Merge tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace...

[drm/drm-misc.git] / drivers / misc / eeprom / at24.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * at24.c - handle most I2C EEPROMs
 *
 * Copyright (C) 2005-2007 David Brownell
 * Copyright (C) 2008 Wolfram Sang, Pengutronix
 */

#include <linux/acpi.h>
#include <linux/bitops.h>
#include <linux/capability.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/nvmem-provider.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/pm_runtime.h>
#include <linux/property.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/slab.h>

/* Address pointer is 16 bit. */
#define AT24_FLAG_ADDR16        BIT(7)
/* sysfs-entry will be read-only. */
#define AT24_FLAG_READONLY      BIT(6)
/* sysfs-entry will be world-readable. */
#define AT24_FLAG_IRUGO         BIT(5)
/* Take always 8 addresses (24c00). */
#define AT24_FLAG_TAKE8ADDR     BIT(4)
/* Factory-programmed serial number. */
#define AT24_FLAG_SERIAL        BIT(3)
/* Factory-programmed mac address. */
#define AT24_FLAG_MAC           BIT(2)
/* Does not auto-rollover reads to the next slave address. */
#define AT24_FLAG_NO_RDROL      BIT(1)

/*
 * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
 * Differences between different vendor product lines (like Atmel AT24C or
 * MicroChip 24LC, etc) won't much matter for typical read/write access.
 * There are also I2C RAM chips, likewise interchangeable. One example
 * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes).
 *
 * However, misconfiguration can lose data. "Set 16-bit memory address"
 * to a part with 8-bit addressing will overwrite data. Writing with too
 * big a page size also loses data. And it's not safe to assume that the
 * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC
 * uses 0x51, for just one example.
 *
 * Accordingly, explicit board-specific configuration data should be used
 * in almost all cases. (One partial exception is an SMBus used to access
 * "SPD" data for DRAM sticks. Those only use 24c02 EEPROMs.)
 *
 * So this driver uses "new style" I2C driver binding, expecting to be
 * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or
 * similar kernel-resident tables; or, configuration data coming from
 * a bootloader.
 *
 * Other than binding model, current differences from "eeprom" driver are
 * that this one handles write access and isn't restricted to 24c02 devices.
 * It also handles larger devices (32 kbit and up) with two-byte addresses,
 * which won't work on pure SMBus systems.
 */

struct at24_data {
        /*
         * Lock protects against activities from other Linux tasks,
         * but not from changes by other I2C masters.
         */
        struct mutex lock;

        unsigned int write_max;
        unsigned int num_addresses;
        unsigned int offset_adj;

        u32 byte_len;
        u16 page_size;
        u8 flags;

        struct nvmem_device *nvmem;
        struct regulator *vcc_reg;
        void (*read_post)(unsigned int off, char *buf, size_t count);

        /*
         * Some chips tie up multiple I2C addresses; dummy devices reserve
         * them for us.
         */
        u8 bank_addr_shift;
        struct regmap *client_regmaps[] __counted_by(num_addresses);
};

/*
 * This parameter is to help this driver avoid blocking other drivers out
 * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C
 * clock, one 256 byte read takes about 1/43 second which is excessive;
 * but the 1/170 second it takes at 400 kHz may be quite reasonable; and
 * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible.
 *
 * This value is forced to be a power of two so that writes align on pages.
 */
static unsigned int at24_io_limit = 128;
module_param_named(io_limit, at24_io_limit, uint, 0);
MODULE_PARM_DESC(at24_io_limit, "Maximum bytes per I/O (default 128)");

/*
 * Specs often allow 5 msec for a page write, sometimes 20 msec;
 * it's important to recover from write timeouts.
 */
static unsigned int at24_write_timeout = 25;
module_param_named(write_timeout, at24_write_timeout, uint, 0);
MODULE_PARM_DESC(at24_write_timeout, "Time (in ms) to try writes (default 25)");

struct at24_chip_data {
        u32 byte_len;
        u8 flags;
        u8 bank_addr_shift;
        void (*read_post)(unsigned int off, char *buf, size_t count);
};

#define AT24_CHIP_DATA(_name, _len, _flags)                             \
        static const struct at24_chip_data _name = {                    \
                .byte_len = _len, .flags = _flags,                      \
        }

#define AT24_CHIP_DATA_CB(_name, _len, _flags, _read_post)              \
        static const struct at24_chip_data _name = {                    \
                .byte_len = _len, .flags = _flags,                      \
                .read_post = _read_post,                                \
        }

#define AT24_CHIP_DATA_BS(_name, _len, _flags, _bank_addr_shift)        \
        static const struct at24_chip_data _name = {                    \
                .byte_len = _len, .flags = _flags,                      \
                .bank_addr_shift = _bank_addr_shift                     \
        }

static void at24_read_post_vaio(unsigned int off, char *buf, size_t count)
{
        int i;

        if (capable(CAP_SYS_ADMIN))
                return;

        /*
         * Hide VAIO private settings to regular users:
         * - BIOS passwords: bytes 0x00 to 0x0f
         * - UUID: bytes 0x10 to 0x1f
         * - Serial number: 0xc0 to 0xdf
         */
        for (i = 0; i < count; i++) {
                if ((off + i <= 0x1f) ||
                    (off + i >= 0xc0 && off + i <= 0xdf))
                        buf[i] = 0;
        }
}

/* needs 8 addresses as A0-A2 are ignored */
AT24_CHIP_DATA(at24_data_24c00, 128 / 8, AT24_FLAG_TAKE8ADDR);
/* old variants can't be handled with this generic entry! */
AT24_CHIP_DATA(at24_data_24c01, 1024 / 8, 0);
AT24_CHIP_DATA(at24_data_24cs01, 16,
        AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24c02, 2048 / 8, 0);
AT24_CHIP_DATA(at24_data_24cs02, 16,
        AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24mac402, 48 / 8,
        AT24_FLAG_MAC | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24mac602, 64 / 8,
        AT24_FLAG_MAC | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24aa025e48, 48 / 8,
        AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24aa025e64, 64 / 8,
        AT24_FLAG_READONLY);
/* spd is a 24c02 in memory DIMMs */
AT24_CHIP_DATA(at24_data_spd, 2048 / 8,
        AT24_FLAG_READONLY | AT24_FLAG_IRUGO);
/* 24c02_vaio is a 24c02 on some Sony laptops */
AT24_CHIP_DATA_CB(at24_data_24c02_vaio, 2048 / 8,
        AT24_FLAG_READONLY | AT24_FLAG_IRUGO,
        at24_read_post_vaio);
AT24_CHIP_DATA(at24_data_24c04, 4096 / 8, 0);
AT24_CHIP_DATA(at24_data_24cs04, 16,
        AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
/* 24rf08 quirk is handled at i2c-core */
AT24_CHIP_DATA(at24_data_24c08, 8192 / 8, 0);
AT24_CHIP_DATA(at24_data_24cs08, 16,
        AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24c16, 16384 / 8, 0);
AT24_CHIP_DATA(at24_data_24cs16, 16,
        AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24c32, 32768 / 8, AT24_FLAG_ADDR16);
/* M24C32-D Additional Write lockable page (M24C32-D order codes) */
AT24_CHIP_DATA(at24_data_24c32d_wlp, 32, AT24_FLAG_ADDR16);
AT24_CHIP_DATA(at24_data_24cs32, 16,
        AT24_FLAG_ADDR16 | AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24c64, 65536 / 8, AT24_FLAG_ADDR16);
/* M24C64-D Additional Write lockable page (M24C64-D order codes) */
AT24_CHIP_DATA(at24_data_24c64d_wlp, 32, AT24_FLAG_ADDR16);
AT24_CHIP_DATA(at24_data_24cs64, 16,
        AT24_FLAG_ADDR16 | AT24_FLAG_SERIAL | AT24_FLAG_READONLY);
AT24_CHIP_DATA(at24_data_24c128, 131072 / 8, AT24_FLAG_ADDR16);
AT24_CHIP_DATA(at24_data_24c256, 262144 / 8, AT24_FLAG_ADDR16);
/* M24256E Additional Write lockable page (M24256E-F order codes) */
AT24_CHIP_DATA(at24_data_24256e_wlp, 64, AT24_FLAG_ADDR16);
AT24_CHIP_DATA(at24_data_24c512, 524288 / 8, AT24_FLAG_ADDR16);
AT24_CHIP_DATA(at24_data_24c1024, 1048576 / 8, AT24_FLAG_ADDR16);
AT24_CHIP_DATA_BS(at24_data_24c1025, 1048576 / 8, AT24_FLAG_ADDR16, 2);
AT24_CHIP_DATA(at24_data_24c2048, 2097152 / 8, AT24_FLAG_ADDR16);
/* identical to 24c08 ? */
AT24_CHIP_DATA(at24_data_INT3499, 8192 / 8, 0);

static const struct i2c_device_id at24_ids[] = {
        { "24c00",      (kernel_ulong_t)&at24_data_24c00 },
        { "24c01",      (kernel_ulong_t)&at24_data_24c01 },
        { "24cs01",     (kernel_ulong_t)&at24_data_24cs01 },
        { "24c02",      (kernel_ulong_t)&at24_data_24c02 },
        { "24cs02",     (kernel_ulong_t)&at24_data_24cs02 },
        { "24mac402",   (kernel_ulong_t)&at24_data_24mac402 },
        { "24mac602",   (kernel_ulong_t)&at24_data_24mac602 },
        { "24aa025e48", (kernel_ulong_t)&at24_data_24aa025e48 },
        { "24aa025e64", (kernel_ulong_t)&at24_data_24aa025e64 },
        { "spd",        (kernel_ulong_t)&at24_data_spd },
        { "24c02-vaio", (kernel_ulong_t)&at24_data_24c02_vaio },
        { "24c04",      (kernel_ulong_t)&at24_data_24c04 },
        { "24cs04",     (kernel_ulong_t)&at24_data_24cs04 },
        { "24c08",      (kernel_ulong_t)&at24_data_24c08 },
        { "24cs08",     (kernel_ulong_t)&at24_data_24cs08 },
        { "24c16",      (kernel_ulong_t)&at24_data_24c16 },
        { "24cs16",     (kernel_ulong_t)&at24_data_24cs16 },
        { "24c32",      (kernel_ulong_t)&at24_data_24c32 },
        { "24c32d-wl",  (kernel_ulong_t)&at24_data_24c32d_wlp },
        { "24cs32",     (kernel_ulong_t)&at24_data_24cs32 },
        { "24c64",      (kernel_ulong_t)&at24_data_24c64 },
        { "24c64-wl",   (kernel_ulong_t)&at24_data_24c64d_wlp },
        { "24cs64",     (kernel_ulong_t)&at24_data_24cs64 },
        { "24c128",     (kernel_ulong_t)&at24_data_24c128 },
        { "24c256",     (kernel_ulong_t)&at24_data_24c256 },
        { "24256e-wl",  (kernel_ulong_t)&at24_data_24256e_wlp },
        { "24c512",     (kernel_ulong_t)&at24_data_24c512 },
        { "24c1024",    (kernel_ulong_t)&at24_data_24c1024 },
        { "24c1025",    (kernel_ulong_t)&at24_data_24c1025 },
        { "24c2048",    (kernel_ulong_t)&at24_data_24c2048 },
        { "at24",       0 },
        { /* END OF LIST */ }
};
MODULE_DEVICE_TABLE(i2c, at24_ids);

static const struct of_device_id __maybe_unused at24_of_match[] = {
        { .compatible = "atmel,24c00",          .data = &at24_data_24c00 },
        { .compatible = "atmel,24c01",          .data = &at24_data_24c01 },
        { .compatible = "atmel,24cs01",         .data = &at24_data_24cs01 },
        { .compatible = "atmel,24c02",          .data = &at24_data_24c02 },
        { .compatible = "atmel,24cs02",         .data = &at24_data_24cs02 },
        { .compatible = "atmel,24mac402",       .data = &at24_data_24mac402 },
        { .compatible = "atmel,24mac602",       .data = &at24_data_24mac602 },
        { .compatible = "atmel,spd",            .data = &at24_data_spd },
        { .compatible = "atmel,24c04",          .data = &at24_data_24c04 },
        { .compatible = "atmel,24cs04",         .data = &at24_data_24cs04 },
        { .compatible = "atmel,24c08",          .data = &at24_data_24c08 },
        { .compatible = "atmel,24cs08",         .data = &at24_data_24cs08 },
        { .compatible = "atmel,24c16",          .data = &at24_data_24c16 },
        { .compatible = "atmel,24cs16",         .data = &at24_data_24cs16 },
        { .compatible = "atmel,24c32",          .data = &at24_data_24c32 },
        { .compatible = "atmel,24c32d-wl",      .data = &at24_data_24c32d_wlp },
        { .compatible = "atmel,24cs32",         .data = &at24_data_24cs32 },
        { .compatible = "atmel,24c64",          .data = &at24_data_24c64 },
        { .compatible = "atmel,24c64d-wl",      .data = &at24_data_24c64d_wlp },
        { .compatible = "atmel,24cs64",         .data = &at24_data_24cs64 },
        { .compatible = "atmel,24c128",         .data = &at24_data_24c128 },
        { .compatible = "atmel,24c256",         .data = &at24_data_24c256 },
        { .compatible = "atmel,24c512",         .data = &at24_data_24c512 },
        { .compatible = "atmel,24c1024",        .data = &at24_data_24c1024 },
        { .compatible = "atmel,24c1025",        .data = &at24_data_24c1025 },
        { .compatible = "atmel,24c2048",        .data = &at24_data_24c2048 },
        { .compatible = "microchip,24aa025e48", .data = &at24_data_24aa025e48 },
        { .compatible = "microchip,24aa025e64", .data = &at24_data_24aa025e64 },
        { .compatible = "st,24256e-wl",         .data = &at24_data_24256e_wlp },
        { /* END OF LIST */ },
};
MODULE_DEVICE_TABLE(of, at24_of_match);

static const struct acpi_device_id __maybe_unused at24_acpi_ids[] = {
        { "INT3499",    (kernel_ulong_t)&at24_data_INT3499 },
        { "TPF0001",    (kernel_ulong_t)&at24_data_24c1024 },
        { /* END OF LIST */ }
};
MODULE_DEVICE_TABLE(acpi, at24_acpi_ids);

/*
 * This routine supports chips which consume multiple I2C addresses. It
 * computes the addressing information to be used for a given r/w request.
 * Assumes that sanity checks for offset happened at sysfs-layer.
 *
 * Slave address and byte offset derive from the offset. Always
 * set the byte address; on a multi-master board, another master
 * may have changed the chip's "current" address pointer.
 */
static struct regmap *at24_translate_offset(struct at24_data *at24,
                                            unsigned int *offset)
{
        unsigned int i;

        if (at24->flags & AT24_FLAG_ADDR16) {
                i = *offset >> 16;
                *offset &= 0xffff;
        } else {
                i = *offset >> 8;
                *offset &= 0xff;
        }

        return at24->client_regmaps[i];
}

static struct device *at24_base_client_dev(struct at24_data *at24)
{
        return regmap_get_device(at24->client_regmaps[0]);
}

static size_t at24_adjust_read_count(struct at24_data *at24,
                                      unsigned int offset, size_t count)
{
        unsigned int bits;
        size_t remainder;

        /*
         * In case of multi-address chips that don't rollover reads to
         * the next slave address: truncate the count to the slave boundary,
         * so that the read never straddles slaves.
         */
        if (at24->flags & AT24_FLAG_NO_RDROL) {
                bits = (at24->flags & AT24_FLAG_ADDR16) ? 16 : 8;
                remainder = BIT(bits) - offset;
                if (count > remainder)
                        count = remainder;
        }

        if (count > at24_io_limit)
                count = at24_io_limit;

        return count;
}

static ssize_t at24_regmap_read(struct at24_data *at24, char *buf,
                                unsigned int offset, size_t count)
{
        unsigned long timeout, read_time;
        struct regmap *regmap;
        int ret;

        regmap = at24_translate_offset(at24, &offset);
        count = at24_adjust_read_count(at24, offset, count);

        /* adjust offset for mac and serial read ops */
        offset += at24->offset_adj;

        timeout = jiffies + msecs_to_jiffies(at24_write_timeout);
        do {
                /*
                 * The timestamp shall be taken before the actual operation
                 * to avoid a premature timeout in case of high CPU load.
                 */
                read_time = jiffies;

                ret = regmap_bulk_read(regmap, offset, buf, count);
                dev_dbg(regmap_get_device(regmap), "read %zu@%d --> %d (%ld)\n",
                        count, offset, ret, jiffies);
                if (!ret)
                        return count;

                usleep_range(1000, 1500);
        } while (time_before(read_time, timeout));

        return -ETIMEDOUT;
}

/*
 * Note that if the hardware write-protect pin is pulled high, the whole
 * chip is normally write protected. But there are plenty of product
 * variants here, including OTP fuses and partial chip protect.
 *
 * We only use page mode writes; the alternative is sloooow. These routines
 * write at most one page.
 */

static size_t at24_adjust_write_count(struct at24_data *at24,
                                      unsigned int offset, size_t count)
{
        unsigned int next_page;

        /* write_max is at most a page */
        if (count > at24->write_max)
                count = at24->write_max;

        /* Never roll over backwards, to the start of this page */
        next_page = roundup(offset + 1, at24->page_size);
        if (offset + count > next_page)
                count = next_page - offset;

        return count;
}

static ssize_t at24_regmap_write(struct at24_data *at24, const char *buf,
                                 unsigned int offset, size_t count)
{
        unsigned long timeout, write_time;
        struct regmap *regmap;
        int ret;

        regmap = at24_translate_offset(at24, &offset);
        count = at24_adjust_write_count(at24, offset, count);
        timeout = jiffies + msecs_to_jiffies(at24_write_timeout);

        do {
                /*
                 * The timestamp shall be taken before the actual operation
                 * to avoid a premature timeout in case of high CPU load.
                 */
                write_time = jiffies;

                ret = regmap_bulk_write(regmap, offset, buf, count);
                dev_dbg(regmap_get_device(regmap), "write %zu@%d --> %d (%ld)\n",
                        count, offset, ret, jiffies);
                if (!ret)
                        return count;

                usleep_range(1000, 1500);
        } while (time_before(write_time, timeout));

        return -ETIMEDOUT;
}

static int at24_read(void *priv, unsigned int off, void *val, size_t count)
{
        struct at24_data *at24;
        struct device *dev;
        char *buf = val;
        int i, ret;

        at24 = priv;
        dev = at24_base_client_dev(at24);

        if (unlikely(!count))
                return count;

        if (off + count > at24->byte_len)
                return -EINVAL;

        ret = pm_runtime_resume_and_get(dev);
        if (ret)
                return ret;
        /*
         * Read data from chip, protecting against concurrent updates
         * from this host, but not from other I2C masters.
         */
        mutex_lock(&at24->lock);

        for (i = 0; count; i += ret, count -= ret) {
                ret = at24_regmap_read(at24, buf + i, off + i, count);
                if (ret < 0) {
                        mutex_unlock(&at24->lock);
                        pm_runtime_put(dev);
                        return ret;
                }
        }

        mutex_unlock(&at24->lock);

        pm_runtime_put(dev);

        if (unlikely(at24->read_post))
                at24->read_post(off, buf, i);

        return 0;
}

static int at24_write(void *priv, unsigned int off, void *val, size_t count)
{
        struct at24_data *at24;
        struct device *dev;
        char *buf = val;
        int ret;

        at24 = priv;
        dev = at24_base_client_dev(at24);

        if (unlikely(!count))
                return -EINVAL;

        if (off + count > at24->byte_len)
                return -EINVAL;

        ret = pm_runtime_resume_and_get(dev);
        if (ret)
                return ret;
        /*
         * Write data to chip, protecting against concurrent updates
         * from this host, but not from other I2C masters.
         */
        mutex_lock(&at24->lock);

        while (count) {
                ret = at24_regmap_write(at24, buf, off, count);
                if (ret < 0) {
                        mutex_unlock(&at24->lock);
                        pm_runtime_put(dev);
                        return ret;
                }
                buf += ret;
                off += ret;
                count -= ret;
        }

        mutex_unlock(&at24->lock);

        pm_runtime_put(dev);

        return 0;
}

static int at24_make_dummy_client(struct at24_data *at24, unsigned int index,
                                  struct i2c_client *base_client,
                                  struct regmap_config *regmap_config)
{
        struct i2c_client *dummy_client;
        struct regmap *regmap;

        dummy_client = devm_i2c_new_dummy_device(&base_client->dev,
                                                 base_client->adapter,
                                                 base_client->addr +
                                                 (index << at24->bank_addr_shift));
        if (IS_ERR(dummy_client))
                return PTR_ERR(dummy_client);

        regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
        if (IS_ERR(regmap))
                return PTR_ERR(regmap);

        at24->client_regmaps[index] = regmap;

        return 0;
}

static unsigned int at24_get_offset_adj(u8 flags, unsigned int byte_len)
{
        if (flags & AT24_FLAG_MAC) {
                /* EUI-48 starts from 0x9a, EUI-64 from 0x98 */
                return 0xa0 - byte_len;
        } else if (flags & AT24_FLAG_SERIAL && flags & AT24_FLAG_ADDR16) {
                /*
                 * For 16 bit address pointers, the word address must contain
                 * a '10' sequence in bits 11 and 10 regardless of the
                 * intended position of the address pointer.
                 */
                return 0x0800;
        } else if (flags & AT24_FLAG_SERIAL) {
                /*
                 * Otherwise the word address must begin with a '10' sequence,
                 * regardless of the intended address.
                 */
                return 0x0080;
        } else {
                return 0;
        }
}

static void at24_probe_temp_sensor(struct i2c_client *client)
{
        struct at24_data *at24 = i2c_get_clientdata(client);
        struct i2c_board_info info = { .type = "jc42" };
        int ret;
        u8 val;

        /*
         * Byte 2 has value 11 for DDR3, earlier versions don't
         * support the thermal sensor present flag
         */
        ret = at24_read(at24, 2, &val, 1);
        if (ret || val != 11)
                return;

        /* Byte 32, bit 7 is set if temp sensor is present */
        ret = at24_read(at24, 32, &val, 1);
        if (ret || !(val & BIT(7)))
                return;

        info.addr = 0x18 | (client->addr & 7);

        i2c_new_client_device(client->adapter, &info);
}

static int at24_probe(struct i2c_client *client)
{
        struct regmap_config regmap_config = { };
        struct nvmem_config nvmem_config = { };
        u32 byte_len, page_size, flags, addrw;
        const struct at24_chip_data *cdata;
        struct device *dev = &client->dev;
        bool i2c_fn_i2c, i2c_fn_block;
        unsigned int i, num_addresses;
        struct at24_data *at24;
        bool full_power;
        struct regmap *regmap;
        bool writable;
        u8 test_byte;
        int err;

        i2c_fn_i2c = i2c_check_functionality(client->adapter, I2C_FUNC_I2C);
        i2c_fn_block = i2c_check_functionality(client->adapter,
                                               I2C_FUNC_SMBUS_WRITE_I2C_BLOCK);

        cdata = i2c_get_match_data(client);
        if (!cdata)
                return -ENODEV;

        err = device_property_read_u32(dev, "pagesize", &page_size);
        if (err)
                /*
                 * This is slow, but we can't know all eeproms, so we better
                 * play safe. Specifying custom eeprom-types via device tree
                 * or properties is recommended anyhow.
                 */
                page_size = 1;

        flags = cdata->flags;
        if (device_property_present(dev, "read-only"))
                flags |= AT24_FLAG_READONLY;
        if (device_property_present(dev, "no-read-rollover"))
                flags |= AT24_FLAG_NO_RDROL;

        err = device_property_read_u32(dev, "address-width", &addrw);
        if (!err) {
                switch (addrw) {
                case 8:
                        if (flags & AT24_FLAG_ADDR16)
                                dev_warn(dev,
                                         "Override address width to be 8, while default is 16\n");
                        flags &= ~AT24_FLAG_ADDR16;
                        break;
                case 16:
                        flags |= AT24_FLAG_ADDR16;
                        break;
                default:
                        dev_warn(dev, "Bad \"address-width\" property: %u\n",
                                 addrw);
                }
        }

        err = device_property_read_u32(dev, "size", &byte_len);
        if (err)
                byte_len = cdata->byte_len;

        if (!i2c_fn_i2c && !i2c_fn_block)
                page_size = 1;

        if (!page_size) {
                dev_err(dev, "page_size must not be 0!\n");
                return -EINVAL;
        }

        if (!is_power_of_2(page_size))
                dev_warn(dev, "page_size looks suspicious (no power of 2)!\n");

        err = device_property_read_u32(dev, "num-addresses", &num_addresses);
        if (err) {
                if (flags & AT24_FLAG_TAKE8ADDR)
                        num_addresses = 8;
                else
                        num_addresses = DIV_ROUND_UP(byte_len,
                                (flags & AT24_FLAG_ADDR16) ? 65536 : 256);
        }

        if ((flags & AT24_FLAG_SERIAL) && (flags & AT24_FLAG_MAC)) {
                dev_err(dev,
                        "invalid device data - cannot have both AT24_FLAG_SERIAL & AT24_FLAG_MAC.");
                return -EINVAL;
        }

        regmap_config.val_bits = 8;
        regmap_config.reg_bits = (flags & AT24_FLAG_ADDR16) ? 16 : 8;
        regmap_config.disable_locking = true;

        regmap = devm_regmap_init_i2c(client, &regmap_config);
        if (IS_ERR(regmap))
                return PTR_ERR(regmap);

        at24 = devm_kzalloc(dev, struct_size(at24, client_regmaps, num_addresses),
                            GFP_KERNEL);
        if (!at24)
                return -ENOMEM;

        mutex_init(&at24->lock);
        at24->byte_len = byte_len;
        at24->page_size = page_size;
        at24->flags = flags;
        at24->read_post = cdata->read_post;
        at24->bank_addr_shift = cdata->bank_addr_shift;
        at24->num_addresses = num_addresses;
        at24->offset_adj = at24_get_offset_adj(flags, byte_len);
        at24->client_regmaps[0] = regmap;

        at24->vcc_reg = devm_regulator_get(dev, "vcc");
        if (IS_ERR(at24->vcc_reg))
                return PTR_ERR(at24->vcc_reg);

        writable = !(flags & AT24_FLAG_READONLY);
        if (writable) {
                at24->write_max = min_t(unsigned int,
                                        page_size, at24_io_limit);
                if (!i2c_fn_i2c && at24->write_max > I2C_SMBUS_BLOCK_MAX)
                        at24->write_max = I2C_SMBUS_BLOCK_MAX;
        }

        /* use dummy devices for multiple-address chips */
        for (i = 1; i < num_addresses; i++) {
                err = at24_make_dummy_client(at24, i, client, &regmap_config);
                if (err)
                        return err;
        }

        /*
         * We initialize nvmem_config.id to NVMEM_DEVID_AUTO even if the
         * label property is set as some platform can have multiple eeproms
         * with same label and we can not register each of those with same
         * label. Failing to register those eeproms trigger cascade failure
         * on such platform.
         */
        nvmem_config.id = NVMEM_DEVID_AUTO;

        if (device_property_present(dev, "label")) {
                err = device_property_read_string(dev, "label",
                                                  &nvmem_config.name);
                if (err)
                        return err;
        } else {
                nvmem_config.name = dev_name(dev);
        }

        nvmem_config.type = NVMEM_TYPE_EEPROM;
        nvmem_config.dev = dev;
        nvmem_config.read_only = !writable;
        nvmem_config.root_only = !(flags & AT24_FLAG_IRUGO);
        nvmem_config.owner = THIS_MODULE;
        nvmem_config.compat = true;
        nvmem_config.base_dev = dev;
        nvmem_config.reg_read = at24_read;
        nvmem_config.reg_write = at24_write;
        nvmem_config.priv = at24;
        nvmem_config.stride = 1;
        nvmem_config.word_size = 1;
        nvmem_config.size = byte_len;

        i2c_set_clientdata(client, at24);

        full_power = acpi_dev_state_d0(&client->dev);
        if (full_power) {
                err = regulator_enable(at24->vcc_reg);
                if (err) {
                        dev_err(dev, "Failed to enable vcc regulator\n");
                        return err;
                }

                pm_runtime_set_active(dev);
        }
        pm_runtime_enable(dev);

        /*
         * Perform a one-byte test read to verify that the chip is functional,
         * unless powering on the device is to be avoided during probe (i.e.
         * it's powered off right now).
         */
        if (full_power) {
                err = at24_read(at24, 0, &test_byte, 1);
                if (err) {
                        pm_runtime_disable(dev);
                        if (!pm_runtime_status_suspended(dev))
                                regulator_disable(at24->vcc_reg);
                        return -ENODEV;
                }
        }

        at24->nvmem = devm_nvmem_register(dev, &nvmem_config);
        if (IS_ERR(at24->nvmem)) {
                pm_runtime_disable(dev);
                if (!pm_runtime_status_suspended(dev))
                        regulator_disable(at24->vcc_reg);
                return dev_err_probe(dev, PTR_ERR(at24->nvmem),
                                     "failed to register nvmem\n");
        }

        /* If this a SPD EEPROM, probe for DDR3 thermal sensor */
        if (cdata == &at24_data_spd)
                at24_probe_temp_sensor(client);

        pm_runtime_idle(dev);

        if (writable)
                dev_info(dev, "%u byte %s EEPROM, writable, %u bytes/write\n",
                         byte_len, client->name, at24->write_max);
        else
                dev_info(dev, "%u byte %s EEPROM, read-only\n",
                         byte_len, client->name);

        return 0;
}

static void at24_remove(struct i2c_client *client)
{
        struct at24_data *at24 = i2c_get_clientdata(client);

        pm_runtime_disable(&client->dev);
        if (acpi_dev_state_d0(&client->dev)) {
                if (!pm_runtime_status_suspended(&client->dev))
                        regulator_disable(at24->vcc_reg);
                pm_runtime_set_suspended(&client->dev);
        }
}

static int __maybe_unused at24_suspend(struct device *dev)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct at24_data *at24 = i2c_get_clientdata(client);

        return regulator_disable(at24->vcc_reg);
}

static int __maybe_unused at24_resume(struct device *dev)
{
        struct i2c_client *client = to_i2c_client(dev);
        struct at24_data *at24 = i2c_get_clientdata(client);

        return regulator_enable(at24->vcc_reg);
}

static const struct dev_pm_ops at24_pm_ops = {
        SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
                                pm_runtime_force_resume)
        SET_RUNTIME_PM_OPS(at24_suspend, at24_resume, NULL)
};

static struct i2c_driver at24_driver = {
        .driver = {
                .name = "at24",
                .pm = &at24_pm_ops,
                .of_match_table = of_match_ptr(at24_of_match),
                .acpi_match_table = ACPI_PTR(at24_acpi_ids),
        },
        .probe = at24_probe,
        .remove = at24_remove,
        .id_table = at24_ids,
        .flags = I2C_DRV_ACPI_WAIVE_D0_PROBE,
};

static int __init at24_init(void)
{
        if (!at24_io_limit) {
                pr_err("at24: at24_io_limit must not be 0!\n");
                return -EINVAL;
        }

        at24_io_limit = rounddown_pow_of_two(at24_io_limit);
        return i2c_add_driver(&at24_driver);
}
module_init(at24_init);

static void __exit at24_exit(void)
{
        i2c_del_driver(&at24_driver);
}
module_exit(at24_exit);

MODULE_DESCRIPTION("Driver for most I2C EEPROMs");
MODULE_AUTHOR("David Brownell and Wolfram Sang");
MODULE_LICENSE("GPL");