bna: remove oper_state_cbfn from struct bna_rxf
[linux/fpc-iii.git] / drivers / usb / serial / ch341.c
blobc73808f095bba2b3f71ff2885778e7dd6f0ddd8d
1 /*
2 * Copyright 2007, Frank A Kingswood <frank@kingswood-consulting.co.uk>
3 * Copyright 2007, Werner Cornelius <werner@cornelius-consult.de>
4 * Copyright 2009, Boris Hajduk <boris@hajduk.org>
6 * ch341.c implements a serial port driver for the Winchiphead CH341.
8 * The CH341 device can be used to implement an RS232 asynchronous
9 * serial port, an IEEE-1284 parallel printer port or a memory-like
10 * interface. In all cases the CH341 supports an I2C interface as well.
11 * This driver only supports the asynchronous serial interface.
13 * This program is free software; you can redistribute it and/or
14 * modify it under the terms of the GNU General Public License version
15 * 2 as published by the Free Software Foundation.
18 #include <linux/kernel.h>
19 #include <linux/tty.h>
20 #include <linux/module.h>
21 #include <linux/slab.h>
22 #include <linux/usb.h>
23 #include <linux/usb/serial.h>
24 #include <linux/serial.h>
25 #include <asm/unaligned.h>
27 #define DEFAULT_BAUD_RATE 9600
28 #define DEFAULT_TIMEOUT 1000
30 /* flags for IO-Bits */
31 #define CH341_BIT_RTS (1 << 6)
32 #define CH341_BIT_DTR (1 << 5)
34 /******************************/
35 /* interrupt pipe definitions */
36 /******************************/
37 /* always 4 interrupt bytes */
38 /* first irq byte normally 0x08 */
39 /* second irq byte base 0x7d + below */
40 /* third irq byte base 0x94 + below */
41 /* fourth irq byte normally 0xee */
43 /* second interrupt byte */
44 #define CH341_MULT_STAT 0x04 /* multiple status since last interrupt event */
46 /* status returned in third interrupt answer byte, inverted in data
47 from irq */
48 #define CH341_BIT_CTS 0x01
49 #define CH341_BIT_DSR 0x02
50 #define CH341_BIT_RI 0x04
51 #define CH341_BIT_DCD 0x08
52 #define CH341_BITS_MODEM_STAT 0x0f /* all bits */
54 /*******************************/
55 /* baudrate calculation factor */
56 /*******************************/
57 #define CH341_BAUDBASE_FACTOR 1532620800
58 #define CH341_BAUDBASE_DIVMAX 3
60 /* Break support - the information used to implement this was gleaned from
61 * the Net/FreeBSD uchcom.c driver by Takanori Watanabe. Domo arigato.
64 #define CH341_REQ_WRITE_REG 0x9A
65 #define CH341_REQ_READ_REG 0x95
66 #define CH341_REG_BREAK1 0x05
67 #define CH341_REG_BREAK2 0x18
68 #define CH341_NBREAK_BITS_REG1 0x01
69 #define CH341_NBREAK_BITS_REG2 0x40
72 static const struct usb_device_id id_table[] = {
73 { USB_DEVICE(0x4348, 0x5523) },
74 { USB_DEVICE(0x1a86, 0x7523) },
75 { USB_DEVICE(0x1a86, 0x5523) },
76 { },
78 MODULE_DEVICE_TABLE(usb, id_table);
80 struct ch341_private {
81 spinlock_t lock; /* access lock */
82 unsigned baud_rate; /* set baud rate */
83 u8 line_control; /* set line control value RTS/DTR */
84 u8 line_status; /* active status of modem control inputs */
87 static void ch341_set_termios(struct tty_struct *tty,
88 struct usb_serial_port *port,
89 struct ktermios *old_termios);
91 static int ch341_control_out(struct usb_device *dev, u8 request,
92 u16 value, u16 index)
94 int r;
96 dev_dbg(&dev->dev, "ch341_control_out(%02x,%02x,%04x,%04x)\n",
97 USB_DIR_OUT|0x40, (int)request, (int)value, (int)index);
99 r = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request,
100 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
101 value, index, NULL, 0, DEFAULT_TIMEOUT);
103 return r;
106 static int ch341_control_in(struct usb_device *dev,
107 u8 request, u16 value, u16 index,
108 char *buf, unsigned bufsize)
110 int r;
112 dev_dbg(&dev->dev, "ch341_control_in(%02x,%02x,%04x,%04x,%p,%u)\n",
113 USB_DIR_IN|0x40, (int)request, (int)value, (int)index, buf,
114 (int)bufsize);
116 r = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request,
117 USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
118 value, index, buf, bufsize, DEFAULT_TIMEOUT);
119 return r;
122 static int ch341_set_baudrate(struct usb_device *dev,
123 struct ch341_private *priv)
125 short a, b;
126 int r;
127 unsigned long factor;
128 short divisor;
130 if (!priv->baud_rate)
131 return -EINVAL;
132 factor = (CH341_BAUDBASE_FACTOR / priv->baud_rate);
133 divisor = CH341_BAUDBASE_DIVMAX;
135 while ((factor > 0xfff0) && divisor) {
136 factor >>= 3;
137 divisor--;
140 if (factor > 0xfff0)
141 return -EINVAL;
143 factor = 0x10000 - factor;
144 a = (factor & 0xff00) | divisor;
145 b = factor & 0xff;
147 r = ch341_control_out(dev, 0x9a, 0x1312, a);
148 if (!r)
149 r = ch341_control_out(dev, 0x9a, 0x0f2c, b);
151 return r;
154 static int ch341_set_handshake(struct usb_device *dev, u8 control)
156 return ch341_control_out(dev, 0xa4, ~control, 0);
159 static int ch341_get_status(struct usb_device *dev, struct ch341_private *priv)
161 char *buffer;
162 int r;
163 const unsigned size = 8;
164 unsigned long flags;
166 buffer = kmalloc(size, GFP_KERNEL);
167 if (!buffer)
168 return -ENOMEM;
170 r = ch341_control_in(dev, 0x95, 0x0706, 0, buffer, size);
171 if (r < 0)
172 goto out;
174 /* setup the private status if available */
175 if (r == 2) {
176 r = 0;
177 spin_lock_irqsave(&priv->lock, flags);
178 priv->line_status = (~(*buffer)) & CH341_BITS_MODEM_STAT;
179 spin_unlock_irqrestore(&priv->lock, flags);
180 } else
181 r = -EPROTO;
183 out: kfree(buffer);
184 return r;
187 /* -------------------------------------------------------------------------- */
189 static int ch341_configure(struct usb_device *dev, struct ch341_private *priv)
191 char *buffer;
192 int r;
193 const unsigned size = 8;
195 buffer = kmalloc(size, GFP_KERNEL);
196 if (!buffer)
197 return -ENOMEM;
199 /* expect two bytes 0x27 0x00 */
200 r = ch341_control_in(dev, 0x5f, 0, 0, buffer, size);
201 if (r < 0)
202 goto out;
204 r = ch341_control_out(dev, 0xa1, 0, 0);
205 if (r < 0)
206 goto out;
208 r = ch341_set_baudrate(dev, priv);
209 if (r < 0)
210 goto out;
212 /* expect two bytes 0x56 0x00 */
213 r = ch341_control_in(dev, 0x95, 0x2518, 0, buffer, size);
214 if (r < 0)
215 goto out;
217 r = ch341_control_out(dev, 0x9a, 0x2518, 0x0050);
218 if (r < 0)
219 goto out;
221 /* expect 0xff 0xee */
222 r = ch341_get_status(dev, priv);
223 if (r < 0)
224 goto out;
226 r = ch341_control_out(dev, 0xa1, 0x501f, 0xd90a);
227 if (r < 0)
228 goto out;
230 r = ch341_set_baudrate(dev, priv);
231 if (r < 0)
232 goto out;
234 r = ch341_set_handshake(dev, priv->line_control);
235 if (r < 0)
236 goto out;
238 /* expect 0x9f 0xee */
239 r = ch341_get_status(dev, priv);
241 out: kfree(buffer);
242 return r;
245 static int ch341_port_probe(struct usb_serial_port *port)
247 struct ch341_private *priv;
248 int r;
250 priv = kzalloc(sizeof(struct ch341_private), GFP_KERNEL);
251 if (!priv)
252 return -ENOMEM;
254 spin_lock_init(&priv->lock);
255 priv->baud_rate = DEFAULT_BAUD_RATE;
256 priv->line_control = CH341_BIT_RTS | CH341_BIT_DTR;
258 r = ch341_configure(port->serial->dev, priv);
259 if (r < 0)
260 goto error;
262 usb_set_serial_port_data(port, priv);
263 return 0;
265 error: kfree(priv);
266 return r;
269 static int ch341_port_remove(struct usb_serial_port *port)
271 struct ch341_private *priv;
273 priv = usb_get_serial_port_data(port);
274 kfree(priv);
276 return 0;
279 static int ch341_carrier_raised(struct usb_serial_port *port)
281 struct ch341_private *priv = usb_get_serial_port_data(port);
282 if (priv->line_status & CH341_BIT_DCD)
283 return 1;
284 return 0;
287 static void ch341_dtr_rts(struct usb_serial_port *port, int on)
289 struct ch341_private *priv = usb_get_serial_port_data(port);
290 unsigned long flags;
292 /* drop DTR and RTS */
293 spin_lock_irqsave(&priv->lock, flags);
294 if (on)
295 priv->line_control |= CH341_BIT_RTS | CH341_BIT_DTR;
296 else
297 priv->line_control &= ~(CH341_BIT_RTS | CH341_BIT_DTR);
298 spin_unlock_irqrestore(&priv->lock, flags);
299 ch341_set_handshake(port->serial->dev, priv->line_control);
302 static void ch341_close(struct usb_serial_port *port)
304 usb_serial_generic_close(port);
305 usb_kill_urb(port->interrupt_in_urb);
309 /* open this device, set default parameters */
310 static int ch341_open(struct tty_struct *tty, struct usb_serial_port *port)
312 struct usb_serial *serial = port->serial;
313 struct ch341_private *priv = usb_get_serial_port_data(port);
314 int r;
316 r = ch341_configure(serial->dev, priv);
317 if (r)
318 goto out;
320 if (tty)
321 ch341_set_termios(tty, port, NULL);
323 dev_dbg(&port->dev, "%s - submitting interrupt urb\n", __func__);
324 r = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
325 if (r) {
326 dev_err(&port->dev, "%s - failed to submit interrupt urb: %d\n",
327 __func__, r);
328 goto out;
331 r = usb_serial_generic_open(tty, port);
333 out: return r;
336 /* Old_termios contains the original termios settings and
337 * tty->termios contains the new setting to be used.
339 static void ch341_set_termios(struct tty_struct *tty,
340 struct usb_serial_port *port, struct ktermios *old_termios)
342 struct ch341_private *priv = usb_get_serial_port_data(port);
343 unsigned baud_rate;
344 unsigned long flags;
346 baud_rate = tty_get_baud_rate(tty);
348 priv->baud_rate = baud_rate;
350 if (baud_rate) {
351 spin_lock_irqsave(&priv->lock, flags);
352 priv->line_control |= (CH341_BIT_DTR | CH341_BIT_RTS);
353 spin_unlock_irqrestore(&priv->lock, flags);
354 ch341_set_baudrate(port->serial->dev, priv);
355 } else {
356 spin_lock_irqsave(&priv->lock, flags);
357 priv->line_control &= ~(CH341_BIT_DTR | CH341_BIT_RTS);
358 spin_unlock_irqrestore(&priv->lock, flags);
361 ch341_set_handshake(port->serial->dev, priv->line_control);
363 /* Unimplemented:
364 * (cflag & CSIZE) : data bits [5, 8]
365 * (cflag & PARENB) : parity {NONE, EVEN, ODD}
366 * (cflag & CSTOPB) : stop bits [1, 2]
370 static void ch341_break_ctl(struct tty_struct *tty, int break_state)
372 const uint16_t ch341_break_reg =
373 CH341_REG_BREAK1 | ((uint16_t) CH341_REG_BREAK2 << 8);
374 struct usb_serial_port *port = tty->driver_data;
375 int r;
376 uint16_t reg_contents;
377 uint8_t *break_reg;
379 break_reg = kmalloc(2, GFP_KERNEL);
380 if (!break_reg)
381 return;
383 r = ch341_control_in(port->serial->dev, CH341_REQ_READ_REG,
384 ch341_break_reg, 0, break_reg, 2);
385 if (r < 0) {
386 dev_err(&port->dev, "%s - USB control read error (%d)\n",
387 __func__, r);
388 goto out;
390 dev_dbg(&port->dev, "%s - initial ch341 break register contents - reg1: %x, reg2: %x\n",
391 __func__, break_reg[0], break_reg[1]);
392 if (break_state != 0) {
393 dev_dbg(&port->dev, "%s - Enter break state requested\n", __func__);
394 break_reg[0] &= ~CH341_NBREAK_BITS_REG1;
395 break_reg[1] &= ~CH341_NBREAK_BITS_REG2;
396 } else {
397 dev_dbg(&port->dev, "%s - Leave break state requested\n", __func__);
398 break_reg[0] |= CH341_NBREAK_BITS_REG1;
399 break_reg[1] |= CH341_NBREAK_BITS_REG2;
401 dev_dbg(&port->dev, "%s - New ch341 break register contents - reg1: %x, reg2: %x\n",
402 __func__, break_reg[0], break_reg[1]);
403 reg_contents = get_unaligned_le16(break_reg);
404 r = ch341_control_out(port->serial->dev, CH341_REQ_WRITE_REG,
405 ch341_break_reg, reg_contents);
406 if (r < 0)
407 dev_err(&port->dev, "%s - USB control write error (%d)\n",
408 __func__, r);
409 out:
410 kfree(break_reg);
413 static int ch341_tiocmset(struct tty_struct *tty,
414 unsigned int set, unsigned int clear)
416 struct usb_serial_port *port = tty->driver_data;
417 struct ch341_private *priv = usb_get_serial_port_data(port);
418 unsigned long flags;
419 u8 control;
421 spin_lock_irqsave(&priv->lock, flags);
422 if (set & TIOCM_RTS)
423 priv->line_control |= CH341_BIT_RTS;
424 if (set & TIOCM_DTR)
425 priv->line_control |= CH341_BIT_DTR;
426 if (clear & TIOCM_RTS)
427 priv->line_control &= ~CH341_BIT_RTS;
428 if (clear & TIOCM_DTR)
429 priv->line_control &= ~CH341_BIT_DTR;
430 control = priv->line_control;
431 spin_unlock_irqrestore(&priv->lock, flags);
433 return ch341_set_handshake(port->serial->dev, control);
436 static void ch341_update_line_status(struct usb_serial_port *port,
437 unsigned char *data, size_t len)
439 struct ch341_private *priv = usb_get_serial_port_data(port);
440 struct tty_struct *tty;
441 unsigned long flags;
442 u8 status;
443 u8 delta;
445 if (len < 4)
446 return;
448 status = ~data[2] & CH341_BITS_MODEM_STAT;
450 spin_lock_irqsave(&priv->lock, flags);
451 delta = status ^ priv->line_status;
452 priv->line_status = status;
453 spin_unlock_irqrestore(&priv->lock, flags);
455 if (data[1] & CH341_MULT_STAT)
456 dev_dbg(&port->dev, "%s - multiple status change\n", __func__);
458 if (!delta)
459 return;
461 if (delta & CH341_BIT_CTS)
462 port->icount.cts++;
463 if (delta & CH341_BIT_DSR)
464 port->icount.dsr++;
465 if (delta & CH341_BIT_RI)
466 port->icount.rng++;
467 if (delta & CH341_BIT_DCD) {
468 port->icount.dcd++;
469 tty = tty_port_tty_get(&port->port);
470 if (tty) {
471 usb_serial_handle_dcd_change(port, tty,
472 status & CH341_BIT_DCD);
473 tty_kref_put(tty);
477 wake_up_interruptible(&port->port.delta_msr_wait);
480 static void ch341_read_int_callback(struct urb *urb)
482 struct usb_serial_port *port = urb->context;
483 unsigned char *data = urb->transfer_buffer;
484 unsigned int len = urb->actual_length;
485 int status;
487 switch (urb->status) {
488 case 0:
489 /* success */
490 break;
491 case -ECONNRESET:
492 case -ENOENT:
493 case -ESHUTDOWN:
494 /* this urb is terminated, clean up */
495 dev_dbg(&urb->dev->dev, "%s - urb shutting down: %d\n",
496 __func__, urb->status);
497 return;
498 default:
499 dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n",
500 __func__, urb->status);
501 goto exit;
504 usb_serial_debug_data(&port->dev, __func__, len, data);
505 ch341_update_line_status(port, data, len);
506 exit:
507 status = usb_submit_urb(urb, GFP_ATOMIC);
508 if (status) {
509 dev_err(&urb->dev->dev, "%s - usb_submit_urb failed: %d\n",
510 __func__, status);
514 static int ch341_tiocmget(struct tty_struct *tty)
516 struct usb_serial_port *port = tty->driver_data;
517 struct ch341_private *priv = usb_get_serial_port_data(port);
518 unsigned long flags;
519 u8 mcr;
520 u8 status;
521 unsigned int result;
523 spin_lock_irqsave(&priv->lock, flags);
524 mcr = priv->line_control;
525 status = priv->line_status;
526 spin_unlock_irqrestore(&priv->lock, flags);
528 result = ((mcr & CH341_BIT_DTR) ? TIOCM_DTR : 0)
529 | ((mcr & CH341_BIT_RTS) ? TIOCM_RTS : 0)
530 | ((status & CH341_BIT_CTS) ? TIOCM_CTS : 0)
531 | ((status & CH341_BIT_DSR) ? TIOCM_DSR : 0)
532 | ((status & CH341_BIT_RI) ? TIOCM_RI : 0)
533 | ((status & CH341_BIT_DCD) ? TIOCM_CD : 0);
535 dev_dbg(&port->dev, "%s - result = %x\n", __func__, result);
537 return result;
540 static int ch341_reset_resume(struct usb_serial *serial)
542 struct ch341_private *priv;
544 priv = usb_get_serial_port_data(serial->port[0]);
546 /* reconfigure ch341 serial port after bus-reset */
547 ch341_configure(serial->dev, priv);
549 return 0;
552 static struct usb_serial_driver ch341_device = {
553 .driver = {
554 .owner = THIS_MODULE,
555 .name = "ch341-uart",
557 .id_table = id_table,
558 .num_ports = 1,
559 .open = ch341_open,
560 .dtr_rts = ch341_dtr_rts,
561 .carrier_raised = ch341_carrier_raised,
562 .close = ch341_close,
563 .set_termios = ch341_set_termios,
564 .break_ctl = ch341_break_ctl,
565 .tiocmget = ch341_tiocmget,
566 .tiocmset = ch341_tiocmset,
567 .tiocmiwait = usb_serial_generic_tiocmiwait,
568 .read_int_callback = ch341_read_int_callback,
569 .port_probe = ch341_port_probe,
570 .port_remove = ch341_port_remove,
571 .reset_resume = ch341_reset_resume,
574 static struct usb_serial_driver * const serial_drivers[] = {
575 &ch341_device, NULL
578 module_usb_serial_driver(serial_drivers, id_table);
580 MODULE_LICENSE("GPL");