src/mainboard/google/octopus/variants/bobba/overridetree.cb

   1 chip soc/intel/apollolake
   2
   3         # EMMC Tx CMD Delay
   4         # Refer to EDS-Vol2-16.32.
   5         # [14:8] steps of delay for DDR mode, each 125ps.
   6         # [6:0] steps of delay for SDR mode, each 125ps.
   7         register "emmc_tx_cmd_cntl" = "0x505"
   8
   9         # EMMC TX DATA Delay 1
  10         # Refer to EDS-Vol2-16.33.
  11         # [14:8] steps of delay for HS400, each 125ps.
  12         # [6:0] steps of delay for SDR104/HS200, each 125ps.
  13         register "emmc_tx_data_cntl1" = "0x0a0b"
  14
  15         # EMMC TX DATA Delay 2
  16         # Refer to EDS-Vol2-16.34.
  17         # [30:24] steps of delay for SDR50, each 125ps.
  18         # [22:16] steps of delay for DDR50, each 125ps.
  19         # [14:8] steps of delay for SDR25/HS50, each 125ps.
  20         # [6:0] steps of delay for SDR12, each 125ps.
  21         register "emmc_tx_data_cntl2" = "0x1c272828"
  22
  23         # EMMC RX CMD/DATA Delay 1
  24         # Refer to EDS-Vol2-16.35.
  25         # [30:24] steps of delay for SDR50, each 125ps.
  26         # [22:16] steps of delay for DDR50, each 125ps.
  27         # [14:8] steps of delay for SDR25/HS50, each 125ps.
  28         # [6:0] steps of delay for SDR12, each 125ps.
  29         register "emmc_rx_cmd_data_cntl1" = "0x00181b1a"
  30
  31         # EMMC RX CMD/DATA Delay 2
  32         # Refer to EDS-Vol2-16.37.
  33         # [17:16] stands for Rx Clock before Output Buffer
  34         # [14:8] steps of delay for Auto Tuning Mode, each 125ps.
  35         # [6:0] steps of delay for HS200, each 125ps.
  36         register "emmc_rx_cmd_data_cntl2" = "0x10021"
  37
  38         # EMMC Rx Strobe Delay
  39         # Refer to EDS-Vol2-16.36.
  40         # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps.
  41         # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps.
  42         register "emmc_rx_strobe_cntl" = "0x0a0a"
  43
  44         # Intel Common SoC Config
  45         #+-------------------+---------------------------+
  46         #| Field             |  Value                    |
  47         #+-------------------+---------------------------+
  48         #| GSPI0             | cr50 TPM. Early init is   |
  49         #|                   | required to set up a BAR  |
  50         #|                   | for TPM communication     |
  51         #|                   | before memory is up       |
  52         #| I2C0              | Digitizer                 |
  53         #| I2C5              | Audio                     |
  54         #| I2C6              | Trackpad                  |
  55         #| I2C7              | Touchscreen               |
  56         #+-------------------+---------------------------+
  57
  58         register "tcc_offset" = "10"
  59
  60         register "common_soc_config" = "{
  61                 .gspi[0] = {
  62                         .speed_mhz = 1,
  63                         .early_init = 1,
  64                 },
  65                 .i2c[0] = {
  66                         .speed = I2C_SPEED_FAST,
  67                         .rise_time_ns = 88,
  68                         .fall_time_ns = 16,
  69                 },
  70                 .i2c[1] = {
  71                         .speed = I2C_SPEED_FAST,
  72                         .rise_time_ns = 66,
  73                         .fall_time_ns = 90,
  74                         .data_hold_time_ns = 350,
  75                 },
  76                 .i2c[5] = {
  77                         .speed = I2C_SPEED_FAST,
  78                         .rise_time_ns = 104,
  79                         .fall_time_ns = 52,
  80                 },
  81                 .i2c[6] = {
  82                         .speed = I2C_SPEED_FAST,
  83                         .rise_time_ns = 66,
  84                         .fall_time_ns = 90,
  85                         .data_hold_time_ns = 350,
  86                 },
  87                 .i2c[7] = {
  88                         .speed = I2C_SPEED_FAST,
  89                         .rise_time_ns = 44,
  90                         .fall_time_ns = 90,
  91                 },
  92         }"
  93
  94         device domain 0 on
  95                 device pci 16.0 on
  96                         chip drivers/i2c/hid
  97                                 register "generic.hid" = ""WCOM50C1""
  98                                 register "generic.desc" = ""WCOM Digitizer""
  99                                 register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_139_IRQ)"
 100                                 register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_140)"
 101                                 register "generic.reset_delay_ms" = "20"
 102                                 register "generic.has_power_resource" = "1"
 103                                 register "generic.detect" = "1"
 104                                 register "hid_desc_reg_offset" = "0x1"
 105                                 device i2c 0x9 on end
 106                         end
 107                         chip drivers/generic/gpio_keys
 108                                 register "name" = ""PENH""
 109                                 register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPIO_145)"
 110                                 register "key.dev_name" = ""EJCT""
 111                                 register "key.linux_code" = "SW_PEN_INSERTED"
 112                                 register "key.linux_input_type" = "EV_SW"
 113                                 register "key.label" = ""pen_eject""
 114                                 register "key.wake_gpe" = "GPE0_DW2_04"
 115                                 register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
 116                                 register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
 117                                 device generic 0 on end
 118                         end
 119                 end     # - I2C 0
 120                 device pci 16.1 on
 121                         chip drivers/i2c/sx9310
 122                                 register "desc" = ""SAR Proximity Sensor""
 123                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_214_IRQ)"
 124                                 register "uid" = "1"
 125                                 register "cs0_ground" = "0x0"
 126                                 register "combined_sensors_count" = "2"
 127                                 register "combined_sensors[0]" = "1"
 128                                 register "combined_sensors[1]" = "2"
 129                                 register "resolution" = "SX9310_FINEST"
 130                                 register "avg_pos_strength" = "512"
 131                                 register "startup_sensor" = "1"
 132                                 register "proxraw_strength" = "0"
 133                                 device i2c 28 on end
 134                         end
 135                 end     # - I2C 1
 136                 device pci 17.1 on
 137                         chip drivers/i2c/da7219
 138                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
 139                                 register "btn_cfg" = "50"
 140                                 register "mic_det_thr" = "200"
 141                                 register "jack_ins_deb" = "20"
 142                                 register "jack_det_rate" = ""32ms_64ms""
 143                                 register "jack_rem_deb" = "1"
 144                                 register "a_d_btn_thr" = "0xa"
 145                                 register "d_b_btn_thr" = "0x16"
 146                                 register "b_c_btn_thr" = "0x21"
 147                                 register "c_mic_btn_thr" = "0x3e"
 148                                 register "btn_avg" = "4"
 149                                 register "adc_1bit_rpt" = "1"
 150                                 register "micbias_lvl" = "2600"
 151                                 register "mic_amp_in_sel" = ""diff""
 152                                 device i2c 1a on end
 153                         end
 154                         chip drivers/i2c/generic
 155                                 register "hid" = ""10EC5682""
 156                                 register "name" = ""RT58""
 157                                 register "desc" = ""Realtek RT5682""
 158                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_137_IRQ)"
 159                                 register "probed" = "1"
 160                                 register "property_count" = "1"
 161                                 # Set the jd_src to RT5668_JD1 for jack detection
 162                                 register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
 163                                 register "property_list[0].name" = ""realtek,jd-src""
 164                                 register "property_list[0].integer" = "1"
 165                                 device i2c 1a on end
 166                         end
 167                 end     # - I2C 5
 168                 device pci 17.2 on
 169                         chip drivers/i2c/generic
 170                                 register "hid" = ""ELAN0000""
 171                                 register "desc" = ""ELAN Touchpad""
 172                                 register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPIO_135_IRQ)"
 173                                 register "wake" = "GPE0_DW3_27"
 174                                 register "detect" = "1"
 175                                 device i2c 15 on end
 176                         end
 177                         chip drivers/i2c/hid
 178                                 register "generic.hid" = ""SYNA0000""
 179                                 register "generic.cid" = ""ACPI0C50""
 180                                 register "generic.desc" = ""Synaptics Touchpad""
 181                                 register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPIO_135_IRQ)"
 182                                 register "generic.wake" = "GPE0_DW3_27"
 183                                 register "generic.detect" = "1"
 184                                 register "hid_desc_reg_offset" = "0x20"
 185                                 device i2c 0x2c on end
 186                         end
 187                 end     # - I2C 6
 188                 device pci 17.3 on
 189                         chip drivers/i2c/generic
 190                                 register "hid" = ""ELAN0001""
 191                                 register "desc" = ""ELAN Touchscreen""
 192                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)"
 193                                 register "detect" = "1"
 194                                 register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
 195                                 register "reset_delay_ms" = "20"
 196                                 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
 197                                 register "enable_delay_ms" = "1"
 198                                 register "has_power_resource" = "true"
 199                                 device i2c 10 on end
 200                         end
 201                         chip drivers/i2c/generic
 202                                 register "hid" = ""RAYD0001""
 203                                 register "desc" = ""Raydium Touchscreen""
 204                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)"
 205                                 register "detect" = "1"
 206                                 register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
 207                                 register "reset_delay_ms" = "1"
 208                                 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
 209                                 register "enable_delay_ms" = "50"
 210                                 register "has_power_resource" = "true"
 211                                 device i2c 39 on end
 212                         end
 213                         chip drivers/i2c/hid
 214                                 register "generic.hid" = ""GTCH7502""
 215                                 register "generic.desc" = ""G2TOUCH Touchscreen""
 216                                 register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_212_IRQ)"
 217                                 register "generic.detect" = "1"
 218                                 register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)"
 219                                 register "generic.reset_delay_ms" = "70"
 220                                 register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_146)"
 221                                 register "generic.enable_delay_ms" = "1"
 222                                 register "generic.has_power_resource" = "1"
 223                                 register "hid_desc_reg_offset" = "0x01"
 224                                 device i2c 40 on end
 225                         end
 226                 end     # - I2C 7
 227         end
 228
 229         # Disable compliance mode
 230         register "disable_compliance_mode" = "1"
 231         register "disable_xhci_lfps_pm" = "0"
 232 end