ASoC: arizona: Correct handling of FLL theta in synchroniser mode
[linux/fpc-iii.git] / drivers / mmc / host / omap_hsmmc.c
blob24ebc9a8de89a072201fba04276fd27e1b68d3e8
1 /*
2 * drivers/mmc/host/omap_hsmmc.c
4 * Driver for OMAP2430/3430 MMC controller.
6 * Copyright (C) 2007 Texas Instruments.
8 * Authors:
9 * Syed Mohammed Khasim <x0khasim@ti.com>
10 * Madhusudhan <madhu.cr@ti.com>
11 * Mohit Jalori <mjalori@ti.com>
13 * This file is licensed under the terms of the GNU General Public License
14 * version 2. This program is licensed "as is" without any warranty of any
15 * kind, whether express or implied.
18 #include <linux/module.h>
19 #include <linux/init.h>
20 #include <linux/kernel.h>
21 #include <linux/debugfs.h>
22 #include <linux/dmaengine.h>
23 #include <linux/seq_file.h>
24 #include <linux/sizes.h>
25 #include <linux/interrupt.h>
26 #include <linux/delay.h>
27 #include <linux/dma-mapping.h>
28 #include <linux/platform_device.h>
29 #include <linux/timer.h>
30 #include <linux/clk.h>
31 #include <linux/of.h>
32 #include <linux/of_irq.h>
33 #include <linux/of_gpio.h>
34 #include <linux/of_device.h>
35 #include <linux/mmc/host.h>
36 #include <linux/mmc/core.h>
37 #include <linux/mmc/mmc.h>
38 #include <linux/mmc/slot-gpio.h>
39 #include <linux/io.h>
40 #include <linux/irq.h>
41 #include <linux/gpio.h>
42 #include <linux/regulator/consumer.h>
43 #include <linux/pinctrl/consumer.h>
44 #include <linux/pm_runtime.h>
45 #include <linux/pm_wakeirq.h>
46 #include <linux/platform_data/hsmmc-omap.h>
48 /* OMAP HSMMC Host Controller Registers */
49 #define OMAP_HSMMC_SYSSTATUS 0x0014
50 #define OMAP_HSMMC_CON 0x002C
51 #define OMAP_HSMMC_SDMASA 0x0100
52 #define OMAP_HSMMC_BLK 0x0104
53 #define OMAP_HSMMC_ARG 0x0108
54 #define OMAP_HSMMC_CMD 0x010C
55 #define OMAP_HSMMC_RSP10 0x0110
56 #define OMAP_HSMMC_RSP32 0x0114
57 #define OMAP_HSMMC_RSP54 0x0118
58 #define OMAP_HSMMC_RSP76 0x011C
59 #define OMAP_HSMMC_DATA 0x0120
60 #define OMAP_HSMMC_PSTATE 0x0124
61 #define OMAP_HSMMC_HCTL 0x0128
62 #define OMAP_HSMMC_SYSCTL 0x012C
63 #define OMAP_HSMMC_STAT 0x0130
64 #define OMAP_HSMMC_IE 0x0134
65 #define OMAP_HSMMC_ISE 0x0138
66 #define OMAP_HSMMC_AC12 0x013C
67 #define OMAP_HSMMC_CAPA 0x0140
69 #define VS18 (1 << 26)
70 #define VS30 (1 << 25)
71 #define HSS (1 << 21)
72 #define SDVS18 (0x5 << 9)
73 #define SDVS30 (0x6 << 9)
74 #define SDVS33 (0x7 << 9)
75 #define SDVS_MASK 0x00000E00
76 #define SDVSCLR 0xFFFFF1FF
77 #define SDVSDET 0x00000400
78 #define AUTOIDLE 0x1
79 #define SDBP (1 << 8)
80 #define DTO 0xe
81 #define ICE 0x1
82 #define ICS 0x2
83 #define CEN (1 << 2)
84 #define CLKD_MAX 0x3FF /* max clock divisor: 1023 */
85 #define CLKD_MASK 0x0000FFC0
86 #define CLKD_SHIFT 6
87 #define DTO_MASK 0x000F0000
88 #define DTO_SHIFT 16
89 #define INIT_STREAM (1 << 1)
90 #define ACEN_ACMD23 (2 << 2)
91 #define DP_SELECT (1 << 21)
92 #define DDIR (1 << 4)
93 #define DMAE 0x1
94 #define MSBS (1 << 5)
95 #define BCE (1 << 1)
96 #define FOUR_BIT (1 << 1)
97 #define HSPE (1 << 2)
98 #define IWE (1 << 24)
99 #define DDR (1 << 19)
100 #define CLKEXTFREE (1 << 16)
101 #define CTPL (1 << 11)
102 #define DW8 (1 << 5)
103 #define OD 0x1
104 #define STAT_CLEAR 0xFFFFFFFF
105 #define INIT_STREAM_CMD 0x00000000
106 #define DUAL_VOLT_OCR_BIT 7
107 #define SRC (1 << 25)
108 #define SRD (1 << 26)
109 #define SOFTRESET (1 << 1)
111 /* PSTATE */
112 #define DLEV_DAT(x) (1 << (20 + (x)))
114 /* Interrupt masks for IE and ISE register */
115 #define CC_EN (1 << 0)
116 #define TC_EN (1 << 1)
117 #define BWR_EN (1 << 4)
118 #define BRR_EN (1 << 5)
119 #define CIRQ_EN (1 << 8)
120 #define ERR_EN (1 << 15)
121 #define CTO_EN (1 << 16)
122 #define CCRC_EN (1 << 17)
123 #define CEB_EN (1 << 18)
124 #define CIE_EN (1 << 19)
125 #define DTO_EN (1 << 20)
126 #define DCRC_EN (1 << 21)
127 #define DEB_EN (1 << 22)
128 #define ACE_EN (1 << 24)
129 #define CERR_EN (1 << 28)
130 #define BADA_EN (1 << 29)
132 #define INT_EN_MASK (BADA_EN | CERR_EN | ACE_EN | DEB_EN | DCRC_EN |\
133 DTO_EN | CIE_EN | CEB_EN | CCRC_EN | CTO_EN | \
134 BRR_EN | BWR_EN | TC_EN | CC_EN)
136 #define CNI (1 << 7)
137 #define ACIE (1 << 4)
138 #define ACEB (1 << 3)
139 #define ACCE (1 << 2)
140 #define ACTO (1 << 1)
141 #define ACNE (1 << 0)
143 #define MMC_AUTOSUSPEND_DELAY 100
144 #define MMC_TIMEOUT_MS 20 /* 20 mSec */
145 #define MMC_TIMEOUT_US 20000 /* 20000 micro Sec */
146 #define OMAP_MMC_MIN_CLOCK 400000
147 #define OMAP_MMC_MAX_CLOCK 52000000
148 #define DRIVER_NAME "omap_hsmmc"
150 #define VDD_1V8 1800000 /* 180000 uV */
151 #define VDD_3V0 3000000 /* 300000 uV */
152 #define VDD_165_195 (ffs(MMC_VDD_165_195) - 1)
155 * One controller can have multiple slots, like on some omap boards using
156 * omap.c controller driver. Luckily this is not currently done on any known
157 * omap_hsmmc.c device.
159 #define mmc_pdata(host) host->pdata
162 * MMC Host controller read/write API's
164 #define OMAP_HSMMC_READ(base, reg) \
165 __raw_readl((base) + OMAP_HSMMC_##reg)
167 #define OMAP_HSMMC_WRITE(base, reg, val) \
168 __raw_writel((val), (base) + OMAP_HSMMC_##reg)
170 struct omap_hsmmc_next {
171 unsigned int dma_len;
172 s32 cookie;
175 struct omap_hsmmc_host {
176 struct device *dev;
177 struct mmc_host *mmc;
178 struct mmc_request *mrq;
179 struct mmc_command *cmd;
180 struct mmc_data *data;
181 struct clk *fclk;
182 struct clk *dbclk;
183 struct regulator *pbias;
184 bool pbias_enabled;
185 void __iomem *base;
186 int vqmmc_enabled;
187 resource_size_t mapbase;
188 spinlock_t irq_lock; /* Prevent races with irq handler */
189 unsigned int dma_len;
190 unsigned int dma_sg_idx;
191 unsigned char bus_mode;
192 unsigned char power_mode;
193 int suspended;
194 u32 con;
195 u32 hctl;
196 u32 sysctl;
197 u32 capa;
198 int irq;
199 int wake_irq;
200 int use_dma, dma_ch;
201 struct dma_chan *tx_chan;
202 struct dma_chan *rx_chan;
203 int response_busy;
204 int context_loss;
205 int protect_card;
206 int reqs_blocked;
207 int req_in_progress;
208 unsigned long clk_rate;
209 unsigned int flags;
210 #define AUTO_CMD23 (1 << 0) /* Auto CMD23 support */
211 #define HSMMC_SDIO_IRQ_ENABLED (1 << 1) /* SDIO irq enabled */
212 struct omap_hsmmc_next next_data;
213 struct omap_hsmmc_platform_data *pdata;
215 /* return MMC cover switch state, can be NULL if not supported.
217 * possible return values:
218 * 0 - closed
219 * 1 - open
221 int (*get_cover_state)(struct device *dev);
223 int (*card_detect)(struct device *dev);
226 struct omap_mmc_of_data {
227 u32 reg_offset;
228 u8 controller_flags;
231 static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host);
233 static int omap_hsmmc_card_detect(struct device *dev)
235 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
237 return mmc_gpio_get_cd(host->mmc);
240 static int omap_hsmmc_get_cover_state(struct device *dev)
242 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
244 return mmc_gpio_get_cd(host->mmc);
247 static int omap_hsmmc_enable_supply(struct mmc_host *mmc)
249 int ret;
250 struct omap_hsmmc_host *host = mmc_priv(mmc);
251 struct mmc_ios *ios = &mmc->ios;
253 if (mmc->supply.vmmc) {
254 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
255 if (ret)
256 return ret;
259 /* Enable interface voltage rail, if needed */
260 if (mmc->supply.vqmmc && !host->vqmmc_enabled) {
261 ret = regulator_enable(mmc->supply.vqmmc);
262 if (ret) {
263 dev_err(mmc_dev(mmc), "vmmc_aux reg enable failed\n");
264 goto err_vqmmc;
266 host->vqmmc_enabled = 1;
269 return 0;
271 err_vqmmc:
272 if (mmc->supply.vmmc)
273 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
275 return ret;
278 static int omap_hsmmc_disable_supply(struct mmc_host *mmc)
280 int ret;
281 int status;
282 struct omap_hsmmc_host *host = mmc_priv(mmc);
284 if (mmc->supply.vqmmc && host->vqmmc_enabled) {
285 ret = regulator_disable(mmc->supply.vqmmc);
286 if (ret) {
287 dev_err(mmc_dev(mmc), "vmmc_aux reg disable failed\n");
288 return ret;
290 host->vqmmc_enabled = 0;
293 if (mmc->supply.vmmc) {
294 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
295 if (ret)
296 goto err_set_ocr;
299 return 0;
301 err_set_ocr:
302 if (mmc->supply.vqmmc) {
303 status = regulator_enable(mmc->supply.vqmmc);
304 if (status)
305 dev_err(mmc_dev(mmc), "vmmc_aux re-enable failed\n");
308 return ret;
311 static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on,
312 int vdd)
314 int ret;
316 if (!host->pbias)
317 return 0;
319 if (power_on) {
320 if (vdd <= VDD_165_195)
321 ret = regulator_set_voltage(host->pbias, VDD_1V8,
322 VDD_1V8);
323 else
324 ret = regulator_set_voltage(host->pbias, VDD_3V0,
325 VDD_3V0);
326 if (ret < 0) {
327 dev_err(host->dev, "pbias set voltage fail\n");
328 return ret;
331 if (host->pbias_enabled == 0) {
332 ret = regulator_enable(host->pbias);
333 if (ret) {
334 dev_err(host->dev, "pbias reg enable fail\n");
335 return ret;
337 host->pbias_enabled = 1;
339 } else {
340 if (host->pbias_enabled == 1) {
341 ret = regulator_disable(host->pbias);
342 if (ret) {
343 dev_err(host->dev, "pbias reg disable fail\n");
344 return ret;
346 host->pbias_enabled = 0;
350 return 0;
353 static int omap_hsmmc_set_power(struct omap_hsmmc_host *host, int power_on,
354 int vdd)
356 struct mmc_host *mmc = host->mmc;
357 int ret = 0;
359 if (mmc_pdata(host)->set_power)
360 return mmc_pdata(host)->set_power(host->dev, power_on, vdd);
363 * If we don't see a Vcc regulator, assume it's a fixed
364 * voltage always-on regulator.
366 if (!mmc->supply.vmmc)
367 return 0;
369 if (mmc_pdata(host)->before_set_reg)
370 mmc_pdata(host)->before_set_reg(host->dev, power_on, vdd);
372 ret = omap_hsmmc_set_pbias(host, false, 0);
373 if (ret)
374 return ret;
377 * Assume Vcc regulator is used only to power the card ... OMAP
378 * VDDS is used to power the pins, optionally with a transceiver to
379 * support cards using voltages other than VDDS (1.8V nominal). When a
380 * transceiver is used, DAT3..7 are muxed as transceiver control pins.
382 * In some cases this regulator won't support enable/disable;
383 * e.g. it's a fixed rail for a WLAN chip.
385 * In other cases vcc_aux switches interface power. Example, for
386 * eMMC cards it represents VccQ. Sometimes transceivers or SDIO
387 * chips/cards need an interface voltage rail too.
389 if (power_on) {
390 ret = omap_hsmmc_enable_supply(mmc);
391 if (ret)
392 return ret;
394 ret = omap_hsmmc_set_pbias(host, true, vdd);
395 if (ret)
396 goto err_set_voltage;
397 } else {
398 ret = omap_hsmmc_disable_supply(mmc);
399 if (ret)
400 return ret;
403 if (mmc_pdata(host)->after_set_reg)
404 mmc_pdata(host)->after_set_reg(host->dev, power_on, vdd);
406 return 0;
408 err_set_voltage:
409 omap_hsmmc_disable_supply(mmc);
411 return ret;
414 static int omap_hsmmc_disable_boot_regulator(struct regulator *reg)
416 int ret;
418 if (!reg)
419 return 0;
421 if (regulator_is_enabled(reg)) {
422 ret = regulator_enable(reg);
423 if (ret)
424 return ret;
426 ret = regulator_disable(reg);
427 if (ret)
428 return ret;
431 return 0;
434 static int omap_hsmmc_disable_boot_regulators(struct omap_hsmmc_host *host)
436 struct mmc_host *mmc = host->mmc;
437 int ret;
440 * disable regulators enabled during boot and get the usecount
441 * right so that regulators can be enabled/disabled by checking
442 * the return value of regulator_is_enabled
444 ret = omap_hsmmc_disable_boot_regulator(mmc->supply.vmmc);
445 if (ret) {
446 dev_err(host->dev, "fail to disable boot enabled vmmc reg\n");
447 return ret;
450 ret = omap_hsmmc_disable_boot_regulator(mmc->supply.vqmmc);
451 if (ret) {
452 dev_err(host->dev,
453 "fail to disable boot enabled vmmc_aux reg\n");
454 return ret;
457 ret = omap_hsmmc_disable_boot_regulator(host->pbias);
458 if (ret) {
459 dev_err(host->dev,
460 "failed to disable boot enabled pbias reg\n");
461 return ret;
464 return 0;
467 static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host)
469 int ocr_value = 0;
470 int ret;
471 struct mmc_host *mmc = host->mmc;
473 if (mmc_pdata(host)->set_power)
474 return 0;
476 mmc->supply.vmmc = devm_regulator_get_optional(host->dev, "vmmc");
477 if (IS_ERR(mmc->supply.vmmc)) {
478 ret = PTR_ERR(mmc->supply.vmmc);
479 if ((ret != -ENODEV) && host->dev->of_node)
480 return ret;
481 dev_dbg(host->dev, "unable to get vmmc regulator %ld\n",
482 PTR_ERR(mmc->supply.vmmc));
483 mmc->supply.vmmc = NULL;
484 } else {
485 ocr_value = mmc_regulator_get_ocrmask(mmc->supply.vmmc);
486 if (ocr_value > 0)
487 mmc_pdata(host)->ocr_mask = ocr_value;
490 /* Allow an aux regulator */
491 mmc->supply.vqmmc = devm_regulator_get_optional(host->dev, "vmmc_aux");
492 if (IS_ERR(mmc->supply.vqmmc)) {
493 ret = PTR_ERR(mmc->supply.vqmmc);
494 if ((ret != -ENODEV) && host->dev->of_node)
495 return ret;
496 dev_dbg(host->dev, "unable to get vmmc_aux regulator %ld\n",
497 PTR_ERR(mmc->supply.vqmmc));
498 mmc->supply.vqmmc = NULL;
501 host->pbias = devm_regulator_get_optional(host->dev, "pbias");
502 if (IS_ERR(host->pbias)) {
503 ret = PTR_ERR(host->pbias);
504 if ((ret != -ENODEV) && host->dev->of_node) {
505 dev_err(host->dev,
506 "SD card detect fail? enable CONFIG_REGULATOR_PBIAS\n");
507 return ret;
509 dev_dbg(host->dev, "unable to get pbias regulator %ld\n",
510 PTR_ERR(host->pbias));
511 host->pbias = NULL;
514 /* For eMMC do not power off when not in sleep state */
515 if (mmc_pdata(host)->no_regulator_off_init)
516 return 0;
518 ret = omap_hsmmc_disable_boot_regulators(host);
519 if (ret)
520 return ret;
522 return 0;
525 static irqreturn_t omap_hsmmc_cover_irq(int irq, void *dev_id);
527 static int omap_hsmmc_gpio_init(struct mmc_host *mmc,
528 struct omap_hsmmc_host *host,
529 struct omap_hsmmc_platform_data *pdata)
531 int ret;
533 if (gpio_is_valid(pdata->gpio_cod)) {
534 ret = mmc_gpio_request_cd(mmc, pdata->gpio_cod, 0);
535 if (ret)
536 return ret;
538 host->get_cover_state = omap_hsmmc_get_cover_state;
539 mmc_gpio_set_cd_isr(mmc, omap_hsmmc_cover_irq);
540 } else if (gpio_is_valid(pdata->gpio_cd)) {
541 ret = mmc_gpio_request_cd(mmc, pdata->gpio_cd, 0);
542 if (ret)
543 return ret;
545 host->card_detect = omap_hsmmc_card_detect;
548 if (gpio_is_valid(pdata->gpio_wp)) {
549 ret = mmc_gpio_request_ro(mmc, pdata->gpio_wp);
550 if (ret)
551 return ret;
554 return 0;
558 * Start clock to the card
560 static void omap_hsmmc_start_clock(struct omap_hsmmc_host *host)
562 OMAP_HSMMC_WRITE(host->base, SYSCTL,
563 OMAP_HSMMC_READ(host->base, SYSCTL) | CEN);
567 * Stop clock to the card
569 static void omap_hsmmc_stop_clock(struct omap_hsmmc_host *host)
571 OMAP_HSMMC_WRITE(host->base, SYSCTL,
572 OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN);
573 if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0)
574 dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stopped\n");
577 static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host,
578 struct mmc_command *cmd)
580 u32 irq_mask = INT_EN_MASK;
581 unsigned long flags;
583 if (host->use_dma)
584 irq_mask &= ~(BRR_EN | BWR_EN);
586 /* Disable timeout for erases */
587 if (cmd->opcode == MMC_ERASE)
588 irq_mask &= ~DTO_EN;
590 spin_lock_irqsave(&host->irq_lock, flags);
591 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
592 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
594 /* latch pending CIRQ, but don't signal MMC core */
595 if (host->flags & HSMMC_SDIO_IRQ_ENABLED)
596 irq_mask |= CIRQ_EN;
597 OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
598 spin_unlock_irqrestore(&host->irq_lock, flags);
601 static void omap_hsmmc_disable_irq(struct omap_hsmmc_host *host)
603 u32 irq_mask = 0;
604 unsigned long flags;
606 spin_lock_irqsave(&host->irq_lock, flags);
607 /* no transfer running but need to keep cirq if enabled */
608 if (host->flags & HSMMC_SDIO_IRQ_ENABLED)
609 irq_mask |= CIRQ_EN;
610 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
611 OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
612 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
613 spin_unlock_irqrestore(&host->irq_lock, flags);
616 /* Calculate divisor for the given clock frequency */
617 static u16 calc_divisor(struct omap_hsmmc_host *host, struct mmc_ios *ios)
619 u16 dsor = 0;
621 if (ios->clock) {
622 dsor = DIV_ROUND_UP(clk_get_rate(host->fclk), ios->clock);
623 if (dsor > CLKD_MAX)
624 dsor = CLKD_MAX;
627 return dsor;
630 static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host)
632 struct mmc_ios *ios = &host->mmc->ios;
633 unsigned long regval;
634 unsigned long timeout;
635 unsigned long clkdiv;
637 dev_vdbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock);
639 omap_hsmmc_stop_clock(host);
641 regval = OMAP_HSMMC_READ(host->base, SYSCTL);
642 regval = regval & ~(CLKD_MASK | DTO_MASK);
643 clkdiv = calc_divisor(host, ios);
644 regval = regval | (clkdiv << 6) | (DTO << 16);
645 OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
646 OMAP_HSMMC_WRITE(host->base, SYSCTL,
647 OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
649 /* Wait till the ICS bit is set */
650 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
651 while ((OMAP_HSMMC_READ(host->base, SYSCTL) & ICS) != ICS
652 && time_before(jiffies, timeout))
653 cpu_relax();
656 * Enable High-Speed Support
657 * Pre-Requisites
658 * - Controller should support High-Speed-Enable Bit
659 * - Controller should not be using DDR Mode
660 * - Controller should advertise that it supports High Speed
661 * in capabilities register
662 * - MMC/SD clock coming out of controller > 25MHz
664 if ((mmc_pdata(host)->features & HSMMC_HAS_HSPE_SUPPORT) &&
665 (ios->timing != MMC_TIMING_MMC_DDR52) &&
666 (ios->timing != MMC_TIMING_UHS_DDR50) &&
667 ((OMAP_HSMMC_READ(host->base, CAPA) & HSS) == HSS)) {
668 regval = OMAP_HSMMC_READ(host->base, HCTL);
669 if (clkdiv && (clk_get_rate(host->fclk)/clkdiv) > 25000000)
670 regval |= HSPE;
671 else
672 regval &= ~HSPE;
674 OMAP_HSMMC_WRITE(host->base, HCTL, regval);
677 omap_hsmmc_start_clock(host);
680 static void omap_hsmmc_set_bus_width(struct omap_hsmmc_host *host)
682 struct mmc_ios *ios = &host->mmc->ios;
683 u32 con;
685 con = OMAP_HSMMC_READ(host->base, CON);
686 if (ios->timing == MMC_TIMING_MMC_DDR52 ||
687 ios->timing == MMC_TIMING_UHS_DDR50)
688 con |= DDR; /* configure in DDR mode */
689 else
690 con &= ~DDR;
691 switch (ios->bus_width) {
692 case MMC_BUS_WIDTH_8:
693 OMAP_HSMMC_WRITE(host->base, CON, con | DW8);
694 break;
695 case MMC_BUS_WIDTH_4:
696 OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
697 OMAP_HSMMC_WRITE(host->base, HCTL,
698 OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
699 break;
700 case MMC_BUS_WIDTH_1:
701 OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
702 OMAP_HSMMC_WRITE(host->base, HCTL,
703 OMAP_HSMMC_READ(host->base, HCTL) & ~FOUR_BIT);
704 break;
708 static void omap_hsmmc_set_bus_mode(struct omap_hsmmc_host *host)
710 struct mmc_ios *ios = &host->mmc->ios;
711 u32 con;
713 con = OMAP_HSMMC_READ(host->base, CON);
714 if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
715 OMAP_HSMMC_WRITE(host->base, CON, con | OD);
716 else
717 OMAP_HSMMC_WRITE(host->base, CON, con & ~OD);
720 #ifdef CONFIG_PM
723 * Restore the MMC host context, if it was lost as result of a
724 * power state change.
726 static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
728 struct mmc_ios *ios = &host->mmc->ios;
729 u32 hctl, capa;
730 unsigned long timeout;
732 if (host->con == OMAP_HSMMC_READ(host->base, CON) &&
733 host->hctl == OMAP_HSMMC_READ(host->base, HCTL) &&
734 host->sysctl == OMAP_HSMMC_READ(host->base, SYSCTL) &&
735 host->capa == OMAP_HSMMC_READ(host->base, CAPA))
736 return 0;
738 host->context_loss++;
740 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
741 if (host->power_mode != MMC_POWER_OFF &&
742 (1 << ios->vdd) <= MMC_VDD_23_24)
743 hctl = SDVS18;
744 else
745 hctl = SDVS30;
746 capa = VS30 | VS18;
747 } else {
748 hctl = SDVS18;
749 capa = VS18;
752 if (host->mmc->caps & MMC_CAP_SDIO_IRQ)
753 hctl |= IWE;
755 OMAP_HSMMC_WRITE(host->base, HCTL,
756 OMAP_HSMMC_READ(host->base, HCTL) | hctl);
758 OMAP_HSMMC_WRITE(host->base, CAPA,
759 OMAP_HSMMC_READ(host->base, CAPA) | capa);
761 OMAP_HSMMC_WRITE(host->base, HCTL,
762 OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
764 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
765 while ((OMAP_HSMMC_READ(host->base, HCTL) & SDBP) != SDBP
766 && time_before(jiffies, timeout))
769 OMAP_HSMMC_WRITE(host->base, ISE, 0);
770 OMAP_HSMMC_WRITE(host->base, IE, 0);
771 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
773 /* Do not initialize card-specific things if the power is off */
774 if (host->power_mode == MMC_POWER_OFF)
775 goto out;
777 omap_hsmmc_set_bus_width(host);
779 omap_hsmmc_set_clock(host);
781 omap_hsmmc_set_bus_mode(host);
783 out:
784 dev_dbg(mmc_dev(host->mmc), "context is restored: restore count %d\n",
785 host->context_loss);
786 return 0;
790 * Save the MMC host context (store the number of power state changes so far).
792 static void omap_hsmmc_context_save(struct omap_hsmmc_host *host)
794 host->con = OMAP_HSMMC_READ(host->base, CON);
795 host->hctl = OMAP_HSMMC_READ(host->base, HCTL);
796 host->sysctl = OMAP_HSMMC_READ(host->base, SYSCTL);
797 host->capa = OMAP_HSMMC_READ(host->base, CAPA);
800 #else
802 static int omap_hsmmc_context_restore(struct omap_hsmmc_host *host)
804 return 0;
807 static void omap_hsmmc_context_save(struct omap_hsmmc_host *host)
811 #endif
814 * Send init stream sequence to card
815 * before sending IDLE command
817 static void send_init_stream(struct omap_hsmmc_host *host)
819 int reg = 0;
820 unsigned long timeout;
822 if (host->protect_card)
823 return;
825 disable_irq(host->irq);
827 OMAP_HSMMC_WRITE(host->base, IE, INT_EN_MASK);
828 OMAP_HSMMC_WRITE(host->base, CON,
829 OMAP_HSMMC_READ(host->base, CON) | INIT_STREAM);
830 OMAP_HSMMC_WRITE(host->base, CMD, INIT_STREAM_CMD);
832 timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS);
833 while ((reg != CC_EN) && time_before(jiffies, timeout))
834 reg = OMAP_HSMMC_READ(host->base, STAT) & CC_EN;
836 OMAP_HSMMC_WRITE(host->base, CON,
837 OMAP_HSMMC_READ(host->base, CON) & ~INIT_STREAM);
839 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
840 OMAP_HSMMC_READ(host->base, STAT);
842 enable_irq(host->irq);
845 static inline
846 int omap_hsmmc_cover_is_closed(struct omap_hsmmc_host *host)
848 int r = 1;
850 if (host->get_cover_state)
851 r = host->get_cover_state(host->dev);
852 return r;
855 static ssize_t
856 omap_hsmmc_show_cover_switch(struct device *dev, struct device_attribute *attr,
857 char *buf)
859 struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
860 struct omap_hsmmc_host *host = mmc_priv(mmc);
862 return sprintf(buf, "%s\n",
863 omap_hsmmc_cover_is_closed(host) ? "closed" : "open");
866 static DEVICE_ATTR(cover_switch, S_IRUGO, omap_hsmmc_show_cover_switch, NULL);
868 static ssize_t
869 omap_hsmmc_show_slot_name(struct device *dev, struct device_attribute *attr,
870 char *buf)
872 struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
873 struct omap_hsmmc_host *host = mmc_priv(mmc);
875 return sprintf(buf, "%s\n", mmc_pdata(host)->name);
878 static DEVICE_ATTR(slot_name, S_IRUGO, omap_hsmmc_show_slot_name, NULL);
881 * Configure the response type and send the cmd.
883 static void
884 omap_hsmmc_start_command(struct omap_hsmmc_host *host, struct mmc_command *cmd,
885 struct mmc_data *data)
887 int cmdreg = 0, resptype = 0, cmdtype = 0;
889 dev_vdbg(mmc_dev(host->mmc), "%s: CMD%d, argument 0x%08x\n",
890 mmc_hostname(host->mmc), cmd->opcode, cmd->arg);
891 host->cmd = cmd;
893 omap_hsmmc_enable_irq(host, cmd);
895 host->response_busy = 0;
896 if (cmd->flags & MMC_RSP_PRESENT) {
897 if (cmd->flags & MMC_RSP_136)
898 resptype = 1;
899 else if (cmd->flags & MMC_RSP_BUSY) {
900 resptype = 3;
901 host->response_busy = 1;
902 } else
903 resptype = 2;
907 * Unlike OMAP1 controller, the cmdtype does not seem to be based on
908 * ac, bc, adtc, bcr. Only commands ending an open ended transfer need
909 * a val of 0x3, rest 0x0.
911 if (cmd == host->mrq->stop)
912 cmdtype = 0x3;
914 cmdreg = (cmd->opcode << 24) | (resptype << 16) | (cmdtype << 22);
916 if ((host->flags & AUTO_CMD23) && mmc_op_multi(cmd->opcode) &&
917 host->mrq->sbc) {
918 cmdreg |= ACEN_ACMD23;
919 OMAP_HSMMC_WRITE(host->base, SDMASA, host->mrq->sbc->arg);
921 if (data) {
922 cmdreg |= DP_SELECT | MSBS | BCE;
923 if (data->flags & MMC_DATA_READ)
924 cmdreg |= DDIR;
925 else
926 cmdreg &= ~(DDIR);
929 if (host->use_dma)
930 cmdreg |= DMAE;
932 host->req_in_progress = 1;
934 OMAP_HSMMC_WRITE(host->base, ARG, cmd->arg);
935 OMAP_HSMMC_WRITE(host->base, CMD, cmdreg);
938 static int
939 omap_hsmmc_get_dma_dir(struct omap_hsmmc_host *host, struct mmc_data *data)
941 if (data->flags & MMC_DATA_WRITE)
942 return DMA_TO_DEVICE;
943 else
944 return DMA_FROM_DEVICE;
947 static struct dma_chan *omap_hsmmc_get_dma_chan(struct omap_hsmmc_host *host,
948 struct mmc_data *data)
950 return data->flags & MMC_DATA_WRITE ? host->tx_chan : host->rx_chan;
953 static void omap_hsmmc_request_done(struct omap_hsmmc_host *host, struct mmc_request *mrq)
955 int dma_ch;
956 unsigned long flags;
958 spin_lock_irqsave(&host->irq_lock, flags);
959 host->req_in_progress = 0;
960 dma_ch = host->dma_ch;
961 spin_unlock_irqrestore(&host->irq_lock, flags);
963 omap_hsmmc_disable_irq(host);
964 /* Do not complete the request if DMA is still in progress */
965 if (mrq->data && host->use_dma && dma_ch != -1)
966 return;
967 host->mrq = NULL;
968 mmc_request_done(host->mmc, mrq);
972 * Notify the transfer complete to MMC core
974 static void
975 omap_hsmmc_xfer_done(struct omap_hsmmc_host *host, struct mmc_data *data)
977 if (!data) {
978 struct mmc_request *mrq = host->mrq;
980 /* TC before CC from CMD6 - don't know why, but it happens */
981 if (host->cmd && host->cmd->opcode == 6 &&
982 host->response_busy) {
983 host->response_busy = 0;
984 return;
987 omap_hsmmc_request_done(host, mrq);
988 return;
991 host->data = NULL;
993 if (!data->error)
994 data->bytes_xfered += data->blocks * (data->blksz);
995 else
996 data->bytes_xfered = 0;
998 if (data->stop && (data->error || !host->mrq->sbc))
999 omap_hsmmc_start_command(host, data->stop, NULL);
1000 else
1001 omap_hsmmc_request_done(host, data->mrq);
1005 * Notify the core about command completion
1007 static void
1008 omap_hsmmc_cmd_done(struct omap_hsmmc_host *host, struct mmc_command *cmd)
1010 if (host->mrq->sbc && (host->cmd == host->mrq->sbc) &&
1011 !host->mrq->sbc->error && !(host->flags & AUTO_CMD23)) {
1012 host->cmd = NULL;
1013 omap_hsmmc_start_dma_transfer(host);
1014 omap_hsmmc_start_command(host, host->mrq->cmd,
1015 host->mrq->data);
1016 return;
1019 host->cmd = NULL;
1021 if (cmd->flags & MMC_RSP_PRESENT) {
1022 if (cmd->flags & MMC_RSP_136) {
1023 /* response type 2 */
1024 cmd->resp[3] = OMAP_HSMMC_READ(host->base, RSP10);
1025 cmd->resp[2] = OMAP_HSMMC_READ(host->base, RSP32);
1026 cmd->resp[1] = OMAP_HSMMC_READ(host->base, RSP54);
1027 cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP76);
1028 } else {
1029 /* response types 1, 1b, 3, 4, 5, 6 */
1030 cmd->resp[0] = OMAP_HSMMC_READ(host->base, RSP10);
1033 if ((host->data == NULL && !host->response_busy) || cmd->error)
1034 omap_hsmmc_request_done(host, host->mrq);
1038 * DMA clean up for command errors
1040 static void omap_hsmmc_dma_cleanup(struct omap_hsmmc_host *host, int errno)
1042 int dma_ch;
1043 unsigned long flags;
1045 host->data->error = errno;
1047 spin_lock_irqsave(&host->irq_lock, flags);
1048 dma_ch = host->dma_ch;
1049 host->dma_ch = -1;
1050 spin_unlock_irqrestore(&host->irq_lock, flags);
1052 if (host->use_dma && dma_ch != -1) {
1053 struct dma_chan *chan = omap_hsmmc_get_dma_chan(host, host->data);
1055 dmaengine_terminate_all(chan);
1056 dma_unmap_sg(chan->device->dev,
1057 host->data->sg, host->data->sg_len,
1058 omap_hsmmc_get_dma_dir(host, host->data));
1060 host->data->host_cookie = 0;
1062 host->data = NULL;
1066 * Readable error output
1068 #ifdef CONFIG_MMC_DEBUG
1069 static void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host, u32 status)
1071 /* --- means reserved bit without definition at documentation */
1072 static const char *omap_hsmmc_status_bits[] = {
1073 "CC" , "TC" , "BGE", "---", "BWR" , "BRR" , "---" , "---" ,
1074 "CIRQ", "OBI" , "---", "---", "---" , "---" , "---" , "ERRI",
1075 "CTO" , "CCRC", "CEB", "CIE", "DTO" , "DCRC", "DEB" , "---" ,
1076 "ACE" , "---" , "---", "---", "CERR", "BADA", "---" , "---"
1078 char res[256];
1079 char *buf = res;
1080 int len, i;
1082 len = sprintf(buf, "MMC IRQ 0x%x :", status);
1083 buf += len;
1085 for (i = 0; i < ARRAY_SIZE(omap_hsmmc_status_bits); i++)
1086 if (status & (1 << i)) {
1087 len = sprintf(buf, " %s", omap_hsmmc_status_bits[i]);
1088 buf += len;
1091 dev_vdbg(mmc_dev(host->mmc), "%s\n", res);
1093 #else
1094 static inline void omap_hsmmc_dbg_report_irq(struct omap_hsmmc_host *host,
1095 u32 status)
1098 #endif /* CONFIG_MMC_DEBUG */
1101 * MMC controller internal state machines reset
1103 * Used to reset command or data internal state machines, using respectively
1104 * SRC or SRD bit of SYSCTL register
1105 * Can be called from interrupt context
1107 static inline void omap_hsmmc_reset_controller_fsm(struct omap_hsmmc_host *host,
1108 unsigned long bit)
1110 unsigned long i = 0;
1111 unsigned long limit = MMC_TIMEOUT_US;
1113 OMAP_HSMMC_WRITE(host->base, SYSCTL,
1114 OMAP_HSMMC_READ(host->base, SYSCTL) | bit);
1117 * OMAP4 ES2 and greater has an updated reset logic.
1118 * Monitor a 0->1 transition first
1120 if (mmc_pdata(host)->features & HSMMC_HAS_UPDATED_RESET) {
1121 while ((!(OMAP_HSMMC_READ(host->base, SYSCTL) & bit))
1122 && (i++ < limit))
1123 udelay(1);
1125 i = 0;
1127 while ((OMAP_HSMMC_READ(host->base, SYSCTL) & bit) &&
1128 (i++ < limit))
1129 udelay(1);
1131 if (OMAP_HSMMC_READ(host->base, SYSCTL) & bit)
1132 dev_err(mmc_dev(host->mmc),
1133 "Timeout waiting on controller reset in %s\n",
1134 __func__);
1137 static void hsmmc_command_incomplete(struct omap_hsmmc_host *host,
1138 int err, int end_cmd)
1140 if (end_cmd) {
1141 omap_hsmmc_reset_controller_fsm(host, SRC);
1142 if (host->cmd)
1143 host->cmd->error = err;
1146 if (host->data) {
1147 omap_hsmmc_reset_controller_fsm(host, SRD);
1148 omap_hsmmc_dma_cleanup(host, err);
1149 } else if (host->mrq && host->mrq->cmd)
1150 host->mrq->cmd->error = err;
1153 static void omap_hsmmc_do_irq(struct omap_hsmmc_host *host, int status)
1155 struct mmc_data *data;
1156 int end_cmd = 0, end_trans = 0;
1157 int error = 0;
1159 data = host->data;
1160 dev_vdbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
1162 if (status & ERR_EN) {
1163 omap_hsmmc_dbg_report_irq(host, status);
1165 if (status & (CTO_EN | CCRC_EN))
1166 end_cmd = 1;
1167 if (host->data || host->response_busy) {
1168 end_trans = !end_cmd;
1169 host->response_busy = 0;
1171 if (status & (CTO_EN | DTO_EN))
1172 hsmmc_command_incomplete(host, -ETIMEDOUT, end_cmd);
1173 else if (status & (CCRC_EN | DCRC_EN | DEB_EN | CEB_EN |
1174 BADA_EN))
1175 hsmmc_command_incomplete(host, -EILSEQ, end_cmd);
1177 if (status & ACE_EN) {
1178 u32 ac12;
1179 ac12 = OMAP_HSMMC_READ(host->base, AC12);
1180 if (!(ac12 & ACNE) && host->mrq->sbc) {
1181 end_cmd = 1;
1182 if (ac12 & ACTO)
1183 error = -ETIMEDOUT;
1184 else if (ac12 & (ACCE | ACEB | ACIE))
1185 error = -EILSEQ;
1186 host->mrq->sbc->error = error;
1187 hsmmc_command_incomplete(host, error, end_cmd);
1189 dev_dbg(mmc_dev(host->mmc), "AC12 err: 0x%x\n", ac12);
1193 OMAP_HSMMC_WRITE(host->base, STAT, status);
1194 if (end_cmd || ((status & CC_EN) && host->cmd))
1195 omap_hsmmc_cmd_done(host, host->cmd);
1196 if ((end_trans || (status & TC_EN)) && host->mrq)
1197 omap_hsmmc_xfer_done(host, data);
1201 * MMC controller IRQ handler
1203 static irqreturn_t omap_hsmmc_irq(int irq, void *dev_id)
1205 struct omap_hsmmc_host *host = dev_id;
1206 int status;
1208 status = OMAP_HSMMC_READ(host->base, STAT);
1209 while (status & (INT_EN_MASK | CIRQ_EN)) {
1210 if (host->req_in_progress)
1211 omap_hsmmc_do_irq(host, status);
1213 if (status & CIRQ_EN)
1214 mmc_signal_sdio_irq(host->mmc);
1216 /* Flush posted write */
1217 status = OMAP_HSMMC_READ(host->base, STAT);
1220 return IRQ_HANDLED;
1223 static void set_sd_bus_power(struct omap_hsmmc_host *host)
1225 unsigned long i;
1227 OMAP_HSMMC_WRITE(host->base, HCTL,
1228 OMAP_HSMMC_READ(host->base, HCTL) | SDBP);
1229 for (i = 0; i < loops_per_jiffy; i++) {
1230 if (OMAP_HSMMC_READ(host->base, HCTL) & SDBP)
1231 break;
1232 cpu_relax();
1237 * Switch MMC interface voltage ... only relevant for MMC1.
1239 * MMC2 and MMC3 use fixed 1.8V levels, and maybe a transceiver.
1240 * The MMC2 transceiver controls are used instead of DAT4..DAT7.
1241 * Some chips, like eMMC ones, use internal transceivers.
1243 static int omap_hsmmc_switch_opcond(struct omap_hsmmc_host *host, int vdd)
1245 u32 reg_val = 0;
1246 int ret;
1248 /* Disable the clocks */
1249 if (host->dbclk)
1250 clk_disable_unprepare(host->dbclk);
1252 /* Turn the power off */
1253 ret = omap_hsmmc_set_power(host, 0, 0);
1255 /* Turn the power ON with given VDD 1.8 or 3.0v */
1256 if (!ret)
1257 ret = omap_hsmmc_set_power(host, 1, vdd);
1258 if (host->dbclk)
1259 clk_prepare_enable(host->dbclk);
1261 if (ret != 0)
1262 goto err;
1264 OMAP_HSMMC_WRITE(host->base, HCTL,
1265 OMAP_HSMMC_READ(host->base, HCTL) & SDVSCLR);
1266 reg_val = OMAP_HSMMC_READ(host->base, HCTL);
1269 * If a MMC dual voltage card is detected, the set_ios fn calls
1270 * this fn with VDD bit set for 1.8V. Upon card removal from the
1271 * slot, omap_hsmmc_set_ios sets the VDD back to 3V on MMC_POWER_OFF.
1273 * Cope with a bit of slop in the range ... per data sheets:
1274 * - "1.8V" for vdds_mmc1/vdds_mmc1a can be up to 2.45V max,
1275 * but recommended values are 1.71V to 1.89V
1276 * - "3.0V" for vdds_mmc1/vdds_mmc1a can be up to 3.5V max,
1277 * but recommended values are 2.7V to 3.3V
1279 * Board setup code shouldn't permit anything very out-of-range.
1280 * TWL4030-family VMMC1 and VSIM regulators are fine (avoiding the
1281 * middle range) but VSIM can't power DAT4..DAT7 at more than 3V.
1283 if ((1 << vdd) <= MMC_VDD_23_24)
1284 reg_val |= SDVS18;
1285 else
1286 reg_val |= SDVS30;
1288 OMAP_HSMMC_WRITE(host->base, HCTL, reg_val);
1289 set_sd_bus_power(host);
1291 return 0;
1292 err:
1293 dev_err(mmc_dev(host->mmc), "Unable to switch operating voltage\n");
1294 return ret;
1297 /* Protect the card while the cover is open */
1298 static void omap_hsmmc_protect_card(struct omap_hsmmc_host *host)
1300 if (!host->get_cover_state)
1301 return;
1303 host->reqs_blocked = 0;
1304 if (host->get_cover_state(host->dev)) {
1305 if (host->protect_card) {
1306 dev_info(host->dev, "%s: cover is closed, "
1307 "card is now accessible\n",
1308 mmc_hostname(host->mmc));
1309 host->protect_card = 0;
1311 } else {
1312 if (!host->protect_card) {
1313 dev_info(host->dev, "%s: cover is open, "
1314 "card is now inaccessible\n",
1315 mmc_hostname(host->mmc));
1316 host->protect_card = 1;
1322 * irq handler when (cell-phone) cover is mounted/removed
1324 static irqreturn_t omap_hsmmc_cover_irq(int irq, void *dev_id)
1326 struct omap_hsmmc_host *host = dev_id;
1328 sysfs_notify(&host->mmc->class_dev.kobj, NULL, "cover_switch");
1330 omap_hsmmc_protect_card(host);
1331 mmc_detect_change(host->mmc, (HZ * 200) / 1000);
1332 return IRQ_HANDLED;
1335 static void omap_hsmmc_dma_callback(void *param)
1337 struct omap_hsmmc_host *host = param;
1338 struct dma_chan *chan;
1339 struct mmc_data *data;
1340 int req_in_progress;
1342 spin_lock_irq(&host->irq_lock);
1343 if (host->dma_ch < 0) {
1344 spin_unlock_irq(&host->irq_lock);
1345 return;
1348 data = host->mrq->data;
1349 chan = omap_hsmmc_get_dma_chan(host, data);
1350 if (!data->host_cookie)
1351 dma_unmap_sg(chan->device->dev,
1352 data->sg, data->sg_len,
1353 omap_hsmmc_get_dma_dir(host, data));
1355 req_in_progress = host->req_in_progress;
1356 host->dma_ch = -1;
1357 spin_unlock_irq(&host->irq_lock);
1359 /* If DMA has finished after TC, complete the request */
1360 if (!req_in_progress) {
1361 struct mmc_request *mrq = host->mrq;
1363 host->mrq = NULL;
1364 mmc_request_done(host->mmc, mrq);
1368 static int omap_hsmmc_pre_dma_transfer(struct omap_hsmmc_host *host,
1369 struct mmc_data *data,
1370 struct omap_hsmmc_next *next,
1371 struct dma_chan *chan)
1373 int dma_len;
1375 if (!next && data->host_cookie &&
1376 data->host_cookie != host->next_data.cookie) {
1377 dev_warn(host->dev, "[%s] invalid cookie: data->host_cookie %d"
1378 " host->next_data.cookie %d\n",
1379 __func__, data->host_cookie, host->next_data.cookie);
1380 data->host_cookie = 0;
1383 /* Check if next job is already prepared */
1384 if (next || data->host_cookie != host->next_data.cookie) {
1385 dma_len = dma_map_sg(chan->device->dev, data->sg, data->sg_len,
1386 omap_hsmmc_get_dma_dir(host, data));
1388 } else {
1389 dma_len = host->next_data.dma_len;
1390 host->next_data.dma_len = 0;
1394 if (dma_len == 0)
1395 return -EINVAL;
1397 if (next) {
1398 next->dma_len = dma_len;
1399 data->host_cookie = ++next->cookie < 0 ? 1 : next->cookie;
1400 } else
1401 host->dma_len = dma_len;
1403 return 0;
1407 * Routine to configure and start DMA for the MMC card
1409 static int omap_hsmmc_setup_dma_transfer(struct omap_hsmmc_host *host,
1410 struct mmc_request *req)
1412 struct dma_slave_config cfg;
1413 struct dma_async_tx_descriptor *tx;
1414 int ret = 0, i;
1415 struct mmc_data *data = req->data;
1416 struct dma_chan *chan;
1418 /* Sanity check: all the SG entries must be aligned by block size. */
1419 for (i = 0; i < data->sg_len; i++) {
1420 struct scatterlist *sgl;
1422 sgl = data->sg + i;
1423 if (sgl->length % data->blksz)
1424 return -EINVAL;
1426 if ((data->blksz % 4) != 0)
1427 /* REVISIT: The MMC buffer increments only when MSB is written.
1428 * Return error for blksz which is non multiple of four.
1430 return -EINVAL;
1432 BUG_ON(host->dma_ch != -1);
1434 chan = omap_hsmmc_get_dma_chan(host, data);
1436 cfg.src_addr = host->mapbase + OMAP_HSMMC_DATA;
1437 cfg.dst_addr = host->mapbase + OMAP_HSMMC_DATA;
1438 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
1439 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
1440 cfg.src_maxburst = data->blksz / 4;
1441 cfg.dst_maxburst = data->blksz / 4;
1443 ret = dmaengine_slave_config(chan, &cfg);
1444 if (ret)
1445 return ret;
1447 ret = omap_hsmmc_pre_dma_transfer(host, data, NULL, chan);
1448 if (ret)
1449 return ret;
1451 tx = dmaengine_prep_slave_sg(chan, data->sg, data->sg_len,
1452 data->flags & MMC_DATA_WRITE ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM,
1453 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1454 if (!tx) {
1455 dev_err(mmc_dev(host->mmc), "prep_slave_sg() failed\n");
1456 /* FIXME: cleanup */
1457 return -1;
1460 tx->callback = omap_hsmmc_dma_callback;
1461 tx->callback_param = host;
1463 /* Does not fail */
1464 dmaengine_submit(tx);
1466 host->dma_ch = 1;
1468 return 0;
1471 static void set_data_timeout(struct omap_hsmmc_host *host,
1472 unsigned int timeout_ns,
1473 unsigned int timeout_clks)
1475 unsigned int timeout, cycle_ns;
1476 uint32_t reg, clkd, dto = 0;
1478 reg = OMAP_HSMMC_READ(host->base, SYSCTL);
1479 clkd = (reg & CLKD_MASK) >> CLKD_SHIFT;
1480 if (clkd == 0)
1481 clkd = 1;
1483 cycle_ns = 1000000000 / (host->clk_rate / clkd);
1484 timeout = timeout_ns / cycle_ns;
1485 timeout += timeout_clks;
1486 if (timeout) {
1487 while ((timeout & 0x80000000) == 0) {
1488 dto += 1;
1489 timeout <<= 1;
1491 dto = 31 - dto;
1492 timeout <<= 1;
1493 if (timeout && dto)
1494 dto += 1;
1495 if (dto >= 13)
1496 dto -= 13;
1497 else
1498 dto = 0;
1499 if (dto > 14)
1500 dto = 14;
1503 reg &= ~DTO_MASK;
1504 reg |= dto << DTO_SHIFT;
1505 OMAP_HSMMC_WRITE(host->base, SYSCTL, reg);
1508 static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host)
1510 struct mmc_request *req = host->mrq;
1511 struct dma_chan *chan;
1513 if (!req->data)
1514 return;
1515 OMAP_HSMMC_WRITE(host->base, BLK, (req->data->blksz)
1516 | (req->data->blocks << 16));
1517 set_data_timeout(host, req->data->timeout_ns,
1518 req->data->timeout_clks);
1519 chan = omap_hsmmc_get_dma_chan(host, req->data);
1520 dma_async_issue_pending(chan);
1524 * Configure block length for MMC/SD cards and initiate the transfer.
1526 static int
1527 omap_hsmmc_prepare_data(struct omap_hsmmc_host *host, struct mmc_request *req)
1529 int ret;
1530 host->data = req->data;
1532 if (req->data == NULL) {
1533 OMAP_HSMMC_WRITE(host->base, BLK, 0);
1535 * Set an arbitrary 100ms data timeout for commands with
1536 * busy signal.
1538 if (req->cmd->flags & MMC_RSP_BUSY)
1539 set_data_timeout(host, 100000000U, 0);
1540 return 0;
1543 if (host->use_dma) {
1544 ret = omap_hsmmc_setup_dma_transfer(host, req);
1545 if (ret != 0) {
1546 dev_err(mmc_dev(host->mmc), "MMC start dma failure\n");
1547 return ret;
1550 return 0;
1553 static void omap_hsmmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
1554 int err)
1556 struct omap_hsmmc_host *host = mmc_priv(mmc);
1557 struct mmc_data *data = mrq->data;
1559 if (host->use_dma && data->host_cookie) {
1560 struct dma_chan *c = omap_hsmmc_get_dma_chan(host, data);
1562 dma_unmap_sg(c->device->dev, data->sg, data->sg_len,
1563 omap_hsmmc_get_dma_dir(host, data));
1564 data->host_cookie = 0;
1568 static void omap_hsmmc_pre_req(struct mmc_host *mmc, struct mmc_request *mrq,
1569 bool is_first_req)
1571 struct omap_hsmmc_host *host = mmc_priv(mmc);
1573 if (mrq->data->host_cookie) {
1574 mrq->data->host_cookie = 0;
1575 return ;
1578 if (host->use_dma) {
1579 struct dma_chan *c = omap_hsmmc_get_dma_chan(host, mrq->data);
1581 if (omap_hsmmc_pre_dma_transfer(host, mrq->data,
1582 &host->next_data, c))
1583 mrq->data->host_cookie = 0;
1588 * Request function. for read/write operation
1590 static void omap_hsmmc_request(struct mmc_host *mmc, struct mmc_request *req)
1592 struct omap_hsmmc_host *host = mmc_priv(mmc);
1593 int err;
1595 BUG_ON(host->req_in_progress);
1596 BUG_ON(host->dma_ch != -1);
1597 if (host->protect_card) {
1598 if (host->reqs_blocked < 3) {
1600 * Ensure the controller is left in a consistent
1601 * state by resetting the command and data state
1602 * machines.
1604 omap_hsmmc_reset_controller_fsm(host, SRD);
1605 omap_hsmmc_reset_controller_fsm(host, SRC);
1606 host->reqs_blocked += 1;
1608 req->cmd->error = -EBADF;
1609 if (req->data)
1610 req->data->error = -EBADF;
1611 req->cmd->retries = 0;
1612 mmc_request_done(mmc, req);
1613 return;
1614 } else if (host->reqs_blocked)
1615 host->reqs_blocked = 0;
1616 WARN_ON(host->mrq != NULL);
1617 host->mrq = req;
1618 host->clk_rate = clk_get_rate(host->fclk);
1619 err = omap_hsmmc_prepare_data(host, req);
1620 if (err) {
1621 req->cmd->error = err;
1622 if (req->data)
1623 req->data->error = err;
1624 host->mrq = NULL;
1625 mmc_request_done(mmc, req);
1626 return;
1628 if (req->sbc && !(host->flags & AUTO_CMD23)) {
1629 omap_hsmmc_start_command(host, req->sbc, NULL);
1630 return;
1633 omap_hsmmc_start_dma_transfer(host);
1634 omap_hsmmc_start_command(host, req->cmd, req->data);
1637 /* Routine to configure clock values. Exposed API to core */
1638 static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1640 struct omap_hsmmc_host *host = mmc_priv(mmc);
1641 int do_send_init_stream = 0;
1643 if (ios->power_mode != host->power_mode) {
1644 switch (ios->power_mode) {
1645 case MMC_POWER_OFF:
1646 omap_hsmmc_set_power(host, 0, 0);
1647 break;
1648 case MMC_POWER_UP:
1649 omap_hsmmc_set_power(host, 1, ios->vdd);
1650 break;
1651 case MMC_POWER_ON:
1652 do_send_init_stream = 1;
1653 break;
1655 host->power_mode = ios->power_mode;
1658 /* FIXME: set registers based only on changes to ios */
1660 omap_hsmmc_set_bus_width(host);
1662 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
1663 /* Only MMC1 can interface at 3V without some flavor
1664 * of external transceiver; but they all handle 1.8V.
1666 if ((OMAP_HSMMC_READ(host->base, HCTL) & SDVSDET) &&
1667 (ios->vdd == DUAL_VOLT_OCR_BIT)) {
1669 * The mmc_select_voltage fn of the core does
1670 * not seem to set the power_mode to
1671 * MMC_POWER_UP upon recalculating the voltage.
1672 * vdd 1.8v.
1674 if (omap_hsmmc_switch_opcond(host, ios->vdd) != 0)
1675 dev_dbg(mmc_dev(host->mmc),
1676 "Switch operation failed\n");
1680 omap_hsmmc_set_clock(host);
1682 if (do_send_init_stream)
1683 send_init_stream(host);
1685 omap_hsmmc_set_bus_mode(host);
1688 static int omap_hsmmc_get_cd(struct mmc_host *mmc)
1690 struct omap_hsmmc_host *host = mmc_priv(mmc);
1692 if (!host->card_detect)
1693 return -ENOSYS;
1694 return host->card_detect(host->dev);
1697 static void omap_hsmmc_init_card(struct mmc_host *mmc, struct mmc_card *card)
1699 struct omap_hsmmc_host *host = mmc_priv(mmc);
1701 if (mmc_pdata(host)->init_card)
1702 mmc_pdata(host)->init_card(card);
1705 static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
1707 struct omap_hsmmc_host *host = mmc_priv(mmc);
1708 u32 irq_mask, con;
1709 unsigned long flags;
1711 spin_lock_irqsave(&host->irq_lock, flags);
1713 con = OMAP_HSMMC_READ(host->base, CON);
1714 irq_mask = OMAP_HSMMC_READ(host->base, ISE);
1715 if (enable) {
1716 host->flags |= HSMMC_SDIO_IRQ_ENABLED;
1717 irq_mask |= CIRQ_EN;
1718 con |= CTPL | CLKEXTFREE;
1719 } else {
1720 host->flags &= ~HSMMC_SDIO_IRQ_ENABLED;
1721 irq_mask &= ~CIRQ_EN;
1722 con &= ~(CTPL | CLKEXTFREE);
1724 OMAP_HSMMC_WRITE(host->base, CON, con);
1725 OMAP_HSMMC_WRITE(host->base, IE, irq_mask);
1728 * if enable, piggy back detection on current request
1729 * but always disable immediately
1731 if (!host->req_in_progress || !enable)
1732 OMAP_HSMMC_WRITE(host->base, ISE, irq_mask);
1734 /* flush posted write */
1735 OMAP_HSMMC_READ(host->base, IE);
1737 spin_unlock_irqrestore(&host->irq_lock, flags);
1740 static int omap_hsmmc_configure_wake_irq(struct omap_hsmmc_host *host)
1742 int ret;
1745 * For omaps with wake-up path, wakeirq will be irq from pinctrl and
1746 * for other omaps, wakeirq will be from GPIO (dat line remuxed to
1747 * gpio). wakeirq is needed to detect sdio irq in runtime suspend state
1748 * with functional clock disabled.
1750 if (!host->dev->of_node || !host->wake_irq)
1751 return -ENODEV;
1753 ret = dev_pm_set_dedicated_wake_irq(host->dev, host->wake_irq);
1754 if (ret) {
1755 dev_err(mmc_dev(host->mmc), "Unable to request wake IRQ\n");
1756 goto err;
1760 * Some omaps don't have wake-up path from deeper idle states
1761 * and need to remux SDIO DAT1 to GPIO for wake-up from idle.
1763 if (host->pdata->controller_flags & OMAP_HSMMC_SWAKEUP_MISSING) {
1764 struct pinctrl *p = devm_pinctrl_get(host->dev);
1765 if (!p) {
1766 ret = -ENODEV;
1767 goto err_free_irq;
1769 if (IS_ERR(pinctrl_lookup_state(p, PINCTRL_STATE_DEFAULT))) {
1770 dev_info(host->dev, "missing default pinctrl state\n");
1771 devm_pinctrl_put(p);
1772 ret = -EINVAL;
1773 goto err_free_irq;
1776 if (IS_ERR(pinctrl_lookup_state(p, PINCTRL_STATE_IDLE))) {
1777 dev_info(host->dev, "missing idle pinctrl state\n");
1778 devm_pinctrl_put(p);
1779 ret = -EINVAL;
1780 goto err_free_irq;
1782 devm_pinctrl_put(p);
1785 OMAP_HSMMC_WRITE(host->base, HCTL,
1786 OMAP_HSMMC_READ(host->base, HCTL) | IWE);
1787 return 0;
1789 err_free_irq:
1790 dev_pm_clear_wake_irq(host->dev);
1791 err:
1792 dev_warn(host->dev, "no SDIO IRQ support, falling back to polling\n");
1793 host->wake_irq = 0;
1794 return ret;
1797 static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host)
1799 u32 hctl, capa, value;
1801 /* Only MMC1 supports 3.0V */
1802 if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) {
1803 hctl = SDVS30;
1804 capa = VS30 | VS18;
1805 } else {
1806 hctl = SDVS18;
1807 capa = VS18;
1810 value = OMAP_HSMMC_READ(host->base, HCTL) & ~SDVS_MASK;
1811 OMAP_HSMMC_WRITE(host->base, HCTL, value | hctl);
1813 value = OMAP_HSMMC_READ(host->base, CAPA);
1814 OMAP_HSMMC_WRITE(host->base, CAPA, value | capa);
1816 /* Set SD bus power bit */
1817 set_sd_bus_power(host);
1820 static int omap_hsmmc_multi_io_quirk(struct mmc_card *card,
1821 unsigned int direction, int blk_size)
1823 /* This controller can't do multiblock reads due to hw bugs */
1824 if (direction == MMC_DATA_READ)
1825 return 1;
1827 return blk_size;
1830 static struct mmc_host_ops omap_hsmmc_ops = {
1831 .post_req = omap_hsmmc_post_req,
1832 .pre_req = omap_hsmmc_pre_req,
1833 .request = omap_hsmmc_request,
1834 .set_ios = omap_hsmmc_set_ios,
1835 .get_cd = omap_hsmmc_get_cd,
1836 .get_ro = mmc_gpio_get_ro,
1837 .init_card = omap_hsmmc_init_card,
1838 .enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
1841 #ifdef CONFIG_DEBUG_FS
1843 static int omap_hsmmc_regs_show(struct seq_file *s, void *data)
1845 struct mmc_host *mmc = s->private;
1846 struct omap_hsmmc_host *host = mmc_priv(mmc);
1848 seq_printf(s, "mmc%d:\n", mmc->index);
1849 seq_printf(s, "sdio irq mode\t%s\n",
1850 (mmc->caps & MMC_CAP_SDIO_IRQ) ? "interrupt" : "polling");
1852 if (mmc->caps & MMC_CAP_SDIO_IRQ) {
1853 seq_printf(s, "sdio irq \t%s\n",
1854 (host->flags & HSMMC_SDIO_IRQ_ENABLED) ? "enabled"
1855 : "disabled");
1857 seq_printf(s, "ctx_loss:\t%d\n", host->context_loss);
1859 pm_runtime_get_sync(host->dev);
1860 seq_puts(s, "\nregs:\n");
1861 seq_printf(s, "CON:\t\t0x%08x\n",
1862 OMAP_HSMMC_READ(host->base, CON));
1863 seq_printf(s, "PSTATE:\t\t0x%08x\n",
1864 OMAP_HSMMC_READ(host->base, PSTATE));
1865 seq_printf(s, "HCTL:\t\t0x%08x\n",
1866 OMAP_HSMMC_READ(host->base, HCTL));
1867 seq_printf(s, "SYSCTL:\t\t0x%08x\n",
1868 OMAP_HSMMC_READ(host->base, SYSCTL));
1869 seq_printf(s, "IE:\t\t0x%08x\n",
1870 OMAP_HSMMC_READ(host->base, IE));
1871 seq_printf(s, "ISE:\t\t0x%08x\n",
1872 OMAP_HSMMC_READ(host->base, ISE));
1873 seq_printf(s, "CAPA:\t\t0x%08x\n",
1874 OMAP_HSMMC_READ(host->base, CAPA));
1876 pm_runtime_mark_last_busy(host->dev);
1877 pm_runtime_put_autosuspend(host->dev);
1879 return 0;
1882 static int omap_hsmmc_regs_open(struct inode *inode, struct file *file)
1884 return single_open(file, omap_hsmmc_regs_show, inode->i_private);
1887 static const struct file_operations mmc_regs_fops = {
1888 .open = omap_hsmmc_regs_open,
1889 .read = seq_read,
1890 .llseek = seq_lseek,
1891 .release = single_release,
1894 static void omap_hsmmc_debugfs(struct mmc_host *mmc)
1896 if (mmc->debugfs_root)
1897 debugfs_create_file("regs", S_IRUSR, mmc->debugfs_root,
1898 mmc, &mmc_regs_fops);
1901 #else
1903 static void omap_hsmmc_debugfs(struct mmc_host *mmc)
1907 #endif
1909 #ifdef CONFIG_OF
1910 static const struct omap_mmc_of_data omap3_pre_es3_mmc_of_data = {
1911 /* See 35xx errata 2.1.1.128 in SPRZ278F */
1912 .controller_flags = OMAP_HSMMC_BROKEN_MULTIBLOCK_READ,
1915 static const struct omap_mmc_of_data omap4_mmc_of_data = {
1916 .reg_offset = 0x100,
1918 static const struct omap_mmc_of_data am33xx_mmc_of_data = {
1919 .reg_offset = 0x100,
1920 .controller_flags = OMAP_HSMMC_SWAKEUP_MISSING,
1923 static const struct of_device_id omap_mmc_of_match[] = {
1925 .compatible = "ti,omap2-hsmmc",
1928 .compatible = "ti,omap3-pre-es3-hsmmc",
1929 .data = &omap3_pre_es3_mmc_of_data,
1932 .compatible = "ti,omap3-hsmmc",
1935 .compatible = "ti,omap4-hsmmc",
1936 .data = &omap4_mmc_of_data,
1939 .compatible = "ti,am33xx-hsmmc",
1940 .data = &am33xx_mmc_of_data,
1944 MODULE_DEVICE_TABLE(of, omap_mmc_of_match);
1946 static struct omap_hsmmc_platform_data *of_get_hsmmc_pdata(struct device *dev)
1948 struct omap_hsmmc_platform_data *pdata, *legacy;
1949 struct device_node *np = dev->of_node;
1951 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
1952 if (!pdata)
1953 return ERR_PTR(-ENOMEM); /* out of memory */
1955 legacy = dev_get_platdata(dev);
1956 if (legacy && legacy->name)
1957 pdata->name = legacy->name;
1959 if (of_find_property(np, "ti,dual-volt", NULL))
1960 pdata->controller_flags |= OMAP_HSMMC_SUPPORTS_DUAL_VOLT;
1962 pdata->gpio_cd = -EINVAL;
1963 pdata->gpio_cod = -EINVAL;
1964 pdata->gpio_wp = -EINVAL;
1966 if (of_find_property(np, "ti,non-removable", NULL)) {
1967 pdata->nonremovable = true;
1968 pdata->no_regulator_off_init = true;
1971 if (of_find_property(np, "ti,needs-special-reset", NULL))
1972 pdata->features |= HSMMC_HAS_UPDATED_RESET;
1974 if (of_find_property(np, "ti,needs-special-hs-handling", NULL))
1975 pdata->features |= HSMMC_HAS_HSPE_SUPPORT;
1977 return pdata;
1979 #else
1980 static inline struct omap_hsmmc_platform_data
1981 *of_get_hsmmc_pdata(struct device *dev)
1983 return ERR_PTR(-EINVAL);
1985 #endif
1987 static int omap_hsmmc_probe(struct platform_device *pdev)
1989 struct omap_hsmmc_platform_data *pdata = pdev->dev.platform_data;
1990 struct mmc_host *mmc;
1991 struct omap_hsmmc_host *host = NULL;
1992 struct resource *res;
1993 int ret, irq;
1994 const struct of_device_id *match;
1995 const struct omap_mmc_of_data *data;
1996 void __iomem *base;
1998 match = of_match_device(of_match_ptr(omap_mmc_of_match), &pdev->dev);
1999 if (match) {
2000 pdata = of_get_hsmmc_pdata(&pdev->dev);
2002 if (IS_ERR(pdata))
2003 return PTR_ERR(pdata);
2005 if (match->data) {
2006 data = match->data;
2007 pdata->reg_offset = data->reg_offset;
2008 pdata->controller_flags |= data->controller_flags;
2012 if (pdata == NULL) {
2013 dev_err(&pdev->dev, "Platform Data is missing\n");
2014 return -ENXIO;
2017 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2018 irq = platform_get_irq(pdev, 0);
2019 if (res == NULL || irq < 0)
2020 return -ENXIO;
2022 base = devm_ioremap_resource(&pdev->dev, res);
2023 if (IS_ERR(base))
2024 return PTR_ERR(base);
2026 mmc = mmc_alloc_host(sizeof(struct omap_hsmmc_host), &pdev->dev);
2027 if (!mmc) {
2028 ret = -ENOMEM;
2029 goto err;
2032 ret = mmc_of_parse(mmc);
2033 if (ret)
2034 goto err1;
2036 host = mmc_priv(mmc);
2037 host->mmc = mmc;
2038 host->pdata = pdata;
2039 host->dev = &pdev->dev;
2040 host->use_dma = 1;
2041 host->dma_ch = -1;
2042 host->irq = irq;
2043 host->mapbase = res->start + pdata->reg_offset;
2044 host->base = base + pdata->reg_offset;
2045 host->power_mode = MMC_POWER_OFF;
2046 host->next_data.cookie = 1;
2047 host->pbias_enabled = 0;
2048 host->vqmmc_enabled = 0;
2050 ret = omap_hsmmc_gpio_init(mmc, host, pdata);
2051 if (ret)
2052 goto err_gpio;
2054 platform_set_drvdata(pdev, host);
2056 if (pdev->dev.of_node)
2057 host->wake_irq = irq_of_parse_and_map(pdev->dev.of_node, 1);
2059 mmc->ops = &omap_hsmmc_ops;
2061 mmc->f_min = OMAP_MMC_MIN_CLOCK;
2063 if (pdata->max_freq > 0)
2064 mmc->f_max = pdata->max_freq;
2065 else if (mmc->f_max == 0)
2066 mmc->f_max = OMAP_MMC_MAX_CLOCK;
2068 spin_lock_init(&host->irq_lock);
2070 host->fclk = devm_clk_get(&pdev->dev, "fck");
2071 if (IS_ERR(host->fclk)) {
2072 ret = PTR_ERR(host->fclk);
2073 host->fclk = NULL;
2074 goto err1;
2077 if (host->pdata->controller_flags & OMAP_HSMMC_BROKEN_MULTIBLOCK_READ) {
2078 dev_info(&pdev->dev, "multiblock reads disabled due to 35xx erratum 2.1.1.128; MMC read performance may suffer\n");
2079 omap_hsmmc_ops.multi_io_quirk = omap_hsmmc_multi_io_quirk;
2082 device_init_wakeup(&pdev->dev, true);
2083 pm_runtime_enable(host->dev);
2084 pm_runtime_get_sync(host->dev);
2085 pm_runtime_set_autosuspend_delay(host->dev, MMC_AUTOSUSPEND_DELAY);
2086 pm_runtime_use_autosuspend(host->dev);
2088 omap_hsmmc_context_save(host);
2090 host->dbclk = devm_clk_get(&pdev->dev, "mmchsdb_fck");
2092 * MMC can still work without debounce clock.
2094 if (IS_ERR(host->dbclk)) {
2095 host->dbclk = NULL;
2096 } else if (clk_prepare_enable(host->dbclk) != 0) {
2097 dev_warn(mmc_dev(host->mmc), "Failed to enable debounce clk\n");
2098 host->dbclk = NULL;
2101 /* Since we do only SG emulation, we can have as many segs
2102 * as we want. */
2103 mmc->max_segs = 1024;
2105 mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
2106 mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
2107 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
2108 mmc->max_seg_size = mmc->max_req_size;
2110 mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
2111 MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_ERASE;
2113 mmc->caps |= mmc_pdata(host)->caps;
2114 if (mmc->caps & MMC_CAP_8_BIT_DATA)
2115 mmc->caps |= MMC_CAP_4_BIT_DATA;
2117 if (mmc_pdata(host)->nonremovable)
2118 mmc->caps |= MMC_CAP_NONREMOVABLE;
2120 mmc->pm_caps |= mmc_pdata(host)->pm_caps;
2122 omap_hsmmc_conf_bus_power(host);
2124 host->rx_chan = dma_request_chan(&pdev->dev, "rx");
2125 if (IS_ERR(host->rx_chan)) {
2126 dev_err(mmc_dev(host->mmc), "RX DMA channel request failed\n");
2127 ret = PTR_ERR(host->rx_chan);
2128 goto err_irq;
2131 host->tx_chan = dma_request_chan(&pdev->dev, "tx");
2132 if (IS_ERR(host->tx_chan)) {
2133 dev_err(mmc_dev(host->mmc), "TX DMA channel request failed\n");
2134 ret = PTR_ERR(host->tx_chan);
2135 goto err_irq;
2138 /* Request IRQ for MMC operations */
2139 ret = devm_request_irq(&pdev->dev, host->irq, omap_hsmmc_irq, 0,
2140 mmc_hostname(mmc), host);
2141 if (ret) {
2142 dev_err(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n");
2143 goto err_irq;
2146 ret = omap_hsmmc_reg_get(host);
2147 if (ret)
2148 goto err_irq;
2150 mmc->ocr_avail = mmc_pdata(host)->ocr_mask;
2152 omap_hsmmc_disable_irq(host);
2155 * For now, only support SDIO interrupt if we have a separate
2156 * wake-up interrupt configured from device tree. This is because
2157 * the wake-up interrupt is needed for idle state and some
2158 * platforms need special quirks. And we don't want to add new
2159 * legacy mux platform init code callbacks any longer as we
2160 * are moving to DT based booting anyways.
2162 ret = omap_hsmmc_configure_wake_irq(host);
2163 if (!ret)
2164 mmc->caps |= MMC_CAP_SDIO_IRQ;
2166 omap_hsmmc_protect_card(host);
2168 mmc_add_host(mmc);
2170 if (mmc_pdata(host)->name != NULL) {
2171 ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name);
2172 if (ret < 0)
2173 goto err_slot_name;
2175 if (host->get_cover_state) {
2176 ret = device_create_file(&mmc->class_dev,
2177 &dev_attr_cover_switch);
2178 if (ret < 0)
2179 goto err_slot_name;
2182 omap_hsmmc_debugfs(mmc);
2183 pm_runtime_mark_last_busy(host->dev);
2184 pm_runtime_put_autosuspend(host->dev);
2186 return 0;
2188 err_slot_name:
2189 mmc_remove_host(mmc);
2190 err_irq:
2191 device_init_wakeup(&pdev->dev, false);
2192 if (!IS_ERR_OR_NULL(host->tx_chan))
2193 dma_release_channel(host->tx_chan);
2194 if (!IS_ERR_OR_NULL(host->rx_chan))
2195 dma_release_channel(host->rx_chan);
2196 pm_runtime_dont_use_autosuspend(host->dev);
2197 pm_runtime_put_sync(host->dev);
2198 pm_runtime_disable(host->dev);
2199 if (host->dbclk)
2200 clk_disable_unprepare(host->dbclk);
2201 err1:
2202 err_gpio:
2203 mmc_free_host(mmc);
2204 err:
2205 return ret;
2208 static int omap_hsmmc_remove(struct platform_device *pdev)
2210 struct omap_hsmmc_host *host = platform_get_drvdata(pdev);
2212 pm_runtime_get_sync(host->dev);
2213 mmc_remove_host(host->mmc);
2215 dma_release_channel(host->tx_chan);
2216 dma_release_channel(host->rx_chan);
2218 pm_runtime_dont_use_autosuspend(host->dev);
2219 pm_runtime_put_sync(host->dev);
2220 pm_runtime_disable(host->dev);
2221 device_init_wakeup(&pdev->dev, false);
2222 if (host->dbclk)
2223 clk_disable_unprepare(host->dbclk);
2225 mmc_free_host(host->mmc);
2227 return 0;
2230 #ifdef CONFIG_PM_SLEEP
2231 static int omap_hsmmc_suspend(struct device *dev)
2233 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
2235 if (!host)
2236 return 0;
2238 pm_runtime_get_sync(host->dev);
2240 if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) {
2241 OMAP_HSMMC_WRITE(host->base, ISE, 0);
2242 OMAP_HSMMC_WRITE(host->base, IE, 0);
2243 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
2244 OMAP_HSMMC_WRITE(host->base, HCTL,
2245 OMAP_HSMMC_READ(host->base, HCTL) & ~SDBP);
2248 if (host->dbclk)
2249 clk_disable_unprepare(host->dbclk);
2251 pm_runtime_put_sync(host->dev);
2252 return 0;
2255 /* Routine to resume the MMC device */
2256 static int omap_hsmmc_resume(struct device *dev)
2258 struct omap_hsmmc_host *host = dev_get_drvdata(dev);
2260 if (!host)
2261 return 0;
2263 pm_runtime_get_sync(host->dev);
2265 if (host->dbclk)
2266 clk_prepare_enable(host->dbclk);
2268 if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER))
2269 omap_hsmmc_conf_bus_power(host);
2271 omap_hsmmc_protect_card(host);
2272 pm_runtime_mark_last_busy(host->dev);
2273 pm_runtime_put_autosuspend(host->dev);
2274 return 0;
2276 #endif
2278 static int omap_hsmmc_runtime_suspend(struct device *dev)
2280 struct omap_hsmmc_host *host;
2281 unsigned long flags;
2282 int ret = 0;
2284 host = platform_get_drvdata(to_platform_device(dev));
2285 omap_hsmmc_context_save(host);
2286 dev_dbg(dev, "disabled\n");
2288 spin_lock_irqsave(&host->irq_lock, flags);
2289 if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
2290 (host->flags & HSMMC_SDIO_IRQ_ENABLED)) {
2291 /* disable sdio irq handling to prevent race */
2292 OMAP_HSMMC_WRITE(host->base, ISE, 0);
2293 OMAP_HSMMC_WRITE(host->base, IE, 0);
2295 if (!(OMAP_HSMMC_READ(host->base, PSTATE) & DLEV_DAT(1))) {
2297 * dat1 line low, pending sdio irq
2298 * race condition: possible irq handler running on
2299 * multi-core, abort
2301 dev_dbg(dev, "pending sdio irq, abort suspend\n");
2302 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
2303 OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
2304 OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
2305 pm_runtime_mark_last_busy(dev);
2306 ret = -EBUSY;
2307 goto abort;
2310 pinctrl_pm_select_idle_state(dev);
2311 } else {
2312 pinctrl_pm_select_idle_state(dev);
2315 abort:
2316 spin_unlock_irqrestore(&host->irq_lock, flags);
2317 return ret;
2320 static int omap_hsmmc_runtime_resume(struct device *dev)
2322 struct omap_hsmmc_host *host;
2323 unsigned long flags;
2325 host = platform_get_drvdata(to_platform_device(dev));
2326 omap_hsmmc_context_restore(host);
2327 dev_dbg(dev, "enabled\n");
2329 spin_lock_irqsave(&host->irq_lock, flags);
2330 if ((host->mmc->caps & MMC_CAP_SDIO_IRQ) &&
2331 (host->flags & HSMMC_SDIO_IRQ_ENABLED)) {
2333 pinctrl_pm_select_default_state(host->dev);
2335 /* irq lost, if pinmux incorrect */
2336 OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR);
2337 OMAP_HSMMC_WRITE(host->base, ISE, CIRQ_EN);
2338 OMAP_HSMMC_WRITE(host->base, IE, CIRQ_EN);
2339 } else {
2340 pinctrl_pm_select_default_state(host->dev);
2342 spin_unlock_irqrestore(&host->irq_lock, flags);
2343 return 0;
2346 static struct dev_pm_ops omap_hsmmc_dev_pm_ops = {
2347 SET_SYSTEM_SLEEP_PM_OPS(omap_hsmmc_suspend, omap_hsmmc_resume)
2348 .runtime_suspend = omap_hsmmc_runtime_suspend,
2349 .runtime_resume = omap_hsmmc_runtime_resume,
2352 static struct platform_driver omap_hsmmc_driver = {
2353 .probe = omap_hsmmc_probe,
2354 .remove = omap_hsmmc_remove,
2355 .driver = {
2356 .name = DRIVER_NAME,
2357 .pm = &omap_hsmmc_dev_pm_ops,
2358 .of_match_table = of_match_ptr(omap_mmc_of_match),
2362 module_platform_driver(omap_hsmmc_driver);
2363 MODULE_DESCRIPTION("OMAP High Speed Multimedia Card driver");
2364 MODULE_LICENSE("GPL");
2365 MODULE_ALIAS("platform:" DRIVER_NAME);
2366 MODULE_AUTHOR("Texas Instruments Inc");