drivers/tty/serial/8250/8250_lpc18xx.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Serial port driver for NXP LPC18xx/43xx UART
   4  *
   5  * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com>
   6  *
   7  * Based on 8250_mtk.c:
   8  * Copyright (c) 2014 MundoReader S.L.
   9  * Matthias Brugger <matthias.bgg@gmail.com>
  10  */
  11
  12 #include <linux/clk.h>
  13 #include <linux/io.h>
  14 #include <linux/module.h>
  15 #include <linux/of.h>
  16 #include <linux/platform_device.h>
  17
  18 #include "8250.h"
  19
  20 /* Additional LPC18xx/43xx 8250 registers and bits */
  21 #define LPC18XX_UART_RS485CTRL          (0x04c / sizeof(u32))
  22 #define  LPC18XX_UART_RS485CTRL_NMMEN   BIT(0)
  23 #define  LPC18XX_UART_RS485CTRL_DCTRL   BIT(4)
  24 #define  LPC18XX_UART_RS485CTRL_OINV    BIT(5)
  25 #define LPC18XX_UART_RS485DLY           (0x054 / sizeof(u32))
  26 #define LPC18XX_UART_RS485DLY_MAX       255
  27
  28 struct lpc18xx_uart_data {
  29         struct uart_8250_dma dma;
  30         struct clk *clk_uart;
  31         struct clk *clk_reg;
  32         int line;
  33 };
  34
  35 static int lpc18xx_rs485_config(struct uart_port *port,
  36                                 struct serial_rs485 *rs485)
  37 {
  38         struct uart_8250_port *up = up_to_u8250p(port);
  39         u32 rs485_ctrl_reg = 0;
  40         u32 rs485_dly_reg = 0;
  41         unsigned baud_clk;
  42
  43         if (rs485->flags & SER_RS485_ENABLED)
  44                 memset(rs485->padding, 0, sizeof(rs485->padding));
  45         else
  46                 memset(rs485, 0, sizeof(*rs485));
  47
  48         rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
  49                         SER_RS485_RTS_AFTER_SEND;
  50
  51         if (rs485->flags & SER_RS485_ENABLED) {
  52                 rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_NMMEN |
  53                                   LPC18XX_UART_RS485CTRL_DCTRL;
  54
  55                 if (rs485->flags & SER_RS485_RTS_ON_SEND) {
  56                         rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_OINV;
  57                         rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
  58                 } else {
  59                         rs485->flags |= SER_RS485_RTS_AFTER_SEND;
  60                 }
  61         }
  62
  63         if (rs485->delay_rts_after_send) {
  64                 baud_clk = port->uartclk / up->dl_read(up);
  65                 rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send
  66                                                 * baud_clk, MSEC_PER_SEC);
  67
  68                 if (rs485_dly_reg > LPC18XX_UART_RS485DLY_MAX)
  69                         rs485_dly_reg = LPC18XX_UART_RS485DLY_MAX;
  70
  71                 /* Calculate the resulting delay in ms */
  72                 rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC)
  73                                                 / baud_clk;
  74         }
  75
  76         /* Delay RTS before send not supported */
  77         rs485->delay_rts_before_send = 0;
  78
  79         serial_out(up, LPC18XX_UART_RS485CTRL, rs485_ctrl_reg);
  80         serial_out(up, LPC18XX_UART_RS485DLY, rs485_dly_reg);
  81
  82         port->rs485 = *rs485;
  83
  84         return 0;
  85 }
  86
  87 static void lpc18xx_uart_serial_out(struct uart_port *p, int offset, int value)
  88 {
  89         /*
  90          * For DMA mode one must ensure that the UART_FCR_DMA_SELECT
  91          * bit is set when FIFO is enabled. Even if DMA is not used
  92          * setting this bit doesn't seem to affect anything.
  93          */
  94         if (offset == UART_FCR && (value & UART_FCR_ENABLE_FIFO))
  95                 value |= UART_FCR_DMA_SELECT;
  96
  97         offset = offset << p->regshift;
  98         writel(value, p->membase + offset);
  99 }
 100
 101 static int lpc18xx_serial_probe(struct platform_device *pdev)
 102 {
 103         struct lpc18xx_uart_data *data;
 104         struct uart_8250_port uart;
 105         struct resource *res;
 106         int irq, ret;
 107
 108         irq = platform_get_irq(pdev, 0);
 109         if (irq < 0) {
 110                 dev_err(&pdev->dev, "irq not found");
 111                 return irq;
 112         }
 113
 114         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 115         if (!res) {
 116                 dev_err(&pdev->dev, "memory resource not found");
 117                 return -EINVAL;
 118         }
 119
 120         memset(&uart, 0, sizeof(uart));
 121
 122         uart.port.membase = devm_ioremap(&pdev->dev, res->start,
 123                                          resource_size(res));
 124         if (!uart.port.membase)
 125                 return -ENOMEM;
 126
 127         data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
 128         if (!data)
 129                 return -ENOMEM;
 130
 131         data->clk_uart = devm_clk_get(&pdev->dev, "uartclk");
 132         if (IS_ERR(data->clk_uart)) {
 133                 dev_err(&pdev->dev, "uart clock not found\n");
 134                 return PTR_ERR(data->clk_uart);
 135         }
 136
 137         data->clk_reg = devm_clk_get(&pdev->dev, "reg");
 138         if (IS_ERR(data->clk_reg)) {
 139                 dev_err(&pdev->dev, "reg clock not found\n");
 140                 return PTR_ERR(data->clk_reg);
 141         }
 142
 143         ret = clk_prepare_enable(data->clk_reg);
 144         if (ret) {
 145                 dev_err(&pdev->dev, "unable to enable reg clock\n");
 146                 return ret;
 147         }
 148
 149         ret = clk_prepare_enable(data->clk_uart);
 150         if (ret) {
 151                 dev_err(&pdev->dev, "unable to enable uart clock\n");
 152                 goto dis_clk_reg;
 153         }
 154
 155         ret = of_alias_get_id(pdev->dev.of_node, "serial");
 156         if (ret >= 0)
 157                 uart.port.line = ret;
 158
 159         data->dma.rx_param = data;
 160         data->dma.tx_param = data;
 161
 162         spin_lock_init(&uart.port.lock);
 163         uart.port.dev = &pdev->dev;
 164         uart.port.irq = irq;
 165         uart.port.iotype = UPIO_MEM32;
 166         uart.port.mapbase = res->start;
 167         uart.port.regshift = 2;
 168         uart.port.type = PORT_16550A;
 169         uart.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST;
 170         uart.port.uartclk = clk_get_rate(data->clk_uart);
 171         uart.port.private_data = data;
 172         uart.port.rs485_config = lpc18xx_rs485_config;
 173         uart.port.serial_out = lpc18xx_uart_serial_out;
 174
 175         uart.dma = &data->dma;
 176         uart.dma->rxconf.src_maxburst = 1;
 177         uart.dma->txconf.dst_maxburst = 1;
 178
 179         ret = serial8250_register_8250_port(&uart);
 180         if (ret < 0) {
 181                 dev_err(&pdev->dev, "unable to register 8250 port\n");
 182                 goto dis_uart_clk;
 183         }
 184
 185         data->line = ret;
 186         platform_set_drvdata(pdev, data);
 187
 188         return 0;
 189
 190 dis_uart_clk:
 191         clk_disable_unprepare(data->clk_uart);
 192 dis_clk_reg:
 193         clk_disable_unprepare(data->clk_reg);
 194         return ret;
 195 }
 196
 197 static int lpc18xx_serial_remove(struct platform_device *pdev)
 198 {
 199         struct lpc18xx_uart_data *data = platform_get_drvdata(pdev);
 200
 201         serial8250_unregister_port(data->line);
 202         clk_disable_unprepare(data->clk_uart);
 203         clk_disable_unprepare(data->clk_reg);
 204
 205         return 0;
 206 }
 207
 208 static const struct of_device_id lpc18xx_serial_match[] = {
 209         { .compatible = "nxp,lpc1850-uart" },
 210         { },
 211 };
 212 MODULE_DEVICE_TABLE(of, lpc18xx_serial_match);
 213
 214 static struct platform_driver lpc18xx_serial_driver = {
 215         .probe  = lpc18xx_serial_probe,
 216         .remove = lpc18xx_serial_remove,
 217         .driver = {
 218                 .name = "lpc18xx-uart",
 219                 .of_match_table = lpc18xx_serial_match,
 220         },
 221 };
 222 module_platform_driver(lpc18xx_serial_driver);
 223
 224 MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>");
 225 MODULE_DESCRIPTION("Serial port driver NXP LPC18xx/43xx devices");
 226 MODULE_LICENSE("GPL v2");