60
7134 #define WMI_TDLS_PEER_SP_LSB 5
7140 };
7147 };
7150 u8 peer_uapsd_queues;
7151 u8 peer_max_sp;
7152 u32 buff_sta_support;
7153 u32 off_chan_support;
7154 u32 peer_curr_operclass;
7155 u32 self_curr_operclass;
7156 u32 peer_chan_len;
7157 u32 peer_operclass_len;
7159 u32 is_peer_responder;
7160 u32 pref_offchan_num;
7161 u32 pref_offchan_bw;
7162 };
7165 __le32 vdev_id;
7166 __le32 state;
7167 __le32 notification_interval_ms;
7168 __le32 tx_discovery_threshold;
7169 __le32 tx_teardown_threshold;
7170 __le32 rssi_teardown_threshold;
7171 __le32 rssi_delta;
7172 __le32 tdls_options;
7173 __le32 tdls_peer_traffic_ind_window;
7174 __le32 tdls_peer_traffic_response_timeout_ms;
7175 __le32 tdls_puapsd_mask;
7176 __le32 tdls_puapsd_inactivity_time_ms;
7177 __le32 tdls_puapsd_rx_frame_threshold;
7178 __le32 teardown_notification_ms;
7179 __le32 tdls_peer_kickout_threshold;
7183 __le32 peer_qos;
7184 __le32 buff_sta_support;
7185 __le32 off_chan_support;
7186 __le32 peer_curr_operclass;
7187 __le32 self_curr_operclass;
7188 __le32 peer_chan_len;
7189 __le32 peer_operclass_len;
7191 __le32 is_peer_responder;
7192 __le32 pref_offchan_num;
7193 __le32 pref_offchan_bw;
7198 __le32 vdev_id;
7200 __le32 peer_state;
7206 WMI_TDLS_TEARDOWN_REASON_TX,
7207 WMI_TDLS_TEARDOWN_REASON_RSSI,
7208 WMI_TDLS_TEARDOWN_REASON_SCAN,
7209 WMI_TDLS_DISCONNECTED_REASON_PEER_DELETE,
7210 WMI_TDLS_TEARDOWN_REASON_PTR_TIMEOUT,
7211 WMI_TDLS_TEARDOWN_REASON_BAD_PTR,
7212 WMI_TDLS_TEARDOWN_REASON_NO_RESPONSE,
7213 WMI_TDLS_ENTER_BUF_STA,
7214 WMI_TDLS_EXIT_BUF_STA,
7215 WMI_TDLS_ENTER_BT_BUSY_MODE,
7216 WMI_TDLS_EXIT_BT_BUSY_MODE,
7217 WMI_TDLS_SCAN_STARTED_EVENT,
7218 WMI_TDLS_SCAN_COMPLETED_EVENT,
7219 };
7222 WMI_TDLS_SHOULD_DISCOVER,
7223 WMI_TDLS_SHOULD_TEARDOWN,
7224 WMI_TDLS_PEER_DISCONNECTED,
7225 WMI_TDLS_CONNECTION_TRACKER_NOTIFICATION,
7226 };
7230 /* see enum wmi_tdls_peer_notification*/
7231 __le32 peer_status;
7232 /* see enum wmi_tdls_peer_reason */
7233 __le32 peer_reason;
7234 __le32 vdev_id;
7238 WMI_TID_CONFIG_AGGR_CONTROL_IGNORE,
7239 WMI_TID_CONFIG_AGGR_CONTROL_ENABLE,
7240 WMI_TID_CONFIG_AGGR_CONTROL_DISABLE,
7241 };
7244 WMI_NOACK_TID_CONFIG_IGNORE_ACK_POLICY,
7245 WMI_PEER_TID_CONFIG_ACK,
7246 WMI_PEER_TID_CONFIG_NOACK,
7247 };
7250 WMI_TID_CONFIG_RATE_CONTROL_IGNORE,
7251 WMI_TID_CONFIG_RATE_CONTROL_AUTO,
7252 WMI_TID_CONFIG_RATE_CONTROL_FIXED_RATE,
7253 WMI_TID_CONFIG_RATE_CONTROL_DEFAULT_LOWEST_RATE,
7254 WMI_PEER_TID_CONFIG_RATE_UPPER_CAP,
7255 };
7258 WMI_TID_CONFIG_RTSCTS_CONTROL_ENABLE,
7259 WMI_TID_CONFIG_RTSCTS_CONTROL_DISABLE,
7260 };
7264 };
7267 u32 vdev_id;
7269 u32 tid;
7272 u8 rate_ctrl;
7273 u32 retry_count;
7274 u32 rcode_flags;
7275 u32 ext_tid_cfg_bitmap;
7276 u32 rtscts_ctrl;
7277 };
7280 __le32 vdev_id;
7282 __le32 tid;
7284 /* see enum wmi_noack_tid_conf */
7285 __le32 ack_policy;
7287 /* see enum wmi_tid_aggr_control_conf */
7288 __le32 aggr_control;
7290 /* see enum wmi_tid_rate_ctrl_conf */
7291 __le32 rate_control;
7292 __le32 rcode_flags;
7293 __le32 retry_count;
7295 /* See enum wmi_ext_tid_config_map */
7296 __le32 ext_tid_cfg_bitmap;
7298 /* see enum wmi_tid_rtscts_control_conf */
7299 __le32 rtscts_ctrl;
7303 WMI_TXBF_CONF_UNSUPPORTED,
7304 WMI_TXBF_CONF_BEFORE_ASSOC,
7305 WMI_TXBF_CONF_AFTER_ASSOC,
7306 };
7308 #define WMI_CCA_DETECT_LEVEL_AUTO 0
7309 #define WMI_CCA_DETECT_MARGIN_AUTO 0
7312 __le32 enable;
7313 __le32 cca_detect_level;
7314 __le32 cca_detect_margin;
7317 #define WMI_PNO_MAX_SCHED_SCAN_PLANS 2
7318 #define WMI_PNO_MAX_SCHED_SCAN_PLAN_INT 7200
7319 #define WMI_PNO_MAX_SCHED_SCAN_PLAN_ITRNS 100
7320 #define WMI_PNO_MAX_NETW_CHANNELS 26
7321 #define WMI_PNO_MAX_NETW_CHANNELS_EX 60
7322 #define WMI_PNO_MAX_SUPP_NETWORKS WLAN_SCAN_PARAMS_MAX_SSID
7323 #define WMI_PNO_MAX_IE_LENGTH WLAN_SCAN_PARAMS_MAX_IE_LEN
7325 /*size based of dot11 declaration without extra IEs as we will not carry those for PNO*/
7326 #define WMI_PNO_MAX_PB_REQ_SIZE 450
7328 #define WMI_PNO_24G_DEFAULT_CH 1
7329 #define WMI_PNO_5G_DEFAULT_CH 36
7331 #define WMI_ACTIVE_MAX_CHANNEL_TIME 40
7332 #define WMI_PASSIVE_MAX_CHANNEL_TIME 110
7334 /* SSID broadcast type */
7339 };
7343 u32 authentication;
7344 u32 encryption;
7345 u32 bcast_nw_type;
7346 u8 channel_count;
7348 s32 rssi_threshold;
7352 u8 enable;
7353 u8 vdev_id;
7354 u8 uc_networks_count;
7356 u32 fast_scan_period;
7357 u32 slow_scan_period;
7358 u8 fast_scan_max_cycles;
7362 u32 delay_start_time;
7363 u32 active_min_time;
7364 u32 active_max_time;
7365 u32 passive_min_time;
7366 u32 passive_max_time;
7368 /* mac address randomization attributes */
7369 u32 enable_pno_scan_randomization;
7375 WMI_HOST_PLATFORM_HIGH_PERF,
7376 WMI_HOST_PLATFORM_LOW_PERF,
7377 };
7381 WMI_BSS_SURVEY_REQ_TYPE_READ_CLEAR,
7382 };
7385 __le32 type;
7386 __le32 reserved;
7389 /* bb timing register configurations */
7391 /* Tx_end to pa off timing */
7392 u32 bb_tx_timing;
7394 /* Tx_end to external pa off timing */
7395 u32 bb_xpa_timing;
7396 };
7399 /* Tx_end to pa off timing */
7400 __le32 bb_tx_timing;
7402 /* Tx_end to external pa off timing */
7403 __le32 bb_xpa_timing;
7424 u32 cmd_id);
7464 u64 tsf);
7510 u32 num_tx_chain);