drivers/usb/gadget/net2280.h

   1 /*
   2  * NetChip 2280 high/full speed USB device controller.
   3  * Unlike many such controllers, this one talks PCI.
   4  */
   5
   6 /*
   7  * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)
   8  * Copyright (C) 2003 David Brownell
   9  *
  10  * This program is free software; you can redistribute it and/or modify
  11  * it under the terms of the GNU General Public License as published by
  12  * the Free Software Foundation; either version 2 of the License, or
  13  * (at your option) any later version.
  14  *
  15  * This program is distributed in the hope that it will be useful,
  16  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  17  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  18  * GNU General Public License for more details.
  19  *
  20  * You should have received a copy of the GNU General Public License
  21  * along with this program; if not, write to the Free Software
  22  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  23  */
  24
  25 /*-------------------------------------------------------------------------*/
  26
  27 /* NET2280 MEMORY MAPPED REGISTERS
  28  *
  29  * The register layout came from the chip documentation, and the bit
  30  * number definitions were extracted from chip specification.
  31  *
  32  * Use the shift operator ('<<') to build bit masks, with readl/writel
  33  * to access the registers through PCI.
  34  */
  35
  36 /* main registers, BAR0 + 0x0000 */
  37 struct net2280_regs {
  38         // offset 0x0000
  39         u32             devinit;
  40 #define     LOCAL_CLOCK_FREQUENCY                               8
  41 #define     FORCE_PCI_RESET                                     7
  42 #define     PCI_ID                                              6
  43 #define     PCI_ENABLE                                          5
  44 #define     FIFO_SOFT_RESET                                     4
  45 #define     CFG_SOFT_RESET                                      3
  46 #define     PCI_SOFT_RESET                                      2
  47 #define     USB_SOFT_RESET                                      1
  48 #define     M8051_RESET                                         0
  49         u32             eectl;
  50 #define     EEPROM_ADDRESS_WIDTH                                23
  51 #define     EEPROM_CHIP_SELECT_ACTIVE                           22
  52 #define     EEPROM_PRESENT                                      21
  53 #define     EEPROM_VALID                                        20
  54 #define     EEPROM_BUSY                                         19
  55 #define     EEPROM_CHIP_SELECT_ENABLE                           18
  56 #define     EEPROM_BYTE_READ_START                              17
  57 #define     EEPROM_BYTE_WRITE_START                             16
  58 #define     EEPROM_READ_DATA                                    8
  59 #define     EEPROM_WRITE_DATA                                   0
  60         u32             eeclkfreq;
  61         u32             _unused0;
  62         // offset 0x0010
  63
  64         u32             pciirqenb0;             /* interrupt PCI master ... */
  65 #define     SETUP_PACKET_INTERRUPT_ENABLE                       7
  66 #define     ENDPOINT_F_INTERRUPT_ENABLE                         6
  67 #define     ENDPOINT_E_INTERRUPT_ENABLE                         5
  68 #define     ENDPOINT_D_INTERRUPT_ENABLE                         4
  69 #define     ENDPOINT_C_INTERRUPT_ENABLE                         3
  70 #define     ENDPOINT_B_INTERRUPT_ENABLE                         2
  71 #define     ENDPOINT_A_INTERRUPT_ENABLE                         1
  72 #define     ENDPOINT_0_INTERRUPT_ENABLE                         0
  73         u32             pciirqenb1;
  74 #define     PCI_INTERRUPT_ENABLE                                31
  75 #define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
  76 #define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
  77 #define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
  78 #define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
  79 #define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
  80 #define     PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE          18
  81 #define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
  82 #define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
  83 #define     GPIO_INTERRUPT_ENABLE                               13
  84 #define     DMA_D_INTERRUPT_ENABLE                              12
  85 #define     DMA_C_INTERRUPT_ENABLE                              11
  86 #define     DMA_B_INTERRUPT_ENABLE                              10
  87 #define     DMA_A_INTERRUPT_ENABLE                              9
  88 #define     EEPROM_DONE_INTERRUPT_ENABLE                        8
  89 #define     VBUS_INTERRUPT_ENABLE                               7
  90 #define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
  91 #define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
  92 #define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
  93 #define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
  94 #define     RESUME_INTERRUPT_ENABLE                             1
  95 #define     SOF_INTERRUPT_ENABLE                                0
  96         u32             cpu_irqenb0;            /* ... or onboard 8051 */
  97 #define     SETUP_PACKET_INTERRUPT_ENABLE                       7
  98 #define     ENDPOINT_F_INTERRUPT_ENABLE                         6
  99 #define     ENDPOINT_E_INTERRUPT_ENABLE                         5
 100 #define     ENDPOINT_D_INTERRUPT_ENABLE                         4
 101 #define     ENDPOINT_C_INTERRUPT_ENABLE                         3
 102 #define     ENDPOINT_B_INTERRUPT_ENABLE                         2
 103 #define     ENDPOINT_A_INTERRUPT_ENABLE                         1
 104 #define     ENDPOINT_0_INTERRUPT_ENABLE                         0
 105         u32             cpu_irqenb1;
 106 #define     CPU_INTERRUPT_ENABLE                                31
 107 #define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
 108 #define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
 109 #define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
 110 #define     PCI_INTA_INTERRUPT_ENABLE                           24
 111 #define     PCI_PME_INTERRUPT_ENABLE                            23
 112 #define     PCI_SERR_INTERRUPT_ENABLE                           22
 113 #define     PCI_PERR_INTERRUPT_ENABLE                           21
 114 #define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
 115 #define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
 116 #define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
 117 #define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
 118 #define     GPIO_INTERRUPT_ENABLE                               13
 119 #define     DMA_D_INTERRUPT_ENABLE                              12
 120 #define     DMA_C_INTERRUPT_ENABLE                              11
 121 #define     DMA_B_INTERRUPT_ENABLE                              10
 122 #define     DMA_A_INTERRUPT_ENABLE                              9
 123 #define     EEPROM_DONE_INTERRUPT_ENABLE                        8
 124 #define     VBUS_INTERRUPT_ENABLE                               7
 125 #define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
 126 #define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
 127 #define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
 128 #define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
 129 #define     RESUME_INTERRUPT_ENABLE                             1
 130 #define     SOF_INTERRUPT_ENABLE                                0
 131
 132         // offset 0x0020
 133         u32             _unused1;
 134         u32             usbirqenb1;
 135 #define     USB_INTERRUPT_ENABLE                                31
 136 #define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
 137 #define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
 138 #define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
 139 #define     PCI_INTA_INTERRUPT_ENABLE                           24
 140 #define     PCI_PME_INTERRUPT_ENABLE                            23
 141 #define     PCI_SERR_INTERRUPT_ENABLE                           22
 142 #define     PCI_PERR_INTERRUPT_ENABLE                           21
 143 #define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
 144 #define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
 145 #define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
 146 #define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
 147 #define     GPIO_INTERRUPT_ENABLE                               13
 148 #define     DMA_D_INTERRUPT_ENABLE                              12
 149 #define     DMA_C_INTERRUPT_ENABLE                              11
 150 #define     DMA_B_INTERRUPT_ENABLE                              10
 151 #define     DMA_A_INTERRUPT_ENABLE                              9
 152 #define     EEPROM_DONE_INTERRUPT_ENABLE                        8
 153 #define     VBUS_INTERRUPT_ENABLE                               7
 154 #define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
 155 #define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
 156 #define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
 157 #define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
 158 #define     RESUME_INTERRUPT_ENABLE                             1
 159 #define     SOF_INTERRUPT_ENABLE                                0
 160         u32             irqstat0;
 161 #define     INTA_ASSERTED                                       12
 162 #define     SETUP_PACKET_INTERRUPT                              7
 163 #define     ENDPOINT_F_INTERRUPT                                6
 164 #define     ENDPOINT_E_INTERRUPT                                5
 165 #define     ENDPOINT_D_INTERRUPT                                4
 166 #define     ENDPOINT_C_INTERRUPT                                3
 167 #define     ENDPOINT_B_INTERRUPT                                2
 168 #define     ENDPOINT_A_INTERRUPT                                1
 169 #define     ENDPOINT_0_INTERRUPT                                0
 170         u32             irqstat1;
 171 #define     POWER_STATE_CHANGE_INTERRUPT                        27
 172 #define     PCI_ARBITER_TIMEOUT_INTERRUPT                       26
 173 #define     PCI_PARITY_ERROR_INTERRUPT                          25
 174 #define     PCI_INTA_INTERRUPT                                  24
 175 #define     PCI_PME_INTERRUPT                                   23
 176 #define     PCI_SERR_INTERRUPT                                  22
 177 #define     PCI_PERR_INTERRUPT                                  21
 178 #define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT                 20
 179 #define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT                 19
 180 #define     PCI_RETRY_ABORT_INTERRUPT                           17
 181 #define     PCI_MASTER_CYCLE_DONE_INTERRUPT                     16
 182 #define     GPIO_INTERRUPT                                      13
 183 #define     DMA_D_INTERRUPT                                     12
 184 #define     DMA_C_INTERRUPT                                     11
 185 #define     DMA_B_INTERRUPT                                     10
 186 #define     DMA_A_INTERRUPT                                     9
 187 #define     EEPROM_DONE_INTERRUPT                               8
 188 #define     VBUS_INTERRUPT                                      7
 189 #define     CONTROL_STATUS_INTERRUPT                            6
 190 #define     ROOT_PORT_RESET_INTERRUPT                           4
 191 #define     SUSPEND_REQUEST_INTERRUPT                           3
 192 #define     SUSPEND_REQUEST_CHANGE_INTERRUPT                    2
 193 #define     RESUME_INTERRUPT                                    1
 194 #define     SOF_INTERRUPT                                       0
 195         // offset 0x0030
 196         u32             idxaddr;
 197         u32             idxdata;
 198         u32             fifoctl;
 199 #define     PCI_BASE2_RANGE                                     16
 200 #define     IGNORE_FIFO_AVAILABILITY                            3
 201 #define     PCI_BASE2_SELECT                                    2
 202 #define     FIFO_CONFIGURATION_SELECT                           0
 203         u32             _unused2;
 204         // offset 0x0040
 205         u32             memaddr;
 206 #define     START                                               28
 207 #define     DIRECTION                                           27
 208 #define     FIFO_DIAGNOSTIC_SELECT                              24
 209 #define     MEMORY_ADDRESS                                      0
 210         u32             memdata0;
 211         u32             memdata1;
 212         u32             _unused3;
 213         // offset 0x0050
 214         u32             gpioctl;
 215 #define     GPIO3_LED_SELECT                                    12
 216 #define     GPIO3_INTERRUPT_ENABLE                              11
 217 #define     GPIO2_INTERRUPT_ENABLE                              10
 218 #define     GPIO1_INTERRUPT_ENABLE                              9
 219 #define     GPIO0_INTERRUPT_ENABLE                              8
 220 #define     GPIO3_OUTPUT_ENABLE                                 7
 221 #define     GPIO2_OUTPUT_ENABLE                                 6
 222 #define     GPIO1_OUTPUT_ENABLE                                 5
 223 #define     GPIO0_OUTPUT_ENABLE                                 4
 224 #define     GPIO3_DATA                                          3
 225 #define     GPIO2_DATA                                          2
 226 #define     GPIO1_DATA                                          1
 227 #define     GPIO0_DATA                                          0
 228         u32             gpiostat;
 229 #define     GPIO3_INTERRUPT                                     3
 230 #define     GPIO2_INTERRUPT                                     2
 231 #define     GPIO1_INTERRUPT                                     1
 232 #define     GPIO0_INTERRUPT                                     0
 233 } __attribute__ ((packed));
 234
 235 /* usb control, BAR0 + 0x0080 */
 236 struct net2280_usb_regs {
 237         // offset 0x0080
 238         u32             stdrsp;
 239 #define     STALL_UNSUPPORTED_REQUESTS                          31
 240 #define     SET_TEST_MODE                                       16
 241 #define     GET_OTHER_SPEED_CONFIGURATION                       15
 242 #define     GET_DEVICE_QUALIFIER                                14
 243 #define     SET_ADDRESS                                         13
 244 #define     ENDPOINT_SET_CLEAR_HALT                             12
 245 #define     DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP               11
 246 #define     GET_STRING_DESCRIPTOR_2                             10
 247 #define     GET_STRING_DESCRIPTOR_1                             9
 248 #define     GET_STRING_DESCRIPTOR_0                             8
 249 #define     GET_SET_INTERFACE                                   6
 250 #define     GET_SET_CONFIGURATION                               5
 251 #define     GET_CONFIGURATION_DESCRIPTOR                        4
 252 #define     GET_DEVICE_DESCRIPTOR                               3
 253 #define     GET_ENDPOINT_STATUS                                 2
 254 #define     GET_INTERFACE_STATUS                                1
 255 #define     GET_DEVICE_STATUS                                   0
 256         u32             prodvendid;
 257 #define     PRODUCT_ID                                          16
 258 #define     VENDOR_ID                                           0
 259         u32             relnum;
 260         u32             usbctl;
 261 #define     SERIAL_NUMBER_INDEX                                 16
 262 #define     PRODUCT_ID_STRING_ENABLE                            13
 263 #define     VENDOR_ID_STRING_ENABLE                             12
 264 #define     USB_ROOT_PORT_WAKEUP_ENABLE                         11
 265 #define     VBUS_PIN                                            10
 266 #define     TIMED_DISCONNECT                                    9
 267 #define     SUSPEND_IMMEDIATELY                                 7
 268 #define     SELF_POWERED_USB_DEVICE                             6
 269 #define     REMOTE_WAKEUP_SUPPORT                               5
 270 #define     PME_POLARITY                                        4
 271 #define     USB_DETECT_ENABLE                                   3
 272 #define     PME_WAKEUP_ENABLE                                   2
 273 #define     DEVICE_REMOTE_WAKEUP_ENABLE                         1
 274 #define     SELF_POWERED_STATUS                                 0
 275         // offset 0x0090
 276         u32             usbstat;
 277 #define     HIGH_SPEED                                          7
 278 #define     FULL_SPEED                                          6
 279 #define     GENERATE_RESUME                                     5
 280 #define     GENERATE_DEVICE_REMOTE_WAKEUP                       4
 281         u32             xcvrdiag;
 282 #define     FORCE_HIGH_SPEED_MODE                               31
 283 #define     FORCE_FULL_SPEED_MODE                               30
 284 #define     USB_TEST_MODE                                       24
 285 #define     LINE_STATE                                          16
 286 #define     TRANSCEIVER_OPERATION_MODE                          2
 287 #define     TRANSCEIVER_SELECT                                  1
 288 #define     TERMINATION_SELECT                                  0
 289         u32             setup0123;
 290         u32             setup4567;
 291         // offset 0x0090
 292         u32             _unused0;
 293         u32             ouraddr;
 294 #define     FORCE_IMMEDIATE                                     7
 295 #define     OUR_USB_ADDRESS                                     0
 296         u32             ourconfig;
 297 } __attribute__ ((packed));
 298
 299 /* pci control, BAR0 + 0x0100 */
 300 struct net2280_pci_regs {
 301         // offset 0x0100
 302         u32              pcimstctl;
 303 #define     PCI_ARBITER_PARK_SELECT                             13
 304 #define     PCI_MULTI LEVEL_ARBITER                             12
 305 #define     PCI_RETRY_ABORT_ENABLE                              11
 306 #define     DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE              10
 307 #define     DMA_READ_MULTIPLE_ENABLE                            9
 308 #define     DMA_READ_LINE_ENABLE                                8
 309 #define     PCI_MASTER_COMMAND_SELECT                           6
 310 #define         MEM_READ_OR_WRITE                                   0
 311 #define         IO_READ_OR_WRITE                                    1
 312 #define         CFG_READ_OR_WRITE                                   2
 313 #define     PCI_MASTER_START                                    5
 314 #define     PCI_MASTER_READ_WRITE                               4
 315 #define         PCI_MASTER_WRITE                                    0
 316 #define         PCI_MASTER_READ                                     1
 317 #define     PCI_MASTER_BYTE_WRITE_ENABLES                       0
 318         u32              pcimstaddr;
 319         u32              pcimstdata;
 320         u32              pcimststat;
 321 #define     PCI_ARBITER_CLEAR                                   2
 322 #define     PCI_EXTERNAL_ARBITER                                1
 323 #define     PCI_HOST_MODE                                       0
 324 } __attribute__ ((packed));
 325
 326 /* dma control, BAR0 + 0x0180 ... array of four structs like this,
 327  * for channels 0..3.  see also struct net2280_dma:  descriptor
 328  * that can be loaded into some of these registers.
 329  */
 330 struct net2280_dma_regs {       /* [11.7] */
 331         // offset 0x0180, 0x01a0, 0x01c0, 0x01e0,
 332         u32             dmactl;
 333 #define     DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE            25
 334 #define     DMA_CLEAR_COUNT_ENABLE                              21
 335 #define     DESCRIPTOR_POLLING_RATE                             19
 336 #define         POLL_CONTINUOUS                                     0
 337 #define         POLL_1_USEC                                         1
 338 #define         POLL_100_USEC                                       2
 339 #define         POLL_1_MSEC                                         3
 340 #define     DMA_VALID_BIT_POLLING_ENABLE                        18
 341 #define     DMA_VALID_BIT_ENABLE                                17
 342 #define     DMA_SCATTER_GATHER_ENABLE                           16
 343 #define     DMA_OUT_AUTO_START_ENABLE                           4
 344 #define     DMA_PREEMPT_ENABLE                                  3
 345 #define     DMA_FIFO_VALIDATE                                   2
 346 #define     DMA_ENABLE                                          1
 347 #define     DMA_ADDRESS_HOLD                                    0
 348         u32             dmastat;
 349 #define     DMA_SCATTER_GATHER_DONE_INTERRUPT                   25
 350 #define     DMA_TRANSACTION_DONE_INTERRUPT                      24
 351 #define     DMA_ABORT                                           1
 352 #define     DMA_START                                           0
 353         u32             _unused0 [2];
 354         // offset 0x0190, 0x01b0, 0x01d0, 0x01f0,
 355         u32             dmacount;
 356 #define     VALID_BIT                                           31
 357 #define     DMA_DIRECTION                                       30
 358 #define     DMA_DONE_INTERRUPT_ENABLE                           29
 359 #define     END_OF_CHAIN                                        28
 360 #define         DMA_BYTE_COUNT_MASK                                 ((1<<24)-1)
 361 #define     DMA_BYTE_COUNT                                      0
 362         u32             dmaaddr;
 363         u32             dmadesc;
 364         u32             _unused1;
 365 } __attribute__ ((packed));
 366
 367 /* dedicated endpoint registers, BAR0 + 0x0200 */
 368
 369 struct net2280_dep_regs {       /* [11.8] */
 370         // offset 0x0200, 0x0210, 0x220, 0x230, 0x240
 371         u32             dep_cfg;
 372         // offset 0x0204, 0x0214, 0x224, 0x234, 0x244
 373         u32             dep_rsp;
 374         u32             _unused [2];
 375 } __attribute__ ((packed));
 376
 377 /* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
 378  * like this, for ep0 then the configurable endpoints A..F
 379  * ep0 reserved for control; E and F have only 64 bytes of fifo
 380  */
 381 struct net2280_ep_regs {        /* [11.9] */
 382         // offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0
 383         u32             ep_cfg;
 384 #define     ENDPOINT_BYTE_COUNT                                 16
 385 #define     ENDPOINT_ENABLE                                     10
 386 #define     ENDPOINT_TYPE                                       8
 387 #define     ENDPOINT_DIRECTION                                  7
 388 #define     ENDPOINT_NUMBER                                     0
 389         u32             ep_rsp;
 390 #define     SET_NAK_OUT_PACKETS                                 15
 391 #define     SET_EP_HIDE_STATUS_PHASE                            14
 392 #define     SET_EP_FORCE_CRC_ERROR                              13
 393 #define     SET_INTERRUPT_MODE                                  12
 394 #define     SET_CONTROL_STATUS_PHASE_HANDSHAKE                  11
 395 #define     SET_NAK_OUT_PACKETS_MODE                            10
 396 #define     SET_ENDPOINT_TOGGLE                                 9
 397 #define     SET_ENDPOINT_HALT                                   8
 398 #define     CLEAR_NAK_OUT_PACKETS                               7
 399 #define     CLEAR_EP_HIDE_STATUS_PHASE                          6
 400 #define     CLEAR_EP_FORCE_CRC_ERROR                            5
 401 #define     CLEAR_INTERRUPT_MODE                                4
 402 #define     CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE                3
 403 #define     CLEAR_NAK_OUT_PACKETS_MODE                          2
 404 #define     CLEAR_ENDPOINT_TOGGLE                               1
 405 #define     CLEAR_ENDPOINT_HALT                                 0
 406         u32             ep_irqenb;
 407 #define     SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE              6
 408 #define     SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE           5
 409 #define     DATA_PACKET_RECEIVED_INTERRUPT_ENABLE               3
 410 #define     DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE            2
 411 #define     DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE                1
 412 #define     DATA_IN_TOKEN_INTERRUPT_ENABLE                      0
 413         u32             ep_stat;
 414 #define     FIFO_VALID_COUNT                                    24
 415 #define     HIGH_BANDWIDTH_OUT_TRANSACTION_PID                  22
 416 #define     TIMEOUT                                             21
 417 #define     USB_STALL_SENT                                      20
 418 #define     USB_IN_NAK_SENT                                     19
 419 #define     USB_IN_ACK_RCVD                                     18
 420 #define     USB_OUT_PING_NAK_SENT                               17
 421 #define     USB_OUT_ACK_SENT                                    16
 422 #define     FIFO_OVERFLOW                                       13
 423 #define     FIFO_UNDERFLOW                                      12
 424 #define     FIFO_FULL                                           11
 425 #define     FIFO_EMPTY                                          10
 426 #define     FIFO_FLUSH                                          9
 427 #define     SHORT_PACKET_OUT_DONE_INTERRUPT                     6
 428 #define     SHORT_PACKET_TRANSFERRED_INTERRUPT                  5
 429 #define     NAK_OUT_PACKETS                                     4
 430 #define     DATA_PACKET_RECEIVED_INTERRUPT                      3
 431 #define     DATA_PACKET_TRANSMITTED_INTERRUPT                   2
 432 #define     DATA_OUT_PING_TOKEN_INTERRUPT                       1
 433 #define     DATA_IN_TOKEN_INTERRUPT                             0
 434         // offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0
 435         u32             ep_avail;
 436         u32             ep_data;
 437         u32             _unused0 [2];
 438 } __attribute__ ((packed));
 439
 440 /*-------------------------------------------------------------------------*/
 441
 442 #ifdef  __KERNEL__
 443
 444 /* indexed registers [11.10] are accessed indirectly
 445  * caller must own the device lock.
 446  */
 447
 448 static inline u32
 449 get_idx_reg (struct net2280_regs __iomem *regs, u32 index)
 450 {
 451         writel (index, &regs->idxaddr);
 452         /* NOTE:  synchs device/cpu memory views */
 453         return readl (&regs->idxdata);
 454 }
 455
 456 static inline void
 457 set_idx_reg (struct net2280_regs __iomem *regs, u32 index, u32 value)
 458 {
 459         writel (index, &regs->idxaddr);
 460         writel (value, &regs->idxdata);
 461         /* posted, may not be visible yet */
 462 }
 463
 464 #endif  /* __KERNEL__ */
 465
 466
 467 #define REG_DIAG                0x0
 468 #define     RETRY_COUNTER                                       16
 469 #define     FORCE_PCI_SERR                                      11
 470 #define     FORCE_PCI_INTERRUPT                                 10
 471 #define     FORCE_USB_INTERRUPT                                 9
 472 #define     FORCE_CPU_INTERRUPT                                 8
 473 #define     ILLEGAL_BYTE_ENABLES                                5
 474 #define     FAST_TIMES                                          4
 475 #define     FORCE_RECEIVE_ERROR                                 2
 476 #define     FORCE_TRANSMIT_CRC_ERROR                            0
 477 #define REG_FRAME               0x02    /* from last sof */
 478 #define REG_CHIPREV             0x03    /* in bcd */
 479 #define REG_HS_NAK_RATE         0x0a    /* NAK per N uframes */
 480
 481 #define CHIPREV_1       0x0100
 482 #define CHIPREV_1A      0x0110
 483
 484 #ifdef  __KERNEL__
 485
 486 /* ep a-f highspeed and fullspeed maxpacket, addresses
 487  * computed from ep->num
 488  */
 489 #define REG_EP_MAXPKT(dev,num) (((num) + 1) * 0x10 + \
 490                 (((dev)->gadget.speed == USB_SPEED_HIGH) ? 0 : 1))
 491
 492 /*-------------------------------------------------------------------------*/
 493
 494 /* [8.3] for scatter/gather i/o
 495  * use struct net2280_dma_regs bitfields
 496  */
 497 struct net2280_dma {
 498         __le32          dmacount;
 499         __le32          dmaaddr;                /* the buffer */
 500         __le32          dmadesc;                /* next dma descriptor */
 501         __le32          _reserved;
 502 } __attribute__ ((aligned (16)));
 503
 504 /*-------------------------------------------------------------------------*/
 505
 506 /* DRIVER DATA STRUCTURES and UTILITIES */
 507
 508 struct net2280_ep {
 509         struct usb_ep                           ep;
 510         struct net2280_ep_regs                  __iomem *regs;
 511         struct net2280_dma_regs                 __iomem *dma;
 512         struct net2280_dma                      *dummy;
 513         dma_addr_t                              td_dma; /* of dummy */
 514         struct net2280                          *dev;
 515         unsigned long                           irqs;
 516
 517         /* analogous to a host-side qh */
 518         struct list_head                        queue;
 519         const struct usb_endpoint_descriptor    *desc;
 520         unsigned                                num : 8,
 521                                                 fifo_size : 12,
 522                                                 in_fifo_validate : 1,
 523                                                 out_overflow : 1,
 524                                                 stopped : 1,
 525                                                 is_in : 1,
 526                                                 is_iso : 1;
 527 };
 528
 529 static inline void allow_status (struct net2280_ep *ep)
 530 {
 531         /* ep0 only */
 532         writel (  (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
 533                 | (1 << CLEAR_NAK_OUT_PACKETS)
 534                 | (1 << CLEAR_NAK_OUT_PACKETS_MODE)
 535                 , &ep->regs->ep_rsp);
 536         ep->stopped = 1;
 537 }
 538
 539 /* count (<= 4) bytes in the next fifo write will be valid */
 540 static inline void set_fifo_bytecount (struct net2280_ep *ep, unsigned count)
 541 {
 542         writeb (count, 2 + (u8 __iomem *) &ep->regs->ep_cfg);
 543 }
 544
 545 struct net2280_request {
 546         struct usb_request              req;
 547         struct net2280_dma              *td;
 548         dma_addr_t                      td_dma;
 549         struct list_head                queue;
 550         unsigned                        mapped : 1,
 551                                         valid : 1;
 552 };
 553
 554 struct net2280 {
 555         /* each pci device provides one gadget, several endpoints */
 556         struct usb_gadget               gadget;
 557         spinlock_t                      lock;
 558         struct net2280_ep               ep [7];
 559         struct usb_gadget_driver        *driver;
 560         unsigned                        enabled : 1,
 561                                         protocol_stall : 1,
 562                                         softconnect : 1,
 563                                         got_irq : 1,
 564                                         region : 1;
 565         u16                             chiprev;
 566
 567         /* pci state used to access those endpoints */
 568         struct pci_dev                  *pdev;
 569         struct net2280_regs             __iomem *regs;
 570         struct net2280_usb_regs         __iomem *usb;
 571         struct net2280_pci_regs         __iomem *pci;
 572         struct net2280_dma_regs         __iomem *dma;
 573         struct net2280_dep_regs         __iomem *dep;
 574         struct net2280_ep_regs          __iomem *epregs;
 575
 576         struct pci_pool                 *requests;
 577         // statistics...
 578 };
 579
 580 static inline void set_halt (struct net2280_ep *ep)
 581 {
 582         /* ep0 and bulk/intr endpoints */
 583         writel (  (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
 584                     /* set NAK_OUT for erratum 0114 */
 585                 | ((ep->dev->chiprev == CHIPREV_1) << SET_NAK_OUT_PACKETS)
 586                 | (1 << SET_ENDPOINT_HALT)
 587                 , &ep->regs->ep_rsp);
 588 }
 589
 590 static inline void clear_halt (struct net2280_ep *ep)
 591 {
 592         /* ep0 and bulk/intr endpoints */
 593         writel (  (1 << CLEAR_ENDPOINT_HALT)
 594                 | (1 << CLEAR_ENDPOINT_TOGGLE)
 595                     /* unless the gadget driver left a short packet in the
 596                      * fifo, this reverses the erratum 0114 workaround.
 597                      */
 598                 | ((ep->dev->chiprev == CHIPREV_1) << CLEAR_NAK_OUT_PACKETS)
 599                 , &ep->regs->ep_rsp);
 600 }
 601
 602 #ifdef USE_RDK_LEDS
 603
 604 static inline void net2280_led_init (struct net2280 *dev)
 605 {
 606         /* LED3 (green) is on during USB activity. note erratum 0113. */
 607         writel ((1 << GPIO3_LED_SELECT)
 608                 | (1 << GPIO3_OUTPUT_ENABLE)
 609                 | (1 << GPIO2_OUTPUT_ENABLE)
 610                 | (1 << GPIO1_OUTPUT_ENABLE)
 611                 | (1 << GPIO0_OUTPUT_ENABLE)
 612                 , &dev->regs->gpioctl);
 613 }
 614
 615 /* indicate speed with bi-color LED 0/1 */
 616 static inline
 617 void net2280_led_speed (struct net2280 *dev, enum usb_device_speed speed)
 618 {
 619         u32     val = readl (&dev->regs->gpioctl);
 620         switch (speed) {
 621         case USB_SPEED_HIGH:            /* green */
 622                 val &= ~(1 << GPIO0_DATA);
 623                 val |= (1 << GPIO1_DATA);
 624                 break;
 625         case USB_SPEED_FULL:            /* red */
 626                 val &= ~(1 << GPIO1_DATA);
 627                 val |= (1 << GPIO0_DATA);
 628                 break;
 629         default:                        /* (off/black) */
 630                 val &= ~((1 << GPIO1_DATA) | (1 << GPIO0_DATA));
 631                 break;
 632         }
 633         writel (val, &dev->regs->gpioctl);
 634 }
 635
 636 /* indicate power with LED 2 */
 637 static inline void net2280_led_active (struct net2280 *dev, int is_active)
 638 {
 639         u32     val = readl (&dev->regs->gpioctl);
 640
 641         // FIXME this LED never seems to turn on.
 642         if (is_active)
 643                 val |= GPIO2_DATA;
 644         else
 645                 val &= ~GPIO2_DATA;
 646         writel (val, &dev->regs->gpioctl);
 647 }
 648 static inline void net2280_led_shutdown (struct net2280 *dev)
 649 {
 650         /* turn off all four GPIO*_DATA bits */
 651         writel (readl (&dev->regs->gpioctl) & ~0x0f,
 652                         &dev->regs->gpioctl);
 653 }
 654
 655 #else
 656
 657 #define net2280_led_init(dev)           do { } while (0)
 658 #define net2280_led_speed(dev, speed)   do { } while (0)
 659 #define net2280_led_shutdown(dev)       do { } while (0)
 660
 661 #endif
 662
 663 /*-------------------------------------------------------------------------*/
 664
 665 #define xprintk(dev,level,fmt,args...) \
 666         printk(level "%s %s: " fmt , driver_name , \
 667                         pci_name(dev->pdev) , ## args)
 668
 669 #ifdef DEBUG
 670 #undef DEBUG
 671 #define DEBUG(dev,fmt,args...) \
 672         xprintk(dev , KERN_DEBUG , fmt , ## args)
 673 #else
 674 #define DEBUG(dev,fmt,args...) \
 675         do { } while (0)
 676 #endif /* DEBUG */
 677
 678 #ifdef VERBOSE
 679 #define VDEBUG DEBUG
 680 #else
 681 #define VDEBUG(dev,fmt,args...) \
 682         do { } while (0)
 683 #endif  /* VERBOSE */
 684
 685 #define ERROR(dev,fmt,args...) \
 686         xprintk(dev , KERN_ERR , fmt , ## args)
 687 #define WARN(dev,fmt,args...) \
 688         xprintk(dev , KERN_WARNING , fmt , ## args)
 689 #define INFO(dev,fmt,args...) \
 690         xprintk(dev , KERN_INFO , fmt , ## args)
 691
 692 /*-------------------------------------------------------------------------*/
 693
 694 static inline void start_out_naking (struct net2280_ep *ep)
 695 {
 696         /* NOTE:  hardware races lurk here, and PING protocol issues */
 697         writel ((1 << SET_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
 698         /* synch with device */
 699         readl (&ep->regs->ep_rsp);
 700 }
 701
 702 #ifdef DEBUG
 703 static inline void assert_out_naking (struct net2280_ep *ep, const char *where)
 704 {
 705         u32     tmp = readl (&ep->regs->ep_stat);
 706
 707         if ((tmp & (1 << NAK_OUT_PACKETS)) == 0) {
 708                 DEBUG (ep->dev, "%s %s %08x !NAK\n",
 709                                 ep->ep.name, where, tmp);
 710                 writel ((1 << SET_NAK_OUT_PACKETS),
 711                         &ep->regs->ep_rsp);
 712         }
 713 }
 714 #define ASSERT_OUT_NAKING(ep) assert_out_naking(ep,__FUNCTION__)
 715 #else
 716 #define ASSERT_OUT_NAKING(ep) do {} while (0)
 717 #endif
 718
 719 static inline void stop_out_naking (struct net2280_ep *ep)
 720 {
 721         u32     tmp;
 722
 723         tmp = readl (&ep->regs->ep_stat);
 724         if ((tmp & (1 << NAK_OUT_PACKETS)) != 0)
 725                 writel ((1 << CLEAR_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
 726 }
 727
 728 #endif  /* __KERNEL__ */