Blackfin serial driver: pending a unique anomaly id, tie the break flood issue to...

[wrt350n-kernel.git] / drivers / net / fec.c

/*
 * Fast Ethernet Controller (FEC) driver for Motorola MPC8xx.
 * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
 *
 * This version of the driver is specific to the FADS implementation,
 * since the board contains control registers external to the processor
 * for the control of the LevelOne LXT970 transceiver.  The MPC860T manual
 * describes connections using the internal parallel port I/O, which
 * is basically all of Port D.
 *
 * Right now, I am very wasteful with the buffers.  I allocate memory
 * pages and then divide them into 2K frame buffers.  This way I know I
 * have buffers large enough to hold one frame within one buffer descriptor.
 * Once I get this working, I will use 64 or 128 byte CPM buffers, which
 * will be much more memory efficient and will easily handle lots of
 * small packets.
 *
 * Much better multiple PHY support by Magnus Damm.
 * Copyright (c) 2000 Ericsson Radio Systems AB.
 *
 * Support for FEC controller of ColdFire processors.
 * Copyright (c) 2001-2005 Greg Ungerer (gerg@snapgear.com)
 *
 * Bug fixes and cleanup by Philippe De Muyter (phdm@macqel.be)
 * Copyright (c) 2004-2006 Macq Electronique SA.
 */

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/ptrace.h>
#include <linux/errno.h>
#include <linux/ioport.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/bitops.h>

#include <asm/irq.h>
#include <asm/uaccess.h>
#include <asm/io.h>
#include <asm/pgtable.h>
#include <asm/cacheflush.h>

#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || \
    defined(CONFIG_M5272) || defined(CONFIG_M528x) || \
    defined(CONFIG_M520x) || defined(CONFIG_M532x)
#include <asm/coldfire.h>
#include <asm/mcfsim.h>
#include "fec.h"
#else
#include <asm/8xx_immap.h>
#include <asm/mpc8xx.h>
#include "commproc.h"
#endif

#if defined(CONFIG_FEC2)
#define FEC_MAX_PORTS   2
#else
#define FEC_MAX_PORTS   1
#endif

/*
 * Define the fixed address of the FEC hardware.
 */
static unsigned int fec_hw[] = {
#if defined(CONFIG_M5272)
        (MCF_MBAR + 0x840),
#elif defined(CONFIG_M527x)
        (MCF_MBAR + 0x1000),
        (MCF_MBAR + 0x1800),
#elif defined(CONFIG_M523x) || defined(CONFIG_M528x)
        (MCF_MBAR + 0x1000),
#elif defined(CONFIG_M520x)
        (MCF_MBAR+0x30000),
#elif defined(CONFIG_M532x)
        (MCF_MBAR+0xfc030000),
#else
        &(((immap_t *)IMAP_ADDR)->im_cpm.cp_fec),
#endif
};

static unsigned char    fec_mac_default[] = {
        0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
};

/*
 * Some hardware gets it MAC address out of local flash memory.
 * if this is non-zero then assume it is the address to get MAC from.
 */
#if defined(CONFIG_NETtel)
#define FEC_FLASHMAC    0xf0006006
#elif defined(CONFIG_GILBARCONAP) || defined(CONFIG_SCALES)
#define FEC_FLASHMAC    0xf0006000
#elif defined(CONFIG_CANCam)
#define FEC_FLASHMAC    0xf0020000
#elif defined (CONFIG_M5272C3)
#define FEC_FLASHMAC    (0xffe04000 + 4)
#elif defined(CONFIG_MOD5272)
#define FEC_FLASHMAC    0xffc0406b
#else
#define FEC_FLASHMAC    0
#endif

/* Forward declarations of some structures to support different PHYs
*/

typedef struct {
        uint mii_data;
        void (*funct)(uint mii_reg, struct net_device *dev);
} phy_cmd_t;

typedef struct {
        uint id;
        char *name;

        const phy_cmd_t *config;
        const phy_cmd_t *startup;
        const phy_cmd_t *ack_int;
        const phy_cmd_t *shutdown;
} phy_info_t;

/* The number of Tx and Rx buffers.  These are allocated from the page
 * pool.  The code may assume these are power of two, so it it best
 * to keep them that size.
 * We don't need to allocate pages for the transmitter.  We just use
 * the skbuffer directly.
 */
#define FEC_ENET_RX_PAGES       8
#define FEC_ENET_RX_FRSIZE      2048
#define FEC_ENET_RX_FRPPG       (PAGE_SIZE / FEC_ENET_RX_FRSIZE)
#define RX_RING_SIZE            (FEC_ENET_RX_FRPPG * FEC_ENET_RX_PAGES)
#define FEC_ENET_TX_FRSIZE      2048
#define FEC_ENET_TX_FRPPG       (PAGE_SIZE / FEC_ENET_TX_FRSIZE)
#define TX_RING_SIZE            16      /* Must be power of two */
#define TX_RING_MOD_MASK        15      /*   for this to work */

#if (((RX_RING_SIZE + TX_RING_SIZE) * 8) > PAGE_SIZE)
#error "FEC: descriptor ring size constants too large"
#endif

/* Interrupt events/masks.
*/
#define FEC_ENET_HBERR  ((uint)0x80000000)      /* Heartbeat error */
#define FEC_ENET_BABR   ((uint)0x40000000)      /* Babbling receiver */
#define FEC_ENET_BABT   ((uint)0x20000000)      /* Babbling transmitter */
#define FEC_ENET_GRA    ((uint)0x10000000)      /* Graceful stop complete */
#define FEC_ENET_TXF    ((uint)0x08000000)      /* Full frame transmitted */
#define FEC_ENET_TXB    ((uint)0x04000000)      /* A buffer was transmitted */
#define FEC_ENET_RXF    ((uint)0x02000000)      /* Full frame received */
#define FEC_ENET_RXB    ((uint)0x01000000)      /* A buffer was received */
#define FEC_ENET_MII    ((uint)0x00800000)      /* MII interrupt */
#define FEC_ENET_EBERR  ((uint)0x00400000)      /* SDMA bus error */

/* The FEC stores dest/src/type, data, and checksum for receive packets.
 */
#define PKT_MAXBUF_SIZE         1518
#define PKT_MINBUF_SIZE         64
#define PKT_MAXBLR_SIZE         1520


/*
 * The 5270/5271/5280/5282/532x RX control register also contains maximum frame
 * size bits. Other FEC hardware does not, so we need to take that into
 * account when setting it.
 */
#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x) || \
    defined(CONFIG_M520x) || defined(CONFIG_M532x)
#define OPT_FRAME_SIZE  (PKT_MAXBUF_SIZE << 16)
#else
#define OPT_FRAME_SIZE  0
#endif

/* The FEC buffer descriptors track the ring buffers.  The rx_bd_base and
 * tx_bd_base always point to the base of the buffer descriptors.  The
 * cur_rx and cur_tx point to the currently available buffer.
 * The dirty_tx tracks the current buffer that is being sent by the
 * controller.  The cur_tx and dirty_tx are equal under both completely
 * empty and completely full conditions.  The empty/ready indicator in
 * the buffer descriptor determines the actual condition.
 */
struct fec_enet_private {
        /* Hardware registers of the FEC device */
        volatile fec_t  *hwp;

        struct net_device *netdev;

        /* The saved address of a sent-in-place packet/buffer, for skfree(). */
        unsigned char *tx_bounce[TX_RING_SIZE];
        struct  sk_buff* tx_skbuff[TX_RING_SIZE];
        ushort  skb_cur;
        ushort  skb_dirty;

        /* CPM dual port RAM relative addresses.
        */
        cbd_t   *rx_bd_base;            /* Address of Rx and Tx buffers. */
        cbd_t   *tx_bd_base;
        cbd_t   *cur_rx, *cur_tx;               /* The next free ring entry */
        cbd_t   *dirty_tx;      /* The ring entries to be free()ed. */
        struct  net_device_stats stats;
        uint    tx_full;
        spinlock_t lock;

        uint    phy_id;
        uint    phy_id_done;
        uint    phy_status;
        uint    phy_speed;
        phy_info_t const        *phy;
        struct work_struct phy_task;

        uint    sequence_done;
        uint    mii_phy_task_queued;

        uint    phy_addr;

        int     index;
        int     opened;
        int     link;
        int     old_link;
        int     full_duplex;
};

static int fec_enet_open(struct net_device *dev);
static int fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev);
static void fec_enet_mii(struct net_device *dev);
static irqreturn_t fec_enet_interrupt(int irq, void * dev_id);
static void fec_enet_tx(struct net_device *dev);
static void fec_enet_rx(struct net_device *dev);
static int fec_enet_close(struct net_device *dev);
static struct net_device_stats *fec_enet_get_stats(struct net_device *dev);
static void set_multicast_list(struct net_device *dev);
static void fec_restart(struct net_device *dev, int duplex);
static void fec_stop(struct net_device *dev);
static void fec_set_mac_address(struct net_device *dev);


/* MII processing.  We keep this as simple as possible.  Requests are
 * placed on the list (if there is room).  When the request is finished
 * by the MII, an optional function may be called.
 */
typedef struct mii_list {
        uint    mii_regval;
        void    (*mii_func)(uint val, struct net_device *dev);
        struct  mii_list *mii_next;
} mii_list_t;

#define         NMII    20
static mii_list_t       mii_cmds[NMII];
static mii_list_t       *mii_free;
static mii_list_t       *mii_head;
static mii_list_t       *mii_tail;

static int      mii_queue(struct net_device *dev, int request,
                                void (*func)(uint, struct net_device *));

/* Make MII read/write commands for the FEC.
*/
#define mk_mii_read(REG)        (0x60020000 | ((REG & 0x1f) << 18))
#define mk_mii_write(REG, VAL)  (0x50020000 | ((REG & 0x1f) << 18) | \
                                                (VAL & 0xffff))
#define mk_mii_end      0

/* Transmitter timeout.
*/
#define TX_TIMEOUT (2*HZ)

/* Register definitions for the PHY.
*/

#define MII_REG_CR          0  /* Control Register                         */
#define MII_REG_SR          1  /* Status Register                          */
#define MII_REG_PHYIR1      2  /* PHY Identification Register 1            */
#define MII_REG_PHYIR2      3  /* PHY Identification Register 2            */
#define MII_REG_ANAR        4  /* A-N Advertisement Register               */
#define MII_REG_ANLPAR      5  /* A-N Link Partner Ability Register        */
#define MII_REG_ANER        6  /* A-N Expansion Register                   */
#define MII_REG_ANNPTR      7  /* A-N Next Page Transmit Register          */
#define MII_REG_ANLPRNPR    8  /* A-N Link Partner Received Next Page Reg. */

/* values for phy_status */

#define PHY_CONF_ANE    0x0001  /* 1 auto-negotiation enabled */
#define PHY_CONF_LOOP   0x0002  /* 1 loopback mode enabled */
#define PHY_CONF_SPMASK 0x00f0  /* mask for speed */
#define PHY_CONF_10HDX  0x0010  /* 10 Mbit half duplex supported */
#define PHY_CONF_10FDX  0x0020  /* 10 Mbit full duplex supported */
#define PHY_CONF_100HDX 0x0040  /* 100 Mbit half duplex supported */
#define PHY_CONF_100FDX 0x0080  /* 100 Mbit full duplex supported */

#define PHY_STAT_LINK   0x0100  /* 1 up - 0 down */
#define PHY_STAT_FAULT  0x0200  /* 1 remote fault */
#define PHY_STAT_ANC    0x0400  /* 1 auto-negotiation complete  */
#define PHY_STAT_SPMASK 0xf000  /* mask for speed */
#define PHY_STAT_10HDX  0x1000  /* 10 Mbit half duplex selected */
#define PHY_STAT_10FDX  0x2000  /* 10 Mbit full duplex selected */
#define PHY_STAT_100HDX 0x4000  /* 100 Mbit half duplex selected */
#define PHY_STAT_100FDX 0x8000  /* 100 Mbit full duplex selected */


static int
fec_enet_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
        struct fec_enet_private *fep;
        volatile fec_t  *fecp;
        volatile cbd_t  *bdp;
        unsigned short  status;

        fep = netdev_priv(dev);
        fecp = (volatile fec_t*)dev->base_addr;

        if (!fep->link) {
                /* Link is down or autonegotiation is in progress. */
                return 1;
        }

        /* Fill in a Tx ring entry */
        bdp = fep->cur_tx;

        status = bdp->cbd_sc;
#ifndef final_version
        if (status & BD_ENET_TX_READY) {
                /* Ooops.  All transmit buffers are full.  Bail out.
                 * This should not happen, since dev->tbusy should be set.
                 */
                printk("%s: tx queue full!.\n", dev->name);
                return 1;
        }
#endif

        /* Clear all of the status flags.
         */
        status &= ~BD_ENET_TX_STATS;

        /* Set buffer length and buffer pointer.
        */
        bdp->cbd_bufaddr = __pa(skb->data);
        bdp->cbd_datlen = skb->len;

        /*
         *      On some FEC implementations data must be aligned on
         *      4-byte boundaries. Use bounce buffers to copy data
         *      and get it aligned. Ugh.
         */
        if (bdp->cbd_bufaddr & 0x3) {
                unsigned int index;
                index = bdp - fep->tx_bd_base;
                memcpy(fep->tx_bounce[index], (void *) bdp->cbd_bufaddr, bdp->cbd_datlen);
                bdp->cbd_bufaddr = __pa(fep->tx_bounce[index]);
        }

        /* Save skb pointer.
        */
        fep->tx_skbuff[fep->skb_cur] = skb;

        fep->stats.tx_bytes += skb->len;
        fep->skb_cur = (fep->skb_cur+1) & TX_RING_MOD_MASK;

        /* Push the data cache so the CPM does not get stale memory
         * data.
         */
        flush_dcache_range((unsigned long)skb->data,
                           (unsigned long)skb->data + skb->len);

        spin_lock_irq(&fep->lock);

        /* Send it on its way.  Tell FEC it's ready, interrupt when done,
         * it's the last BD of the frame, and to put the CRC on the end.
         */

        status |= (BD_ENET_TX_READY | BD_ENET_TX_INTR
                        | BD_ENET_TX_LAST | BD_ENET_TX_TC);
        bdp->cbd_sc = status;

        dev->trans_start = jiffies;

        /* Trigger transmission start */
        fecp->fec_x_des_active = 0;

        /* If this was the last BD in the ring, start at the beginning again.
        */
        if (status & BD_ENET_TX_WRAP) {
                bdp = fep->tx_bd_base;
        } else {
                bdp++;
        }

        if (bdp == fep->dirty_tx) {
                fep->tx_full = 1;
                netif_stop_queue(dev);
        }

        fep->cur_tx = (cbd_t *)bdp;

        spin_unlock_irq(&fep->lock);

        return 0;
}

static void
fec_timeout(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);

        printk("%s: transmit timed out.\n", dev->name);
        fep->stats.tx_errors++;
#ifndef final_version
        {
        int     i;
        cbd_t   *bdp;

        printk("Ring data dump: cur_tx %lx%s, dirty_tx %lx cur_rx: %lx\n",
               (unsigned long)fep->cur_tx, fep->tx_full ? " (full)" : "",
               (unsigned long)fep->dirty_tx,
               (unsigned long)fep->cur_rx);

        bdp = fep->tx_bd_base;
        printk(" tx: %u buffers\n",  TX_RING_SIZE);
        for (i = 0 ; i < TX_RING_SIZE; i++) {
                printk("  %08x: %04x %04x %08x\n",
                       (uint) bdp,
                       bdp->cbd_sc,
                       bdp->cbd_datlen,
                       (int) bdp->cbd_bufaddr);
                bdp++;
        }

        bdp = fep->rx_bd_base;
        printk(" rx: %lu buffers\n",  (unsigned long) RX_RING_SIZE);
        for (i = 0 ; i < RX_RING_SIZE; i++) {
                printk("  %08x: %04x %04x %08x\n",
                       (uint) bdp,
                       bdp->cbd_sc,
                       bdp->cbd_datlen,
                       (int) bdp->cbd_bufaddr);
                bdp++;
        }
        }
#endif
        fec_restart(dev, fep->full_duplex);
        netif_wake_queue(dev);
}

/* The interrupt handler.
 * This is called from the MPC core interrupt.
 */
static irqreturn_t
fec_enet_interrupt(int irq, void * dev_id)
{
        struct  net_device *dev = dev_id;
        volatile fec_t  *fecp;
        uint    int_events;
        int handled = 0;

        fecp = (volatile fec_t*)dev->base_addr;

        /* Get the interrupt events that caused us to be here.
        */
        while ((int_events = fecp->fec_ievent) != 0) {
                fecp->fec_ievent = int_events;

                /* Handle receive event in its own function.
                 */
                if (int_events & FEC_ENET_RXF) {
                        handled = 1;
                        fec_enet_rx(dev);
                }

                /* Transmit OK, or non-fatal error. Update the buffer
                   descriptors. FEC handles all errors, we just discover
                   them as part of the transmit process.
                */
                if (int_events & FEC_ENET_TXF) {
                        handled = 1;
                        fec_enet_tx(dev);
                }

                if (int_events & FEC_ENET_MII) {
                        handled = 1;
                        fec_enet_mii(dev);
                }

        }
        return IRQ_RETVAL(handled);
}


static void
fec_enet_tx(struct net_device *dev)
{
        struct  fec_enet_private *fep;
        volatile cbd_t  *bdp;
        unsigned short status;
        struct  sk_buff *skb;

        fep = netdev_priv(dev);
        spin_lock(&fep->lock);
        bdp = fep->dirty_tx;

        while (((status = bdp->cbd_sc) & BD_ENET_TX_READY) == 0) {
                if (bdp == fep->cur_tx && fep->tx_full == 0) break;

                skb = fep->tx_skbuff[fep->skb_dirty];
                /* Check for errors. */
                if (status & (BD_ENET_TX_HB | BD_ENET_TX_LC |
                                   BD_ENET_TX_RL | BD_ENET_TX_UN |
                                   BD_ENET_TX_CSL)) {
                        fep->stats.tx_errors++;
                        if (status & BD_ENET_TX_HB)  /* No heartbeat */
                                fep->stats.tx_heartbeat_errors++;
                        if (status & BD_ENET_TX_LC)  /* Late collision */
                                fep->stats.tx_window_errors++;
                        if (status & BD_ENET_TX_RL)  /* Retrans limit */
                                fep->stats.tx_aborted_errors++;
                        if (status & BD_ENET_TX_UN)  /* Underrun */
                                fep->stats.tx_fifo_errors++;
                        if (status & BD_ENET_TX_CSL) /* Carrier lost */
                                fep->stats.tx_carrier_errors++;
                } else {
                        fep->stats.tx_packets++;
                }

#ifndef final_version
                if (status & BD_ENET_TX_READY)
                        printk("HEY! Enet xmit interrupt and TX_READY.\n");
#endif
                /* Deferred means some collisions occurred during transmit,
                 * but we eventually sent the packet OK.
                 */
                if (status & BD_ENET_TX_DEF)
                        fep->stats.collisions++;

                /* Free the sk buffer associated with this last transmit.
                 */
                dev_kfree_skb_any(skb);
                fep->tx_skbuff[fep->skb_dirty] = NULL;
                fep->skb_dirty = (fep->skb_dirty + 1) & TX_RING_MOD_MASK;

                /* Update pointer to next buffer descriptor to be transmitted.
                 */
                if (status & BD_ENET_TX_WRAP)
                        bdp = fep->tx_bd_base;
                else
                        bdp++;

                /* Since we have freed up a buffer, the ring is no longer
                 * full.
                 */
                if (fep->tx_full) {
                        fep->tx_full = 0;
                        if (netif_queue_stopped(dev))
                                netif_wake_queue(dev);
                }
        }
        fep->dirty_tx = (cbd_t *)bdp;
        spin_unlock(&fep->lock);
}


/* During a receive, the cur_rx points to the current incoming buffer.
 * When we update through the ring, if the next incoming buffer has
 * not been given to the system, we just set the empty indicator,
 * effectively tossing the packet.
 */
static void
fec_enet_rx(struct net_device *dev)
{
        struct  fec_enet_private *fep;
        volatile fec_t  *fecp;
        volatile cbd_t *bdp;
        unsigned short status;
        struct  sk_buff *skb;
        ushort  pkt_len;
        __u8 *data;

#ifdef CONFIG_M532x
        flush_cache_all();
#endif

        fep = netdev_priv(dev);
        fecp = (volatile fec_t*)dev->base_addr;

        /* First, grab all of the stats for the incoming packet.
         * These get messed up if we get called due to a busy condition.
         */
        bdp = fep->cur_rx;

while (!((status = bdp->cbd_sc) & BD_ENET_RX_EMPTY)) {

#ifndef final_version
        /* Since we have allocated space to hold a complete frame,
         * the last indicator should be set.
         */
        if ((status & BD_ENET_RX_LAST) == 0)
                printk("FEC ENET: rcv is not +last\n");
#endif

        if (!fep->opened)
                goto rx_processing_done;

        /* Check for errors. */
        if (status & (BD_ENET_RX_LG | BD_ENET_RX_SH | BD_ENET_RX_NO |
                           BD_ENET_RX_CR | BD_ENET_RX_OV)) {
                fep->stats.rx_errors++;
                if (status & (BD_ENET_RX_LG | BD_ENET_RX_SH)) {
                /* Frame too long or too short. */
                        fep->stats.rx_length_errors++;
                }
                if (status & BD_ENET_RX_NO)     /* Frame alignment */
                        fep->stats.rx_frame_errors++;
                if (status & BD_ENET_RX_CR)     /* CRC Error */
                        fep->stats.rx_crc_errors++;
                if (status & BD_ENET_RX_OV)     /* FIFO overrun */
                        fep->stats.rx_fifo_errors++;
        }

        /* Report late collisions as a frame error.
         * On this error, the BD is closed, but we don't know what we
         * have in the buffer.  So, just drop this frame on the floor.
         */
        if (status & BD_ENET_RX_CL) {
                fep->stats.rx_errors++;
                fep->stats.rx_frame_errors++;
                goto rx_processing_done;
        }

        /* Process the incoming frame.
         */
        fep->stats.rx_packets++;
        pkt_len = bdp->cbd_datlen;
        fep->stats.rx_bytes += pkt_len;
        data = (__u8*)__va(bdp->cbd_bufaddr);

        /* This does 16 byte alignment, exactly what we need.
         * The packet length includes FCS, but we don't want to
         * include that when passing upstream as it messes up
         * bridging applications.
         */
        skb = dev_alloc_skb(pkt_len-4);

        if (skb == NULL) {
                printk("%s: Memory squeeze, dropping packet.\n", dev->name);
                fep->stats.rx_dropped++;
        } else {
                skb_put(skb,pkt_len-4); /* Make room */
                skb_copy_to_linear_data(skb, data, pkt_len-4);
                skb->protocol=eth_type_trans(skb,dev);
                netif_rx(skb);
        }
  rx_processing_done:

        /* Clear the status flags for this buffer.
        */
        status &= ~BD_ENET_RX_STATS;

        /* Mark the buffer empty.
        */
        status |= BD_ENET_RX_EMPTY;
        bdp->cbd_sc = status;

        /* Update BD pointer to next entry.
        */
        if (status & BD_ENET_RX_WRAP)
                bdp = fep->rx_bd_base;
        else
                bdp++;

#if 1
        /* Doing this here will keep the FEC running while we process
         * incoming frames.  On a heavily loaded network, we should be
         * able to keep up at the expense of system resources.
         */
        fecp->fec_r_des_active = 0;
#endif
   } /* while (!((status = bdp->cbd_sc) & BD_ENET_RX_EMPTY)) */
        fep->cur_rx = (cbd_t *)bdp;

#if 0
        /* Doing this here will allow us to process all frames in the
         * ring before the FEC is allowed to put more there.  On a heavily
         * loaded network, some frames may be lost.  Unfortunately, this
         * increases the interrupt overhead since we can potentially work
         * our way back to the interrupt return only to come right back
         * here.
         */
        fecp->fec_r_des_active = 0;
#endif
}


/* called from interrupt context */
static void
fec_enet_mii(struct net_device *dev)
{
        struct  fec_enet_private *fep;
        volatile fec_t  *ep;
        mii_list_t      *mip;
        uint            mii_reg;

        fep = netdev_priv(dev);
        ep = fep->hwp;
        mii_reg = ep->fec_mii_data;

        spin_lock(&fep->lock);

        if ((mip = mii_head) == NULL) {
                printk("MII and no head!\n");
                goto unlock;
        }

        if (mip->mii_func != NULL)
                (*(mip->mii_func))(mii_reg, dev);

        mii_head = mip->mii_next;
        mip->mii_next = mii_free;
        mii_free = mip;

        if ((mip = mii_head) != NULL)
                ep->fec_mii_data = mip->mii_regval;

unlock:
        spin_unlock(&fep->lock);
}

static int
mii_queue(struct net_device *dev, int regval, void (*func)(uint, struct net_device *))
{
        struct fec_enet_private *fep;
        unsigned long   flags;
        mii_list_t      *mip;
        int             retval;

        /* Add PHY address to register command.
        */
        fep = netdev_priv(dev);
        regval |= fep->phy_addr << 23;

        retval = 0;

        spin_lock_irqsave(&fep->lock,flags);

        if ((mip = mii_free) != NULL) {
                mii_free = mip->mii_next;
                mip->mii_regval = regval;
                mip->mii_func = func;
                mip->mii_next = NULL;
                if (mii_head) {
                        mii_tail->mii_next = mip;
                        mii_tail = mip;
                }
                else {
                        mii_head = mii_tail = mip;
                        fep->hwp->fec_mii_data = regval;
                }
        }
        else {
                retval = 1;
        }

        spin_unlock_irqrestore(&fep->lock,flags);

        return(retval);
}

static void mii_do_cmd(struct net_device *dev, const phy_cmd_t *c)
{
        int k;

        if(!c)
                return;

        for(k = 0; (c+k)->mii_data != mk_mii_end; k++) {
                mii_queue(dev, (c+k)->mii_data, (c+k)->funct);
        }
}

static void mii_parse_sr(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);
        uint status;

        status = *s & ~(PHY_STAT_LINK | PHY_STAT_FAULT | PHY_STAT_ANC);

        if (mii_reg & 0x0004)
                status |= PHY_STAT_LINK;
        if (mii_reg & 0x0010)
                status |= PHY_STAT_FAULT;
        if (mii_reg & 0x0020)
                status |= PHY_STAT_ANC;

        *s = status;
}

static void mii_parse_cr(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);
        uint status;

        status = *s & ~(PHY_CONF_ANE | PHY_CONF_LOOP);

        if (mii_reg & 0x1000)
                status |= PHY_CONF_ANE;
        if (mii_reg & 0x4000)
                status |= PHY_CONF_LOOP;
        *s = status;
}

static void mii_parse_anar(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);
        uint status;

        status = *s & ~(PHY_CONF_SPMASK);

        if (mii_reg & 0x0020)
                status |= PHY_CONF_10HDX;
        if (mii_reg & 0x0040)
                status |= PHY_CONF_10FDX;
        if (mii_reg & 0x0080)
                status |= PHY_CONF_100HDX;
        if (mii_reg & 0x00100)
                status |= PHY_CONF_100FDX;
        *s = status;
}

/* ------------------------------------------------------------------------- */
/* The Level one LXT970 is used by many boards                               */

#define MII_LXT970_MIRROR    16  /* Mirror register           */
#define MII_LXT970_IER       17  /* Interrupt Enable Register */
#define MII_LXT970_ISR       18  /* Interrupt Status Register */
#define MII_LXT970_CONFIG    19  /* Configuration Register    */
#define MII_LXT970_CSR       20  /* Chip Status Register      */

static void mii_parse_lxt970_csr(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);
        uint status;

        status = *s & ~(PHY_STAT_SPMASK);
        if (mii_reg & 0x0800) {
                if (mii_reg & 0x1000)
                        status |= PHY_STAT_100FDX;
                else
                        status |= PHY_STAT_100HDX;
        } else {
                if (mii_reg & 0x1000)
                        status |= PHY_STAT_10FDX;
                else
                        status |= PHY_STAT_10HDX;
        }
        *s = status;
}

static phy_cmd_t const phy_cmd_lxt970_config[] = {
                { mk_mii_read(MII_REG_CR), mii_parse_cr },
                { mk_mii_read(MII_REG_ANAR), mii_parse_anar },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_lxt970_startup[] = { /* enable interrupts */
                { mk_mii_write(MII_LXT970_IER, 0x0002), NULL },
                { mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_lxt970_ack_int[] = {
                /* read SR and ISR to acknowledge */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_read(MII_LXT970_ISR), NULL },

                /* find out the current status */
                { mk_mii_read(MII_LXT970_CSR), mii_parse_lxt970_csr },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_lxt970_shutdown[] = { /* disable interrupts */
                { mk_mii_write(MII_LXT970_IER, 0x0000), NULL },
                { mk_mii_end, }
        };
static phy_info_t const phy_info_lxt970 = {
        .id = 0x07810000,
        .name = "LXT970",
        .config = phy_cmd_lxt970_config,
        .startup = phy_cmd_lxt970_startup,
        .ack_int = phy_cmd_lxt970_ack_int,
        .shutdown = phy_cmd_lxt970_shutdown
};

/* ------------------------------------------------------------------------- */
/* The Level one LXT971 is used on some of my custom boards                  */

/* register definitions for the 971 */

#define MII_LXT971_PCR       16  /* Port Control Register     */
#define MII_LXT971_SR2       17  /* Status Register 2         */
#define MII_LXT971_IER       18  /* Interrupt Enable Register */
#define MII_LXT971_ISR       19  /* Interrupt Status Register */
#define MII_LXT971_LCR       20  /* LED Control Register      */
#define MII_LXT971_TCR       30  /* Transmit Control Register */

/*
 * I had some nice ideas of running the MDIO faster...
 * The 971 should support 8MHz and I tried it, but things acted really
 * weird, so 2.5 MHz ought to be enough for anyone...
 */

static void mii_parse_lxt971_sr2(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);
        uint status;

        status = *s & ~(PHY_STAT_SPMASK | PHY_STAT_LINK | PHY_STAT_ANC);

        if (mii_reg & 0x0400) {
                fep->link = 1;
                status |= PHY_STAT_LINK;
        } else {
                fep->link = 0;
        }
        if (mii_reg & 0x0080)
                status |= PHY_STAT_ANC;
        if (mii_reg & 0x4000) {
                if (mii_reg & 0x0200)
                        status |= PHY_STAT_100FDX;
                else
                        status |= PHY_STAT_100HDX;
        } else {
                if (mii_reg & 0x0200)
                        status |= PHY_STAT_10FDX;
                else
                        status |= PHY_STAT_10HDX;
        }
        if (mii_reg & 0x0008)
                status |= PHY_STAT_FAULT;

        *s = status;
}

static phy_cmd_t const phy_cmd_lxt971_config[] = {
                /* limit to 10MBit because my prototype board
                 * doesn't work with 100. */
                { mk_mii_read(MII_REG_CR), mii_parse_cr },
                { mk_mii_read(MII_REG_ANAR), mii_parse_anar },
                { mk_mii_read(MII_LXT971_SR2), mii_parse_lxt971_sr2 },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_lxt971_startup[] = {  /* enable interrupts */
                { mk_mii_write(MII_LXT971_IER, 0x00f2), NULL },
                { mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
                { mk_mii_write(MII_LXT971_LCR, 0xd422), NULL }, /* LED config */
                /* Somehow does the 971 tell me that the link is down
                 * the first read after power-up.
                 * read here to get a valid value in ack_int */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_lxt971_ack_int[] = {
                /* acknowledge the int before reading status ! */
                { mk_mii_read(MII_LXT971_ISR), NULL },
                /* find out the current status */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_read(MII_LXT971_SR2), mii_parse_lxt971_sr2 },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_lxt971_shutdown[] = { /* disable interrupts */
                { mk_mii_write(MII_LXT971_IER, 0x0000), NULL },
                { mk_mii_end, }
        };
static phy_info_t const phy_info_lxt971 = {
        .id = 0x0001378e,
        .name = "LXT971",
        .config = phy_cmd_lxt971_config,
        .startup = phy_cmd_lxt971_startup,
        .ack_int = phy_cmd_lxt971_ack_int,
        .shutdown = phy_cmd_lxt971_shutdown
};

/* ------------------------------------------------------------------------- */
/* The Quality Semiconductor QS6612 is used on the RPX CLLF                  */

/* register definitions */

#define MII_QS6612_MCR       17  /* Mode Control Register      */
#define MII_QS6612_FTR       27  /* Factory Test Register      */
#define MII_QS6612_MCO       28  /* Misc. Control Register     */
#define MII_QS6612_ISR       29  /* Interrupt Source Register  */
#define MII_QS6612_IMR       30  /* Interrupt Mask Register    */
#define MII_QS6612_PCR       31  /* 100BaseTx PHY Control Reg. */

static void mii_parse_qs6612_pcr(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);
        uint status;

        status = *s & ~(PHY_STAT_SPMASK);

        switch((mii_reg >> 2) & 7) {
        case 1: status |= PHY_STAT_10HDX; break;
        case 2: status |= PHY_STAT_100HDX; break;
        case 5: status |= PHY_STAT_10FDX; break;
        case 6: status |= PHY_STAT_100FDX; break;
}

        *s = status;
}

static phy_cmd_t const phy_cmd_qs6612_config[] = {
                /* The PHY powers up isolated on the RPX,
                 * so send a command to allow operation.
                 */
                { mk_mii_write(MII_QS6612_PCR, 0x0dc0), NULL },

                /* parse cr and anar to get some info */
                { mk_mii_read(MII_REG_CR), mii_parse_cr },
                { mk_mii_read(MII_REG_ANAR), mii_parse_anar },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_qs6612_startup[] = {  /* enable interrupts */
                { mk_mii_write(MII_QS6612_IMR, 0x003a), NULL },
                { mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_qs6612_ack_int[] = {
                /* we need to read ISR, SR and ANER to acknowledge */
                { mk_mii_read(MII_QS6612_ISR), NULL },
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_read(MII_REG_ANER), NULL },

                /* read pcr to get info */
                { mk_mii_read(MII_QS6612_PCR), mii_parse_qs6612_pcr },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_qs6612_shutdown[] = { /* disable interrupts */
                { mk_mii_write(MII_QS6612_IMR, 0x0000), NULL },
                { mk_mii_end, }
        };
static phy_info_t const phy_info_qs6612 = {
        .id = 0x00181440,
        .name = "QS6612",
        .config = phy_cmd_qs6612_config,
        .startup = phy_cmd_qs6612_startup,
        .ack_int = phy_cmd_qs6612_ack_int,
        .shutdown = phy_cmd_qs6612_shutdown
};

/* ------------------------------------------------------------------------- */
/* AMD AM79C874 phy                                                          */

/* register definitions for the 874 */

#define MII_AM79C874_MFR       16  /* Miscellaneous Feature Register */
#define MII_AM79C874_ICSR      17  /* Interrupt/Status Register      */
#define MII_AM79C874_DR        18  /* Diagnostic Register            */
#define MII_AM79C874_PMLR      19  /* Power and Loopback Register    */
#define MII_AM79C874_MCR       21  /* ModeControl Register           */
#define MII_AM79C874_DC        23  /* Disconnect Counter             */
#define MII_AM79C874_REC       24  /* Recieve Error Counter          */

static void mii_parse_am79c874_dr(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);
        uint status;

        status = *s & ~(PHY_STAT_SPMASK | PHY_STAT_ANC);

        if (mii_reg & 0x0080)
                status |= PHY_STAT_ANC;
        if (mii_reg & 0x0400)
                status |= ((mii_reg & 0x0800) ? PHY_STAT_100FDX : PHY_STAT_100HDX);
        else
                status |= ((mii_reg & 0x0800) ? PHY_STAT_10FDX : PHY_STAT_10HDX);

        *s = status;
}

static phy_cmd_t const phy_cmd_am79c874_config[] = {
                { mk_mii_read(MII_REG_CR), mii_parse_cr },
                { mk_mii_read(MII_REG_ANAR), mii_parse_anar },
                { mk_mii_read(MII_AM79C874_DR), mii_parse_am79c874_dr },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_am79c874_startup[] = {  /* enable interrupts */
                { mk_mii_write(MII_AM79C874_ICSR, 0xff00), NULL },
                { mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_am79c874_ack_int[] = {
                /* find out the current status */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_read(MII_AM79C874_DR), mii_parse_am79c874_dr },
                /* we only need to read ISR to acknowledge */
                { mk_mii_read(MII_AM79C874_ICSR), NULL },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_am79c874_shutdown[] = { /* disable interrupts */
                { mk_mii_write(MII_AM79C874_ICSR, 0x0000), NULL },
                { mk_mii_end, }
        };
static phy_info_t const phy_info_am79c874 = {
        .id = 0x00022561,
        .name = "AM79C874",
        .config = phy_cmd_am79c874_config,
        .startup = phy_cmd_am79c874_startup,
        .ack_int = phy_cmd_am79c874_ack_int,
        .shutdown = phy_cmd_am79c874_shutdown
};


/* ------------------------------------------------------------------------- */
/* Kendin KS8721BL phy                                                       */

/* register definitions for the 8721 */

#define MII_KS8721BL_RXERCR     21
#define MII_KS8721BL_ICSR       22
#define MII_KS8721BL_PHYCR      31

static phy_cmd_t const phy_cmd_ks8721bl_config[] = {
                { mk_mii_read(MII_REG_CR), mii_parse_cr },
                { mk_mii_read(MII_REG_ANAR), mii_parse_anar },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_ks8721bl_startup[] = {  /* enable interrupts */
                { mk_mii_write(MII_KS8721BL_ICSR, 0xff00), NULL },
                { mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_ks8721bl_ack_int[] = {
                /* find out the current status */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                /* we only need to read ISR to acknowledge */
                { mk_mii_read(MII_KS8721BL_ICSR), NULL },
                { mk_mii_end, }
        };
static phy_cmd_t const phy_cmd_ks8721bl_shutdown[] = { /* disable interrupts */
                { mk_mii_write(MII_KS8721BL_ICSR, 0x0000), NULL },
                { mk_mii_end, }
        };
static phy_info_t const phy_info_ks8721bl = {
        .id = 0x00022161,
        .name = "KS8721BL",
        .config = phy_cmd_ks8721bl_config,
        .startup = phy_cmd_ks8721bl_startup,
        .ack_int = phy_cmd_ks8721bl_ack_int,
        .shutdown = phy_cmd_ks8721bl_shutdown
};

/* ------------------------------------------------------------------------- */
/* register definitions for the DP83848 */

#define MII_DP8384X_PHYSTST    16  /* PHY Status Register */

static void mii_parse_dp8384x_sr2(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = dev->priv;
        volatile uint *s = &(fep->phy_status);

        *s &= ~(PHY_STAT_SPMASK | PHY_STAT_LINK | PHY_STAT_ANC);

        /* Link up */
        if (mii_reg & 0x0001) {
                fep->link = 1;
                *s |= PHY_STAT_LINK;
        } else
                fep->link = 0;
        /* Status of link */
        if (mii_reg & 0x0010)   /* Autonegotioation complete */
                *s |= PHY_STAT_ANC;
        if (mii_reg & 0x0002) {   /* 10MBps? */
                if (mii_reg & 0x0004)   /* Full Duplex? */
                        *s |= PHY_STAT_10FDX;
                else
                        *s |= PHY_STAT_10HDX;
        } else {                  /* 100 Mbps? */
                if (mii_reg & 0x0004)   /* Full Duplex? */
                        *s |= PHY_STAT_100FDX;
                else
                        *s |= PHY_STAT_100HDX;
        }
        if (mii_reg & 0x0008)
                *s |= PHY_STAT_FAULT;
}

static phy_info_t phy_info_dp83848= {
        0x020005c9,
        "DP83848",

        (const phy_cmd_t []) {  /* config */
                { mk_mii_read(MII_REG_CR), mii_parse_cr },
                { mk_mii_read(MII_REG_ANAR), mii_parse_anar },
                { mk_mii_read(MII_DP8384X_PHYSTST), mii_parse_dp8384x_sr2 },
                { mk_mii_end, }
        },
        (const phy_cmd_t []) {  /* startup - enable interrupts */
                { mk_mii_write(MII_REG_CR, 0x1200), NULL }, /* autonegotiate */
                { mk_mii_read(MII_REG_SR), mii_parse_sr },
                { mk_mii_end, }
        },
        (const phy_cmd_t []) { /* ack_int - never happens, no interrupt */
                { mk_mii_end, }
        },
        (const phy_cmd_t []) {  /* shutdown */
                { mk_mii_end, }
        },
};

/* ------------------------------------------------------------------------- */

static phy_info_t const * const phy_info[] = {
        &phy_info_lxt970,
        &phy_info_lxt971,
        &phy_info_qs6612,
        &phy_info_am79c874,
        &phy_info_ks8721bl,
        &phy_info_dp83848,
        NULL
};

/* ------------------------------------------------------------------------- */
#if !defined(CONFIG_M532x)
#ifdef CONFIG_RPXCLASSIC
static void
mii_link_interrupt(void *dev_id);
#else
static irqreturn_t
mii_link_interrupt(int irq, void * dev_id);
#endif
#endif

#if defined(CONFIG_M5272)

/*
 *      Code specific to Coldfire 5272 setup.
 */
static void __inline__ fec_request_intrs(struct net_device *dev)
{
        volatile unsigned long *icrp;
        static const struct idesc {
                char *name;
                unsigned short irq;
                irq_handler_t handler;
        } *idp, id[] = {
                { "fec(RX)", 86, fec_enet_interrupt },
                { "fec(TX)", 87, fec_enet_interrupt },
                { "fec(OTHER)", 88, fec_enet_interrupt },
                { "fec(MII)", 66, mii_link_interrupt },
                { NULL },
        };

        /* Setup interrupt handlers. */
        for (idp = id; idp->name; idp++) {
                if (request_irq(idp->irq, idp->handler, 0, idp->name, dev) != 0)
                        printk("FEC: Could not allocate %s IRQ(%d)!\n", idp->name, idp->irq);
        }

        /* Unmask interrupt at ColdFire 5272 SIM */
        icrp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_ICR3);
        *icrp = 0x00000ddd;
        icrp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_ICR1);
        *icrp = 0x0d000000;
}

static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
{
        volatile fec_t *fecp;

        fecp = fep->hwp;
        fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x04;
        fecp->fec_x_cntrl = 0x00;

        /*
         * Set MII speed to 2.5 MHz
         * See 5272 manual section 11.5.8: MSCR
         */
        fep->phy_speed = ((((MCF_CLK / 4) / (2500000 / 10)) + 5) / 10) * 2;
        fecp->fec_mii_speed = fep->phy_speed;

        fec_restart(dev, 0);
}

static void __inline__ fec_get_mac(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile fec_t *fecp;
        unsigned char *iap, tmpaddr[ETH_ALEN];

        fecp = fep->hwp;

        if (FEC_FLASHMAC) {
                /*
                 * Get MAC address from FLASH.
                 * If it is all 1's or 0's, use the default.
                 */
                iap = (unsigned char *)FEC_FLASHMAC;
                if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
                    (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
                        iap = fec_mac_default;
                if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
                    (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
                        iap = fec_mac_default;
        } else {
                *((unsigned long *) &tmpaddr[0]) = fecp->fec_addr_low;
                *((unsigned short *) &tmpaddr[4]) = (fecp->fec_addr_high >> 16);
                iap = &tmpaddr[0];
        }

        memcpy(dev->dev_addr, iap, ETH_ALEN);

        /* Adjust MAC if using default MAC address */
        if (iap == fec_mac_default)
                 dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
}

static void __inline__ fec_enable_phy_intr(void)
{
}

static void __inline__ fec_disable_phy_intr(void)
{
        volatile unsigned long *icrp;
        icrp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_ICR1);
        *icrp = 0x08000000;
}

static void __inline__ fec_phy_ack_intr(void)
{
        volatile unsigned long *icrp;
        /* Acknowledge the interrupt */
        icrp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_ICR1);
        *icrp = 0x0d000000;
}

static void __inline__ fec_localhw_setup(void)
{
}

/*
 *      Do not need to make region uncached on 5272.
 */
static void __inline__ fec_uncache(unsigned long addr)
{
}

/* ------------------------------------------------------------------------- */

#elif defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x)

/*
 *      Code specific to Coldfire 5230/5231/5232/5234/5235,
 *      the 5270/5271/5274/5275 and 5280/5282 setups.
 */
static void __inline__ fec_request_intrs(struct net_device *dev)
{
        struct fec_enet_private *fep;
        int b;
        static const struct idesc {
                char *name;
                unsigned short irq;
        } *idp, id[] = {
                { "fec(TXF)", 23 },
                { "fec(TXB)", 24 },
                { "fec(TXFIFO)", 25 },
                { "fec(TXCR)", 26 },
                { "fec(RXF)", 27 },
                { "fec(RXB)", 28 },
                { "fec(MII)", 29 },
                { "fec(LC)", 30 },
                { "fec(HBERR)", 31 },
                { "fec(GRA)", 32 },
                { "fec(EBERR)", 33 },
                { "fec(BABT)", 34 },
                { "fec(BABR)", 35 },
                { NULL },
        };

        fep = netdev_priv(dev);
        b = (fep->index) ? 128 : 64;

        /* Setup interrupt handlers. */
        for (idp = id; idp->name; idp++) {
                if (request_irq(b+idp->irq, fec_enet_interrupt, 0, idp->name, dev) != 0)
                        printk("FEC: Could not allocate %s IRQ(%d)!\n", idp->name, b+idp->irq);
        }

        /* Unmask interrupts at ColdFire 5280/5282 interrupt controller */
        {
                volatile unsigned char  *icrp;
                volatile unsigned long  *imrp;
                int i, ilip;

                b = (fep->index) ? MCFICM_INTC1 : MCFICM_INTC0;
                icrp = (volatile unsigned char *) (MCF_IPSBAR + b +
                        MCFINTC_ICR0);
                for (i = 23, ilip = 0x28; (i < 36); i++)
                        icrp[i] = ilip--;

                imrp = (volatile unsigned long *) (MCF_IPSBAR + b +
                        MCFINTC_IMRH);
                *imrp &= ~0x0000000f;
                imrp = (volatile unsigned long *) (MCF_IPSBAR + b +
                        MCFINTC_IMRL);
                *imrp &= ~0xff800001;
        }

#if defined(CONFIG_M528x)
        /* Set up gpio outputs for MII lines */
        {
                volatile u16 *gpio_paspar;
                volatile u8 *gpio_pehlpar;

                gpio_paspar = (volatile u16 *) (MCF_IPSBAR + 0x100056);
                gpio_pehlpar = (volatile u16 *) (MCF_IPSBAR + 0x100058);
                *gpio_paspar |= 0x0f00;
                *gpio_pehlpar = 0xc0;
        }
#endif

#if defined(CONFIG_M527x)
        /* Set up gpio outputs for MII lines */
        {
                volatile u8 *gpio_par_fec;
                volatile u16 *gpio_par_feci2c;

                gpio_par_feci2c = (volatile u16 *)(MCF_IPSBAR + 0x100082);
                /* Set up gpio outputs for FEC0 MII lines */
                gpio_par_fec = (volatile u8 *)(MCF_IPSBAR + 0x100078);

                *gpio_par_feci2c |= 0x0f00;
                *gpio_par_fec |= 0xc0;

#if defined(CONFIG_FEC2)
                /* Set up gpio outputs for FEC1 MII lines */
                gpio_par_fec = (volatile u8 *)(MCF_IPSBAR + 0x100079);

                *gpio_par_feci2c |= 0x00a0;
                *gpio_par_fec |= 0xc0;
#endif /* CONFIG_FEC2 */
        }
#endif /* CONFIG_M527x */
}

static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
{
        volatile fec_t *fecp;

        fecp = fep->hwp;
        fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x04;
        fecp->fec_x_cntrl = 0x00;

        /*
         * Set MII speed to 2.5 MHz
         * See 5282 manual section 17.5.4.7: MSCR
         */
        fep->phy_speed = ((((MCF_CLK / 2) / (2500000 / 10)) + 5) / 10) * 2;
        fecp->fec_mii_speed = fep->phy_speed;

        fec_restart(dev, 0);
}

static void __inline__ fec_get_mac(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile fec_t *fecp;
        unsigned char *iap, tmpaddr[ETH_ALEN];

        fecp = fep->hwp;

        if (FEC_FLASHMAC) {
                /*
                 * Get MAC address from FLASH.
                 * If it is all 1's or 0's, use the default.
                 */
                iap = FEC_FLASHMAC;
                if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
                    (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
                        iap = fec_mac_default;
                if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
                    (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
                        iap = fec_mac_default;
        } else {
                *((unsigned long *) &tmpaddr[0]) = fecp->fec_addr_low;
                *((unsigned short *) &tmpaddr[4]) = (fecp->fec_addr_high >> 16);
                iap = &tmpaddr[0];
        }

        memcpy(dev->dev_addr, iap, ETH_ALEN);

        /* Adjust MAC if using default MAC address */
        if (iap == fec_mac_default)
                dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
}

static void __inline__ fec_enable_phy_intr(void)
{
}

static void __inline__ fec_disable_phy_intr(void)
{
}

static void __inline__ fec_phy_ack_intr(void)
{
}

static void __inline__ fec_localhw_setup(void)
{
}

/*
 *      Do not need to make region uncached on 5272.
 */
static void __inline__ fec_uncache(unsigned long addr)
{
}

/* ------------------------------------------------------------------------- */

#elif defined(CONFIG_M520x)

/*
 *      Code specific to Coldfire 520x
 */
static void __inline__ fec_request_intrs(struct net_device *dev)
{
        struct fec_enet_private *fep;
        int b;
        static const struct idesc {
                char *name;
                unsigned short irq;
        } *idp, id[] = {
                { "fec(TXF)", 23 },
                { "fec(TXB)", 24 },
                { "fec(TXFIFO)", 25 },
                { "fec(TXCR)", 26 },
                { "fec(RXF)", 27 },
                { "fec(RXB)", 28 },
                { "fec(MII)", 29 },
                { "fec(LC)", 30 },
                { "fec(HBERR)", 31 },
                { "fec(GRA)", 32 },
                { "fec(EBERR)", 33 },
                { "fec(BABT)", 34 },
                { "fec(BABR)", 35 },
                { NULL },
        };

        fep = netdev_priv(dev);
        b = 64 + 13;

        /* Setup interrupt handlers. */
        for (idp = id; idp->name; idp++) {
                if (request_irq(b+idp->irq,fec_enet_interrupt,0,idp->name,dev)!=0)
                        printk("FEC: Could not allocate %s IRQ(%d)!\n", idp->name, b+idp->irq);
        }

        /* Unmask interrupts at ColdFire interrupt controller */
        {
                volatile unsigned char  *icrp;
                volatile unsigned long  *imrp;

                icrp = (volatile unsigned char *) (MCF_IPSBAR + MCFICM_INTC0 +
                        MCFINTC_ICR0);
                for (b = 36; (b < 49); b++)
                        icrp[b] = 0x04;
                imrp = (volatile unsigned long *) (MCF_IPSBAR + MCFICM_INTC0 +
                        MCFINTC_IMRH);
                *imrp &= ~0x0001FFF0;
        }
        *(volatile unsigned char *)(MCF_IPSBAR + MCF_GPIO_PAR_FEC) |= 0xf0;
        *(volatile unsigned char *)(MCF_IPSBAR + MCF_GPIO_PAR_FECI2C) |= 0x0f;
}

static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
{
        volatile fec_t *fecp;

        fecp = fep->hwp;
        fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x04;
        fecp->fec_x_cntrl = 0x00;

        /*
         * Set MII speed to 2.5 MHz
         * See 5282 manual section 17.5.4.7: MSCR
         */
        fep->phy_speed = ((((MCF_CLK / 2) / (2500000 / 10)) + 5) / 10) * 2;
        fecp->fec_mii_speed = fep->phy_speed;

        fec_restart(dev, 0);
}

static void __inline__ fec_get_mac(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile fec_t *fecp;
        unsigned char *iap, tmpaddr[ETH_ALEN];

        fecp = fep->hwp;

        if (FEC_FLASHMAC) {
                /*
                 * Get MAC address from FLASH.
                 * If it is all 1's or 0's, use the default.
                 */
                iap = FEC_FLASHMAC;
                if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
                   (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
                        iap = fec_mac_default;
                if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
                   (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
                        iap = fec_mac_default;
        } else {
                *((unsigned long *) &tmpaddr[0]) = fecp->fec_addr_low;
                *((unsigned short *) &tmpaddr[4]) = (fecp->fec_addr_high >> 16);
                iap = &tmpaddr[0];
        }

        memcpy(dev->dev_addr, iap, ETH_ALEN);

        /* Adjust MAC if using default MAC address */
        if (iap == fec_mac_default)
                dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
}

static void __inline__ fec_enable_phy_intr(void)
{
}

static void __inline__ fec_disable_phy_intr(void)
{
}

static void __inline__ fec_phy_ack_intr(void)
{
}

static void __inline__ fec_localhw_setup(void)
{
}

static void __inline__ fec_uncache(unsigned long addr)
{
}

/* ------------------------------------------------------------------------- */

#elif defined(CONFIG_M532x)
/*
 * Code specific for M532x
 */
static void __inline__ fec_request_intrs(struct net_device *dev)
{
        struct fec_enet_private *fep;
        int b;
        static const struct idesc {
                char *name;
                unsigned short irq;
        } *idp, id[] = {
            { "fec(TXF)", 36 },
            { "fec(TXB)", 37 },
            { "fec(TXFIFO)", 38 },
            { "fec(TXCR)", 39 },
            { "fec(RXF)", 40 },
            { "fec(RXB)", 41 },
            { "fec(MII)", 42 },
            { "fec(LC)", 43 },
            { "fec(HBERR)", 44 },
            { "fec(GRA)", 45 },
            { "fec(EBERR)", 46 },
            { "fec(BABT)", 47 },
            { "fec(BABR)", 48 },
            { NULL },
        };

        fep = netdev_priv(dev);
        b = (fep->index) ? 128 : 64;

        /* Setup interrupt handlers. */
        for (idp = id; idp->name; idp++) {
                if (request_irq(b+idp->irq,fec_enet_interrupt,0,idp->name,dev)!=0)
                        printk("FEC: Could not allocate %s IRQ(%d)!\n",
                                idp->name, b+idp->irq);
        }

        /* Unmask interrupts */
        MCF_INTC0_ICR36 = 0x2;
        MCF_INTC0_ICR37 = 0x2;
        MCF_INTC0_ICR38 = 0x2;
        MCF_INTC0_ICR39 = 0x2;
        MCF_INTC0_ICR40 = 0x2;
        MCF_INTC0_ICR41 = 0x2;
        MCF_INTC0_ICR42 = 0x2;
        MCF_INTC0_ICR43 = 0x2;
        MCF_INTC0_ICR44 = 0x2;
        MCF_INTC0_ICR45 = 0x2;
        MCF_INTC0_ICR46 = 0x2;
        MCF_INTC0_ICR47 = 0x2;
        MCF_INTC0_ICR48 = 0x2;

        MCF_INTC0_IMRH &= ~(
                MCF_INTC_IMRH_INT_MASK36 |
                MCF_INTC_IMRH_INT_MASK37 |
                MCF_INTC_IMRH_INT_MASK38 |
                MCF_INTC_IMRH_INT_MASK39 |
                MCF_INTC_IMRH_INT_MASK40 |
                MCF_INTC_IMRH_INT_MASK41 |
                MCF_INTC_IMRH_INT_MASK42 |
                MCF_INTC_IMRH_INT_MASK43 |
                MCF_INTC_IMRH_INT_MASK44 |
                MCF_INTC_IMRH_INT_MASK45 |
                MCF_INTC_IMRH_INT_MASK46 |
                MCF_INTC_IMRH_INT_MASK47 |
                MCF_INTC_IMRH_INT_MASK48 );

        /* Set up gpio outputs for MII lines */
        MCF_GPIO_PAR_FECI2C |= (0 |
                MCF_GPIO_PAR_FECI2C_PAR_MDC_EMDC |
                MCF_GPIO_PAR_FECI2C_PAR_MDIO_EMDIO);
        MCF_GPIO_PAR_FEC = (0 |
                MCF_GPIO_PAR_FEC_PAR_FEC_7W_FEC |
                MCF_GPIO_PAR_FEC_PAR_FEC_MII_FEC);
}

static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
{
        volatile fec_t *fecp;

        fecp = fep->hwp;
        fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x04;
        fecp->fec_x_cntrl = 0x00;

        /*
         * Set MII speed to 2.5 MHz
         */
        fep->phy_speed = ((((MCF_CLK / 2) / (2500000 / 10)) + 5) / 10) * 2;
        fecp->fec_mii_speed = fep->phy_speed;

        fec_restart(dev, 0);
}

static void __inline__ fec_get_mac(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile fec_t *fecp;
        unsigned char *iap, tmpaddr[ETH_ALEN];

        fecp = fep->hwp;

        if (FEC_FLASHMAC) {
                /*
                 * Get MAC address from FLASH.
                 * If it is all 1's or 0's, use the default.
                 */
                iap = FEC_FLASHMAC;
                if ((iap[0] == 0) && (iap[1] == 0) && (iap[2] == 0) &&
                    (iap[3] == 0) && (iap[4] == 0) && (iap[5] == 0))
                        iap = fec_mac_default;
                if ((iap[0] == 0xff) && (iap[1] == 0xff) && (iap[2] == 0xff) &&
                    (iap[3] == 0xff) && (iap[4] == 0xff) && (iap[5] == 0xff))
                        iap = fec_mac_default;
        } else {
                *((unsigned long *) &tmpaddr[0]) = fecp->fec_addr_low;
                *((unsigned short *) &tmpaddr[4]) = (fecp->fec_addr_high >> 16);
                iap = &tmpaddr[0];
        }

        memcpy(dev->dev_addr, iap, ETH_ALEN);

        /* Adjust MAC if using default MAC address */
        if (iap == fec_mac_default)
                dev->dev_addr[ETH_ALEN-1] = fec_mac_default[ETH_ALEN-1] + fep->index;
}

static void __inline__ fec_enable_phy_intr(void)
{
}

static void __inline__ fec_disable_phy_intr(void)
{
}

static void __inline__ fec_phy_ack_intr(void)
{
}

static void __inline__ fec_localhw_setup(void)
{
}

/*
 *      Do not need to make region uncached on 532x.
 */
static void __inline__ fec_uncache(unsigned long addr)
{
}

/* ------------------------------------------------------------------------- */


#else

/*
 *      Code specific to the MPC860T setup.
 */
static void __inline__ fec_request_intrs(struct net_device *dev)
{
        volatile immap_t *immap;

        immap = (immap_t *)IMAP_ADDR;   /* pointer to internal registers */

        if (request_8xxirq(FEC_INTERRUPT, fec_enet_interrupt, 0, "fec", dev) != 0)
                panic("Could not allocate FEC IRQ!");

#ifdef CONFIG_RPXCLASSIC
        /* Make Port C, bit 15 an input that causes interrupts.
        */
        immap->im_ioport.iop_pcpar &= ~0x0001;
        immap->im_ioport.iop_pcdir &= ~0x0001;
        immap->im_ioport.iop_pcso &= ~0x0001;
        immap->im_ioport.iop_pcint |= 0x0001;
        cpm_install_handler(CPMVEC_PIO_PC15, mii_link_interrupt, dev);

        /* Make LEDS reflect Link status.
        */
        *((uint *) RPX_CSR_ADDR) &= ~BCSR2_FETHLEDMODE;
#endif
#ifdef CONFIG_FADS
        if (request_8xxirq(SIU_IRQ2, mii_link_interrupt, 0, "mii", dev) != 0)
                panic("Could not allocate MII IRQ!");
#endif
}

static void __inline__ fec_get_mac(struct net_device *dev)
{
        bd_t *bd;

        bd = (bd_t *)__res;
        memcpy(dev->dev_addr, bd->bi_enetaddr, ETH_ALEN);

#ifdef CONFIG_RPXCLASSIC
        /* The Embedded Planet boards have only one MAC address in
         * the EEPROM, but can have two Ethernet ports.  For the
         * FEC port, we create another address by setting one of
         * the address bits above something that would have (up to
         * now) been allocated.
         */
        dev->dev_adrd[3] |= 0x80;
#endif
}

static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
{
        extern uint _get_IMMR(void);
        volatile immap_t *immap;
        volatile fec_t *fecp;

        fecp = fep->hwp;
        immap = (immap_t *)IMAP_ADDR;   /* pointer to internal registers */

        /* Configure all of port D for MII.
        */
        immap->im_ioport.iop_pdpar = 0x1fff;

        /* Bits moved from Rev. D onward.
        */
        if ((_get_IMMR() & 0xffff) < 0x0501)
                immap->im_ioport.iop_pddir = 0x1c58;    /* Pre rev. D */
        else
                immap->im_ioport.iop_pddir = 0x1fff;    /* Rev. D and later */

        /* Set MII speed to 2.5 MHz
        */
        fecp->fec_mii_speed = fep->phy_speed =
                ((bd->bi_busfreq * 1000000) / 2500000) & 0x7e;
}

static void __inline__ fec_enable_phy_intr(void)
{
        volatile fec_t *fecp;

        fecp = fep->hwp;

        /* Enable MII command finished interrupt
        */
        fecp->fec_ivec = (FEC_INTERRUPT/2) << 29;
}

static void __inline__ fec_disable_phy_intr(void)
{
}

static void __inline__ fec_phy_ack_intr(void)
{
}

static void __inline__ fec_localhw_setup(void)
{
        volatile fec_t *fecp;

        fecp = fep->hwp;
        fecp->fec_r_hash = PKT_MAXBUF_SIZE;
        /* Enable big endian and don't care about SDMA FC.
        */
        fecp->fec_fun_code = 0x78000000;
}

static void __inline__ fec_uncache(unsigned long addr)
{
        pte_t *pte;
        pte = va_to_pte(mem_addr);
        pte_val(*pte) |= _PAGE_NO_CACHE;
        flush_tlb_page(init_mm.mmap, mem_addr);
}

#endif

/* ------------------------------------------------------------------------- */

static void mii_display_status(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        volatile uint *s = &(fep->phy_status);

        if (!fep->link && !fep->old_link) {
                /* Link is still down - don't print anything */
                return;
        }

        printk("%s: status: ", dev->name);

        if (!fep->link) {
                printk("link down");
        } else {
                printk("link up");

                switch(*s & PHY_STAT_SPMASK) {
                case PHY_STAT_100FDX: printk(", 100MBit Full Duplex"); break;
                case PHY_STAT_100HDX: printk(", 100MBit Half Duplex"); break;
                case PHY_STAT_10FDX: printk(", 10MBit Full Duplex"); break;
                case PHY_STAT_10HDX: printk(", 10MBit Half Duplex"); break;
                default:
                        printk(", Unknown speed/duplex");
                }

                if (*s & PHY_STAT_ANC)
                        printk(", auto-negotiation complete");
        }

        if (*s & PHY_STAT_FAULT)
                printk(", remote fault");

        printk(".\n");
}

static void mii_display_config(struct work_struct *work)
{
        struct fec_enet_private *fep = container_of(work, struct fec_enet_private, phy_task);
        struct net_device *dev = fep->netdev;
        uint status = fep->phy_status;

        /*
        ** When we get here, phy_task is already removed from
        ** the workqueue.  It is thus safe to allow to reuse it.
        */
        fep->mii_phy_task_queued = 0;
        printk("%s: config: auto-negotiation ", dev->name);

        if (status & PHY_CONF_ANE)
                printk("on");
        else
                printk("off");

        if (status & PHY_CONF_100FDX)
                printk(", 100FDX");
        if (status & PHY_CONF_100HDX)
                printk(", 100HDX");
        if (status & PHY_CONF_10FDX)
                printk(", 10FDX");
        if (status & PHY_CONF_10HDX)
                printk(", 10HDX");
        if (!(status & PHY_CONF_SPMASK))
                printk(", No speed/duplex selected?");

        if (status & PHY_CONF_LOOP)
                printk(", loopback enabled");

        printk(".\n");

        fep->sequence_done = 1;
}

static void mii_relink(struct work_struct *work)
{
        struct fec_enet_private *fep = container_of(work, struct fec_enet_private, phy_task);
        struct net_device *dev = fep->netdev;
        int duplex;

        /*
        ** When we get here, phy_task is already removed from
        ** the workqueue.  It is thus safe to allow to reuse it.
        */
        fep->mii_phy_task_queued = 0;
        fep->link = (fep->phy_status & PHY_STAT_LINK) ? 1 : 0;
        mii_display_status(dev);
        fep->old_link = fep->link;

        if (fep->link) {
                duplex = 0;
                if (fep->phy_status
                    & (PHY_STAT_100FDX | PHY_STAT_10FDX))
                        duplex = 1;
                fec_restart(dev, duplex);
        }
        else
                fec_stop(dev);

#if 0
        enable_irq(fep->mii_irq);
#endif

}

/* mii_queue_relink is called in interrupt context from mii_link_interrupt */
static void mii_queue_relink(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);

        /*
        ** We cannot queue phy_task twice in the workqueue.  It
        ** would cause an endless loop in the workqueue.
        ** Fortunately, if the last mii_relink entry has not yet been
        ** executed now, it will do the job for the current interrupt,
        ** which is just what we want.
        */
        if (fep->mii_phy_task_queued)
                return;

        fep->mii_phy_task_queued = 1;
        INIT_WORK(&fep->phy_task, mii_relink);
        schedule_work(&fep->phy_task);
}

/* mii_queue_config is called in interrupt context from fec_enet_mii */
static void mii_queue_config(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);

        if (fep->mii_phy_task_queued)
                return;

        fep->mii_phy_task_queued = 1;
        INIT_WORK(&fep->phy_task, mii_display_config);
        schedule_work(&fep->phy_task);
}

phy_cmd_t const phy_cmd_relink[] = {
        { mk_mii_read(MII_REG_CR), mii_queue_relink },
        { mk_mii_end, }
        };
phy_cmd_t const phy_cmd_config[] = {
        { mk_mii_read(MII_REG_CR), mii_queue_config },
        { mk_mii_end, }
        };

/* Read remainder of PHY ID.
*/
static void
mii_discover_phy3(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep;
        int i;

        fep = netdev_priv(dev);
        fep->phy_id |= (mii_reg & 0xffff);
        printk("fec: PHY @ 0x%x, ID 0x%08x", fep->phy_addr, fep->phy_id);

        for(i = 0; phy_info[i]; i++) {
                if(phy_info[i]->id == (fep->phy_id >> 4))
                        break;
        }

        if (phy_info[i])
                printk(" -- %s\n", phy_info[i]->name);
        else
                printk(" -- unknown PHY!\n");

        fep->phy = phy_info[i];
        fep->phy_id_done = 1;
}

/* Scan all of the MII PHY addresses looking for someone to respond
 * with a valid ID.  This usually happens quickly.
 */
static void
mii_discover_phy(uint mii_reg, struct net_device *dev)
{
        struct fec_enet_private *fep;
        volatile fec_t *fecp;
        uint phytype;

        fep = netdev_priv(dev);
        fecp = fep->hwp;

        if (fep->phy_addr < 32) {
                if ((phytype = (mii_reg & 0xffff)) != 0xffff && phytype != 0) {

                        /* Got first part of ID, now get remainder.
                        */
                        fep->phy_id = phytype << 16;
                        mii_queue(dev, mk_mii_read(MII_REG_PHYIR2),
                                                        mii_discover_phy3);
                }
                else {
                        fep->phy_addr++;
                        mii_queue(dev, mk_mii_read(MII_REG_PHYIR1),
                                                        mii_discover_phy);
                }
        } else {
                printk("FEC: No PHY device found.\n");
                /* Disable external MII interface */
                fecp->fec_mii_speed = fep->phy_speed = 0;
                fec_disable_phy_intr();
        }
}

/* This interrupt occurs when the PHY detects a link change.
*/
#ifdef CONFIG_RPXCLASSIC
static void
mii_link_interrupt(void *dev_id)
#else
static irqreturn_t
mii_link_interrupt(int irq, void * dev_id)
#endif
{
        struct  net_device *dev = dev_id;
        struct fec_enet_private *fep = netdev_priv(dev);

        fec_phy_ack_intr();

#if 0
        disable_irq(fep->mii_irq);  /* disable now, enable later */
#endif

        mii_do_cmd(dev, fep->phy->ack_int);
        mii_do_cmd(dev, phy_cmd_relink);  /* restart and display status */

        return IRQ_HANDLED;
}

static int
fec_enet_open(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);

        /* I should reset the ring buffers here, but I don't yet know
         * a simple way to do that.
         */
        fec_set_mac_address(dev);

        fep->sequence_done = 0;
        fep->link = 0;

        if (fep->phy) {
                mii_do_cmd(dev, fep->phy->ack_int);
                mii_do_cmd(dev, fep->phy->config);
                mii_do_cmd(dev, phy_cmd_config);  /* display configuration */

                /* Poll until the PHY tells us its configuration
                 * (not link state).
                 * Request is initiated by mii_do_cmd above, but answer
                 * comes by interrupt.
                 * This should take about 25 usec per register at 2.5 MHz,
                 * and we read approximately 5 registers.
                 */
                while(!fep->sequence_done)
                        schedule();

                mii_do_cmd(dev, fep->phy->startup);

                /* Set the initial link state to true. A lot of hardware
                 * based on this device does not implement a PHY interrupt,
                 * so we are never notified of link change.
                 */
                fep->link = 1;
        } else {
                fep->link = 1; /* lets just try it and see */
                /* no phy,  go full duplex,  it's most likely a hub chip */
                fec_restart(dev, 1);
        }

        netif_start_queue(dev);
        fep->opened = 1;
        return 0;               /* Success */
}

static int
fec_enet_close(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);

        /* Don't know what to do yet.
        */
        fep->opened = 0;
        netif_stop_queue(dev);
        fec_stop(dev);

        return 0;
}

static struct net_device_stats *fec_enet_get_stats(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);

        return &fep->stats;
}

/* Set or clear the multicast filter for this adaptor.
 * Skeleton taken from sunlance driver.
 * The CPM Ethernet implementation allows Multicast as well as individual
 * MAC address filtering.  Some of the drivers check to make sure it is
 * a group multicast address, and discard those that are not.  I guess I
 * will do the same for now, but just remove the test if you want
 * individual filtering as well (do the upper net layers want or support
 * this kind of feature?).
 */

#define HASH_BITS       6               /* #bits in hash */
#define CRC32_POLY      0xEDB88320

static void set_multicast_list(struct net_device *dev)
{
        struct fec_enet_private *fep;
        volatile fec_t *ep;
        struct dev_mc_list *dmi;
        unsigned int i, j, bit, data, crc;
        unsigned char hash;

        fep = netdev_priv(dev);
        ep = fep->hwp;

        if (dev->flags&IFF_PROMISC) {
                ep->fec_r_cntrl |= 0x0008;
        } else {

                ep->fec_r_cntrl &= ~0x0008;

                if (dev->flags & IFF_ALLMULTI) {
                        /* Catch all multicast addresses, so set the
                         * filter to all 1's.
                         */
                        ep->fec_hash_table_high = 0xffffffff;
                        ep->fec_hash_table_low = 0xffffffff;
                } else {
                        /* Clear filter and add the addresses in hash register.
                        */
                        ep->fec_hash_table_high = 0;
                        ep->fec_hash_table_low = 0;

                        dmi = dev->mc_list;

                        for (j = 0; j < dev->mc_count; j++, dmi = dmi->next)
                        {
                                /* Only support group multicast for now.
                                */
                                if (!(dmi->dmi_addr[0] & 1))
                                        continue;

                                /* calculate crc32 value of mac address
                                */
                                crc = 0xffffffff;

                                for (i = 0; i < dmi->dmi_addrlen; i++)
                                {
                                        data = dmi->dmi_addr[i];
                                        for (bit = 0; bit < 8; bit++, data >>= 1)
                                        {
                                                crc = (crc >> 1) ^
                                                (((crc ^ data) & 1) ? CRC32_POLY : 0);
                                        }
                                }

                                /* only upper 6 bits (HASH_BITS) are used
                                   which point to specific bit in he hash registers
                                */
                                hash = (crc >> (32 - HASH_BITS)) & 0x3f;

                                if (hash > 31)
                                        ep->fec_hash_table_high |= 1 << (hash - 32);
                                else
                                        ep->fec_hash_table_low |= 1 << hash;
                        }
                }
        }
}

/* Set a MAC change in hardware.
 */
static void
fec_set_mac_address(struct net_device *dev)
{
        volatile fec_t *fecp;

        fecp = ((struct fec_enet_private *)netdev_priv(dev))->hwp;

        /* Set station address. */
        fecp->fec_addr_low = dev->dev_addr[3] | (dev->dev_addr[2] << 8) |
                (dev->dev_addr[1] << 16) | (dev->dev_addr[0] << 24);
        fecp->fec_addr_high = (dev->dev_addr[5] << 16) |
                (dev->dev_addr[4] << 24);

}

/* Initialize the FEC Ethernet on 860T (or ColdFire 5272).
 */
 /*
  * XXX:  We need to clean up on failure exits here.
  */
int __init fec_enet_init(struct net_device *dev)
{
        struct fec_enet_private *fep = netdev_priv(dev);
        unsigned long   mem_addr;
        volatile cbd_t  *bdp;
        cbd_t           *cbd_base;
        volatile fec_t  *fecp;
        int             i, j;
        static int      index = 0;

        /* Only allow us to be probed once. */
        if (index >= FEC_MAX_PORTS)
                return -ENXIO;

        /* Allocate memory for buffer descriptors.
        */
        mem_addr = __get_free_page(GFP_KERNEL);
        if (mem_addr == 0) {
                printk("FEC: allocate descriptor memory failed?\n");
                return -ENOMEM;
        }

        /* Create an Ethernet device instance.
        */
        fecp = (volatile fec_t *) fec_hw[index];

        fep->index = index;
        fep->hwp = fecp;
        fep->netdev = dev;

        /* Whack a reset.  We should wait for this.
        */
        fecp->fec_ecntrl = 1;
        udelay(10);

        /* Set the Ethernet address.  If using multiple Enets on the 8xx,
         * this needs some work to get unique addresses.
         *
         * This is our default MAC address unless the user changes
         * it via eth_mac_addr (our dev->set_mac_addr handler).
         */
        fec_get_mac(dev);

        cbd_base = (cbd_t *)mem_addr;
        /* XXX: missing check for allocation failure */

        fec_uncache(mem_addr);

        /* Set receive and transmit descriptor base.
        */
        fep->rx_bd_base = cbd_base;
        fep->tx_bd_base = cbd_base + RX_RING_SIZE;

        fep->dirty_tx = fep->cur_tx = fep->tx_bd_base;
        fep->cur_rx = fep->rx_bd_base;

        fep->skb_cur = fep->skb_dirty = 0;

        /* Initialize the receive buffer descriptors.
        */
        bdp = fep->rx_bd_base;
        for (i=0; i<FEC_ENET_RX_PAGES; i++) {

                /* Allocate a page.
                */
                mem_addr = __get_free_page(GFP_KERNEL);
                /* XXX: missing check for allocation failure */

                fec_uncache(mem_addr);

                /* Initialize the BD for every fragment in the page.
                */
                for (j=0; j<FEC_ENET_RX_FRPPG; j++) {
                        bdp->cbd_sc = BD_ENET_RX_EMPTY;
                        bdp->cbd_bufaddr = __pa(mem_addr);
                        mem_addr += FEC_ENET_RX_FRSIZE;
                        bdp++;
                }
        }

        /* Set the last buffer to wrap.
        */
        bdp--;
        bdp->cbd_sc |= BD_SC_WRAP;

        /* ...and the same for transmmit.
        */
        bdp = fep->tx_bd_base;
        for (i=0, j=FEC_ENET_TX_FRPPG; i<TX_RING_SIZE; i++) {
                if (j >= FEC_ENET_TX_FRPPG) {
                        mem_addr = __get_free_page(GFP_KERNEL);
                        j = 1;
                } else {
                        mem_addr += FEC_ENET_TX_FRSIZE;
                        j++;
                }
                fep->tx_bounce[i] = (unsigned char *) mem_addr;

                /* Initialize the BD for every fragment in the page.
                */
                bdp->cbd_sc = 0;
                bdp->cbd_bufaddr = 0;
                bdp++;
        }

        /* Set the last buffer to wrap.
        */
        bdp--;
        bdp->cbd_sc |= BD_SC_WRAP;

        /* Set receive and transmit descriptor base.
        */
        fecp->fec_r_des_start = __pa((uint)(fep->rx_bd_base));
        fecp->fec_x_des_start = __pa((uint)(fep->tx_bd_base));

        /* Install our interrupt handlers. This varies depending on
         * the architecture.
        */
        fec_request_intrs(dev);

        fecp->fec_hash_table_high = 0;
        fecp->fec_hash_table_low = 0;
        fecp->fec_r_buff_size = PKT_MAXBLR_SIZE;
        fecp->fec_ecntrl = 2;
        fecp->fec_r_des_active = 0;

        dev->base_addr = (unsigned long)fecp;

        /* The FEC Ethernet specific entries in the device structure. */
        dev->open = fec_enet_open;
        dev->hard_start_xmit = fec_enet_start_xmit;
        dev->tx_timeout = fec_timeout;
        dev->watchdog_timeo = TX_TIMEOUT;
        dev->stop = fec_enet_close;
        dev->get_stats = fec_enet_get_stats;
        dev->set_multicast_list = set_multicast_list;

        for (i=0; i<NMII-1; i++)
                mii_cmds[i].mii_next = &mii_cmds[i+1];
        mii_free = mii_cmds;

        /* setup MII interface */
        fec_set_mii(dev, fep);

        /* Clear and enable interrupts */
        fecp->fec_ievent = 0xffc00000;
        fecp->fec_imask = (FEC_ENET_TXF | FEC_ENET_TXB |
                FEC_ENET_RXF | FEC_ENET_RXB | FEC_ENET_MII);

        /* Queue up command to detect the PHY and initialize the
         * remainder of the interface.
         */
        fep->phy_id_done = 0;
        fep->phy_addr = 0;
        mii_queue(dev, mk_mii_read(MII_REG_PHYIR1), mii_discover_phy);

        index++;
        return 0;
}

/* This function is called to start or restart the FEC during a link
 * change.  This only happens when switching between half and full
 * duplex.
 */
static void
fec_restart(struct net_device *dev, int duplex)
{
        struct fec_enet_private *fep;
        volatile cbd_t *bdp;
        volatile fec_t *fecp;
        int i;

        fep = netdev_priv(dev);
        fecp = fep->hwp;

        /* Whack a reset.  We should wait for this.
        */
        fecp->fec_ecntrl = 1;
        udelay(10);

        /* Clear any outstanding interrupt.
        */
        fecp->fec_ievent = 0xffc00000;
        fec_enable_phy_intr();

        /* Set station address.
        */
        fec_set_mac_address(dev);

        /* Reset all multicast.
        */
        fecp->fec_hash_table_high = 0;
        fecp->fec_hash_table_low = 0;

        /* Set maximum receive buffer size.
        */
        fecp->fec_r_buff_size = PKT_MAXBLR_SIZE;

        fec_localhw_setup();

        /* Set receive and transmit descriptor base.
        */
        fecp->fec_r_des_start = __pa((uint)(fep->rx_bd_base));
        fecp->fec_x_des_start = __pa((uint)(fep->tx_bd_base));

        fep->dirty_tx = fep->cur_tx = fep->tx_bd_base;
        fep->cur_rx = fep->rx_bd_base;

        /* Reset SKB transmit buffers.
        */
        fep->skb_cur = fep->skb_dirty = 0;
        for (i=0; i<=TX_RING_MOD_MASK; i++) {
                if (fep->tx_skbuff[i] != NULL) {
                        dev_kfree_skb_any(fep->tx_skbuff[i]);
                        fep->tx_skbuff[i] = NULL;
                }
        }

        /* Initialize the receive buffer descriptors.
        */
        bdp = fep->rx_bd_base;
        for (i=0; i<RX_RING_SIZE; i++) {

                /* Initialize the BD for every fragment in the page.
                */
                bdp->cbd_sc = BD_ENET_RX_EMPTY;
                bdp++;
        }

        /* Set the last buffer to wrap.
        */
        bdp--;
        bdp->cbd_sc |= BD_SC_WRAP;

        /* ...and the same for transmmit.
        */
        bdp = fep->tx_bd_base;
        for (i=0; i<TX_RING_SIZE; i++) {

                /* Initialize the BD for every fragment in the page.
                */
                bdp->cbd_sc = 0;
                bdp->cbd_bufaddr = 0;
                bdp++;
        }

        /* Set the last buffer to wrap.
        */
        bdp--;
        bdp->cbd_sc |= BD_SC_WRAP;

        /* Enable MII mode.
        */
        if (duplex) {
                fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x04;/* MII enable */
                fecp->fec_x_cntrl = 0x04;                 /* FD enable */
        }
        else {
                /* MII enable|No Rcv on Xmit */
                fecp->fec_r_cntrl = OPT_FRAME_SIZE | 0x06;
                fecp->fec_x_cntrl = 0x00;
        }
        fep->full_duplex = duplex;

        /* Set MII speed.
        */
        fecp->fec_mii_speed = fep->phy_speed;

        /* And last, enable the transmit and receive processing.
        */
        fecp->fec_ecntrl = 2;
        fecp->fec_r_des_active = 0;

        /* Enable interrupts we wish to service.
        */
        fecp->fec_imask = (FEC_ENET_TXF | FEC_ENET_TXB |
                FEC_ENET_RXF | FEC_ENET_RXB | FEC_ENET_MII);
}

static void
fec_stop(struct net_device *dev)
{
        volatile fec_t *fecp;
        struct fec_enet_private *fep;

        fep = netdev_priv(dev);
        fecp = fep->hwp;

        /*
        ** We cannot expect a graceful transmit stop without link !!!
        */
        if (fep->link)
                {
                fecp->fec_x_cntrl = 0x01;       /* Graceful transmit stop */
                udelay(10);
                if (!(fecp->fec_ievent & FEC_ENET_GRA))
                        printk("fec_stop : Graceful transmit stop did not complete !\n");
                }

        /* Whack a reset.  We should wait for this.
        */
        fecp->fec_ecntrl = 1;
        udelay(10);

        /* Clear outstanding MII command interrupts.
        */
        fecp->fec_ievent = FEC_ENET_MII;
        fec_enable_phy_intr();

        fecp->fec_imask = FEC_ENET_MII;
        fecp->fec_mii_speed = fep->phy_speed;
}

static int __init fec_enet_module_init(void)
{
        struct net_device *dev;
        int i, j, err;

        printk("FEC ENET Version 0.2\n");

        for (i = 0; (i < FEC_MAX_PORTS); i++) {
                dev = alloc_etherdev(sizeof(struct fec_enet_private));
                if (!dev)
                        return -ENOMEM;
                err = fec_enet_init(dev);
                if (err) {
                        free_netdev(dev);
                        continue;
                }
                if (register_netdev(dev) != 0) {
                        /* XXX: missing cleanup here */
                        free_netdev(dev);
                        return -EIO;
                }

                printk("%s: ethernet ", dev->name);
                for (j = 0; (j < 5); j++)
                        printk("%02x:", dev->dev_addr[j]);
                printk("%02x\n", dev->dev_addr[5]);
        }
        return 0;
}

module_init(fec_enet_module_init);

MODULE_LICENSE("GPL");