src/lib/ramtest.c

   1 /* SPDX-License-Identifier: GPL-2.0-only */
   2
   3 #include <stdint.h>
   4 #include <lib.h>
   5 #include <console/console.h>
   6 #include <device/mmio.h>
   7
   8 #if ENV_X86 && CONFIG(SSE2)
   9 /* Assembler in lib/ is ugly. */
  10 static void write_phys(uintptr_t addr, u32 value)
  11 {
  12         asm volatile (
  13                 "movnti %1, (%0)"
  14                 : /* outputs */
  15                 : "r" (addr), "r" (value) /* inputs */
  16         );
  17 }
  18
  19 static void phys_memory_barrier(void)
  20 {
  21         // Needed for movnti
  22         asm volatile ("sfence" ::: "memory");
  23 }
  24 #else
  25 static void write_phys(uintptr_t addr, u32 value)
  26 {
  27         write32p(addr, value);
  28 }
  29
  30 static void phys_memory_barrier(void)
  31 {
  32         asm volatile ("" ::: "memory");
  33 }
  34 #endif
  35
  36 static u32 read_phys(uintptr_t addr)
  37 {
  38         return read32p(addr);
  39 }
  40
  41 /**
  42  * Rotate ones test pattern that access every bit on a 128bit wide
  43  * memory bus. To test most address lines, addresses are scattered
  44  * using 256B, 4kB and 64kB increments.
  45  *
  46  * @param idx   Index to test pattern (0=<idx<0x400)
  47  * @param addr  Memory to access on idx
  48  * @param value Value to write or read at addr
  49  */
  50 static inline void test_pattern(unsigned short int idx,
  51         unsigned long *addr, unsigned long *value)
  52 {
  53         uint8_t j, k;
  54
  55         k = (idx >> 8) + 1;
  56         j = (idx >> 4) & 0x0f;
  57         *addr = idx & 0x0f;
  58         *addr |= j << (4*k);
  59         *value = 0x01010101 << (j & 7);
  60         if (j & 8)
  61                 *value = ~(*value);
  62 }
  63
  64 /**
  65  * Simple write-read-verify memory test. See console debug output for
  66  * any dislocated bytes.
  67  *
  68  * Tests 1MiB of memory starting from start.
  69  *
  70  * @param start   System memory offset, aligned to 128bytes
  71  */
  72 static int ram_bitset_nodie(uintptr_t start)
  73 {
  74         unsigned long addr, value, value2;
  75         unsigned short int idx;
  76         unsigned char failed, failures;
  77         uint8_t verbose = 0;
  78
  79         printk(BIOS_DEBUG, "DRAM bitset write: 0x%08lx\n", start);
  80         for (idx = 0; idx < 0x400; idx += 4) {
  81                 test_pattern(idx, &addr, &value);
  82                 write_phys(start + addr, value);
  83         }
  84
  85         /* Make sure we don't read before we wrote */
  86         phys_memory_barrier();
  87
  88         printk(BIOS_DEBUG, "DRAM bitset verify: 0x%08lx\n", start);
  89         failures = 0;
  90         for (idx = 0; idx < 0x400; idx += 4) {
  91                 test_pattern(idx, &addr, &value);
  92                 value2 = read_phys(start + addr);
  93
  94                 failed = (value2 != value);
  95                 failures |= failed;
  96                 if (failed && !verbose) {
  97                         printk(BIOS_ERR, "0x%08lx wr: 0x%08lx rd: 0x%08lx FAIL\n",
  98                                  start + addr, value, value2);
  99                 }
 100                 if (verbose) {
 101                         if ((addr & 0x0f) == 0)
 102                                 printk(BIOS_DEBUG, "%08lx wr: %08lx rd:",
 103                                         start + addr, value);
 104                         if (failed)
 105                                 printk(BIOS_DEBUG, " %08lx!", value2);
 106                         else
 107                                 printk(BIOS_DEBUG, " %08lx ", value2);
 108                         if ((addr & 0x0f) == 0xc)
 109                                 printk(BIOS_DEBUG, "\n");
 110                 }
 111         }
 112         if (failures) {
 113                 post_code(POSTCODE_RAM_FAILURE);
 114                 printk(BIOS_DEBUG, "\nDRAM did _NOT_ verify!\n");
 115                 return 1;
 116         }
 117         printk(BIOS_DEBUG, "\nDRAM range verified.\n");
 118         return 0;
 119 }
 120
 121
 122 void ram_check(uintptr_t start)
 123 {
 124         /*
 125          * This is much more of a "Is my DRAM properly configured?"
 126          * test than a "Is my DRAM faulty?" test.  Not all bits
 127          * are tested.   -Tyson
 128          */
 129         printk(BIOS_DEBUG, "Testing DRAM at: %08lx\n", start);
 130         if (ram_bitset_nodie(start))
 131                 die("DRAM ERROR");
 132         printk(BIOS_DEBUG, "Done.\n");
 133 }
 134
 135
 136 int ram_check_nodie(uintptr_t start)
 137 {
 138         int ret;
 139         /*
 140          * This is much more of a "Is my DRAM properly configured?"
 141          * test than a "Is my DRAM faulty?" test.  Not all bits
 142          * are tested.   -Tyson
 143          */
 144         printk(BIOS_DEBUG, "Testing DRAM at : %08lx\n", start);
 145
 146         ret = ram_bitset_nodie(start);
 147         printk(BIOS_DEBUG, "Done.\n");
 148         return ret;
 149 }
 150
 151 int ram_check_noprint_nodie(uintptr_t start)
 152 {
 153         unsigned long addr, value, value2;
 154         unsigned short int idx;
 155         unsigned char failed, failures;
 156
 157         for (idx = 0; idx < 0x400; idx += 4) {
 158                 test_pattern(idx, &addr, &value);
 159                 write_phys(start + addr, value);
 160         }
 161
 162         /* Make sure we don't read before we wrote */
 163         phys_memory_barrier();
 164
 165         failures = 0;
 166         for (idx = 0; idx < 0x400; idx += 4) {
 167                 test_pattern(idx, &addr, &value);
 168                 value2 = read_phys(start + addr);
 169
 170                 failed = (value2 != value);
 171                 failures |= failed;
 172         }
 173         return failures;
 174 }
 175
 176 /* Assumption is 32-bit addressable UC memory at dst. This also executes
 177  * on S3 resume path so target memory must be restored.
 178  */
 179 void quick_ram_check_or_die(uintptr_t dst)
 180 {
 181         int fail = 0;
 182         u32 backup;
 183         backup = read_phys(dst);
 184         write_phys(dst, 0x55555555);
 185         phys_memory_barrier();
 186         if (read_phys(dst) != 0x55555555)
 187                 fail = 1;
 188         write_phys(dst, 0xaaaaaaaa);
 189         phys_memory_barrier();
 190         if (read_phys(dst) != 0xaaaaaaaa)
 191                 fail = 1;
 192         write_phys(dst, 0x00000000);
 193         phys_memory_barrier();
 194         if (read_phys(dst) != 0x00000000)
 195                 fail = 1;
 196         write_phys(dst, 0xffffffff);
 197         phys_memory_barrier();
 198         if (read_phys(dst) != 0xffffffff)
 199                 fail = 1;
 200
 201         write_phys(dst, backup);
 202         if (fail) {
 203                 post_code(POSTCODE_RAM_FAILURE);
 204                 die("RAM INIT FAILURE!\n");
 205         }
 206         phys_memory_barrier();
 207 }