1 // SPDX-License-Identifier: GPL-2.0-only
3 * TI TRF7970a RFID/NFC Transceiver Driver
5 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
7 * Author: Erick Macias <emacias@ti.com>
8 * Author: Felipe Balbi <balbi@ti.com>
9 * Author: Mark A. Greer <mgreer@animalcreek.com>
12 #include <linux/module.h>
13 #include <linux/device.h>
14 #include <linux/netdevice.h>
15 #include <linux/interrupt.h>
16 #include <linux/pm_runtime.h>
17 #include <linux/nfc.h>
18 #include <linux/skbuff.h>
19 #include <linux/delay.h>
20 #include <linux/gpio/consumer.h>
22 #include <linux/spi/spi.h>
23 #include <linux/regulator/consumer.h>
25 #include <net/nfc/nfc.h>
26 #include <net/nfc/digital.h>
28 /* There are 3 ways the host can communicate with the trf7970a:
29 * parallel mode, SPI with Slave Select (SS) mode, and SPI without
30 * SS mode. The driver only supports the two SPI modes.
32 * The trf7970a is very timing sensitive and the VIN, EN2, and EN
33 * pins must asserted in that order and with specific delays in between.
34 * The delays used in the driver were provided by TI and have been
35 * confirmed to work with this driver. There is a bug with the current
36 * version of the trf7970a that requires that EN2 remain low no matter
37 * what. If it goes high, it will generate an RF field even when in
38 * passive target mode. TI has indicated that the chip will work okay
39 * when EN2 is left low. The 'en2-rf-quirk' device tree property
40 * indicates that trf7970a currently being used has the erratum and
41 * that EN2 must be kept low.
43 * Timeouts are implemented using the delayed workqueue kernel facility.
44 * Timeouts are required so things don't hang when there is no response
45 * from the trf7970a (or tag). Using this mechanism creates a race with
46 * interrupts, however. That is, an interrupt and a timeout could occur
47 * closely enough together that one is blocked by the mutex while the other
48 * executes. When the timeout handler executes first and blocks the
49 * interrupt handler, it will eventually set the state to IDLE so the
50 * interrupt handler will check the state and exit with no harm done.
51 * When the interrupt handler executes first and blocks the timeout handler,
52 * the cancel_delayed_work() call will know that it didn't cancel the
53 * work item (i.e., timeout) and will return zero. That return code is
54 * used by the timer handler to indicate that it should ignore the timeout
57 * Aborting an active command isn't as simple as it seems because the only
58 * way to abort a command that's already been sent to the tag is so turn
59 * off power to the tag. If we do that, though, we'd have to go through
60 * the entire anticollision procedure again but the digital layer doesn't
61 * support that. So, if an abort is received before trf7970a_send_cmd()
62 * has sent the command to the tag, it simply returns -ECANCELED. If the
63 * command has already been sent to the tag, then the driver continues
64 * normally and recieves the response data (or error) but just before
65 * sending the data upstream, it frees the rx_skb and sends -ECANCELED
66 * upstream instead. If the command failed, that error will be sent
69 * When recieving data from a tag and the interrupt status register has
70 * only the SRX bit set, it means that all of the data has been received
71 * (once what's in the fifo has been read). However, depending on timing
72 * an interrupt status with only the SRX bit set may not be recived. In
73 * those cases, the timeout mechanism is used to wait 20 ms in case more
74 * data arrives. After 20 ms, it is assumed that all of the data has been
75 * received and the accumulated rx data is sent upstream. The
76 * 'TRF7970A_ST_WAIT_FOR_RX_DATA_CONT' state is used for this purpose
77 * (i.e., it indicates that some data has been received but we're not sure
78 * if there is more coming so a timeout in this state means all data has
79 * been received and there isn't an error). The delay is 20 ms since delays
80 * of ~16 ms have been observed during testing.
82 * When transmitting a frame larger than the FIFO size (127 bytes), the
83 * driver will wait 20 ms for the FIFO to drain past the low-watermark
84 * and generate an interrupt. The low-watermark set to 32 bytes so the
85 * interrupt should fire after 127 - 32 = 95 bytes have been sent. At
86 * the lowest possible bit rate (6.62 kbps for 15693), it will take up
87 * to ~14.35 ms so 20 ms is used for the timeout.
89 * Type 2 write and sector select commands respond with a 4-bit ACK or NACK.
90 * Having only 4 bits in the FIFO won't normally generate an interrupt so
91 * driver enables the '4_bit_RX' bit of the Special Functions register 1
92 * to cause an interrupt in that case. Leaving that bit for a read command
93 * messes up the data returned so it is only enabled when the framing is
94 * 'NFC_DIGITAL_FRAMING_NFCA_T2T' and the command is not a read command.
95 * Unfortunately, that means that the driver has to peek into tx frames
96 * when the framing is 'NFC_DIGITAL_FRAMING_NFCA_T2T'. This is done by
97 * the trf7970a_per_cmd_config() routine.
99 * ISO/IEC 15693 frames specify whether to use single or double sub-carrier
100 * frequencies and whether to use low or high data rates in the flags byte
101 * of the frame. This means that the driver has to peek at all 15693 frames
102 * to determine what speed to set the communication to. In addition, write
103 * and lock commands use the OPTION flag to indicate that an EOF must be
104 * sent to the tag before it will send its response. So the driver has to
105 * examine all frames for that reason too.
107 * It is unclear how long to wait before sending the EOF. According to the
108 * Note under Table 1-1 in section 1.6 of
109 * http://www.ti.com/lit/ug/scbu011/scbu011.pdf, that wait should be at least
110 * 10 ms for TI Tag-it HF-I tags; however testing has shown that is not long
111 * enough so 20 ms is used. So the timer is set to 40 ms - 20 ms to drain
112 * up to 127 bytes in the FIFO at the lowest bit rate plus another 20 ms to
113 * ensure the wait is long enough before sending the EOF. This seems to work
117 #define TRF7970A_SUPPORTED_PROTOCOLS \
118 (NFC_PROTO_MIFARE_MASK | NFC_PROTO_ISO14443_MASK | \
119 NFC_PROTO_ISO14443_B_MASK | NFC_PROTO_FELICA_MASK | \
120 NFC_PROTO_ISO15693_MASK | NFC_PROTO_NFC_DEP_MASK)
122 #define TRF7970A_AUTOSUSPEND_DELAY 30000 /* 30 seconds */
123 #define TRF7970A_13MHZ_CLOCK_FREQUENCY 13560000
124 #define TRF7970A_27MHZ_CLOCK_FREQUENCY 27120000
126 #define TRF7970A_RX_SKB_ALLOC_SIZE 256
128 #define TRF7970A_FIFO_SIZE 127
130 /* TX length is 3 nibbles long ==> 4KB - 1 bytes max */
131 #define TRF7970A_TX_MAX (4096 - 1)
133 #define TRF7970A_WAIT_FOR_TX_IRQ 20
134 #define TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT 20
135 #define TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT 20
136 #define TRF7970A_WAIT_TO_ISSUE_ISO15693_EOF 40
138 /* Guard times for various RF technologies (in us) */
139 #define TRF7970A_GUARD_TIME_NFCA 5000
140 #define TRF7970A_GUARD_TIME_NFCB 5000
141 #define TRF7970A_GUARD_TIME_NFCF 20000
142 #define TRF7970A_GUARD_TIME_15693 1000
145 /* Erratum: When reading IRQ Status register on trf7970a, we must issue a
146 * read continuous command for IRQ Status and Collision Position registers.
148 #define TRF7970A_QUIRK_IRQ_STATUS_READ BIT(0)
149 #define TRF7970A_QUIRK_EN2_MUST_STAY_LOW BIT(1)
151 /* Direct commands */
152 #define TRF7970A_CMD_IDLE 0x00
153 #define TRF7970A_CMD_SOFT_INIT 0x03
154 #define TRF7970A_CMD_RF_COLLISION 0x04
155 #define TRF7970A_CMD_RF_COLLISION_RESPONSE_N 0x05
156 #define TRF7970A_CMD_RF_COLLISION_RESPONSE_0 0x06
157 #define TRF7970A_CMD_FIFO_RESET 0x0f
158 #define TRF7970A_CMD_TRANSMIT_NO_CRC 0x10
159 #define TRF7970A_CMD_TRANSMIT 0x11
160 #define TRF7970A_CMD_DELAY_TRANSMIT_NO_CRC 0x12
161 #define TRF7970A_CMD_DELAY_TRANSMIT 0x13
162 #define TRF7970A_CMD_EOF 0x14
163 #define TRF7970A_CMD_CLOSE_SLOT 0x15
164 #define TRF7970A_CMD_BLOCK_RX 0x16
165 #define TRF7970A_CMD_ENABLE_RX 0x17
166 #define TRF7970A_CMD_TEST_INT_RF 0x18
167 #define TRF7970A_CMD_TEST_EXT_RF 0x19
168 #define TRF7970A_CMD_RX_GAIN_ADJUST 0x1a
170 /* Bits determining whether its a direct command or register R/W,
171 * whether to use a continuous SPI transaction or not, and the actual
172 * direct cmd opcode or register address.
174 #define TRF7970A_CMD_BIT_CTRL BIT(7)
175 #define TRF7970A_CMD_BIT_RW BIT(6)
176 #define TRF7970A_CMD_BIT_CONTINUOUS BIT(5)
177 #define TRF7970A_CMD_BIT_OPCODE(opcode) ((opcode) & 0x1f)
179 /* Registers addresses */
180 #define TRF7970A_CHIP_STATUS_CTRL 0x00
181 #define TRF7970A_ISO_CTRL 0x01
182 #define TRF7970A_ISO14443B_TX_OPTIONS 0x02
183 #define TRF7970A_ISO14443A_HIGH_BITRATE_OPTIONS 0x03
184 #define TRF7970A_TX_TIMER_SETTING_H_BYTE 0x04
185 #define TRF7970A_TX_TIMER_SETTING_L_BYTE 0x05
186 #define TRF7970A_TX_PULSE_LENGTH_CTRL 0x06
187 #define TRF7970A_RX_NO_RESPONSE_WAIT 0x07
188 #define TRF7970A_RX_WAIT_TIME 0x08
189 #define TRF7970A_MODULATOR_SYS_CLK_CTRL 0x09
190 #define TRF7970A_RX_SPECIAL_SETTINGS 0x0a
191 #define TRF7970A_REG_IO_CTRL 0x0b
192 #define TRF7970A_IRQ_STATUS 0x0c
193 #define TRF7970A_COLLISION_IRQ_MASK 0x0d
194 #define TRF7970A_COLLISION_POSITION 0x0e
195 #define TRF7970A_RSSI_OSC_STATUS 0x0f
196 #define TRF7970A_SPECIAL_FCN_REG1 0x10
197 #define TRF7970A_SPECIAL_FCN_REG2 0x11
198 #define TRF7970A_RAM1 0x12
199 #define TRF7970A_RAM2 0x13
200 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS 0x14
201 #define TRF7970A_NFC_LOW_FIELD_LEVEL 0x16
202 #define TRF7970A_NFCID1 0x17
203 #define TRF7970A_NFC_TARGET_LEVEL 0x18
204 #define TRF79070A_NFC_TARGET_PROTOCOL 0x19
205 #define TRF7970A_TEST_REGISTER1 0x1a
206 #define TRF7970A_TEST_REGISTER2 0x1b
207 #define TRF7970A_FIFO_STATUS 0x1c
208 #define TRF7970A_TX_LENGTH_BYTE1 0x1d
209 #define TRF7970A_TX_LENGTH_BYTE2 0x1e
210 #define TRF7970A_FIFO_IO_REGISTER 0x1f
212 /* Chip Status Control Register Bits */
213 #define TRF7970A_CHIP_STATUS_VRS5_3 BIT(0)
214 #define TRF7970A_CHIP_STATUS_REC_ON BIT(1)
215 #define TRF7970A_CHIP_STATUS_AGC_ON BIT(2)
216 #define TRF7970A_CHIP_STATUS_PM_ON BIT(3)
217 #define TRF7970A_CHIP_STATUS_RF_PWR BIT(4)
218 #define TRF7970A_CHIP_STATUS_RF_ON BIT(5)
219 #define TRF7970A_CHIP_STATUS_DIRECT BIT(6)
220 #define TRF7970A_CHIP_STATUS_STBY BIT(7)
222 /* ISO Control Register Bits */
223 #define TRF7970A_ISO_CTRL_15693_SGL_1OF4_662 0x00
224 #define TRF7970A_ISO_CTRL_15693_SGL_1OF256_662 0x01
225 #define TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648 0x02
226 #define TRF7970A_ISO_CTRL_15693_SGL_1OF256_2648 0x03
227 #define TRF7970A_ISO_CTRL_15693_DBL_1OF4_667a 0x04
228 #define TRF7970A_ISO_CTRL_15693_DBL_1OF256_667 0x05
229 #define TRF7970A_ISO_CTRL_15693_DBL_1OF4_2669 0x06
230 #define TRF7970A_ISO_CTRL_15693_DBL_1OF256_2669 0x07
231 #define TRF7970A_ISO_CTRL_14443A_106 0x08
232 #define TRF7970A_ISO_CTRL_14443A_212 0x09
233 #define TRF7970A_ISO_CTRL_14443A_424 0x0a
234 #define TRF7970A_ISO_CTRL_14443A_848 0x0b
235 #define TRF7970A_ISO_CTRL_14443B_106 0x0c
236 #define TRF7970A_ISO_CTRL_14443B_212 0x0d
237 #define TRF7970A_ISO_CTRL_14443B_424 0x0e
238 #define TRF7970A_ISO_CTRL_14443B_848 0x0f
239 #define TRF7970A_ISO_CTRL_FELICA_212 0x1a
240 #define TRF7970A_ISO_CTRL_FELICA_424 0x1b
241 #define TRF7970A_ISO_CTRL_NFC_NFCA_106 0x01
242 #define TRF7970A_ISO_CTRL_NFC_NFCF_212 0x02
243 #define TRF7970A_ISO_CTRL_NFC_NFCF_424 0x03
244 #define TRF7970A_ISO_CTRL_NFC_CE_14443A 0x00
245 #define TRF7970A_ISO_CTRL_NFC_CE_14443B 0x01
246 #define TRF7970A_ISO_CTRL_NFC_CE BIT(2)
247 #define TRF7970A_ISO_CTRL_NFC_ACTIVE BIT(3)
248 #define TRF7970A_ISO_CTRL_NFC_INITIATOR BIT(4)
249 #define TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE BIT(5)
250 #define TRF7970A_ISO_CTRL_RFID BIT(5)
251 #define TRF7970A_ISO_CTRL_DIR_MODE BIT(6)
252 #define TRF7970A_ISO_CTRL_RX_CRC_N BIT(7) /* true == No CRC */
254 #define TRF7970A_ISO_CTRL_RFID_SPEED_MASK 0x1f
256 /* Modulator and SYS_CLK Control Register Bits */
257 #define TRF7970A_MODULATOR_DEPTH(n) ((n) & 0x7)
258 #define TRF7970A_MODULATOR_DEPTH_ASK10 (TRF7970A_MODULATOR_DEPTH(0))
259 #define TRF7970A_MODULATOR_DEPTH_OOK (TRF7970A_MODULATOR_DEPTH(1))
260 #define TRF7970A_MODULATOR_DEPTH_ASK7 (TRF7970A_MODULATOR_DEPTH(2))
261 #define TRF7970A_MODULATOR_DEPTH_ASK8_5 (TRF7970A_MODULATOR_DEPTH(3))
262 #define TRF7970A_MODULATOR_DEPTH_ASK13 (TRF7970A_MODULATOR_DEPTH(4))
263 #define TRF7970A_MODULATOR_DEPTH_ASK16 (TRF7970A_MODULATOR_DEPTH(5))
264 #define TRF7970A_MODULATOR_DEPTH_ASK22 (TRF7970A_MODULATOR_DEPTH(6))
265 #define TRF7970A_MODULATOR_DEPTH_ASK30 (TRF7970A_MODULATOR_DEPTH(7))
266 #define TRF7970A_MODULATOR_EN_ANA BIT(3)
267 #define TRF7970A_MODULATOR_CLK(n) (((n) & 0x3) << 4)
268 #define TRF7970A_MODULATOR_CLK_DISABLED (TRF7970A_MODULATOR_CLK(0))
269 #define TRF7970A_MODULATOR_CLK_3_6 (TRF7970A_MODULATOR_CLK(1))
270 #define TRF7970A_MODULATOR_CLK_6_13 (TRF7970A_MODULATOR_CLK(2))
271 #define TRF7970A_MODULATOR_CLK_13_27 (TRF7970A_MODULATOR_CLK(3))
272 #define TRF7970A_MODULATOR_EN_OOK BIT(6)
273 #define TRF7970A_MODULATOR_27MHZ BIT(7)
275 #define TRF7970A_RX_SPECIAL_SETTINGS_NO_LIM BIT(0)
276 #define TRF7970A_RX_SPECIAL_SETTINGS_AGCR BIT(1)
277 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_0DB (0x0 << 2)
278 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_5DB (0x1 << 2)
279 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_10DB (0x2 << 2)
280 #define TRF7970A_RX_SPECIAL_SETTINGS_GD_15DB (0x3 << 2)
281 #define TRF7970A_RX_SPECIAL_SETTINGS_HBT BIT(4)
282 #define TRF7970A_RX_SPECIAL_SETTINGS_M848 BIT(5)
283 #define TRF7970A_RX_SPECIAL_SETTINGS_C424 BIT(6)
284 #define TRF7970A_RX_SPECIAL_SETTINGS_C212 BIT(7)
286 #define TRF7970A_REG_IO_CTRL_VRS(v) ((v) & 0x07)
287 #define TRF7970A_REG_IO_CTRL_IO_LOW BIT(5)
288 #define TRF7970A_REG_IO_CTRL_EN_EXT_PA BIT(6)
289 #define TRF7970A_REG_IO_CTRL_AUTO_REG BIT(7)
291 /* IRQ Status Register Bits */
292 #define TRF7970A_IRQ_STATUS_NORESP BIT(0) /* ISO15693 only */
293 #define TRF7970A_IRQ_STATUS_NFC_COL_ERROR BIT(0)
294 #define TRF7970A_IRQ_STATUS_COL BIT(1)
295 #define TRF7970A_IRQ_STATUS_FRAMING_EOF_ERROR BIT(2)
296 #define TRF7970A_IRQ_STATUS_NFC_RF BIT(2)
297 #define TRF7970A_IRQ_STATUS_PARITY_ERROR BIT(3)
298 #define TRF7970A_IRQ_STATUS_NFC_SDD BIT(3)
299 #define TRF7970A_IRQ_STATUS_CRC_ERROR BIT(4)
300 #define TRF7970A_IRQ_STATUS_NFC_PROTO_ERROR BIT(4)
301 #define TRF7970A_IRQ_STATUS_FIFO BIT(5)
302 #define TRF7970A_IRQ_STATUS_SRX BIT(6)
303 #define TRF7970A_IRQ_STATUS_TX BIT(7)
305 #define TRF7970A_IRQ_STATUS_ERROR \
306 (TRF7970A_IRQ_STATUS_COL | \
307 TRF7970A_IRQ_STATUS_FRAMING_EOF_ERROR | \
308 TRF7970A_IRQ_STATUS_PARITY_ERROR | \
309 TRF7970A_IRQ_STATUS_CRC_ERROR)
311 #define TRF7970A_RSSI_OSC_STATUS_RSSI_MASK (BIT(2) | BIT(1) | BIT(0))
312 #define TRF7970A_RSSI_OSC_STATUS_RSSI_X_MASK (BIT(5) | BIT(4) | BIT(3))
313 #define TRF7970A_RSSI_OSC_STATUS_RSSI_OSC_OK BIT(6)
315 #define TRF7970A_SPECIAL_FCN_REG1_COL_7_6 BIT(0)
316 #define TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL BIT(1)
317 #define TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX BIT(2)
318 #define TRF7970A_SPECIAL_FCN_REG1_SP_DIR_MODE BIT(3)
319 #define TRF7970A_SPECIAL_FCN_REG1_NEXT_SLOT_37US BIT(4)
320 #define TRF7970A_SPECIAL_FCN_REG1_PAR43 BIT(5)
322 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_124 (0x0 << 2)
323 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_120 (0x1 << 2)
324 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_112 (0x2 << 2)
325 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96 (0x3 << 2)
326 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_4 0x0
327 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_8 0x1
328 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_16 0x2
329 #define TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32 0x3
331 #define TRF7970A_NFC_LOW_FIELD_LEVEL_RFDET(v) ((v) & 0x07)
332 #define TRF7970A_NFC_LOW_FIELD_LEVEL_CLEX_DIS BIT(7)
334 #define TRF7970A_NFC_TARGET_LEVEL_RFDET(v) ((v) & 0x07)
335 #define TRF7970A_NFC_TARGET_LEVEL_HI_RF BIT(3)
336 #define TRF7970A_NFC_TARGET_LEVEL_SDD_EN BIT(5)
337 #define TRF7970A_NFC_TARGET_LEVEL_LD_S_4BYTES (0x0 << 6)
338 #define TRF7970A_NFC_TARGET_LEVEL_LD_S_7BYTES (0x1 << 6)
339 #define TRF7970A_NFC_TARGET_LEVEL_LD_S_10BYTES (0x2 << 6)
341 #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106 BIT(0)
342 #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_212 BIT(1)
343 #define TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_424 (BIT(0) | BIT(1))
344 #define TRF79070A_NFC_TARGET_PROTOCOL_PAS_14443B BIT(2)
345 #define TRF79070A_NFC_TARGET_PROTOCOL_PAS_106 BIT(3)
346 #define TRF79070A_NFC_TARGET_PROTOCOL_FELICA BIT(4)
347 #define TRF79070A_NFC_TARGET_PROTOCOL_RF_L BIT(6)
348 #define TRF79070A_NFC_TARGET_PROTOCOL_RF_H BIT(7)
350 #define TRF79070A_NFC_TARGET_PROTOCOL_106A \
351 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
352 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
353 TRF79070A_NFC_TARGET_PROTOCOL_PAS_106 | \
354 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106)
356 #define TRF79070A_NFC_TARGET_PROTOCOL_106B \
357 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
358 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
359 TRF79070A_NFC_TARGET_PROTOCOL_PAS_14443B | \
360 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_106)
362 #define TRF79070A_NFC_TARGET_PROTOCOL_212F \
363 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
364 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
365 TRF79070A_NFC_TARGET_PROTOCOL_FELICA | \
366 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_212)
368 #define TRF79070A_NFC_TARGET_PROTOCOL_424F \
369 (TRF79070A_NFC_TARGET_PROTOCOL_RF_H | \
370 TRF79070A_NFC_TARGET_PROTOCOL_RF_L | \
371 TRF79070A_NFC_TARGET_PROTOCOL_FELICA | \
372 TRF79070A_NFC_TARGET_PROTOCOL_NFCBR_424)
374 #define TRF7970A_FIFO_STATUS_OVERFLOW BIT(7)
376 /* NFC (ISO/IEC 14443A) Type 2 Tag commands */
377 #define NFC_T2T_CMD_READ 0x30
379 /* ISO 15693 commands codes */
380 #define ISO15693_CMD_INVENTORY 0x01
381 #define ISO15693_CMD_READ_SINGLE_BLOCK 0x20
382 #define ISO15693_CMD_WRITE_SINGLE_BLOCK 0x21
383 #define ISO15693_CMD_LOCK_BLOCK 0x22
384 #define ISO15693_CMD_READ_MULTIPLE_BLOCK 0x23
385 #define ISO15693_CMD_WRITE_MULTIPLE_BLOCK 0x24
386 #define ISO15693_CMD_SELECT 0x25
387 #define ISO15693_CMD_RESET_TO_READY 0x26
388 #define ISO15693_CMD_WRITE_AFI 0x27
389 #define ISO15693_CMD_LOCK_AFI 0x28
390 #define ISO15693_CMD_WRITE_DSFID 0x29
391 #define ISO15693_CMD_LOCK_DSFID 0x2a
392 #define ISO15693_CMD_GET_SYSTEM_INFO 0x2b
393 #define ISO15693_CMD_GET_MULTIPLE_BLOCK_SECURITY_STATUS 0x2c
395 /* ISO 15693 request and response flags */
396 #define ISO15693_REQ_FLAG_SUB_CARRIER BIT(0)
397 #define ISO15693_REQ_FLAG_DATA_RATE BIT(1)
398 #define ISO15693_REQ_FLAG_INVENTORY BIT(2)
399 #define ISO15693_REQ_FLAG_PROTOCOL_EXT BIT(3)
400 #define ISO15693_REQ_FLAG_SELECT BIT(4)
401 #define ISO15693_REQ_FLAG_AFI BIT(4)
402 #define ISO15693_REQ_FLAG_ADDRESS BIT(5)
403 #define ISO15693_REQ_FLAG_NB_SLOTS BIT(5)
404 #define ISO15693_REQ_FLAG_OPTION BIT(6)
406 #define ISO15693_REQ_FLAG_SPEED_MASK \
407 (ISO15693_REQ_FLAG_SUB_CARRIER | ISO15693_REQ_FLAG_DATA_RATE)
409 enum trf7970a_state
{
413 TRF7970A_ST_IDLE_RX_BLOCKED
,
414 TRF7970A_ST_WAIT_FOR_TX_FIFO
,
415 TRF7970A_ST_WAIT_FOR_RX_DATA
,
416 TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
,
417 TRF7970A_ST_WAIT_TO_ISSUE_EOF
,
418 TRF7970A_ST_LISTENING
,
419 TRF7970A_ST_LISTENING_MD
,
424 enum trf7970a_state state
;
426 struct spi_device
*spi
;
427 struct regulator
*vin_regulator
;
428 struct regulator
*vddio_regulator
;
429 struct nfc_digital_dev
*ddev
;
433 struct sk_buff
*tx_skb
;
434 struct sk_buff
*rx_skb
;
435 nfc_digital_cmd_complete_t cb
;
440 u8 modulator_sys_clk_ctrl
;
443 unsigned int guard_time
;
449 struct gpio_desc
*en_gpiod
;
450 struct gpio_desc
*en2_gpiod
;
452 unsigned int timeout
;
454 struct delayed_work timeout_work
;
457 static int trf7970a_cmd(struct trf7970a
*trf
, u8 opcode
)
459 u8 cmd
= TRF7970A_CMD_BIT_CTRL
| TRF7970A_CMD_BIT_OPCODE(opcode
);
462 dev_dbg(trf
->dev
, "cmd: 0x%x\n", cmd
);
464 ret
= spi_write(trf
->spi
, &cmd
, 1);
466 dev_err(trf
->dev
, "%s - cmd: 0x%x, ret: %d\n", __func__
, cmd
,
471 static int trf7970a_read(struct trf7970a
*trf
, u8 reg
, u8
*val
)
473 u8 addr
= TRF7970A_CMD_BIT_RW
| reg
;
476 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, val
, 1);
478 dev_err(trf
->dev
, "%s - addr: 0x%x, ret: %d\n", __func__
, addr
,
481 dev_dbg(trf
->dev
, "read(0x%x): 0x%x\n", addr
, *val
);
486 static int trf7970a_read_cont(struct trf7970a
*trf
, u8 reg
, u8
*buf
,
489 u8 addr
= reg
| TRF7970A_CMD_BIT_RW
| TRF7970A_CMD_BIT_CONTINUOUS
;
490 struct spi_transfer t
[2];
491 struct spi_message m
;
494 dev_dbg(trf
->dev
, "read_cont(0x%x, %zd)\n", addr
, len
);
496 spi_message_init(&m
);
498 memset(&t
, 0, sizeof(t
));
501 t
[0].len
= sizeof(addr
);
502 spi_message_add_tail(&t
[0], &m
);
506 spi_message_add_tail(&t
[1], &m
);
508 ret
= spi_sync(trf
->spi
, &m
);
510 dev_err(trf
->dev
, "%s - addr: 0x%x, ret: %d\n", __func__
, addr
,
515 static int trf7970a_write(struct trf7970a
*trf
, u8 reg
, u8 val
)
517 u8 buf
[2] = { reg
, val
};
520 dev_dbg(trf
->dev
, "write(0x%x): 0x%x\n", reg
, val
);
522 ret
= spi_write(trf
->spi
, buf
, 2);
524 dev_err(trf
->dev
, "%s - write: 0x%x 0x%x, ret: %d\n", __func__
,
525 buf
[0], buf
[1], ret
);
530 static int trf7970a_read_irqstatus(struct trf7970a
*trf
, u8
*status
)
536 addr
= TRF7970A_IRQ_STATUS
| TRF7970A_CMD_BIT_RW
;
538 if (trf
->quirks
& TRF7970A_QUIRK_IRQ_STATUS_READ
) {
539 addr
|= TRF7970A_CMD_BIT_CONTINUOUS
;
540 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, buf
, 2);
542 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, buf
, 1);
546 dev_err(trf
->dev
, "%s - irqstatus: Status read failed: %d\n",
554 static int trf7970a_read_target_proto(struct trf7970a
*trf
, u8
*target_proto
)
560 addr
= TRF79070A_NFC_TARGET_PROTOCOL
| TRF7970A_CMD_BIT_RW
|
561 TRF7970A_CMD_BIT_CONTINUOUS
;
563 ret
= spi_write_then_read(trf
->spi
, &addr
, 1, buf
, 2);
565 dev_err(trf
->dev
, "%s - target_proto: Read failed: %d\n",
568 *target_proto
= buf
[0];
573 static int trf7970a_mode_detect(struct trf7970a
*trf
, u8
*rf_tech
)
576 u8 target_proto
, tech
;
578 ret
= trf7970a_read_target_proto(trf
, &target_proto
);
582 switch (target_proto
) {
583 case TRF79070A_NFC_TARGET_PROTOCOL_106A
:
584 tech
= NFC_DIGITAL_RF_TECH_106A
;
586 case TRF79070A_NFC_TARGET_PROTOCOL_106B
:
587 tech
= NFC_DIGITAL_RF_TECH_106B
;
589 case TRF79070A_NFC_TARGET_PROTOCOL_212F
:
590 tech
= NFC_DIGITAL_RF_TECH_212F
;
592 case TRF79070A_NFC_TARGET_PROTOCOL_424F
:
593 tech
= NFC_DIGITAL_RF_TECH_424F
;
596 dev_dbg(trf
->dev
, "%s - mode_detect: target_proto: 0x%x\n",
597 __func__
, target_proto
);
606 static void trf7970a_send_upstream(struct trf7970a
*trf
)
608 dev_kfree_skb_any(trf
->tx_skb
);
611 if (trf
->rx_skb
&& !IS_ERR(trf
->rx_skb
) && !trf
->aborting
)
612 print_hex_dump_debug("trf7970a rx data: ", DUMP_PREFIX_NONE
,
613 16, 1, trf
->rx_skb
->data
, trf
->rx_skb
->len
,
616 trf
->state
= TRF7970A_ST_IDLE
;
619 dev_dbg(trf
->dev
, "Abort process complete\n");
621 if (!IS_ERR(trf
->rx_skb
)) {
622 kfree_skb(trf
->rx_skb
);
623 trf
->rx_skb
= ERR_PTR(-ECANCELED
);
626 trf
->aborting
= false;
629 trf
->cb(trf
->ddev
, trf
->cb_arg
, trf
->rx_skb
);
634 static void trf7970a_send_err_upstream(struct trf7970a
*trf
, int errno
)
636 dev_dbg(trf
->dev
, "Error - state: %d, errno: %d\n", trf
->state
, errno
);
638 cancel_delayed_work(&trf
->timeout_work
);
640 kfree_skb(trf
->rx_skb
);
641 trf
->rx_skb
= ERR_PTR(errno
);
643 trf7970a_send_upstream(trf
);
646 static int trf7970a_transmit(struct trf7970a
*trf
, struct sk_buff
*skb
,
647 unsigned int len
, const u8
*prefix
,
648 unsigned int prefix_len
)
650 struct spi_transfer t
[2];
651 struct spi_message m
;
652 unsigned int timeout
;
655 print_hex_dump_debug("trf7970a tx data: ", DUMP_PREFIX_NONE
,
656 16, 1, skb
->data
, len
, false);
658 spi_message_init(&m
);
660 memset(&t
, 0, sizeof(t
));
662 t
[0].tx_buf
= prefix
;
663 t
[0].len
= prefix_len
;
664 spi_message_add_tail(&t
[0], &m
);
666 t
[1].tx_buf
= skb
->data
;
668 spi_message_add_tail(&t
[1], &m
);
670 ret
= spi_sync(trf
->spi
, &m
);
672 dev_err(trf
->dev
, "%s - Can't send tx data: %d\n", __func__
,
680 trf
->state
= TRF7970A_ST_WAIT_FOR_TX_FIFO
;
681 timeout
= TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT
;
683 if (trf
->issue_eof
) {
684 trf
->state
= TRF7970A_ST_WAIT_TO_ISSUE_EOF
;
685 timeout
= TRF7970A_WAIT_TO_ISSUE_ISO15693_EOF
;
687 trf
->state
= TRF7970A_ST_WAIT_FOR_RX_DATA
;
690 timeout
= TRF7970A_WAIT_FOR_TX_IRQ
;
692 timeout
= trf
->timeout
;
696 dev_dbg(trf
->dev
, "Setting timeout for %d ms, state: %d\n", timeout
,
699 schedule_delayed_work(&trf
->timeout_work
, msecs_to_jiffies(timeout
));
704 static void trf7970a_fill_fifo(struct trf7970a
*trf
)
706 struct sk_buff
*skb
= trf
->tx_skb
;
712 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
, &fifo_bytes
);
714 trf7970a_send_err_upstream(trf
, ret
);
718 dev_dbg(trf
->dev
, "Filling FIFO - fifo_bytes: 0x%x\n", fifo_bytes
);
720 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
722 /* Calculate how much more data can be written to the fifo */
723 len
= TRF7970A_FIFO_SIZE
- fifo_bytes
;
725 schedule_delayed_work(&trf
->timeout_work
,
726 msecs_to_jiffies(TRF7970A_WAIT_FOR_FIFO_DRAIN_TIMEOUT
));
730 len
= min(skb
->len
, len
);
732 prefix
= TRF7970A_CMD_BIT_CONTINUOUS
| TRF7970A_FIFO_IO_REGISTER
;
734 ret
= trf7970a_transmit(trf
, skb
, len
, &prefix
, sizeof(prefix
));
736 trf7970a_send_err_upstream(trf
, ret
);
739 static void trf7970a_drain_fifo(struct trf7970a
*trf
, u8 status
)
741 struct sk_buff
*skb
= trf
->rx_skb
;
745 if (status
& TRF7970A_IRQ_STATUS_ERROR
) {
746 trf7970a_send_err_upstream(trf
, -EIO
);
750 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
, &fifo_bytes
);
752 trf7970a_send_err_upstream(trf
, ret
);
756 dev_dbg(trf
->dev
, "Draining FIFO - fifo_bytes: 0x%x\n", fifo_bytes
);
758 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
763 if (fifo_bytes
> skb_tailroom(skb
)) {
764 skb
= skb_copy_expand(skb
, skb_headroom(skb
),
765 max_t(int, fifo_bytes
,
766 TRF7970A_RX_SKB_ALLOC_SIZE
),
769 trf7970a_send_err_upstream(trf
, -ENOMEM
);
773 kfree_skb(trf
->rx_skb
);
777 ret
= trf7970a_read_cont(trf
, TRF7970A_FIFO_IO_REGISTER
,
778 skb_put(skb
, fifo_bytes
), fifo_bytes
);
780 trf7970a_send_err_upstream(trf
, ret
);
784 /* If received Type 2 ACK/NACK, shift right 4 bits and pass up */
785 if ((trf
->framing
== NFC_DIGITAL_FRAMING_NFCA_T2T
) && (skb
->len
== 1) &&
786 (trf
->special_fcn_reg1
== TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX
)) {
788 status
= TRF7970A_IRQ_STATUS_SRX
;
790 trf
->state
= TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
;
792 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
, &fifo_bytes
);
794 trf7970a_send_err_upstream(trf
, ret
);
798 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
800 /* If there are bytes in the FIFO, set status to '0' so
801 * the if stmt below doesn't fire and the driver will wait
802 * for the trf7970a to generate another RX interrupt.
809 if (status
== TRF7970A_IRQ_STATUS_SRX
) { /* Receive complete */
810 trf7970a_send_upstream(trf
);
814 dev_dbg(trf
->dev
, "Setting timeout for %d ms\n",
815 TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT
);
817 schedule_delayed_work(&trf
->timeout_work
,
818 msecs_to_jiffies(TRF7970A_WAIT_FOR_RX_DATA_TIMEOUT
));
821 static irqreturn_t
trf7970a_irq(int irq
, void *dev_id
)
823 struct trf7970a
*trf
= dev_id
;
825 u8 status
, fifo_bytes
, iso_ctrl
;
827 mutex_lock(&trf
->lock
);
829 if (trf
->state
== TRF7970A_ST_RF_OFF
) {
830 mutex_unlock(&trf
->lock
);
834 ret
= trf7970a_read_irqstatus(trf
, &status
);
836 mutex_unlock(&trf
->lock
);
840 dev_dbg(trf
->dev
, "IRQ - state: %d, status: 0x%x\n", trf
->state
,
844 mutex_unlock(&trf
->lock
);
848 switch (trf
->state
) {
849 case TRF7970A_ST_IDLE
:
850 case TRF7970A_ST_IDLE_RX_BLOCKED
:
851 /* If initiator and getting interrupts caused by RF noise,
852 * turn off the receiver to avoid unnecessary interrupts.
853 * It will be turned back on in trf7970a_send_cmd() when
854 * the next command is issued.
856 if (trf
->is_initiator
&& (status
& TRF7970A_IRQ_STATUS_ERROR
)) {
857 trf7970a_cmd(trf
, TRF7970A_CMD_BLOCK_RX
);
858 trf
->state
= TRF7970A_ST_IDLE_RX_BLOCKED
;
861 trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
863 case TRF7970A_ST_WAIT_FOR_TX_FIFO
:
864 if (status
& TRF7970A_IRQ_STATUS_TX
) {
865 trf
->ignore_timeout
=
866 !cancel_delayed_work(&trf
->timeout_work
);
867 trf7970a_fill_fifo(trf
);
869 trf7970a_send_err_upstream(trf
, -EIO
);
872 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
873 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
874 if (status
& TRF7970A_IRQ_STATUS_SRX
) {
875 trf
->ignore_timeout
=
876 !cancel_delayed_work(&trf
->timeout_work
);
877 trf7970a_drain_fifo(trf
, status
);
878 } else if (status
& TRF7970A_IRQ_STATUS_FIFO
) {
879 ret
= trf7970a_read(trf
, TRF7970A_FIFO_STATUS
,
882 fifo_bytes
&= ~TRF7970A_FIFO_STATUS_OVERFLOW
;
885 trf7970a_send_err_upstream(trf
, ret
);
886 else if (!fifo_bytes
)
887 trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
888 } else if ((status
== TRF7970A_IRQ_STATUS_TX
) ||
889 (!trf
->is_initiator
&&
890 (status
== (TRF7970A_IRQ_STATUS_TX
|
891 TRF7970A_IRQ_STATUS_NFC_RF
)))) {
892 trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
895 trf
->ignore_timeout
=
896 !cancel_delayed_work(&trf
->timeout_work
);
897 trf
->rx_skb
= ERR_PTR(0);
898 trf7970a_send_upstream(trf
);
902 if (trf
->is_initiator
)
905 iso_ctrl
= trf
->iso_ctrl
;
907 switch (trf
->framing
) {
908 case NFC_DIGITAL_FRAMING_NFCA_STANDARD
:
909 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT_NO_CRC
;
910 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
911 trf
->iso_ctrl
= 0xff; /* Force ISO_CTRL write */
913 case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A
:
914 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
915 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
916 trf
->iso_ctrl
= 0xff; /* Force ISO_CTRL write */
918 case NFC_DIGITAL_FRAMING_NFCA_ANTICOL_COMPLETE
:
919 ret
= trf7970a_write(trf
,
920 TRF7970A_SPECIAL_FCN_REG1
,
921 TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL
);
923 goto err_unlock_exit
;
925 trf
->special_fcn_reg1
=
926 TRF7970A_SPECIAL_FCN_REG1_14_ANTICOLL
;
932 if (iso_ctrl
!= trf
->iso_ctrl
) {
933 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
,
936 goto err_unlock_exit
;
938 trf
->iso_ctrl
= iso_ctrl
;
941 trf7970a_send_err_upstream(trf
, -EIO
);
944 case TRF7970A_ST_WAIT_TO_ISSUE_EOF
:
945 if (status
!= TRF7970A_IRQ_STATUS_TX
)
946 trf7970a_send_err_upstream(trf
, -EIO
);
948 case TRF7970A_ST_LISTENING
:
949 if (status
& TRF7970A_IRQ_STATUS_SRX
) {
950 trf
->ignore_timeout
=
951 !cancel_delayed_work(&trf
->timeout_work
);
952 trf7970a_drain_fifo(trf
, status
);
953 } else if (!(status
& TRF7970A_IRQ_STATUS_NFC_RF
)) {
954 trf7970a_send_err_upstream(trf
, -EIO
);
957 case TRF7970A_ST_LISTENING_MD
:
958 if (status
& TRF7970A_IRQ_STATUS_SRX
) {
959 trf
->ignore_timeout
=
960 !cancel_delayed_work(&trf
->timeout_work
);
962 ret
= trf7970a_mode_detect(trf
, &trf
->md_rf_tech
);
964 trf7970a_send_err_upstream(trf
, ret
);
966 trf
->state
= TRF7970A_ST_LISTENING
;
967 trf7970a_drain_fifo(trf
, status
);
969 } else if (!(status
& TRF7970A_IRQ_STATUS_NFC_RF
)) {
970 trf7970a_send_err_upstream(trf
, -EIO
);
974 dev_err(trf
->dev
, "%s - Driver in invalid state: %d\n",
975 __func__
, trf
->state
);
979 mutex_unlock(&trf
->lock
);
983 static void trf7970a_issue_eof(struct trf7970a
*trf
)
987 dev_dbg(trf
->dev
, "Issuing EOF\n");
989 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_FIFO_RESET
);
991 trf7970a_send_err_upstream(trf
, ret
);
993 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_EOF
);
995 trf7970a_send_err_upstream(trf
, ret
);
997 trf
->state
= TRF7970A_ST_WAIT_FOR_RX_DATA
;
999 dev_dbg(trf
->dev
, "Setting timeout for %d ms, state: %d\n",
1000 trf
->timeout
, trf
->state
);
1002 schedule_delayed_work(&trf
->timeout_work
,
1003 msecs_to_jiffies(trf
->timeout
));
1006 static void trf7970a_timeout_work_handler(struct work_struct
*work
)
1008 struct trf7970a
*trf
= container_of(work
, struct trf7970a
,
1011 dev_dbg(trf
->dev
, "Timeout - state: %d, ignore_timeout: %d\n",
1012 trf
->state
, trf
->ignore_timeout
);
1014 mutex_lock(&trf
->lock
);
1016 if (trf
->ignore_timeout
)
1017 trf
->ignore_timeout
= false;
1018 else if (trf
->state
== TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
)
1019 trf7970a_drain_fifo(trf
, TRF7970A_IRQ_STATUS_SRX
);
1020 else if (trf
->state
== TRF7970A_ST_WAIT_TO_ISSUE_EOF
)
1021 trf7970a_issue_eof(trf
);
1023 trf7970a_send_err_upstream(trf
, -ETIMEDOUT
);
1025 mutex_unlock(&trf
->lock
);
1028 static int trf7970a_init(struct trf7970a
*trf
)
1032 dev_dbg(trf
->dev
, "Initializing device - state: %d\n", trf
->state
);
1034 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_SOFT_INIT
);
1038 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_IDLE
);
1042 ret
= trf7970a_write(trf
, TRF7970A_REG_IO_CTRL
,
1043 trf
->io_ctrl
| TRF7970A_REG_IO_CTRL_VRS(0x1));
1047 ret
= trf7970a_write(trf
, TRF7970A_NFC_TARGET_LEVEL
, 0);
1051 usleep_range(1000, 2000);
1053 trf
->chip_status_ctrl
&= ~TRF7970A_CHIP_STATUS_RF_ON
;
1055 ret
= trf7970a_write(trf
, TRF7970A_MODULATOR_SYS_CLK_CTRL
,
1056 trf
->modulator_sys_clk_ctrl
);
1060 ret
= trf7970a_write(trf
, TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS
,
1061 TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLH_96
|
1062 TRF7970A_ADJUTABLE_FIFO_IRQ_LEVELS_WLL_32
);
1066 ret
= trf7970a_write(trf
, TRF7970A_SPECIAL_FCN_REG1
, 0);
1070 trf
->special_fcn_reg1
= 0;
1072 trf
->iso_ctrl
= 0xff;
1076 dev_dbg(trf
->dev
, "Couldn't init device: %d\n", ret
);
1080 static void trf7970a_switch_rf_off(struct trf7970a
*trf
)
1082 if ((trf
->state
== TRF7970A_ST_PWR_OFF
) ||
1083 (trf
->state
== TRF7970A_ST_RF_OFF
))
1086 dev_dbg(trf
->dev
, "Switching rf off\n");
1088 trf
->chip_status_ctrl
&= ~TRF7970A_CHIP_STATUS_RF_ON
;
1090 trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
, trf
->chip_status_ctrl
);
1092 trf
->aborting
= false;
1093 trf
->state
= TRF7970A_ST_RF_OFF
;
1095 pm_runtime_mark_last_busy(trf
->dev
);
1096 pm_runtime_put_autosuspend(trf
->dev
);
1099 static int trf7970a_switch_rf_on(struct trf7970a
*trf
)
1103 dev_dbg(trf
->dev
, "Switching rf on\n");
1105 pm_runtime_get_sync(trf
->dev
);
1107 if (trf
->state
!= TRF7970A_ST_RF_OFF
) { /* Power on, RF off */
1108 dev_err(trf
->dev
, "%s - Incorrect state: %d\n", __func__
,
1113 ret
= trf7970a_init(trf
);
1115 dev_err(trf
->dev
, "%s - Can't initialize: %d\n", __func__
, ret
);
1119 trf
->state
= TRF7970A_ST_IDLE
;
1124 static int trf7970a_switch_rf(struct nfc_digital_dev
*ddev
, bool on
)
1126 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1129 dev_dbg(trf
->dev
, "Switching RF - state: %d, on: %d\n", trf
->state
, on
);
1131 mutex_lock(&trf
->lock
);
1134 switch (trf
->state
) {
1135 case TRF7970A_ST_PWR_OFF
:
1136 case TRF7970A_ST_RF_OFF
:
1137 ret
= trf7970a_switch_rf_on(trf
);
1139 case TRF7970A_ST_IDLE
:
1140 case TRF7970A_ST_IDLE_RX_BLOCKED
:
1143 dev_err(trf
->dev
, "%s - Invalid request: %d %d\n",
1144 __func__
, trf
->state
, on
);
1145 trf7970a_switch_rf_off(trf
);
1149 switch (trf
->state
) {
1150 case TRF7970A_ST_PWR_OFF
:
1151 case TRF7970A_ST_RF_OFF
:
1154 dev_err(trf
->dev
, "%s - Invalid request: %d %d\n",
1155 __func__
, trf
->state
, on
);
1158 case TRF7970A_ST_IDLE
:
1159 case TRF7970A_ST_IDLE_RX_BLOCKED
:
1160 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
1161 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
1162 trf7970a_switch_rf_off(trf
);
1166 mutex_unlock(&trf
->lock
);
1170 static int trf7970a_in_config_rf_tech(struct trf7970a
*trf
, int tech
)
1174 dev_dbg(trf
->dev
, "rf technology: %d\n", tech
);
1177 case NFC_DIGITAL_RF_TECH_106A
:
1178 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_14443A_106
;
1179 trf
->modulator_sys_clk_ctrl
=
1180 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1181 TRF7970A_MODULATOR_DEPTH_OOK
;
1182 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCA
;
1184 case NFC_DIGITAL_RF_TECH_106B
:
1185 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_14443B_106
;
1186 trf
->modulator_sys_clk_ctrl
=
1187 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1188 TRF7970A_MODULATOR_DEPTH_ASK10
;
1189 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCB
;
1191 case NFC_DIGITAL_RF_TECH_212F
:
1192 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_FELICA_212
;
1193 trf
->modulator_sys_clk_ctrl
=
1194 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1195 TRF7970A_MODULATOR_DEPTH_ASK10
;
1196 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCF
;
1198 case NFC_DIGITAL_RF_TECH_424F
:
1199 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_FELICA_424
;
1200 trf
->modulator_sys_clk_ctrl
=
1201 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1202 TRF7970A_MODULATOR_DEPTH_ASK10
;
1203 trf
->guard_time
= TRF7970A_GUARD_TIME_NFCF
;
1205 case NFC_DIGITAL_RF_TECH_ISO15693
:
1206 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648
;
1207 trf
->modulator_sys_clk_ctrl
=
1208 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1209 TRF7970A_MODULATOR_DEPTH_OOK
;
1210 trf
->guard_time
= TRF7970A_GUARD_TIME_15693
;
1213 dev_dbg(trf
->dev
, "Unsupported rf technology: %d\n", tech
);
1217 trf
->technology
= tech
;
1219 /* If in initiator mode and not changing the RF tech due to a
1220 * PSL sequence (indicated by 'trf->iso_ctrl == 0xff' from
1221 * trf7970a_init()), clear the NFC Target Detection Level register
1224 if (trf
->iso_ctrl
== 0xff)
1225 ret
= trf7970a_write(trf
, TRF7970A_NFC_TARGET_LEVEL
, 0);
1230 static int trf7970a_is_rf_field(struct trf7970a
*trf
, bool *is_rf_field
)
1235 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1236 trf
->chip_status_ctrl
|
1237 TRF7970A_CHIP_STATUS_REC_ON
);
1241 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_TEST_EXT_RF
);
1245 usleep_range(50, 60);
1247 ret
= trf7970a_read(trf
, TRF7970A_RSSI_OSC_STATUS
, &rssi
);
1251 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1252 trf
->chip_status_ctrl
);
1256 if (rssi
& TRF7970A_RSSI_OSC_STATUS_RSSI_MASK
)
1257 *is_rf_field
= true;
1259 *is_rf_field
= false;
1264 static int trf7970a_in_config_framing(struct trf7970a
*trf
, int framing
)
1266 u8 iso_ctrl
= trf
->iso_ctrl_tech
;
1267 bool is_rf_field
= false;
1270 dev_dbg(trf
->dev
, "framing: %d\n", framing
);
1273 case NFC_DIGITAL_FRAMING_NFCA_SHORT
:
1274 case NFC_DIGITAL_FRAMING_NFCA_STANDARD
:
1275 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT_NO_CRC
;
1276 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
1278 case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A
:
1279 case NFC_DIGITAL_FRAMING_NFCA_T4T
:
1280 case NFC_DIGITAL_FRAMING_NFCB
:
1281 case NFC_DIGITAL_FRAMING_NFCB_T4T
:
1282 case NFC_DIGITAL_FRAMING_NFCF
:
1283 case NFC_DIGITAL_FRAMING_NFCF_T3T
:
1284 case NFC_DIGITAL_FRAMING_ISO15693_INVENTORY
:
1285 case NFC_DIGITAL_FRAMING_ISO15693_T5T
:
1286 case NFC_DIGITAL_FRAMING_NFCA_NFC_DEP
:
1287 case NFC_DIGITAL_FRAMING_NFCF_NFC_DEP
:
1288 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1289 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
1291 case NFC_DIGITAL_FRAMING_NFCA_T2T
:
1292 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1293 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
1296 dev_dbg(trf
->dev
, "Unsupported Framing: %d\n", framing
);
1300 trf
->framing
= framing
;
1302 if (!(trf
->chip_status_ctrl
& TRF7970A_CHIP_STATUS_RF_ON
)) {
1303 ret
= trf7970a_is_rf_field(trf
, &is_rf_field
);
1311 if (iso_ctrl
!= trf
->iso_ctrl
) {
1312 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
, iso_ctrl
);
1316 trf
->iso_ctrl
= iso_ctrl
;
1318 ret
= trf7970a_write(trf
, TRF7970A_MODULATOR_SYS_CLK_CTRL
,
1319 trf
->modulator_sys_clk_ctrl
);
1324 if (!(trf
->chip_status_ctrl
& TRF7970A_CHIP_STATUS_RF_ON
)) {
1325 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1326 trf
->chip_status_ctrl
|
1327 TRF7970A_CHIP_STATUS_RF_ON
);
1331 trf
->chip_status_ctrl
|= TRF7970A_CHIP_STATUS_RF_ON
;
1333 usleep_range(trf
->guard_time
, trf
->guard_time
+ 1000);
1339 static int trf7970a_in_configure_hw(struct nfc_digital_dev
*ddev
, int type
,
1342 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1345 dev_dbg(trf
->dev
, "Configure hw - type: %d, param: %d\n", type
, param
);
1347 mutex_lock(&trf
->lock
);
1349 trf
->is_initiator
= true;
1351 if ((trf
->state
== TRF7970A_ST_PWR_OFF
) ||
1352 (trf
->state
== TRF7970A_ST_RF_OFF
)) {
1353 ret
= trf7970a_switch_rf_on(trf
);
1359 case NFC_DIGITAL_CONFIG_RF_TECH
:
1360 ret
= trf7970a_in_config_rf_tech(trf
, param
);
1362 case NFC_DIGITAL_CONFIG_FRAMING
:
1363 ret
= trf7970a_in_config_framing(trf
, param
);
1366 dev_dbg(trf
->dev
, "Unknown type: %d\n", type
);
1371 mutex_unlock(&trf
->lock
);
1375 static int trf7970a_is_iso15693_write_or_lock(u8 cmd
)
1378 case ISO15693_CMD_WRITE_SINGLE_BLOCK
:
1379 case ISO15693_CMD_LOCK_BLOCK
:
1380 case ISO15693_CMD_WRITE_MULTIPLE_BLOCK
:
1381 case ISO15693_CMD_WRITE_AFI
:
1382 case ISO15693_CMD_LOCK_AFI
:
1383 case ISO15693_CMD_WRITE_DSFID
:
1384 case ISO15693_CMD_LOCK_DSFID
:
1391 static int trf7970a_per_cmd_config(struct trf7970a
*trf
,
1392 const struct sk_buff
*skb
)
1394 const u8
*req
= skb
->data
;
1395 u8 special_fcn_reg1
, iso_ctrl
;
1398 trf
->issue_eof
= false;
1400 /* When issuing Type 2 read command, make sure the '4_bit_RX' bit in
1401 * special functions register 1 is cleared; otherwise, its a write or
1402 * sector select command and '4_bit_RX' must be set.
1404 * When issuing an ISO 15693 command, inspect the flags byte to see
1405 * what speed to use. Also, remember if the OPTION flag is set on
1406 * a Type 5 write or lock command so the driver will know that it
1407 * has to send an EOF in order to get a response.
1409 if ((trf
->technology
== NFC_DIGITAL_RF_TECH_106A
) &&
1410 (trf
->framing
== NFC_DIGITAL_FRAMING_NFCA_T2T
)) {
1411 if (req
[0] == NFC_T2T_CMD_READ
)
1412 special_fcn_reg1
= 0;
1414 special_fcn_reg1
= TRF7970A_SPECIAL_FCN_REG1_4_BIT_RX
;
1416 if (special_fcn_reg1
!= trf
->special_fcn_reg1
) {
1417 ret
= trf7970a_write(trf
, TRF7970A_SPECIAL_FCN_REG1
,
1422 trf
->special_fcn_reg1
= special_fcn_reg1
;
1424 } else if (trf
->technology
== NFC_DIGITAL_RF_TECH_ISO15693
) {
1425 iso_ctrl
= trf
->iso_ctrl
& ~TRF7970A_ISO_CTRL_RFID_SPEED_MASK
;
1427 switch (req
[0] & ISO15693_REQ_FLAG_SPEED_MASK
) {
1429 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_SGL_1OF4_662
;
1431 case ISO15693_REQ_FLAG_SUB_CARRIER
:
1432 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_DBL_1OF4_667a
;
1434 case ISO15693_REQ_FLAG_DATA_RATE
:
1435 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_SGL_1OF4_2648
;
1437 case (ISO15693_REQ_FLAG_SUB_CARRIER
|
1438 ISO15693_REQ_FLAG_DATA_RATE
):
1439 iso_ctrl
|= TRF7970A_ISO_CTRL_15693_DBL_1OF4_2669
;
1443 if (iso_ctrl
!= trf
->iso_ctrl
) {
1444 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
, iso_ctrl
);
1448 trf
->iso_ctrl
= iso_ctrl
;
1451 if ((trf
->framing
== NFC_DIGITAL_FRAMING_ISO15693_T5T
) &&
1452 trf7970a_is_iso15693_write_or_lock(req
[1]) &&
1453 (req
[0] & ISO15693_REQ_FLAG_OPTION
))
1454 trf
->issue_eof
= true;
1460 static int trf7970a_send_cmd(struct nfc_digital_dev
*ddev
,
1461 struct sk_buff
*skb
, u16 timeout
,
1462 nfc_digital_cmd_complete_t cb
, void *arg
)
1464 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1470 dev_dbg(trf
->dev
, "New request - state: %d, timeout: %d ms, len: %d\n",
1471 trf
->state
, timeout
, skb
->len
);
1473 if (skb
->len
> TRF7970A_TX_MAX
)
1476 mutex_lock(&trf
->lock
);
1478 if ((trf
->state
!= TRF7970A_ST_IDLE
) &&
1479 (trf
->state
!= TRF7970A_ST_IDLE_RX_BLOCKED
)) {
1480 dev_err(trf
->dev
, "%s - Bogus state: %d\n", __func__
,
1486 if (trf
->aborting
) {
1487 dev_dbg(trf
->dev
, "Abort process complete\n");
1488 trf
->aborting
= false;
1494 trf
->rx_skb
= nfc_alloc_recv_skb(TRF7970A_RX_SKB_ALLOC_SIZE
,
1497 dev_dbg(trf
->dev
, "Can't alloc rx_skb\n");
1503 if (trf
->state
== TRF7970A_ST_IDLE_RX_BLOCKED
) {
1504 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_ENABLE_RX
);
1508 trf
->state
= TRF7970A_ST_IDLE
;
1511 if (trf
->is_initiator
) {
1512 ret
= trf7970a_per_cmd_config(trf
, skb
);
1521 trf
->timeout
= timeout
;
1522 trf
->ignore_timeout
= false;
1526 /* TX data must be prefixed with a FIFO reset cmd, a cmd that depends
1527 * on what the current framing is, the address of the TX length byte 1
1528 * register (0x1d), and the 2 byte length of the data to be transmitted.
1529 * That totals 5 bytes.
1531 prefix
[0] = TRF7970A_CMD_BIT_CTRL
|
1532 TRF7970A_CMD_BIT_OPCODE(TRF7970A_CMD_FIFO_RESET
);
1533 prefix
[1] = TRF7970A_CMD_BIT_CTRL
|
1534 TRF7970A_CMD_BIT_OPCODE(trf
->tx_cmd
);
1535 prefix
[2] = TRF7970A_CMD_BIT_CONTINUOUS
| TRF7970A_TX_LENGTH_BYTE1
;
1537 if (trf
->framing
== NFC_DIGITAL_FRAMING_NFCA_SHORT
) {
1539 prefix
[4] = 0x0f; /* 7 bits */
1541 prefix
[3] = (len
& 0xf00) >> 4;
1542 prefix
[3] |= ((len
& 0xf0) >> 4);
1543 prefix
[4] = ((len
& 0x0f) << 4);
1546 len
= min_t(int, skb
->len
, TRF7970A_FIFO_SIZE
);
1548 /* Clear possible spurious interrupt */
1549 ret
= trf7970a_read_irqstatus(trf
, &status
);
1553 ret
= trf7970a_transmit(trf
, skb
, len
, prefix
, sizeof(prefix
));
1555 kfree_skb(trf
->rx_skb
);
1560 mutex_unlock(&trf
->lock
);
1564 static int trf7970a_tg_config_rf_tech(struct trf7970a
*trf
, int tech
)
1568 dev_dbg(trf
->dev
, "rf technology: %d\n", tech
);
1571 case NFC_DIGITAL_RF_TECH_106A
:
1572 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE
|
1573 TRF7970A_ISO_CTRL_NFC_CE
| TRF7970A_ISO_CTRL_NFC_CE_14443A
;
1574 trf
->modulator_sys_clk_ctrl
=
1575 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1576 TRF7970A_MODULATOR_DEPTH_OOK
;
1578 case NFC_DIGITAL_RF_TECH_212F
:
1579 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE
|
1580 TRF7970A_ISO_CTRL_NFC_NFCF_212
;
1581 trf
->modulator_sys_clk_ctrl
=
1582 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1583 TRF7970A_MODULATOR_DEPTH_ASK10
;
1585 case NFC_DIGITAL_RF_TECH_424F
:
1586 trf
->iso_ctrl_tech
= TRF7970A_ISO_CTRL_NFC_NFC_CE_MODE
|
1587 TRF7970A_ISO_CTRL_NFC_NFCF_424
;
1588 trf
->modulator_sys_clk_ctrl
=
1589 (trf
->modulator_sys_clk_ctrl
& 0xf8) |
1590 TRF7970A_MODULATOR_DEPTH_ASK10
;
1593 dev_dbg(trf
->dev
, "Unsupported rf technology: %d\n", tech
);
1597 trf
->technology
= tech
;
1599 /* Normally we write the ISO_CTRL register in
1600 * trf7970a_tg_config_framing() because the framing can change
1601 * the value written. However, when sending a PSL RES,
1602 * digital_tg_send_psl_res_complete() doesn't call
1603 * trf7970a_tg_config_framing() so we must write the register
1606 if ((trf
->framing
== NFC_DIGITAL_FRAMING_NFC_DEP_ACTIVATED
) &&
1607 (trf
->iso_ctrl_tech
!= trf
->iso_ctrl
)) {
1608 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
,
1609 trf
->iso_ctrl_tech
);
1611 trf
->iso_ctrl
= trf
->iso_ctrl_tech
;
1617 /* Since this is a target routine, several of the framing calls are
1618 * made between receiving the request and sending the response so they
1619 * should take effect until after the response is sent. This is accomplished
1620 * by skipping the ISO_CTRL register write here and doing it in the interrupt
1623 static int trf7970a_tg_config_framing(struct trf7970a
*trf
, int framing
)
1625 u8 iso_ctrl
= trf
->iso_ctrl_tech
;
1628 dev_dbg(trf
->dev
, "framing: %d\n", framing
);
1631 case NFC_DIGITAL_FRAMING_NFCA_NFC_DEP
:
1632 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT_NO_CRC
;
1633 iso_ctrl
|= TRF7970A_ISO_CTRL_RX_CRC_N
;
1635 case NFC_DIGITAL_FRAMING_NFCA_STANDARD
:
1636 case NFC_DIGITAL_FRAMING_NFCA_STANDARD_WITH_CRC_A
:
1637 case NFC_DIGITAL_FRAMING_NFCA_ANTICOL_COMPLETE
:
1638 /* These ones are applied in the interrupt handler */
1639 iso_ctrl
= trf
->iso_ctrl
; /* Don't write to ISO_CTRL yet */
1641 case NFC_DIGITAL_FRAMING_NFCF_NFC_DEP
:
1642 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1643 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
1645 case NFC_DIGITAL_FRAMING_NFC_DEP_ACTIVATED
:
1646 trf
->tx_cmd
= TRF7970A_CMD_TRANSMIT
;
1647 iso_ctrl
&= ~TRF7970A_ISO_CTRL_RX_CRC_N
;
1650 dev_dbg(trf
->dev
, "Unsupported Framing: %d\n", framing
);
1654 trf
->framing
= framing
;
1656 if (iso_ctrl
!= trf
->iso_ctrl
) {
1657 ret
= trf7970a_write(trf
, TRF7970A_ISO_CTRL
, iso_ctrl
);
1661 trf
->iso_ctrl
= iso_ctrl
;
1663 ret
= trf7970a_write(trf
, TRF7970A_MODULATOR_SYS_CLK_CTRL
,
1664 trf
->modulator_sys_clk_ctrl
);
1669 if (!(trf
->chip_status_ctrl
& TRF7970A_CHIP_STATUS_RF_ON
)) {
1670 ret
= trf7970a_write(trf
, TRF7970A_CHIP_STATUS_CTRL
,
1671 trf
->chip_status_ctrl
|
1672 TRF7970A_CHIP_STATUS_RF_ON
);
1676 trf
->chip_status_ctrl
|= TRF7970A_CHIP_STATUS_RF_ON
;
1682 static int trf7970a_tg_configure_hw(struct nfc_digital_dev
*ddev
, int type
,
1685 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1688 dev_dbg(trf
->dev
, "Configure hw - type: %d, param: %d\n", type
, param
);
1690 mutex_lock(&trf
->lock
);
1692 trf
->is_initiator
= false;
1694 if ((trf
->state
== TRF7970A_ST_PWR_OFF
) ||
1695 (trf
->state
== TRF7970A_ST_RF_OFF
)) {
1696 ret
= trf7970a_switch_rf_on(trf
);
1702 case NFC_DIGITAL_CONFIG_RF_TECH
:
1703 ret
= trf7970a_tg_config_rf_tech(trf
, param
);
1705 case NFC_DIGITAL_CONFIG_FRAMING
:
1706 ret
= trf7970a_tg_config_framing(trf
, param
);
1709 dev_dbg(trf
->dev
, "Unknown type: %d\n", type
);
1714 mutex_unlock(&trf
->lock
);
1718 static int _trf7970a_tg_listen(struct nfc_digital_dev
*ddev
, u16 timeout
,
1719 nfc_digital_cmd_complete_t cb
, void *arg
,
1722 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1725 mutex_lock(&trf
->lock
);
1727 if ((trf
->state
!= TRF7970A_ST_IDLE
) &&
1728 (trf
->state
!= TRF7970A_ST_IDLE_RX_BLOCKED
)) {
1729 dev_err(trf
->dev
, "%s - Bogus state: %d\n", __func__
,
1735 if (trf
->aborting
) {
1736 dev_dbg(trf
->dev
, "Abort process complete\n");
1737 trf
->aborting
= false;
1742 trf
->rx_skb
= nfc_alloc_recv_skb(TRF7970A_RX_SKB_ALLOC_SIZE
,
1745 dev_dbg(trf
->dev
, "Can't alloc rx_skb\n");
1750 ret
= trf7970a_write(trf
, TRF7970A_RX_SPECIAL_SETTINGS
,
1751 TRF7970A_RX_SPECIAL_SETTINGS_HBT
|
1752 TRF7970A_RX_SPECIAL_SETTINGS_M848
|
1753 TRF7970A_RX_SPECIAL_SETTINGS_C424
|
1754 TRF7970A_RX_SPECIAL_SETTINGS_C212
);
1758 ret
= trf7970a_write(trf
, TRF7970A_REG_IO_CTRL
,
1759 trf
->io_ctrl
| TRF7970A_REG_IO_CTRL_VRS(0x1));
1763 ret
= trf7970a_write(trf
, TRF7970A_NFC_LOW_FIELD_LEVEL
,
1764 TRF7970A_NFC_LOW_FIELD_LEVEL_RFDET(0x3));
1768 ret
= trf7970a_write(trf
, TRF7970A_NFC_TARGET_LEVEL
,
1769 TRF7970A_NFC_TARGET_LEVEL_RFDET(0x7));
1776 trf
->timeout
= timeout
;
1777 trf
->ignore_timeout
= false;
1779 ret
= trf7970a_cmd(trf
, TRF7970A_CMD_ENABLE_RX
);
1783 trf
->state
= mode_detect
? TRF7970A_ST_LISTENING_MD
:
1784 TRF7970A_ST_LISTENING
;
1786 schedule_delayed_work(&trf
->timeout_work
, msecs_to_jiffies(timeout
));
1789 mutex_unlock(&trf
->lock
);
1793 static int trf7970a_tg_listen(struct nfc_digital_dev
*ddev
, u16 timeout
,
1794 nfc_digital_cmd_complete_t cb
, void *arg
)
1796 const struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1798 dev_dbg(trf
->dev
, "Listen - state: %d, timeout: %d ms\n",
1799 trf
->state
, timeout
);
1801 return _trf7970a_tg_listen(ddev
, timeout
, cb
, arg
, false);
1804 static int trf7970a_tg_listen_md(struct nfc_digital_dev
*ddev
,
1805 u16 timeout
, nfc_digital_cmd_complete_t cb
,
1808 const struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1811 dev_dbg(trf
->dev
, "Listen MD - state: %d, timeout: %d ms\n",
1812 trf
->state
, timeout
);
1814 ret
= trf7970a_tg_configure_hw(ddev
, NFC_DIGITAL_CONFIG_RF_TECH
,
1815 NFC_DIGITAL_RF_TECH_106A
);
1819 ret
= trf7970a_tg_configure_hw(ddev
, NFC_DIGITAL_CONFIG_FRAMING
,
1820 NFC_DIGITAL_FRAMING_NFCA_NFC_DEP
);
1824 return _trf7970a_tg_listen(ddev
, timeout
, cb
, arg
, true);
1827 static int trf7970a_tg_get_rf_tech(struct nfc_digital_dev
*ddev
, u8
*rf_tech
)
1829 const struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1831 dev_dbg(trf
->dev
, "Get RF Tech - state: %d, rf_tech: %d\n",
1832 trf
->state
, trf
->md_rf_tech
);
1834 *rf_tech
= trf
->md_rf_tech
;
1839 static void trf7970a_abort_cmd(struct nfc_digital_dev
*ddev
)
1841 struct trf7970a
*trf
= nfc_digital_get_drvdata(ddev
);
1843 dev_dbg(trf
->dev
, "Abort process initiated\n");
1845 mutex_lock(&trf
->lock
);
1847 switch (trf
->state
) {
1848 case TRF7970A_ST_WAIT_FOR_TX_FIFO
:
1849 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
1850 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
1851 case TRF7970A_ST_WAIT_TO_ISSUE_EOF
:
1852 trf
->aborting
= true;
1854 case TRF7970A_ST_LISTENING
:
1855 trf
->ignore_timeout
= !cancel_delayed_work(&trf
->timeout_work
);
1856 trf7970a_send_err_upstream(trf
, -ECANCELED
);
1857 dev_dbg(trf
->dev
, "Abort process complete\n");
1863 mutex_unlock(&trf
->lock
);
1866 static const struct nfc_digital_ops trf7970a_nfc_ops
= {
1867 .in_configure_hw
= trf7970a_in_configure_hw
,
1868 .in_send_cmd
= trf7970a_send_cmd
,
1869 .tg_configure_hw
= trf7970a_tg_configure_hw
,
1870 .tg_send_cmd
= trf7970a_send_cmd
,
1871 .tg_listen
= trf7970a_tg_listen
,
1872 .tg_listen_md
= trf7970a_tg_listen_md
,
1873 .tg_get_rf_tech
= trf7970a_tg_get_rf_tech
,
1874 .switch_rf
= trf7970a_switch_rf
,
1875 .abort_cmd
= trf7970a_abort_cmd
,
1878 static int trf7970a_power_up(struct trf7970a
*trf
)
1882 dev_dbg(trf
->dev
, "Powering up - state: %d\n", trf
->state
);
1884 if (trf
->state
!= TRF7970A_ST_PWR_OFF
)
1887 ret
= regulator_enable(trf
->vin_regulator
);
1889 dev_err(trf
->dev
, "%s - Can't enable VIN: %d\n", __func__
, ret
);
1893 usleep_range(5000, 6000);
1895 if (trf
->en2_gpiod
&&
1896 !(trf
->quirks
& TRF7970A_QUIRK_EN2_MUST_STAY_LOW
)) {
1897 gpiod_set_value_cansleep(trf
->en2_gpiod
, 1);
1898 usleep_range(1000, 2000);
1901 gpiod_set_value_cansleep(trf
->en_gpiod
, 1);
1903 usleep_range(20000, 21000);
1905 trf
->state
= TRF7970A_ST_RF_OFF
;
1910 static int trf7970a_power_down(struct trf7970a
*trf
)
1914 dev_dbg(trf
->dev
, "Powering down - state: %d\n", trf
->state
);
1916 if (trf
->state
== TRF7970A_ST_PWR_OFF
)
1919 if (trf
->state
!= TRF7970A_ST_RF_OFF
) {
1920 dev_dbg(trf
->dev
, "Can't power down - not RF_OFF state (%d)\n",
1925 gpiod_set_value_cansleep(trf
->en_gpiod
, 0);
1927 if (trf
->en2_gpiod
&& !(trf
->quirks
& TRF7970A_QUIRK_EN2_MUST_STAY_LOW
))
1928 gpiod_set_value_cansleep(trf
->en2_gpiod
, 0);
1930 ret
= regulator_disable(trf
->vin_regulator
);
1932 dev_err(trf
->dev
, "%s - Can't disable VIN: %d\n", __func__
,
1935 trf
->state
= TRF7970A_ST_PWR_OFF
;
1940 static int trf7970a_startup(struct trf7970a
*trf
)
1944 ret
= trf7970a_power_up(trf
);
1948 pm_runtime_set_active(trf
->dev
);
1949 pm_runtime_enable(trf
->dev
);
1950 pm_runtime_mark_last_busy(trf
->dev
);
1955 static void trf7970a_shutdown(struct trf7970a
*trf
)
1957 switch (trf
->state
) {
1958 case TRF7970A_ST_WAIT_FOR_TX_FIFO
:
1959 case TRF7970A_ST_WAIT_FOR_RX_DATA
:
1960 case TRF7970A_ST_WAIT_FOR_RX_DATA_CONT
:
1961 case TRF7970A_ST_WAIT_TO_ISSUE_EOF
:
1962 case TRF7970A_ST_LISTENING
:
1963 trf7970a_send_err_upstream(trf
, -ECANCELED
);
1965 case TRF7970A_ST_IDLE
:
1966 case TRF7970A_ST_IDLE_RX_BLOCKED
:
1967 trf7970a_switch_rf_off(trf
);
1973 pm_runtime_disable(trf
->dev
);
1974 pm_runtime_set_suspended(trf
->dev
);
1976 trf7970a_power_down(trf
);
1979 static int trf7970a_get_autosuspend_delay(const struct device_node
*np
)
1981 int autosuspend_delay
, ret
;
1983 ret
= of_property_read_u32(np
, "autosuspend-delay", &autosuspend_delay
);
1985 autosuspend_delay
= TRF7970A_AUTOSUSPEND_DELAY
;
1987 return autosuspend_delay
;
1990 static int trf7970a_probe(struct spi_device
*spi
)
1992 const struct device_node
*np
= spi
->dev
.of_node
;
1993 struct trf7970a
*trf
;
1994 int uvolts
, autosuspend_delay
, ret
;
1995 u32 clk_freq
= TRF7970A_13MHZ_CLOCK_FREQUENCY
;
1998 dev_err(&spi
->dev
, "No Device Tree entry\n");
2002 trf
= devm_kzalloc(&spi
->dev
, sizeof(*trf
), GFP_KERNEL
);
2006 trf
->state
= TRF7970A_ST_PWR_OFF
;
2007 trf
->dev
= &spi
->dev
;
2010 spi
->mode
= SPI_MODE_1
;
2011 spi
->bits_per_word
= 8;
2013 ret
= spi_setup(spi
);
2015 dev_err(trf
->dev
, "Can't set up SPI Communication\n");
2019 if (of_property_read_bool(np
, "irq-status-read-quirk"))
2020 trf
->quirks
|= TRF7970A_QUIRK_IRQ_STATUS_READ
;
2022 /* There are two enable pins - only EN must be present in the DT */
2023 trf
->en_gpiod
= devm_gpiod_get_index(trf
->dev
, "ti,enable", 0,
2025 if (IS_ERR(trf
->en_gpiod
)) {
2026 dev_err(trf
->dev
, "No EN GPIO property\n");
2027 return PTR_ERR(trf
->en_gpiod
);
2030 trf
->en2_gpiod
= devm_gpiod_get_index_optional(trf
->dev
, "ti,enable", 1,
2032 if (!trf
->en2_gpiod
) {
2033 dev_info(trf
->dev
, "No EN2 GPIO property\n");
2034 } else if (IS_ERR(trf
->en2_gpiod
)) {
2035 dev_err(trf
->dev
, "Error getting EN2 GPIO property: %ld\n",
2036 PTR_ERR(trf
->en2_gpiod
));
2037 return PTR_ERR(trf
->en2_gpiod
);
2038 } else if (of_property_read_bool(np
, "en2-rf-quirk")) {
2039 trf
->quirks
|= TRF7970A_QUIRK_EN2_MUST_STAY_LOW
;
2042 of_property_read_u32(np
, "clock-frequency", &clk_freq
);
2043 if ((clk_freq
!= TRF7970A_27MHZ_CLOCK_FREQUENCY
) &&
2044 (clk_freq
!= TRF7970A_13MHZ_CLOCK_FREQUENCY
)) {
2046 "clock-frequency (%u Hz) unsupported\n", clk_freq
);
2050 if (clk_freq
== TRF7970A_27MHZ_CLOCK_FREQUENCY
) {
2051 trf
->modulator_sys_clk_ctrl
= TRF7970A_MODULATOR_27MHZ
;
2052 dev_dbg(trf
->dev
, "trf7970a configured for 27MHz crystal\n");
2054 trf
->modulator_sys_clk_ctrl
= 0;
2057 ret
= devm_request_threaded_irq(trf
->dev
, spi
->irq
, NULL
,
2059 IRQF_TRIGGER_RISING
| IRQF_ONESHOT
,
2062 dev_err(trf
->dev
, "Can't request IRQ#%d: %d\n", spi
->irq
, ret
);
2066 mutex_init(&trf
->lock
);
2067 INIT_DELAYED_WORK(&trf
->timeout_work
, trf7970a_timeout_work_handler
);
2069 trf
->vin_regulator
= devm_regulator_get(&spi
->dev
, "vin");
2070 if (IS_ERR(trf
->vin_regulator
)) {
2071 ret
= PTR_ERR(trf
->vin_regulator
);
2072 dev_err(trf
->dev
, "Can't get VIN regulator: %d\n", ret
);
2073 goto err_destroy_lock
;
2076 ret
= regulator_enable(trf
->vin_regulator
);
2078 dev_err(trf
->dev
, "Can't enable VIN: %d\n", ret
);
2079 goto err_destroy_lock
;
2082 uvolts
= regulator_get_voltage(trf
->vin_regulator
);
2083 if (uvolts
> 4000000)
2084 trf
->chip_status_ctrl
= TRF7970A_CHIP_STATUS_VRS5_3
;
2086 trf
->vddio_regulator
= devm_regulator_get(&spi
->dev
, "vdd-io");
2087 if (IS_ERR(trf
->vddio_regulator
)) {
2088 ret
= PTR_ERR(trf
->vddio_regulator
);
2089 dev_err(trf
->dev
, "Can't get VDD_IO regulator: %d\n", ret
);
2090 goto err_disable_vin_regulator
;
2093 ret
= regulator_enable(trf
->vddio_regulator
);
2095 dev_err(trf
->dev
, "Can't enable VDD_IO: %d\n", ret
);
2096 goto err_disable_vin_regulator
;
2099 if (regulator_get_voltage(trf
->vddio_regulator
) == 1800000) {
2100 trf
->io_ctrl
= TRF7970A_REG_IO_CTRL_IO_LOW
;
2101 dev_dbg(trf
->dev
, "trf7970a config vdd_io to 1.8V\n");
2104 trf
->ddev
= nfc_digital_allocate_device(&trf7970a_nfc_ops
,
2105 TRF7970A_SUPPORTED_PROTOCOLS
,
2106 NFC_DIGITAL_DRV_CAPS_IN_CRC
|
2107 NFC_DIGITAL_DRV_CAPS_TG_CRC
, 0,
2110 dev_err(trf
->dev
, "Can't allocate NFC digital device\n");
2112 goto err_disable_vddio_regulator
;
2115 nfc_digital_set_parent_dev(trf
->ddev
, trf
->dev
);
2116 nfc_digital_set_drvdata(trf
->ddev
, trf
);
2117 spi_set_drvdata(spi
, trf
);
2119 autosuspend_delay
= trf7970a_get_autosuspend_delay(np
);
2121 pm_runtime_set_autosuspend_delay(trf
->dev
, autosuspend_delay
);
2122 pm_runtime_use_autosuspend(trf
->dev
);
2124 ret
= trf7970a_startup(trf
);
2128 ret
= nfc_digital_register_device(trf
->ddev
);
2130 dev_err(trf
->dev
, "Can't register NFC digital device: %d\n",
2138 trf7970a_shutdown(trf
);
2140 nfc_digital_free_device(trf
->ddev
);
2141 err_disable_vddio_regulator
:
2142 regulator_disable(trf
->vddio_regulator
);
2143 err_disable_vin_regulator
:
2144 regulator_disable(trf
->vin_regulator
);
2146 mutex_destroy(&trf
->lock
);
2150 static void trf7970a_remove(struct spi_device
*spi
)
2152 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2154 mutex_lock(&trf
->lock
);
2156 trf7970a_shutdown(trf
);
2158 mutex_unlock(&trf
->lock
);
2160 nfc_digital_unregister_device(trf
->ddev
);
2161 nfc_digital_free_device(trf
->ddev
);
2163 regulator_disable(trf
->vddio_regulator
);
2164 regulator_disable(trf
->vin_regulator
);
2166 mutex_destroy(&trf
->lock
);
2169 #ifdef CONFIG_PM_SLEEP
2170 static int trf7970a_suspend(struct device
*dev
)
2172 struct spi_device
*spi
= to_spi_device(dev
);
2173 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2175 mutex_lock(&trf
->lock
);
2177 trf7970a_shutdown(trf
);
2179 mutex_unlock(&trf
->lock
);
2184 static int trf7970a_resume(struct device
*dev
)
2186 struct spi_device
*spi
= to_spi_device(dev
);
2187 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2190 mutex_lock(&trf
->lock
);
2192 ret
= trf7970a_startup(trf
);
2194 mutex_unlock(&trf
->lock
);
2201 static int trf7970a_pm_runtime_suspend(struct device
*dev
)
2203 struct spi_device
*spi
= to_spi_device(dev
);
2204 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2207 mutex_lock(&trf
->lock
);
2209 ret
= trf7970a_power_down(trf
);
2211 mutex_unlock(&trf
->lock
);
2216 static int trf7970a_pm_runtime_resume(struct device
*dev
)
2218 struct spi_device
*spi
= to_spi_device(dev
);
2219 struct trf7970a
*trf
= spi_get_drvdata(spi
);
2222 ret
= trf7970a_power_up(trf
);
2224 pm_runtime_mark_last_busy(dev
);
2230 static const struct dev_pm_ops trf7970a_pm_ops
= {
2231 SET_SYSTEM_SLEEP_PM_OPS(trf7970a_suspend
, trf7970a_resume
)
2232 SET_RUNTIME_PM_OPS(trf7970a_pm_runtime_suspend
,
2233 trf7970a_pm_runtime_resume
, NULL
)
2236 static const struct of_device_id trf7970a_of_match
[] __maybe_unused
= {
2237 {.compatible
= "ti,trf7970a",},
2241 MODULE_DEVICE_TABLE(of
, trf7970a_of_match
);
2243 static const struct spi_device_id trf7970a_id_table
[] = {
2248 MODULE_DEVICE_TABLE(spi
, trf7970a_id_table
);
2250 static struct spi_driver trf7970a_spi_driver
= {
2251 .probe
= trf7970a_probe
,
2252 .remove
= trf7970a_remove
,
2253 .id_table
= trf7970a_id_table
,
2256 .of_match_table
= of_match_ptr(trf7970a_of_match
),
2257 .pm
= &trf7970a_pm_ops
,
2261 module_spi_driver(trf7970a_spi_driver
);
2263 MODULE_AUTHOR("Mark A. Greer <mgreer@animalcreek.com>");
2264 MODULE_LICENSE("GPL v2");
2265 MODULE_DESCRIPTION("TI trf7970a RFID/NFC Transceiver Driver");