drivers/media/usb/au0828/au0828-cards.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  *  Driver for the Auvitek USB bridge
   4  *
   5  *  Copyright (c) 2008 Steven Toth <stoth@linuxtv.org>
   6  */
   7
   8 #include "au0828.h"
   9 #include "au0828-cards.h"
  10 #include "au8522.h"
  11 #include "media/tuner.h"
  12 #include "media/v4l2-common.h"
  13
  14 static void hvr950q_cs5340_audio(void *priv, int enable)
  15 {
  16         /* Because the HVR-950q shares an i2s bus between the cs5340 and the
  17            au8522, we need to hold cs5340 in reset when using the au8522 */
  18         struct au0828_dev *dev = priv;
  19         if (enable == 1)
  20                 au0828_set(dev, REG_000, 0x10);
  21         else
  22                 au0828_clear(dev, REG_000, 0x10);
  23 }
  24
  25 /*
  26  * WARNING: There's a quirks table at sound/usb/quirks-table.h
  27  * that should also be updated every time a new device with V4L2 support
  28  * is added here.
  29  */
  30 struct au0828_board au0828_boards[] = {
  31         [AU0828_BOARD_UNKNOWN] = {
  32                 .name   = "Unknown board",
  33                 .tuner_type = -1U,
  34                 .tuner_addr = ADDR_UNSET,
  35         },
  36         [AU0828_BOARD_HAUPPAUGE_HVR850] = {
  37                 .name   = "Hauppauge HVR850",
  38                 .tuner_type = TUNER_XC5000,
  39                 .tuner_addr = 0x61,
  40                 .has_ir_i2c = 1,
  41                 .has_analog = 1,
  42                 .i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
  43                 .input = {
  44                         {
  45                                 .type = AU0828_VMUX_TELEVISION,
  46                                 .vmux = AU8522_COMPOSITE_CH4_SIF,
  47                                 .amux = AU8522_AUDIO_SIF,
  48                         },
  49                         {
  50                                 .type = AU0828_VMUX_COMPOSITE,
  51                                 .vmux = AU8522_COMPOSITE_CH1,
  52                                 .amux = AU8522_AUDIO_NONE,
  53                                 .audio_setup = hvr950q_cs5340_audio,
  54                         },
  55                         {
  56                                 .type = AU0828_VMUX_SVIDEO,
  57                                 .vmux = AU8522_SVIDEO_CH13,
  58                                 .amux = AU8522_AUDIO_NONE,
  59                                 .audio_setup = hvr950q_cs5340_audio,
  60                         },
  61                 },
  62         },
  63         [AU0828_BOARD_HAUPPAUGE_HVR950Q] = {
  64                 .name   = "Hauppauge HVR950Q",
  65                 .tuner_type = TUNER_XC5000,
  66                 .tuner_addr = 0x61,
  67                 .has_ir_i2c = 1,
  68                 .has_analog = 1,
  69                 .i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
  70                 .input = {
  71                         {
  72                                 .type = AU0828_VMUX_TELEVISION,
  73                                 .vmux = AU8522_COMPOSITE_CH4_SIF,
  74                                 .amux = AU8522_AUDIO_SIF,
  75                         },
  76                         {
  77                                 .type = AU0828_VMUX_COMPOSITE,
  78                                 .vmux = AU8522_COMPOSITE_CH1,
  79                                 .amux = AU8522_AUDIO_NONE,
  80                                 .audio_setup = hvr950q_cs5340_audio,
  81                         },
  82                         {
  83                                 .type = AU0828_VMUX_SVIDEO,
  84                                 .vmux = AU8522_SVIDEO_CH13,
  85                                 .amux = AU8522_AUDIO_NONE,
  86                                 .audio_setup = hvr950q_cs5340_audio,
  87                         },
  88                 },
  89         },
  90         [AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL] = {
  91                 .name   = "Hauppauge HVR950Q rev xxF8",
  92                 .tuner_type = TUNER_XC5000,
  93                 .tuner_addr = 0x61,
  94                 .i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
  95         },
  96         [AU0828_BOARD_DVICO_FUSIONHDTV7] = {
  97                 .name   = "DViCO FusionHDTV USB",
  98                 .tuner_type = TUNER_XC5000,
  99                 .tuner_addr = 0x61,
 100                 .i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
 101         },
 102         [AU0828_BOARD_HAUPPAUGE_WOODBURY] = {
 103                 .name = "Hauppauge Woodbury",
 104                 .tuner_type = TUNER_NXP_TDA18271,
 105                 .tuner_addr = 0x60,
 106                 .i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
 107         },
 108 };
 109
 110 /* Tuner callback function for au0828 boards. Currently only needed
 111  * for HVR1500Q, which has an xc5000 tuner.
 112  */
 113 int au0828_tuner_callback(void *priv, int component, int command, int arg)
 114 {
 115         struct au0828_dev *dev = priv;
 116
 117         dprintk(1, "%s()\n", __func__);
 118
 119         switch (dev->boardnr) {
 120         case AU0828_BOARD_HAUPPAUGE_HVR850:
 121         case AU0828_BOARD_HAUPPAUGE_HVR950Q:
 122         case AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL:
 123         case AU0828_BOARD_DVICO_FUSIONHDTV7:
 124                 if (command == 0) {
 125                         /* Tuner Reset Command from xc5000 */
 126                         /* Drive the tuner into reset and out */
 127                         au0828_clear(dev, REG_001, 2);
 128                         mdelay(10);
 129                         au0828_set(dev, REG_001, 2);
 130                         mdelay(10);
 131                         return 0;
 132                 } else {
 133                         pr_err("%s(): Unknown command.\n", __func__);
 134                         return -EINVAL;
 135                 }
 136                 break;
 137         }
 138
 139         return 0; /* Should never be here */
 140 }
 141
 142 static void hauppauge_eeprom(struct au0828_dev *dev, u8 *eeprom_data)
 143 {
 144         struct tveeprom tv;
 145
 146         tveeprom_hauppauge_analog(&tv, eeprom_data);
 147         dev->board.tuner_type = tv.tuner_type;
 148
 149         /* Make sure we support the board model */
 150         switch (tv.model) {
 151         case 72000: /* WinTV-HVR950q (Retail, IR, ATSC/QAM */
 152         case 72001: /* WinTV-HVR950q (Retail, IR, ATSC/QAM and analog video */
 153         case 72101: /* WinTV-HVR950q (Retail, IR, ATSC/QAM and analog video */
 154         case 72201: /* WinTV-HVR950q (OEM, IR, ATSC/QAM and analog video */
 155         case 72211: /* WinTV-HVR950q (OEM, IR, ATSC/QAM and analog video */
 156         case 72221: /* WinTV-HVR950q (OEM, IR, ATSC/QAM and analog video */
 157         case 72231: /* WinTV-HVR950q (OEM, IR, ATSC/QAM and analog video */
 158         case 72241: /* WinTV-HVR950q (OEM, No IR, ATSC/QAM and analog video */
 159         case 72251: /* WinTV-HVR950q (Retail, IR, ATSC/QAM and analog video */
 160         case 72261: /* WinTV-HVR950q (OEM, No IR, ATSC/QAM and analog video */
 161         case 72271: /* WinTV-HVR950q (OEM, No IR, ATSC/QAM and analog video */
 162         case 72281: /* WinTV-HVR950q (OEM, No IR, ATSC/QAM and analog video */
 163         case 72301: /* WinTV-HVR850 (Retail, IR, ATSC and analog video */
 164         case 72500: /* WinTV-HVR950q (OEM, No IR, ATSC/QAM */
 165                 break;
 166         default:
 167                 pr_warn("%s: warning: unknown hauppauge model #%d\n",
 168                         __func__, tv.model);
 169                 break;
 170         }
 171
 172         pr_info("%s: hauppauge eeprom: model=%d\n",
 173                __func__, tv.model);
 174 }
 175
 176 void au0828_card_analog_fe_setup(struct au0828_dev *dev);
 177
 178 void au0828_card_setup(struct au0828_dev *dev)
 179 {
 180         static u8 eeprom[256];
 181
 182         dprintk(1, "%s()\n", __func__);
 183
 184         if (dev->i2c_rc == 0) {
 185                 dev->i2c_client.addr = 0xa0 >> 1;
 186                 tveeprom_read(&dev->i2c_client, eeprom, sizeof(eeprom));
 187         }
 188
 189         switch (dev->boardnr) {
 190         case AU0828_BOARD_HAUPPAUGE_HVR850:
 191         case AU0828_BOARD_HAUPPAUGE_HVR950Q:
 192         case AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL:
 193         case AU0828_BOARD_HAUPPAUGE_WOODBURY:
 194                 if (dev->i2c_rc == 0)
 195                         hauppauge_eeprom(dev, eeprom+0xa0);
 196                 break;
 197         }
 198
 199         au0828_card_analog_fe_setup(dev);
 200 }
 201
 202 void au0828_card_analog_fe_setup(struct au0828_dev *dev)
 203 {
 204 #ifdef CONFIG_VIDEO_AU0828_V4L2
 205         struct tuner_setup tun_setup;
 206         struct v4l2_subdev *sd;
 207         unsigned int mode_mask = T_ANALOG_TV;
 208
 209         if (AUVI_INPUT(0).type != AU0828_VMUX_UNDEFINED) {
 210                 /* Load the analog demodulator driver (note this would need to
 211                    be abstracted out if we ever need to support a different
 212                    demod) */
 213                 sd = v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_adap,
 214                                 "au8522", 0x8e >> 1, NULL);
 215                 if (sd == NULL)
 216                         pr_err("analog subdev registration failed\n");
 217         }
 218
 219         /* Setup tuners */
 220         if (dev->board.tuner_type != TUNER_ABSENT && dev->board.has_analog) {
 221                 /* Load the tuner module, which does the attach */
 222                 sd = v4l2_i2c_new_subdev(&dev->v4l2_dev, &dev->i2c_adap,
 223                                 "tuner", dev->board.tuner_addr, NULL);
 224                 if (sd == NULL)
 225                         pr_err("tuner subdev registration fail\n");
 226
 227                 tun_setup.mode_mask      = mode_mask;
 228                 tun_setup.type           = dev->board.tuner_type;
 229                 tun_setup.addr           = dev->board.tuner_addr;
 230                 tun_setup.tuner_callback = au0828_tuner_callback;
 231                 v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_type_addr,
 232                                      &tun_setup);
 233         }
 234 #endif
 235 }
 236
 237 /*
 238  * The bridge has between 8 and 12 gpios.
 239  * Regs 1 and 0 deal with output enables.
 240  * Regs 3 and 2 deal with direction.
 241  */
 242 void au0828_gpio_setup(struct au0828_dev *dev)
 243 {
 244         dprintk(1, "%s()\n", __func__);
 245
 246         switch (dev->boardnr) {
 247         case AU0828_BOARD_HAUPPAUGE_HVR850:
 248         case AU0828_BOARD_HAUPPAUGE_HVR950Q:
 249         case AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL:
 250         case AU0828_BOARD_HAUPPAUGE_WOODBURY:
 251                 /* GPIO's
 252                  * 4 - CS5340
 253                  * 5 - AU8522 Demodulator
 254                  * 6 - eeprom W/P
 255                  * 7 - power supply
 256                  * 9 - XC5000 Tuner
 257                  */
 258
 259                 /* Set relevant GPIOs as outputs (leave the EEPROM W/P
 260                    as an input since we will never touch it and it has
 261                    a pullup) */
 262                 au0828_write(dev, REG_003, 0x02);
 263                 au0828_write(dev, REG_002, 0x80 | 0x20 | 0x10);
 264
 265                 /* Into reset */
 266                 au0828_write(dev, REG_001, 0x0);
 267                 au0828_write(dev, REG_000, 0x0);
 268                 msleep(50);
 269
 270                 /* Bring power supply out of reset */
 271                 au0828_write(dev, REG_000, 0x80);
 272                 msleep(50);
 273
 274                 /* Bring xc5000 and au8522 out of reset (leave the
 275                    cs5340 in reset until needed) */
 276                 au0828_write(dev, REG_001, 0x02); /* xc5000 */
 277                 au0828_write(dev, REG_000, 0x80 | 0x20); /* PS + au8522 */
 278
 279                 msleep(250);
 280                 break;
 281         case AU0828_BOARD_DVICO_FUSIONHDTV7:
 282                 /* GPIO's
 283                  * 6 - ?
 284                  * 8 - AU8522 Demodulator
 285                  * 9 - XC5000 Tuner
 286                  */
 287
 288                 /* Into reset */
 289                 au0828_write(dev, REG_003, 0x02);
 290                 au0828_write(dev, REG_002, 0xa0);
 291                 au0828_write(dev, REG_001, 0x0);
 292                 au0828_write(dev, REG_000, 0x0);
 293                 msleep(100);
 294
 295                 /* Out of reset */
 296                 au0828_write(dev, REG_003, 0x02);
 297                 au0828_write(dev, REG_002, 0xa0);
 298                 au0828_write(dev, REG_001, 0x02);
 299                 au0828_write(dev, REG_000, 0xa0);
 300                 msleep(250);
 301                 break;
 302         }
 303 }
 304
 305 /* table of devices that work with this driver */
 306 struct usb_device_id au0828_usb_id_table[] = {
 307         { USB_DEVICE(0x2040, 0x7200),
 308                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 309         { USB_DEVICE(0x2040, 0x7240),
 310                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR850 },
 311         { USB_DEVICE(0x0fe9, 0xd620),
 312                 .driver_info = AU0828_BOARD_DVICO_FUSIONHDTV7 },
 313         { USB_DEVICE(0x2040, 0x7210),
 314                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 315         { USB_DEVICE(0x2040, 0x7217),
 316                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 317         { USB_DEVICE(0x2040, 0x721b),
 318                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 319         { USB_DEVICE(0x2040, 0x721e),
 320                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 321         { USB_DEVICE(0x2040, 0x721f),
 322                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 323         { USB_DEVICE(0x2040, 0x7280),
 324                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 325         { USB_DEVICE(0x0fd9, 0x0008),
 326                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 327         { USB_DEVICE(0x2040, 0x7201),
 328                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL },
 329         { USB_DEVICE(0x2040, 0x7211),
 330                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL },
 331         { USB_DEVICE(0x2040, 0x7281),
 332                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q_MXL },
 333         { USB_DEVICE(0x05e1, 0x0480),
 334                 .driver_info = AU0828_BOARD_HAUPPAUGE_WOODBURY },
 335         { USB_DEVICE(0x2040, 0x8200),
 336                 .driver_info = AU0828_BOARD_HAUPPAUGE_WOODBURY },
 337         { USB_DEVICE(0x2040, 0x7260),
 338                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 339         { USB_DEVICE(0x2040, 0x7213),
 340                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 341         { USB_DEVICE(0x2040, 0x7270),
 342                 .driver_info = AU0828_BOARD_HAUPPAUGE_HVR950Q },
 343         { },
 344 };
 345
 346 MODULE_DEVICE_TABLE(usb, au0828_usb_id_table);