x86: use _ASM_EXTABLE macro in include/asm-x86/uaccess_64.h

[wrt350n-kernel.git] / drivers / mtd / nand / rtc_from4.c

/*
 *  drivers/mtd/nand/rtc_from4.c
 *
 *  Copyright (C) 2004  Red Hat, Inc.
 *
 *  Derived from drivers/mtd/nand/spia.c
 *       Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com)
 *
 * $Id: rtc_from4.c,v 1.10 2005/11/07 11:14:31 gleixner Exp $
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * Overview:
 *   This is a device driver for the AG-AND flash device found on the
 *   Renesas Technology Corp. Flash ROM 4-slot interface board (FROM_BOARD4),
 *   which utilizes the Renesas HN29V1G91T-30 part.
 *   This chip is a 1 GBibit (128MiB x 8 bits) AG-AND flash device.
 */

#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/rslib.h>
#include <linux/bitrev.h>
#include <linux/module.h>
#include <linux/mtd/compatmac.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <asm/io.h>

/*
 * MTD structure for Renesas board
 */
static struct mtd_info *rtc_from4_mtd = NULL;

#define RTC_FROM4_MAX_CHIPS     2

/* HS77x9 processor register defines */
#define SH77X9_BCR1     ((volatile unsigned short *)(0xFFFFFF60))
#define SH77X9_BCR2     ((volatile unsigned short *)(0xFFFFFF62))
#define SH77X9_WCR1     ((volatile unsigned short *)(0xFFFFFF64))
#define SH77X9_WCR2     ((volatile unsigned short *)(0xFFFFFF66))
#define SH77X9_MCR      ((volatile unsigned short *)(0xFFFFFF68))
#define SH77X9_PCR      ((volatile unsigned short *)(0xFFFFFF6C))
#define SH77X9_FRQCR    ((volatile unsigned short *)(0xFFFFFF80))

/*
 * Values specific to the Renesas Technology Corp. FROM_BOARD4 (used with HS77x9 processor)
 */
/* Address where flash is mapped */
#define RTC_FROM4_FIO_BASE      0x14000000

/* CLE and ALE are tied to address lines 5 & 4, respectively */
#define RTC_FROM4_CLE           (1 << 5)
#define RTC_FROM4_ALE           (1 << 4)

/* address lines A24-A22 used for chip selection */
#define RTC_FROM4_NAND_ADDR_SLOT3       (0x00800000)
#define RTC_FROM4_NAND_ADDR_SLOT4       (0x00C00000)
#define RTC_FROM4_NAND_ADDR_FPGA        (0x01000000)
/* mask address lines A24-A22 used for chip selection */
#define RTC_FROM4_NAND_ADDR_MASK        (RTC_FROM4_NAND_ADDR_SLOT3 | RTC_FROM4_NAND_ADDR_SLOT4 | RTC_FROM4_NAND_ADDR_FPGA)

/* FPGA status register for checking device ready (bit zero) */
#define RTC_FROM4_FPGA_SR               (RTC_FROM4_NAND_ADDR_FPGA | 0x00000002)
#define RTC_FROM4_DEVICE_READY          0x0001

/* FPGA Reed-Solomon ECC Control register */

#define RTC_FROM4_RS_ECC_CTL            (RTC_FROM4_NAND_ADDR_FPGA | 0x00000050)
#define RTC_FROM4_RS_ECC_CTL_CLR        (1 << 7)
#define RTC_FROM4_RS_ECC_CTL_GEN        (1 << 6)
#define RTC_FROM4_RS_ECC_CTL_FD_E       (1 << 5)

/* FPGA Reed-Solomon ECC code base */
#define RTC_FROM4_RS_ECC                (RTC_FROM4_NAND_ADDR_FPGA | 0x00000060)
#define RTC_FROM4_RS_ECCN               (RTC_FROM4_NAND_ADDR_FPGA | 0x00000080)

/* FPGA Reed-Solomon ECC check register */
#define RTC_FROM4_RS_ECC_CHK            (RTC_FROM4_NAND_ADDR_FPGA | 0x00000070)
#define RTC_FROM4_RS_ECC_CHK_ERROR      (1 << 7)

#define ERR_STAT_ECC_AVAILABLE          0x20

/* Undefine for software ECC */
#define RTC_FROM4_HWECC 1

/* Define as 1 for no virtual erase blocks (in JFFS2) */
#define RTC_FROM4_NO_VIRTBLOCKS 0

/*
 * Module stuff
 */
static void __iomem *rtc_from4_fio_base = (void *)P2SEGADDR(RTC_FROM4_FIO_BASE);

static const struct mtd_partition partition_info[] = {
        {
         .name = "Renesas flash partition 1",
         .offset = 0,
         .size = MTDPART_SIZ_FULL},
};

#define NUM_PARTITIONS 1

/*
 *      hardware specific flash bbt decriptors
 *      Note: this is to allow debugging by disabling
 *              NAND_BBT_CREATE and/or NAND_BBT_WRITE
 *
 */
static uint8_t bbt_pattern[] = { 'B', 'b', 't', '0' };
static uint8_t mirror_pattern[] = { '1', 't', 'b', 'B' };

static struct nand_bbt_descr rtc_from4_bbt_main_descr = {
        .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
                | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
        .offs = 40,
        .len = 4,
        .veroffs = 44,
        .maxblocks = 4,
        .pattern = bbt_pattern
};

static struct nand_bbt_descr rtc_from4_bbt_mirror_descr = {
        .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
                | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP,
        .offs = 40,
        .len = 4,
        .veroffs = 44,
        .maxblocks = 4,
        .pattern = mirror_pattern
};

#ifdef RTC_FROM4_HWECC

/* the Reed Solomon control structure */
static struct rs_control *rs_decoder;

/*
 *      hardware specific Out Of Band information
 */
static struct nand_ecclayout rtc_from4_nand_oobinfo = {
        .eccbytes = 32,
        .eccpos = {
                   0, 1, 2, 3, 4, 5, 6, 7,
                   8, 9, 10, 11, 12, 13, 14, 15,
                   16, 17, 18, 19, 20, 21, 22, 23,
                   24, 25, 26, 27, 28, 29, 30, 31},
        .oobfree = {{32, 32}}
};

#endif

/*
 * rtc_from4_hwcontrol - hardware specific access to control-lines
 * @mtd:        MTD device structure
 * @cmd:        hardware control command
 *
 * Address lines (A5 and A4) are used to control Command and Address Latch
 * Enable on this board, so set the read/write address appropriately.
 *
 * Chip Enable is also controlled by the Chip Select (CS5) and
 * Address lines (A24-A22), so no action is required here.
 *
 */
static void rtc_from4_hwcontrol(struct mtd_info *mtd, int cmd,
                                unsigned int ctrl)
{
        struct nand_chip *chip = (mtd->priv);

        if (cmd == NAND_CMD_NONE)
                return;

        if (ctrl & NAND_CLE)
                writeb(cmd, chip->IO_ADDR_W | RTC_FROM4_CLE);
        else
                writeb(cmd, chip->IO_ADDR_W | RTC_FROM4_ALE);
}

/*
 * rtc_from4_nand_select_chip - hardware specific chip select
 * @mtd:        MTD device structure
 * @chip:       Chip to select (0 == slot 3, 1 == slot 4)
 *
 * The chip select is based on address lines A24-A22.
 * This driver uses flash slots 3 and 4 (A23-A22).
 *
 */
static void rtc_from4_nand_select_chip(struct mtd_info *mtd, int chip)
{
        struct nand_chip *this = mtd->priv;

        this->IO_ADDR_R = (void __iomem *)((unsigned long)this->IO_ADDR_R & ~RTC_FROM4_NAND_ADDR_MASK);
        this->IO_ADDR_W = (void __iomem *)((unsigned long)this->IO_ADDR_W & ~RTC_FROM4_NAND_ADDR_MASK);

        switch (chip) {

        case 0:         /* select slot 3 chip */
                this->IO_ADDR_R = (void __iomem *)((unsigned long)this->IO_ADDR_R | RTC_FROM4_NAND_ADDR_SLOT3);
                this->IO_ADDR_W = (void __iomem *)((unsigned long)this->IO_ADDR_W | RTC_FROM4_NAND_ADDR_SLOT3);
                break;
        case 1:         /* select slot 4 chip */
                this->IO_ADDR_R = (void __iomem *)((unsigned long)this->IO_ADDR_R | RTC_FROM4_NAND_ADDR_SLOT4);
                this->IO_ADDR_W = (void __iomem *)((unsigned long)this->IO_ADDR_W | RTC_FROM4_NAND_ADDR_SLOT4);
                break;

        }
}

/*
 * rtc_from4_nand_device_ready - hardware specific ready/busy check
 * @mtd:        MTD device structure
 *
 * This board provides the Ready/Busy state in the status register
 * of the FPGA.  Bit zero indicates the RDY(1)/BSY(0) signal.
 *
 */
static int rtc_from4_nand_device_ready(struct mtd_info *mtd)
{
        unsigned short status;

        status = *((volatile unsigned short *)(rtc_from4_fio_base + RTC_FROM4_FPGA_SR));

        return (status & RTC_FROM4_DEVICE_READY);

}

/*
 * deplete - code to perform device recovery in case there was a power loss
 * @mtd:        MTD device structure
 * @chip:       Chip to select (0 == slot 3, 1 == slot 4)
 *
 * If there was a sudden loss of power during an erase operation, a
 * "device recovery" operation must be performed when power is restored
 * to ensure correct operation.  This routine performs the required steps
 * for the requested chip.
 *
 * See page 86 of the data sheet for details.
 *
 */
static void deplete(struct mtd_info *mtd, int chip)
{
        struct nand_chip *this = mtd->priv;

        /* wait until device is ready */
        while (!this->dev_ready(mtd)) ;

        this->select_chip(mtd, chip);

        /* Send the commands for device recovery, phase 1 */
        this->cmdfunc(mtd, NAND_CMD_DEPLETE1, 0x0000, 0x0000);
        this->cmdfunc(mtd, NAND_CMD_DEPLETE2, -1, -1);

        /* Send the commands for device recovery, phase 2 */
        this->cmdfunc(mtd, NAND_CMD_DEPLETE1, 0x0000, 0x0004);
        this->cmdfunc(mtd, NAND_CMD_DEPLETE2, -1, -1);

}

#ifdef RTC_FROM4_HWECC
/*
 * rtc_from4_enable_hwecc - hardware specific hardware ECC enable function
 * @mtd:        MTD device structure
 * @mode:       I/O mode; read or write
 *
 * enable hardware ECC for data read or write
 *
 */
static void rtc_from4_enable_hwecc(struct mtd_info *mtd, int mode)
{
        volatile unsigned short *rs_ecc_ctl = (volatile unsigned short *)(rtc_from4_fio_base + RTC_FROM4_RS_ECC_CTL);
        unsigned short status;

        switch (mode) {
        case NAND_ECC_READ:
                status = RTC_FROM4_RS_ECC_CTL_CLR | RTC_FROM4_RS_ECC_CTL_FD_E;

                *rs_ecc_ctl = status;
                break;

        case NAND_ECC_READSYN:
                status = 0x00;

                *rs_ecc_ctl = status;
                break;

        case NAND_ECC_WRITE:
                status = RTC_FROM4_RS_ECC_CTL_CLR | RTC_FROM4_RS_ECC_CTL_GEN | RTC_FROM4_RS_ECC_CTL_FD_E;

                *rs_ecc_ctl = status;
                break;

        default:
                BUG();
                break;
        }

}

/*
 * rtc_from4_calculate_ecc - hardware specific code to read ECC code
 * @mtd:        MTD device structure
 * @dat:        buffer containing the data to generate ECC codes
 * @ecc_code    ECC codes calculated
 *
 * The ECC code is calculated by the FPGA.  All we have to do is read the values
 * from the FPGA registers.
 *
 * Note: We read from the inverted registers, since data is inverted before
 * the code is calculated. So all 0xff data (blank page) results in all 0xff rs code
 *
 */
static void rtc_from4_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code)
{
        volatile unsigned short *rs_eccn = (volatile unsigned short *)(rtc_from4_fio_base + RTC_FROM4_RS_ECCN);
        unsigned short value;
        int i;

        for (i = 0; i < 8; i++) {
                value = *rs_eccn;
                ecc_code[i] = (unsigned char)value;
                rs_eccn++;
        }
        ecc_code[7] |= 0x0f;    /* set the last four bits (not used) */
}

/*
 * rtc_from4_correct_data - hardware specific code to correct data using ECC code
 * @mtd:        MTD device structure
 * @buf:        buffer containing the data to generate ECC codes
 * @ecc1        ECC codes read
 * @ecc2        ECC codes calculated
 *
 * The FPGA tells us fast, if there's an error or not. If no, we go back happy
 * else we read the ecc results from the fpga and call the rs library to decode
 * and hopefully correct the error.
 *
 */
static int rtc_from4_correct_data(struct mtd_info *mtd, const u_char *buf, u_char *ecc1, u_char *ecc2)
{
        int i, j, res;
        unsigned short status;
        uint16_t par[6], syn[6];
        uint8_t ecc[8];
        volatile unsigned short *rs_ecc;

        status = *((volatile unsigned short *)(rtc_from4_fio_base + RTC_FROM4_RS_ECC_CHK));

        if (!(status & RTC_FROM4_RS_ECC_CHK_ERROR)) {
                return 0;
        }

        /* Read the syndrom pattern from the FPGA and correct the bitorder */
        rs_ecc = (volatile unsigned short *)(rtc_from4_fio_base + RTC_FROM4_RS_ECC);
        for (i = 0; i < 8; i++) {
                ecc[i] = bitrev8(*rs_ecc);
                rs_ecc++;
        }

        /* convert into 6 10bit syndrome fields */
        par[5] = rs_decoder->index_of[(((uint16_t) ecc[0] >> 0) & 0x0ff) | (((uint16_t) ecc[1] << 8) & 0x300)];
        par[4] = rs_decoder->index_of[(((uint16_t) ecc[1] >> 2) & 0x03f) | (((uint16_t) ecc[2] << 6) & 0x3c0)];
        par[3] = rs_decoder->index_of[(((uint16_t) ecc[2] >> 4) & 0x00f) | (((uint16_t) ecc[3] << 4) & 0x3f0)];
        par[2] = rs_decoder->index_of[(((uint16_t) ecc[3] >> 6) & 0x003) | (((uint16_t) ecc[4] << 2) & 0x3fc)];
        par[1] = rs_decoder->index_of[(((uint16_t) ecc[5] >> 0) & 0x0ff) | (((uint16_t) ecc[6] << 8) & 0x300)];
        par[0] = (((uint16_t) ecc[6] >> 2) & 0x03f) | (((uint16_t) ecc[7] << 6) & 0x3c0);

        /* Convert to computable syndrome */
        for (i = 0; i < 6; i++) {
                syn[i] = par[0];
                for (j = 1; j < 6; j++)
                        if (par[j] != rs_decoder->nn)
                                syn[i] ^= rs_decoder->alpha_to[rs_modnn(rs_decoder, par[j] + i * j)];

                /* Convert to index form */
                syn[i] = rs_decoder->index_of[syn[i]];
        }

        /* Let the library code do its magic. */
        res = decode_rs8(rs_decoder, (uint8_t *) buf, par, 512, syn, 0, NULL, 0xff, NULL);
        if (res > 0) {
                DEBUG(MTD_DEBUG_LEVEL0, "rtc_from4_correct_data: " "ECC corrected %d errors on read\n", res);
        }
        return res;
}

/**
 * rtc_from4_errstat - perform additional error status checks
 * @mtd:        MTD device structure
 * @this:       NAND chip structure
 * @state:      state or the operation
 * @status:     status code returned from read status
 * @page:       startpage inside the chip, must be called with (page & this->pagemask)
 *
 * Perform additional error status checks on erase and write failures
 * to determine if errors are correctable.  For this device, correctable
 * 1-bit errors on erase and write are considered acceptable.
 *
 * note: see pages 34..37 of data sheet for details.
 *
 */
static int rtc_from4_errstat(struct mtd_info *mtd, struct nand_chip *this,
                             int state, int status, int page)
{
        int er_stat = 0;
        int rtn, retlen;
        size_t len;
        uint8_t *buf;
        int i;

        this->cmdfunc(mtd, NAND_CMD_STATUS_CLEAR, -1, -1);

        if (state == FL_ERASING) {

                for (i = 0; i < 4; i++) {
                        if (!(status & 1 << (i + 1)))
                                continue;
                        this->cmdfunc(mtd, (NAND_CMD_STATUS_ERROR + i + 1),
                                      -1, -1);
                        rtn = this->read_byte(mtd);
                        this->cmdfunc(mtd, NAND_CMD_STATUS_RESET, -1, -1);

                        /* err_ecc_not_avail */
                        if (!(rtn & ERR_STAT_ECC_AVAILABLE))
                                er_stat |= 1 << (i + 1);
                }

        } else if (state == FL_WRITING) {

                unsigned long corrected = mtd->ecc_stats.corrected;

                /* single bank write logic */
                this->cmdfunc(mtd, NAND_CMD_STATUS_ERROR, -1, -1);
                rtn = this->read_byte(mtd);
                this->cmdfunc(mtd, NAND_CMD_STATUS_RESET, -1, -1);

                if (!(rtn & ERR_STAT_ECC_AVAILABLE)) {
                        /* err_ecc_not_avail */
                        er_stat |= 1 << 1;
                        goto out;
                }

                len = mtd->writesize;
                buf = kmalloc(len, GFP_KERNEL);
                if (!buf) {
                        printk(KERN_ERR "rtc_from4_errstat: Out of memory!\n");
                        er_stat = 1;
                        goto out;
                }

                /* recovery read */
                rtn = nand_do_read(mtd, page, len, &retlen, buf);

                /* if read failed or > 1-bit error corrected */
                if (rtn || (mtd->ecc_stats.corrected - corrected) > 1)
                        er_stat |= 1 << 1;
                kfree(buf);
        }

        rtn = status;
        if (er_stat == 0) {     /* if ECC is available   */
                rtn = (status & ~NAND_STATUS_FAIL);     /*   clear the error bit */
        }

        return rtn;
}
#endif

/*
 * Main initialization routine
 */
static int __init rtc_from4_init(void)
{
        struct nand_chip *this;
        unsigned short bcr1, bcr2, wcr2;
        int i;

        /* Allocate memory for MTD device structure and private data */
        rtc_from4_mtd = kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL);
        if (!rtc_from4_mtd) {
                printk("Unable to allocate Renesas NAND MTD device structure.\n");
                return -ENOMEM;
        }

        /* Get pointer to private data */
        this = (struct nand_chip *)(&rtc_from4_mtd[1]);

        /* Initialize structures */
        memset(rtc_from4_mtd, 0, sizeof(struct mtd_info));
        memset(this, 0, sizeof(struct nand_chip));

        /* Link the private data with the MTD structure */
        rtc_from4_mtd->priv = this;
        rtc_from4_mtd->owner = THIS_MODULE;

        /* set area 5 as PCMCIA mode to clear the spec of tDH(Data hold time;9ns min) */
        bcr1 = *SH77X9_BCR1 & ~0x0002;
        bcr1 |= 0x0002;
        *SH77X9_BCR1 = bcr1;

        /* set */
        bcr2 = *SH77X9_BCR2 & ~0x0c00;
        bcr2 |= 0x0800;
        *SH77X9_BCR2 = bcr2;

        /* set area 5 wait states */
        wcr2 = *SH77X9_WCR2 & ~0x1c00;
        wcr2 |= 0x1c00;
        *SH77X9_WCR2 = wcr2;

        /* Set address of NAND IO lines */
        this->IO_ADDR_R = rtc_from4_fio_base;
        this->IO_ADDR_W = rtc_from4_fio_base;
        /* Set address of hardware control function */
        this->cmd_ctrl = rtc_from4_hwcontrol;
        /* Set address of chip select function */
        this->select_chip = rtc_from4_nand_select_chip;
        /* command delay time (in us) */
        this->chip_delay = 100;
        /* return the status of the Ready/Busy line */
        this->dev_ready = rtc_from4_nand_device_ready;

#ifdef RTC_FROM4_HWECC
        printk(KERN_INFO "rtc_from4_init: using hardware ECC detection.\n");

        this->ecc.mode = NAND_ECC_HW_SYNDROME;
        this->ecc.size = 512;
        this->ecc.bytes = 8;
        /* return the status of extra status and ECC checks */
        this->errstat = rtc_from4_errstat;
        /* set the nand_oobinfo to support FPGA H/W error detection */
        this->ecc.layout = &rtc_from4_nand_oobinfo;
        this->ecc.hwctl = rtc_from4_enable_hwecc;
        this->ecc.calculate = rtc_from4_calculate_ecc;
        this->ecc.correct = rtc_from4_correct_data;
#else
        printk(KERN_INFO "rtc_from4_init: using software ECC detection.\n");

        this->ecc.mode = NAND_ECC_SOFT;
#endif

        /* set the bad block tables to support debugging */
        this->bbt_td = &rtc_from4_bbt_main_descr;
        this->bbt_md = &rtc_from4_bbt_mirror_descr;

        /* Scan to find existence of the device */
        if (nand_scan(rtc_from4_mtd, RTC_FROM4_MAX_CHIPS)) {
                kfree(rtc_from4_mtd);
                return -ENXIO;
        }

        /* Perform 'device recovery' for each chip in case there was a power loss. */
        for (i = 0; i < this->numchips; i++) {
                deplete(rtc_from4_mtd, i);
        }

#if RTC_FROM4_NO_VIRTBLOCKS
        /* use a smaller erase block to minimize wasted space when a block is bad */
        /* note: this uses eight times as much RAM as using the default and makes */
        /*       mounts take four times as long. */
        rtc_from4_mtd->flags |= MTD_NO_VIRTBLOCKS;
#endif

        /* Register the partitions */
        add_mtd_partitions(rtc_from4_mtd, partition_info, NUM_PARTITIONS);

#ifdef RTC_FROM4_HWECC
        /* We could create the decoder on demand, if memory is a concern.
         * This way we have it handy, if an error happens
         *
         * Symbolsize is 10 (bits)
         * Primitve polynomial is x^10+x^3+1
         * first consecutive root is 0
         * primitve element to generate roots = 1
         * generator polinomial degree = 6
         */
        rs_decoder = init_rs(10, 0x409, 0, 1, 6);
        if (!rs_decoder) {
                printk(KERN_ERR "Could not create a RS decoder\n");
                nand_release(rtc_from4_mtd);
                kfree(rtc_from4_mtd);
                return -ENOMEM;
        }
#endif
        /* Return happy */
        return 0;
}

module_init(rtc_from4_init);

/*
 * Clean up routine
 */
static void __exit rtc_from4_cleanup(void)
{
        /* Release resource, unregister partitions */
        nand_release(rtc_from4_mtd);

        /* Free the MTD device structure */
        kfree(rtc_from4_mtd);

#ifdef RTC_FROM4_HWECC
        /* Free the reed solomon resources */
        if (rs_decoder) {
                free_rs(rs_decoder);
        }
#endif
}

module_exit(rtc_from4_cleanup);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("d.marlin <dmarlin@redhat.com");
MODULE_DESCRIPTION("Board-specific glue layer for AG-AND flash on Renesas FROM_BOARD4");