Merge tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace...

[drm/drm-misc.git] / drivers / gpio / gpio-xilinx.c

// SPDX-License-Identifier: GPL-2.0-only
/*
 * Xilinx gpio driver for xps/axi_gpio IP.
 *
 * Copyright 2008 - 2013 Xilinx, Inc.
 */

#include <linux/bitmap.h>
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/errno.h>
#include <linux/gpio/driver.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/property.h>
#include <linux/slab.h>

/* Register Offset Definitions */
#define XGPIO_DATA_OFFSET   (0x0)       /* Data register  */
#define XGPIO_TRI_OFFSET    (0x4)       /* I/O direction register  */

#define XGPIO_CHANNEL0_OFFSET   0x0
#define XGPIO_CHANNEL1_OFFSET   0x8

#define XGPIO_GIER_OFFSET       0x11c /* Global Interrupt Enable */
#define XGPIO_GIER_IE           BIT(31)
#define XGPIO_IPISR_OFFSET      0x120 /* IP Interrupt Status */
#define XGPIO_IPIER_OFFSET      0x128 /* IP Interrupt Enable */

/* Read/Write access to the GPIO registers */
#if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_X86)
# define xgpio_readreg(offset)          readl(offset)
# define xgpio_writereg(offset, val)    writel(val, offset)
#else
# define xgpio_readreg(offset)          __raw_readl(offset)
# define xgpio_writereg(offset, val)    __raw_writel(val, offset)
#endif

/**
 * struct xgpio_instance - Stores information about GPIO device
 * @gc: GPIO chip
 * @regs: register block
 * @hw_map: GPIO pin mapping on hardware side
 * @sw_map: GPIO pin mapping on software side
 * @state: GPIO write state shadow register
 * @last_irq_read: GPIO read state register from last interrupt
 * @dir: GPIO direction shadow register
 * @gpio_lock: Lock used for synchronization
 * @irq: IRQ used by GPIO device
 * @enable: GPIO IRQ enable/disable bitfield
 * @rising_edge: GPIO IRQ rising edge enable/disable bitfield
 * @falling_edge: GPIO IRQ falling edge enable/disable bitfield
 * @clk: clock resource for this driver
 */
struct xgpio_instance {
        struct gpio_chip gc;
        void __iomem *regs;
        DECLARE_BITMAP(hw_map, 64);
        DECLARE_BITMAP(sw_map, 64);
        DECLARE_BITMAP(state, 64);
        DECLARE_BITMAP(last_irq_read, 64);
        DECLARE_BITMAP(dir, 64);
        spinlock_t gpio_lock;   /* For serializing operations */
        int irq;
        DECLARE_BITMAP(enable, 64);
        DECLARE_BITMAP(rising_edge, 64);
        DECLARE_BITMAP(falling_edge, 64);
        struct clk *clk;
};

static inline int xgpio_from_bit(struct xgpio_instance *chip, int bit)
{
        return bitmap_bitremap(bit, chip->hw_map, chip->sw_map, 64);
}

static inline int xgpio_to_bit(struct xgpio_instance *chip, int gpio)
{
        return bitmap_bitremap(gpio, chip->sw_map, chip->hw_map, 64);
}

static inline u32 xgpio_get_value32(const unsigned long *map, int bit)
{
        const size_t index = BIT_WORD(bit);
        const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5);

        return (map[index] >> offset) & 0xFFFFFFFFul;
}

static inline void xgpio_set_value32(unsigned long *map, int bit, u32 v)
{
        const size_t index = BIT_WORD(bit);
        const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5);

        map[index] &= ~(0xFFFFFFFFul << offset);
        map[index] |= (unsigned long)v << offset;
}

static inline int xgpio_regoffset(struct xgpio_instance *chip, int ch)
{
        switch (ch) {
        case 0:
                return XGPIO_CHANNEL0_OFFSET;
        case 1:
                return XGPIO_CHANNEL1_OFFSET;
        default:
                return -EINVAL;
        }
}

static void xgpio_read_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
{
        void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);

        xgpio_set_value32(a, bit, xgpio_readreg(addr));
}

static void xgpio_write_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a)
{
        void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32);

        xgpio_writereg(addr, xgpio_get_value32(a, bit));
}

static void xgpio_read_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a)
{
        int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1);

        for (bit = 0; bit <= lastbit ; bit += 32)
                xgpio_read_ch(chip, reg, bit, a);
}

static void xgpio_write_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a)
{
        int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1);

        for (bit = 0; bit <= lastbit ; bit += 32)
                xgpio_write_ch(chip, reg, bit, a);
}

/**
 * xgpio_get - Read the specified signal of the GPIO device.
 * @gc:     Pointer to gpio_chip device structure.
 * @gpio:   GPIO signal number.
 *
 * This function reads the specified signal of the GPIO device.
 *
 * Return:
 * 0 if direction of GPIO signals is set as input otherwise it
 * returns negative error value.
 */
static int xgpio_get(struct gpio_chip *gc, unsigned int gpio)
{
        struct xgpio_instance *chip = gpiochip_get_data(gc);
        int bit = xgpio_to_bit(chip, gpio);
        DECLARE_BITMAP(state, 64);

        xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, state);

        return test_bit(bit, state);
}

/**
 * xgpio_set - Write the specified signal of the GPIO device.
 * @gc:     Pointer to gpio_chip device structure.
 * @gpio:   GPIO signal number.
 * @val:    Value to be written to specified signal.
 *
 * This function writes the specified value in to the specified signal of the
 * GPIO device.
 */
static void xgpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
{
        unsigned long flags;
        struct xgpio_instance *chip = gpiochip_get_data(gc);
        int bit = xgpio_to_bit(chip, gpio);

        spin_lock_irqsave(&chip->gpio_lock, flags);

        /* Write to GPIO signal and set its direction to output */
        __assign_bit(bit, chip->state, val);

        xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state);

        spin_unlock_irqrestore(&chip->gpio_lock, flags);
}

/**
 * xgpio_set_multiple - Write the specified signals of the GPIO device.
 * @gc:     Pointer to gpio_chip device structure.
 * @mask:   Mask of the GPIOS to modify.
 * @bits:   Value to be wrote on each GPIO
 *
 * This function writes the specified values into the specified signals of the
 * GPIO devices.
 */
static void xgpio_set_multiple(struct gpio_chip *gc, unsigned long *mask,
                               unsigned long *bits)
{
        DECLARE_BITMAP(hw_mask, 64);
        DECLARE_BITMAP(hw_bits, 64);
        DECLARE_BITMAP(state, 64);
        unsigned long flags;
        struct xgpio_instance *chip = gpiochip_get_data(gc);

        bitmap_remap(hw_mask, mask, chip->sw_map, chip->hw_map, 64);
        bitmap_remap(hw_bits, bits, chip->sw_map, chip->hw_map, 64);

        spin_lock_irqsave(&chip->gpio_lock, flags);

        bitmap_replace(state, chip->state, hw_bits, hw_mask, 64);

        xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, state);

        bitmap_copy(chip->state, state, 64);

        spin_unlock_irqrestore(&chip->gpio_lock, flags);
}

/**
 * xgpio_dir_in - Set the direction of the specified GPIO signal as input.
 * @gc:     Pointer to gpio_chip device structure.
 * @gpio:   GPIO signal number.
 *
 * Return:
 * 0 - if direction of GPIO signals is set as input
 * otherwise it returns negative error value.
 */
static int xgpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
{
        unsigned long flags;
        struct xgpio_instance *chip = gpiochip_get_data(gc);
        int bit = xgpio_to_bit(chip, gpio);

        spin_lock_irqsave(&chip->gpio_lock, flags);

        /* Set the GPIO bit in shadow register and set direction as input */
        __set_bit(bit, chip->dir);
        xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);

        spin_unlock_irqrestore(&chip->gpio_lock, flags);

        return 0;
}

/**
 * xgpio_dir_out - Set the direction of the specified GPIO signal as output.
 * @gc:     Pointer to gpio_chip device structure.
 * @gpio:   GPIO signal number.
 * @val:    Value to be written to specified signal.
 *
 * This function sets the direction of specified GPIO signal as output.
 *
 * Return:
 * If all GPIO signals of GPIO chip is configured as input then it returns
 * error otherwise it returns 0.
 */
static int xgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
{
        unsigned long flags;
        struct xgpio_instance *chip = gpiochip_get_data(gc);
        int bit = xgpio_to_bit(chip, gpio);

        spin_lock_irqsave(&chip->gpio_lock, flags);

        /* Write state of GPIO signal */
        __assign_bit(bit, chip->state, val);
        xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state);

        /* Clear the GPIO bit in shadow register and set direction as output */
        __clear_bit(bit, chip->dir);
        xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir);

        spin_unlock_irqrestore(&chip->gpio_lock, flags);

        return 0;
}

/**
 * xgpio_save_regs - Set initial values of GPIO pins
 * @chip: Pointer to GPIO instance
 */
static void xgpio_save_regs(struct xgpio_instance *chip)
{
        xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, chip->state);
        xgpio_write_ch_all(chip, XGPIO_TRI_OFFSET, chip->dir);
}

static int xgpio_request(struct gpio_chip *chip, unsigned int offset)
{
        int ret;

        ret = pm_runtime_get_sync(chip->parent);
        /*
         * If the device is already active pm_runtime_get() will return 1 on
         * success, but gpio_request still needs to return 0.
         */
        return ret < 0 ? ret : 0;
}

static void xgpio_free(struct gpio_chip *chip, unsigned int offset)
{
        pm_runtime_put(chip->parent);
}

static int __maybe_unused xgpio_suspend(struct device *dev)
{
        struct xgpio_instance *gpio = dev_get_drvdata(dev);
        struct irq_data *data = irq_get_irq_data(gpio->irq);

        if (!data) {
                dev_dbg(dev, "IRQ not connected\n");
                return pm_runtime_force_suspend(dev);
        }

        if (!irqd_is_wakeup_set(data))
                return pm_runtime_force_suspend(dev);

        return 0;
}

/**
 * xgpio_remove - Remove method for the GPIO device.
 * @pdev: pointer to the platform device
 *
 * This function remove gpiochips and frees all the allocated resources.
 *
 * Return: 0 always
 */
static void xgpio_remove(struct platform_device *pdev)
{
        pm_runtime_get_sync(&pdev->dev);
        pm_runtime_put_noidle(&pdev->dev);
        pm_runtime_disable(&pdev->dev);
}

/**
 * xgpio_irq_ack - Acknowledge a child GPIO interrupt.
 * @irq_data: per IRQ and chip data passed down to chip functions
 * This currently does nothing, but irq_ack is unconditionally called by
 * handle_edge_irq and therefore must be defined.
 */
static void xgpio_irq_ack(struct irq_data *irq_data)
{
}

static int __maybe_unused xgpio_resume(struct device *dev)
{
        struct xgpio_instance *gpio = dev_get_drvdata(dev);
        struct irq_data *data = irq_get_irq_data(gpio->irq);

        if (!data) {
                dev_dbg(dev, "IRQ not connected\n");
                return pm_runtime_force_resume(dev);
        }

        if (!irqd_is_wakeup_set(data))
                return pm_runtime_force_resume(dev);

        return 0;
}

static int __maybe_unused xgpio_runtime_suspend(struct device *dev)
{
        struct xgpio_instance *gpio = dev_get_drvdata(dev);

        clk_disable(gpio->clk);

        return 0;
}

static int __maybe_unused xgpio_runtime_resume(struct device *dev)
{
        struct xgpio_instance *gpio = dev_get_drvdata(dev);

        return clk_enable(gpio->clk);
}

static const struct dev_pm_ops xgpio_dev_pm_ops = {
        SET_SYSTEM_SLEEP_PM_OPS(xgpio_suspend, xgpio_resume)
        SET_RUNTIME_PM_OPS(xgpio_runtime_suspend,
                           xgpio_runtime_resume, NULL)
};

/**
 * xgpio_irq_mask - Write the specified signal of the GPIO device.
 * @irq_data: per IRQ and chip data passed down to chip functions
 */
static void xgpio_irq_mask(struct irq_data *irq_data)
{
        unsigned long flags;
        struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
        int irq_offset = irqd_to_hwirq(irq_data);
        int bit = xgpio_to_bit(chip, irq_offset);
        u32 mask = BIT(bit / 32), temp;

        spin_lock_irqsave(&chip->gpio_lock, flags);

        __clear_bit(bit, chip->enable);

        if (xgpio_get_value32(chip->enable, bit) == 0) {
                /* Disable per channel interrupt */
                temp = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET);
                temp &= ~mask;
                xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, temp);
        }
        spin_unlock_irqrestore(&chip->gpio_lock, flags);

        gpiochip_disable_irq(&chip->gc, irq_offset);
}

/**
 * xgpio_irq_unmask - Write the specified signal of the GPIO device.
 * @irq_data: per IRQ and chip data passed down to chip functions
 */
static void xgpio_irq_unmask(struct irq_data *irq_data)
{
        unsigned long flags;
        struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
        int irq_offset = irqd_to_hwirq(irq_data);
        int bit = xgpio_to_bit(chip, irq_offset);
        u32 old_enable = xgpio_get_value32(chip->enable, bit);
        u32 mask = BIT(bit / 32), val;

        gpiochip_enable_irq(&chip->gc, irq_offset);

        spin_lock_irqsave(&chip->gpio_lock, flags);

        __set_bit(bit, chip->enable);

        if (old_enable == 0) {
                /* Clear any existing per-channel interrupts */
                val = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
                val &= mask;
                xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, val);

                /* Update GPIO IRQ read data before enabling interrupt*/
                xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, chip->last_irq_read);

                /* Enable per channel interrupt */
                val = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET);
                val |= mask;
                xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, val);
        }

        spin_unlock_irqrestore(&chip->gpio_lock, flags);
}

/**
 * xgpio_set_irq_type - Write the specified signal of the GPIO device.
 * @irq_data: Per IRQ and chip data passed down to chip functions
 * @type: Interrupt type that is to be set for the gpio pin
 *
 * Return:
 * 0 if interrupt type is supported otherwise -EINVAL
 */
static int xgpio_set_irq_type(struct irq_data *irq_data, unsigned int type)
{
        struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data);
        int irq_offset = irqd_to_hwirq(irq_data);
        int bit = xgpio_to_bit(chip, irq_offset);

        /*
         * The Xilinx GPIO hardware provides a single interrupt status
         * indication for any state change in a given GPIO channel (bank).
         * Therefore, only rising edge or falling edge triggers are
         * supported.
         */
        switch (type & IRQ_TYPE_SENSE_MASK) {
        case IRQ_TYPE_EDGE_BOTH:
                __set_bit(bit, chip->rising_edge);
                __set_bit(bit, chip->falling_edge);
                break;
        case IRQ_TYPE_EDGE_RISING:
                __set_bit(bit, chip->rising_edge);
                __clear_bit(bit, chip->falling_edge);
                break;
        case IRQ_TYPE_EDGE_FALLING:
                __clear_bit(bit, chip->rising_edge);
                __set_bit(bit, chip->falling_edge);
                break;
        default:
                return -EINVAL;
        }

        irq_set_handler_locked(irq_data, handle_edge_irq);
        return 0;
}

/**
 * xgpio_irqhandler - Gpio interrupt service routine
 * @desc: Pointer to interrupt description
 */
static void xgpio_irqhandler(struct irq_desc *desc)
{
        struct xgpio_instance *chip = irq_desc_get_handler_data(desc);
        struct gpio_chip *gc = &chip->gc;
        struct irq_chip *irqchip = irq_desc_get_chip(desc);
        DECLARE_BITMAP(rising, 64);
        DECLARE_BITMAP(falling, 64);
        DECLARE_BITMAP(all, 64);
        int irq_offset;
        u32 status;
        u32 bit;

        status = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
        xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, status);

        chained_irq_enter(irqchip, desc);

        spin_lock(&chip->gpio_lock);

        xgpio_read_ch_all(chip, XGPIO_DATA_OFFSET, all);

        bitmap_complement(rising, chip->last_irq_read, 64);
        bitmap_and(rising, rising, all, 64);
        bitmap_and(rising, rising, chip->enable, 64);
        bitmap_and(rising, rising, chip->rising_edge, 64);

        bitmap_complement(falling, all, 64);
        bitmap_and(falling, falling, chip->last_irq_read, 64);
        bitmap_and(falling, falling, chip->enable, 64);
        bitmap_and(falling, falling, chip->falling_edge, 64);

        bitmap_copy(chip->last_irq_read, all, 64);
        bitmap_or(all, rising, falling, 64);

        spin_unlock(&chip->gpio_lock);

        dev_dbg(gc->parent, "IRQ rising %*pb falling %*pb\n", 64, rising, 64, falling);

        for_each_set_bit(bit, all, 64) {
                irq_offset = xgpio_from_bit(chip, bit);
                generic_handle_domain_irq(gc->irq.domain, irq_offset);
        }

        chained_irq_exit(irqchip, desc);
}

static const struct irq_chip xgpio_irq_chip = {
        .name = "gpio-xilinx",
        .irq_ack = xgpio_irq_ack,
        .irq_mask = xgpio_irq_mask,
        .irq_unmask = xgpio_irq_unmask,
        .irq_set_type = xgpio_set_irq_type,
        .flags = IRQCHIP_IMMUTABLE,
        GPIOCHIP_IRQ_RESOURCE_HELPERS,
};

/**
 * xgpio_probe - Probe method for the GPIO device.
 * @pdev: pointer to the platform device
 *
 * Return:
 * It returns 0, if the driver is bound to the GPIO device, or
 * a negative value if there is an error.
 */
static int xgpio_probe(struct platform_device *pdev)
{
        struct device *dev = &pdev->dev;
        struct xgpio_instance *chip;
        int status = 0;
        u32 is_dual = 0;
        u32 width[2];
        u32 state[2];
        u32 dir[2];
        struct gpio_irq_chip *girq;
        u32 temp;

        chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
        if (!chip)
                return -ENOMEM;

        platform_set_drvdata(pdev, chip);

        /* First, check if the device is dual-channel */
        device_property_read_u32(dev, "xlnx,is-dual", &is_dual);

        /* Setup defaults */
        memset32(width, 0, ARRAY_SIZE(width));
        memset32(state, 0, ARRAY_SIZE(state));
        memset32(dir, 0xFFFFFFFF, ARRAY_SIZE(dir));

        /* Update GPIO state shadow register with default value */
        device_property_read_u32(dev, "xlnx,dout-default", &state[0]);
        device_property_read_u32(dev, "xlnx,dout-default-2", &state[1]);

        bitmap_from_arr32(chip->state, state, 64);

        /* Update GPIO direction shadow register with default value */
        device_property_read_u32(dev, "xlnx,tri-default", &dir[0]);
        device_property_read_u32(dev, "xlnx,tri-default-2", &dir[1]);

        bitmap_from_arr32(chip->dir, dir, 64);

        /*
         * Check device node and parent device node for device width
         * and assume default width of 32
         */
        if (device_property_read_u32(dev, "xlnx,gpio-width", &width[0]))
                width[0] = 32;

        if (width[0] > 32)
                return -EINVAL;

        if (is_dual && device_property_read_u32(dev, "xlnx,gpio2-width", &width[1]))
                width[1] = 32;

        if (width[1] > 32)
                return -EINVAL;

        /* Setup software pin mapping */
        bitmap_set(chip->sw_map, 0, width[0] + width[1]);

        /* Setup hardware pin mapping */
        bitmap_set(chip->hw_map,  0, width[0]);
        bitmap_set(chip->hw_map, 32, width[1]);

        spin_lock_init(&chip->gpio_lock);

        chip->gc.base = -1;
        chip->gc.ngpio = bitmap_weight(chip->hw_map, 64);
        chip->gc.parent = dev;
        chip->gc.direction_input = xgpio_dir_in;
        chip->gc.direction_output = xgpio_dir_out;
        chip->gc.get = xgpio_get;
        chip->gc.set = xgpio_set;
        chip->gc.request = xgpio_request;
        chip->gc.free = xgpio_free;
        chip->gc.set_multiple = xgpio_set_multiple;

        chip->gc.label = dev_name(dev);

        chip->regs = devm_platform_ioremap_resource(pdev, 0);
        if (IS_ERR(chip->regs)) {
                dev_err(dev, "failed to ioremap memory resource\n");
                return PTR_ERR(chip->regs);
        }

        chip->clk = devm_clk_get_optional_enabled(dev, NULL);
        if (IS_ERR(chip->clk))
                return dev_err_probe(dev, PTR_ERR(chip->clk), "input clock not found.\n");

        pm_runtime_get_noresume(dev);
        pm_runtime_set_active(dev);
        pm_runtime_enable(dev);

        xgpio_save_regs(chip);

        chip->irq = platform_get_irq_optional(pdev, 0);
        if (chip->irq <= 0)
                goto skip_irq;

        /* Disable per-channel interrupts */
        xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, 0);
        /* Clear any existing per-channel interrupts */
        temp = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET);
        xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, temp);
        /* Enable global interrupts */
        xgpio_writereg(chip->regs + XGPIO_GIER_OFFSET, XGPIO_GIER_IE);

        girq = &chip->gc.irq;
        gpio_irq_chip_set_chip(girq, &xgpio_irq_chip);
        girq->parent_handler = xgpio_irqhandler;
        girq->num_parents = 1;
        girq->parents = devm_kcalloc(dev, 1, sizeof(*girq->parents),
                                     GFP_KERNEL);
        if (!girq->parents) {
                status = -ENOMEM;
                goto err_pm_put;
        }
        girq->parents[0] = chip->irq;
        girq->default_type = IRQ_TYPE_NONE;
        girq->handler = handle_bad_irq;

skip_irq:
        status = devm_gpiochip_add_data(dev, &chip->gc, chip);
        if (status) {
                dev_err(dev, "failed to add GPIO chip\n");
                goto err_pm_put;
        }

        pm_runtime_put(dev);
        return 0;

err_pm_put:
        pm_runtime_disable(dev);
        pm_runtime_put_noidle(dev);
        return status;
}

static const struct of_device_id xgpio_of_match[] = {
        { .compatible = "xlnx,xps-gpio-1.00.a", },
        { /* end of list */ },
};

MODULE_DEVICE_TABLE(of, xgpio_of_match);

static struct platform_driver xgpio_plat_driver = {
        .probe          = xgpio_probe,
        .remove         = xgpio_remove,
        .driver         = {
                        .name = "gpio-xilinx",
                        .of_match_table = xgpio_of_match,
                        .pm = &xgpio_dev_pm_ops,
        },
};

static int __init xgpio_init(void)
{
        return platform_driver_register(&xgpio_plat_driver);
}

subsys_initcall(xgpio_init);

static void __exit xgpio_exit(void)
{
        platform_driver_unregister(&xgpio_plat_driver);
}
module_exit(xgpio_exit);

MODULE_AUTHOR("Xilinx, Inc.");
MODULE_DESCRIPTION("Xilinx GPIO driver");
MODULE_LICENSE("GPL");