i386/linux-2.3.21/drivers/net/3c503.h

   1 /* Definitions for the 3Com 3c503 Etherlink 2. */
   2 /* This file is distributed under the GPL.
   3    Many of these names and comments are directly from the Crynwr packet
   4    drivers, which are released under the GPL. */
   5
   6 #define EL2H (dev->base_addr + 0x400)
   7 #define EL2L (dev->base_addr)
   8
   9 /* Vendor unique hardware addr. prefix. 3Com has 2 because they ran
  10    out of available addresses on the first one... */
  11
  12 #define OLD_3COM_ID     0x02608c
  13 #define NEW_3COM_ID     0x0020af
  14
  15 /* Shared memory management parameters. NB: The 8 bit cards have only
  16    one bank (MB1) which serves both Tx and Rx packet space. The 16bit
  17    cards have 2 banks, MB0 for Tx packets, and MB1 for Rx packets.
  18    You choose which bank appears in the sh. mem window with EGACFR_MBSn */
  19
  20 #define EL2_MB0_START_PG        (0x00)  /* EL2/16 Tx packets go in bank 0 */
  21 #define EL2_MB1_START_PG        (0x20)  /* First page of bank 1 */
  22 #define EL2_MB1_STOP_PG         (0x40)  /* Last page +1 of bank 1 */
  23
  24 /* 3Com 3c503 ASIC registers */
  25 #define E33G_STARTPG    (EL2H+0)        /* Start page, matching EN0_STARTPG */
  26 #define E33G_STOPPG     (EL2H+1)        /* Stop page, must match EN0_STOPPG */
  27 #define E33G_DRQCNT     (EL2H+2)        /* DMA burst count */
  28 #define E33G_IOBASE     (EL2H+3)        /* Read of I/O base jumpers. */
  29         /* (non-useful, but it also appears at the end of EPROM space) */
  30 #define E33G_ROMBASE    (EL2H+4)        /* Read of memory base jumpers. */
  31 #define E33G_GACFR      (EL2H+5)        /* Config/setup bits for the ASIC GA */
  32 #define E33G_CNTRL      (EL2H+6)        /* Board's main control register */
  33 #define E33G_STATUS     (EL2H+7)        /* Status on completions. */
  34 #define E33G_IDCFR      (EL2H+8)        /* Interrupt/DMA config register */
  35                                 /* (Which IRQ to assert, DMA chan to use) */
  36 #define E33G_DMAAH      (EL2H+9)        /* High byte of DMA address reg */
  37 #define E33G_DMAAL      (EL2H+10)       /* Low byte of DMA address reg */
  38 /* "Vector pointer" - if this address matches a read, the EPROM (rather than
  39    shared RAM) is mapped into memory space. */
  40 #define E33G_VP2        (EL2H+11)
  41 #define E33G_VP1        (EL2H+12)
  42 #define E33G_VP0        (EL2H+13)
  43 #define E33G_FIFOH      (EL2H+14)       /* FIFO for programmed I/O moves */
  44 #define E33G_FIFOL      (EL2H+15)       /* ... low byte of above. */
  45
  46 /* Bits in E33G_CNTRL register: */
  47
  48 #define ECNTRL_RESET    (0x01)  /* Software reset of the ASIC and 8390 */
  49 #define ECNTRL_THIN     (0x02)  /* Onboard xcvr enable, AUI disable */
  50 #define ECNTRL_AUI      (0x00)  /* Onboard xcvr disable, AUI enable */
  51 #define ECNTRL_SAPROM   (0x04)  /* Map the station address prom */
  52 #define ECNTRL_DBLBFR   (0x20)  /* FIFO configuration bit */
  53 #define ECNTRL_OUTPUT   (0x40)  /* PC-to-3C503 direction if 1 */
  54 #define ECNTRL_INPUT    (0x00)  /* 3C503-to-PC direction if 0 */
  55 #define ECNTRL_START    (0x80)  /* Start the DMA logic */
  56
  57 /* Bits in E33G_STATUS register: */
  58
  59 #define ESTAT_DPRDY     (0x80)  /* Data port (of FIFO) ready */
  60 #define ESTAT_UFLW      (0x40)  /* Tried to read FIFO when it was empty */
  61 #define ESTAT_OFLW      (0x20)  /* Tried to write FIFO when it was full */
  62 #define ESTAT_DTC       (0x10)  /* Terminal Count from PC bus DMA logic */
  63 #define ESTAT_DIP       (0x08)  /* DMA In Progress */
  64
  65 /* Bits in E33G_GACFR register: */
  66
  67 #define EGACFR_NIM      (0x80)  /* NIC interrupt mask */
  68 #define EGACFR_TCM      (0x40)  /* DMA term. count interrupt mask */
  69 #define EGACFR_RSEL     (0x08)  /* Map a bank of card mem into system mem */
  70 #define EGACFR_MBS2     (0x04)  /* Memory bank select, bit 2. */
  71 #define EGACFR_MBS1     (0x02)  /* Memory bank select, bit 1. */
  72 #define EGACFR_MBS0     (0x01)  /* Memory bank select, bit 0. */
  73
  74 #define EGACFR_NORM     (0x49)  /* TCM | RSEL | MBS0 */
  75 #define EGACFR_IRQOFF   (0xc9)  /* TCM | RSEL | MBS0 | NIM */
  76
  77 /*
  78         MBS2    MBS1    MBS0    Sh. mem windows card mem at:
  79         ----    ----    ----    -----------------------------
  80         0       0       0       0x0000 -- bank 0
  81         0       0       1       0x2000 -- bank 1 (only choice for 8bit card)
  82         0       1       0       0x4000 -- bank 2, not used
  83         0       1       1       0x6000 -- bank 3, not used
  84
  85 There was going to be a 32k card that used bank 2 and 3, but it
  86 never got produced.
  87
  88 */
  89
  90
  91 /* End of 3C503 parameter definitions */