include/asm-powerpc/uninorth.h

   1 /*
   2  * uninorth.h: definitions for using the "UniNorth" host bridge chip
   3  *             from Apple. This chip is used on "Core99" machines
   4  *             This also includes U2 used on more recent MacRISC2/3
   5  *             machines and U3 (G5)
   6  *
   7  */
   8 #ifdef __KERNEL__
   9 #ifndef __ASM_UNINORTH_H__
  10 #define __ASM_UNINORTH_H__
  11
  12 /*
  13  * Uni-N and U3 config space reg. definitions
  14  *
  15  * (Little endian)
  16  */
  17
  18 /* Address ranges selection. This one should work with Bandit too */
  19 /* Not U3 */
  20 #define UNI_N_ADDR_SELECT               0x48
  21 #define UNI_N_ADDR_COARSE_MASK          0xffff0000      /* 256Mb regions at *0000000 */
  22 #define UNI_N_ADDR_FINE_MASK            0x0000ffff      /*  16Mb regions at f*000000 */
  23
  24 /* AGP registers */
  25 /* Not U3 */
  26 #define UNI_N_CFG_GART_BASE             0x8c
  27 #define UNI_N_CFG_AGP_BASE              0x90
  28 #define UNI_N_CFG_GART_CTRL             0x94
  29 #define UNI_N_CFG_INTERNAL_STATUS       0x98
  30 #define UNI_N_CFG_GART_DUMMY_PAGE       0xa4
  31
  32 /* UNI_N_CFG_GART_CTRL bits definitions */
  33 #define UNI_N_CFG_GART_INVAL            0x00000001
  34 #define UNI_N_CFG_GART_ENABLE           0x00000100
  35 #define UNI_N_CFG_GART_2xRESET          0x00010000
  36 #define UNI_N_CFG_GART_DISSBADET        0x00020000
  37 /* The following seems to only be used only on U3 <j.glisse@gmail.com> */
  38 #define U3_N_CFG_GART_SYNCMODE          0x00040000
  39 #define U3_N_CFG_GART_PERFRD            0x00080000
  40 #define U3_N_CFG_GART_B2BGNT            0x00200000
  41 #define U3_N_CFG_GART_FASTDDR           0x00400000
  42
  43 /* My understanding of UniNorth AGP as of UniNorth rev 1.0x,
  44  * revision 1.5 (x4 AGP) may need further changes.
  45  *
  46  * AGP_BASE register contains the base address of the AGP aperture on
  47  * the AGP bus. It doesn't seem to be visible to the CPU as of UniNorth 1.x,
  48  * even if decoding of this address range is enabled in the address select
  49  * register. Apparently, the only supported bases are 256Mb multiples
  50  * (high 4 bits of that register).
  51  *
  52  * GART_BASE register appear to contain the physical address of the GART
  53  * in system memory in the high address bits (page aligned), and the
  54  * GART size in the low order bits (number of GART pages)
  55  *
  56  * The GART format itself is one 32bits word per physical memory page.
  57  * This word contains, in little-endian format (!!!), the physical address
  58  * of the page in the high bits, and what appears to be an "enable" bit
  59  * in the LSB bit (0) that must be set to 1 when the entry is valid.
  60  *
  61  * Obviously, the GART is not cache coherent and so any change to it
  62  * must be flushed to memory (or maybe just make the GART space non
  63  * cachable). AGP memory itself doens't seem to be cache coherent neither.
  64  *
  65  * In order to invalidate the GART (which is probably necessary to inval
  66  * the bridge internal TLBs), the following sequence has to be written,
  67  * in order, to the GART_CTRL register:
  68  *
  69  *   UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL
  70  *   UNI_N_CFG_GART_ENABLE
  71  *   UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_2xRESET
  72  *   UNI_N_CFG_GART_ENABLE
  73  *
  74  * As far as AGP "features" are concerned, it looks like fast write may
  75  * not be supported but this has to be confirmed.
  76  *
  77  * Turning on AGP seem to require a double invalidate operation, one before
  78  * setting the AGP command register, on after.
  79  *
  80  * Turning off AGP seems to require the following sequence: first wait
  81  * for the AGP to be idle by reading the internal status register, then
  82  * write in that order to the GART_CTRL register:
  83  *
  84  *   UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL
  85  *   0
  86  *   UNI_N_CFG_GART_2xRESET
  87  *   0
  88  */
  89
  90 /*
  91  * Uni-N memory mapped reg. definitions
  92  *
  93  * Those registers are Big-Endian !!
  94  *
  95  * Their meaning come from either Darwin and/or from experiments I made with
  96  * the bootrom, I'm not sure about their exact meaning yet
  97  *
  98  */
  99
 100 /* Version of the UniNorth chip */
 101 #define UNI_N_VERSION                   0x0000          /* Known versions: 3,7 and 8 */
 102
 103 #define UNI_N_VERSION_107               0x0003          /* 1.0.7 */
 104 #define UNI_N_VERSION_10A               0x0007          /* 1.0.10 */
 105 #define UNI_N_VERSION_150               0x0011          /* 1.5 */
 106 #define UNI_N_VERSION_200               0x0024          /* 2.0 */
 107 #define UNI_N_VERSION_PANGEA            0x00C0          /* Integrated U1 + K */
 108 #define UNI_N_VERSION_INTREPID          0x00D2          /* Integrated U2 + K */
 109 #define UNI_N_VERSION_300               0x0030          /* 3.0 (U3 on G5) */
 110
 111 /* This register is used to enable/disable various clocks */
 112 #define UNI_N_CLOCK_CNTL                0x0020
 113 #define UNI_N_CLOCK_CNTL_PCI            0x00000001      /* PCI2 clock control */
 114 #define UNI_N_CLOCK_CNTL_GMAC           0x00000002      /* GMAC clock control */
 115 #define UNI_N_CLOCK_CNTL_FW             0x00000004      /* FireWire clock control */
 116 #define UNI_N_CLOCK_CNTL_ATA100         0x00000010      /* ATA-100 clock control (U2) */
 117
 118 /* Power Management control */
 119 #define UNI_N_POWER_MGT                 0x0030
 120 #define UNI_N_POWER_MGT_NORMAL          0x00
 121 #define UNI_N_POWER_MGT_IDLE2           0x01
 122 #define UNI_N_POWER_MGT_SLEEP           0x02
 123
 124 /* This register is configured by Darwin depending on the UniN
 125  * revision
 126  */
 127 #define UNI_N_ARB_CTRL                  0x0040
 128 #define UNI_N_ARB_CTRL_QACK_DELAY_SHIFT 15
 129 #define UNI_N_ARB_CTRL_QACK_DELAY_MASK  0x0e1f8000
 130 #define UNI_N_ARB_CTRL_QACK_DELAY       0x30
 131 #define UNI_N_ARB_CTRL_QACK_DELAY105    0x00
 132
 133 /* This one _might_ return the CPU number of the CPU reading it;
 134  * the bootROM decides whether to boot or to sleep/spinloop depending
 135  * on this register beeing 0 or not
 136  */
 137 #define UNI_N_CPU_NUMBER                0x0050
 138
 139 /* This register appear to be read by the bootROM to decide what
 140  *  to do on a non-recoverable reset (powerup or wakeup)
 141  */
 142 #define UNI_N_HWINIT_STATE              0x0070
 143 #define UNI_N_HWINIT_STATE_SLEEPING     0x01
 144 #define UNI_N_HWINIT_STATE_RUNNING      0x02
 145 /* This last bit appear to be used by the bootROM to know the second
 146  * CPU has started and will enter it's sleep loop with IP=0
 147  */
 148 #define UNI_N_HWINIT_STATE_CPU1_FLAG    0x10000000
 149
 150 /* This register controls AACK delay, which is set when 2004 iBook/PowerBook
 151  * is in low speed mode.
 152  */
 153 #define UNI_N_AACK_DELAY                0x0100
 154 #define UNI_N_AACK_DELAY_ENABLE         0x00000001
 155
 156 /* Clock status for Intrepid */
 157 #define UNI_N_CLOCK_STOP_STATUS0        0x0150
 158 #define UNI_N_CLOCK_STOPPED_EXTAGP      0x00200000
 159 #define UNI_N_CLOCK_STOPPED_AGPDEL      0x00100000
 160 #define UNI_N_CLOCK_STOPPED_I2S0_45_49  0x00080000
 161 #define UNI_N_CLOCK_STOPPED_I2S0_18     0x00040000
 162 #define UNI_N_CLOCK_STOPPED_I2S1_45_49  0x00020000
 163 #define UNI_N_CLOCK_STOPPED_I2S1_18     0x00010000
 164 #define UNI_N_CLOCK_STOPPED_TIMER       0x00008000
 165 #define UNI_N_CLOCK_STOPPED_SCC_RTCLK18 0x00004000
 166 #define UNI_N_CLOCK_STOPPED_SCC_RTCLK32 0x00002000
 167 #define UNI_N_CLOCK_STOPPED_SCC_VIA32   0x00001000
 168 #define UNI_N_CLOCK_STOPPED_SCC_SLOT0   0x00000800
 169 #define UNI_N_CLOCK_STOPPED_SCC_SLOT1   0x00000400
 170 #define UNI_N_CLOCK_STOPPED_SCC_SLOT2   0x00000200
 171 #define UNI_N_CLOCK_STOPPED_PCI_FBCLKO  0x00000100
 172 #define UNI_N_CLOCK_STOPPED_VEO0        0x00000080
 173 #define UNI_N_CLOCK_STOPPED_VEO1        0x00000040
 174 #define UNI_N_CLOCK_STOPPED_USB0        0x00000020
 175 #define UNI_N_CLOCK_STOPPED_USB1        0x00000010
 176 #define UNI_N_CLOCK_STOPPED_USB2        0x00000008
 177 #define UNI_N_CLOCK_STOPPED_32          0x00000004
 178 #define UNI_N_CLOCK_STOPPED_45          0x00000002
 179 #define UNI_N_CLOCK_STOPPED_49          0x00000001
 180
 181 #define UNI_N_CLOCK_STOP_STATUS1        0x0160
 182 #define UNI_N_CLOCK_STOPPED_PLL4REF     0x00080000
 183 #define UNI_N_CLOCK_STOPPED_CPUDEL      0x00040000
 184 #define UNI_N_CLOCK_STOPPED_CPU         0x00020000
 185 #define UNI_N_CLOCK_STOPPED_BUF_REFCKO  0x00010000
 186 #define UNI_N_CLOCK_STOPPED_PCI2        0x00008000
 187 #define UNI_N_CLOCK_STOPPED_FW          0x00004000
 188 #define UNI_N_CLOCK_STOPPED_GB          0x00002000
 189 #define UNI_N_CLOCK_STOPPED_ATA66       0x00001000
 190 #define UNI_N_CLOCK_STOPPED_ATA100      0x00000800
 191 #define UNI_N_CLOCK_STOPPED_MAX         0x00000400
 192 #define UNI_N_CLOCK_STOPPED_PCI1        0x00000200
 193 #define UNI_N_CLOCK_STOPPED_KLPCI       0x00000100
 194 #define UNI_N_CLOCK_STOPPED_USB0PCI     0x00000080
 195 #define UNI_N_CLOCK_STOPPED_USB1PCI     0x00000040
 196 #define UNI_N_CLOCK_STOPPED_USB2PCI     0x00000020
 197 #define UNI_N_CLOCK_STOPPED_7PCI1       0x00000008
 198 #define UNI_N_CLOCK_STOPPED_AGP         0x00000004
 199 #define UNI_N_CLOCK_STOPPED_PCI0        0x00000002
 200 #define UNI_N_CLOCK_STOPPED_18          0x00000001
 201
 202 /* Intrepid registe to OF do-platform-clockspreading */
 203 #define UNI_N_CLOCK_SPREADING           0x190
 204
 205 /* Uninorth 1.5 rev. has additional perf. monitor registers at 0xf00-0xf50 */
 206
 207
 208 /*
 209  * U3 specific registers
 210  */
 211
 212
 213 /* U3 Toggle */
 214 #define U3_TOGGLE_REG                   0x00e0
 215 #define U3_PMC_START_STOP               0x0001
 216 #define U3_MPIC_RESET                   0x0002
 217 #define U3_MPIC_OUTPUT_ENABLE           0x0004
 218
 219 /* U3 API PHY Config 1 */
 220 #define U3_API_PHY_CONFIG_1             0x23030
 221
 222 /* U3 HyperTransport registers */
 223 #define U3_HT_CONFIG_BASE               0x70000
 224 #define U3_HT_LINK_COMMAND              0x100
 225 #define U3_HT_LINK_CONFIG               0x110
 226 #define U3_HT_LINK_FREQ                 0x120
 227
 228 #endif /* __ASM_UNINORTH_H__ */
 229 #endif /* __KERNEL__ */