drivers/ipmi/ocp: Add missing include
[coreboot.git] / src / drivers / uart / oxpcie_early.c
blob7cc908cc37c5714159d70696e4437b9d36a55130
1 /* SPDX-License-Identifier: GPL-2.0-only */
3 #include <stdint.h>
4 #include <device/pci_ops.h>
5 #include <console/uart.h>
6 #include <device/pci.h>
7 #include "uart8250reg.h"
9 static int oxpcie_present;
10 static DEVTREE_CONST u32 uart0_base = CONFIG_EARLY_PCI_MMIO_BASE + 0x1000;
12 int pci_early_device_probe(u8 bus, u8 dev, u32 mmio_base)
14 pci_devfn_t device = PCI_DEV(bus, dev, 0);
16 u32 id = pci_s_read_config32(device, PCI_VENDOR_ID);
17 switch (id) {
18 case 0xc1181415: /* e.g. Startech PEX1S1PMINI function 0 */
19 /* On this device function 0 is the parallel port, and
20 * function 3 is the serial port. So let's go look for
21 * the UART.
23 device = PCI_DEV(bus, dev, 3);
24 id = pci_s_read_config32(device, PCI_VENDOR_ID);
25 if (id != 0xc11b1415)
26 return -1;
27 break;
28 case 0xc11b1415: /* e.g. Startech PEX1S1PMINI function 3 */
29 case 0xc1581415: /* e.g. Startech MPEX2S952 */
30 break;
31 default:
32 /* No UART here. */
33 return -1;
36 /* Sanity-check, we assume fixed location. */
37 if (mmio_base != CONFIG_EARLY_PCI_MMIO_BASE)
38 return -1;
40 /* Setup base address on device */
41 pci_s_write_config32(device, PCI_BASE_ADDRESS_0, mmio_base);
43 /* Enable memory on device */
44 u16 reg16 = pci_s_read_config16(device, PCI_COMMAND);
45 reg16 |= PCI_COMMAND_MEMORY;
46 pci_s_write_config16(device, PCI_COMMAND, reg16);
48 oxpcie_present = 1;
49 return 0;
53 * Stages that do not call pci_early_device_probe() identify an
54 * enabled UART with a test read. Since PCI bus enumeration
55 * has not happened PCI configuration register access is not
56 * possible here.
58 static int uart_presence(uintptr_t base)
60 /* LCR has no side-effects on reads. */
61 const u8 reg = UART8250_LCR;
62 u8 val;
64 if (CONFIG(DRIVERS_UART_8250MEM_32))
65 val = read32p(base + 4 * reg) & 0xff;
66 else
67 val = read8p(base + reg);
69 if (val == 0xff)
70 return -1;
72 /* Something decoded MMIO read, assume it was the UART. */
73 return 1;
76 static bool oxpcie_uart_active(void)
78 if (oxpcie_present == 0)
79 oxpcie_present = uart_presence(uart0_base);
81 if (oxpcie_present > 0)
82 return true;
83 if (oxpcie_present < 0)
84 return false;
86 /* not reached */
87 return false;
90 uintptr_t uart_platform_base(unsigned int idx)
92 if ((idx < 8) && oxpcie_uart_active())
93 return uart0_base + idx * 0x200;
94 return 0;
97 void oxford_remap(u32 new_base)
99 #if ENV_RAMSTAGE
100 uart0_base = new_base + 0x1000;
101 #endif
104 unsigned int uart_platform_refclk(void)
106 return 62500000;