1 // SPDX-License-Identifier: GPL-2.0
3 * Copyright (C) 2014 Hauke Mehrtens <hauke@hauke-m.de>
4 * Copyright (C) 2015 Broadcom Corporation
7 #include <linux/kernel.h>
10 #include <linux/clk.h>
11 #include <linux/module.h>
12 #include <linux/mbus.h>
13 #include <linux/slab.h>
14 #include <linux/delay.h>
15 #include <linux/interrupt.h>
16 #include <linux/irqchip/arm-gic-v3.h>
17 #include <linux/platform_device.h>
18 #include <linux/of_address.h>
19 #include <linux/of_pci.h>
20 #include <linux/of_irq.h>
21 #include <linux/of_platform.h>
22 #include <linux/phy/phy.h>
24 #include "pcie-iproc.h"
26 #define EP_PERST_SOURCE_SELECT_SHIFT 2
27 #define EP_PERST_SOURCE_SELECT BIT(EP_PERST_SOURCE_SELECT_SHIFT)
28 #define EP_MODE_SURVIVE_PERST_SHIFT 1
29 #define EP_MODE_SURVIVE_PERST BIT(EP_MODE_SURVIVE_PERST_SHIFT)
30 #define RC_PCIE_RST_OUTPUT_SHIFT 0
31 #define RC_PCIE_RST_OUTPUT BIT(RC_PCIE_RST_OUTPUT_SHIFT)
32 #define PAXC_RESET_MASK 0x7f
34 #define GIC_V3_CFG_SHIFT 0
35 #define GIC_V3_CFG BIT(GIC_V3_CFG_SHIFT)
37 #define MSI_ENABLE_CFG_SHIFT 0
38 #define MSI_ENABLE_CFG BIT(MSI_ENABLE_CFG_SHIFT)
40 #define CFG_IND_ADDR_MASK 0x00001ffc
42 #define CFG_ADDR_BUS_NUM_SHIFT 20
43 #define CFG_ADDR_BUS_NUM_MASK 0x0ff00000
44 #define CFG_ADDR_DEV_NUM_SHIFT 15
45 #define CFG_ADDR_DEV_NUM_MASK 0x000f8000
46 #define CFG_ADDR_FUNC_NUM_SHIFT 12
47 #define CFG_ADDR_FUNC_NUM_MASK 0x00007000
48 #define CFG_ADDR_REG_NUM_SHIFT 2
49 #define CFG_ADDR_REG_NUM_MASK 0x00000ffc
50 #define CFG_ADDR_CFG_TYPE_SHIFT 0
51 #define CFG_ADDR_CFG_TYPE_MASK 0x00000003
53 #define SYS_RC_INTX_MASK 0xf
55 #define PCIE_PHYLINKUP_SHIFT 3
56 #define PCIE_PHYLINKUP BIT(PCIE_PHYLINKUP_SHIFT)
57 #define PCIE_DL_ACTIVE_SHIFT 2
58 #define PCIE_DL_ACTIVE BIT(PCIE_DL_ACTIVE_SHIFT)
60 #define APB_ERR_EN_SHIFT 0
61 #define APB_ERR_EN BIT(APB_ERR_EN_SHIFT)
63 #define CFG_RETRY_STATUS 0xffff0001
64 #define CFG_RETRY_STATUS_TIMEOUT_US 500000 /* 500 milliseconds */
66 /* derive the enum index of the outbound/inbound mapping registers */
67 #define MAP_REG(base_reg, index) ((base_reg) + (index) * 2)
70 * Maximum number of outbound mapping window sizes that can be supported by any
71 * OARR/OMAP mapping pair
73 #define MAX_NUM_OB_WINDOW_SIZES 4
75 #define OARR_VALID_SHIFT 0
76 #define OARR_VALID BIT(OARR_VALID_SHIFT)
77 #define OARR_SIZE_CFG_SHIFT 1
80 * Maximum number of inbound mapping region sizes that can be supported by an
83 #define MAX_NUM_IB_REGION_SIZES 9
85 #define IMAP_VALID_SHIFT 0
86 #define IMAP_VALID BIT(IMAP_VALID_SHIFT)
88 #define IPROC_PCI_EXP_CAP 0xac
90 #define IPROC_PCIE_REG_INVALID 0xffff
93 * iProc PCIe outbound mapping controller specific parameters
95 * @window_sizes: list of supported outbound mapping window sizes in MB
96 * @nr_sizes: number of supported outbound mapping window sizes
98 struct iproc_pcie_ob_map
{
99 resource_size_t window_sizes
[MAX_NUM_OB_WINDOW_SIZES
];
100 unsigned int nr_sizes
;
103 static const struct iproc_pcie_ob_map paxb_ob_map
[] = {
106 .window_sizes
= { 128, 256 },
111 .window_sizes
= { 128, 256 },
116 static const struct iproc_pcie_ob_map paxb_v2_ob_map
[] = {
119 .window_sizes
= { 128, 256 },
124 .window_sizes
= { 128, 256 },
129 .window_sizes
= { 128, 256, 512, 1024 },
134 .window_sizes
= { 128, 256, 512, 1024 },
140 * iProc PCIe inbound mapping type
142 enum iproc_pcie_ib_map_type
{
144 IPROC_PCIE_IB_MAP_MEM
= 0,
146 /* for device I/O memory */
147 IPROC_PCIE_IB_MAP_IO
,
149 /* invalid or unused */
150 IPROC_PCIE_IB_MAP_INVALID
154 * iProc PCIe inbound mapping controller specific parameters
156 * @type: inbound mapping region type
157 * @size_unit: inbound mapping region size unit, could be SZ_1K, SZ_1M, or
159 * @region_sizes: list of supported inbound mapping region sizes in KB, MB, or
160 * GB, depedning on the size unit
161 * @nr_sizes: number of supported inbound mapping region sizes
162 * @nr_windows: number of supported inbound mapping windows for the region
163 * @imap_addr_offset: register offset between the upper and lower 32-bit
164 * IMAP address registers
165 * @imap_window_offset: register offset between each IMAP window
167 struct iproc_pcie_ib_map
{
168 enum iproc_pcie_ib_map_type type
;
169 unsigned int size_unit
;
170 resource_size_t region_sizes
[MAX_NUM_IB_REGION_SIZES
];
171 unsigned int nr_sizes
;
172 unsigned int nr_windows
;
173 u16 imap_addr_offset
;
174 u16 imap_window_offset
;
177 static const struct iproc_pcie_ib_map paxb_v2_ib_map
[] = {
180 .type
= IPROC_PCIE_IB_MAP_IO
,
182 .region_sizes
= { 32 },
185 .imap_addr_offset
= 0x40,
186 .imap_window_offset
= 0x4,
189 /* IARR1/IMAP1 (currently unused) */
190 .type
= IPROC_PCIE_IB_MAP_INVALID
,
194 .type
= IPROC_PCIE_IB_MAP_MEM
,
196 .region_sizes
= { 64, 128, 256, 512, 1024, 2048, 4096, 8192,
200 .imap_addr_offset
= 0x4,
201 .imap_window_offset
= 0x8,
205 .type
= IPROC_PCIE_IB_MAP_MEM
,
207 .region_sizes
= { 1, 2, 4, 8, 16, 32 },
210 .imap_addr_offset
= 0x4,
211 .imap_window_offset
= 0x8,
215 .type
= IPROC_PCIE_IB_MAP_MEM
,
217 .region_sizes
= { 32, 64, 128, 256, 512 },
220 .imap_addr_offset
= 0x4,
221 .imap_window_offset
= 0x8,
226 * iProc PCIe host registers
228 enum iproc_pcie_reg
{
229 /* clock/reset signal control */
230 IPROC_PCIE_CLK_CTRL
= 0,
233 * To allow MSI to be steered to an external MSI controller (e.g., ARM
236 IPROC_PCIE_MSI_GIC_MODE
,
239 * IPROC_PCIE_MSI_BASE_ADDR and IPROC_PCIE_MSI_WINDOW_SIZE define the
240 * window where the MSI posted writes are written, for the writes to be
241 * interpreted as MSI writes.
243 IPROC_PCIE_MSI_BASE_ADDR
,
244 IPROC_PCIE_MSI_WINDOW_SIZE
,
247 * To hold the address of the register where the MSI writes are
248 * programed. When ARM GICv3 ITS is used, this should be programmed
249 * with the address of the GITS_TRANSLATER register.
251 IPROC_PCIE_MSI_ADDR_LO
,
252 IPROC_PCIE_MSI_ADDR_HI
,
255 IPROC_PCIE_MSI_EN_CFG
,
257 /* allow access to root complex configuration space */
258 IPROC_PCIE_CFG_IND_ADDR
,
259 IPROC_PCIE_CFG_IND_DATA
,
261 /* allow access to device configuration space */
268 /* outbound address mapping */
278 /* inbound address mapping */
291 IPROC_PCIE_LINK_STATUS
,
293 /* enable APB error for unsupported requests */
294 IPROC_PCIE_APB_ERR_EN
,
296 /* total number of core registers */
297 IPROC_PCIE_MAX_NUM_REG
,
300 /* iProc PCIe PAXB BCMA registers */
301 static const u16 iproc_pcie_reg_paxb_bcma
[] = {
302 [IPROC_PCIE_CLK_CTRL
] = 0x000,
303 [IPROC_PCIE_CFG_IND_ADDR
] = 0x120,
304 [IPROC_PCIE_CFG_IND_DATA
] = 0x124,
305 [IPROC_PCIE_CFG_ADDR
] = 0x1f8,
306 [IPROC_PCIE_CFG_DATA
] = 0x1fc,
307 [IPROC_PCIE_INTX_EN
] = 0x330,
308 [IPROC_PCIE_LINK_STATUS
] = 0xf0c,
311 /* iProc PCIe PAXB registers */
312 static const u16 iproc_pcie_reg_paxb
[] = {
313 [IPROC_PCIE_CLK_CTRL
] = 0x000,
314 [IPROC_PCIE_CFG_IND_ADDR
] = 0x120,
315 [IPROC_PCIE_CFG_IND_DATA
] = 0x124,
316 [IPROC_PCIE_CFG_ADDR
] = 0x1f8,
317 [IPROC_PCIE_CFG_DATA
] = 0x1fc,
318 [IPROC_PCIE_INTX_EN
] = 0x330,
319 [IPROC_PCIE_OARR0
] = 0xd20,
320 [IPROC_PCIE_OMAP0
] = 0xd40,
321 [IPROC_PCIE_OARR1
] = 0xd28,
322 [IPROC_PCIE_OMAP1
] = 0xd48,
323 [IPROC_PCIE_LINK_STATUS
] = 0xf0c,
324 [IPROC_PCIE_APB_ERR_EN
] = 0xf40,
327 /* iProc PCIe PAXB v2 registers */
328 static const u16 iproc_pcie_reg_paxb_v2
[] = {
329 [IPROC_PCIE_CLK_CTRL
] = 0x000,
330 [IPROC_PCIE_CFG_IND_ADDR
] = 0x120,
331 [IPROC_PCIE_CFG_IND_DATA
] = 0x124,
332 [IPROC_PCIE_CFG_ADDR
] = 0x1f8,
333 [IPROC_PCIE_CFG_DATA
] = 0x1fc,
334 [IPROC_PCIE_INTX_EN
] = 0x330,
335 [IPROC_PCIE_OARR0
] = 0xd20,
336 [IPROC_PCIE_OMAP0
] = 0xd40,
337 [IPROC_PCIE_OARR1
] = 0xd28,
338 [IPROC_PCIE_OMAP1
] = 0xd48,
339 [IPROC_PCIE_OARR2
] = 0xd60,
340 [IPROC_PCIE_OMAP2
] = 0xd68,
341 [IPROC_PCIE_OARR3
] = 0xdf0,
342 [IPROC_PCIE_OMAP3
] = 0xdf8,
343 [IPROC_PCIE_IARR0
] = 0xd00,
344 [IPROC_PCIE_IMAP0
] = 0xc00,
345 [IPROC_PCIE_IARR2
] = 0xd10,
346 [IPROC_PCIE_IMAP2
] = 0xcc0,
347 [IPROC_PCIE_IARR3
] = 0xe00,
348 [IPROC_PCIE_IMAP3
] = 0xe08,
349 [IPROC_PCIE_IARR4
] = 0xe68,
350 [IPROC_PCIE_IMAP4
] = 0xe70,
351 [IPROC_PCIE_LINK_STATUS
] = 0xf0c,
352 [IPROC_PCIE_APB_ERR_EN
] = 0xf40,
355 /* iProc PCIe PAXC v1 registers */
356 static const u16 iproc_pcie_reg_paxc
[] = {
357 [IPROC_PCIE_CLK_CTRL
] = 0x000,
358 [IPROC_PCIE_CFG_IND_ADDR
] = 0x1f0,
359 [IPROC_PCIE_CFG_IND_DATA
] = 0x1f4,
360 [IPROC_PCIE_CFG_ADDR
] = 0x1f8,
361 [IPROC_PCIE_CFG_DATA
] = 0x1fc,
364 /* iProc PCIe PAXC v2 registers */
365 static const u16 iproc_pcie_reg_paxc_v2
[] = {
366 [IPROC_PCIE_MSI_GIC_MODE
] = 0x050,
367 [IPROC_PCIE_MSI_BASE_ADDR
] = 0x074,
368 [IPROC_PCIE_MSI_WINDOW_SIZE
] = 0x078,
369 [IPROC_PCIE_MSI_ADDR_LO
] = 0x07c,
370 [IPROC_PCIE_MSI_ADDR_HI
] = 0x080,
371 [IPROC_PCIE_MSI_EN_CFG
] = 0x09c,
372 [IPROC_PCIE_CFG_IND_ADDR
] = 0x1f0,
373 [IPROC_PCIE_CFG_IND_DATA
] = 0x1f4,
374 [IPROC_PCIE_CFG_ADDR
] = 0x1f8,
375 [IPROC_PCIE_CFG_DATA
] = 0x1fc,
378 static inline struct iproc_pcie
*iproc_data(struct pci_bus
*bus
)
380 struct iproc_pcie
*pcie
;
382 struct pci_sys_data
*sys
= bus
->sysdata
;
384 pcie
= sys
->private_data
;
391 static inline bool iproc_pcie_reg_is_invalid(u16 reg_offset
)
393 return !!(reg_offset
== IPROC_PCIE_REG_INVALID
);
396 static inline u16
iproc_pcie_reg_offset(struct iproc_pcie
*pcie
,
397 enum iproc_pcie_reg reg
)
399 return pcie
->reg_offsets
[reg
];
402 static inline u32
iproc_pcie_read_reg(struct iproc_pcie
*pcie
,
403 enum iproc_pcie_reg reg
)
405 u16 offset
= iproc_pcie_reg_offset(pcie
, reg
);
407 if (iproc_pcie_reg_is_invalid(offset
))
410 return readl(pcie
->base
+ offset
);
413 static inline void iproc_pcie_write_reg(struct iproc_pcie
*pcie
,
414 enum iproc_pcie_reg reg
, u32 val
)
416 u16 offset
= iproc_pcie_reg_offset(pcie
, reg
);
418 if (iproc_pcie_reg_is_invalid(offset
))
421 writel(val
, pcie
->base
+ offset
);
425 * APB error forwarding can be disabled during access of configuration
426 * registers of the endpoint device, to prevent unsupported requests
427 * (typically seen during enumeration with multi-function devices) from
428 * triggering a system exception.
430 static inline void iproc_pcie_apb_err_disable(struct pci_bus
*bus
,
433 struct iproc_pcie
*pcie
= iproc_data(bus
);
436 if (bus
->number
&& pcie
->has_apb_err_disable
) {
437 val
= iproc_pcie_read_reg(pcie
, IPROC_PCIE_APB_ERR_EN
);
442 iproc_pcie_write_reg(pcie
, IPROC_PCIE_APB_ERR_EN
, val
);
446 static void __iomem
*iproc_pcie_map_ep_cfg_reg(struct iproc_pcie
*pcie
,
455 /* EP device access */
456 val
= (busno
<< CFG_ADDR_BUS_NUM_SHIFT
) |
457 (slot
<< CFG_ADDR_DEV_NUM_SHIFT
) |
458 (fn
<< CFG_ADDR_FUNC_NUM_SHIFT
) |
459 (where
& CFG_ADDR_REG_NUM_MASK
) |
460 (1 & CFG_ADDR_CFG_TYPE_MASK
);
462 iproc_pcie_write_reg(pcie
, IPROC_PCIE_CFG_ADDR
, val
);
463 offset
= iproc_pcie_reg_offset(pcie
, IPROC_PCIE_CFG_DATA
);
465 if (iproc_pcie_reg_is_invalid(offset
))
468 return (pcie
->base
+ offset
);
471 static unsigned int iproc_pcie_cfg_retry(void __iomem
*cfg_data_p
)
473 int timeout
= CFG_RETRY_STATUS_TIMEOUT_US
;
477 * As per PCIe spec r3.1, sec 2.3.2, CRS Software Visibility only
478 * affects config reads of the Vendor ID. For config writes or any
479 * other config reads, the Root may automatically reissue the
480 * configuration request again as a new request.
482 * For config reads, this hardware returns CFG_RETRY_STATUS data
483 * when it receives a CRS completion, regardless of the address of
484 * the read or the CRS Software Visibility Enable bit. As a
485 * partial workaround for this, we retry in software any read that
486 * returns CFG_RETRY_STATUS.
488 * Note that a non-Vendor ID config register may have a value of
489 * CFG_RETRY_STATUS. If we read that, we can't distinguish it from
490 * a CRS completion, so we will incorrectly retry the read and
491 * eventually return the wrong data (0xffffffff).
493 data
= readl(cfg_data_p
);
494 while (data
== CFG_RETRY_STATUS
&& timeout
--) {
496 data
= readl(cfg_data_p
);
499 if (data
== CFG_RETRY_STATUS
)
505 static int iproc_pcie_config_read(struct pci_bus
*bus
, unsigned int devfn
,
506 int where
, int size
, u32
*val
)
508 struct iproc_pcie
*pcie
= iproc_data(bus
);
509 unsigned int slot
= PCI_SLOT(devfn
);
510 unsigned int fn
= PCI_FUNC(devfn
);
511 unsigned int busno
= bus
->number
;
512 void __iomem
*cfg_data_p
;
516 /* root complex access */
518 ret
= pci_generic_config_read32(bus
, devfn
, where
, size
, val
);
519 if (ret
!= PCIBIOS_SUCCESSFUL
)
522 /* Don't advertise CRS SV support */
523 if ((where
& ~0x3) == IPROC_PCI_EXP_CAP
+ PCI_EXP_RTCTL
)
524 *val
&= ~(PCI_EXP_RTCAP_CRSVIS
<< 16);
525 return PCIBIOS_SUCCESSFUL
;
528 cfg_data_p
= iproc_pcie_map_ep_cfg_reg(pcie
, busno
, slot
, fn
, where
);
531 return PCIBIOS_DEVICE_NOT_FOUND
;
533 data
= iproc_pcie_cfg_retry(cfg_data_p
);
537 *val
= (data
>> (8 * (where
& 3))) & ((1 << (size
* 8)) - 1);
539 return PCIBIOS_SUCCESSFUL
;
543 * Note access to the configuration registers are protected at the higher layer
544 * by 'pci_lock' in drivers/pci/access.c
546 static void __iomem
*iproc_pcie_map_cfg_bus(struct iproc_pcie
*pcie
,
547 int busno
, unsigned int devfn
,
550 unsigned slot
= PCI_SLOT(devfn
);
551 unsigned fn
= PCI_FUNC(devfn
);
554 /* root complex access */
556 if (slot
> 0 || fn
> 0)
559 iproc_pcie_write_reg(pcie
, IPROC_PCIE_CFG_IND_ADDR
,
560 where
& CFG_IND_ADDR_MASK
);
561 offset
= iproc_pcie_reg_offset(pcie
, IPROC_PCIE_CFG_IND_DATA
);
562 if (iproc_pcie_reg_is_invalid(offset
))
565 return (pcie
->base
+ offset
);
569 * PAXC is connected to an internally emulated EP within the SoC. It
570 * allows only one device.
572 if (pcie
->ep_is_internal
)
576 return iproc_pcie_map_ep_cfg_reg(pcie
, busno
, slot
, fn
, where
);
579 static void __iomem
*iproc_pcie_bus_map_cfg_bus(struct pci_bus
*bus
,
583 return iproc_pcie_map_cfg_bus(iproc_data(bus
), bus
->number
, devfn
,
587 static int iproc_pci_raw_config_read32(struct iproc_pcie
*pcie
,
588 unsigned int devfn
, int where
,
593 addr
= iproc_pcie_map_cfg_bus(pcie
, 0, devfn
, where
& ~0x3);
596 return PCIBIOS_DEVICE_NOT_FOUND
;
602 *val
= (*val
>> (8 * (where
& 3))) & ((1 << (size
* 8)) - 1);
604 return PCIBIOS_SUCCESSFUL
;
607 static int iproc_pci_raw_config_write32(struct iproc_pcie
*pcie
,
608 unsigned int devfn
, int where
,
614 addr
= iproc_pcie_map_cfg_bus(pcie
, 0, devfn
, where
& ~0x3);
616 return PCIBIOS_DEVICE_NOT_FOUND
;
620 return PCIBIOS_SUCCESSFUL
;
623 mask
= ~(((1 << (size
* 8)) - 1) << ((where
& 0x3) * 8));
624 tmp
= readl(addr
) & mask
;
625 tmp
|= val
<< ((where
& 0x3) * 8);
628 return PCIBIOS_SUCCESSFUL
;
631 static int iproc_pcie_config_read32(struct pci_bus
*bus
, unsigned int devfn
,
632 int where
, int size
, u32
*val
)
635 struct iproc_pcie
*pcie
= iproc_data(bus
);
637 iproc_pcie_apb_err_disable(bus
, true);
638 if (pcie
->type
== IPROC_PCIE_PAXB_V2
)
639 ret
= iproc_pcie_config_read(bus
, devfn
, where
, size
, val
);
641 ret
= pci_generic_config_read32(bus
, devfn
, where
, size
, val
);
642 iproc_pcie_apb_err_disable(bus
, false);
647 static int iproc_pcie_config_write32(struct pci_bus
*bus
, unsigned int devfn
,
648 int where
, int size
, u32 val
)
652 iproc_pcie_apb_err_disable(bus
, true);
653 ret
= pci_generic_config_write32(bus
, devfn
, where
, size
, val
);
654 iproc_pcie_apb_err_disable(bus
, false);
659 static struct pci_ops iproc_pcie_ops
= {
660 .map_bus
= iproc_pcie_bus_map_cfg_bus
,
661 .read
= iproc_pcie_config_read32
,
662 .write
= iproc_pcie_config_write32
,
665 static void iproc_pcie_perst_ctrl(struct iproc_pcie
*pcie
, bool assert)
670 * PAXC and the internal emulated endpoint device downstream should not
671 * be reset. If firmware has been loaded on the endpoint device at an
672 * earlier boot stage, reset here causes issues.
674 if (pcie
->ep_is_internal
)
678 val
= iproc_pcie_read_reg(pcie
, IPROC_PCIE_CLK_CTRL
);
679 val
&= ~EP_PERST_SOURCE_SELECT
& ~EP_MODE_SURVIVE_PERST
&
681 iproc_pcie_write_reg(pcie
, IPROC_PCIE_CLK_CTRL
, val
);
684 val
= iproc_pcie_read_reg(pcie
, IPROC_PCIE_CLK_CTRL
);
685 val
|= RC_PCIE_RST_OUTPUT
;
686 iproc_pcie_write_reg(pcie
, IPROC_PCIE_CLK_CTRL
, val
);
691 int iproc_pcie_shutdown(struct iproc_pcie
*pcie
)
693 iproc_pcie_perst_ctrl(pcie
, true);
698 EXPORT_SYMBOL_GPL(iproc_pcie_shutdown
);
700 static int iproc_pcie_check_link(struct iproc_pcie
*pcie
)
702 struct device
*dev
= pcie
->dev
;
703 u32 hdr_type
, link_ctrl
, link_status
, class, val
;
704 bool link_is_active
= false;
707 * PAXC connects to emulated endpoint devices directly and does not
708 * have a Serdes. Therefore skip the link detection logic here.
710 if (pcie
->ep_is_internal
)
713 val
= iproc_pcie_read_reg(pcie
, IPROC_PCIE_LINK_STATUS
);
714 if (!(val
& PCIE_PHYLINKUP
) || !(val
& PCIE_DL_ACTIVE
)) {
715 dev_err(dev
, "PHY or data link is INACTIVE!\n");
719 /* make sure we are not in EP mode */
720 iproc_pci_raw_config_read32(pcie
, 0, PCI_HEADER_TYPE
, 1, &hdr_type
);
721 if ((hdr_type
& 0x7f) != PCI_HEADER_TYPE_BRIDGE
) {
722 dev_err(dev
, "in EP mode, hdr=%#02x\n", hdr_type
);
726 /* force class to PCI_CLASS_BRIDGE_PCI (0x0604) */
727 #define PCI_BRIDGE_CTRL_REG_OFFSET 0x43c
728 #define PCI_CLASS_BRIDGE_MASK 0xffff00
729 #define PCI_CLASS_BRIDGE_SHIFT 8
730 iproc_pci_raw_config_read32(pcie
, 0, PCI_BRIDGE_CTRL_REG_OFFSET
,
732 class &= ~PCI_CLASS_BRIDGE_MASK
;
733 class |= (PCI_CLASS_BRIDGE_PCI
<< PCI_CLASS_BRIDGE_SHIFT
);
734 iproc_pci_raw_config_write32(pcie
, 0, PCI_BRIDGE_CTRL_REG_OFFSET
,
737 /* check link status to see if link is active */
738 iproc_pci_raw_config_read32(pcie
, 0, IPROC_PCI_EXP_CAP
+ PCI_EXP_LNKSTA
,
740 if (link_status
& PCI_EXP_LNKSTA_NLW
)
741 link_is_active
= true;
743 if (!link_is_active
) {
744 /* try GEN 1 link speed */
745 #define PCI_TARGET_LINK_SPEED_MASK 0xf
746 #define PCI_TARGET_LINK_SPEED_GEN2 0x2
747 #define PCI_TARGET_LINK_SPEED_GEN1 0x1
748 iproc_pci_raw_config_read32(pcie
, 0,
749 IPROC_PCI_EXP_CAP
+ PCI_EXP_LNKCTL2
,
751 if ((link_ctrl
& PCI_TARGET_LINK_SPEED_MASK
) ==
752 PCI_TARGET_LINK_SPEED_GEN2
) {
753 link_ctrl
&= ~PCI_TARGET_LINK_SPEED_MASK
;
754 link_ctrl
|= PCI_TARGET_LINK_SPEED_GEN1
;
755 iproc_pci_raw_config_write32(pcie
, 0,
756 IPROC_PCI_EXP_CAP
+ PCI_EXP_LNKCTL2
,
760 iproc_pci_raw_config_read32(pcie
, 0,
761 IPROC_PCI_EXP_CAP
+ PCI_EXP_LNKSTA
,
763 if (link_status
& PCI_EXP_LNKSTA_NLW
)
764 link_is_active
= true;
768 dev_info(dev
, "link: %s\n", link_is_active
? "UP" : "DOWN");
770 return link_is_active
? 0 : -ENODEV
;
773 static void iproc_pcie_enable(struct iproc_pcie
*pcie
)
775 iproc_pcie_write_reg(pcie
, IPROC_PCIE_INTX_EN
, SYS_RC_INTX_MASK
);
778 static inline bool iproc_pcie_ob_is_valid(struct iproc_pcie
*pcie
,
783 val
= iproc_pcie_read_reg(pcie
, MAP_REG(IPROC_PCIE_OARR0
, window_idx
));
785 return !!(val
& OARR_VALID
);
788 static inline int iproc_pcie_ob_write(struct iproc_pcie
*pcie
, int window_idx
,
789 int size_idx
, u64 axi_addr
, u64 pci_addr
)
791 struct device
*dev
= pcie
->dev
;
792 u16 oarr_offset
, omap_offset
;
795 * Derive the OARR/OMAP offset from the first pair (OARR0/OMAP0) based
798 oarr_offset
= iproc_pcie_reg_offset(pcie
, MAP_REG(IPROC_PCIE_OARR0
,
800 omap_offset
= iproc_pcie_reg_offset(pcie
, MAP_REG(IPROC_PCIE_OMAP0
,
802 if (iproc_pcie_reg_is_invalid(oarr_offset
) ||
803 iproc_pcie_reg_is_invalid(omap_offset
))
807 * Program the OARR registers. The upper 32-bit OARR register is
808 * always right after the lower 32-bit OARR register.
810 writel(lower_32_bits(axi_addr
) | (size_idx
<< OARR_SIZE_CFG_SHIFT
) |
811 OARR_VALID
, pcie
->base
+ oarr_offset
);
812 writel(upper_32_bits(axi_addr
), pcie
->base
+ oarr_offset
+ 4);
814 /* now program the OMAP registers */
815 writel(lower_32_bits(pci_addr
), pcie
->base
+ omap_offset
);
816 writel(upper_32_bits(pci_addr
), pcie
->base
+ omap_offset
+ 4);
818 dev_info(dev
, "ob window [%d]: offset 0x%x axi %pap pci %pap\n",
819 window_idx
, oarr_offset
, &axi_addr
, &pci_addr
);
820 dev_info(dev
, "oarr lo 0x%x oarr hi 0x%x\n",
821 readl(pcie
->base
+ oarr_offset
),
822 readl(pcie
->base
+ oarr_offset
+ 4));
823 dev_info(dev
, "omap lo 0x%x omap hi 0x%x\n",
824 readl(pcie
->base
+ omap_offset
),
825 readl(pcie
->base
+ omap_offset
+ 4));
831 * Some iProc SoCs require the SW to configure the outbound address mapping
833 * Outbound address translation:
835 * iproc_pcie_address = axi_address - axi_offset
836 * OARR = iproc_pcie_address
839 * axi_addr -> iproc_pcie_address -> OARR -> OMAP -> pci_address
841 static int iproc_pcie_setup_ob(struct iproc_pcie
*pcie
, u64 axi_addr
,
842 u64 pci_addr
, resource_size_t size
)
844 struct iproc_pcie_ob
*ob
= &pcie
->ob
;
845 struct device
*dev
= pcie
->dev
;
846 int ret
= -EINVAL
, window_idx
, size_idx
;
848 if (axi_addr
< ob
->axi_offset
) {
849 dev_err(dev
, "axi address %pap less than offset %pap\n",
850 &axi_addr
, &ob
->axi_offset
);
855 * Translate the AXI address to the internal address used by the iProc
856 * PCIe core before programming the OARR
858 axi_addr
-= ob
->axi_offset
;
860 /* iterate through all OARR/OMAP mapping windows */
861 for (window_idx
= ob
->nr_windows
- 1; window_idx
>= 0; window_idx
--) {
862 const struct iproc_pcie_ob_map
*ob_map
=
863 &pcie
->ob_map
[window_idx
];
866 * If current outbound window is already in use, move on to the
869 if (iproc_pcie_ob_is_valid(pcie
, window_idx
))
873 * Iterate through all supported window sizes within the
874 * OARR/OMAP pair to find a match. Go through the window sizes
875 * in a descending order.
877 for (size_idx
= ob_map
->nr_sizes
- 1; size_idx
>= 0;
879 resource_size_t window_size
=
880 ob_map
->window_sizes
[size_idx
] * SZ_1M
;
882 if (size
< window_size
)
885 if (!IS_ALIGNED(axi_addr
, window_size
) ||
886 !IS_ALIGNED(pci_addr
, window_size
)) {
888 "axi %pap or pci %pap not aligned\n",
889 &axi_addr
, &pci_addr
);
894 * Match found! Program both OARR and OMAP and mark
895 * them as a valid entry.
897 ret
= iproc_pcie_ob_write(pcie
, window_idx
, size_idx
,
907 * If we are here, we are done with the current window,
908 * but not yet finished all mappings. Need to move on
909 * to the next window.
911 axi_addr
+= window_size
;
912 pci_addr
+= window_size
;
918 dev_err(dev
, "unable to configure outbound mapping\n");
920 "axi %pap, axi offset %pap, pci %pap, res size %pap\n",
921 &axi_addr
, &ob
->axi_offset
, &pci_addr
, &size
);
926 static int iproc_pcie_map_ranges(struct iproc_pcie
*pcie
,
927 struct list_head
*resources
)
929 struct device
*dev
= pcie
->dev
;
930 struct resource_entry
*window
;
933 resource_list_for_each_entry(window
, resources
) {
934 struct resource
*res
= window
->res
;
935 u64 res_type
= resource_type(res
);
942 ret
= iproc_pcie_setup_ob(pcie
, res
->start
,
943 res
->start
- window
->offset
,
949 dev_err(dev
, "invalid resource %pR\n", res
);
957 static inline bool iproc_pcie_ib_is_in_use(struct iproc_pcie
*pcie
,
960 const struct iproc_pcie_ib_map
*ib_map
= &pcie
->ib_map
[region_idx
];
963 val
= iproc_pcie_read_reg(pcie
, MAP_REG(IPROC_PCIE_IARR0
, region_idx
));
965 return !!(val
& (BIT(ib_map
->nr_sizes
) - 1));
968 static inline bool iproc_pcie_ib_check_type(const struct iproc_pcie_ib_map
*ib_map
,
969 enum iproc_pcie_ib_map_type type
)
971 return !!(ib_map
->type
== type
);
974 static int iproc_pcie_ib_write(struct iproc_pcie
*pcie
, int region_idx
,
975 int size_idx
, int nr_windows
, u64 axi_addr
,
976 u64 pci_addr
, resource_size_t size
)
978 struct device
*dev
= pcie
->dev
;
979 const struct iproc_pcie_ib_map
*ib_map
= &pcie
->ib_map
[region_idx
];
980 u16 iarr_offset
, imap_offset
;
984 iarr_offset
= iproc_pcie_reg_offset(pcie
,
985 MAP_REG(IPROC_PCIE_IARR0
, region_idx
));
986 imap_offset
= iproc_pcie_reg_offset(pcie
,
987 MAP_REG(IPROC_PCIE_IMAP0
, region_idx
));
988 if (iproc_pcie_reg_is_invalid(iarr_offset
) ||
989 iproc_pcie_reg_is_invalid(imap_offset
))
992 dev_info(dev
, "ib region [%d]: offset 0x%x axi %pap pci %pap\n",
993 region_idx
, iarr_offset
, &axi_addr
, &pci_addr
);
996 * Program the IARR registers. The upper 32-bit IARR register is
997 * always right after the lower 32-bit IARR register.
999 writel(lower_32_bits(pci_addr
) | BIT(size_idx
),
1000 pcie
->base
+ iarr_offset
);
1001 writel(upper_32_bits(pci_addr
), pcie
->base
+ iarr_offset
+ 4);
1003 dev_info(dev
, "iarr lo 0x%x iarr hi 0x%x\n",
1004 readl(pcie
->base
+ iarr_offset
),
1005 readl(pcie
->base
+ iarr_offset
+ 4));
1008 * Now program the IMAP registers. Each IARR region may have one or
1009 * more IMAP windows.
1011 size
>>= ilog2(nr_windows
);
1012 for (window_idx
= 0; window_idx
< nr_windows
; window_idx
++) {
1013 val
= readl(pcie
->base
+ imap_offset
);
1014 val
|= lower_32_bits(axi_addr
) | IMAP_VALID
;
1015 writel(val
, pcie
->base
+ imap_offset
);
1016 writel(upper_32_bits(axi_addr
),
1017 pcie
->base
+ imap_offset
+ ib_map
->imap_addr_offset
);
1019 dev_info(dev
, "imap window [%d] lo 0x%x hi 0x%x\n",
1020 window_idx
, readl(pcie
->base
+ imap_offset
),
1021 readl(pcie
->base
+ imap_offset
+
1022 ib_map
->imap_addr_offset
));
1024 imap_offset
+= ib_map
->imap_window_offset
;
1031 static int iproc_pcie_setup_ib(struct iproc_pcie
*pcie
,
1032 struct of_pci_range
*range
,
1033 enum iproc_pcie_ib_map_type type
)
1035 struct device
*dev
= pcie
->dev
;
1036 struct iproc_pcie_ib
*ib
= &pcie
->ib
;
1038 unsigned int region_idx
, size_idx
;
1039 u64 axi_addr
= range
->cpu_addr
, pci_addr
= range
->pci_addr
;
1040 resource_size_t size
= range
->size
;
1042 /* iterate through all IARR mapping regions */
1043 for (region_idx
= 0; region_idx
< ib
->nr_regions
; region_idx
++) {
1044 const struct iproc_pcie_ib_map
*ib_map
=
1045 &pcie
->ib_map
[region_idx
];
1048 * If current inbound region is already in use or not a
1049 * compatible type, move on to the next.
1051 if (iproc_pcie_ib_is_in_use(pcie
, region_idx
) ||
1052 !iproc_pcie_ib_check_type(ib_map
, type
))
1055 /* iterate through all supported region sizes to find a match */
1056 for (size_idx
= 0; size_idx
< ib_map
->nr_sizes
; size_idx
++) {
1057 resource_size_t region_size
=
1058 ib_map
->region_sizes
[size_idx
] * ib_map
->size_unit
;
1060 if (size
!= region_size
)
1063 if (!IS_ALIGNED(axi_addr
, region_size
) ||
1064 !IS_ALIGNED(pci_addr
, region_size
)) {
1066 "axi %pap or pci %pap not aligned\n",
1067 &axi_addr
, &pci_addr
);
1071 /* Match found! Program IARR and all IMAP windows. */
1072 ret
= iproc_pcie_ib_write(pcie
, region_idx
, size_idx
,
1073 ib_map
->nr_windows
, axi_addr
,
1085 dev_err(dev
, "unable to configure inbound mapping\n");
1086 dev_err(dev
, "axi %pap, pci %pap, res size %pap\n",
1087 &axi_addr
, &pci_addr
, &size
);
1092 static int iproc_pcie_map_dma_ranges(struct iproc_pcie
*pcie
)
1094 struct of_pci_range range
;
1095 struct of_pci_range_parser parser
;
1098 /* Get the dma-ranges from DT */
1099 ret
= of_pci_dma_range_parser_init(&parser
, pcie
->dev
->of_node
);
1103 for_each_of_pci_range(&parser
, &range
) {
1104 /* Each range entry corresponds to an inbound mapping region */
1105 ret
= iproc_pcie_setup_ib(pcie
, &range
, IPROC_PCIE_IB_MAP_MEM
);
1113 static int iproce_pcie_get_msi(struct iproc_pcie
*pcie
,
1114 struct device_node
*msi_node
,
1117 struct device
*dev
= pcie
->dev
;
1119 struct resource res
;
1122 * Check if 'msi-map' points to ARM GICv3 ITS, which is the only
1123 * supported external MSI controller that requires steering.
1125 if (!of_device_is_compatible(msi_node
, "arm,gic-v3-its")) {
1126 dev_err(dev
, "unable to find compatible MSI controller\n");
1130 /* derive GITS_TRANSLATER address from GICv3 */
1131 ret
= of_address_to_resource(msi_node
, 0, &res
);
1133 dev_err(dev
, "unable to obtain MSI controller resources\n");
1137 *msi_addr
= res
.start
+ GITS_TRANSLATER
;
1141 static int iproc_pcie_paxb_v2_msi_steer(struct iproc_pcie
*pcie
, u64 msi_addr
)
1144 struct of_pci_range range
;
1146 memset(&range
, 0, sizeof(range
));
1147 range
.size
= SZ_32K
;
1148 range
.pci_addr
= range
.cpu_addr
= msi_addr
& ~(range
.size
- 1);
1150 ret
= iproc_pcie_setup_ib(pcie
, &range
, IPROC_PCIE_IB_MAP_IO
);
1154 static void iproc_pcie_paxc_v2_msi_steer(struct iproc_pcie
*pcie
, u64 msi_addr
)
1159 * Program bits [43:13] of address of GITS_TRANSLATER register into
1160 * bits [30:0] of the MSI base address register. In fact, in all iProc
1161 * based SoCs, all I/O register bases are well below the 32-bit
1162 * boundary, so we can safely assume bits [43:32] are always zeros.
1164 iproc_pcie_write_reg(pcie
, IPROC_PCIE_MSI_BASE_ADDR
,
1165 (u32
)(msi_addr
>> 13));
1167 /* use a default 8K window size */
1168 iproc_pcie_write_reg(pcie
, IPROC_PCIE_MSI_WINDOW_SIZE
, 0);
1170 /* steering MSI to GICv3 ITS */
1171 val
= iproc_pcie_read_reg(pcie
, IPROC_PCIE_MSI_GIC_MODE
);
1173 iproc_pcie_write_reg(pcie
, IPROC_PCIE_MSI_GIC_MODE
, val
);
1176 * Program bits [43:2] of address of GITS_TRANSLATER register into the
1177 * iProc MSI address registers.
1180 iproc_pcie_write_reg(pcie
, IPROC_PCIE_MSI_ADDR_HI
,
1181 upper_32_bits(msi_addr
));
1182 iproc_pcie_write_reg(pcie
, IPROC_PCIE_MSI_ADDR_LO
,
1183 lower_32_bits(msi_addr
));
1186 val
= iproc_pcie_read_reg(pcie
, IPROC_PCIE_MSI_EN_CFG
);
1187 val
|= MSI_ENABLE_CFG
;
1188 iproc_pcie_write_reg(pcie
, IPROC_PCIE_MSI_EN_CFG
, val
);
1191 static int iproc_pcie_msi_steer(struct iproc_pcie
*pcie
,
1192 struct device_node
*msi_node
)
1194 struct device
*dev
= pcie
->dev
;
1198 ret
= iproce_pcie_get_msi(pcie
, msi_node
, &msi_addr
);
1200 dev_err(dev
, "msi steering failed\n");
1204 switch (pcie
->type
) {
1205 case IPROC_PCIE_PAXB_V2
:
1206 ret
= iproc_pcie_paxb_v2_msi_steer(pcie
, msi_addr
);
1210 case IPROC_PCIE_PAXC_V2
:
1211 iproc_pcie_paxc_v2_msi_steer(pcie
, msi_addr
);
1220 static int iproc_pcie_msi_enable(struct iproc_pcie
*pcie
)
1222 struct device_node
*msi_node
;
1226 * Either the "msi-parent" or the "msi-map" phandle needs to exist
1227 * for us to obtain the MSI node.
1230 msi_node
= of_parse_phandle(pcie
->dev
->of_node
, "msi-parent", 0);
1232 const __be32
*msi_map
= NULL
;
1236 msi_map
= of_get_property(pcie
->dev
->of_node
, "msi-map", &len
);
1240 phandle
= be32_to_cpup(msi_map
+ 1);
1241 msi_node
= of_find_node_by_phandle(phandle
);
1247 * Certain revisions of the iProc PCIe controller require additional
1248 * configurations to steer the MSI writes towards an external MSI
1251 if (pcie
->need_msi_steer
) {
1252 ret
= iproc_pcie_msi_steer(pcie
, msi_node
);
1258 * If another MSI controller is being used, the call below should fail
1261 return iproc_msi_init(pcie
, msi_node
);
1264 static void iproc_pcie_msi_disable(struct iproc_pcie
*pcie
)
1266 iproc_msi_exit(pcie
);
1269 static int iproc_pcie_rev_init(struct iproc_pcie
*pcie
)
1271 struct device
*dev
= pcie
->dev
;
1272 unsigned int reg_idx
;
1275 switch (pcie
->type
) {
1276 case IPROC_PCIE_PAXB_BCMA
:
1277 regs
= iproc_pcie_reg_paxb_bcma
;
1279 case IPROC_PCIE_PAXB
:
1280 regs
= iproc_pcie_reg_paxb
;
1281 pcie
->has_apb_err_disable
= true;
1282 if (pcie
->need_ob_cfg
) {
1283 pcie
->ob_map
= paxb_ob_map
;
1284 pcie
->ob
.nr_windows
= ARRAY_SIZE(paxb_ob_map
);
1287 case IPROC_PCIE_PAXB_V2
:
1288 regs
= iproc_pcie_reg_paxb_v2
;
1289 pcie
->has_apb_err_disable
= true;
1290 if (pcie
->need_ob_cfg
) {
1291 pcie
->ob_map
= paxb_v2_ob_map
;
1292 pcie
->ob
.nr_windows
= ARRAY_SIZE(paxb_v2_ob_map
);
1294 pcie
->ib
.nr_regions
= ARRAY_SIZE(paxb_v2_ib_map
);
1295 pcie
->ib_map
= paxb_v2_ib_map
;
1296 pcie
->need_msi_steer
= true;
1297 dev_warn(dev
, "reads of config registers that contain %#x return incorrect data\n",
1300 case IPROC_PCIE_PAXC
:
1301 regs
= iproc_pcie_reg_paxc
;
1302 pcie
->ep_is_internal
= true;
1304 case IPROC_PCIE_PAXC_V2
:
1305 regs
= iproc_pcie_reg_paxc_v2
;
1306 pcie
->ep_is_internal
= true;
1307 pcie
->need_msi_steer
= true;
1310 dev_err(dev
, "incompatible iProc PCIe interface\n");
1314 pcie
->reg_offsets
= devm_kcalloc(dev
, IPROC_PCIE_MAX_NUM_REG
,
1315 sizeof(*pcie
->reg_offsets
),
1317 if (!pcie
->reg_offsets
)
1320 /* go through the register table and populate all valid registers */
1321 pcie
->reg_offsets
[0] = (pcie
->type
== IPROC_PCIE_PAXC_V2
) ?
1322 IPROC_PCIE_REG_INVALID
: regs
[0];
1323 for (reg_idx
= 1; reg_idx
< IPROC_PCIE_MAX_NUM_REG
; reg_idx
++)
1324 pcie
->reg_offsets
[reg_idx
] = regs
[reg_idx
] ?
1325 regs
[reg_idx
] : IPROC_PCIE_REG_INVALID
;
1330 int iproc_pcie_setup(struct iproc_pcie
*pcie
, struct list_head
*res
)
1335 struct pci_bus
*child
;
1336 struct pci_host_bridge
*host
= pci_host_bridge_from_priv(pcie
);
1340 ret
= iproc_pcie_rev_init(pcie
);
1342 dev_err(dev
, "unable to initialize controller parameters\n");
1346 ret
= devm_request_pci_bus_resources(dev
, res
);
1350 ret
= phy_init(pcie
->phy
);
1352 dev_err(dev
, "unable to initialize PCIe PHY\n");
1356 ret
= phy_power_on(pcie
->phy
);
1358 dev_err(dev
, "unable to power on PCIe PHY\n");
1362 iproc_pcie_perst_ctrl(pcie
, true);
1363 iproc_pcie_perst_ctrl(pcie
, false);
1365 if (pcie
->need_ob_cfg
) {
1366 ret
= iproc_pcie_map_ranges(pcie
, res
);
1368 dev_err(dev
, "map failed\n");
1369 goto err_power_off_phy
;
1373 if (pcie
->need_ib_cfg
) {
1374 ret
= iproc_pcie_map_dma_ranges(pcie
);
1375 if (ret
&& ret
!= -ENOENT
)
1376 goto err_power_off_phy
;
1380 pcie
->sysdata
.private_data
= pcie
;
1381 sysdata
= &pcie
->sysdata
;
1386 ret
= iproc_pcie_check_link(pcie
);
1388 dev_err(dev
, "no PCIe EP device detected\n");
1389 goto err_power_off_phy
;
1392 iproc_pcie_enable(pcie
);
1394 if (IS_ENABLED(CONFIG_PCI_MSI
))
1395 if (iproc_pcie_msi_enable(pcie
))
1396 dev_info(dev
, "not using iProc MSI\n");
1398 list_splice_init(res
, &host
->windows
);
1400 host
->dev
.parent
= dev
;
1401 host
->ops
= &iproc_pcie_ops
;
1402 host
->sysdata
= sysdata
;
1403 host
->map_irq
= pcie
->map_irq
;
1404 host
->swizzle_irq
= pci_common_swizzle
;
1406 ret
= pci_scan_root_bus_bridge(host
);
1408 dev_err(dev
, "failed to scan host: %d\n", ret
);
1409 goto err_power_off_phy
;
1412 pci_assign_unassigned_bus_resources(host
->bus
);
1414 pcie
->root_bus
= host
->bus
;
1416 list_for_each_entry(child
, &host
->bus
->children
, node
)
1417 pcie_bus_configure_settings(child
);
1419 pci_bus_add_devices(host
->bus
);
1424 phy_power_off(pcie
->phy
);
1426 phy_exit(pcie
->phy
);
1429 EXPORT_SYMBOL(iproc_pcie_setup
);
1431 int iproc_pcie_remove(struct iproc_pcie
*pcie
)
1433 pci_stop_root_bus(pcie
->root_bus
);
1434 pci_remove_root_bus(pcie
->root_bus
);
1436 iproc_pcie_msi_disable(pcie
);
1438 phy_power_off(pcie
->phy
);
1439 phy_exit(pcie
->phy
);
1443 EXPORT_SYMBOL(iproc_pcie_remove
);
1445 MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>");
1446 MODULE_DESCRIPTION("Broadcom iPROC PCIe common driver");
1447 MODULE_LICENSE("GPL v2");