arch/all-pc/boot/grub/netboot/smc9000.h

   1 /*------------------------------------------------------------------------
   2  * smc9000.h
   3  *
   4  * Copyright (C) 1998 by Daniel Engström
   5  * Copyright (C) 1996 by Erik Stahlman
   6  *
   7  * This software may be used and distributed according to the terms
   8  * of the GNU Public License, incorporated herein by reference.
   9  *
  10  * This file contains register information and access macros for
  11  * the SMC91xxx chipset.
  12  *
  13  * Information contained in this file was obtained from the SMC91C94
  14  * manual from SMC.  To get a copy, if you really want one, you can find
  15  * information under www.smsc.com in the components division.
  16  * ( this thanks to advice from Donald Becker ).
  17  *
  18  * Authors
  19  *      Daniel Engström                         <daniel.engstrom@riksnett.no>
  20  *      Erik Stahlman                           <erik@vt.edu>
  21  *
  22  * History
  23  * 96-01-06              Erik Stahlman   moved definitions here from main .c
  24  *                                       file
  25  * 96-01-19              Erik Stahlman   polished this up some, and added
  26  *                                       better error handling
  27  * 98-09-25              Daniel Engström adjusted for Etherboot
  28  * 98-09-27              Daniel Engström moved some static strings back to the
  29  *                                       main .c file
  30  * --------------------------------------------------------------------------*/
  31 #ifndef _SMC9000_H_
  32 # define _SMC9000_H_
  33
  34 /* I want some simple types */
  35 typedef unsigned char                   byte;
  36 typedef unsigned short                  word;
  37 typedef unsigned long int               dword;
  38
  39 /*---------------------------------------------------------------
  40  *
  41  * A description of the SMC registers is probably in order here,
  42  * although for details, the SMC datasheet is invaluable.
  43  *
  44  * Basically, the chip has 4 banks of registers ( 0 to 3 ), which
  45  * are accessed by writing a number into the BANK_SELECT register
  46  * ( I also use a SMC_SELECT_BANK macro for this ).
  47  *
  48  * The banks are configured so that for most purposes, bank 2 is all
  49  * that is needed for simple run time tasks.
  50  * ----------------------------------------------------------------------*/
  51
  52 /*
  53  * Bank Select Register:
  54  *
  55  *              yyyy yyyy 0000 00xx
  56  *              xx              = bank number
  57  *              yyyy yyyy       = 0x33, for identification purposes.
  58  */
  59 #define BANK_SELECT             14
  60
  61 /* BANK 0  */
  62
  63 #define TCR             0       /* transmit control register */
  64 #define TCR_ENABLE      0x0001  /* if this is 1, we can transmit */
  65 #define TCR_FDUPLX      0x0800  /* receive packets sent out */
  66 #define TCR_STP_SQET    0x1000  /* stop transmitting if Signal quality error */
  67 #define TCR_MON_CNS     0x0400  /* monitors the carrier status */
  68 #define TCR_PAD_ENABLE  0x0080  /* pads short packets to 64 bytes */
  69
  70 #define TCR_CLEAR       0       /* do NOTHING */
  71 /* the normal settings for the TCR register : */
  72 #define TCR_NORMAL      (TCR_ENABLE | TCR_PAD_ENABLE)
  73
  74
  75 #define EPH_STATUS      2
  76 #define ES_LINK_OK      0x4000  /* is the link integrity ok ? */
  77
  78 #define RCR             4
  79 #define RCR_SOFTRESET   0x8000  /* resets the chip */
  80 #define RCR_STRIP_CRC   0x200   /* strips CRC */
  81 #define RCR_ENABLE      0x100   /* IFF this is set, we can receive packets */
  82 #define RCR_ALMUL       0x4     /* receive all multicast packets */
  83 #define RCR_PROMISC     0x2     /* enable promiscuous mode */
  84
  85 /* the normal settings for the RCR register : */
  86 #define RCR_NORMAL      (RCR_STRIP_CRC | RCR_ENABLE)
  87 #define RCR_CLEAR       0x0             /* set it to a base state */
  88
  89 #define COUNTER         6
  90 #define MIR             8
  91 #define MCR             10
  92 /* 12 is reserved */
  93
  94 /* BANK 1 */
  95 #define CONFIG                  0
  96 #define CFG_AUI_SELECT          0x100
  97 #define BASE                    2
  98 #define ADDR0                   4
  99 #define ADDR1                   6
 100 #define ADDR2                   8
 101 #define GENERAL                 10
 102 #define CONTROL                 12
 103 #define CTL_POWERDOWN           0x2000
 104 #define CTL_LE_ENABLE           0x80
 105 #define CTL_CR_ENABLE           0x40
 106 #define CTL_TE_ENABLE           0x0020
 107 #define CTL_AUTO_RELEASE        0x0800
 108 #define CTL_EPROM_ACCESS        0x0003 /* high if Eprom is being read */
 109
 110 /* BANK 2 */
 111 #define MMU_CMD         0
 112 #define MC_BUSY         1       /* only readable bit in the register */
 113 #define MC_NOP          0
 114 #define MC_ALLOC        0x20    /* or with number of 256 byte packets */
 115 #define MC_RESET        0x40
 116 #define MC_REMOVE       0x60    /* remove the current rx packet */
 117 #define MC_RELEASE      0x80    /* remove and release the current rx packet */
 118 #define MC_FREEPKT      0xA0    /* Release packet in PNR register */
 119 #define MC_ENQUEUE      0xC0    /* Enqueue the packet for transmit */
 120
 121 #define PNR_ARR         2
 122 #define FIFO_PORTS      4
 123
 124 #define FP_RXEMPTY      0x8000
 125 #define FP_TXEMPTY      0x80
 126
 127 #define POINTER         6
 128 #define PTR_READ        0x2000
 129 #define PTR_RCV         0x8000
 130 #define PTR_AUTOINC     0x4000
 131 #define PTR_AUTO_INC    0x0040
 132
 133 #define DATA_1          8
 134 #define DATA_2          10
 135 #define INTERRUPT       12
 136
 137 #define INT_MASK        13
 138 #define IM_RCV_INT      0x1
 139 #define IM_TX_INT       0x2
 140 #define IM_TX_EMPTY_INT 0x4
 141 #define IM_ALLOC_INT    0x8
 142 #define IM_RX_OVRN_INT  0x10
 143 #define IM_EPH_INT      0x20
 144 #define IM_ERCV_INT     0x40 /* not on SMC9192 */
 145
 146 /* BANK 3 */
 147 #define MULTICAST1      0
 148 #define MULTICAST2      2
 149 #define MULTICAST3      4
 150 #define MULTICAST4      6
 151 #define MGMT            8
 152 #define REVISION        10 /* ( hi: chip id   low: rev # ) */
 153
 154
 155 /* this is NOT on SMC9192 */
 156 #define ERCV            12
 157
 158 /* Note that 9194 and 9196 have the smame chip id,
 159  * the 9196 will have revisions starting at 6 */
 160 #define CHIP_9190       3
 161 #define CHIP_9194       4
 162 #define CHIP_9195       5
 163 #define CHIP_9196       4
 164 #define CHIP_91100      7
 165 #define CHIP_91100FD    8
 166
 167 #define REV_9196        6
 168
 169 /*
 170  * Transmit status bits
 171  */
 172 #define TS_SUCCESS      0x0001
 173 #define TS_LOSTCAR      0x0400
 174 #define TS_LATCOL       0x0200
 175 #define TS_16COL        0x0010
 176
 177 /*
 178  * Receive status bits
 179  */
 180 #define RS_ALGNERR      0x8000
 181 #define RS_BADCRC       0x2000
 182 #define RS_ODDFRAME     0x1000
 183 #define RS_TOOLONG      0x0800
 184 #define RS_TOOSHORT     0x0400
 185 #define RS_MULTICAST    0x0001
 186 #define RS_ERRORS       (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT)
 187
 188
 189 /*-------------------------------------------------------------------------
 190  *  I define some macros to make it easier to do somewhat common
 191  * or slightly complicated, repeated tasks.
 192  --------------------------------------------------------------------------*/
 193
 194 /* select a register bank, 0 to 3  */
 195
 196 #define SMC_SELECT_BANK(x, y) { _outw( y, x + BANK_SELECT ); }
 197
 198 /* define a small delay for the reset */
 199 #define SMC_DELAY(x) { inw( x + RCR );\
 200                         inw( x + RCR );\
 201                         inw( x + RCR ); }
 202
 203
 204 #endif  /* _SMC_9000_H_ */
 205