drivers/scsi/aha152x.h

   1 #ifndef _AHA152X_H
   2 #define _AHA152X_H
   3
   4 /*
   5  * $Id: aha152x.h,v 2.7 2004/01/24 11:39:03 fischer Exp $
   6  */
   7
   8 /* number of queueable commands
   9    (unless we support more than 1 cmd_per_lun this should do) */
  10 #define AHA152X_MAXQUEUE 7
  11
  12 #define AHA152X_REVID "Adaptec 152x SCSI driver; $Revision: 2.7 $"
  13
  14 /* port addresses */
  15 #define SCSISEQ      (HOSTIOPORT0+0x00)    /* SCSI sequence control */
  16 #define SXFRCTL0     (HOSTIOPORT0+0x01)    /* SCSI transfer control 0 */
  17 #define SXFRCTL1     (HOSTIOPORT0+0x02)    /* SCSI transfer control 1 */
  18 #define SCSISIG      (HOSTIOPORT0+0x03)    /* SCSI signal in/out */
  19 #define SCSIRATE     (HOSTIOPORT0+0x04)    /* SCSI rate control */
  20 #define SELID        (HOSTIOPORT0+0x05)    /* selection/reselection ID */
  21 #define SCSIID       SELID                 /* SCSI ID */
  22 #define SCSIDAT      (HOSTIOPORT0+0x06)    /* SCSI latched data */
  23 #define SCSIBUS      (HOSTIOPORT0+0x07)    /* SCSI data bus */
  24 #define STCNT0       (HOSTIOPORT0+0x08)    /* SCSI transfer count 0 */
  25 #define STCNT1       (HOSTIOPORT0+0x09)    /* SCSI transfer count 1 */
  26 #define STCNT2       (HOSTIOPORT0+0x0a)    /* SCSI transfer count 2 */
  27 #define SSTAT0       (HOSTIOPORT0+0x0b)    /* SCSI interrupt status 0 */
  28 #define SSTAT1       (HOSTIOPORT0+0x0c)    /* SCSI interrupt status 1 */
  29 #define SSTAT2       (HOSTIOPORT0+0x0d)    /* SCSI interrupt status 2 */
  30 #define SCSITEST     (HOSTIOPORT0+0x0e)    /* SCSI test control */
  31 #define SSTAT3       SCSITEST              /* SCSI interrupt status 3 */
  32 #define SSTAT4       (HOSTIOPORT0+0x0f)    /* SCSI status 4 */
  33 #define SIMODE0      (HOSTIOPORT1+0x10)    /* SCSI interrupt mode 0 */
  34 #define SIMODE1      (HOSTIOPORT1+0x11)    /* SCSI interrupt mode 1 */
  35 #define DMACNTRL0    (HOSTIOPORT1+0x12)    /* DMA control 0 */
  36 #define DMACNTRL1    (HOSTIOPORT1+0x13)    /* DMA control 1 */
  37 #define DMASTAT      (HOSTIOPORT1+0x14)    /* DMA status */
  38 #define FIFOSTAT     (HOSTIOPORT1+0x15)    /* FIFO status */
  39 #define DATAPORT     (HOSTIOPORT1+0x16)    /* DATA port */
  40 #define BRSTCNTRL    (HOSTIOPORT1+0x18)    /* burst control */
  41 #define PORTA        (HOSTIOPORT1+0x1a)    /* PORT A */
  42 #define PORTB        (HOSTIOPORT1+0x1b)    /* PORT B */
  43 #define REV          (HOSTIOPORT1+0x1c)    /* revision */
  44 #define STACK        (HOSTIOPORT1+0x1d)    /* stack */
  45 #define TEST         (HOSTIOPORT1+0x1e)    /* test register */
  46
  47 #define IO_RANGE        0x20
  48
  49 /* used in aha152x_porttest */
  50 #define O_PORTA         0x1a               /* PORT A */
  51 #define O_PORTB         0x1b               /* PORT B */
  52 #define O_DMACNTRL1     0x13               /* DMA control 1 */
  53 #define O_STACK         0x1d               /* stack */
  54
  55 /* used in tc1550_porttest */
  56 #define O_TC_PORTA      0x0a               /* PORT A */
  57 #define O_TC_PORTB      0x0b               /* PORT B */
  58 #define O_TC_DMACNTRL1  0x03               /* DMA control 1 */
  59 #define O_TC_STACK      0x0d               /* stack */
  60
  61 /* bits and bitmasks to ports */
  62
  63 /* SCSI sequence control */
  64 #define TEMODEO      0x80
  65 #define ENSELO       0x40
  66 #define ENSELI       0x20
  67 #define ENRESELI     0x10
  68 #define ENAUTOATNO   0x08
  69 #define ENAUTOATNI   0x04
  70 #define ENAUTOATNP   0x02
  71 #define SCSIRSTO     0x01
  72
  73 /* SCSI transfer control 0 */
  74 #define SCSIEN       0x80
  75 #define DMAEN        0x40
  76 #define CH1          0x20
  77 #define CLRSTCNT     0x10
  78 #define SPIOEN       0x08
  79 #define CLRCH1       0x02
  80
  81 /* SCSI transfer control 1 */
  82 #define BITBUCKET    0x80
  83 #define SWRAPEN      0x40
  84 #define ENSPCHK      0x20
  85 #define STIMESEL     0x18    /* mask */
  86 #define STIMESEL_    3
  87 #define ENSTIMER     0x04
  88 #define BYTEALIGN    0x02
  89
  90 /* SCSI signal IN */
  91 #define SIG_CDI          0x80
  92 #define SIG_IOI          0x40
  93 #define SIG_MSGI         0x20
  94 #define SIG_ATNI         0x10
  95 #define SIG_SELI         0x08
  96 #define SIG_BSYI         0x04
  97 #define SIG_REQI         0x02
  98 #define SIG_ACKI         0x01
  99
 100 /* SCSI Phases */
 101 #define P_MASK       (SIG_MSGI|SIG_CDI|SIG_IOI)
 102 #define P_DATAO      (0)
 103 #define P_DATAI      (SIG_IOI)
 104 #define P_CMD        (SIG_CDI)
 105 #define P_STATUS     (SIG_CDI|SIG_IOI)
 106 #define P_MSGO       (SIG_MSGI|SIG_CDI)
 107 #define P_MSGI       (SIG_MSGI|SIG_CDI|SIG_IOI)
 108
 109 /* SCSI signal OUT */
 110 #define SIG_CDO          0x80
 111 #define SIG_IOO          0x40
 112 #define SIG_MSGO         0x20
 113 #define SIG_ATNO         0x10
 114 #define SIG_SELO         0x08
 115 #define SIG_BSYO         0x04
 116 #define SIG_REQO         0x02
 117 #define SIG_ACKO         0x01
 118
 119 /* SCSI rate control */
 120 #define SXFR         0x70    /* mask */
 121 #define SXFR_        4
 122 #define SOFS         0x0f    /* mask */
 123
 124 /* SCSI ID */
 125 #define OID          0x70
 126 #define OID_         4
 127 #define TID          0x07
 128
 129 /* SCSI transfer count */
 130 #define GETSTCNT() ( (GETPORT(STCNT2)<<16) \
 131                    + (GETPORT(STCNT1)<< 8) \
 132                    + GETPORT(STCNT0) )
 133
 134 #define SETSTCNT(X) { SETPORT(STCNT2, ((X) & 0xFF0000) >> 16); \
 135                       SETPORT(STCNT1, ((X) & 0x00FF00) >>  8); \
 136                       SETPORT(STCNT0, ((X) & 0x0000FF) ); }
 137
 138 /* SCSI interrupt status */
 139 #define TARGET       0x80
 140 #define SELDO        0x40
 141 #define SELDI        0x20
 142 #define SELINGO      0x10
 143 #define SWRAP        0x08
 144 #define SDONE        0x04
 145 #define SPIORDY      0x02
 146 #define DMADONE      0x01
 147
 148 #define SETSDONE     0x80
 149 #define CLRSELDO     0x40
 150 #define CLRSELDI     0x20
 151 #define CLRSELINGO   0x10
 152 #define CLRSWRAP     0x08
 153 #define CLRSDONE     0x04
 154 #define CLRSPIORDY   0x02
 155 #define CLRDMADONE   0x01
 156
 157 /* SCSI status 1 */
 158 #define SELTO        0x80
 159 #define ATNTARG      0x40
 160 #define SCSIRSTI     0x20
 161 #define PHASEMIS     0x10
 162 #define BUSFREE      0x08
 163 #define SCSIPERR     0x04
 164 #define PHASECHG     0x02
 165 #define REQINIT      0x01
 166
 167 #define CLRSELTIMO   0x80
 168 #define CLRATNO      0x40
 169 #define CLRSCSIRSTI  0x20
 170 #define CLRBUSFREE   0x08
 171 #define CLRSCSIPERR  0x04
 172 #define CLRPHASECHG  0x02
 173 #define CLRREQINIT   0x01
 174
 175 /* SCSI status 2 */
 176 #define SOFFSET      0x20
 177 #define SEMPTY       0x10
 178 #define SFULL        0x08
 179 #define SFCNT        0x07    /* mask */
 180
 181 /* SCSI status 3 */
 182 #define SCSICNT      0xf0    /* mask */
 183 #define SCSICNT_     4
 184 #define OFFCNT       0x0f    /* mask */
 185
 186 /* SCSI TEST control */
 187 #define SCTESTU      0x08
 188 #define SCTESTD      0x04
 189 #define STCTEST      0x01
 190
 191 /* SCSI status 4 */
 192 #define SYNCERR      0x04
 193 #define FWERR        0x02
 194 #define FRERR        0x01
 195
 196 #define CLRSYNCERR   0x04
 197 #define CLRFWERR     0x02
 198 #define CLRFRERR     0x01
 199
 200 /* SCSI interrupt mode 0 */
 201 #define ENSELDO      0x40
 202 #define ENSELDI      0x20
 203 #define ENSELINGO    0x10
 204 #define ENSWRAP      0x08
 205 #define ENSDONE      0x04
 206 #define ENSPIORDY    0x02
 207 #define ENDMADONE    0x01
 208
 209 /* SCSI interrupt mode 1 */
 210 #define ENSELTIMO    0x80
 211 #define ENATNTARG    0x40
 212 #define ENSCSIRST    0x20
 213 #define ENPHASEMIS   0x10
 214 #define ENBUSFREE    0x08
 215 #define ENSCSIPERR   0x04
 216 #define ENPHASECHG   0x02
 217 #define ENREQINIT    0x01
 218
 219 /* DMA control 0 */
 220 #define ENDMA        0x80
 221 #define _8BIT        0x40
 222 #define DMA          0x20
 223 #define WRITE_READ   0x08
 224 #define INTEN        0x04
 225 #define RSTFIFO      0x02
 226 #define SWINT        0x01
 227
 228 /* DMA control 1 */
 229 #define PWRDWN       0x80
 230 #define STK          0x07    /* mask */
 231
 232 /* DMA status */
 233 #define ATDONE       0x80
 234 #define WORDRDY      0x40
 235 #define INTSTAT      0x20
 236 #define DFIFOFULL    0x10
 237 #define DFIFOEMP     0x08
 238
 239 /* BURST control */
 240 #define BON          0xf0
 241 #define BOFF         0x0f
 242
 243 /* TEST REGISTER */
 244 #define BOFFTMR      0x40
 245 #define BONTMR       0x20
 246 #define STCNTH       0x10
 247 #define STCNTM       0x08
 248 #define STCNTL       0x04
 249 #define SCSIBLK      0x02
 250 #define DMABLK       0x01
 251
 252 /* On the AHA-152x board PORTA and PORTB contain
 253    some information about the board's configuration. */
 254 typedef union {
 255   struct {
 256     unsigned reserved:2;    /* reserved */
 257     unsigned tardisc:1;     /* Target disconnect: 0=disabled, 1=enabled */
 258     unsigned syncneg:1;     /* Initial sync neg: 0=disabled, 1=enabled */
 259     unsigned msgclasses:2;  /* Message classes
 260                                  0=#4
 261                                  1=#0, #1, #2, #3, #4
 262                                  2=#0, #3, #4
 263                                  3=#0, #4
 264                              */
 265     unsigned boot:1;        /* boot: 0=disabled, 1=enabled */
 266     unsigned dma:1;         /* Transfer mode: 0=PIO; 1=DMA */
 267     unsigned id:3;          /* SCSI-id */
 268     unsigned irq:2;         /* IRQ-Channel: 0,3=12, 1=10, 2=11 */
 269     unsigned dmachan:2;     /* DMA-Channel: 0=0, 1=5, 2=6, 3=7 */
 270     unsigned parity:1;      /* SCSI-parity: 1=enabled 0=disabled */
 271   } fields;
 272   unsigned short port;
 273 } aha152x_config ;
 274
 275 #define cf_parity     fields.parity
 276 #define cf_dmachan    fields.dmachan
 277 #define cf_irq        fields.irq
 278 #define cf_id         fields.id
 279 #define cf_dma        fields.dma
 280 #define cf_boot       fields.boot
 281 #define cf_msgclasses fields.msgclasses
 282 #define cf_syncneg    fields.syncneg
 283 #define cf_tardisc    fields.tardisc
 284 #define cf_port       port
 285
 286 /* Some macros to manipulate ports and their bits */
 287
 288 #define SETPORT(PORT, VAL)      outb( (VAL), (PORT) )
 289 #define GETPORT(PORT)           inb( PORT )
 290 #define SETBITS(PORT, BITS)     outb( (inb(PORT) | (BITS)), (PORT) )
 291 #define CLRBITS(PORT, BITS)     outb( (inb(PORT) & ~(BITS)), (PORT) )
 292 #define TESTHI(PORT, BITS)      ((inb(PORT) & (BITS)) == (BITS))
 293 #define TESTLO(PORT, BITS)      ((inb(PORT) & (BITS)) == 0)
 294
 295 #define SETRATE(RATE)           SETPORT(SCSIRATE,(RATE) & 0x7f)
 296
 297 #if defined(AHA152X_DEBUG)
 298 enum {
 299   debug_procinfo  = 0x0001,
 300   debug_queue     = 0x0002,
 301   debug_locking   = 0x0004,
 302   debug_intr      = 0x0008,
 303   debug_selection = 0x0010,
 304   debug_msgo      = 0x0020,
 305   debug_msgi      = 0x0040,
 306   debug_status    = 0x0080,
 307   debug_cmd       = 0x0100,
 308   debug_datai     = 0x0200,
 309   debug_datao     = 0x0400,
 310   debug_eh        = 0x0800,
 311   debug_done      = 0x1000,
 312   debug_phases    = 0x2000,
 313 };
 314 #endif
 315
 316 /* for the pcmcia stub */
 317 struct aha152x_setup {
 318         int io_port;
 319         int irq;
 320         int scsiid;
 321         int reconnect;
 322         int parity;
 323         int synchronous;
 324         int delay;
 325         int ext_trans;
 326         int tc1550;
 327 #if defined(AHA152X_DEBUG)
 328         int debug;
 329 #endif
 330         char *conf;
 331 };
 332
 333 struct Scsi_Host *aha152x_probe_one(struct aha152x_setup *);
 334 void aha152x_release(struct Scsi_Host *);
 335 int aha152x_host_reset_host(struct Scsi_Host *);
 336
 337 #endif /* _AHA152X_H */