Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
[cris-mirror.git] / drivers / tty / serial / jsm / jsm.h
blob7a128aaa3a667ca2ecc756f25217b3460d4fe38d
1 // SPDX-License-Identifier: GPL-2.0+
2 /************************************************************************
3 * Copyright 2003 Digi International (www.digi.com)
5 * Copyright (C) 2004 IBM Corporation. All rights reserved.
7 * Contact Information:
8 * Scott H Kilau <Scott_Kilau@digi.com>
9 * Wendy Xiong <wendyx@us.ibm.com>
11 ***********************************************************************/
13 #ifndef __JSM_DRIVER_H
14 #define __JSM_DRIVER_H
16 #include <linux/kernel.h>
17 #include <linux/types.h> /* To pick up the varions Linux types */
18 #include <linux/tty.h>
19 #include <linux/serial_core.h>
20 #include <linux/device.h>
23 * Debugging levels can be set using debug insmod variable
24 * They can also be compiled out completely.
26 enum {
27 DBG_INIT = 0x01,
28 DBG_BASIC = 0x02,
29 DBG_CORE = 0x04,
30 DBG_OPEN = 0x08,
31 DBG_CLOSE = 0x10,
32 DBG_READ = 0x20,
33 DBG_WRITE = 0x40,
34 DBG_IOCTL = 0x80,
35 DBG_PROC = 0x100,
36 DBG_PARAM = 0x200,
37 DBG_PSCAN = 0x400,
38 DBG_EVENT = 0x800,
39 DBG_DRAIN = 0x1000,
40 DBG_MSIGS = 0x2000,
41 DBG_MGMT = 0x4000,
42 DBG_INTR = 0x8000,
43 DBG_CARR = 0x10000,
46 #define jsm_dbg(nlevel, pdev, fmt, ...) \
47 do { \
48 if (DBG_##nlevel & jsm_debug) \
49 dev_dbg(pdev->dev, fmt, ##__VA_ARGS__); \
50 } while (0)
52 #define MAXLINES 256
53 #define MAXPORTS 8
54 #define MAX_STOPS_SENT 5
56 /* Board ids */
57 #define PCI_DEVICE_ID_CLASSIC_4 0x0028
58 #define PCI_DEVICE_ID_CLASSIC_8 0x0029
59 #define PCI_DEVICE_ID_CLASSIC_4_422 0x00D0
60 #define PCI_DEVICE_ID_CLASSIC_8_422 0x00D1
61 #define PCI_DEVICE_ID_NEO_4 0x00B0
62 #define PCI_DEVICE_ID_NEO_1_422 0x00CC
63 #define PCI_DEVICE_ID_NEO_1_422_485 0x00CD
64 #define PCI_DEVICE_ID_NEO_2_422_485 0x00CE
65 #define PCIE_DEVICE_ID_NEO_8 0x00F0
66 #define PCIE_DEVICE_ID_NEO_4 0x00F1
67 #define PCIE_DEVICE_ID_NEO_4RJ45 0x00F2
68 #define PCIE_DEVICE_ID_NEO_8RJ45 0x00F3
70 /* Board type definitions */
72 #define T_NEO 0000
73 #define T_CLASSIC 0001
74 #define T_PCIBUS 0400
76 /* Board State Definitions */
78 #define BD_RUNNING 0x0
79 #define BD_REASON 0x7f
80 #define BD_NOTFOUND 0x1
81 #define BD_NOIOPORT 0x2
82 #define BD_NOMEM 0x3
83 #define BD_NOBIOS 0x4
84 #define BD_NOFEP 0x5
85 #define BD_FAILED 0x6
86 #define BD_ALLOCATED 0x7
87 #define BD_TRIBOOT 0x8
88 #define BD_BADKME 0x80
91 /* 4 extra for alignment play space */
92 #define WRITEBUFLEN ((4096) + 4)
94 #define JSM_VERSION "jsm: 1.2-1-INKERNEL"
95 #define JSM_PARTNUM "40002438_A-INKERNEL"
97 struct jsm_board;
98 struct jsm_channel;
100 /************************************************************************
101 * Per board operations structure *
102 ************************************************************************/
103 struct board_ops {
104 irq_handler_t intr;
105 void (*uart_init)(struct jsm_channel *ch);
106 void (*uart_off)(struct jsm_channel *ch);
107 void (*param)(struct jsm_channel *ch);
108 void (*assert_modem_signals)(struct jsm_channel *ch);
109 void (*flush_uart_write)(struct jsm_channel *ch);
110 void (*flush_uart_read)(struct jsm_channel *ch);
111 void (*disable_receiver)(struct jsm_channel *ch);
112 void (*enable_receiver)(struct jsm_channel *ch);
113 void (*send_break)(struct jsm_channel *ch);
114 void (*clear_break)(struct jsm_channel *ch);
115 void (*send_start_character)(struct jsm_channel *ch);
116 void (*send_stop_character)(struct jsm_channel *ch);
117 void (*copy_data_from_queue_to_uart)(struct jsm_channel *ch);
118 u32 (*get_uart_bytes_left)(struct jsm_channel *ch);
119 void (*send_immediate_char)(struct jsm_channel *ch, unsigned char);
124 * Per-board information
126 struct jsm_board
128 int boardnum; /* Board number: 0-32 */
130 int type; /* Type of board */
131 u8 rev; /* PCI revision ID */
132 struct pci_dev *pci_dev;
133 u32 maxports; /* MAX ports this board can handle */
135 spinlock_t bd_intr_lock; /* Used to protect the poller tasklet and
136 * the interrupt routine from each other.
139 u32 nasync; /* Number of ports on card */
141 u32 irq; /* Interrupt request number */
143 u64 membase; /* Start of base memory of the card */
144 u64 membase_end; /* End of base memory of the card */
146 u8 __iomem *re_map_membase;/* Remapped memory of the card */
148 u64 iobase; /* Start of io base of the card */
149 u64 iobase_end; /* End of io base of the card */
151 u32 bd_uart_offset; /* Space between each UART */
153 struct jsm_channel *channels[MAXPORTS]; /* array of pointers to our channels. */
155 u32 bd_dividend; /* Board/UARTs specific dividend */
157 struct board_ops *bd_ops;
159 struct list_head jsm_board_entry;
162 /************************************************************************
163 * Device flag definitions for ch_flags.
164 ************************************************************************/
165 #define CH_PRON 0x0001 /* Printer on string */
166 #define CH_STOP 0x0002 /* Output is stopped */
167 #define CH_STOPI 0x0004 /* Input is stopped */
168 #define CH_CD 0x0008 /* Carrier is present */
169 #define CH_FCAR 0x0010 /* Carrier forced on */
170 #define CH_HANGUP 0x0020 /* Hangup received */
172 #define CH_RECEIVER_OFF 0x0040 /* Receiver is off */
173 #define CH_OPENING 0x0080 /* Port in fragile open state */
174 #define CH_CLOSING 0x0100 /* Port in fragile close state */
175 #define CH_FIFO_ENABLED 0x0200 /* Port has FIFOs enabled */
176 #define CH_TX_FIFO_EMPTY 0x0400 /* TX Fifo is completely empty */
177 #define CH_TX_FIFO_LWM 0x0800 /* TX Fifo is below Low Water */
178 #define CH_BREAK_SENDING 0x1000 /* Break is being sent */
179 #define CH_LOOPBACK 0x2000 /* Channel is in lookback mode */
180 #define CH_BAUD0 0x08000 /* Used for checking B0 transitions */
182 /* Our Read/Error queue sizes */
183 #define RQUEUEMASK 0x1FFF /* 8 K - 1 */
184 #define EQUEUEMASK 0x1FFF /* 8 K - 1 */
185 #define RQUEUESIZE (RQUEUEMASK + 1)
186 #define EQUEUESIZE RQUEUESIZE
189 /************************************************************************
190 * Channel information structure.
191 ************************************************************************/
192 struct jsm_channel {
193 struct uart_port uart_port;
194 struct jsm_board *ch_bd; /* Board structure pointer */
196 spinlock_t ch_lock; /* provide for serialization */
197 wait_queue_head_t ch_flags_wait;
199 u32 ch_portnum; /* Port number, 0 offset. */
200 u32 ch_open_count; /* open count */
201 u32 ch_flags; /* Channel flags */
203 u64 ch_close_delay; /* How long we should drop RTS/DTR for */
205 tcflag_t ch_c_iflag; /* channel iflags */
206 tcflag_t ch_c_cflag; /* channel cflags */
207 tcflag_t ch_c_oflag; /* channel oflags */
208 tcflag_t ch_c_lflag; /* channel lflags */
209 u8 ch_stopc; /* Stop character */
210 u8 ch_startc; /* Start character */
212 u8 ch_mostat; /* FEP output modem status */
213 u8 ch_mistat; /* FEP input modem status */
215 /* Pointers to the "mapped" UART structs */
216 struct neo_uart_struct __iomem *ch_neo_uart; /* NEO card */
217 struct cls_uart_struct __iomem *ch_cls_uart; /* Classic card */
219 u8 ch_cached_lsr; /* Cached value of the LSR register */
221 u8 *ch_rqueue; /* Our read queue buffer - malloc'ed */
222 u16 ch_r_head; /* Head location of the read queue */
223 u16 ch_r_tail; /* Tail location of the read queue */
225 u8 *ch_equeue; /* Our error queue buffer - malloc'ed */
226 u16 ch_e_head; /* Head location of the error queue */
227 u16 ch_e_tail; /* Tail location of the error queue */
229 u64 ch_rxcount; /* total of data received so far */
230 u64 ch_txcount; /* total of data transmitted so far */
232 u8 ch_r_tlevel; /* Receive Trigger level */
233 u8 ch_t_tlevel; /* Transmit Trigger level */
235 u8 ch_r_watermark; /* Receive Watermark */
238 u32 ch_stops_sent; /* How many times I have sent a stop character
239 * to try to stop the other guy sending.
241 u64 ch_err_parity; /* Count of parity errors on channel */
242 u64 ch_err_frame; /* Count of framing errors on channel */
243 u64 ch_err_break; /* Count of breaks on channel */
244 u64 ch_err_overrun; /* Count of overruns on channel */
246 u64 ch_xon_sends; /* Count of xons transmitted */
247 u64 ch_xoff_sends; /* Count of xoffs transmitted */
250 /************************************************************************
251 * Per channel/port Classic UART structures *
252 ************************************************************************
253 * Base Structure Entries Usage Meanings to Host *
255 * W = read write R = read only *
256 * U = Unused. *
257 ************************************************************************/
259 struct cls_uart_struct {
260 u8 txrx; /* WR RHR/THR - Holding Reg */
261 u8 ier; /* WR IER - Interrupt Enable Reg */
262 u8 isr_fcr; /* WR ISR/FCR - Interrupt Status Reg/Fifo Control Reg*/
263 u8 lcr; /* WR LCR - Line Control Reg */
264 u8 mcr; /* WR MCR - Modem Control Reg */
265 u8 lsr; /* WR LSR - Line Status Reg */
266 u8 msr; /* WR MSR - Modem Status Reg */
267 u8 spr; /* WR SPR - Scratch Pad Reg */
270 /* Where to read the interrupt register (8bits) */
271 #define UART_CLASSIC_POLL_ADDR_OFFSET 0x40
273 #define UART_EXAR654_ENHANCED_REGISTER_SET 0xBF
275 #define UART_16654_FCR_TXTRIGGER_8 0x0
276 #define UART_16654_FCR_TXTRIGGER_16 0x10
277 #define UART_16654_FCR_TXTRIGGER_32 0x20
278 #define UART_16654_FCR_TXTRIGGER_56 0x30
280 #define UART_16654_FCR_RXTRIGGER_8 0x0
281 #define UART_16654_FCR_RXTRIGGER_16 0x40
282 #define UART_16654_FCR_RXTRIGGER_56 0x80
283 #define UART_16654_FCR_RXTRIGGER_60 0xC0
285 #define UART_IIR_CTSRTS 0x20 /* Received CTS/RTS change of state */
286 #define UART_IIR_RDI_TIMEOUT 0x0C /* Receiver data TIMEOUT */
289 * These are the EXTENDED definitions for the Exar 654's Interrupt
290 * Enable Register.
292 #define UART_EXAR654_EFR_ECB 0x10 /* Enhanced control bit */
293 #define UART_EXAR654_EFR_IXON 0x2 /* Receiver compares Xon1/Xoff1 */
294 #define UART_EXAR654_EFR_IXOFF 0x8 /* Transmit Xon1/Xoff1 */
295 #define UART_EXAR654_EFR_RTSDTR 0x40 /* Auto RTS/DTR Flow Control Enable */
296 #define UART_EXAR654_EFR_CTSDSR 0x80 /* Auto CTS/DSR Flow COntrol Enable */
298 #define UART_EXAR654_XOFF_DETECT 0x1 /* Indicates whether chip saw an incoming XOFF char */
299 #define UART_EXAR654_XON_DETECT 0x2 /* Indicates whether chip saw an incoming XON char */
301 #define UART_EXAR654_IER_XOFF 0x20 /* Xoff Interrupt Enable */
302 #define UART_EXAR654_IER_RTSDTR 0x40 /* Output Interrupt Enable */
303 #define UART_EXAR654_IER_CTSDSR 0x80 /* Input Interrupt Enable */
305 /************************************************************************
306 * Per channel/port NEO UART structure *
307 ************************************************************************
308 * Base Structure Entries Usage Meanings to Host *
310 * W = read write R = read only *
311 * U = Unused. *
312 ************************************************************************/
314 struct neo_uart_struct {
315 u8 txrx; /* WR RHR/THR - Holding Reg */
316 u8 ier; /* WR IER - Interrupt Enable Reg */
317 u8 isr_fcr; /* WR ISR/FCR - Interrupt Status Reg/Fifo Control Reg */
318 u8 lcr; /* WR LCR - Line Control Reg */
319 u8 mcr; /* WR MCR - Modem Control Reg */
320 u8 lsr; /* WR LSR - Line Status Reg */
321 u8 msr; /* WR MSR - Modem Status Reg */
322 u8 spr; /* WR SPR - Scratch Pad Reg */
323 u8 fctr; /* WR FCTR - Feature Control Reg */
324 u8 efr; /* WR EFR - Enhanced Function Reg */
325 u8 tfifo; /* WR TXCNT/TXTRG - Transmit FIFO Reg */
326 u8 rfifo; /* WR RXCNT/RXTRG - Receive FIFO Reg */
327 u8 xoffchar1; /* WR XOFF 1 - XOff Character 1 Reg */
328 u8 xoffchar2; /* WR XOFF 2 - XOff Character 2 Reg */
329 u8 xonchar1; /* WR XON 1 - Xon Character 1 Reg */
330 u8 xonchar2; /* WR XON 2 - XOn Character 2 Reg */
332 u8 reserved1[0x2ff - 0x200]; /* U Reserved by Exar */
333 u8 txrxburst[64]; /* RW 64 bytes of RX/TX FIFO Data */
334 u8 reserved2[0x37f - 0x340]; /* U Reserved by Exar */
335 u8 rxburst_with_errors[64]; /* R 64 bytes of RX FIFO Data + LSR */
338 /* Where to read the extended interrupt register (32bits instead of 8bits) */
339 #define UART_17158_POLL_ADDR_OFFSET 0x80
342 * These are the redefinitions for the FCTR on the XR17C158, since
343 * Exar made them different than their earlier design. (XR16C854)
346 /* These are only applicable when table D is selected */
347 #define UART_17158_FCTR_RTS_NODELAY 0x00
348 #define UART_17158_FCTR_RTS_4DELAY 0x01
349 #define UART_17158_FCTR_RTS_6DELAY 0x02
350 #define UART_17158_FCTR_RTS_8DELAY 0x03
351 #define UART_17158_FCTR_RTS_12DELAY 0x12
352 #define UART_17158_FCTR_RTS_16DELAY 0x05
353 #define UART_17158_FCTR_RTS_20DELAY 0x13
354 #define UART_17158_FCTR_RTS_24DELAY 0x06
355 #define UART_17158_FCTR_RTS_28DELAY 0x14
356 #define UART_17158_FCTR_RTS_32DELAY 0x07
357 #define UART_17158_FCTR_RTS_36DELAY 0x16
358 #define UART_17158_FCTR_RTS_40DELAY 0x08
359 #define UART_17158_FCTR_RTS_44DELAY 0x09
360 #define UART_17158_FCTR_RTS_48DELAY 0x10
361 #define UART_17158_FCTR_RTS_52DELAY 0x11
363 #define UART_17158_FCTR_RTS_IRDA 0x10
364 #define UART_17158_FCTR_RS485 0x20
365 #define UART_17158_FCTR_TRGA 0x00
366 #define UART_17158_FCTR_TRGB 0x40
367 #define UART_17158_FCTR_TRGC 0x80
368 #define UART_17158_FCTR_TRGD 0xC0
370 /* 17158 trigger table selects.. */
371 #define UART_17158_FCTR_BIT6 0x40
372 #define UART_17158_FCTR_BIT7 0x80
374 /* 17158 TX/RX memmapped buffer offsets */
375 #define UART_17158_RX_FIFOSIZE 64
376 #define UART_17158_TX_FIFOSIZE 64
378 /* 17158 Extended IIR's */
379 #define UART_17158_IIR_RDI_TIMEOUT 0x0C /* Receiver data TIMEOUT */
380 #define UART_17158_IIR_XONXOFF 0x10 /* Received an XON/XOFF char */
381 #define UART_17158_IIR_HWFLOW_STATE_CHANGE 0x20 /* CTS/DSR or RTS/DTR state change */
382 #define UART_17158_IIR_FIFO_ENABLED 0xC0 /* 16550 FIFOs are Enabled */
385 * These are the extended interrupts that get sent
386 * back to us from the UART's 32bit interrupt register
388 #define UART_17158_RX_LINE_STATUS 0x1 /* RX Ready */
389 #define UART_17158_RXRDY_TIMEOUT 0x2 /* RX Ready Timeout */
390 #define UART_17158_TXRDY 0x3 /* TX Ready */
391 #define UART_17158_MSR 0x4 /* Modem State Change */
392 #define UART_17158_TX_AND_FIFO_CLR 0x40 /* Transmitter Holding Reg Empty */
393 #define UART_17158_RX_FIFO_DATA_ERROR 0x80 /* UART detected an RX FIFO Data error */
396 * These are the EXTENDED definitions for the 17C158's Interrupt
397 * Enable Register.
399 #define UART_17158_EFR_ECB 0x10 /* Enhanced control bit */
400 #define UART_17158_EFR_IXON 0x2 /* Receiver compares Xon1/Xoff1 */
401 #define UART_17158_EFR_IXOFF 0x8 /* Transmit Xon1/Xoff1 */
402 #define UART_17158_EFR_RTSDTR 0x40 /* Auto RTS/DTR Flow Control Enable */
403 #define UART_17158_EFR_CTSDSR 0x80 /* Auto CTS/DSR Flow COntrol Enable */
405 #define UART_17158_XOFF_DETECT 0x1 /* Indicates whether chip saw an incoming XOFF char */
406 #define UART_17158_XON_DETECT 0x2 /* Indicates whether chip saw an incoming XON char */
408 #define UART_17158_IER_RSVD1 0x10 /* Reserved by Exar */
409 #define UART_17158_IER_XOFF 0x20 /* Xoff Interrupt Enable */
410 #define UART_17158_IER_RTSDTR 0x40 /* Output Interrupt Enable */
411 #define UART_17158_IER_CTSDSR 0x80 /* Input Interrupt Enable */
413 #define PCI_DEVICE_NEO_2DB9_PCI_NAME "Neo 2 - DB9 Universal PCI"
414 #define PCI_DEVICE_NEO_2DB9PRI_PCI_NAME "Neo 2 - DB9 Universal PCI - Powered Ring Indicator"
415 #define PCI_DEVICE_NEO_2RJ45_PCI_NAME "Neo 2 - RJ45 Universal PCI"
416 #define PCI_DEVICE_NEO_2RJ45PRI_PCI_NAME "Neo 2 - RJ45 Universal PCI - Powered Ring Indicator"
417 #define PCIE_DEVICE_NEO_IBM_PCI_NAME "Neo 4 - PCI Express - IBM"
420 * Our Global Variables.
422 extern struct uart_driver jsm_uart_driver;
423 extern struct board_ops jsm_neo_ops;
424 extern struct board_ops jsm_cls_ops;
425 extern int jsm_debug;
427 /*************************************************************************
429 * Prototypes for non-static functions used in more than one module
431 *************************************************************************/
432 int jsm_tty_init(struct jsm_board *);
433 int jsm_uart_port_init(struct jsm_board *);
434 int jsm_remove_uart_port(struct jsm_board *);
435 void jsm_input(struct jsm_channel *ch);
436 void jsm_check_queue_flow_control(struct jsm_channel *ch);
438 #endif