drivers/media/pci/cx18/cx18-dvb.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  *  cx18 functions for DVB support
   4  *
   5  *  Copyright (c) 2008 Steven Toth <stoth@linuxtv.org>
   6  *  Copyright (C) 2008  Andy Walls <awalls@md.metrocast.net>
   7  */
   8
   9 #include "cx18-version.h"
  10 #include "cx18-dvb.h"
  11 #include "cx18-io.h"
  12 #include "cx18-queue.h"
  13 #include "cx18-streams.h"
  14 #include "cx18-cards.h"
  15 #include "cx18-gpio.h"
  16 #include "s5h1409.h"
  17 #include "mxl5005s.h"
  18 #include "s5h1411.h"
  19 #include "tda18271.h"
  20 #include "zl10353.h"
  21
  22 #include <linux/firmware.h>
  23 #include "mt352.h"
  24 #include "mt352_priv.h"
  25 #include "xc2028.h"
  26
  27 DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
  28
  29 #define FWFILE "dvb-cx18-mpc718-mt352.fw"
  30
  31 #define CX18_REG_DMUX_NUM_PORT_0_CONTROL 0xd5a000
  32 #define CX18_CLOCK_ENABLE2               0xc71024
  33 #define CX18_DMUX_CLK_MASK               0x0080
  34
  35 /*
  36  * CX18_CARD_HVR_1600_ESMT
  37  * CX18_CARD_HVR_1600_SAMSUNG
  38  */
  39
  40 static struct mxl5005s_config hauppauge_hvr1600_tuner = {
  41         .i2c_address     = 0xC6 >> 1,
  42         .if_freq         = IF_FREQ_5380000HZ,
  43         .xtal_freq       = CRYSTAL_FREQ_16000000HZ,
  44         .agc_mode        = MXL_SINGLE_AGC,
  45         .tracking_filter = MXL_TF_C_H,
  46         .rssi_enable     = MXL_RSSI_ENABLE,
  47         .cap_select      = MXL_CAP_SEL_ENABLE,
  48         .div_out         = MXL_DIV_OUT_4,
  49         .clock_out       = MXL_CLOCK_OUT_DISABLE,
  50         .output_load     = MXL5005S_IF_OUTPUT_LOAD_200_OHM,
  51         .top             = MXL5005S_TOP_25P2,
  52         .mod_mode        = MXL_DIGITAL_MODE,
  53         .if_mode         = MXL_ZERO_IF,
  54         .qam_gain        = 0x02,
  55         .AgcMasterByte   = 0x00,
  56 };
  57
  58 static struct s5h1409_config hauppauge_hvr1600_config = {
  59         .demod_address = 0x32 >> 1,
  60         .output_mode   = S5H1409_SERIAL_OUTPUT,
  61         .gpio          = S5H1409_GPIO_ON,
  62         .qam_if        = 44000,
  63         .inversion     = S5H1409_INVERSION_OFF,
  64         .status_mode   = S5H1409_DEMODLOCKING,
  65         .mpeg_timing   = S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,
  66         .hvr1600_opt   = S5H1409_HVR1600_OPTIMIZE
  67 };
  68
  69 /*
  70  * CX18_CARD_HVR_1600_S5H1411
  71  */
  72 static struct s5h1411_config hcw_s5h1411_config = {
  73         .output_mode   = S5H1411_SERIAL_OUTPUT,
  74         .gpio          = S5H1411_GPIO_OFF,
  75         .vsb_if        = S5H1411_IF_44000,
  76         .qam_if        = S5H1411_IF_4000,
  77         .inversion     = S5H1411_INVERSION_ON,
  78         .status_mode   = S5H1411_DEMODLOCKING,
  79         .mpeg_timing   = S5H1411_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,
  80 };
  81
  82 static struct tda18271_std_map hauppauge_tda18271_std_map = {
  83         .atsc_6   = { .if_freq = 5380, .agc_mode = 3, .std = 3,
  84                       .if_lvl = 6, .rfagc_top = 0x37 },
  85         .qam_6    = { .if_freq = 4000, .agc_mode = 3, .std = 0,
  86                       .if_lvl = 6, .rfagc_top = 0x37 },
  87 };
  88
  89 static struct tda18271_config hauppauge_tda18271_config = {
  90         .std_map = &hauppauge_tda18271_std_map,
  91         .gate    = TDA18271_GATE_DIGITAL,
  92         .output_opt = TDA18271_OUTPUT_LT_OFF,
  93 };
  94
  95 /*
  96  * CX18_CARD_LEADTEK_DVR3100H
  97  */
  98 /* Information/confirmation of proper config values provided by Terry Wu */
  99 static struct zl10353_config leadtek_dvr3100h_demod = {
 100         .demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
 101         .if2                   = 45600,     /* 4.560 MHz IF from the XC3028 */
 102         .parallel_ts           = 1,         /* Not a serial TS */
 103         .no_tuner              = 1,         /* XC3028 is not behind the gate */
 104         .disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
 105 };
 106
 107 /*
 108  * CX18_CARD_YUAN_MPC718
 109  */
 110 /*
 111  * Due to
 112  *
 113  * 1. an absence of information on how to program the MT352
 114  * 2. the Linux mt352 module pushing MT352 initialization off onto us here
 115  *
 116  * We have to use an init sequence that *you* must extract from the Windows
 117  * driver (yuanrap.sys) and which we load as a firmware.
 118  *
 119  * If someone can provide me with a Zarlink MT352 (Intel CE6352?) Design Manual
 120  * with chip programming details, then I can remove this annoyance.
 121  */
 122 static int yuan_mpc718_mt352_reqfw(struct cx18_stream *stream,
 123                                    const struct firmware **fw)
 124 {
 125         struct cx18 *cx = stream->cx;
 126         const char *fn = FWFILE;
 127         int ret;
 128
 129         ret = request_firmware(fw, fn, &cx->pci_dev->dev);
 130         if (ret)
 131                 CX18_ERR("Unable to open firmware file %s\n", fn);
 132         else {
 133                 size_t sz = (*fw)->size;
 134                 if (sz < 2 || sz > 64 || (sz % 2) != 0) {
 135                         CX18_ERR("Firmware %s has a bad size: %lu bytes\n",
 136                                  fn, (unsigned long) sz);
 137                         ret = -EILSEQ;
 138                         release_firmware(*fw);
 139                         *fw = NULL;
 140                 }
 141         }
 142
 143         if (ret) {
 144                 CX18_ERR("The MPC718 board variant with the MT352 DVB-T demodulator will not work without it\n");
 145                 CX18_ERR("Run 'linux/scripts/get_dvb_firmware mpc718' if you need the firmware\n");
 146         }
 147         return ret;
 148 }
 149
 150 static int yuan_mpc718_mt352_init(struct dvb_frontend *fe)
 151 {
 152         struct cx18_dvb *dvb = container_of(fe->dvb,
 153                                             struct cx18_dvb, dvb_adapter);
 154         struct cx18_stream *stream = dvb->stream;
 155         const struct firmware *fw = NULL;
 156         int ret;
 157         int i;
 158         u8 buf[3];
 159
 160         ret = yuan_mpc718_mt352_reqfw(stream, &fw);
 161         if (ret)
 162                 return ret;
 163
 164         /* Loop through all the register-value pairs in the firmware file */
 165         for (i = 0; i < fw->size; i += 2) {
 166                 buf[0] = fw->data[i];
 167                 /* Intercept a few registers we want to set ourselves */
 168                 switch (buf[0]) {
 169                 case TRL_NOMINAL_RATE_0:
 170                         /* Set our custom OFDM bandwidth in the case below */
 171                         break;
 172                 case TRL_NOMINAL_RATE_1:
 173                         /* 6 MHz: 64/7 * 6/8 / 20.48 * 2^16 = 0x55b6.db6 */
 174                         /* 7 MHz: 64/7 * 7/8 / 20.48 * 2^16 = 0x6400 */
 175                         /* 8 MHz: 64/7 * 8/8 / 20.48 * 2^16 = 0x7249.249 */
 176                         buf[1] = 0x72;
 177                         buf[2] = 0x49;
 178                         mt352_write(fe, buf, 3);
 179                         break;
 180                 case INPUT_FREQ_0:
 181                         /* Set our custom IF in the case below */
 182                         break;
 183                 case INPUT_FREQ_1:
 184                         /* 4.56 MHz IF: (20.48 - 4.56)/20.48 * 2^14 = 0x31c0 */
 185                         buf[1] = 0x31;
 186                         buf[2] = 0xc0;
 187                         mt352_write(fe, buf, 3);
 188                         break;
 189                 default:
 190                         /* Pass through the register-value pair from the fw */
 191                         buf[1] = fw->data[i+1];
 192                         mt352_write(fe, buf, 2);
 193                         break;
 194                 }
 195         }
 196
 197         buf[0] = (u8) TUNER_GO;
 198         buf[1] = 0x01; /* Go */
 199         mt352_write(fe, buf, 2);
 200         release_firmware(fw);
 201         return 0;
 202 }
 203
 204 static struct mt352_config yuan_mpc718_mt352_demod = {
 205         .demod_address = 0x1e >> 1,
 206         .adc_clock     = 20480,     /* 20.480 MHz */
 207         .if2           =  4560,     /*  4.560 MHz */
 208         .no_tuner      = 1,         /* XC3028 is not behind the gate */
 209         .demod_init    = yuan_mpc718_mt352_init,
 210 };
 211
 212 static struct zl10353_config yuan_mpc718_zl10353_demod = {
 213         .demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
 214         .if2                   = 45600,     /* 4.560 MHz IF from the XC3028 */
 215         .parallel_ts           = 1,         /* Not a serial TS */
 216         .no_tuner              = 1,         /* XC3028 is not behind the gate */
 217         .disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
 218 };
 219
 220 static struct zl10353_config gotview_dvd3_zl10353_demod = {
 221         .demod_address         = 0x1e >> 1, /* Datasheet suggested straps */
 222         .if2                   = 45600,     /* 4.560 MHz IF from the XC3028 */
 223         .parallel_ts           = 1,         /* Not a serial TS */
 224         .no_tuner              = 1,         /* XC3028 is not behind the gate */
 225         .disable_i2c_gate_ctrl = 1,         /* Disable the I2C gate */
 226 };
 227
 228 static int dvb_register(struct cx18_stream *stream);
 229
 230 /* Kernel DVB framework calls this when the feed needs to start.
 231  * The CX18 framework should enable the transport DMA handling
 232  * and queue processing.
 233  */
 234 static int cx18_dvb_start_feed(struct dvb_demux_feed *feed)
 235 {
 236         struct dvb_demux *demux = feed->demux;
 237         struct cx18_stream *stream = demux->priv;
 238         struct cx18 *cx;
 239         int ret;
 240         u32 v;
 241
 242         if (!stream)
 243                 return -EINVAL;
 244
 245         cx = stream->cx;
 246         CX18_DEBUG_INFO("Start feed: pid = 0x%x index = %d\n",
 247                         feed->pid, feed->index);
 248
 249         mutex_lock(&cx->serialize_lock);
 250         ret = cx18_init_on_first_open(cx);
 251         mutex_unlock(&cx->serialize_lock);
 252         if (ret) {
 253                 CX18_ERR("Failed to initialize firmware starting DVB feed\n");
 254                 return ret;
 255         }
 256         ret = -EINVAL;
 257
 258         switch (cx->card->type) {
 259         case CX18_CARD_HVR_1600_ESMT:
 260         case CX18_CARD_HVR_1600_SAMSUNG:
 261         case CX18_CARD_HVR_1600_S5H1411:
 262                 v = cx18_read_reg(cx, CX18_REG_DMUX_NUM_PORT_0_CONTROL);
 263                 v |= 0x00400000; /* Serial Mode */
 264                 v |= 0x00002000; /* Data Length - Byte */
 265                 v |= 0x00010000; /* Error - Polarity */
 266                 v |= 0x00020000; /* Error - Passthru */
 267                 v |= 0x000c0000; /* Error - Ignore */
 268                 cx18_write_reg(cx, v, CX18_REG_DMUX_NUM_PORT_0_CONTROL);
 269                 break;
 270
 271         case CX18_CARD_LEADTEK_DVR3100H:
 272         case CX18_CARD_YUAN_MPC718:
 273         case CX18_CARD_GOTVIEW_PCI_DVD3:
 274         default:
 275                 /* Assumption - Parallel transport - Signalling
 276                  * undefined or default.
 277                  */
 278                 break;
 279         }
 280
 281         if (!demux->dmx.frontend)
 282                 return -EINVAL;
 283
 284         mutex_lock(&stream->dvb->feedlock);
 285         if (stream->dvb->feeding++ == 0) {
 286                 CX18_DEBUG_INFO("Starting Transport DMA\n");
 287                 mutex_lock(&cx->serialize_lock);
 288                 set_bit(CX18_F_S_STREAMING, &stream->s_flags);
 289                 ret = cx18_start_v4l2_encode_stream(stream);
 290                 if (ret < 0) {
 291                         CX18_DEBUG_INFO("Failed to start Transport DMA\n");
 292                         stream->dvb->feeding--;
 293                         if (stream->dvb->feeding == 0)
 294                                 clear_bit(CX18_F_S_STREAMING, &stream->s_flags);
 295                 }
 296                 mutex_unlock(&cx->serialize_lock);
 297         } else
 298                 ret = 0;
 299         mutex_unlock(&stream->dvb->feedlock);
 300
 301         return ret;
 302 }
 303
 304 /* Kernel DVB framework calls this when the feed needs to stop. */
 305 static int cx18_dvb_stop_feed(struct dvb_demux_feed *feed)
 306 {
 307         struct dvb_demux *demux = feed->demux;
 308         struct cx18_stream *stream = demux->priv;
 309         struct cx18 *cx;
 310         int ret = -EINVAL;
 311
 312         if (stream) {
 313                 cx = stream->cx;
 314                 CX18_DEBUG_INFO("Stop feed: pid = 0x%x index = %d\n",
 315                                 feed->pid, feed->index);
 316
 317                 mutex_lock(&stream->dvb->feedlock);
 318                 if (--stream->dvb->feeding == 0) {
 319                         CX18_DEBUG_INFO("Stopping Transport DMA\n");
 320                         mutex_lock(&cx->serialize_lock);
 321                         ret = cx18_stop_v4l2_encode_stream(stream, 0);
 322                         mutex_unlock(&cx->serialize_lock);
 323                 } else
 324                         ret = 0;
 325                 mutex_unlock(&stream->dvb->feedlock);
 326         }
 327
 328         return ret;
 329 }
 330
 331 int cx18_dvb_register(struct cx18_stream *stream)
 332 {
 333         struct cx18 *cx = stream->cx;
 334         struct cx18_dvb *dvb = stream->dvb;
 335         struct dvb_adapter *dvb_adapter;
 336         struct dvb_demux *dvbdemux;
 337         struct dmx_demux *dmx;
 338         int ret;
 339
 340         if (!dvb)
 341                 return -EINVAL;
 342
 343         dvb->enabled = 0;
 344         dvb->stream = stream;
 345
 346         ret = dvb_register_adapter(&dvb->dvb_adapter,
 347                         CX18_DRIVER_NAME,
 348                         THIS_MODULE, &cx->pci_dev->dev, adapter_nr);
 349         if (ret < 0)
 350                 goto err_out;
 351
 352         dvb_adapter = &dvb->dvb_adapter;
 353
 354         dvbdemux = &dvb->demux;
 355
 356         dvbdemux->priv = (void *)stream;
 357
 358         dvbdemux->filternum = 256;
 359         dvbdemux->feednum = 256;
 360         dvbdemux->start_feed = cx18_dvb_start_feed;
 361         dvbdemux->stop_feed = cx18_dvb_stop_feed;
 362         dvbdemux->dmx.capabilities = (DMX_TS_FILTERING |
 363                 DMX_SECTION_FILTERING | DMX_MEMORY_BASED_FILTERING);
 364         ret = dvb_dmx_init(dvbdemux);
 365         if (ret < 0)
 366                 goto err_dvb_unregister_adapter;
 367
 368         dmx = &dvbdemux->dmx;
 369
 370         dvb->hw_frontend.source = DMX_FRONTEND_0;
 371         dvb->mem_frontend.source = DMX_MEMORY_FE;
 372         dvb->dmxdev.filternum = 256;
 373         dvb->dmxdev.demux = dmx;
 374
 375         ret = dvb_dmxdev_init(&dvb->dmxdev, dvb_adapter);
 376         if (ret < 0)
 377                 goto err_dvb_dmx_release;
 378
 379         ret = dmx->add_frontend(dmx, &dvb->hw_frontend);
 380         if (ret < 0)
 381                 goto err_dvb_dmxdev_release;
 382
 383         ret = dmx->add_frontend(dmx, &dvb->mem_frontend);
 384         if (ret < 0)
 385                 goto err_remove_hw_frontend;
 386
 387         ret = dmx->connect_frontend(dmx, &dvb->hw_frontend);
 388         if (ret < 0)
 389                 goto err_remove_mem_frontend;
 390
 391         ret = dvb_register(stream);
 392         if (ret < 0)
 393                 goto err_disconnect_frontend;
 394
 395         dvb_net_init(dvb_adapter, &dvb->dvbnet, dmx);
 396
 397         CX18_INFO("DVB Frontend registered\n");
 398         CX18_INFO("Registered DVB adapter%d for %s (%d x %d.%02d kB)\n",
 399                   stream->dvb->dvb_adapter.num, stream->name,
 400                   stream->buffers, stream->buf_size/1024,
 401                   (stream->buf_size * 100 / 1024) % 100);
 402
 403         mutex_init(&dvb->feedlock);
 404         dvb->enabled = 1;
 405         return ret;
 406
 407 err_disconnect_frontend:
 408         dmx->disconnect_frontend(dmx);
 409 err_remove_mem_frontend:
 410         dmx->remove_frontend(dmx, &dvb->mem_frontend);
 411 err_remove_hw_frontend:
 412         dmx->remove_frontend(dmx, &dvb->hw_frontend);
 413 err_dvb_dmxdev_release:
 414         dvb_dmxdev_release(&dvb->dmxdev);
 415 err_dvb_dmx_release:
 416         dvb_dmx_release(dvbdemux);
 417 err_dvb_unregister_adapter:
 418         dvb_unregister_adapter(dvb_adapter);
 419 err_out:
 420         return ret;
 421 }
 422
 423 void cx18_dvb_unregister(struct cx18_stream *stream)
 424 {
 425         struct cx18 *cx = stream->cx;
 426         struct cx18_dvb *dvb = stream->dvb;
 427         struct dvb_adapter *dvb_adapter;
 428         struct dvb_demux *dvbdemux;
 429         struct dmx_demux *dmx;
 430
 431         CX18_INFO("unregister DVB\n");
 432
 433         if (dvb == NULL || !dvb->enabled)
 434                 return;
 435
 436         dvb_adapter = &dvb->dvb_adapter;
 437         dvbdemux = &dvb->demux;
 438         dmx = &dvbdemux->dmx;
 439
 440         dmx->close(dmx);
 441         dvb_net_release(&dvb->dvbnet);
 442         dmx->remove_frontend(dmx, &dvb->mem_frontend);
 443         dmx->remove_frontend(dmx, &dvb->hw_frontend);
 444         dvb_dmxdev_release(&dvb->dmxdev);
 445         dvb_dmx_release(dvbdemux);
 446         dvb_unregister_frontend(dvb->fe);
 447         dvb_frontend_detach(dvb->fe);
 448         dvb_unregister_adapter(dvb_adapter);
 449 }
 450
 451 /* All the DVB attach calls go here, this function gets modified
 452  * for each new card. cx18_dvb_start_feed() will also need changes.
 453  */
 454 static int dvb_register(struct cx18_stream *stream)
 455 {
 456         struct cx18_dvb *dvb = stream->dvb;
 457         struct cx18 *cx = stream->cx;
 458         int ret = 0;
 459
 460         switch (cx->card->type) {
 461         case CX18_CARD_HVR_1600_ESMT:
 462         case CX18_CARD_HVR_1600_SAMSUNG:
 463                 dvb->fe = dvb_attach(s5h1409_attach,
 464                         &hauppauge_hvr1600_config,
 465                         &cx->i2c_adap[0]);
 466                 if (dvb->fe != NULL) {
 467                         dvb_attach(mxl5005s_attach, dvb->fe,
 468                                 &cx->i2c_adap[0],
 469                                 &hauppauge_hvr1600_tuner);
 470                         ret = 0;
 471                 }
 472                 break;
 473         case CX18_CARD_HVR_1600_S5H1411:
 474                 dvb->fe = dvb_attach(s5h1411_attach,
 475                                      &hcw_s5h1411_config,
 476                                      &cx->i2c_adap[0]);
 477                 if (dvb->fe != NULL)
 478                         dvb_attach(tda18271_attach, dvb->fe,
 479                                    0x60, &cx->i2c_adap[0],
 480                                    &hauppauge_tda18271_config);
 481                 break;
 482         case CX18_CARD_LEADTEK_DVR3100H:
 483                 dvb->fe = dvb_attach(zl10353_attach,
 484                                      &leadtek_dvr3100h_demod,
 485                                      &cx->i2c_adap[1]);
 486                 if (dvb->fe != NULL) {
 487                         struct dvb_frontend *fe;
 488                         struct xc2028_config cfg = {
 489                                 .i2c_adap = &cx->i2c_adap[1],
 490                                 .i2c_addr = 0xc2 >> 1,
 491                                 .ctrl = NULL,
 492                         };
 493                         static struct xc2028_ctrl ctrl = {
 494                                 .fname   = XC2028_DEFAULT_FIRMWARE,
 495                                 .max_len = 64,
 496                                 .demod   = XC3028_FE_ZARLINK456,
 497                                 .type    = XC2028_AUTO,
 498                         };
 499
 500                         fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
 501                         if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
 502                                 fe->ops.tuner_ops.set_config(fe, &ctrl);
 503                 }
 504                 break;
 505         case CX18_CARD_YUAN_MPC718:
 506                 /*
 507                  * TODO
 508                  * Apparently, these cards also could instead have a
 509                  * DiBcom demod supported by one of the db7000 drivers
 510                  */
 511                 dvb->fe = dvb_attach(mt352_attach,
 512                                      &yuan_mpc718_mt352_demod,
 513                                      &cx->i2c_adap[1]);
 514                 if (dvb->fe == NULL)
 515                         dvb->fe = dvb_attach(zl10353_attach,
 516                                              &yuan_mpc718_zl10353_demod,
 517                                              &cx->i2c_adap[1]);
 518                 if (dvb->fe != NULL) {
 519                         struct dvb_frontend *fe;
 520                         struct xc2028_config cfg = {
 521                                 .i2c_adap = &cx->i2c_adap[1],
 522                                 .i2c_addr = 0xc2 >> 1,
 523                                 .ctrl = NULL,
 524                         };
 525                         static struct xc2028_ctrl ctrl = {
 526                                 .fname   = XC2028_DEFAULT_FIRMWARE,
 527                                 .max_len = 64,
 528                                 .demod   = XC3028_FE_ZARLINK456,
 529                                 .type    = XC2028_AUTO,
 530                         };
 531
 532                         fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
 533                         if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
 534                                 fe->ops.tuner_ops.set_config(fe, &ctrl);
 535                 }
 536                 break;
 537         case CX18_CARD_GOTVIEW_PCI_DVD3:
 538                         dvb->fe = dvb_attach(zl10353_attach,
 539                                              &gotview_dvd3_zl10353_demod,
 540                                              &cx->i2c_adap[1]);
 541                 if (dvb->fe != NULL) {
 542                         struct dvb_frontend *fe;
 543                         struct xc2028_config cfg = {
 544                                 .i2c_adap = &cx->i2c_adap[1],
 545                                 .i2c_addr = 0xc2 >> 1,
 546                                 .ctrl = NULL,
 547                         };
 548                         static struct xc2028_ctrl ctrl = {
 549                                 .fname   = XC2028_DEFAULT_FIRMWARE,
 550                                 .max_len = 64,
 551                                 .demod   = XC3028_FE_ZARLINK456,
 552                                 .type    = XC2028_AUTO,
 553                         };
 554
 555                         fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
 556                         if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
 557                                 fe->ops.tuner_ops.set_config(fe, &ctrl);
 558                 }
 559                 break;
 560         default:
 561                 /* No Digital Tv Support */
 562                 break;
 563         }
 564
 565         if (dvb->fe == NULL) {
 566                 CX18_ERR("frontend initialization failed\n");
 567                 return -1;
 568         }
 569
 570         dvb->fe->callback = cx18_reset_tuner_gpio;
 571
 572         ret = dvb_register_frontend(&dvb->dvb_adapter, dvb->fe);
 573         if (ret < 0) {
 574                 if (dvb->fe->ops.release)
 575                         dvb->fe->ops.release(dvb->fe);
 576                 return ret;
 577         }
 578
 579         /*
 580          * The firmware seems to enable the TS DMUX clock
 581          * under various circumstances.  However, since we know we
 582          * might use it, let's just turn it on ourselves here.
 583          */
 584         cx18_write_reg_expect(cx,
 585                               (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK,
 586                               CX18_CLOCK_ENABLE2,
 587                               CX18_DMUX_CLK_MASK,
 588                               (CX18_DMUX_CLK_MASK << 16) | CX18_DMUX_CLK_MASK);
 589
 590         return ret;
 591 }
 592
 593 MODULE_FIRMWARE(FWFILE);