drivers/ata/pata_opti.c

   1 /*
   2  * pata_opti.c  - ATI PATA for new ATA layer
   3  *                        (C) 2005 Red Hat Inc
   4  *                        Alan Cox <alan@redhat.com>
   5  *
   6  * Based on
   7  *  linux/drivers/ide/pci/opti621.c             Version 0.7     Sept 10, 2002
   8  *
   9  *  Copyright (C) 1996-1998  Linus Torvalds & authors (see below)
  10  *
  11  * Authors:
  12  * Jaromir Koutek <miri@punknet.cz>,
  13  * Jan Harkes <jaharkes@cwi.nl>,
  14  * Mark Lord <mlord@pobox.com>
  15  * Some parts of code are from ali14xx.c and from rz1000.c.
  16  *
  17  * Also consulted the FreeBSD prototype driver by Kevin Day to try
  18  * and resolve some confusions. Further documentation can be found in
  19  * Ralf Brown's interrupt list
  20  *
  21  * If you have other variants of the Opti range (Viper/Vendetta) please
  22  * try this driver with those PCI idents and report back. For the later
  23  * chips see the pata_optidma driver
  24  *
  25  */
  26
  27 #include <linux/kernel.h>
  28 #include <linux/module.h>
  29 #include <linux/pci.h>
  30 #include <linux/init.h>
  31 #include <linux/blkdev.h>
  32 #include <linux/delay.h>
  33 #include <scsi/scsi_host.h>
  34 #include <linux/libata.h>
  35
  36 #define DRV_NAME "pata_opti"
  37 #define DRV_VERSION "0.2.9"
  38
  39 enum {
  40         READ_REG        = 0,    /* index of Read cycle timing register */
  41         WRITE_REG       = 1,    /* index of Write cycle timing register */
  42         CNTRL_REG       = 3,    /* index of Control register */
  43         STRAP_REG       = 5,    /* index of Strap register */
  44         MISC_REG        = 6     /* index of Miscellaneous register */
  45 };
  46
  47 /**
  48  *      opti_pre_reset          -       probe begin
  49  *      @link: ATA link
  50  *      @deadline: deadline jiffies for the operation
  51  *
  52  *      Set up cable type and use generic probe init
  53  */
  54
  55 static int opti_pre_reset(struct ata_link *link, unsigned long deadline)
  56 {
  57         struct ata_port *ap = link->ap;
  58         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  59         static const struct pci_bits opti_enable_bits[] = {
  60                 { 0x45, 1, 0x80, 0x00 },
  61                 { 0x40, 1, 0x08, 0x00 }
  62         };
  63
  64         if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no]))
  65                 return -ENOENT;
  66
  67         return ata_std_prereset(link, deadline);
  68 }
  69
  70 /**
  71  *      opti_probe_reset                -       probe reset
  72  *      @ap: ATA port
  73  *
  74  *      Perform the ATA probe and bus reset sequence plus specific handling
  75  *      for this hardware. The Opti needs little handling - we have no UDMA66
  76  *      capability that needs cable detection. All we must do is check the port
  77  *      is enabled.
  78  */
  79
  80 static void opti_error_handler(struct ata_port *ap)
  81 {
  82         ata_bmdma_drive_eh(ap, opti_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
  83 }
  84
  85 /**
  86  *      opti_write_reg          -       control register setup
  87  *      @ap: ATA port
  88  *      @value: value
  89  *      @reg: control register number
  90  *
  91  *      The Opti uses magic 'trapdoor' register accesses to do configuration
  92  *      rather than using PCI space as other controllers do. The double inw
  93  *      on the error register activates configuration mode. We can then write
  94  *      the control register
  95  */
  96
  97 static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
  98 {
  99         void __iomem *regio = ap->ioaddr.cmd_addr;
 100
 101         /* These 3 unlock the control register access */
 102         ioread16(regio + 1);
 103         ioread16(regio + 1);
 104         iowrite8(3, regio + 2);
 105
 106         /* Do the I/O */
 107         iowrite8(val, regio + reg);
 108
 109         /* Relock */
 110         iowrite8(0x83, regio + 2);
 111 }
 112
 113 /**
 114  *      opti_set_piomode        -       set initial PIO mode data
 115  *      @ap: ATA interface
 116  *      @adev: ATA device
 117  *
 118  *      Called to do the PIO mode setup. Timing numbers are taken from
 119  *      the FreeBSD driver then pre computed to keep the code clean. There
 120  *      are two tables depending on the hardware clock speed.
 121  */
 122
 123 static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev)
 124 {
 125         struct ata_device *pair = ata_dev_pair(adev);
 126         int clock;
 127         int pio = adev->pio_mode - XFER_PIO_0;
 128         void __iomem *regio = ap->ioaddr.cmd_addr;
 129         u8 addr;
 130
 131         /* Address table precomputed with prefetch off and a DCLK of 2 */
 132         static const u8 addr_timing[2][5] = {
 133                 { 0x30, 0x20, 0x20, 0x10, 0x10 },
 134                 { 0x20, 0x20, 0x10, 0x10, 0x10 }
 135         };
 136         static const u8 data_rec_timing[2][5] = {
 137                 { 0x6B, 0x56, 0x42, 0x32, 0x31 },
 138                 { 0x58, 0x44, 0x32, 0x22, 0x21 }
 139         };
 140
 141         iowrite8(0xff, regio + 5);
 142         clock = ioread16(regio + 5) & 1;
 143
 144         /*
 145          *      As with many controllers the address setup time is shared
 146          *      and must suit both devices if present.
 147          */
 148
 149         addr = addr_timing[clock][pio];
 150         if (pair) {
 151                 /* Hardware constraint */
 152                 u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0];
 153                 if (pair_addr > addr)
 154                         addr = pair_addr;
 155         }
 156
 157         /* Commence primary programming sequence */
 158         opti_write_reg(ap, adev->devno, MISC_REG);
 159         opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG);
 160         opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG);
 161         opti_write_reg(ap, addr, MISC_REG);
 162
 163         /* Programming sequence complete, override strapping */
 164         opti_write_reg(ap, 0x85, CNTRL_REG);
 165 }
 166
 167 static struct scsi_host_template opti_sht = {
 168         .module                 = THIS_MODULE,
 169         .name                   = DRV_NAME,
 170         .ioctl                  = ata_scsi_ioctl,
 171         .queuecommand           = ata_scsi_queuecmd,
 172         .can_queue              = ATA_DEF_QUEUE,
 173         .this_id                = ATA_SHT_THIS_ID,
 174         .sg_tablesize           = LIBATA_MAX_PRD,
 175         .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
 176         .emulated               = ATA_SHT_EMULATED,
 177         .use_clustering         = ATA_SHT_USE_CLUSTERING,
 178         .proc_name              = DRV_NAME,
 179         .dma_boundary           = ATA_DMA_BOUNDARY,
 180         .slave_configure        = ata_scsi_slave_config,
 181         .slave_destroy          = ata_scsi_slave_destroy,
 182         .bios_param             = ata_std_bios_param,
 183 };
 184
 185 static struct ata_port_operations opti_port_ops = {
 186         .set_piomode    = opti_set_piomode,
 187         .tf_load        = ata_tf_load,
 188         .tf_read        = ata_tf_read,
 189         .check_status   = ata_check_status,
 190         .exec_command   = ata_exec_command,
 191         .dev_select     = ata_std_dev_select,
 192
 193         .freeze         = ata_bmdma_freeze,
 194         .thaw           = ata_bmdma_thaw,
 195         .error_handler  = opti_error_handler,
 196         .post_internal_cmd = ata_bmdma_post_internal_cmd,
 197         .cable_detect   = ata_cable_40wire,
 198
 199         .bmdma_setup    = ata_bmdma_setup,
 200         .bmdma_start    = ata_bmdma_start,
 201         .bmdma_stop     = ata_bmdma_stop,
 202         .bmdma_status   = ata_bmdma_status,
 203
 204         .qc_prep        = ata_qc_prep,
 205         .qc_issue       = ata_qc_issue_prot,
 206
 207         .data_xfer      = ata_data_xfer,
 208
 209         .irq_handler    = ata_interrupt,
 210         .irq_clear      = ata_bmdma_irq_clear,
 211         .irq_on         = ata_irq_on,
 212
 213         .port_start     = ata_sff_port_start,
 214 };
 215
 216 static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 217 {
 218         static const struct ata_port_info info = {
 219                 .sht = &opti_sht,
 220                 .flags = ATA_FLAG_SLAVE_POSS,
 221                 .pio_mask = 0x1f,
 222                 .port_ops = &opti_port_ops
 223         };
 224         const struct ata_port_info *ppi[] = { &info, NULL };
 225         static int printed_version;
 226
 227         if (!printed_version++)
 228                 dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n");
 229
 230         return ata_pci_init_one(dev, ppi);
 231 }
 232
 233 static const struct pci_device_id opti[] = {
 234         { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 },
 235         { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 },
 236
 237         { },
 238 };
 239
 240 static struct pci_driver opti_pci_driver = {
 241         .name           = DRV_NAME,
 242         .id_table       = opti,
 243         .probe          = opti_init_one,
 244         .remove         = ata_pci_remove_one,
 245 #ifdef CONFIG_PM
 246         .suspend        = ata_pci_device_suspend,
 247         .resume         = ata_pci_device_resume,
 248 #endif
 249 };
 250
 251 static int __init opti_init(void)
 252 {
 253         return pci_register_driver(&opti_pci_driver);
 254 }
 255
 256 static void __exit opti_exit(void)
 257 {
 258         pci_unregister_driver(&opti_pci_driver);
 259 }
 260
 261
 262 MODULE_AUTHOR("Alan Cox");
 263 MODULE_DESCRIPTION("low-level driver for Opti 621/621X");
 264 MODULE_LICENSE("GPL");
 265 MODULE_DEVICE_TABLE(pci, opti);
 266 MODULE_VERSION(DRV_VERSION);
 267
 268 module_init(opti_init);
 269 module_exit(opti_exit);