include/linux/mmc/sdio.h

   1 /*
   2  *  include/linux/mmc/sdio.h
   3  *
   4  *  Copyright 2006-2007 Pierre Ossman
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License as published by
   8  * the Free Software Foundation; either version 2 of the License, or (at
   9  * your option) any later version.
  10  */
  11
  12 #ifndef LINUX_MMC_SDIO_H
  13 #define LINUX_MMC_SDIO_H
  14
  15 /* SDIO commands                         type  argument     response */
  16 #define SD_IO_SEND_OP_COND          5 /* bcr  [23:0] OCR         R4  */
  17 #define SD_IO_RW_DIRECT            52 /* ac   [31:0] See below   R5  */
  18 #define SD_IO_RW_EXTENDED          53 /* adtc [31:0] See below   R5  */
  19
  20 /*
  21  * SD_IO_RW_DIRECT argument format:
  22  *
  23  *      [31] R/W flag
  24  *      [30:28] Function number
  25  *      [27] RAW flag
  26  *      [25:9] Register address
  27  *      [7:0] Data
  28  */
  29
  30 /*
  31  * SD_IO_RW_EXTENDED argument format:
  32  *
  33  *      [31] R/W flag
  34  *      [30:28] Function number
  35  *      [27] Block mode
  36  *      [26] Increment address
  37  *      [25:9] Register address
  38  *      [8:0] Byte/block count
  39  */
  40
  41 #define R4_18V_PRESENT (1<<24)
  42 #define R4_MEMORY_PRESENT (1 << 27)
  43
  44 /*
  45   SDIO status in R5
  46   Type
  47         e : error bit
  48         s : status bit
  49         r : detected and set for the actual command response
  50         x : detected and set during command execution. the host must poll
  51             the card by sending status command in order to read these bits.
  52   Clear condition
  53         a : according to the card state
  54         b : always related to the previous command. Reception of
  55             a valid command will clear it (with a delay of one command)
  56         c : clear by read
  57  */
  58
  59 #define R5_COM_CRC_ERROR        (1 << 15)       /* er, b */
  60 #define R5_ILLEGAL_COMMAND      (1 << 14)       /* er, b */
  61 #define R5_ERROR                (1 << 11)       /* erx, c */
  62 #define R5_FUNCTION_NUMBER      (1 << 9)        /* er, c */
  63 #define R5_OUT_OF_RANGE         (1 << 8)        /* er, c */
  64 #define R5_STATUS(x)            (x & 0xCB00)
  65 #define R5_IO_CURRENT_STATE(x)  ((x & 0x3000) >> 12) /* s, b */
  66
  67 /*
  68  * Card Common Control Registers (CCCR)
  69  */
  70
  71 #define SDIO_CCCR_CCCR          0x00
  72
  73 #define  SDIO_CCCR_REV_1_00     0       /* CCCR/FBR Version 1.00 */
  74 #define  SDIO_CCCR_REV_1_10     1       /* CCCR/FBR Version 1.10 */
  75 #define  SDIO_CCCR_REV_1_20     2       /* CCCR/FBR Version 1.20 */
  76 #define  SDIO_CCCR_REV_3_00     3       /* CCCR/FBR Version 3.00 */
  77
  78 #define  SDIO_SDIO_REV_1_00     0       /* SDIO Spec Version 1.00 */
  79 #define  SDIO_SDIO_REV_1_10     1       /* SDIO Spec Version 1.10 */
  80 #define  SDIO_SDIO_REV_1_20     2       /* SDIO Spec Version 1.20 */
  81 #define  SDIO_SDIO_REV_2_00     3       /* SDIO Spec Version 2.00 */
  82 #define  SDIO_SDIO_REV_3_00     4       /* SDIO Spec Version 3.00 */
  83
  84 #define SDIO_CCCR_SD            0x01
  85
  86 #define  SDIO_SD_REV_1_01       0       /* SD Physical Spec Version 1.01 */
  87 #define  SDIO_SD_REV_1_10       1       /* SD Physical Spec Version 1.10 */
  88 #define  SDIO_SD_REV_2_00       2       /* SD Physical Spec Version 2.00 */
  89 #define  SDIO_SD_REV_3_00       3       /* SD Physical Spev Version 3.00 */
  90
  91 #define SDIO_CCCR_IOEx          0x02
  92 #define SDIO_CCCR_IORx          0x03
  93
  94 #define SDIO_CCCR_IENx          0x04    /* Function/Master Interrupt Enable */
  95 #define SDIO_CCCR_INTx          0x05    /* Function Interrupt Pending */
  96
  97 #define SDIO_CCCR_ABORT         0x06    /* function abort/card reset */
  98
  99 #define SDIO_CCCR_IF            0x07    /* bus interface controls */
 100
 101 #define  SDIO_BUS_WIDTH_MASK    0x03    /* data bus width setting */
 102 #define  SDIO_BUS_WIDTH_1BIT    0x00
 103 #define  SDIO_BUS_WIDTH_RESERVED 0x01
 104 #define  SDIO_BUS_WIDTH_4BIT    0x02
 105 #define  SDIO_BUS_ECSI          0x20    /* Enable continuous SPI interrupt */
 106 #define  SDIO_BUS_SCSI          0x40    /* Support continuous SPI interrupt */
 107
 108 #define  SDIO_BUS_ASYNC_INT     0x20
 109
 110 #define  SDIO_BUS_CD_DISABLE     0x80   /* disable pull-up on DAT3 (pin 1) */
 111
 112 #define SDIO_CCCR_CAPS          0x08
 113
 114 #define  SDIO_CCCR_CAP_SDC      0x01    /* can do CMD52 while data transfer */
 115 #define  SDIO_CCCR_CAP_SMB      0x02    /* can do multi-block xfers (CMD53) */
 116 #define  SDIO_CCCR_CAP_SRW      0x04    /* supports read-wait protocol */
 117 #define  SDIO_CCCR_CAP_SBS      0x08    /* supports suspend/resume */
 118 #define  SDIO_CCCR_CAP_S4MI     0x10    /* interrupt during 4-bit CMD53 */
 119 #define  SDIO_CCCR_CAP_E4MI     0x20    /* enable ints during 4-bit CMD53 */
 120 #define  SDIO_CCCR_CAP_LSC      0x40    /* low speed card */
 121 #define  SDIO_CCCR_CAP_4BLS     0x80    /* 4 bit low speed card */
 122
 123 #define SDIO_CCCR_CIS           0x09    /* common CIS pointer (3 bytes) */
 124
 125 /* Following 4 regs are valid only if SBS is set */
 126 #define SDIO_CCCR_SUSPEND       0x0c
 127 #define SDIO_CCCR_SELx          0x0d
 128 #define SDIO_CCCR_EXECx         0x0e
 129 #define SDIO_CCCR_READYx        0x0f
 130
 131 #define SDIO_CCCR_BLKSIZE       0x10
 132
 133 #define SDIO_CCCR_POWER         0x12
 134
 135 #define  SDIO_POWER_SMPC        0x01    /* Supports Master Power Control */
 136 #define  SDIO_POWER_EMPC        0x02    /* Enable Master Power Control */
 137
 138 #define SDIO_CCCR_SPEED         0x13
 139
 140 #define  SDIO_SPEED_SHS         0x01    /* Supports High-Speed mode */
 141 #define  SDIO_SPEED_BSS_SHIFT   1
 142 #define  SDIO_SPEED_BSS_MASK    (7<<SDIO_SPEED_BSS_SHIFT)
 143 #define  SDIO_SPEED_SDR12       (0<<SDIO_SPEED_BSS_SHIFT)
 144 #define  SDIO_SPEED_SDR25       (1<<SDIO_SPEED_BSS_SHIFT)
 145 #define  SDIO_SPEED_SDR50       (2<<SDIO_SPEED_BSS_SHIFT)
 146 #define  SDIO_SPEED_SDR104      (3<<SDIO_SPEED_BSS_SHIFT)
 147 #define  SDIO_SPEED_DDR50       (4<<SDIO_SPEED_BSS_SHIFT)
 148 #define  SDIO_SPEED_EHS         SDIO_SPEED_SDR25        /* Enable High-Speed */
 149
 150 #define SDIO_CCCR_UHS           0x14
 151 #define  SDIO_UHS_SDR50         0x01
 152 #define  SDIO_UHS_SDR104        0x02
 153 #define  SDIO_UHS_DDR50         0x04
 154
 155 #define SDIO_CCCR_DRIVE_STRENGTH 0x15
 156 #define  SDIO_SDTx_MASK         0x07
 157 #define  SDIO_DRIVE_SDTA        (1<<0)
 158 #define  SDIO_DRIVE_SDTC        (1<<1)
 159 #define  SDIO_DRIVE_SDTD        (1<<2)
 160 #define  SDIO_DRIVE_DTSx_MASK   0x03
 161 #define  SDIO_DRIVE_DTSx_SHIFT  4
 162 #define  SDIO_DTSx_SET_TYPE_B   (0 << SDIO_DRIVE_DTSx_SHIFT)
 163 #define  SDIO_DTSx_SET_TYPE_A   (1 << SDIO_DRIVE_DTSx_SHIFT)
 164 #define  SDIO_DTSx_SET_TYPE_C   (2 << SDIO_DRIVE_DTSx_SHIFT)
 165 #define  SDIO_DTSx_SET_TYPE_D   (3 << SDIO_DRIVE_DTSx_SHIFT)
 166 /*
 167  * Function Basic Registers (FBR)
 168  */
 169
 170 #define SDIO_FBR_BASE(f)        ((f) * 0x100) /* base of function f's FBRs */
 171
 172 #define SDIO_FBR_STD_IF         0x00
 173
 174 #define  SDIO_FBR_SUPPORTS_CSA  0x40    /* supports Code Storage Area */
 175 #define  SDIO_FBR_ENABLE_CSA    0x80    /* enable Code Storage Area */
 176
 177 #define SDIO_FBR_STD_IF_EXT     0x01
 178
 179 #define SDIO_FBR_POWER          0x02
 180
 181 #define  SDIO_FBR_POWER_SPS     0x01    /* Supports Power Selection */
 182 #define  SDIO_FBR_POWER_EPS     0x02    /* Enable (low) Power Selection */
 183
 184 #define SDIO_FBR_CIS            0x09    /* CIS pointer (3 bytes) */
 185
 186
 187 #define SDIO_FBR_CSA            0x0C    /* CSA pointer (3 bytes) */
 188
 189 #define SDIO_FBR_CSA_DATA       0x0F
 190
 191 #define SDIO_FBR_BLKSIZE        0x10    /* block size (2 bytes) */
 192
 193 #endif /* LINUX_MMC_SDIO_H */