1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Bt8xx based DVB adapter driver
5 * Copyright (C) 2002,2003 Florian Schirmer <jolt@tuxbox.org>
8 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
10 #include <linux/bitops.h>
11 #include <linux/module.h>
12 #include <linux/init.h>
13 #include <linux/kernel.h>
14 #include <linux/device.h>
15 #include <linux/delay.h>
16 #include <linux/slab.h>
17 #include <linux/i2c.h>
19 #include <media/dmxdev.h>
20 #include <media/dvbdev.h>
21 #include <media/dvb_demux.h>
22 #include <media/dvb_frontend.h>
23 #include "dvb-bt8xx.h"
28 module_param(debug
, int, 0644);
29 MODULE_PARM_DESC(debug
, "Turn on/off debugging (default:off).");
31 DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr
);
33 #define dprintk(fmt, arg...) do { \
35 printk(KERN_DEBUG pr_fmt("%s: " fmt), \
40 #define IF_FREQUENCYx6 217 /* 6 * 36.16666666667MHz */
42 static void dvb_bt8xx_work(struct work_struct
*t
)
44 struct bt878
*bt
= from_work(bt
, t
, bh_work
);
45 struct dvb_bt8xx_card
*card
= dev_get_drvdata(&bt
->adapter
->dev
);
47 dprintk("%d\n", card
->bt
->finished_block
);
49 while (card
->bt
->last_block
!= card
->bt
->finished_block
) {
50 (card
->bt
->TS_Size
? dvb_dmx_swfilter_204
: dvb_dmx_swfilter
)
52 &card
->bt
->buf_cpu
[card
->bt
->last_block
*
53 card
->bt
->block_bytes
],
54 card
->bt
->block_bytes
);
55 card
->bt
->last_block
= (card
->bt
->last_block
+ 1) %
56 card
->bt
->block_count
;
60 static int dvb_bt8xx_start_feed(struct dvb_demux_feed
*dvbdmxfeed
)
62 struct dvb_demux
*dvbdmx
= dvbdmxfeed
->demux
;
63 struct dvb_bt8xx_card
*card
= dvbdmx
->priv
;
66 dprintk("dvb_bt8xx: start_feed\n");
68 if (!dvbdmx
->dmx
.frontend
)
71 mutex_lock(&card
->lock
);
74 if (card
->nfeeds
== 1)
75 bt878_start(card
->bt
, card
->gpio_mode
,
76 card
->op_sync_orin
, card
->irq_err_ignore
);
77 mutex_unlock(&card
->lock
);
81 static int dvb_bt8xx_stop_feed(struct dvb_demux_feed
*dvbdmxfeed
)
83 struct dvb_demux
*dvbdmx
= dvbdmxfeed
->demux
;
84 struct dvb_bt8xx_card
*card
= dvbdmx
->priv
;
86 dprintk("dvb_bt8xx: stop_feed\n");
88 if (!dvbdmx
->dmx
.frontend
)
91 mutex_lock(&card
->lock
);
93 if (card
->nfeeds
== 0)
95 mutex_unlock(&card
->lock
);
100 static int is_pci_slot_eq(struct pci_dev
* adev
, struct pci_dev
* bdev
)
102 if ((adev
->subsystem_vendor
== bdev
->subsystem_vendor
) &&
103 (adev
->subsystem_device
== bdev
->subsystem_device
) &&
104 (adev
->bus
->number
== bdev
->bus
->number
) &&
105 (PCI_SLOT(adev
->devfn
) == PCI_SLOT(bdev
->devfn
)))
110 static struct bt878
*dvb_bt8xx_878_match(unsigned int bttv_nr
,
111 struct pci_dev
* bttv_pci_dev
)
113 unsigned int card_nr
;
115 /* Hmm, n squared. Hope n is small */
116 for (card_nr
= 0; card_nr
< bt878_num
; card_nr
++)
117 if (is_pci_slot_eq(bt878
[card_nr
].dev
, bttv_pci_dev
))
118 return &bt878
[card_nr
];
122 static int thomson_dtt7579_demod_init(struct dvb_frontend
* fe
)
124 static u8 mt352_clock_config
[] = { 0x89, 0x38, 0x38 };
125 static u8 mt352_reset
[] = { 0x50, 0x80 };
126 static u8 mt352_adc_ctl_1_cfg
[] = { 0x8E, 0x40 };
127 static u8 mt352_agc_cfg
[] = { 0x67, 0x28, 0x20 };
128 static u8 mt352_gpp_ctl_cfg
[] = { 0x8C, 0x33 };
129 static u8 mt352_capt_range_cfg
[] = { 0x75, 0x32 };
131 mt352_write(fe
, mt352_clock_config
, sizeof(mt352_clock_config
));
133 mt352_write(fe
, mt352_reset
, sizeof(mt352_reset
));
134 mt352_write(fe
, mt352_adc_ctl_1_cfg
, sizeof(mt352_adc_ctl_1_cfg
));
136 mt352_write(fe
, mt352_agc_cfg
, sizeof(mt352_agc_cfg
));
137 mt352_write(fe
, mt352_gpp_ctl_cfg
, sizeof(mt352_gpp_ctl_cfg
));
138 mt352_write(fe
, mt352_capt_range_cfg
, sizeof(mt352_capt_range_cfg
));
143 static int thomson_dtt7579_tuner_calc_regs(struct dvb_frontend
*fe
, u8
* pllbuf
, int buf_len
)
145 struct dtv_frontend_properties
*c
= &fe
->dtv_property_cache
;
147 unsigned char bs
= 0;
148 unsigned char cp
= 0;
153 div
= (((c
->frequency
+ 83333) * 3) / 500000) + IF_FREQUENCYx6
;
155 if (c
->frequency
< 542000000)
157 else if (c
->frequency
< 771000000)
162 if (c
->frequency
== 0)
164 else if (c
->frequency
< 443250000)
170 pllbuf
[1] = div
>> 8;
171 pllbuf
[2] = div
& 0xff;
178 static struct mt352_config thomson_dtt7579_config
= {
179 .demod_address
= 0x0f,
180 .demod_init
= thomson_dtt7579_demod_init
,
183 static struct zl10353_config thomson_dtt7579_zl10353_config
= {
184 .demod_address
= 0x0f,
187 static int cx24108_tuner_set_params(struct dvb_frontend
*fe
)
189 struct dtv_frontend_properties
*c
= &fe
->dtv_property_cache
;
190 u32 freq
= c
->frequency
;
193 static const u32 osci
[] = {
194 950000, 1019000, 1075000, 1178000, 1296000, 1432000,
195 1576000, 1718000, 1856000, 2036000, 2150000
197 static const u32 bandsel
[] = {
198 0, 0x00020000, 0x00040000, 0x00100800, 0x00101000,
199 0x00102000, 0x00104000, 0x00108000, 0x00110000,
200 0x00120000, 0x00140000
203 #define XTAL 1011100 /* Hz, really 1.0111 MHz and a /10 prescaler */
204 dprintk("cx24108 debug: entering SetTunerFreq, freq=%d\n", freq
);
206 /* This is really the bit driving the tuner chip cx24108 */
209 freq
= 950000; /* kHz */
210 else if (freq
>2150000)
211 freq
= 2150000; /* satellite IF is 950..2150MHz */
213 /* decide which VCO to use for the input frequency */
214 for(i
= 1; (i
< ARRAY_SIZE(osci
) - 1) && (osci
[i
] < freq
); i
++);
215 dprintk("cx24108 debug: select vco #%d (f=%d)\n", i
, freq
);
217 /* the gain values must be set by SetSymbolrate */
218 /* compute the pll divider needed, from Conexant data sheet,
219 resolved for (n*32+a), remember f(vco) is f(receive) *2 or *4,
220 depending on the divider bit. It is set to /4 on the 2 lowest
222 n
=((i
<=2?2:1)*freq
*10L)/(XTAL
/100);
223 a
=n
%32; n
/=32; if(a
==0) n
--;
224 pump
=(freq
<(osci
[i
-1]+osci
[i
])/2);
226 ((pump
?1:2)<<(14+11))|
229 /* everything is shifted left 11 bits to left-align the bits in the
230 32bit word. Output to the tuner goes MSB-aligned, after all */
231 dprintk("cx24108 debug: pump=%d, n=%d, a=%d\n", pump
, n
, a
);
232 cx24110_pll_write(fe
,band
);
233 /* set vga and vca to their widest-band settings, as a precaution.
234 SetSymbolrate might not be called to set this up */
235 cx24110_pll_write(fe
,0x500c0000);
236 cx24110_pll_write(fe
,0x83f1f800);
237 cx24110_pll_write(fe
,pll
);
238 //writereg(client,0x56,0x7f);
243 static int pinnsat_tuner_init(struct dvb_frontend
* fe
)
245 struct dvb_bt8xx_card
*card
= fe
->dvb
->priv
;
247 bttv_gpio_enable(card
->bttv_nr
, 1, 1); /* output */
248 bttv_write_gpio(card
->bttv_nr
, 1, 1); /* relay on */
253 static int pinnsat_tuner_sleep(struct dvb_frontend
* fe
)
255 struct dvb_bt8xx_card
*card
= fe
->dvb
->priv
;
257 bttv_write_gpio(card
->bttv_nr
, 1, 0); /* relay off */
262 static struct cx24110_config pctvsat_config
= {
263 .demod_address
= 0x55,
266 static int microtune_mt7202dtf_tuner_set_params(struct dvb_frontend
*fe
)
268 struct dtv_frontend_properties
*c
= &fe
->dtv_property_cache
;
269 struct dvb_bt8xx_card
*card
= (struct dvb_bt8xx_card
*) fe
->dvb
->priv
;
270 u8 cfg
, cpump
, band_select
;
273 struct i2c_msg msg
= { .addr
= 0x60, .flags
= 0, .buf
= data
, .len
= sizeof(data
) };
275 div
= (36000000 + c
->frequency
+ 83333) / 166666;
278 if (c
->frequency
< 175000000)
280 else if (c
->frequency
< 390000000)
282 else if (c
->frequency
< 470000000)
284 else if (c
->frequency
< 750000000)
289 if (c
->frequency
< 175000000)
291 else if (c
->frequency
< 470000000)
296 data
[0] = (div
>> 8) & 0x7f;
297 data
[1] = div
& 0xff;
298 data
[2] = ((div
>> 10) & 0x60) | cfg
;
299 data
[3] = (cpump
<< 6) | band_select
;
301 if (fe
->ops
.i2c_gate_ctrl
)
302 fe
->ops
.i2c_gate_ctrl(fe
, 1);
303 i2c_transfer(card
->i2c_adapter
, &msg
, 1);
304 return (div
* 166666 - 36000000);
307 static int microtune_mt7202dtf_request_firmware(struct dvb_frontend
* fe
, const struct firmware
**fw
, char* name
)
309 struct dvb_bt8xx_card
* bt
= (struct dvb_bt8xx_card
*) fe
->dvb
->priv
;
311 return request_firmware(fw
, name
, &bt
->bt
->dev
->dev
);
314 static const struct sp887x_config microtune_mt7202dtf_config
= {
315 .demod_address
= 0x70,
316 .request_firmware
= microtune_mt7202dtf_request_firmware
,
319 static int advbt771_samsung_tdtc9251dh0_demod_init(struct dvb_frontend
* fe
)
321 static u8 mt352_clock_config
[] = { 0x89, 0x38, 0x2d };
322 static u8 mt352_reset
[] = { 0x50, 0x80 };
323 static u8 mt352_adc_ctl_1_cfg
[] = { 0x8E, 0x40 };
324 static u8 mt352_agc_cfg
[] = { 0x67, 0x10, 0x23, 0x00, 0xFF, 0xFF,
325 0x00, 0xFF, 0x00, 0x40, 0x40 };
326 static u8 mt352_av771_extra
[] = { 0xB5, 0x7A };
327 static u8 mt352_capt_range_cfg
[] = { 0x75, 0x32 };
329 mt352_write(fe
, mt352_clock_config
, sizeof(mt352_clock_config
));
331 mt352_write(fe
, mt352_reset
, sizeof(mt352_reset
));
332 mt352_write(fe
, mt352_adc_ctl_1_cfg
, sizeof(mt352_adc_ctl_1_cfg
));
334 mt352_write(fe
, mt352_agc_cfg
,sizeof(mt352_agc_cfg
));
336 mt352_write(fe
, mt352_av771_extra
,sizeof(mt352_av771_extra
));
337 mt352_write(fe
, mt352_capt_range_cfg
, sizeof(mt352_capt_range_cfg
));
342 static int advbt771_samsung_tdtc9251dh0_tuner_calc_regs(struct dvb_frontend
*fe
, u8
*pllbuf
, int buf_len
)
344 struct dtv_frontend_properties
*c
= &fe
->dtv_property_cache
;
346 unsigned char bs
= 0;
347 unsigned char cp
= 0;
349 if (buf_len
< 5) return -EINVAL
;
351 div
= (((c
->frequency
+ 83333) * 3) / 500000) + IF_FREQUENCYx6
;
353 if (c
->frequency
< 150000000)
355 else if (c
->frequency
< 173000000)
357 else if (c
->frequency
< 250000000)
359 else if (c
->frequency
< 400000000)
361 else if (c
->frequency
< 420000000)
363 else if (c
->frequency
< 470000000)
365 else if (c
->frequency
< 600000000)
367 else if (c
->frequency
< 730000000)
372 if (c
->frequency
< 150000000)
374 else if (c
->frequency
< 173000000)
376 else if (c
->frequency
< 250000000)
378 else if (c
->frequency
< 400000000)
380 else if (c
->frequency
< 420000000)
382 else if (c
->frequency
< 470000000)
388 pllbuf
[1] = div
>> 8;
389 pllbuf
[2] = div
& 0xff;
396 static struct mt352_config advbt771_samsung_tdtc9251dh0_config
= {
397 .demod_address
= 0x0f,
398 .demod_init
= advbt771_samsung_tdtc9251dh0_demod_init
,
401 static const struct dst_config dst_config
= {
402 .demod_address
= 0x55,
405 static int or51211_request_firmware(struct dvb_frontend
* fe
, const struct firmware
**fw
, char* name
)
407 struct dvb_bt8xx_card
* bt
= (struct dvb_bt8xx_card
*) fe
->dvb
->priv
;
409 return request_firmware(fw
, name
, &bt
->bt
->dev
->dev
);
412 static void or51211_setmode(struct dvb_frontend
* fe
, int mode
)
414 struct dvb_bt8xx_card
*bt
= fe
->dvb
->priv
;
415 bttv_write_gpio(bt
->bttv_nr
, 0x0002, mode
); /* Reset */
419 static void or51211_reset(struct dvb_frontend
* fe
)
421 struct dvb_bt8xx_card
*bt
= fe
->dvb
->priv
;
424 * reset is controlled by GPIO-0
425 * when set to 0 causes reset and when to 1 for normal op
426 * must remain reset for 128 clock cycles on a 50Mhz clock
427 * also PRM1 PRM2 & PRM4 are controlled by GPIO-1,GPIO-2 & GPIO-4
428 * We assume that the reset has be held low long enough or we
429 * have been reset by a power on. When the driver is unloaded
430 * reset set to 0 so if reloaded we have been reset.
432 /* reset & PRM1,2&4 are outputs */
433 int ret
= bttv_gpio_enable(bt
->bttv_nr
, 0x001F, 0x001F);
435 pr_warn("or51211: Init Error - Can't Reset DVR (%i)\n", ret
);
436 bttv_write_gpio(bt
->bttv_nr
, 0x001F, 0x0000); /* Reset */
438 /* Now set for normal operation */
439 bttv_write_gpio(bt
->bttv_nr
, 0x0001F, 0x0001);
440 /* wait for operation to begin */
444 static void or51211_sleep(struct dvb_frontend
* fe
)
446 struct dvb_bt8xx_card
*bt
= fe
->dvb
->priv
;
447 bttv_write_gpio(bt
->bttv_nr
, 0x0001, 0x0000);
450 static const struct or51211_config or51211_config
= {
451 .demod_address
= 0x15,
452 .request_firmware
= or51211_request_firmware
,
453 .setmode
= or51211_setmode
,
454 .reset
= or51211_reset
,
455 .sleep
= or51211_sleep
,
458 static int vp3021_alps_tded4_tuner_set_params(struct dvb_frontend
*fe
)
460 struct dtv_frontend_properties
*c
= &fe
->dtv_property_cache
;
461 struct dvb_bt8xx_card
*card
= (struct dvb_bt8xx_card
*) fe
->dvb
->priv
;
464 struct i2c_msg msg
= { .addr
= 0x60, .flags
= 0, .buf
= buf
, .len
= sizeof(buf
) };
466 div
= (c
->frequency
+ 36166667) / 166667;
468 buf
[0] = (div
>> 8) & 0x7F;
471 if ((c
->frequency
>= 47000000) && (c
->frequency
< 153000000))
473 else if ((c
->frequency
>= 153000000) && (c
->frequency
< 430000000))
475 else if ((c
->frequency
>= 430000000) && (c
->frequency
< 824000000))
477 else if ((c
->frequency
>= 824000000) && (c
->frequency
< 863000000))
482 if (fe
->ops
.i2c_gate_ctrl
)
483 fe
->ops
.i2c_gate_ctrl(fe
, 1);
484 i2c_transfer(card
->i2c_adapter
, &msg
, 1);
488 static struct nxt6000_config vp3021_alps_tded4_config
= {
489 .demod_address
= 0x0a,
490 .clock_inversion
= 1,
493 static int digitv_alps_tded4_demod_init(struct dvb_frontend
* fe
)
495 static u8 mt352_clock_config
[] = { 0x89, 0x38, 0x2d };
496 static u8 mt352_reset
[] = { 0x50, 0x80 };
497 static u8 mt352_adc_ctl_1_cfg
[] = { 0x8E, 0x40 };
498 static u8 mt352_agc_cfg
[] = { 0x67, 0x20, 0xa0 };
499 static u8 mt352_capt_range_cfg
[] = { 0x75, 0x32 };
501 mt352_write(fe
, mt352_clock_config
, sizeof(mt352_clock_config
));
503 mt352_write(fe
, mt352_reset
, sizeof(mt352_reset
));
504 mt352_write(fe
, mt352_adc_ctl_1_cfg
, sizeof(mt352_adc_ctl_1_cfg
));
505 mt352_write(fe
, mt352_agc_cfg
,sizeof(mt352_agc_cfg
));
506 mt352_write(fe
, mt352_capt_range_cfg
, sizeof(mt352_capt_range_cfg
));
511 static int digitv_alps_tded4_tuner_calc_regs(struct dvb_frontend
*fe
, u8
*pllbuf
, int buf_len
)
514 struct dtv_frontend_properties
*c
= &fe
->dtv_property_cache
;
519 div
= (((c
->frequency
+ 83333) * 3) / 500000) + IF_FREQUENCYx6
;
522 pllbuf
[1] = (div
>> 8) & 0x7F;
523 pllbuf
[2] = div
& 0xFF;
526 dprintk("frequency %u, div %u\n", c
->frequency
, div
);
528 if (c
->frequency
< 470000000)
530 else if (c
->frequency
> 823000000)
535 if (c
->bandwidth_hz
== 8000000)
541 static void digitv_alps_tded4_reset(struct dvb_bt8xx_card
*bt
)
544 * Reset the frontend, must be called before trying
545 * to initialise the MT352 or mt352_attach
546 * will fail. Same goes for the nxt6000 frontend.
550 int ret
= bttv_gpio_enable(bt
->bttv_nr
, 0x08, 0x08);
552 pr_warn("digitv_alps_tded4: Init Error - Can't Reset DVR (%i)\n",
555 /* Pulse the reset line */
556 bttv_write_gpio(bt
->bttv_nr
, 0x08, 0x08); /* High */
557 bttv_write_gpio(bt
->bttv_nr
, 0x08, 0x00); /* Low */
560 bttv_write_gpio(bt
->bttv_nr
, 0x08, 0x08); /* High */
563 static struct mt352_config digitv_alps_tded4_config
= {
564 .demod_address
= 0x0a,
565 .demod_init
= digitv_alps_tded4_demod_init
,
568 static struct lgdt330x_config tdvs_tua6034_config
= {
569 .demod_chip
= LGDT3303
,
570 .serial_mpeg
= 0x40, /* TPSERIAL for 3303 in TOP_CONTROL */
573 static void lgdt330x_reset(struct dvb_bt8xx_card
*bt
)
575 /* Set pin 27 of the lgdt3303 chip high to reset the frontend */
577 /* Pulse the reset line */
578 bttv_write_gpio(bt
->bttv_nr
, 0x00e00007, 0x00000001); /* High */
579 bttv_write_gpio(bt
->bttv_nr
, 0x00e00007, 0x00000000); /* Low */
582 bttv_write_gpio(bt
->bttv_nr
, 0x00e00007, 0x00000001); /* High */
586 static void frontend_init(struct dvb_bt8xx_card
*card
, u32 type
)
588 struct dst_state
* state
= NULL
;
591 case BTTV_BOARD_DVICO_DVBT_LITE
:
592 card
->fe
= dvb_attach(mt352_attach
, &thomson_dtt7579_config
, card
->i2c_adapter
);
594 if (card
->fe
== NULL
)
595 card
->fe
= dvb_attach(zl10353_attach
, &thomson_dtt7579_zl10353_config
,
598 if (card
->fe
!= NULL
) {
599 card
->fe
->ops
.tuner_ops
.calc_regs
= thomson_dtt7579_tuner_calc_regs
;
600 card
->fe
->ops
.info
.frequency_min_hz
= 174 * MHz
;
601 card
->fe
->ops
.info
.frequency_max_hz
= 862 * MHz
;
605 case BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE
:
606 lgdt330x_reset(card
);
607 card
->fe
= dvb_attach(lgdt330x_attach
, &tdvs_tua6034_config
,
608 0x0e, card
->i2c_adapter
);
609 if (card
->fe
!= NULL
) {
610 dvb_attach(simple_tuner_attach
, card
->fe
,
611 card
->i2c_adapter
, 0x61,
612 TUNER_LG_TDVS_H06XF
);
613 dprintk("dvb_bt8xx: lgdt330x detected\n");
617 case BTTV_BOARD_NEBULA_DIGITV
:
619 * It is possible to determine the correct frontend using the I2C bus (see the Nebula SDK);
620 * this would be a cleaner solution than trying each frontend in turn.
623 /* Old Nebula (marked (c)2003 on high profile pci card) has nxt6000 demod */
624 digitv_alps_tded4_reset(card
);
625 card
->fe
= dvb_attach(nxt6000_attach
, &vp3021_alps_tded4_config
, card
->i2c_adapter
);
626 if (card
->fe
!= NULL
) {
627 card
->fe
->ops
.tuner_ops
.set_params
= vp3021_alps_tded4_tuner_set_params
;
628 dprintk("dvb_bt8xx: an nxt6000 was detected on your digitv card\n");
632 /* New Nebula (marked (c)2005 on low profile pci card) has mt352 demod */
633 digitv_alps_tded4_reset(card
);
634 card
->fe
= dvb_attach(mt352_attach
, &digitv_alps_tded4_config
, card
->i2c_adapter
);
636 if (card
->fe
!= NULL
) {
637 card
->fe
->ops
.tuner_ops
.calc_regs
= digitv_alps_tded4_tuner_calc_regs
;
638 dprintk("dvb_bt8xx: an mt352 was detected on your digitv card\n");
642 case BTTV_BOARD_AVDVBT_761
:
643 card
->fe
= dvb_attach(sp887x_attach
, µtune_mt7202dtf_config
, card
->i2c_adapter
);
645 card
->fe
->ops
.tuner_ops
.set_params
= microtune_mt7202dtf_tuner_set_params
;
649 case BTTV_BOARD_AVDVBT_771
:
650 card
->fe
= dvb_attach(mt352_attach
, &advbt771_samsung_tdtc9251dh0_config
, card
->i2c_adapter
);
651 if (card
->fe
!= NULL
) {
652 card
->fe
->ops
.tuner_ops
.calc_regs
= advbt771_samsung_tdtc9251dh0_tuner_calc_regs
;
653 card
->fe
->ops
.info
.frequency_min_hz
= 174 * MHz
;
654 card
->fe
->ops
.info
.frequency_max_hz
= 862 * MHz
;
658 case BTTV_BOARD_TWINHAN_DST
:
659 /* DST is not a frontend driver !!! */
660 state
= kmalloc(sizeof (struct dst_state
), GFP_KERNEL
);
662 pr_err("No memory\n");
666 state
->config
= &dst_config
;
667 state
->i2c
= card
->i2c_adapter
;
668 state
->bt
= card
->bt
;
669 state
->dst_ca
= NULL
;
670 /* DST is not a frontend, attaching the ASIC */
671 if (dvb_attach(dst_attach
, state
, &card
->dvb_adapter
) == NULL
) {
672 pr_err("%s: Could not find a Twinhan DST\n", __func__
);
676 /* Attach other DST peripherals if any */
677 /* Conditional Access device */
678 card
->fe
= &state
->frontend
;
679 if (state
->dst_hw_cap
& DST_TYPE_HAS_CA
)
680 dvb_attach(dst_ca_attach
, state
, &card
->dvb_adapter
);
683 case BTTV_BOARD_PINNACLESAT
:
684 card
->fe
= dvb_attach(cx24110_attach
, &pctvsat_config
, card
->i2c_adapter
);
686 card
->fe
->ops
.tuner_ops
.init
= pinnsat_tuner_init
;
687 card
->fe
->ops
.tuner_ops
.sleep
= pinnsat_tuner_sleep
;
688 card
->fe
->ops
.tuner_ops
.set_params
= cx24108_tuner_set_params
;
692 case BTTV_BOARD_PC_HDTV
:
693 card
->fe
= dvb_attach(or51211_attach
, &or51211_config
, card
->i2c_adapter
);
694 if (card
->fe
!= NULL
)
695 dvb_attach(simple_tuner_attach
, card
->fe
,
696 card
->i2c_adapter
, 0x61,
697 TUNER_PHILIPS_FCV1236D
);
701 if (card
->fe
== NULL
)
702 pr_err("A frontend driver was not found for device [%04x:%04x] subsystem [%04x:%04x]\n",
703 card
->bt
->dev
->vendor
,
704 card
->bt
->dev
->device
,
705 card
->bt
->dev
->subsystem_vendor
,
706 card
->bt
->dev
->subsystem_device
);
708 if (dvb_register_frontend(&card
->dvb_adapter
, card
->fe
)) {
709 pr_err("Frontend registration failed!\n");
710 dvb_frontend_detach(card
->fe
);
715 static int dvb_bt8xx_load_card(struct dvb_bt8xx_card
*card
, u32 type
)
719 result
= dvb_register_adapter(&card
->dvb_adapter
, card
->card_name
,
720 THIS_MODULE
, &card
->bt
->dev
->dev
,
723 pr_err("dvb_register_adapter failed (errno = %d)\n", result
);
726 card
->dvb_adapter
.priv
= card
;
728 card
->bt
->adapter
= card
->i2c_adapter
;
730 memset(&card
->demux
, 0, sizeof(struct dvb_demux
));
732 card
->demux
.dmx
.capabilities
= DMX_TS_FILTERING
| DMX_SECTION_FILTERING
| DMX_MEMORY_BASED_FILTERING
;
734 card
->demux
.priv
= card
;
735 card
->demux
.filternum
= 256;
736 card
->demux
.feednum
= 256;
737 card
->demux
.start_feed
= dvb_bt8xx_start_feed
;
738 card
->demux
.stop_feed
= dvb_bt8xx_stop_feed
;
739 card
->demux
.write_to_decoder
= NULL
;
741 result
= dvb_dmx_init(&card
->demux
);
743 pr_err("dvb_dmx_init failed (errno = %d)\n", result
);
744 goto err_unregister_adaptor
;
747 card
->dmxdev
.filternum
= 256;
748 card
->dmxdev
.demux
= &card
->demux
.dmx
;
749 card
->dmxdev
.capabilities
= 0;
751 result
= dvb_dmxdev_init(&card
->dmxdev
, &card
->dvb_adapter
);
753 pr_err("dvb_dmxdev_init failed (errno = %d)\n", result
);
754 goto err_dmx_release
;
757 card
->fe_hw
.source
= DMX_FRONTEND_0
;
759 result
= card
->demux
.dmx
.add_frontend(&card
->demux
.dmx
, &card
->fe_hw
);
761 pr_err("dvb_dmx_init failed (errno = %d)\n", result
);
762 goto err_dmxdev_release
;
765 card
->fe_mem
.source
= DMX_MEMORY_FE
;
767 result
= card
->demux
.dmx
.add_frontend(&card
->demux
.dmx
, &card
->fe_mem
);
769 pr_err("dvb_dmx_init failed (errno = %d)\n", result
);
770 goto err_remove_hw_frontend
;
773 result
= card
->demux
.dmx
.connect_frontend(&card
->demux
.dmx
, &card
->fe_hw
);
775 pr_err("dvb_dmx_init failed (errno = %d)\n", result
);
776 goto err_remove_mem_frontend
;
779 result
= dvb_net_init(&card
->dvb_adapter
, &card
->dvbnet
, &card
->demux
.dmx
);
781 pr_err("dvb_net_init failed (errno = %d)\n", result
);
782 goto err_disconnect_frontend
;
785 INIT_WORK(&card
->bt
->bh_work
, dvb_bt8xx_work
);
787 frontend_init(card
, type
);
791 err_disconnect_frontend
:
792 card
->demux
.dmx
.disconnect_frontend(&card
->demux
.dmx
);
793 err_remove_mem_frontend
:
794 card
->demux
.dmx
.remove_frontend(&card
->demux
.dmx
, &card
->fe_mem
);
795 err_remove_hw_frontend
:
796 card
->demux
.dmx
.remove_frontend(&card
->demux
.dmx
, &card
->fe_hw
);
798 dvb_dmxdev_release(&card
->dmxdev
);
800 dvb_dmx_release(&card
->demux
);
801 err_unregister_adaptor
:
802 dvb_unregister_adapter(&card
->dvb_adapter
);
806 static int dvb_bt8xx_probe(struct bttv_sub_device
*sub
)
808 struct dvb_bt8xx_card
*card
;
809 struct pci_dev
* bttv_pci_dev
;
812 if (!(card
= kzalloc(sizeof(struct dvb_bt8xx_card
), GFP_KERNEL
)))
815 mutex_init(&card
->lock
);
816 card
->bttv_nr
= sub
->core
->nr
;
817 strscpy(card
->card_name
, sub
->core
->v4l2_dev
.name
,
818 sizeof(card
->card_name
));
819 card
->i2c_adapter
= &sub
->core
->i2c_adap
;
821 switch(sub
->core
->type
) {
822 case BTTV_BOARD_PINNACLESAT
:
823 card
->gpio_mode
= 0x0400c060;
824 /* should be: BT878_A_GAIN=0,BT878_A_PWRDN,BT878_DA_DPM,BT878_DA_SBR,
825 BT878_DA_IOM=1,BT878_DA_APP to enable serial highspeed mode. */
826 card
->op_sync_orin
= BT878_RISC_SYNC_MASK
;
827 card
->irq_err_ignore
= BT878_AFBUS
| BT878_AFDSR
;
830 case BTTV_BOARD_DVICO_DVBT_LITE
:
831 card
->gpio_mode
= 0x0400C060;
832 card
->op_sync_orin
= BT878_RISC_SYNC_MASK
;
833 card
->irq_err_ignore
= BT878_AFBUS
| BT878_AFDSR
;
835 * A_PWRDN DA_DPM DA_SBR DA_IOM_DA
836 * DA_APP(parallel) */
839 case BTTV_BOARD_DVICO_FUSIONHDTV_5_LITE
:
840 card
->gpio_mode
= 0x0400c060;
841 card
->op_sync_orin
= BT878_RISC_SYNC_MASK
;
842 card
->irq_err_ignore
= BT878_AFBUS
| BT878_AFDSR
;
845 case BTTV_BOARD_NEBULA_DIGITV
:
846 case BTTV_BOARD_AVDVBT_761
:
847 card
->gpio_mode
= (1 << 26) | (1 << 14) | (1 << 5);
848 card
->op_sync_orin
= BT878_RISC_SYNC_MASK
;
849 card
->irq_err_ignore
= BT878_AFBUS
| BT878_AFDSR
;
850 /* A_PWRDN DA_SBR DA_APP (high speed serial) */
853 case BTTV_BOARD_AVDVBT_771
: //case 0x07711461:
854 card
->gpio_mode
= 0x0400402B;
855 card
->op_sync_orin
= BT878_RISC_SYNC_MASK
;
856 card
->irq_err_ignore
= BT878_AFBUS
| BT878_AFDSR
;
857 /* A_PWRDN DA_SBR DA_APP[0] PKTP=10 RISC_ENABLE FIFO_ENABLE*/
860 case BTTV_BOARD_TWINHAN_DST
:
861 card
->gpio_mode
= 0x2204f2c;
862 card
->op_sync_orin
= BT878_RISC_SYNC_MASK
;
863 card
->irq_err_ignore
= BT878_APABORT
| BT878_ARIPERR
|
864 BT878_APPERR
| BT878_AFBUS
;
865 /* 25,21,14,11,10,9,8,3,2 then
867 * A_SEL=SML, DA_MLB, DA_SBR,
868 * DA_SDR=f, fifo trigger = 32 DWORDS
869 * IOM = 0 == audio A/D
870 * DPM = 0 == digital audio mode
871 * == async data parallel port
872 * then 0x33 (13 is set by start_capture)
873 * DA_APP = async data parallel port,
875 * RISC+FIFO ENABLE */
878 case BTTV_BOARD_PC_HDTV
:
879 card
->gpio_mode
= 0x0100EC7B;
880 card
->op_sync_orin
= BT878_RISC_SYNC_MASK
;
881 card
->irq_err_ignore
= BT878_AFBUS
| BT878_AFDSR
;
885 pr_err("Unknown bttv card type: %d\n", sub
->core
->type
);
890 dprintk("dvb_bt8xx: identified card%d as %s\n", card
->bttv_nr
, card
->card_name
);
892 if (!(bttv_pci_dev
= bttv_get_pcidev(card
->bttv_nr
))) {
893 pr_err("no pci device for card %d\n", card
->bttv_nr
);
898 if (!(card
->bt
= dvb_bt8xx_878_match(card
->bttv_nr
, bttv_pci_dev
))) {
899 pr_err("unable to determine DMA core of card %d,\n", card
->bttv_nr
);
900 pr_err("if you have the ALSA bt87x audio driver installed, try removing it.\n");
906 mutex_init(&card
->bt
->gpio_lock
);
907 card
->bt
->bttv_nr
= sub
->core
->nr
;
909 if ( (ret
= dvb_bt8xx_load_card(card
, sub
->core
->type
)) ) {
914 dev_set_drvdata(&sub
->dev
, card
);
918 static void dvb_bt8xx_remove(struct bttv_sub_device
*sub
)
920 struct dvb_bt8xx_card
*card
= dev_get_drvdata(&sub
->dev
);
922 dprintk("dvb_bt8xx: unloading card%d\n", card
->bttv_nr
);
924 bt878_stop(card
->bt
);
925 cancel_work_sync(&card
->bt
->bh_work
);
926 dvb_net_release(&card
->dvbnet
);
927 card
->demux
.dmx
.remove_frontend(&card
->demux
.dmx
, &card
->fe_mem
);
928 card
->demux
.dmx
.remove_frontend(&card
->demux
.dmx
, &card
->fe_hw
);
929 dvb_dmxdev_release(&card
->dmxdev
);
930 dvb_dmx_release(&card
->demux
);
932 dvb_unregister_frontend(card
->fe
);
933 dvb_frontend_detach(card
->fe
);
935 dvb_unregister_adapter(&card
->dvb_adapter
);
940 static struct bttv_sub_driver driver
= {
944 .probe
= dvb_bt8xx_probe
,
945 .remove
= dvb_bt8xx_remove
,
947 * .shutdown = dvb_bt8xx_shutdown,
948 * .suspend = dvb_bt8xx_suspend,
949 * .resume = dvb_bt8xx_resume,
953 static int __init
dvb_bt8xx_init(void)
955 return bttv_sub_register(&driver
, "dvb");
958 static void __exit
dvb_bt8xx_exit(void)
960 bttv_sub_unregister(&driver
);
963 module_init(dvb_bt8xx_init
);
964 module_exit(dvb_bt8xx_exit
);
966 MODULE_DESCRIPTION("Bt8xx based DVB adapter driver");
967 MODULE_AUTHOR("Florian Schirmer <jolt@tuxbox.org>");
968 MODULE_LICENSE("GPL");