mb/google/brya: Create rull variant

[coreboot2.git] / src / mainboard / kontron / ktqm77 / devicetree.cb

chip northbridge/intel/sandybridge
        # IGD Displays
        register "gfx" = "GMA_STATIC_DISPLAYS(0)"

        register "spd_addresses" = "{0x50, 0, 0x52, 0}"
        register "max_mem_clock_mhz" = "800"
        register "ec_present" = "1"

        register "usb3.hs_port_switch_mask" = "0xf"
        register "usb3.mode" = "3"
        register "usb3.preboot_support" = "1"
        register "usb3.xhci_streams" = "1"

        chip cpu/intel/model_206ax
                device cpu_cluster 0 on end

                register "acpi_c2" = "CPU_ACPI_C6"
                register "acpi_c3" = "CPU_ACPI_DISABLED"
        end

        device domain 0 on
                device ref host_bridge on end # host bridge
                device ref peg10 on end # PCIe Bridge x16
                device ref igd on end # vga controller

                chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH
                        # Enable all SATA ports 0-5
                        register "sata_port_map" = "0x3f"
                        # Set max SATA speed to 6.0 Gb/s (should be the default, anyway)
                        register "sata_interface_speed_support" = "0x3"

                        # TODO: Enable generic LPC decodes...
                        register "gen1_dec" = "0x001c02e1"
                        #register "gen2_dec" = "0x00000000"
                        #register "gen3_dec" = "0x00000000"
                        #register "gen4_dec" = "0x00000000"

                        # Disable root port coalescing
                        register "pcie_port_coalesce" = "false"

                        register "xhci_switchable_ports"        = "0x0f"
                        register "superspeed_capable_ports"     = "0x0f"
                        register "usb_port_config" = "{
                                { 1, 0, 0 }, /* P0: lower left USB 3.0 (OC0) */
                                { 1, 0, 0 }, /* P1: upper left USB 3.0 (OC0) */
                                { 1, 0, 0 }, /* P2: lower right USB 3.0 (OC0) */
                                { 1, 0, 0 }, /* P3: upper right USB 3.0 (OC0) */
                                { 1, 0, 0 }, /* P4: lower USB 2.0 (OC0) */
                                { 1, 0, 0 }, /* P5: upper USB 2.0 (OC0) */
                                { 1, 0, 0 }, /* P6: front panel USB 2.0 (OC0) */
                                { 1, 0, 0 }, /* P7: front panel USB 2.0 (OC0) */
                                { 1, 0, 4 }, /* P8: internal USB 2.0 (OC4) */
                                { 1, 0, 4 }, /* P9: internal USB 2.0 (OC4) */
                                { 1, 0, 4 }, /* P10: internal USB 2.0 (OC4) */
                                { 1, 0, 4 }, /* P11: internal USB 2.0 (OC4) */
                                { 1, 0, 4 }, /* P12: internal USB 2.0 (OC4) */
                                { 1, 0, 4 }, /* P13: internal USB 2.0 (OC4) */
                        }"

                        device ref xhci on end # USB 3.0 Controller
                        device ref mei1 on end # Management Engine Interface 1
                        device ref mei2 off end # Management Engine Interface 2
                        device ref me_ide_r off end # Management Engine IDE-R
                        device ref me_kt off end # Management Engine KT
                        device ref gbe on end # Intel Gigabit Ethernet
                        device ref ehci2 on end # USB2 EHCI #2
                        device ref hda on end # High Definition Audio

                        # Disabling 1c.0 might break IRQ settings as it enables port coalescing
                        # There are two mini PCIe x1 sockets, so one PCIe port is unrouted
                        device ref pcie_rp1 on end # PCIe Port #1 mini PCIe x1?
                        device ref pcie_rp2 on end # PCIe Port #2 mini PCIe x1?
                        device ref pcie_rp3 on end # PCIe Port #3 second Ethernet NIC
                        device ref pcie_rp4 on end # PCIe Port #4 third Ethernet NIC
                        device ref pcie_rp5 on end # PCIe Port #5 first Ethernet PHY
                        device ref pcie_rp6 on end # PCIe Port #6 FireWire
                        device ref pcie_rp7 on end # PCIe Port #7 PCIe x1
                        device ref pcie_rp8 on end # PCIe Port #8 mini PCIe x1?

                        device ref ehci1 on end # USB2 EHCI #1
                        device ref pci_bridge off end # PCI bridge
                        device ref lpc on #LPC bridge
                                chip superio/winbond/w83627dhg
                                        device pnp 2e.0 off #  Floppy
                                        end
                                        device pnp 2e.1 off #  Parallel Port
                                        end
                                        device pnp 2e.2 on #  Com1
                                                io 0x60 = 0x3f8
                                                irq 0x70 = 4
                                        end
                                        device pnp 2e.3 on #  Com2
                                                io 0x60 = 0x2f8
                                                irq 0x70 = 3
                                        end
                                        device pnp 2e.5 off #  Keyboard
                                        end
                                        device pnp 2e.6 off #  SPI
                                        end
                                        device pnp 2e.307 off #  GPIO 1
                                        end
                                        device pnp 2e.8 off #  WDTO#, PLED
                                        end
                                        device pnp 2e.009 on #  GPIO2 -- original firmware sets this on
                                        end
                                        device pnp 2e.109 on #  GPIO3 -- original firmware sets this on
                                        end
                                        device pnp 2e.209 off #  GPIO4
                                        end
                                        device pnp 2e.309 off #  GPIO5
                                        end
                                        device pnp 2e.a off #  ACPI
                                        end
                                        device pnp 2e.b off # HWM
                                        end
                                        device pnp 2e.c off # PECI, SST
                                        end
                                end     #superio/winbond/w83627dhg
                                chip ec/kontron/it8516e
                                        # Set CPU Fan to 50°C, System Fan to 75%
                                        register "default_fan_mode" = "{ IT8516E_MODE_THERMAL, IT8516E_MODE_PWM }"
                                        register "default_fan_target" = "{ 50, 75 }"

                                        # TODO: Check status when Linux runs
                                        device pnp 20e.1 on #  Com3
                                                io 0x60 = 0x03e8
                                                irq 0x70 = 4
                                        end
                                        device pnp 20e.2 on #  Com4
                                                io 0x60 = 0x02e8
                                                irq 0x70 = 3
                                        end
                                        device pnp 20e.4 off #  System Wakeup
                                        end
                                        device pnp 20e.5 on #  Mouse
                                                irq 0x70 = 12
                                        end
                                        device pnp 20e.6 on #  Keyboard
                                                io 0x60 = 0x0060
                                                io 0x62 = 0x0064
                                                irq 0x70 = 1
                                        end
                                        device pnp 20e.f off #  Shared Memory
                                        end
                                        device pnp 20e.10 off #  BRAM / RTC
                                        end
                                        device pnp 20e.11 on #  PM channel 1
                                                io 0x60 = 0x0062
                                                io 0x62 = 0x0066
                                                irq 0x70 = 0
                                        end
                                        device pnp 20e.12 on #  PM channel 2
                                                io 0x60 = 0x020c
                                                io 0x62 = 0x020d
                                                irq 0x70 = 0
                                        end
                                        device pnp 20e.17 off #  PM channel 3
                                        end
                                end     #ec/kontron/it8516e
                                # TODO: TPM on 4e
                        end # LPC bridge
                        device ref sata1 on end # SATA Controller 1
                        device ref smbus on end # SMBus
                        device ref sata2 off end # SATA Controller 2
                        device ref thermal off end # Thermal
                end
        end
end