src/mainboard/google/reef/variants/coral/devicetree.cb

   1 chip soc/intel/apollolake
   2
   3         register "pcie_rp_clkreq_pin[0]" = "0"    # wifi/bt
   4         # Disable unused clkreq of PCIe root ports
   5         register "pcie_rp_clkreq_pin[1]" = "CLKREQ_DISABLED"
   6         register "pcie_rp_clkreq_pin[2]" = "CLKREQ_DISABLED"
   7         register "pcie_rp_clkreq_pin[3]" = "CLKREQ_DISABLED"
   8         register "pcie_rp_clkreq_pin[4]" = "CLKREQ_DISABLED"
   9         register "pcie_rp_clkreq_pin[5]" = "CLKREQ_DISABLED"
  10
  11         # GPIO for PERST_0
  12         # If the Board has PERST_0 signal, assign the GPIO
  13         # If the Board does not have PERST_0, assign GPIO_PRT0_UDEF
  14         register "prt0_gpio" = "GPIO_122"
  15
  16         # GPIO for SD card detect
  17         register "sdcard_cd_gpio" = "GPIO_177"
  18
  19         # EMMC TX DATA Delay 1
  20         # Refer to EDS-Vol2-22.3.
  21         # [14:8] steps of delay for HS400, each 125ps.
  22         # [6:0] steps of delay for SDR104/HS200, each 125ps.
  23         register "emmc_tx_data_cntl1" = "0x0C16"
  24
  25         # EMMC TX DATA Delay 2
  26         # Refer to EDS-Vol2-22.3.
  27         # [30:24] steps of delay for SDR50, each 125ps.
  28         # [22:16] steps of delay for DDR50, each 125ps.
  29         # [14:8] steps of delay for SDR25/HS50, each 125ps.
  30         # [6:0] steps of delay for SDR12, each 125ps.
  31         register "emmc_tx_data_cntl2" = "0x28162828"
  32
  33         # EMMC RX CMD/DATA Delay 1
  34         # Refer to EDS-Vol2-22.3.
  35         # [30:24] steps of delay for SDR50, each 125ps.
  36         # [22:16] steps of delay for DDR50, each 125ps.
  37         # [14:8] steps of delay for SDR25/HS50, each 125ps.
  38         # [6:0] steps of delay for SDR12, each 125ps.
  39         register "emmc_rx_cmd_data_cntl1" = "0x00181717"
  40
  41         # EMMC RX CMD/DATA Delay 2
  42         # Refer to EDS-Vol2-22.3.
  43         # [17:16] stands for Rx Clock before Output Buffer
  44         # [14:8] steps of delay for Auto Tuning Mode, each 125ps.
  45         # [6:0] steps of delay for HS200, each 125ps.
  46         register "emmc_rx_cmd_data_cntl2" = "0x10008"
  47
  48         # Enable DPTF
  49         register "dptf_enable" = "1"
  50
  51         # PL1 override 12 W: the energy calculation is wrong with the
  52         # current VR solution. Experiments show that SoC TDP max (6W) can
  53         # be reached when RAPL PL1 is set to 12W.
  54         # Set RAPL PL2 to 15W.
  55         register "power_limits_config" = "{
  56                 .tdp_pl1_override = 12,
  57                 .tdp_pl2_override = 15,
  58         }"
  59
  60         # Enable Audio Clock and Power gating
  61         register "hdaudio_clk_gate_enable" = "1"
  62         register "hdaudio_pwr_gate_enable" = "1"
  63         register "hdaudio_bios_config_lockdown" = "1"
  64
  65         # Enable lpss s0ix
  66         register "lpss_s0ix_enable" = "true"
  67
  68         # GPE configuration
  69         # Note that GPE events called out in ASL code rely on this
  70         # route, i.e., if this route changes then the affected GPE
  71         # offset bits also need to be changed. This sets the PMC register
  72         # GPE_CFG fields.
  73         register "gpe0_dw1" = "PMC_GPE_N_31_0"
  74         register "gpe0_dw2" = "PMC_GPE_N_63_32"
  75         register "gpe0_dw3" = "PMC_GPE_SW_31_0"
  76
  77         # Intel Common SoC Config
  78         #+-------------------+---------------------------+
  79         #| Field             |  Value                    |
  80         #+-------------------+---------------------------+
  81         #| I2C0              | Audio                     |
  82         #| I2C2              | TPM                       |
  83         #| I2C3              | Touchscreen               |
  84         #| I2C4              | Trackpad                  |
  85         #| I2C5              | Digitizer                 |
  86         #+-------------------+---------------------------+
  87         register "common_soc_config" = "{
  88                 .i2c[0] = {
  89                         .speed = I2C_SPEED_FAST,
  90                         .rise_time_ns = 104,
  91                         .fall_time_ns = 52,
  92                 },
  93                 .i2c[2] = {
  94                         .early_init = 1,
  95                         .speed = I2C_SPEED_FAST,
  96                         .rise_time_ns = 57,
  97                         .fall_time_ns = 28,
  98                 },
  99                 .i2c[3] = {
 100                         .speed = I2C_SPEED_FAST,
 101                         .rise_time_ns = 76,
 102                         .fall_time_ns = 164,
 103                 },
 104                 .i2c[4] = {
 105                         .speed = I2C_SPEED_FAST,
 106                         .rise_time_ns = 114,
 107                         .fall_time_ns = 164,
 108                         .data_hold_time_ns = 350,
 109                 },
 110                 .i2c[5] = {
 111                         .speed = I2C_SPEED_FAST,
 112                         .rise_time_ns = 152,
 113                         .fall_time_ns = 30,
 114                 },
 115         }"
 116
 117         # Minimum SLP S3 assertion width 28ms.
 118         register "slp_s3_assertion_width_usecs" = "28000"
 119
 120         device domain 0 on
 121                 device pci 00.0 on  end # - Host Bridge
 122                 device pci 00.1 on  end # - DPTF
 123                 device pci 00.2 off end # - NPK
 124                 device pci 02.0 on      # - Gen
 125                         register "gfx" = "GMA_DEFAULT_PANEL(0)"
 126                 end
 127                 device pci 03.0 off end # - Iunit
 128                 device pci 0d.0 on  end # - P2SB
 129                 device pci 0d.1 on  end # - PMC
 130                 device pci 0d.2 on  end # - SPI
 131                 device pci 0d.3 on  end # - Shared SRAM
 132                 device pci 0e.0 on      # - Audio
 133                         chip drivers/generic/max98357a
 134                                 register "hid" = ""MX98357A""
 135                                 register "sdmode_gpio" =  "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_76)"
 136                                 register "sdmode_delay" = "5"
 137                                 device generic 0 on end
 138                         end
 139                 end
 140                 device pci 0f.0 on  end # - CSE
 141                 device pci 11.0 off end # - ISH
 142                 device pci 12.0 off end # - SATA
 143                 device pci 13.0 off end # - Root Port 2 - PCIe-A 0
 144                 device pci 13.1 off end # - Root Port 3 - PCIe-A 1
 145                 device pci 13.2 off end # - Root Port 4 - PCIe-A 2
 146                 device pci 13.3 off end # - Root Port 5 - PCIe-A 3
 147                 device pci 14.0 on
 148                         chip drivers/wifi/generic
 149                                 register "wake" = "GPE0_DW3_00"
 150                                 device pci 00.0 on end
 151                         end
 152                 end     # - Root Port 0 - PCIe-B 0 - Wifi
 153                 device pci 14.1 off end # - Root Port 1 - PCIe-B 1
 154                 device pci 15.0 on  end # - XHCI
 155                 device pci 15.1 off end # - XDCI
 156                 device pci 16.0 on      # - I2C 0
 157                         chip drivers/i2c/da7219
 158                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_116_IRQ)"
 159                                 register "btn_cfg" = "50"
 160                                 register "mic_det_thr" = "200"
 161                                 register "jack_ins_deb" = "20"
 162                                 register "jack_det_rate" = ""32ms_64ms""
 163                                 register "jack_rem_deb" = "1"
 164                                 register "a_d_btn_thr" = "0xa"
 165                                 register "d_b_btn_thr" = "0x16"
 166                                 register "b_c_btn_thr" = "0x21"
 167                                 register "c_mic_btn_thr" = "0x3e"
 168                                 register "btn_avg" = "4"
 169                                 register "adc_1bit_rpt" = "1"
 170                                 register "micbias_lvl" = "2600"
 171                                 register "mic_amp_in_sel" = ""diff""
 172                                 device i2c 1a on end
 173                         end
 174                 end
 175                 device pci 16.1 on  end # - I2C 1
 176                 device pci 16.2 on
 177                         chip drivers/i2c/tpm
 178                                 register "hid" = ""GOOG0005""
 179                                 register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_28_IRQ)"
 180                                 device i2c 50 on end
 181                         end
 182                 end     # - I2C 2
 183                 device pci 16.3 on
 184                         chip drivers/i2c/generic
 185                                 register "hid" = ""ELAN0001""
 186                                 register "desc" = ""ELAN Touchscreen""
 187                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_21_IRQ)"
 188                                 register "detect" = "1"
 189                                 register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_36)"
 190                                 register "reset_delay_ms" = "20"
 191                                 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_152)"
 192                                 register "enable_delay_ms" = "1"
 193                                 register "has_power_resource" = "1"
 194                                 device i2c 10 on end
 195                         end
 196                         chip drivers/i2c/generic
 197                                 register "hid" = ""RAYD0001""
 198                                 register "desc" = ""Raydium Touchscreen""
 199                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_21_IRQ)"
 200                                 register "detect" = "1"
 201                                 register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_36)"
 202                                 register "reset_delay_ms" = "1"
 203                                 register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_152)"
 204                                 register "enable_delay_ms" = "50"
 205                                 register "has_power_resource" = "1"
 206                                 device i2c 39 on end
 207                         end
 208                 end     # - I2C 3
 209                 device pci 17.0 on
 210                         chip drivers/i2c/generic
 211                                 register "hid" = ""ELAN0000""
 212                                 register "desc" = ""ELAN Touchpad""
 213                                 register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_18_IRQ)"
 214                                 register "wake" = "GPE0_DW1_15"
 215                                 register "detect" = "1"
 216                                 device i2c 15 on end
 217                         end
 218                         chip drivers/i2c/hid
 219                                 register "generic.hid" = ""SYNA0000""
 220                                 register "generic.cid" = ""ACPI0C50""
 221                                 register "generic.desc" = ""Synaptics Touchpad""
 222                                 register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_18_IRQ)"
 223                                 register "generic.wake" = "GPE0_DW1_15"
 224                                 register "generic.detect" = "1"
 225                                 register "hid_desc_reg_offset" = "0x20"
 226                                 device i2c 0x2c on end
 227                         end
 228                 end # - I2C 4
 229                 device pci 17.1 on
 230                         chip drivers/i2c/hid
 231                                 register "generic.hid" = ""WCOM50C1""
 232                                 register "generic.desc" = ""WCOM Digitizer""
 233                                 register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_13_IRQ)"
 234                                 register "hid_desc_reg_offset" = "0x1"
 235                                 device i2c 0x9 on end
 236                         end
 237                 end     # - I2C 5
 238                 device pci 17.2 off end # - I2C 6
 239                 device pci 17.3 off end # - I2C 7
 240                 device pci 18.0 on  end # - UART 0
 241                 device pci 18.1 off end # - UART 1
 242                 device pci 18.2 off end # - UART 2
 243                 device pci 18.3 off end # - UART 3
 244                 device pci 19.0 on  end # - SPI 0
 245                 device pci 19.1 off end # - SPI 1
 246                 device pci 19.2 off end # - SPI 2
 247                 device pci 1a.0 on  end # - PWM
 248                 device pci 1b.0 on  end # - SDCARD
 249                 device pci 1c.0 on  end # - eMMC
 250                 device pci 1e.0 off end # - SDIO
 251                 device pci 1f.0 on      # - LPC
 252                         chip ec/google/chromeec
 253                                 device pnp 0c09.0 on end
 254                         end
 255                 end
 256                 device pci 1f.1 on  end # - SMBUS
 257         end
 258 end