drivers/mipi: Add support for KD_KD110N11_51IE panel
[coreboot2.git] / src / mainboard / google / brya / variants / yaviks / overridetree.cb
blob5a3a7d8b5e6ee9be96cfff43222f58c87c861ddc
1 fw_config
2 field DB_USB 0 1
3 option DB_1A 0
4 option DB_1C_1A 1
5 option DB_1C 2
6 option DB_1C_LTE 3
7 end
8 field WIFI_SAR_ID 2 3
9 option SAR_ID_0 0
10 option SAR_ID_1 1
11 option SAR_ID_2 2
12 option SAR_ID_3 3
13 end
14 field STYLUS 9
15 option STYLUS_ABSENT 0
16 option STYLUS_PRESENT 1
17 end
18 field SD_CARD 10
19 option SD_PRESENT 0
20 option SD_ABSENT 1
21 end
22 field WFC 11
23 option WFC_ABSENT 0
24 option WFC_MIPI_OVTI8856 1
25 end
26 field MB_HDMI 12
27 option HDMI_ABSENT 0
28 option HDMI_PRESENT 1
29 end
30 field MB_USB 15
31 option MB_1C 0
32 option MB_1C_2A 1
33 end
34 field TOUCH_PANEL 40 41
35 option TOUCH_HID_I2C 0
36 option TOUCH_I2C 1
37 end
38 end
40 chip soc/intel/alderlake
41 register "sagv" = "SaGv_Enabled"
43 # EMMC Tx CMD Delay
44 # Refer to EDS-Vol2-42.3.7.
45 # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39.
46 # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39.
47 register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505"
49 # EMMC TX DATA Delay 1
50 # Refer to EDS-Vol2-42.3.8.
51 # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78.
52 # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79.
53 register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909"
55 # EMMC TX DATA Delay 2
56 # Refer to EDS-Vol2-42.3.9.
57 # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79.
58 # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
59 # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79.
60 # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79.
61 register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828"
63 # EMMC RX CMD/DATA Delay 1
64 # Refer to EDS-Vol2-42.3.10.
65 # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119.
66 # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78.
67 # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119.
68 # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119.
69 register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B193b"
71 # EMMC RX CMD/DATA Delay 2
72 # Refer to EDS-Vol2-42.3.12.
73 # [17:16] stands for Rx Clock before Output Buffer,
74 # 00: Rx clock after output buffer,
75 # 01: Rx clock before output buffer,
76 # 10: Automatic selection based on working mode.
77 # 11: Reserved
78 # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39.
79 # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79.
80 register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10004"
82 # EMMC Rx Strobe Delay
83 # Refer to EDS-Vol2-42.3.11.
84 # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39.
85 # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39.
86 register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515"
88 # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC.
89 # Bit 2 - C1 has a redriver which does SBU muxing.
90 # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1.
91 register "tcss_aux_ori" = "1"
93 register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
95 register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # USB2 WWAN
96 register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN
97 register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
99 register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 WWAN
101 # Configure external V1P05/Vnn/VnnSx Rails
102 register "ext_fivr_settings" = "{
103 .configure_ext_fivr = 1,
106 # Intel Common SoC Config
107 #+-------------------+---------------------------+
108 #| Field | Value |
109 #+-------------------+---------------------------+
110 #| I2C0 | TPM. Early init is |
111 #| | required to set up a BAR |
112 #| | for TPM communication |
113 #| I2C1 | Touchscreen |
114 #| I2C2 | WCAM |
115 #| I2C3 | Audio |
116 #| I2C5 | Trackpad |
117 #+-------------------+---------------------------+
118 register "common_soc_config" = "{
119 .i2c[0] = {
120 .early_init = 1,
121 .speed = I2C_SPEED_FAST_PLUS,
122 .speed_config[0] = {
123 .speed = I2C_SPEED_FAST_PLUS,
124 .scl_lcnt = 56,
125 .scl_hcnt = 30,
126 .sda_hold = 7,
129 .i2c[1] = {
130 .speed = I2C_SPEED_FAST,
131 .speed_config[0] = {
132 .speed = I2C_SPEED_FAST,
133 .scl_lcnt = 158,
134 .scl_hcnt = 79,
135 .sda_hold = 30,
138 .i2c[2] = {
139 .speed = I2C_SPEED_FAST,
140 .speed_config[0] = {
141 .speed = I2C_SPEED_FAST,
142 .scl_lcnt = 158,
143 .scl_hcnt = 79,
144 .sda_hold = 7,
147 .i2c[3] = {
148 .speed = I2C_SPEED_FAST,
149 .speed_config[0] = {
150 .speed = I2C_SPEED_FAST,
151 .scl_lcnt = 158,
152 .scl_hcnt = 79,
153 .sda_hold = 7,
156 .i2c[5] = {
157 .speed = I2C_SPEED_FAST,
158 .speed_config[0] = {
159 .speed = I2C_SPEED_FAST,
160 .scl_lcnt = 158,
161 .scl_hcnt = 79,
162 .sda_hold = 40,
167 device domain 0 on
168 device ref dtt on
169 chip drivers/intel/dptf
170 ## sensor information
171 register "options.tsr[0].desc" = ""CPU""
172 register "options.tsr[1].desc" = ""5V Regulator""
173 register "options.tsr[2].desc" = ""Charger""
175 # TODO: below values are initial reference values only
176 ## Passive Policy
177 register "policies.passive" = "{
178 [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
179 [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
180 [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
181 [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
184 ## Critical Policy
185 register "policies.critical" = "{
186 [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
187 [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
188 [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
189 [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
192 register "controls.power_limits" = "{
193 .pl1 = {
194 .min_power = 3000,
195 .max_power = 6000,
196 .time_window_min = 28 * MSECS_PER_SEC,
197 .time_window_max = 32 * MSECS_PER_SEC,
198 .granularity = 200
200 .pl2 = {
201 .min_power = 25000,
202 .max_power = 25000,
203 .time_window_min = 28 * MSECS_PER_SEC,
204 .time_window_max = 32 * MSECS_PER_SEC,
205 .granularity = 1000
209 ## Charger Performance Control (Control, mA)
210 register "controls.charger_perf" = "{
211 [0] = { 255, 1700 },
212 [1] = { 24, 1500 },
213 [2] = { 16, 1000 },
214 [3] = { 8, 500 }
217 device generic 0 on end
220 device ref ipu on
221 chip drivers/intel/mipi_camera
222 register "acpi_uid" = "0x50000"
223 register "acpi_name" = ""IPU0""
224 register "device_type" = "INTEL_ACPI_CAMERA_CIO2"
226 register "cio2_num_ports" = "1"
227 register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used
228 register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0""
229 register "cio2_prt[0]" = "1"
230 device generic 0 on end
232 probe WFC WFC_MIPI_OVTI8856
234 device ref i2c1 on
235 chip drivers/i2c/generic
236 register "hid" = ""ELAN0001""
237 register "desc" = ""ELAN Touchscreen""
238 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
239 register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
240 register "reset_delay_ms" = "20"
241 register "reset_off_delay_ms" = "2"
242 register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
243 register "stop_delay_ms" = "20"
244 register "stop_off_delay_ms" = "2"
245 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
246 register "enable_delay_ms" = "5"
247 register "has_power_resource" = "1"
248 device i2c 10 on
249 probe TOUCH_PANEL TOUCH_I2C
252 chip drivers/i2c/hid
253 register "generic.hid" = ""ELAN2513""
254 register "generic.desc" = ""ELAN Touchscreen""
255 register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
256 register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
257 register "generic.reset_delay_ms" = "20"
258 register "generic.reset_off_delay_ms" = "2"
259 register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
260 register "generic.stop_delay_ms" = "280"
261 register "generic.stop_off_delay_ms" = "2"
262 register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
263 register "generic.enable_delay_ms" = "1"
264 register "generic.has_power_resource" = "1"
265 register "hid_desc_reg_offset" = "0x01"
266 device i2c 10 on
267 probe TOUCH_PANEL TOUCH_HID_I2C
270 chip drivers/i2c/hid
271 register "generic.hid" = ""ELAN900C""
272 register "generic.desc" = ""ELAN Touchscreen""
273 register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
274 register "generic.detect" = "1"
275 register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
276 register "generic.reset_delay_ms" = "20"
277 register "generic.reset_off_delay_ms" = "2"
278 register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
279 register "generic.stop_delay_ms" = "280"
280 register "generic.stop_off_delay_ms" = "2"
281 register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
282 register "generic.enable_delay_ms" = "1"
283 register "generic.has_power_resource" = "1"
284 register "hid_desc_reg_offset" = "0x01"
285 device i2c 15 on end
287 chip drivers/i2c/hid
288 register "generic.hid" = ""GTCH7503""
289 register "generic.desc" = ""G2TOUCH Touchscreen""
290 register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
291 register "generic.detect" = "1"
292 register "generic.reset_gpio" =
293 "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
294 register "generic.reset_delay_ms" = "50"
295 register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
296 register "generic.stop_delay_ms" = "55"
297 register "generic.stop_off_delay_ms" = "5"
298 register "generic.enable_gpio" =
299 "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
300 register "generic.enable_delay_ms" = "1"
301 register "generic.has_power_resource" = "1"
302 register "hid_desc_reg_offset" = "0x01"
303 device i2c 40 on end
305 chip drivers/generic/gpio_keys
306 register "name" = ""PENH""
307 register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)"
308 register "key.wake_gpe" = "GPE0_DW2_15"
309 register "key.wakeup_route" = "WAKEUP_ROUTE_SCI"
310 register "key.wakeup_event_action" = "EV_ACT_DEASSERTED"
311 register "key.dev_name" = ""EJCT""
312 register "key.linux_code" = "SW_PEN_INSERTED"
313 register "key.linux_input_type" = "EV_SW"
314 register "key.label" = ""pen_eject""
315 device generic 0 on
316 probe STYLUS STYLUS_PRESENT
320 device ref i2c2 on
321 chip drivers/intel/mipi_camera
322 register "acpi_hid" = ""OVTI8856""
323 register "acpi_uid" = "0"
324 register "acpi_name" = ""CAM0""
325 register "chip_name" = ""Ov 8856 Camera""
326 register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"
327 register "has_power_resource" = "1"
329 register "ssdb.lanes_used" = "2"
330 register "ssdb.link_used" = "1"
331 register "ssdb.vcm_type" = "0x0C"
332 register "vcm_name" = ""VCM0""
333 register "num_freq_entries" = "2"
334 register "link_freq[0]" = "360000000"
335 register "link_freq[1]" = "180000000"
336 register "remote_name" = ""IPU0""
338 #Controls
339 register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3"
340 register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ"
342 register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X
343 register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X
344 register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L
346 #_ON
347 register "on_seq.ops_cnt" = "5"
348 register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
349 register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)"
350 register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)"
351 register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)"
352 register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)"
354 #_OFF
355 register "off_seq.ops_cnt" = "4"
356 register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
357 register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
358 register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
359 register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"
361 device i2c 10 on
362 probe WFC WFC_MIPI_OVTI8856
365 chip drivers/intel/mipi_camera
366 register "acpi_uid" = "3"
367 register "acpi_name" = ""VCM0""
368 register "chip_name" = ""DW AF DAC""
369 register "device_type" = "INTEL_ACPI_CAMERA_VCM"
371 register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC""
372 register "vcm_compat" = ""dongwoon,dw9714""
374 device i2c 0C on
375 probe WFC WFC_MIPI_OVTI8856
378 chip drivers/intel/mipi_camera
379 register "acpi_hid" = "ACPI_DT_NAMESPACE_HID"
380 register "acpi_uid" = "1"
381 register "acpi_name" = ""NVM0""
382 register "chip_name" = ""GT24C08""
383 register "device_type" = "INTEL_ACPI_CAMERA_NVM"
385 register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC""
387 register "nvm_size" = "0x2000"
388 register "nvm_pagesize" = "1"
389 register "nvm_readonly" = "1"
390 register "nvm_width" = "0x10"
391 register "nvm_compat" = ""atmel,24c08""
393 device i2c 50 on
394 probe WFC WFC_MIPI_OVTI8856
398 device ref i2c3 on
399 chip drivers/i2c/generic
400 register "hid" = ""RTL5682""
401 register "name" = ""RT58""
402 register "desc" = ""Headset Codec""
403 register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
404 # Set the jd_src to RT5668_JD1 for jack detection
405 register "property_count" = "1"
406 register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
407 register "property_list[0].name" = ""realtek,jd-src""
408 register "property_list[0].integer" = "1"
409 device i2c 1a on end
412 device ref i2c5 on
413 chip drivers/i2c/generic
414 register "hid" = ""ELAN0000""
415 register "desc" = ""ELAN Touchpad""
416 register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
417 register "wake" = "GPE0_DW2_14"
418 register "detect" = "1"
419 device i2c 15 on end
421 chip drivers/i2c/hid
422 register "generic.hid" = ""SYNA0000""
423 register "generic.cid" = ""ACPI0C50""
424 register "generic.desc" = ""Synaptics Touchpad""
425 register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
426 register "generic.wake" = "GPE0_DW2_14"
427 register "generic.detect" = "1"
428 register "hid_desc_reg_offset" = "0x20"
429 device i2c 0x2c on end
432 device ref hda on
433 chip drivers/generic/max98357a
434 register "hid" = ""MX98360A""
435 register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
436 register "sdmode_delay" = "5"
437 device generic 0 on end
439 chip drivers/sof
440 register "spkr_tplg" = "max98360a"
441 register "jack_tplg" = "rt5682"
442 register "mic_tplg" = "_2ch_pdm0"
443 device generic 0 on end
446 device ref pcie_rp4 on
447 # PCIe 4 WLAN
448 register "pch_pcie_rp[PCH_RP(4)]" = "{
449 .clk_src = 2,
450 .clk_req = 2,
451 .flags = PCIE_RP_LTR | PCIE_RP_AER,
453 chip drivers/wifi/generic
454 register "wake" = "GPE0_DW1_03"
455 register "add_acpi_dma_property" = "true"
456 device pci 00.0 on end
459 device ref pcie_rp7 on
460 # Enable SD Card PCIe 7 using clk 3
461 register "pch_pcie_rp[PCH_RP(7)]" = "{
462 .clk_src = 3,
463 .clk_req = 3,
464 .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
466 chip soc/intel/common/block/pcie/rtd3
467 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
468 register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)"
469 register "srcclk_pin" = "3"
470 device generic 0 on end
472 probe SD_CARD SD_PRESENT
474 device ref emmc on end
475 device ref ish on
476 chip drivers/intel/ish
477 register "add_acpi_dma_property" = "true"
478 device generic 0 on end
481 device ref ufs on end
482 device ref pch_espi on
483 chip ec/google/chromeec
484 use conn0 as mux_conn[0]
485 use conn1 as mux_conn[1]
486 device pnp 0c09.0 on end
489 device ref pmc hidden
490 chip drivers/intel/pmc_mux
491 device generic 0 on
492 chip drivers/intel/pmc_mux/conn
493 use usb2_port1 as usb2_port
494 use tcss_usb3_port1 as usb3_port
495 device generic 0 alias conn0 on end
497 chip drivers/intel/pmc_mux/conn
498 use usb2_port2 as usb2_port
499 use tcss_usb3_port2 as usb3_port
500 device generic 1 alias conn1 on
501 probe DB_USB DB_1C_1A
502 probe DB_USB DB_1C
503 probe DB_USB DB_1C_LTE
509 device ref tcss_xhci on
510 chip drivers/usb/acpi
511 device ref tcss_root_hub on
512 chip drivers/usb/acpi
513 register "desc" = ""USB3 Type-C Port C0 (MLB)""
514 register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
515 register "use_custom_pld" = "true"
516 register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
517 device ref tcss_usb3_port1 on end
519 chip drivers/usb/acpi
520 register "desc" = ""USB3 Type-C Port C1 (DB)""
521 register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
522 register "use_custom_pld" = "true"
523 register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
524 device ref tcss_usb3_port2 on
525 probe DB_USB DB_1C_1A
526 probe DB_USB DB_1C
527 probe DB_USB DB_1C_LTE
533 device ref xhci on
534 chip drivers/usb/acpi
535 device ref xhci_root_hub on
536 chip drivers/usb/acpi
537 register "desc" = ""USB2 Type-C Port C0 (MLB)""
538 register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
539 register "use_custom_pld" = "true"
540 register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
541 device ref usb2_port1 on end
543 chip drivers/usb/acpi
544 register "desc" = ""USB2 Type-C Port C1 (DB)""
545 register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
546 register "use_custom_pld" = "true"
547 register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))"
548 device ref usb2_port2 on
549 probe DB_USB DB_1C_1A
550 probe DB_USB DB_1C
551 probe DB_USB DB_1C_LTE
554 chip drivers/usb/acpi
555 register "desc" = ""USB2 Type-A Port A0 (MLB)""
556 register "type" = "UPC_TYPE_A"
557 register "use_custom_pld" = "true"
558 register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(4, 1))"
559 device ref usb2_port3 on
560 probe MB_USB MB_1C_2A
563 chip drivers/usb/acpi
564 register "desc" = ""USB2 Type-A Port A1 (MLB)""
565 register "type" = "UPC_TYPE_A"
566 register "use_custom_pld" = "true"
567 register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(3, 1))"
568 device ref usb2_port4 on
569 probe MB_USB MB_1C_2A
572 chip drivers/usb/acpi
573 register "desc" = ""USB2 Type-A Port A1 (DB)""
574 register "type" = "UPC_TYPE_A"
575 register "use_custom_pld" = "true"
576 register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
577 device ref usb2_port4 on
578 probe DB_USB DB_1C_1A
579 probe DB_USB DB_1A
582 chip drivers/usb/acpi
583 register "desc" = ""USB2 WWAN""
584 register "type" = "UPC_TYPE_INTERNAL"
585 device ref usb2_port5 on
586 probe DB_USB DB_1C_LTE
589 chip drivers/usb/acpi
590 register "desc" = ""USB2 UFC""
591 register "type" = "UPC_TYPE_INTERNAL"
592 device ref usb2_port6 on end
594 chip drivers/usb/acpi
595 register "desc" = ""USB2 Bluetooth""
596 register "type" = "UPC_TYPE_INTERNAL"
597 register "reset_gpio" =
598 "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
599 device ref usb2_port8 on end
601 chip drivers/usb/acpi
602 register "desc" = ""CNVi Bluetooth""
603 register "type" = "UPC_TYPE_INTERNAL"
604 register "reset_gpio" =
605 "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
606 device ref usb2_port10 on end
608 chip drivers/usb/acpi
609 register "desc" = ""USB3 Type-A Port A0 (MLB)""
610 register "type" = "UPC_TYPE_USB3_A"
611 register "use_custom_pld" = "true"
612 register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(4, 1))"
613 device ref usb3_port1 on
614 probe MB_USB MB_1C_2A
617 chip drivers/usb/acpi
618 register "desc" = ""USB3 Type-A Port A1 (MLB)""
619 register "type" = "UPC_TYPE_USB3_A"
620 register "use_custom_pld" = "true"
621 register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(3, 1))"
622 device ref usb3_port2 on
623 probe MB_USB MB_1C_2A
626 chip drivers/usb/acpi
627 register "desc" = ""USB3 Type-A Port A1 (DB)""
628 register "type" = "UPC_TYPE_USB3_A"
629 register "use_custom_pld" = "true"
630 register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, RIGHT, ACPI_PLD_GROUP(3, 1))"
631 device ref usb3_port2 on
632 probe DB_USB DB_1C_1A
633 probe DB_USB DB_1A
636 chip drivers/usb/acpi
637 register "desc" = ""USB3 WWAN""
638 register "type" = "UPC_TYPE_INTERNAL"
639 device ref usb3_port3 on
640 probe DB_USB DB_1C_LTE