mb/google/fatcat/var/fatcat: Refactor GPIO programming for UFS support

[coreboot.git] / src / mainboard / google / brya / variants / vell / overridetree.cb

fw_config
        field DB_CELLULAR 0 0
                option DB_CELLULAR_ABSENT       0
                option DB_CELLULAR_PCIE         1
        end
        field KB_COLOR 1 1
                option KB_COLOR_WHITE           0
                option KB_COLOR_BLUE            1
        end
        field NAND 2 2
                option NAND_MICRON              0
                option NAND_KIOXIA              1
        end
        field WIFI_SAR_ID 30 31
                option WIFI_SAR_ID_0            0
                option WIFI_SAR_ID_1            1
        end
end
chip soc/intel/alderlake
        # Intel Common SoC Config
        #+-------------------+---------------------------+
        #| Field             |  Value                    |
        #+-------------------+---------------------------+
        #| GSPI1             | Fingerprint MCU           |
        #| I2C0              | Audio                     |
        #| I2C1              | cr50 TPM. Early init is   |
        #|                   | required to set up a BAR  |
        #|                   | for TPM communication     |
        #| I2C2              |                           |
        #| I2C3              | Touchscreen               |
        #| I2C5              | Trackpad                  |
        #+-------------------+---------------------------+
        register "common_soc_config" = "{
                .i2c[0] = {
                        .speed = I2C_SPEED_FAST_PLUS,
                        .speed_config[0] = {
                                .speed = I2C_SPEED_FAST_PLUS,
                                .scl_lcnt = 45,
                                .scl_hcnt = 33,
                                .sda_hold = 20,
                        },
                },
                .i2c[1] = {
                        .early_init = 1,
                        .speed = I2C_SPEED_FAST,
                        .rise_time_ns = 600,
                        .fall_time_ns = 400,
                        .data_hold_time_ns = 50,
                },
                .i2c[3] = {
                        .rise_time_ns = 650,
                        .fall_time_ns = 400,
                        .data_hold_time_ns = 50,
                },
                .i2c[7] = {
                        .speed = I2C_SPEED_FAST_PLUS,
                        .speed_config[0] = {
                                .speed = I2C_SPEED_FAST_PLUS,
                                .scl_lcnt = 45,
                                .scl_hcnt = 30,
                                .sda_hold = 20,
                        },
                },
        }"
        register "usb2_ports[4]" = "USB2_PORT_TYPE_C(OC3)"  # USB2_C3
        register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)"
        register "usb2_ports[8]" = "USB2_PORT_EMPTY"

        register "usb3_ports[0]" = "USB3_PORT_EMPTY"

        register "tcss_ports[3]" = "TCSS_PORT_DEFAULT(OC3)"
        register "sagv" = "SaGv_Enabled"

        # As per Intel Advisory doc#723158, the change is required to prevent possible
        # display flickering issue.
        register "usb2_phy_sus_pg_disable" = "1"

        # Set EPP to 50%: 50 * 256 / 100 = 0x80
        register "enable_energy_perf_pref" = "true"
        register "energy_perf_pref_value" = "0x80"

        # FIVR RFI Spread Spectrum 6%
        register "fivr_spread_spectrum" = "FIVR_SS_6"

        # I2C Port Config
        register "serial_io_i2c_mode" = "{
                [PchSerialIoIndexI2C0] = PchSerialIoPci,
                [PchSerialIoIndexI2C1] = PchSerialIoPci,
                [PchSerialIoIndexI2C2] = PchSerialIoPci,
                [PchSerialIoIndexI2C3] = PchSerialIoPci,
                [PchSerialIoIndexI2C4] = PchSerialIoDisabled,
                [PchSerialIoIndexI2C5] = PchSerialIoPci,
                [PchSerialIoIndexI2C6] = PchSerialIoDisabled,
                [PchSerialIoIndexI2C7] = PchSerialIoPci,
        }"
        device domain 0 on
                device ref igpu on
                        chip drivers/gfx/generic
                                register "device_count" = "5"
                                # DDIA for eDP
                                register "device[0].name" = ""LCD0""
                                # Internal panel on the first port of the graphics chip
                                register "device[0].type" = "panel"
                                # DDIB is unused and HDMI is not enumerated in the kernel, so no GFX device is added for DDIB
                                # TCP0 (DP-1) for port C0
                                register "device[1].name" = ""DD01""
                                register "device[1].use_pld" = "true"
                                register "device[1].pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(1, 1))"
                                # TCP1 (DP-2) for port C1
                                register "device[2].name" = ""DD02""
                                register "device[2].use_pld" = "true"
                                register "device[2].pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
                                # TCP2 (DP-3) for port C2
                                register "device[3].name" = ""DD03""
                                register "device[3].use_pld" = "true"
                                register "device[3].pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))"
                                # TCP3 (DP-4) for port C3
                                register "device[4].name" = ""DD04""
                                register "device[4].use_pld" = "true"
                                register "device[4].pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))"
                                device generic 0 on end
                        end
                end # Integrated Graphics Device
                device ref dtt on
                        chip drivers/intel/dptf
                                ## sensor information
                                register "options.tsr[0].desc" = ""DRAM""
                                register "options.tsr[1].desc" = ""Soc""
                                register "options.tsr[2].desc" = ""Charger""
                                register "options.tsr[3].desc" = ""Regulator""
                                # TODO: below values are initial reference values only
                                ## Passive Policy
                                register "policies.passive" = "{
                                        [0] = DPTF_PASSIVE(CPU,         CPU,           95, 5000),
                                        [1] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_0, 75, 5000),
                                        [2] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_1, 75, 5000),
                                        [3] = DPTF_PASSIVE(CHARGER,     TEMP_SENSOR_2, 75, 5000),
                                        [4] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_3, 75, 5000),
                                }"
                                ## Critical Policy
                                register "policies.critical" = "{
                                        [0] = DPTF_CRITICAL(CPU,               105, SHUTDOWN),
                                        [1] = DPTF_CRITICAL(TEMP_SENSOR_0,      85, SHUTDOWN),
                                        [2] = DPTF_CRITICAL(TEMP_SENSOR_1,      85, SHUTDOWN),
                                        [3] = DPTF_CRITICAL(TEMP_SENSOR_2,      85, SHUTDOWN),
                                        [4] = DPTF_CRITICAL(TEMP_SENSOR_3,      85, SHUTDOWN),
                                }"
                                register "controls.power_limits" = "{
                                        .pl1 = {
                                                        .min_power = 3000,
                                                        .max_power = 15000,
                                                        .time_window_min = 28 * MSECS_PER_SEC,
                                                        .time_window_max = 32 * MSECS_PER_SEC,
                                                        .granularity = 200,
                                                },
                                        .pl2 = {
                                                        .min_power = 55000,
                                                        .max_power = 55000,
                                                        .time_window_min = 28 * MSECS_PER_SEC,
                                                        .time_window_max = 32 * MSECS_PER_SEC,
                                                        .granularity = 1000,
                                                }
                                }"
                                ## Charger Performance Control (Control, mA)
                                register "controls.charger_perf" = "{
                                        [0] = { 255, 1700 },
                                        [1] = {  24, 1500 },
                                        [2] = {  16, 1000 },
                                        [3] = {   8,  500 }
                                }"
                                device generic 0 on end
                        end
                end
                device ref ipu on
                        chip drivers/intel/mipi_camera
                                register "acpi_uid" = "0x50000"
                                register "acpi_name" = ""IPU0""
                                register "device_type" = "INTEL_ACPI_CAMERA_CIO2"

                                register "cio2_num_ports" = "1"
                                register "cio2_lanes_used" = "{4}" # 4 CSI Camera lanes are used
                                register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0""
                                register "cio2_prt[0]" = "1"
                                device generic 0 on end
                        end
                end
                device ref pcie4_0 on
                        # Enable CPU PCIE RP 1 using CLK 1
                        register "cpu_pcie_rp[CPU_RP(1)]" = "{
                                .clk_req = 1,
                                .clk_src = 1,
                                .flags = PCIE_RP_LTR | PCIE_RP_AER,
                        }"
                end
                device ref tbt_pcie_rp3 on end
                device ref cnvi_wifi on
                        chip drivers/wifi/generic
                                register "wake" = "GPE0_PME_B0"
                                device generic 0 on end
                        end
                end
                device ref pcie_rp6 on
                        # Enable WWAN PCIE 6 using clk 5
                        register "pch_pcie_rp[PCH_RP(6)]" = "{
                                .clk_src = 5,
                                .clk_req = 5,
                                .flags = PCIE_RP_LTR | PCIE_RP_AER,
                        }"
                        chip soc/intel/common/block/pcie/rtd3
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)"
                                register "reset_off_delay_ms" = "20"
                                register "srcclk_pin" = "5"
                                register "ext_pm_support" = "ACPI_PCIE_RP_EMIT_ALL"
                                register "skip_on_off_support" = "true"
                                register "use_rp_mutex" = "true"
                                device generic 0 alias rp6_rtd3 on end
                        end
                        chip drivers/wwan/fm
                                register "fcpo_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F21)"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E16)"
                                register "perst_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E0)"
                                register "wake_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A7)"
                                register "add_acpi_dma_property" = "true"
                                use rp6_rtd3 as rtd3dev
                                device generic 0 alias rp6_wwan on end
                        end
                end
                device ref pcie_rp8 off end
                device ref pcie_rp9 off end
                device ref tcss_dma0 on
                        chip drivers/intel/usb4/retimer
                                register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
                                use tcss_usb3_port1 as dfp[0].typec_port
                                device generic 0 on end
                        end
                end
                device ref tcss_dma1 on
                        chip drivers/intel/usb4/retimer
                                register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)"
                                use tcss_usb3_port3 as dfp[0].typec_port
                                device generic 0 on end
                        end
                end
                device ref i2c0 on
                        chip drivers/i2c/cs35l53
                                register "name" = ""SPK0""
                                register "sub" = ""103C8C08""
                                register "desc" = ""Cirrus Logic CS35L53 Tweeter Left Audio Codec""
                                register "uid" = "2"
                                register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
                                register "boost_type" = "EXTERNAL_BOOST"
                                register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED"
                                register "gpio1_output_enable" = "true"
                                register "gpio1_src_select" = "GPIO1_SRC_GPIO"
                                register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE"
                                device i2c 0x40 alias i2c0_cs35l53_0 on end
                        end
                        chip drivers/i2c/cs35l53
                                register "name" = ""SPK1""
                                register "sub" = ""103C8C08""
                                register "desc" = ""Cirrus Logic CS35L53 Woofer Left Audio Codec""
                                register "uid" = "0"
                                register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
                                register "boost_type" = "EXTERNAL_BOOST"
                                register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED"
                                register "gpio1_output_enable" = "true"
                                register "gpio1_src_select" = "GPIO1_SRC_GPIO"
                                register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE"
                                device i2c 0x41 alias i2c0_cs35l53_1 on end
                        end
                        chip drivers/i2c/cs35l53
                                register "name" = ""SPK2""
                                register "sub" = ""103C8C08""
                                register "desc" = ""Cirrus Logic CS35L53 Tweeter Right Audio Codec""
                                register "uid" = "3"
                                register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
                                register "boost_type" = "EXTERNAL_BOOST"
                                register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED"
                                register "gpio1_output_enable" = "true"
                                register "gpio1_src_select" = "GPIO1_SRC_GPIO"
                                register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE"
                                device i2c 0x42 on end
                        end
                        chip drivers/i2c/cs35l53
                                register "name" = ""SPK3""
                                register "sub" = ""103C8C08""
                                register "desc" = ""Cirrus Logic CS35L53 Woofer Right Audio Codec""
                                register "uid" = "1"
                                register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
                                register "boost_type" = "EXTERNAL_BOOST"
                                register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED"
                                register "gpio1_output_enable" = "true"
                                register "gpio1_src_select" = "GPIO1_SRC_GPIO"
                                register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE"
                                device i2c 0x43 on end
                        end
                end #I2C0
                device ref i2c1 on
                        chip drivers/i2c/tpm
                                register "hid" = ""GOOG0005""
                                register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
                                device i2c 50 on end
                        end
                end
                device ref i2c3 on
                        chip drivers/i2c/hid
                                register "generic.hid" = ""ELAN2513""
                                register "generic.desc" = ""ELAN Touchscreen""
                                register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
                                register "generic.detect" = "1"
                                register "generic.reset_gpio" =
                                                        "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
                                register "generic.reset_delay_ms" = "200"
                                register "generic.reset_off_delay_ms" = "1"
                                register "generic.enable_gpio" =
                                                        "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
                                register "generic.enable_delay_ms" = "6"
                                register "generic.stop_gpio" =
                                                        "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
                                register "generic.stop_off_delay_ms" = "1"
                                register "generic.has_power_resource" = "1"
                                register "hid_desc_reg_offset" = "0x01"
                                device i2c 0x10 on end
                        end
                end
                device ref i2c2 on
                        chip drivers/intel/mipi_camera
                                register "acpi_hid" = ""OVTI8856""
                                register "acpi_uid" = "0"
                                register "acpi_name" = ""CAM0""
                                register "chip_name" = ""Ov 8856 Camera""
                                register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"
                                register "has_power_resource" = "true"

                                register "ssdb.lanes_used" = "4"
                                register "ssdb.link_used" = "1"
                                register "num_freq_entries" = "2"
                                register "link_freq[0]" = "360000000"
                                register "link_freq[1]" = "180000000"
                                register "remote_name" = ""IPU0""
                                register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD"

                                #Controls
                                register "clk_panel.clks[0].clknum" = "IMGCLKOUT_2"
                                register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ"

                                register "gpio_panel.gpio[0].gpio_num" = "GPP_F20" #reset
                                register "gpio_panel.gpio[1].gpio_num" = "GPP_C4" #power

                                #_ON
                                register "on_seq.ops_cnt" = "4"
                                register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
                                register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)"
                                register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 5)"
                                register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 5)"

                                #_OFF
                                register "off_seq.ops_cnt" = "3"
                                register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
                                register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"
                                register "off_seq.ops[2]" = "SEQ_OPS_CLK_DISABLE(0, 0)"

                                device i2c 36 on end
                        end
                        chip drivers/intel/mipi_camera
                                register "acpi_hid" = "ACPI_DT_NAMESPACE_HID"
                                register "acpi_uid" = "1"
                                register "acpi_name" = ""NVM0""
                                register "chip_name" = ""GT24C08""
                                register "device_type" = "INTEL_ACPI_CAMERA_NVM"

                                register "nvm_compat" = ""atmel,24c1024""

                                register "nvm_size" = "0x2000"
                                register "nvm_pagesize" = "0x01"
                                register "nvm_readonly" = "0x01"
                                register "nvm_width" = "0x10"

                                device i2c 50 on end
                        end
                end
                device ref i2c5 on
                        chip drivers/i2c/hid
                                register "generic.hid" = ""ELAN2703""
                                register "generic.desc" = ""ELAN Touchpad""
                                register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
                                register "generic.wake" = "GPE0_DW2_14"
                                register "generic.detect" = "1"
                                register "hid_desc_reg_offset" = "0x01"
                                device i2c 15 on end
                        end
                end
                device ref i2c7 on
                        chip drivers/i2c/cs35l53
                                register "name" = ""SPK0""
                                register "sub" = ""103C8C08""
                                register "desc" = ""Cirrus Logic CS35L53 Tweeter Left Audio Codec""
                                register "uid" = "2"
                                register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
                                register "boost_type" = "EXTERNAL_BOOST"
                                register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED"
                                register "gpio1_output_enable" = "true"
                                register "gpio1_src_select" = "GPIO1_SRC_GPIO"
                                register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE"
                                device i2c 0x40 alias i2c7_cs35l53_0 on end
                        end
                        chip drivers/i2c/cs35l53
                                register "name" = ""SPK1""
                                register "sub" = ""103C8C08""
                                register "desc" = ""Cirrus Logic CS35L53 Woofer Left Audio Codec""
                                register "uid" = "0"
                                register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_D14)"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
                                register "boost_type" = "EXTERNAL_BOOST"
                                register "asp_sdout_hiz" = "ASP_SDOUT_LOGIC0_UNUSED_LOGIC0_DISABLED"
                                register "gpio1_output_enable" = "true"
                                register "gpio1_src_select" = "GPIO1_SRC_GPIO"
                                register "gpio2_src_select" = "GPIO2_SRC_HIGH_IMPEDANCE"
                                device i2c 0x41 alias i2c7_cs35l53_1 on end
                        end
                end
                device ref gspi1 on
                        chip drivers/spi/acpi
                                register "name" = ""CRFP""
                                register "hid" = "ACPI_DT_NAMESPACE_HID"
                                register "uid" = "1"
                                register "compat_string" = ""google,cros-ec-spi""
                                register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)"
                                register "wake" = "GPE0_DW2_15"
                                register "has_power_resource" = "true"
                                register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)"
                                register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)"
                                register "enable_delay_ms" = "3"
                                device spi 0 hidden end
                        end # FPMCU
                end
                device ref pch_espi on
                        chip ec/google/chromeec
                                use conn0 as mux_conn[0]
                                use conn1 as mux_conn[1]
                                use conn2 as mux_conn[2]
                                use conn3 as mux_conn[3]
                                device pnp 0c09.0 on end
                        end
                end
                device ref pmc hidden
                        chip drivers/intel/pmc_mux
                                device generic 0 on
                                        chip drivers/intel/pmc_mux/conn
                                                use usb2_port1 as usb2_port
                                                use tcss_usb3_port1 as usb3_port
                                                device generic 0 alias conn0 on end
                                        end
                                        chip drivers/intel/pmc_mux/conn
                                                use usb2_port2 as usb2_port
                                                use tcss_usb3_port2 as usb3_port
                                                device generic 1 alias conn1 on end
                                        end
                                        chip drivers/intel/pmc_mux/conn
                                                use usb2_port3 as usb2_port
                                                use tcss_usb3_port3 as usb3_port
                                                device generic 2 alias conn2 on end
                                        end
                                        chip drivers/intel/pmc_mux/conn
                                                use usb2_port5 as usb2_port
                                                use tcss_usb3_port4 as usb3_port
                                                device generic 3 alias conn3 on end
                                        end
                                end
                        end
                end
                device ref tcss_xhci on
                        chip drivers/usb/acpi
                                device ref tcss_root_hub on
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB3 Type-C Port C0 (MLB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(1, 1))"
                                                device ref tcss_usb3_port1 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB3 Type-C Port C1 (MlB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
                                                device ref tcss_usb3_port2 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB3 Type-C Port C2 (DB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))"
                                                device ref tcss_usb3_port3 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB3 Type-C Port C3 (DB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))"
                                                device ref tcss_usb3_port4 on end
                                        end
                                end
                        end
                end
                device ref xhci on
                        chip drivers/usb/acpi
                                device ref xhci_root_hub on
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB2 Type-C Port C0 (MLB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(1, 1))"
                                                device ref usb2_port1 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB2 Type-C Port C1 (MLB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
                                                device ref usb2_port2 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB2 Type-C Port C2 (DB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))"
                                                device ref usb2_port3 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB2 WWAN""
                                                register "type" = "UPC_TYPE_INTERNAL"
                                                device ref usb2_port4 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB2 Type-C Port C3 (DB)""
                                                register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
                                                register "use_custom_pld" = "true"
                                                register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(4, 1))"
                                                device ref usb2_port5 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB2 Camera""
                                                register "type" = "UPC_TYPE_INTERNAL"
                                                device ref usb2_port6 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""RGB Keyboard""
                                                register "type" = "UPC_TYPE_INTERNAL"
                                                device ref usb2_port7 on end
                                        end
                                        chip drivers/usb/acpi
                                                register "desc" = ""USB3 WWAN""
                                                register "type" = "UPC_TYPE_INTERNAL"
                                                device ref usb3_port4 on end
                                        end
                                end
                        end
                end
        end
end