drm/rockchip: Don't change hdmi reference clock rate

[drm/drm-misc.git] / drivers / net / ethernet / intel / ixgbe / ixgbe_common.c

// SPDX-License-Identifier: GPL-2.0
/* Copyright(c) 1999 - 2018 Intel Corporation. */

#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/sched.h>
#include <linux/netdevice.h>

#include "ixgbe.h"
#include "ixgbe_common.h"
#include "ixgbe_phy.h"

static int ixgbe_acquire_eeprom(struct ixgbe_hw *hw);
static int ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw);
static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw);
static int ixgbe_ready_eeprom(struct ixgbe_hw *hw);
static void ixgbe_standby_eeprom(struct ixgbe_hw *hw);
static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
                                        u16 count);
static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count);
static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
static void ixgbe_release_eeprom(struct ixgbe_hw *hw);

static int ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
static int ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg);
static int ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
                                             u16 words, u16 *data);
static int ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
                                              u16 words, u16 *data);
static int ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
                                                 u16 offset);
static int ixgbe_disable_pcie_primary(struct ixgbe_hw *hw);

/* Base table for registers values that change by MAC */
const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = {
        IXGBE_MVALS_INIT(8259X)
};

/**
 *  ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
 *  control
 *  @hw: pointer to hardware structure
 *
 *  There are several phys that do not support autoneg flow control. This
 *  function check the device id to see if the associated phy supports
 *  autoneg flow control.
 **/
bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
{
        bool supported = false;
        ixgbe_link_speed speed;
        bool link_up;

        switch (hw->phy.media_type) {
        case ixgbe_media_type_fiber:
                /* flow control autoneg black list */
                switch (hw->device_id) {
                case IXGBE_DEV_ID_X550EM_A_SFP:
                case IXGBE_DEV_ID_X550EM_A_SFP_N:
                        supported = false;
                        break;
                default:
                        hw->mac.ops.check_link(hw, &speed, &link_up, false);
                        /* if link is down, assume supported */
                        if (link_up)
                                supported = speed == IXGBE_LINK_SPEED_1GB_FULL;
                        else
                                supported = true;
                }

                break;
        case ixgbe_media_type_backplane:
                if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI)
                        supported = false;
                else
                        supported = true;
                break;
        case ixgbe_media_type_copper:
                /* only some copper devices support flow control autoneg */
                switch (hw->device_id) {
                case IXGBE_DEV_ID_82599_T3_LOM:
                case IXGBE_DEV_ID_X540T:
                case IXGBE_DEV_ID_X540T1:
                case IXGBE_DEV_ID_X550T:
                case IXGBE_DEV_ID_X550T1:
                case IXGBE_DEV_ID_X550EM_X_10G_T:
                case IXGBE_DEV_ID_X550EM_A_10G_T:
                case IXGBE_DEV_ID_X550EM_A_1G_T:
                case IXGBE_DEV_ID_X550EM_A_1G_T_L:
                        supported = true;
                        break;
                default:
                        break;
                }
                break;
        default:
                break;
        }

        if (!supported)
                hw_dbg(hw, "Device %x does not support flow control autoneg\n",
                       hw->device_id);

        return supported;
}

/**
 *  ixgbe_setup_fc_generic - Set up flow control
 *  @hw: pointer to hardware structure
 *
 *  Called at init time to set up flow control.
 **/
int ixgbe_setup_fc_generic(struct ixgbe_hw *hw)
{
        u32 reg = 0, reg_bp = 0;
        bool locked = false;
        int ret_val = 0;
        u16 reg_cu = 0;

        /*
         * Validate the requested mode.  Strict IEEE mode does not allow
         * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
         */
        if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
                hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
                return -EINVAL;
        }

        /*
         * 10gig parts do not have a word in the EEPROM to determine the
         * default flow control setting, so we explicitly set it to full.
         */
        if (hw->fc.requested_mode == ixgbe_fc_default)
                hw->fc.requested_mode = ixgbe_fc_full;

        /*
         * Set up the 1G and 10G flow control advertisement registers so the
         * HW will be able to do fc autoneg once the cable is plugged in.  If
         * we link at 10G, the 1G advertisement is harmless and vice versa.
         */
        switch (hw->phy.media_type) {
        case ixgbe_media_type_backplane:
                /* some MAC's need RMW protection on AUTOC */
                ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &reg_bp);
                if (ret_val)
                        return ret_val;

                fallthrough; /* only backplane uses autoc */
        case ixgbe_media_type_fiber:
                reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);

                break;
        case ixgbe_media_type_copper:
                hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
                                        MDIO_MMD_AN, &reg_cu);
                break;
        default:
                break;
        }

        /*
         * The possible values of fc.requested_mode are:
         * 0: Flow control is completely disabled
         * 1: Rx flow control is enabled (we can receive pause frames,
         *    but not send pause frames).
         * 2: Tx flow control is enabled (we can send pause frames but
         *    we do not support receiving pause frames).
         * 3: Both Rx and Tx flow control (symmetric) are enabled.
         * other: Invalid.
         */
        switch (hw->fc.requested_mode) {
        case ixgbe_fc_none:
                /* Flow control completely disabled by software override. */
                reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
                if (hw->phy.media_type == ixgbe_media_type_backplane)
                        reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
                                    IXGBE_AUTOC_ASM_PAUSE);
                else if (hw->phy.media_type == ixgbe_media_type_copper)
                        reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
                break;
        case ixgbe_fc_tx_pause:
                /*
                 * Tx Flow control is enabled, and Rx Flow control is
                 * disabled by software override.
                 */
                reg |= IXGBE_PCS1GANA_ASM_PAUSE;
                reg &= ~IXGBE_PCS1GANA_SYM_PAUSE;
                if (hw->phy.media_type == ixgbe_media_type_backplane) {
                        reg_bp |= IXGBE_AUTOC_ASM_PAUSE;
                        reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE;
                } else if (hw->phy.media_type == ixgbe_media_type_copper) {
                        reg_cu |= IXGBE_TAF_ASM_PAUSE;
                        reg_cu &= ~IXGBE_TAF_SYM_PAUSE;
                }
                break;
        case ixgbe_fc_rx_pause:
                /*
                 * Rx Flow control is enabled and Tx Flow control is
                 * disabled by software override. Since there really
                 * isn't a way to advertise that we are capable of RX
                 * Pause ONLY, we will advertise that we support both
                 * symmetric and asymmetric Rx PAUSE, as such we fall
                 * through to the fc_full statement.  Later, we will
                 * disable the adapter's ability to send PAUSE frames.
                 */
        case ixgbe_fc_full:
                /* Flow control (both Rx and Tx) is enabled by SW override. */
                reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE;
                if (hw->phy.media_type == ixgbe_media_type_backplane)
                        reg_bp |= IXGBE_AUTOC_SYM_PAUSE |
                                  IXGBE_AUTOC_ASM_PAUSE;
                else if (hw->phy.media_type == ixgbe_media_type_copper)
                        reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE;
                break;
        default:
                hw_dbg(hw, "Flow control param set incorrectly\n");
                return -EIO;
        }

        if (hw->mac.type != ixgbe_mac_X540) {
                /*
                 * Enable auto-negotiation between the MAC & PHY;
                 * the MAC will advertise clause 37 flow control.
                 */
                IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
                reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);

                /* Disable AN timeout */
                if (hw->fc.strict_ieee)
                        reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;

                IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
                hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
        }

        /*
         * AUTOC restart handles negotiation of 1G and 10G on backplane
         * and copper. There is no need to set the PCS1GCTL register.
         *
         */
        if (hw->phy.media_type == ixgbe_media_type_backplane) {
                /* Need the SW/FW semaphore around AUTOC writes if 82599 and
                 * LESM is on, likewise reset_pipeline requries the lock as
                 * it also writes AUTOC.
                 */
                ret_val = hw->mac.ops.prot_autoc_write(hw, reg_bp, locked);
                if (ret_val)
                        return ret_val;

        } else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
                   ixgbe_device_supports_autoneg_fc(hw)) {
                hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
                                      MDIO_MMD_AN, reg_cu);
        }

        hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
        return ret_val;
}

/**
 *  ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
 *  @hw: pointer to hardware structure
 *
 *  Starts the hardware by filling the bus info structure and media type, clears
 *  all on chip counters, initializes receive address registers, multicast
 *  table, VLAN filter table, calls routine to set up link and flow control
 *  settings, and leaves transmit and receive units disabled and uninitialized
 **/
int ixgbe_start_hw_generic(struct ixgbe_hw *hw)
{
        u16 device_caps;
        u32 ctrl_ext;
        int ret_val;

        /* Set the media type */
        hw->phy.media_type = hw->mac.ops.get_media_type(hw);

        /* Identify the PHY */
        hw->phy.ops.identify(hw);

        /* Clear the VLAN filter table */
        hw->mac.ops.clear_vfta(hw);

        /* Clear statistics registers */
        hw->mac.ops.clear_hw_cntrs(hw);

        /* Set No Snoop Disable */
        ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT);
        ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS;
        IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext);
        IXGBE_WRITE_FLUSH(hw);

        /* Setup flow control if method for doing so */
        if (hw->mac.ops.setup_fc) {
                ret_val = hw->mac.ops.setup_fc(hw);
                if (ret_val)
                        return ret_val;
        }

        /* Cashe bit indicating need for crosstalk fix */
        switch (hw->mac.type) {
        case ixgbe_mac_82599EB:
        case ixgbe_mac_X550EM_x:
        case ixgbe_mac_x550em_a:
                hw->mac.ops.get_device_caps(hw, &device_caps);
                if (device_caps & IXGBE_DEVICE_CAPS_NO_CROSSTALK_WR)
                        hw->need_crosstalk_fix = false;
                else
                        hw->need_crosstalk_fix = true;
                break;
        default:
                hw->need_crosstalk_fix = false;
                break;
        }

        /* Clear adapter stopped flag */
        hw->adapter_stopped = false;

        return 0;
}

/**
 *  ixgbe_start_hw_gen2 - Init sequence for common device family
 *  @hw: pointer to hw structure
 *
 * Performs the init sequence common to the second generation
 * of 10 GbE devices.
 * Devices in the second generation:
 *     82599
 *     X540
 **/
int ixgbe_start_hw_gen2(struct ixgbe_hw *hw)
{
        u32 i;

        /* Clear the rate limiters */
        for (i = 0; i < hw->mac.max_tx_queues; i++) {
                IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, i);
                IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0);
        }
        IXGBE_WRITE_FLUSH(hw);

        return 0;
}

/**
 *  ixgbe_init_hw_generic - Generic hardware initialization
 *  @hw: pointer to hardware structure
 *
 *  Initialize the hardware by resetting the hardware, filling the bus info
 *  structure and media type, clears all on chip counters, initializes receive
 *  address registers, multicast table, VLAN filter table, calls routine to set
 *  up link and flow control settings, and leaves transmit and receive units
 *  disabled and uninitialized
 **/
int ixgbe_init_hw_generic(struct ixgbe_hw *hw)
{
        int status;

        /* Reset the hardware */
        status = hw->mac.ops.reset_hw(hw);

        if (status == 0) {
                /* Start the HW */
                status = hw->mac.ops.start_hw(hw);
        }

        /* Initialize the LED link active for LED blink support */
        if (hw->mac.ops.init_led_link_act)
                hw->mac.ops.init_led_link_act(hw);

        return status;
}

/**
 *  ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters
 *  @hw: pointer to hardware structure
 *
 *  Clears all hardware statistics counters by reading them from the hardware
 *  Statistics counters are clear on read.
 **/
int ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw)
{
        u16 i = 0;

        IXGBE_READ_REG(hw, IXGBE_CRCERRS);
        IXGBE_READ_REG(hw, IXGBE_ILLERRC);
        IXGBE_READ_REG(hw, IXGBE_ERRBC);
        IXGBE_READ_REG(hw, IXGBE_MSPDC);
        for (i = 0; i < 8; i++)
                IXGBE_READ_REG(hw, IXGBE_MPC(i));

        IXGBE_READ_REG(hw, IXGBE_MLFC);
        IXGBE_READ_REG(hw, IXGBE_MRFC);
        IXGBE_READ_REG(hw, IXGBE_RLEC);
        IXGBE_READ_REG(hw, IXGBE_LXONTXC);
        IXGBE_READ_REG(hw, IXGBE_LXOFFTXC);
        if (hw->mac.type >= ixgbe_mac_82599EB) {
                IXGBE_READ_REG(hw, IXGBE_LXONRXCNT);
                IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT);
        } else {
                IXGBE_READ_REG(hw, IXGBE_LXONRXC);
                IXGBE_READ_REG(hw, IXGBE_LXOFFRXC);
        }

        for (i = 0; i < 8; i++) {
                IXGBE_READ_REG(hw, IXGBE_PXONTXC(i));
                IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i));
                if (hw->mac.type >= ixgbe_mac_82599EB) {
                        IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i));
                        IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i));
                } else {
                        IXGBE_READ_REG(hw, IXGBE_PXONRXC(i));
                        IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i));
                }
        }
        if (hw->mac.type >= ixgbe_mac_82599EB)
                for (i = 0; i < 8; i++)
                        IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i));
        IXGBE_READ_REG(hw, IXGBE_PRC64);
        IXGBE_READ_REG(hw, IXGBE_PRC127);
        IXGBE_READ_REG(hw, IXGBE_PRC255);
        IXGBE_READ_REG(hw, IXGBE_PRC511);
        IXGBE_READ_REG(hw, IXGBE_PRC1023);
        IXGBE_READ_REG(hw, IXGBE_PRC1522);
        IXGBE_READ_REG(hw, IXGBE_GPRC);
        IXGBE_READ_REG(hw, IXGBE_BPRC);
        IXGBE_READ_REG(hw, IXGBE_MPRC);
        IXGBE_READ_REG(hw, IXGBE_GPTC);
        IXGBE_READ_REG(hw, IXGBE_GORCL);
        IXGBE_READ_REG(hw, IXGBE_GORCH);
        IXGBE_READ_REG(hw, IXGBE_GOTCL);
        IXGBE_READ_REG(hw, IXGBE_GOTCH);
        if (hw->mac.type == ixgbe_mac_82598EB)
                for (i = 0; i < 8; i++)
                        IXGBE_READ_REG(hw, IXGBE_RNBC(i));
        IXGBE_READ_REG(hw, IXGBE_RUC);
        IXGBE_READ_REG(hw, IXGBE_RFC);
        IXGBE_READ_REG(hw, IXGBE_ROC);
        IXGBE_READ_REG(hw, IXGBE_RJC);
        IXGBE_READ_REG(hw, IXGBE_MNGPRC);
        IXGBE_READ_REG(hw, IXGBE_MNGPDC);
        IXGBE_READ_REG(hw, IXGBE_MNGPTC);
        IXGBE_READ_REG(hw, IXGBE_TORL);
        IXGBE_READ_REG(hw, IXGBE_TORH);
        IXGBE_READ_REG(hw, IXGBE_TPR);
        IXGBE_READ_REG(hw, IXGBE_TPT);
        IXGBE_READ_REG(hw, IXGBE_PTC64);
        IXGBE_READ_REG(hw, IXGBE_PTC127);
        IXGBE_READ_REG(hw, IXGBE_PTC255);
        IXGBE_READ_REG(hw, IXGBE_PTC511);
        IXGBE_READ_REG(hw, IXGBE_PTC1023);
        IXGBE_READ_REG(hw, IXGBE_PTC1522);
        IXGBE_READ_REG(hw, IXGBE_MPTC);
        IXGBE_READ_REG(hw, IXGBE_BPTC);
        for (i = 0; i < 16; i++) {
                IXGBE_READ_REG(hw, IXGBE_QPRC(i));
                IXGBE_READ_REG(hw, IXGBE_QPTC(i));
                if (hw->mac.type >= ixgbe_mac_82599EB) {
                        IXGBE_READ_REG(hw, IXGBE_QBRC_L(i));
                        IXGBE_READ_REG(hw, IXGBE_QBRC_H(i));
                        IXGBE_READ_REG(hw, IXGBE_QBTC_L(i));
                        IXGBE_READ_REG(hw, IXGBE_QBTC_H(i));
                        IXGBE_READ_REG(hw, IXGBE_QPRDC(i));
                } else {
                        IXGBE_READ_REG(hw, IXGBE_QBRC(i));
                        IXGBE_READ_REG(hw, IXGBE_QBTC(i));
                }
        }

        if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) {
                if (hw->phy.id == 0)
                        hw->phy.ops.identify(hw);
                hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, MDIO_MMD_PCS, &i);
                hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECH, MDIO_MMD_PCS, &i);
                hw->phy.ops.read_reg(hw, IXGBE_LDPCECL, MDIO_MMD_PCS, &i);
                hw->phy.ops.read_reg(hw, IXGBE_LDPCECH, MDIO_MMD_PCS, &i);
        }

        return 0;
}

/**
 *  ixgbe_read_pba_string_generic - Reads part number string from EEPROM
 *  @hw: pointer to hardware structure
 *  @pba_num: stores the part number string from the EEPROM
 *  @pba_num_size: part number string buffer length
 *
 *  Reads the part number string from the EEPROM.
 **/
int ixgbe_read_pba_string_generic(struct ixgbe_hw *hw, u8 *pba_num,
                                  u32 pba_num_size)
{
        int ret_val;
        u16 pba_ptr;
        u16 offset;
        u16 length;
        u16 data;

        if (pba_num == NULL) {
                hw_dbg(hw, "PBA string buffer was null\n");
                return -EINVAL;
        }

        ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data);
        if (ret_val) {
                hw_dbg(hw, "NVM Read Error\n");
                return ret_val;
        }

        ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &pba_ptr);
        if (ret_val) {
                hw_dbg(hw, "NVM Read Error\n");
                return ret_val;
        }

        /*
         * if data is not ptr guard the PBA must be in legacy format which
         * means pba_ptr is actually our second data word for the PBA number
         * and we can decode it into an ascii string
         */
        if (data != IXGBE_PBANUM_PTR_GUARD) {
                hw_dbg(hw, "NVM PBA number is not stored as string\n");

                /* we will need 11 characters to store the PBA */
                if (pba_num_size < 11) {
                        hw_dbg(hw, "PBA string buffer too small\n");
                        return -ENOSPC;
                }

                /* extract hex string from data and pba_ptr */
                pba_num[0] = (data >> 12) & 0xF;
                pba_num[1] = (data >> 8) & 0xF;
                pba_num[2] = (data >> 4) & 0xF;
                pba_num[3] = data & 0xF;
                pba_num[4] = (pba_ptr >> 12) & 0xF;
                pba_num[5] = (pba_ptr >> 8) & 0xF;
                pba_num[6] = '-';
                pba_num[7] = 0;
                pba_num[8] = (pba_ptr >> 4) & 0xF;
                pba_num[9] = pba_ptr & 0xF;

                /* put a null character on the end of our string */
                pba_num[10] = '\0';

                /* switch all the data but the '-' to hex char */
                for (offset = 0; offset < 10; offset++) {
                        if (pba_num[offset] < 0xA)
                                pba_num[offset] += '0';
                        else if (pba_num[offset] < 0x10)
                                pba_num[offset] += 'A' - 0xA;
                }

                return 0;
        }

        ret_val = hw->eeprom.ops.read(hw, pba_ptr, &length);
        if (ret_val) {
                hw_dbg(hw, "NVM Read Error\n");
                return ret_val;
        }

        if (length == 0xFFFF || length == 0) {
                hw_dbg(hw, "NVM PBA number section invalid length\n");
                return -EIO;
        }

        /* check if pba_num buffer is big enough */
        if (pba_num_size  < (((u32)length * 2) - 1)) {
                hw_dbg(hw, "PBA string buffer too small\n");
                return -ENOSPC;
        }

        /* trim pba length from start of string */
        pba_ptr++;
        length--;

        for (offset = 0; offset < length; offset++) {
                ret_val = hw->eeprom.ops.read(hw, pba_ptr + offset, &data);
                if (ret_val) {
                        hw_dbg(hw, "NVM Read Error\n");
                        return ret_val;
                }
                pba_num[offset * 2] = (u8)(data >> 8);
                pba_num[(offset * 2) + 1] = (u8)(data & 0xFF);
        }
        pba_num[offset * 2] = '\0';

        return 0;
}

/**
 *  ixgbe_get_mac_addr_generic - Generic get MAC address
 *  @hw: pointer to hardware structure
 *  @mac_addr: Adapter MAC address
 *
 *  Reads the adapter's MAC address from first Receive Address Register (RAR0)
 *  A reset of the adapter must be performed prior to calling this function
 *  in order for the MAC address to have been loaded from the EEPROM into RAR0
 **/
int ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr)
{
        u32 rar_high;
        u32 rar_low;
        u16 i;

        rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0));
        rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0));

        for (i = 0; i < 4; i++)
                mac_addr[i] = (u8)(rar_low >> (i*8));

        for (i = 0; i < 2; i++)
                mac_addr[i+4] = (u8)(rar_high >> (i*8));

        return 0;
}

enum ixgbe_bus_width ixgbe_convert_bus_width(u16 link_status)
{
        switch (link_status & IXGBE_PCI_LINK_WIDTH) {
        case IXGBE_PCI_LINK_WIDTH_1:
                return ixgbe_bus_width_pcie_x1;
        case IXGBE_PCI_LINK_WIDTH_2:
                return ixgbe_bus_width_pcie_x2;
        case IXGBE_PCI_LINK_WIDTH_4:
                return ixgbe_bus_width_pcie_x4;
        case IXGBE_PCI_LINK_WIDTH_8:
                return ixgbe_bus_width_pcie_x8;
        default:
                return ixgbe_bus_width_unknown;
        }
}

enum ixgbe_bus_speed ixgbe_convert_bus_speed(u16 link_status)
{
        switch (link_status & IXGBE_PCI_LINK_SPEED) {
        case IXGBE_PCI_LINK_SPEED_2500:
                return ixgbe_bus_speed_2500;
        case IXGBE_PCI_LINK_SPEED_5000:
                return ixgbe_bus_speed_5000;
        case IXGBE_PCI_LINK_SPEED_8000:
                return ixgbe_bus_speed_8000;
        default:
                return ixgbe_bus_speed_unknown;
        }
}

/**
 *  ixgbe_get_bus_info_generic - Generic set PCI bus info
 *  @hw: pointer to hardware structure
 *
 *  Sets the PCI bus info (speed, width, type) within the ixgbe_hw structure
 **/
int ixgbe_get_bus_info_generic(struct ixgbe_hw *hw)
{
        u16 link_status;

        hw->bus.type = ixgbe_bus_type_pci_express;

        /* Get the negotiated link width and speed from PCI config space */
        link_status = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_LINK_STATUS);

        hw->bus.width = ixgbe_convert_bus_width(link_status);
        hw->bus.speed = ixgbe_convert_bus_speed(link_status);

        hw->mac.ops.set_lan_id(hw);

        return 0;
}

/**
 *  ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices
 *  @hw: pointer to the HW structure
 *
 *  Determines the LAN function id by reading memory-mapped registers
 *  and swaps the port value if requested.
 **/
void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw)
{
        struct ixgbe_bus_info *bus = &hw->bus;
        u16 ee_ctrl_4;
        u32 reg;

        reg = IXGBE_READ_REG(hw, IXGBE_STATUS);
        bus->func = FIELD_GET(IXGBE_STATUS_LAN_ID, reg);
        bus->lan_id = bus->func;

        /* check for a port swap */
        reg = IXGBE_READ_REG(hw, IXGBE_FACTPS(hw));
        if (reg & IXGBE_FACTPS_LFS)
                bus->func ^= 0x1;

        /* Get MAC instance from EEPROM for configuring CS4227 */
        if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP) {
                hw->eeprom.ops.read(hw, IXGBE_EEPROM_CTRL_4, &ee_ctrl_4);
                bus->instance_id = FIELD_GET(IXGBE_EE_CTRL_4_INST_ID,
                                             ee_ctrl_4);
        }
}

/**
 *  ixgbe_stop_adapter_generic - Generic stop Tx/Rx units
 *  @hw: pointer to hardware structure
 *
 *  Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts,
 *  disables transmit and receive units. The adapter_stopped flag is used by
 *  the shared code and drivers to determine if the adapter is in a stopped
 *  state and should not touch the hardware.
 **/
int ixgbe_stop_adapter_generic(struct ixgbe_hw *hw)
{
        u32 reg_val;
        u16 i;

        /*
         * Set the adapter_stopped flag so other driver functions stop touching
         * the hardware
         */
        hw->adapter_stopped = true;

        /* Disable the receive unit */
        hw->mac.ops.disable_rx(hw);

        /* Clear interrupt mask to stop interrupts from being generated */
        IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK);

        /* Clear any pending interrupts, flush previous writes */
        IXGBE_READ_REG(hw, IXGBE_EICR);

        /* Disable the transmit unit.  Each queue must be disabled. */
        for (i = 0; i < hw->mac.max_tx_queues; i++)
                IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH);

        /* Disable the receive unit by stopping each queue */
        for (i = 0; i < hw->mac.max_rx_queues; i++) {
                reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i));
                reg_val &= ~IXGBE_RXDCTL_ENABLE;
                reg_val |= IXGBE_RXDCTL_SWFLSH;
                IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val);
        }

        /* flush all queues disables */
        IXGBE_WRITE_FLUSH(hw);
        usleep_range(1000, 2000);

        /*
         * Prevent the PCI-E bus from hanging by disabling PCI-E primary
         * access and verify no pending requests
         */
        return ixgbe_disable_pcie_primary(hw);
}

/**
 *  ixgbe_init_led_link_act_generic - Store the LED index link/activity.
 *  @hw: pointer to hardware structure
 *
 *  Store the index for the link active LED. This will be used to support
 *  blinking the LED.
 **/
int ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw)
{
        struct ixgbe_mac_info *mac = &hw->mac;
        u32 led_reg, led_mode;
        u16 i;

        led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);

        /* Get LED link active from the LEDCTL register */
        for (i = 0; i < 4; i++) {
                led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i);

                if ((led_mode & IXGBE_LED_MODE_MASK_BASE) ==
                    IXGBE_LED_LINK_ACTIVE) {
                        mac->led_link_act = i;
                        return 0;
                }
        }

        /* If LEDCTL register does not have the LED link active set, then use
         * known MAC defaults.
         */
        switch (hw->mac.type) {
        case ixgbe_mac_x550em_a:
                mac->led_link_act = 0;
                break;
        case ixgbe_mac_X550EM_x:
                mac->led_link_act = 1;
                break;
        default:
                mac->led_link_act = 2;
        }

        return 0;
}

/**
 *  ixgbe_led_on_generic - Turns on the software controllable LEDs.
 *  @hw: pointer to hardware structure
 *  @index: led number to turn on
 **/
int ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index)
{
        u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);

        if (index > 3)
                return -EINVAL;

        /* To turn on the LED, set mode to ON. */
        led_reg &= ~IXGBE_LED_MODE_MASK(index);
        led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index);
        IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
        IXGBE_WRITE_FLUSH(hw);

        return 0;
}

/**
 *  ixgbe_led_off_generic - Turns off the software controllable LEDs.
 *  @hw: pointer to hardware structure
 *  @index: led number to turn off
 **/
int ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index)
{
        u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);

        if (index > 3)
                return -EINVAL;

        /* To turn off the LED, set mode to OFF. */
        led_reg &= ~IXGBE_LED_MODE_MASK(index);
        led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index);
        IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
        IXGBE_WRITE_FLUSH(hw);

        return 0;
}

/**
 *  ixgbe_init_eeprom_params_generic - Initialize EEPROM params
 *  @hw: pointer to hardware structure
 *
 *  Initializes the EEPROM parameters ixgbe_eeprom_info within the
 *  ixgbe_hw struct in order to set up EEPROM access.
 **/
int ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw)
{
        struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
        u32 eec;
        u16 eeprom_size;

        if (eeprom->type == ixgbe_eeprom_uninitialized) {
                eeprom->type = ixgbe_eeprom_none;
                /* Set default semaphore delay to 10ms which is a well
                 * tested value */
                eeprom->semaphore_delay = 10;
                /* Clear EEPROM page size, it will be initialized as needed */
                eeprom->word_page_size = 0;

                /*
                 * Check for EEPROM present first.
                 * If not present leave as none
                 */
                eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
                if (eec & IXGBE_EEC_PRES) {
                        eeprom->type = ixgbe_eeprom_spi;

                        /*
                         * SPI EEPROM is assumed here.  This code would need to
                         * change if a future EEPROM is not SPI.
                         */
                        eeprom_size = FIELD_GET(IXGBE_EEC_SIZE, eec);
                        eeprom->word_size = BIT(eeprom_size +
                                                IXGBE_EEPROM_WORD_SIZE_SHIFT);
                }

                if (eec & IXGBE_EEC_ADDR_SIZE)
                        eeprom->address_bits = 16;
                else
                        eeprom->address_bits = 8;
                hw_dbg(hw, "Eeprom params: type = %d, size = %d, address bits: %d\n",
                       eeprom->type, eeprom->word_size, eeprom->address_bits);
        }

        return 0;
}

/**
 *  ixgbe_write_eeprom_buffer_bit_bang_generic - Write EEPROM using bit-bang
 *  @hw: pointer to hardware structure
 *  @offset: offset within the EEPROM to write
 *  @words: number of words
 *  @data: 16 bit word(s) to write to EEPROM
 *
 *  Reads 16 bit word(s) from EEPROM through bit-bang method
 **/
int ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
                                               u16 words, u16 *data)
{
        u16 i, count;
        int status;

        hw->eeprom.ops.init_params(hw);

        if (words == 0 || (offset + words > hw->eeprom.word_size))
                return -EINVAL;

        /*
         * The EEPROM page size cannot be queried from the chip. We do lazy
         * initialization. It is worth to do that when we write large buffer.
         */
        if ((hw->eeprom.word_page_size == 0) &&
            (words > IXGBE_EEPROM_PAGE_SIZE_MAX))
                ixgbe_detect_eeprom_page_size_generic(hw, offset);

        /*
         * We cannot hold synchronization semaphores for too long
         * to avoid other entity starvation. However it is more efficient
         * to read in bursts than synchronizing access for each word.
         */
        for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
                count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
                         IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);
                status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset + i,
                                                            count, &data[i]);

                if (status != 0)
                        break;
        }

        return status;
}

/**
 *  ixgbe_write_eeprom_buffer_bit_bang - Writes 16 bit word(s) to EEPROM
 *  @hw: pointer to hardware structure
 *  @offset: offset within the EEPROM to be written to
 *  @words: number of word(s)
 *  @data: 16 bit word(s) to be written to the EEPROM
 *
 *  If ixgbe_eeprom_update_checksum is not called after this function, the
 *  EEPROM will most likely contain an invalid checksum.
 **/
static int ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
                                              u16 words, u16 *data)
{
        u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI;
        u16 page_size;
        int status;
        u16 word;
        u16 i;

        /* Prepare the EEPROM for writing  */
        status = ixgbe_acquire_eeprom(hw);
        if (status)
                return status;

        if (ixgbe_ready_eeprom(hw) != 0) {
                ixgbe_release_eeprom(hw);
                return -EIO;
        }

        for (i = 0; i < words; i++) {
                ixgbe_standby_eeprom(hw);

                /* Send the WRITE ENABLE command (8 bit opcode) */
                ixgbe_shift_out_eeprom_bits(hw,
                                            IXGBE_EEPROM_WREN_OPCODE_SPI,
                                            IXGBE_EEPROM_OPCODE_BITS);

                ixgbe_standby_eeprom(hw);

                /* Some SPI eeproms use the 8th address bit embedded
                 * in the opcode
                 */
                if ((hw->eeprom.address_bits == 8) &&
                    ((offset + i) >= 128))
                        write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;

                /* Send the Write command (8-bit opcode + addr) */
                ixgbe_shift_out_eeprom_bits(hw, write_opcode,
                                            IXGBE_EEPROM_OPCODE_BITS);
                ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
                                            hw->eeprom.address_bits);

                page_size = hw->eeprom.word_page_size;

                /* Send the data in burst via SPI */
                do {
                        word = data[i];
                        word = (word >> 8) | (word << 8);
                        ixgbe_shift_out_eeprom_bits(hw, word, 16);

                        if (page_size == 0)
                                break;

                        /* do not wrap around page */
                        if (((offset + i) & (page_size - 1)) ==
                            (page_size - 1))
                                break;
                } while (++i < words);

                ixgbe_standby_eeprom(hw);
                usleep_range(10000, 20000);
        }
        /* Done with writing - release the EEPROM */
        ixgbe_release_eeprom(hw);

        return 0;
}

/**
 *  ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM
 *  @hw: pointer to hardware structure
 *  @offset: offset within the EEPROM to be written to
 *  @data: 16 bit word to be written to the EEPROM
 *
 *  If ixgbe_eeprom_update_checksum is not called after this function, the
 *  EEPROM will most likely contain an invalid checksum.
 **/
int ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
{
        hw->eeprom.ops.init_params(hw);

        if (offset >= hw->eeprom.word_size)
                return -EINVAL;

        return ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data);
}

/**
 *  ixgbe_read_eeprom_buffer_bit_bang_generic - Read EEPROM using bit-bang
 *  @hw: pointer to hardware structure
 *  @offset: offset within the EEPROM to be read
 *  @words: number of word(s)
 *  @data: read 16 bit words(s) from EEPROM
 *
 *  Reads 16 bit word(s) from EEPROM through bit-bang method
 **/
int ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
                                              u16 words, u16 *data)
{
        u16 i, count;
        int status;

        hw->eeprom.ops.init_params(hw);

        if (words == 0 || (offset + words > hw->eeprom.word_size))
                return -EINVAL;

        /*
         * We cannot hold synchronization semaphores for too long
         * to avoid other entity starvation. However it is more efficient
         * to read in bursts than synchronizing access for each word.
         */
        for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
                count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
                         IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);

                status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset + i,
                                                           count, &data[i]);

                if (status)
                        return status;
        }

        return 0;
}

/**
 *  ixgbe_read_eeprom_buffer_bit_bang - Read EEPROM using bit-bang
 *  @hw: pointer to hardware structure
 *  @offset: offset within the EEPROM to be read
 *  @words: number of word(s)
 *  @data: read 16 bit word(s) from EEPROM
 *
 *  Reads 16 bit word(s) from EEPROM through bit-bang method
 **/
static int ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
                                             u16 words, u16 *data)
{
        u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI;
        u16 word_in;
        int status;
        u16 i;

        /* Prepare the EEPROM for reading  */
        status = ixgbe_acquire_eeprom(hw);
        if (status)
                return status;

        if (ixgbe_ready_eeprom(hw) != 0) {
                ixgbe_release_eeprom(hw);
                return -EIO;
        }

        for (i = 0; i < words; i++) {
                ixgbe_standby_eeprom(hw);
                /* Some SPI eeproms use the 8th address bit embedded
                 * in the opcode
                 */
                if ((hw->eeprom.address_bits == 8) &&
                    ((offset + i) >= 128))
                        read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;

                /* Send the READ command (opcode + addr) */
                ixgbe_shift_out_eeprom_bits(hw, read_opcode,
                                            IXGBE_EEPROM_OPCODE_BITS);
                ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
                                            hw->eeprom.address_bits);

                /* Read the data. */
                word_in = ixgbe_shift_in_eeprom_bits(hw, 16);
                data[i] = (word_in >> 8) | (word_in << 8);
        }

        /* End this read operation */
        ixgbe_release_eeprom(hw);

        return 0;
}

/**
 *  ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang
 *  @hw: pointer to hardware structure
 *  @offset: offset within the EEPROM to be read
 *  @data: read 16 bit value from EEPROM
 *
 *  Reads 16 bit value from EEPROM through bit-bang method
 **/
int ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
                                       u16 *data)
{
        hw->eeprom.ops.init_params(hw);

        if (offset >= hw->eeprom.word_size)
                return -EINVAL;

        return ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
}

/**
 *  ixgbe_read_eerd_buffer_generic - Read EEPROM word(s) using EERD
 *  @hw: pointer to hardware structure
 *  @offset: offset of word in the EEPROM to read
 *  @words: number of word(s)
 *  @data: 16 bit word(s) from the EEPROM
 *
 *  Reads a 16 bit word(s) from the EEPROM using the EERD register.
 **/
int ixgbe_read_eerd_buffer_generic(struct ixgbe_hw *hw, u16 offset,
                                   u16 words, u16 *data)
{
        int status;
        u32 eerd;
        u32 i;

        hw->eeprom.ops.init_params(hw);

        if (words == 0 || offset >= hw->eeprom.word_size)
                return -EINVAL;

        for (i = 0; i < words; i++) {
                eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
                       IXGBE_EEPROM_RW_REG_START;

                IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd);
                status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_READ);

                if (status == 0) {
                        data[i] = (IXGBE_READ_REG(hw, IXGBE_EERD) >>
                                   IXGBE_EEPROM_RW_REG_DATA);
                } else {
                        hw_dbg(hw, "Eeprom read timed out\n");
                        return status;
                }
        }

        return 0;
}

/**
 *  ixgbe_detect_eeprom_page_size_generic - Detect EEPROM page size
 *  @hw: pointer to hardware structure
 *  @offset: offset within the EEPROM to be used as a scratch pad
 *
 *  Discover EEPROM page size by writing marching data at given offset.
 *  This function is called only when we are writing a new large buffer
 *  at given offset so the data would be overwritten anyway.
 **/
static int ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
                                                 u16 offset)
{
        u16 data[IXGBE_EEPROM_PAGE_SIZE_MAX];
        int status;
        u16 i;

        for (i = 0; i < IXGBE_EEPROM_PAGE_SIZE_MAX; i++)
                data[i] = i;

        hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX;
        status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset,
                                             IXGBE_EEPROM_PAGE_SIZE_MAX, data);
        hw->eeprom.word_page_size = 0;
        if (status)
                return status;

        status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
        if (status)
                return status;

        /*
         * When writing in burst more than the actual page size
         * EEPROM address wraps around current page.
         */
        hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX - data[0];

        hw_dbg(hw, "Detected EEPROM page size = %d words.\n",
               hw->eeprom.word_page_size);
        return 0;
}

/**
 *  ixgbe_read_eerd_generic - Read EEPROM word using EERD
 *  @hw: pointer to hardware structure
 *  @offset: offset of  word in the EEPROM to read
 *  @data: word read from the EEPROM
 *
 *  Reads a 16 bit word from the EEPROM using the EERD register.
 **/
int ixgbe_read_eerd_generic(struct ixgbe_hw *hw, u16 offset, u16 *data)
{
        return ixgbe_read_eerd_buffer_generic(hw, offset, 1, data);
}

/**
 *  ixgbe_write_eewr_buffer_generic - Write EEPROM word(s) using EEWR
 *  @hw: pointer to hardware structure
 *  @offset: offset of  word in the EEPROM to write
 *  @words: number of words
 *  @data: word(s) write to the EEPROM
 *
 *  Write a 16 bit word(s) to the EEPROM using the EEWR register.
 **/
int ixgbe_write_eewr_buffer_generic(struct ixgbe_hw *hw, u16 offset,
                                    u16 words, u16 *data)
{
        int status;
        u32 eewr;
        u16 i;

        hw->eeprom.ops.init_params(hw);

        if (words == 0 || offset >= hw->eeprom.word_size)
                return -EINVAL;

        for (i = 0; i < words; i++) {
                eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
                       (data[i] << IXGBE_EEPROM_RW_REG_DATA) |
                       IXGBE_EEPROM_RW_REG_START;

                status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
                if (status) {
                        hw_dbg(hw, "Eeprom write EEWR timed out\n");
                        return status;
                }

                IXGBE_WRITE_REG(hw, IXGBE_EEWR, eewr);

                status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
                if (status) {
                        hw_dbg(hw, "Eeprom write EEWR timed out\n");
                        return status;
                }
        }

        return 0;
}

/**
 *  ixgbe_write_eewr_generic - Write EEPROM word using EEWR
 *  @hw: pointer to hardware structure
 *  @offset: offset of  word in the EEPROM to write
 *  @data: word write to the EEPROM
 *
 *  Write a 16 bit word to the EEPROM using the EEWR register.
 **/
int ixgbe_write_eewr_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
{
        return ixgbe_write_eewr_buffer_generic(hw, offset, 1, &data);
}

/**
 *  ixgbe_poll_eerd_eewr_done - Poll EERD read or EEWR write status
 *  @hw: pointer to hardware structure
 *  @ee_reg: EEPROM flag for polling
 *
 *  Polls the status bit (bit 1) of the EERD or EEWR to determine when the
 *  read or write is done respectively.
 **/
static int ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg)
{
        u32 i;
        u32 reg;

        for (i = 0; i < IXGBE_EERD_EEWR_ATTEMPTS; i++) {
                if (ee_reg == IXGBE_NVM_POLL_READ)
                        reg = IXGBE_READ_REG(hw, IXGBE_EERD);
                else
                        reg = IXGBE_READ_REG(hw, IXGBE_EEWR);

                if (reg & IXGBE_EEPROM_RW_REG_DONE) {
                        return 0;
                }
                udelay(5);
        }
        return -EIO;
}

/**
 *  ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang
 *  @hw: pointer to hardware structure
 *
 *  Prepares EEPROM for access using bit-bang method. This function should
 *  be called before issuing a command to the EEPROM.
 **/
static int ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
{
        u32 eec;
        u32 i;

        if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0)
                return -EBUSY;

        eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));

        /* Request EEPROM Access */
        eec |= IXGBE_EEC_REQ;
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);

        for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) {
                eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
                if (eec & IXGBE_EEC_GNT)
                        break;
                udelay(5);
        }

        /* Release if grant not acquired */
        if (!(eec & IXGBE_EEC_GNT)) {
                eec &= ~IXGBE_EEC_REQ;
                IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
                hw_dbg(hw, "Could not acquire EEPROM grant\n");

                hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
                return -EIO;
        }

        /* Setup EEPROM for Read/Write */
        /* Clear CS and SK */
        eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK);
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
        IXGBE_WRITE_FLUSH(hw);
        udelay(1);
        return 0;
}

/**
 *  ixgbe_get_eeprom_semaphore - Get hardware semaphore
 *  @hw: pointer to hardware structure
 *
 *  Sets the hardware semaphores so EEPROM access can occur for bit-bang method
 **/
static int ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw)
{
        u32 timeout = 2000;
        u32 i;
        u32 swsm;

        /* Get SMBI software semaphore between device drivers first */
        for (i = 0; i < timeout; i++) {
                /*
                 * If the SMBI bit is 0 when we read it, then the bit will be
                 * set and we have the semaphore
                 */
                swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
                if (!(swsm & IXGBE_SWSM_SMBI))
                        break;
                usleep_range(50, 100);
        }

        if (i == timeout) {
                hw_dbg(hw, "Driver can't access the Eeprom - SMBI Semaphore not granted.\n");
                /* this release is particularly important because our attempts
                 * above to get the semaphore may have succeeded, and if there
                 * was a timeout, we should unconditionally clear the semaphore
                 * bits to free the driver to make progress
                 */
                ixgbe_release_eeprom_semaphore(hw);

                usleep_range(50, 100);
                /* one last try
                 * If the SMBI bit is 0 when we read it, then the bit will be
                 * set and we have the semaphore
                 */
                swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
                if (swsm & IXGBE_SWSM_SMBI) {
                        hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n");
                        return -EIO;
                }
        }

        /* Now get the semaphore between SW/FW through the SWESMBI bit */
        for (i = 0; i < timeout; i++) {
                swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));

                /* Set the SW EEPROM semaphore bit to request access */
                swsm |= IXGBE_SWSM_SWESMBI;
                IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);

                /* If we set the bit successfully then we got the
                 * semaphore.
                 */
                swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
                if (swsm & IXGBE_SWSM_SWESMBI)
                        break;

                usleep_range(50, 100);
        }

        /* Release semaphores and return error if SW EEPROM semaphore
         * was not granted because we don't have access to the EEPROM
         */
        if (i >= timeout) {
                hw_dbg(hw, "SWESMBI Software EEPROM semaphore not granted.\n");
                ixgbe_release_eeprom_semaphore(hw);
                return -EIO;
        }

        return 0;
}

/**
 *  ixgbe_release_eeprom_semaphore - Release hardware semaphore
 *  @hw: pointer to hardware structure
 *
 *  This function clears hardware semaphore bits.
 **/
static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw)
{
        u32 swsm;

        swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));

        /* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */
        swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI);
        IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
        IXGBE_WRITE_FLUSH(hw);
}

/**
 *  ixgbe_ready_eeprom - Polls for EEPROM ready
 *  @hw: pointer to hardware structure
 **/
static int ixgbe_ready_eeprom(struct ixgbe_hw *hw)
{
        u16 i;
        u8 spi_stat_reg;

        /*
         * Read "Status Register" repeatedly until the LSB is cleared.  The
         * EEPROM will signal that the command has been completed by clearing
         * bit 0 of the internal status register.  If it's not cleared within
         * 5 milliseconds, then error out.
         */
        for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) {
                ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI,
                                            IXGBE_EEPROM_OPCODE_BITS);
                spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8);
                if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI))
                        break;

                udelay(5);
                ixgbe_standby_eeprom(hw);
        }

        /*
         * On some parts, SPI write time could vary from 0-20mSec on 3.3V
         * devices (and only 0-5mSec on 5V devices)
         */
        if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) {
                hw_dbg(hw, "SPI EEPROM Status error\n");
                return -EIO;
        }

        return 0;
}

/**
 *  ixgbe_standby_eeprom - Returns EEPROM to a "standby" state
 *  @hw: pointer to hardware structure
 **/
static void ixgbe_standby_eeprom(struct ixgbe_hw *hw)
{
        u32 eec;

        eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));

        /* Toggle CS to flush commands */
        eec |= IXGBE_EEC_CS;
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
        IXGBE_WRITE_FLUSH(hw);
        udelay(1);
        eec &= ~IXGBE_EEC_CS;
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
        IXGBE_WRITE_FLUSH(hw);
        udelay(1);
}

/**
 *  ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM.
 *  @hw: pointer to hardware structure
 *  @data: data to send to the EEPROM
 *  @count: number of bits to shift out
 **/
static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
                                        u16 count)
{
        u32 eec;
        u32 mask;
        u32 i;

        eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));

        /*
         * Mask is used to shift "count" bits of "data" out to the EEPROM
         * one bit at a time.  Determine the starting bit based on count
         */
        mask = BIT(count - 1);

        for (i = 0; i < count; i++) {
                /*
                 * A "1" is shifted out to the EEPROM by setting bit "DI" to a
                 * "1", and then raising and then lowering the clock (the SK
                 * bit controls the clock input to the EEPROM).  A "0" is
                 * shifted out to the EEPROM by setting "DI" to "0" and then
                 * raising and then lowering the clock.
                 */
                if (data & mask)
                        eec |= IXGBE_EEC_DI;
                else
                        eec &= ~IXGBE_EEC_DI;

                IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
                IXGBE_WRITE_FLUSH(hw);

                udelay(1);

                ixgbe_raise_eeprom_clk(hw, &eec);
                ixgbe_lower_eeprom_clk(hw, &eec);

                /*
                 * Shift mask to signify next bit of data to shift in to the
                 * EEPROM
                 */
                mask = mask >> 1;
        }

        /* We leave the "DI" bit set to "0" when we leave this routine. */
        eec &= ~IXGBE_EEC_DI;
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
        IXGBE_WRITE_FLUSH(hw);
}

/**
 *  ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM
 *  @hw: pointer to hardware structure
 *  @count: number of bits to shift
 **/
static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
{
        u32 eec;
        u32 i;
        u16 data = 0;

        /*
         * In order to read a register from the EEPROM, we need to shift
         * 'count' bits in from the EEPROM. Bits are "shifted in" by raising
         * the clock input to the EEPROM (setting the SK bit), and then reading
         * the value of the "DO" bit.  During this "shifting in" process the
         * "DI" bit should always be clear.
         */
        eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));

        eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI);

        for (i = 0; i < count; i++) {
                data = data << 1;
                ixgbe_raise_eeprom_clk(hw, &eec);

                eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));

                eec &= ~(IXGBE_EEC_DI);
                if (eec & IXGBE_EEC_DO)
                        data |= 1;

                ixgbe_lower_eeprom_clk(hw, &eec);
        }

        return data;
}

/**
 *  ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input.
 *  @hw: pointer to hardware structure
 *  @eec: EEC register's current value
 **/
static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
{
        /*
         * Raise the clock input to the EEPROM
         * (setting the SK bit), then delay
         */
        *eec = *eec | IXGBE_EEC_SK;
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
        IXGBE_WRITE_FLUSH(hw);
        udelay(1);
}

/**
 *  ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input.
 *  @hw: pointer to hardware structure
 *  @eec: EEC's current value
 **/
static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
{
        /*
         * Lower the clock input to the EEPROM (clearing the SK bit), then
         * delay
         */
        *eec = *eec & ~IXGBE_EEC_SK;
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
        IXGBE_WRITE_FLUSH(hw);
        udelay(1);
}

/**
 *  ixgbe_release_eeprom - Release EEPROM, release semaphores
 *  @hw: pointer to hardware structure
 **/
static void ixgbe_release_eeprom(struct ixgbe_hw *hw)
{
        u32 eec;

        eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));

        eec |= IXGBE_EEC_CS;  /* Pull CS high */
        eec &= ~IXGBE_EEC_SK; /* Lower SCK */

        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
        IXGBE_WRITE_FLUSH(hw);

        udelay(1);

        /* Stop requesting EEPROM access */
        eec &= ~IXGBE_EEC_REQ;
        IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);

        hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);

        /*
         * Delay before attempt to obtain semaphore again to allow FW
         * access. semaphore_delay is in ms we need us for usleep_range
         */
        usleep_range(hw->eeprom.semaphore_delay * 1000,
                     hw->eeprom.semaphore_delay * 2000);
}

/**
 *  ixgbe_calc_eeprom_checksum_generic - Calculates and returns the checksum
 *  @hw: pointer to hardware structure
 **/
int ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw *hw)
{
        u16 i;
        u16 j;
        u16 checksum = 0;
        u16 length = 0;
        u16 pointer = 0;
        u16 word = 0;

        /* Include 0x0-0x3F in the checksum */
        for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) {
                if (hw->eeprom.ops.read(hw, i, &word)) {
                        hw_dbg(hw, "EEPROM read failed\n");
                        break;
                }
                checksum += word;
        }

        /* Include all data from pointers except for the fw pointer */
        for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) {
                if (hw->eeprom.ops.read(hw, i, &pointer)) {
                        hw_dbg(hw, "EEPROM read failed\n");
                        return -EIO;
                }

                /* If the pointer seems invalid */
                if (pointer == 0xFFFF || pointer == 0)
                        continue;

                if (hw->eeprom.ops.read(hw, pointer, &length)) {
                        hw_dbg(hw, "EEPROM read failed\n");
                        return -EIO;
                }

                if (length == 0xFFFF || length == 0)
                        continue;

                for (j = pointer + 1; j <= pointer + length; j++) {
                        if (hw->eeprom.ops.read(hw, j, &word)) {
                                hw_dbg(hw, "EEPROM read failed\n");
                                return -EIO;
                        }
                        checksum += word;
                }
        }

        checksum = (u16)IXGBE_EEPROM_SUM - checksum;

        return (int)checksum;
}

/**
 *  ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum
 *  @hw: pointer to hardware structure
 *  @checksum_val: calculated checksum
 *
 *  Performs checksum calculation and validates the EEPROM checksum.  If the
 *  caller does not need checksum_val, the value can be NULL.
 **/
int ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw,
                                           u16 *checksum_val)
{
        u16 read_checksum = 0;
        u16 checksum;
        int status;

        /*
         * Read the first word from the EEPROM. If this times out or fails, do
         * not continue or we could be in for a very long wait while every
         * EEPROM read fails
         */
        status = hw->eeprom.ops.read(hw, 0, &checksum);
        if (status) {
                hw_dbg(hw, "EEPROM read failed\n");
                return status;
        }

        status = hw->eeprom.ops.calc_checksum(hw);
        if (status < 0)
                return status;

        checksum = (u16)(status & 0xffff);

        status = hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum);
        if (status) {
                hw_dbg(hw, "EEPROM read failed\n");
                return status;
        }

        /* Verify read checksum from EEPROM is the same as
         * calculated checksum
         */
        if (read_checksum != checksum)
                status = -EIO;

        /* If the user cares, return the calculated checksum */
        if (checksum_val)
                *checksum_val = checksum;

        return status;
}

/**
 *  ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum
 *  @hw: pointer to hardware structure
 **/
int ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw)
{
        u16 checksum;
        int status;

        /*
         * Read the first word from the EEPROM. If this times out or fails, do
         * not continue or we could be in for a very long wait while every
         * EEPROM read fails
         */
        status = hw->eeprom.ops.read(hw, 0, &checksum);
        if (status) {
                hw_dbg(hw, "EEPROM read failed\n");
                return status;
        }

        status = hw->eeprom.ops.calc_checksum(hw);
        if (status < 0)
                return status;

        checksum = (u16)(status & 0xffff);

        status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, checksum);

        return status;
}

/**
 *  ixgbe_set_rar_generic - Set Rx address register
 *  @hw: pointer to hardware structure
 *  @index: Receive address register to write
 *  @addr: Address to put into receive address register
 *  @vmdq: VMDq "set" or "pool" index
 *  @enable_addr: set flag that address is active
 *
 *  Puts an ethernet address into a receive address register.
 **/
int ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq,
                          u32 enable_addr)
{
        u32 rar_low, rar_high;
        u32 rar_entries = hw->mac.num_rar_entries;

        /* Make sure we are using a valid rar index range */
        if (index >= rar_entries) {
                hw_dbg(hw, "RAR index %d is out of range.\n", index);
                return -EINVAL;
        }

        /* setup VMDq pool selection before this RAR gets enabled */
        hw->mac.ops.set_vmdq(hw, index, vmdq);

        /*
         * HW expects these in little endian so we reverse the byte
         * order from network order (big endian) to little endian
         */
        rar_low = ((u32)addr[0] |
                   ((u32)addr[1] << 8) |
                   ((u32)addr[2] << 16) |
                   ((u32)addr[3] << 24));
        /*
         * Some parts put the VMDq setting in the extra RAH bits,
         * so save everything except the lower 16 bits that hold part
         * of the address and the address valid bit.
         */
        rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
        rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);
        rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8));

        if (enable_addr != 0)
                rar_high |= IXGBE_RAH_AV;

        /* Record lower 32 bits of MAC address and then make
         * sure that write is flushed to hardware before writing
         * the upper 16 bits and setting the valid bit.
         */
        IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low);
        IXGBE_WRITE_FLUSH(hw);
        IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);

        return 0;
}

/**
 *  ixgbe_clear_rar_generic - Remove Rx address register
 *  @hw: pointer to hardware structure
 *  @index: Receive address register to write
 *
 *  Clears an ethernet address from a receive address register.
 **/
int ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index)
{
        u32 rar_high;
        u32 rar_entries = hw->mac.num_rar_entries;

        /* Make sure we are using a valid rar index range */
        if (index >= rar_entries) {
                hw_dbg(hw, "RAR index %d is out of range.\n", index);
                return -EINVAL;
        }

        /*
         * Some parts put the VMDq setting in the extra RAH bits,
         * so save everything except the lower 16 bits that hold part
         * of the address and the address valid bit.
         */
        rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
        rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);

        /* Clear the address valid bit and upper 16 bits of the address
         * before clearing the lower bits. This way we aren't updating
         * a live filter.
         */
        IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);
        IXGBE_WRITE_FLUSH(hw);
        IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0);

        /* clear VMDq pool/queue selection for this RAR */
        hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL);

        return 0;
}

/**
 *  ixgbe_init_rx_addrs_generic - Initializes receive address filters.
 *  @hw: pointer to hardware structure
 *
 *  Places the MAC address in receive address register 0 and clears the rest
 *  of the receive address registers. Clears the multicast table. Assumes
 *  the receiver is in reset when the routine is called.
 **/
int ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw)
{
        u32 i;
        u32 rar_entries = hw->mac.num_rar_entries;

        /*
         * If the current mac address is valid, assume it is a software override
         * to the permanent address.
         * Otherwise, use the permanent address from the eeprom.
         */
        if (!is_valid_ether_addr(hw->mac.addr)) {
                /* Get the MAC address from the RAR0 for later reference */
                hw->mac.ops.get_mac_addr(hw, hw->mac.addr);

                hw_dbg(hw, " Keeping Current RAR0 Addr =%pM\n", hw->mac.addr);
        } else {
                /* Setup the receive address. */
                hw_dbg(hw, "Overriding MAC Address in RAR[0]\n");
                hw_dbg(hw, " New MAC Addr =%pM\n", hw->mac.addr);

                hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV);
        }

        /*  clear VMDq pool/queue selection for RAR 0 */
        hw->mac.ops.clear_vmdq(hw, 0, IXGBE_CLEAR_VMDQ_ALL);

        hw->addr_ctrl.overflow_promisc = 0;

        hw->addr_ctrl.rar_used_count = 1;

        /* Zero out the other receive addresses. */
        hw_dbg(hw, "Clearing RAR[1-%d]\n", rar_entries - 1);
        for (i = 1; i < rar_entries; i++) {
                IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0);
                IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0);
        }

        /* Clear the MTA */
        hw->addr_ctrl.mta_in_use = 0;
        IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);

        hw_dbg(hw, " Clearing MTA\n");
        for (i = 0; i < hw->mac.mcft_size; i++)
                IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0);

        if (hw->mac.ops.init_uta_tables)
                hw->mac.ops.init_uta_tables(hw);

        return 0;
}

/**
 *  ixgbe_mta_vector - Determines bit-vector in multicast table to set
 *  @hw: pointer to hardware structure
 *  @mc_addr: the multicast address
 *
 *  Extracts the 12 bits, from a multicast address, to determine which
 *  bit-vector to set in the multicast table. The hardware uses 12 bits, from
 *  incoming rx multicast addresses, to determine the bit-vector to check in
 *  the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set
 *  by the MO field of the MCSTCTRL. The MO field is set during initialization
 *  to mc_filter_type.
 **/
static int ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr)
{
        u32 vector = 0;

        switch (hw->mac.mc_filter_type) {
        case 0:   /* use bits [47:36] of the address */
                vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
                break;
        case 1:   /* use bits [46:35] of the address */
                vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5));
                break;
        case 2:   /* use bits [45:34] of the address */
                vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
                break;
        case 3:   /* use bits [43:32] of the address */
                vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8));
                break;
        default:  /* Invalid mc_filter_type */
                hw_dbg(hw, "MC filter type param set incorrectly\n");
                break;
        }

        /* vector can only be 12-bits or boundary will be exceeded */
        vector &= 0xFFF;
        return vector;
}

/**
 *  ixgbe_set_mta - Set bit-vector in multicast table
 *  @hw: pointer to hardware structure
 *  @mc_addr: Multicast address
 *
 *  Sets the bit-vector in the multicast table.
 **/
static void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr)
{
        u32 vector;
        u32 vector_bit;
        u32 vector_reg;

        hw->addr_ctrl.mta_in_use++;

        vector = ixgbe_mta_vector(hw, mc_addr);
        hw_dbg(hw, " bit-vector = 0x%03X\n", vector);

        /*
         * The MTA is a register array of 128 32-bit registers. It is treated
         * like an array of 4096 bits.  We want to set bit
         * BitArray[vector_value]. So we figure out what register the bit is
         * in, read it, OR in the new bit, then write back the new value.  The
         * register is determined by the upper 7 bits of the vector value and
         * the bit within that register are determined by the lower 5 bits of
         * the value.
         */
        vector_reg = (vector >> 5) & 0x7F;
        vector_bit = vector & 0x1F;
        hw->mac.mta_shadow[vector_reg] |= BIT(vector_bit);
}

/**
 *  ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses
 *  @hw: pointer to hardware structure
 *  @netdev: pointer to net device structure
 *
 *  The given list replaces any existing list. Clears the MC addrs from receive
 *  address registers and the multicast table. Uses unused receive address
 *  registers for the first multicast addresses, and hashes the rest into the
 *  multicast table.
 **/
int ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw,
                                      struct net_device *netdev)
{
        struct netdev_hw_addr *ha;
        u32 i;

        /*
         * Set the new number of MC addresses that we are being requested to
         * use.
         */
        hw->addr_ctrl.num_mc_addrs = netdev_mc_count(netdev);
        hw->addr_ctrl.mta_in_use = 0;

        /* Clear mta_shadow */
        hw_dbg(hw, " Clearing MTA\n");
        memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));

        /* Update mta shadow */
        netdev_for_each_mc_addr(ha, netdev) {
                hw_dbg(hw, " Adding the multicast addresses:\n");
                ixgbe_set_mta(hw, ha->addr);
        }

        /* Enable mta */
        for (i = 0; i < hw->mac.mcft_size; i++)
                IXGBE_WRITE_REG_ARRAY(hw, IXGBE_MTA(0), i,
                                      hw->mac.mta_shadow[i]);

        if (hw->addr_ctrl.mta_in_use > 0)
                IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL,
                                IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type);

        hw_dbg(hw, "ixgbe_update_mc_addr_list_generic Complete\n");
        return 0;
}

/**
 *  ixgbe_enable_mc_generic - Enable multicast address in RAR
 *  @hw: pointer to hardware structure
 *
 *  Enables multicast address in RAR and the use of the multicast hash table.
 **/
int ixgbe_enable_mc_generic(struct ixgbe_hw *hw)
{
        struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;

        if (a->mta_in_use > 0)
                IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE |
                                hw->mac.mc_filter_type);

        return 0;
}

/**
 *  ixgbe_disable_mc_generic - Disable multicast address in RAR
 *  @hw: pointer to hardware structure
 *
 *  Disables multicast address in RAR and the use of the multicast hash table.
 **/
int ixgbe_disable_mc_generic(struct ixgbe_hw *hw)
{
        struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;

        if (a->mta_in_use > 0)
                IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);

        return 0;
}

/**
 *  ixgbe_fc_enable_generic - Enable flow control
 *  @hw: pointer to hardware structure
 *
 *  Enable flow control according to the current settings.
 **/
int ixgbe_fc_enable_generic(struct ixgbe_hw *hw)
{
        u32 mflcn_reg, fccfg_reg;
        u32 reg;
        u32 fcrtl, fcrth;
        int i;

        /* Validate the water mark configuration. */
        if (!hw->fc.pause_time)
                return -EINVAL;

        /* Low water mark of zero causes XOFF floods */
        for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
                if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
                    hw->fc.high_water[i]) {
                        if (!hw->fc.low_water[i] ||
                            hw->fc.low_water[i] >= hw->fc.high_water[i]) {
                                hw_dbg(hw, "Invalid water mark configuration\n");
                                return -EINVAL;
                        }
                }
        }

        /* Negotiate the fc mode to use */
        hw->mac.ops.fc_autoneg(hw);

        /* Disable any previous flow control settings */
        mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN);
        mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE);

        fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG);
        fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY);

        /*
         * The possible values of fc.current_mode are:
         * 0: Flow control is completely disabled
         * 1: Rx flow control is enabled (we can receive pause frames,
         *    but not send pause frames).
         * 2: Tx flow control is enabled (we can send pause frames but
         *    we do not support receiving pause frames).
         * 3: Both Rx and Tx flow control (symmetric) are enabled.
         * other: Invalid.
         */
        switch (hw->fc.current_mode) {
        case ixgbe_fc_none:
                /*
                 * Flow control is disabled by software override or autoneg.
                 * The code below will actually disable it in the HW.
                 */
                break;
        case ixgbe_fc_rx_pause:
                /*
                 * Rx Flow control is enabled and Tx Flow control is
                 * disabled by software override. Since there really
                 * isn't a way to advertise that we are capable of RX
                 * Pause ONLY, we will advertise that we support both
                 * symmetric and asymmetric Rx PAUSE.  Later, we will
                 * disable the adapter's ability to send PAUSE frames.
                 */
                mflcn_reg |= IXGBE_MFLCN_RFCE;
                break;
        case ixgbe_fc_tx_pause:
                /*
                 * Tx Flow control is enabled, and Rx Flow control is
                 * disabled by software override.
                 */
                fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
                break;
        case ixgbe_fc_full:
                /* Flow control (both Rx and Tx) is enabled by SW override. */
                mflcn_reg |= IXGBE_MFLCN_RFCE;
                fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
                break;
        default:
                hw_dbg(hw, "Flow control param set incorrectly\n");
                return -EIO;
        }

        /* Set 802.3x based flow control settings. */
        mflcn_reg |= IXGBE_MFLCN_DPF;
        IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg);
        IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg);

        /* Set up and enable Rx high/low water mark thresholds, enable XON. */
        for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
                if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
                    hw->fc.high_water[i]) {
                        fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE;
                        IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl);
                        fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN;
                } else {
                        IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0);
                        /*
                         * In order to prevent Tx hangs when the internal Tx
                         * switch is enabled we must set the high water mark
                         * to the Rx packet buffer size - 24KB.  This allows
                         * the Tx switch to function even under heavy Rx
                         * workloads.
                         */
                        fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
                }

                IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth);
        }

        /* Configure pause time (2 TCs per register) */
        reg = hw->fc.pause_time * 0x00010001U;
        for (i = 0; i < (MAX_TRAFFIC_CLASS / 2); i++)
                IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg);

        IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2);

        return 0;
}

/**
 *  ixgbe_negotiate_fc - Negotiate flow control
 *  @hw: pointer to hardware structure
 *  @adv_reg: flow control advertised settings
 *  @lp_reg: link partner's flow control settings
 *  @adv_sym: symmetric pause bit in advertisement
 *  @adv_asm: asymmetric pause bit in advertisement
 *  @lp_sym: symmetric pause bit in link partner advertisement
 *  @lp_asm: asymmetric pause bit in link partner advertisement
 *
 *  Find the intersection between advertised settings and link partner's
 *  advertised settings
 **/
int ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
                       u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
{
        if ((!(adv_reg)) ||  (!(lp_reg)))
                return -EINVAL;

        if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
                /*
                 * Now we need to check if the user selected Rx ONLY
                 * of pause frames.  In this case, we had to advertise
                 * FULL flow control because we could not advertise RX
                 * ONLY. Hence, we must now check to see if we need to
                 * turn OFF the TRANSMISSION of PAUSE frames.
                 */
                if (hw->fc.requested_mode == ixgbe_fc_full) {
                        hw->fc.current_mode = ixgbe_fc_full;
                        hw_dbg(hw, "Flow Control = FULL.\n");
                } else {
                        hw->fc.current_mode = ixgbe_fc_rx_pause;
                        hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
                }
        } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
                   (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
                hw->fc.current_mode = ixgbe_fc_tx_pause;
                hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
        } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
                   !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
                hw->fc.current_mode = ixgbe_fc_rx_pause;
                hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
        } else {
                hw->fc.current_mode = ixgbe_fc_none;
                hw_dbg(hw, "Flow Control = NONE.\n");
        }
        return 0;
}

/**
 *  ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber
 *  @hw: pointer to hardware structure
 *
 *  Enable flow control according on 1 gig fiber.
 **/
static int ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw)
{
        u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
        int ret_val;

        /*
         * On multispeed fiber at 1g, bail out if
         * - link is up but AN did not complete, or if
         * - link is up and AN completed but timed out
         */

        linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
        if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
            (!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1))
                return -EIO;

        pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
        pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);

        ret_val =  ixgbe_negotiate_fc(hw, pcs_anadv_reg,
                               pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE,
                               IXGBE_PCS1GANA_ASM_PAUSE,
                               IXGBE_PCS1GANA_SYM_PAUSE,
                               IXGBE_PCS1GANA_ASM_PAUSE);

        return ret_val;
}

/**
 *  ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37
 *  @hw: pointer to hardware structure
 *
 *  Enable flow control according to IEEE clause 37.
 **/
static int ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw)
{
        u32 links2, anlp1_reg, autoc_reg, links;
        int ret_val;

        /*
         * On backplane, bail out if
         * - backplane autoneg was not completed, or if
         * - we are 82599 and link partner is not AN enabled
         */
        links = IXGBE_READ_REG(hw, IXGBE_LINKS);
        if ((links & IXGBE_LINKS_KX_AN_COMP) == 0)
                return -EIO;

        if (hw->mac.type == ixgbe_mac_82599EB) {
                links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
                if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0)
                        return -EIO;
        }
        /*
         * Read the 10g AN autoc and LP ability registers and resolve
         * local flow control settings accordingly
         */
        autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
        anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);

        ret_val = ixgbe_negotiate_fc(hw, autoc_reg,
                anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE,
                IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE);

        return ret_val;
}

/**
 *  ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37
 *  @hw: pointer to hardware structure
 *
 *  Enable flow control according to IEEE clause 37.
 **/
static int ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw)
{
        u16 technology_ability_reg = 0;
        u16 lp_technology_ability_reg = 0;

        hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
                             MDIO_MMD_AN,
                             &technology_ability_reg);
        hw->phy.ops.read_reg(hw, MDIO_AN_LPA,
                             MDIO_MMD_AN,
                             &lp_technology_ability_reg);

        return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg,
                                  (u32)lp_technology_ability_reg,
                                  IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE,
                                  IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE);
}

/**
 *  ixgbe_fc_autoneg - Configure flow control
 *  @hw: pointer to hardware structure
 *
 *  Compares our advertised flow control capabilities to those advertised by
 *  our link partner, and determines the proper flow control mode to use.
 **/
void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
{
        ixgbe_link_speed speed;
        int ret_val = -EIO;
        bool link_up;

        /*
         * AN should have completed when the cable was plugged in.
         * Look for reasons to bail out.  Bail out if:
         * - FC autoneg is disabled, or if
         * - link is not up.
         *
         * Since we're being called from an LSC, link is already known to be up.
         * So use link_up_wait_to_complete=false.
         */
        if (hw->fc.disable_fc_autoneg)
                goto out;

        hw->mac.ops.check_link(hw, &speed, &link_up, false);
        if (!link_up)
                goto out;

        switch (hw->phy.media_type) {
        /* Autoneg flow control on fiber adapters */
        case ixgbe_media_type_fiber:
                if (speed == IXGBE_LINK_SPEED_1GB_FULL)
                        ret_val = ixgbe_fc_autoneg_fiber(hw);
                break;

        /* Autoneg flow control on backplane adapters */
        case ixgbe_media_type_backplane:
                ret_val = ixgbe_fc_autoneg_backplane(hw);
                break;

        /* Autoneg flow control on copper adapters */
        case ixgbe_media_type_copper:
                if (ixgbe_device_supports_autoneg_fc(hw))
                        ret_val = ixgbe_fc_autoneg_copper(hw);
                break;

        default:
                break;
        }

out:
        if (ret_val == 0) {
                hw->fc.fc_was_autonegged = true;
        } else {
                hw->fc.fc_was_autonegged = false;
                hw->fc.current_mode = hw->fc.requested_mode;
        }
}

/**
 * ixgbe_pcie_timeout_poll - Return number of times to poll for completion
 * @hw: pointer to hardware structure
 *
 * System-wide timeout range is encoded in PCIe Device Control2 register.
 *
 *  Add 10% to specified maximum and return the number of times to poll for
 *  completion timeout, in units of 100 microsec.  Never return less than
 *  800 = 80 millisec.
 **/
static u32 ixgbe_pcie_timeout_poll(struct ixgbe_hw *hw)
{
        s16 devctl2;
        u32 pollcnt;

        devctl2 = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_CONTROL2);
        devctl2 &= IXGBE_PCIDEVCTRL2_TIMEO_MASK;

        switch (devctl2) {
        case IXGBE_PCIDEVCTRL2_65_130ms:
                 pollcnt = 1300;         /* 130 millisec */
                break;
        case IXGBE_PCIDEVCTRL2_260_520ms:
                pollcnt = 5200;         /* 520 millisec */
                break;
        case IXGBE_PCIDEVCTRL2_1_2s:
                pollcnt = 20000;        /* 2 sec */
                break;
        case IXGBE_PCIDEVCTRL2_4_8s:
                pollcnt = 80000;        /* 8 sec */
                break;
        case IXGBE_PCIDEVCTRL2_17_34s:
                pollcnt = 34000;        /* 34 sec */
                break;
        case IXGBE_PCIDEVCTRL2_50_100us:        /* 100 microsecs */
        case IXGBE_PCIDEVCTRL2_1_2ms:           /* 2 millisecs */
        case IXGBE_PCIDEVCTRL2_16_32ms:         /* 32 millisec */
        case IXGBE_PCIDEVCTRL2_16_32ms_def:     /* 32 millisec default */
        default:
                pollcnt = 800;          /* 80 millisec minimum */
                break;
        }

        /* add 10% to spec maximum */
        return (pollcnt * 11) / 10;
}

/**
 *  ixgbe_disable_pcie_primary - Disable PCI-express primary access
 *  @hw: pointer to hardware structure
 *
 *  Disables PCI-Express primary access and verifies there are no pending
 *  requests. -EALREADY is returned if primary disable
 *  bit hasn't caused the primary requests to be disabled, else 0
 *  is returned signifying primary requests disabled.
 **/
static int ixgbe_disable_pcie_primary(struct ixgbe_hw *hw)
{
        u32 i, poll;
        u16 value;

        /* Always set this bit to ensure any future transactions are blocked */
        IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS);

        /* Poll for bit to read as set */
        for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
                if (IXGBE_READ_REG(hw, IXGBE_CTRL) & IXGBE_CTRL_GIO_DIS)
                        break;
                usleep_range(100, 120);
        }
        if (i >= IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT) {
                hw_dbg(hw, "GIO disable did not set - requesting resets\n");
                goto gio_disable_fail;
        }

        /* Exit if primary requests are blocked */
        if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) ||
            ixgbe_removed(hw->hw_addr))
                return 0;

        /* Poll for primary request bit to clear */
        for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
                udelay(100);
                if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
                        return 0;
        }

        /*
         * Two consecutive resets are required via CTRL.RST per datasheet
         * 5.2.5.3.2 Primary Disable.  We set a flag to inform the reset routine
         * of this need.  The first reset prevents new primary requests from
         * being issued by our device.  We then must wait 1usec or more for any
         * remaining completions from the PCIe bus to trickle in, and then reset
         * again to clear out any effects they may have had on our device.
         */
        hw_dbg(hw, "GIO Primary Disable bit didn't clear - requesting resets\n");
gio_disable_fail:
        hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;

        if (hw->mac.type >= ixgbe_mac_X550)
                return 0;

        /*
         * Before proceeding, make sure that the PCIe block does not have
         * transactions pending.
         */
        poll = ixgbe_pcie_timeout_poll(hw);
        for (i = 0; i < poll; i++) {
                udelay(100);
                value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
                if (ixgbe_removed(hw->hw_addr))
                        return 0;
                if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
                        return 0;
        }

        hw_dbg(hw, "PCIe transaction pending bit also did not clear.\n");
        return -EALREADY;
}

/**
 *  ixgbe_acquire_swfw_sync - Acquire SWFW semaphore
 *  @hw: pointer to hardware structure
 *  @mask: Mask to specify which semaphore to acquire
 *
 *  Acquires the SWFW semaphore through the GSSR register for the specified
 *  function (CSR, PHY0, PHY1, EEPROM, Flash)
 **/
int ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u32 mask)
{
        u32 gssr = 0;
        u32 swmask = mask;
        u32 fwmask = mask << 5;
        u32 timeout = 200;
        u32 i;

        for (i = 0; i < timeout; i++) {
                /*
                 * SW NVM semaphore bit is used for access to all
                 * SW_FW_SYNC bits (not just NVM)
                 */
                if (ixgbe_get_eeprom_semaphore(hw))
                        return -EBUSY;

                gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
                if (!(gssr & (fwmask | swmask))) {
                        gssr |= swmask;
                        IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);
                        ixgbe_release_eeprom_semaphore(hw);
                        return 0;
                } else {
                        /* Resource is currently in use by FW or SW */
                        ixgbe_release_eeprom_semaphore(hw);
                        usleep_range(5000, 10000);
                }
        }

        /* If time expired clear the bits holding the lock and retry */
        if (gssr & (fwmask | swmask))
                ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask));

        usleep_range(5000, 10000);
        return -EBUSY;
}

/**
 *  ixgbe_release_swfw_sync - Release SWFW semaphore
 *  @hw: pointer to hardware structure
 *  @mask: Mask to specify which semaphore to release
 *
 *  Releases the SWFW semaphore through the GSSR register for the specified
 *  function (CSR, PHY0, PHY1, EEPROM, Flash)
 **/
void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u32 mask)
{
        u32 gssr;
        u32 swmask = mask;

        ixgbe_get_eeprom_semaphore(hw);

        gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
        gssr &= ~swmask;
        IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);

        ixgbe_release_eeprom_semaphore(hw);
}

/**
 * prot_autoc_read_generic - Hides MAC differences needed for AUTOC read
 * @hw: pointer to hardware structure
 * @reg_val: Value we read from AUTOC
 * @locked: bool to indicate whether the SW/FW lock should be taken.  Never
 *          true in this the generic case.
 *
 * The default case requires no protection so just to the register read.
 **/
int prot_autoc_read_generic(struct ixgbe_hw *hw, bool *locked, u32 *reg_val)
{
        *locked = false;
        *reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC);
        return 0;
}

/**
 * prot_autoc_write_generic - Hides MAC differences needed for AUTOC write
 * @hw: pointer to hardware structure
 * @reg_val: value to write to AUTOC
 * @locked: bool to indicate whether the SW/FW lock was already taken by
 *          previous read.
 **/
int prot_autoc_write_generic(struct ixgbe_hw *hw, u32 reg_val, bool locked)
{
        IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_val);
        return 0;
}

/**
 *  ixgbe_disable_rx_buff_generic - Stops the receive data path
 *  @hw: pointer to hardware structure
 *
 *  Stops the receive data path and waits for the HW to internally
 *  empty the Rx security block.
 **/
int ixgbe_disable_rx_buff_generic(struct ixgbe_hw *hw)
{
#define IXGBE_MAX_SECRX_POLL 40
        int i;
        int secrxreg;

        secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
        secrxreg |= IXGBE_SECRXCTRL_RX_DIS;
        IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
        for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) {
                secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT);
                if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY)
                        break;
                else
                        /* Use interrupt-safe sleep just in case */
                        udelay(1000);
        }

        /* For informational purposes only */
        if (i >= IXGBE_MAX_SECRX_POLL)
                hw_dbg(hw, "Rx unit being enabled before security path fully disabled. Continuing with init.\n");

        return 0;

}

/**
 *  ixgbe_enable_rx_buff_generic - Enables the receive data path
 *  @hw: pointer to hardware structure
 *
 *  Enables the receive data path
 **/
int ixgbe_enable_rx_buff_generic(struct ixgbe_hw *hw)
{
        u32 secrxreg;

        secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
        secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS;
        IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
        IXGBE_WRITE_FLUSH(hw);

        return 0;
}

/**
 *  ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit
 *  @hw: pointer to hardware structure
 *  @regval: register value to write to RXCTRL
 *
 *  Enables the Rx DMA unit
 **/
int ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval)
{
        if (regval & IXGBE_RXCTRL_RXEN)
                hw->mac.ops.enable_rx(hw);
        else
                hw->mac.ops.disable_rx(hw);

        return 0;
}

/**
 *  ixgbe_blink_led_start_generic - Blink LED based on index.
 *  @hw: pointer to hardware structure
 *  @index: led number to blink
 **/
int ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index)
{
        u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
        u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
        ixgbe_link_speed speed = 0;
        bool link_up = false;
        bool locked = false;
        int ret_val;

        if (index > 3)
                return -EINVAL;

        /*
         * Link must be up to auto-blink the LEDs;
         * Force it if link is down.
         */
        hw->mac.ops.check_link(hw, &speed, &link_up, false);

        if (!link_up) {
                ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
                if (ret_val)
                        return ret_val;

                autoc_reg |= IXGBE_AUTOC_AN_RESTART;
                autoc_reg |= IXGBE_AUTOC_FLU;

                ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
                if (ret_val)
                        return ret_val;

                IXGBE_WRITE_FLUSH(hw);

                usleep_range(10000, 20000);
        }

        led_reg &= ~IXGBE_LED_MODE_MASK(index);
        led_reg |= IXGBE_LED_BLINK(index);
        IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
        IXGBE_WRITE_FLUSH(hw);

        return 0;
}

/**
 *  ixgbe_blink_led_stop_generic - Stop blinking LED based on index.
 *  @hw: pointer to hardware structure
 *  @index: led number to stop blinking
 **/
int ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index)
{
        u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
        bool locked = false;
        u32 autoc_reg = 0;
        int ret_val;

        if (index > 3)
                return -EINVAL;

        ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
        if (ret_val)
                return ret_val;

        autoc_reg &= ~IXGBE_AUTOC_FLU;
        autoc_reg |= IXGBE_AUTOC_AN_RESTART;

        ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
        if (ret_val)
                return ret_val;

        led_reg &= ~IXGBE_LED_MODE_MASK(index);
        led_reg &= ~IXGBE_LED_BLINK(index);
        led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
        IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
        IXGBE_WRITE_FLUSH(hw);

        return 0;
}

/**
 *  ixgbe_get_san_mac_addr_offset - Get SAN MAC address offset from the EEPROM
 *  @hw: pointer to hardware structure
 *  @san_mac_offset: SAN MAC address offset
 *
 *  This function will read the EEPROM location for the SAN MAC address
 *  pointer, and returns the value at that location.  This is used in both
 *  get and set mac_addr routines.
 **/
static int ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw,
                                         u16 *san_mac_offset)
{
        int ret_val;

        /*
         * First read the EEPROM pointer to see if the MAC addresses are
         * available.
         */
        ret_val = hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR,
                                      san_mac_offset);
        if (ret_val)
                hw_err(hw, "eeprom read at offset %d failed\n",
                       IXGBE_SAN_MAC_ADDR_PTR);

        return ret_val;
}

/**
 *  ixgbe_get_san_mac_addr_generic - SAN MAC address retrieval from the EEPROM
 *  @hw: pointer to hardware structure
 *  @san_mac_addr: SAN MAC address
 *
 *  Reads the SAN MAC address from the EEPROM, if it's available.  This is
 *  per-port, so set_lan_id() must be called before reading the addresses.
 *  set_lan_id() is called by identify_sfp(), but this cannot be relied
 *  upon for non-SFP connections, so we must call it here.
 **/
int ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr)
{
        u16 san_mac_data, san_mac_offset;
        int ret_val;
        u8 i;

        /*
         * First read the EEPROM pointer to see if the MAC addresses are
         * available.  If they're not, no point in calling set_lan_id() here.
         */
        ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset);
        if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF)

                goto san_mac_addr_clr;

        /* make sure we know which port we need to program */
        hw->mac.ops.set_lan_id(hw);
        /* apply the port offset to the address offset */
        (hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) :
                         (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET);
        for (i = 0; i < 3; i++) {
                ret_val = hw->eeprom.ops.read(hw, san_mac_offset,
                                              &san_mac_data);
                if (ret_val) {
                        hw_err(hw, "eeprom read at offset %d failed\n",
                               san_mac_offset);
                        goto san_mac_addr_clr;
                }
                san_mac_addr[i * 2] = (u8)(san_mac_data);
                san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8);
                san_mac_offset++;
        }
        return 0;

san_mac_addr_clr:
        /* No addresses available in this EEPROM.  It's not necessarily an
         * error though, so just wipe the local address and return.
         */
        for (i = 0; i < 6; i++)
                san_mac_addr[i] = 0xFF;
        return ret_val;
}

/**
 *  ixgbe_get_pcie_msix_count_generic - Gets MSI-X vector count
 *  @hw: pointer to hardware structure
 *
 *  Read PCIe configuration space, and get the MSI-X vector count from
 *  the capabilities table.
 **/
u16 ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw *hw)
{
        u16 msix_count;
        u16 max_msix_count;
        u16 pcie_offset;

        switch (hw->mac.type) {
        case ixgbe_mac_82598EB:
                pcie_offset = IXGBE_PCIE_MSIX_82598_CAPS;
                max_msix_count = IXGBE_MAX_MSIX_VECTORS_82598;
                break;
        case ixgbe_mac_82599EB:
        case ixgbe_mac_X540:
        case ixgbe_mac_X550:
        case ixgbe_mac_X550EM_x:
        case ixgbe_mac_x550em_a:
                pcie_offset = IXGBE_PCIE_MSIX_82599_CAPS;
                max_msix_count = IXGBE_MAX_MSIX_VECTORS_82599;
                break;
        default:
                return 1;
        }

        msix_count = ixgbe_read_pci_cfg_word(hw, pcie_offset);
        if (ixgbe_removed(hw->hw_addr))
                msix_count = 0;
        msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK;

        /* MSI-X count is zero-based in HW */
        msix_count++;

        if (msix_count > max_msix_count)
                msix_count = max_msix_count;

        return msix_count;
}

/**
 *  ixgbe_clear_vmdq_generic - Disassociate a VMDq pool index from a rx address
 *  @hw: pointer to hardware struct
 *  @rar: receive address register index to disassociate
 *  @vmdq: VMDq pool index to remove from the rar
 **/
int ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
{
        u32 mpsar_lo, mpsar_hi;
        u32 rar_entries = hw->mac.num_rar_entries;

        /* Make sure we are using a valid rar index range */
        if (rar >= rar_entries) {
                hw_dbg(hw, "RAR index %d is out of range.\n", rar);
                return -EINVAL;
        }

        mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
        mpsar_hi = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));

        if (ixgbe_removed(hw->hw_addr))
                return 0;

        if (!mpsar_lo && !mpsar_hi)
                return 0;

        if (vmdq == IXGBE_CLEAR_VMDQ_ALL) {
                if (mpsar_lo) {
                        IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
                        mpsar_lo = 0;
                }
                if (mpsar_hi) {
                        IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
                        mpsar_hi = 0;
                }
        } else if (vmdq < 32) {
                mpsar_lo &= ~BIT(vmdq);
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar_lo);
        } else {
                mpsar_hi &= ~BIT(vmdq - 32);
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar_hi);
        }

        /* was that the last pool using this rar? */
        if (mpsar_lo == 0 && mpsar_hi == 0 &&
            rar != 0 && rar != hw->mac.san_mac_rar_index)
                hw->mac.ops.clear_rar(hw, rar);

        return 0;
}

/**
 *  ixgbe_set_vmdq_generic - Associate a VMDq pool index with a rx address
 *  @hw: pointer to hardware struct
 *  @rar: receive address register index to associate with a VMDq index
 *  @vmdq: VMDq pool index
 **/
int ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
{
        u32 mpsar;
        u32 rar_entries = hw->mac.num_rar_entries;

        /* Make sure we are using a valid rar index range */
        if (rar >= rar_entries) {
                hw_dbg(hw, "RAR index %d is out of range.\n", rar);
                return -EINVAL;
        }

        if (vmdq < 32) {
                mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
                mpsar |= BIT(vmdq);
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar);
        } else {
                mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));
                mpsar |= BIT(vmdq - 32);
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar);
        }
        return 0;
}

/**
 *  ixgbe_set_vmdq_san_mac_generic - Associate VMDq pool index with a rx address
 *  @hw: pointer to hardware struct
 *  @vmdq: VMDq pool index
 *
 *  This function should only be involved in the IOV mode.
 *  In IOV mode, Default pool is next pool after the number of
 *  VFs advertized and not 0.
 *  MPSAR table needs to be updated for SAN_MAC RAR [hw->mac.san_mac_rar_index]
 **/
int ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw *hw, u32 vmdq)
{
        u32 rar = hw->mac.san_mac_rar_index;

        if (vmdq < 32) {
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), BIT(vmdq));
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
        } else {
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
                IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), BIT(vmdq - 32));
        }

        return 0;
}

/**
 *  ixgbe_init_uta_tables_generic - Initialize the Unicast Table Array
 *  @hw: pointer to hardware structure
 **/
int ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw)
{
        int i;

        for (i = 0; i < 128; i++)
                IXGBE_WRITE_REG(hw, IXGBE_UTA(i), 0);

        return 0;
}

/**
 *  ixgbe_find_vlvf_slot - find the vlanid or the first empty slot
 *  @hw: pointer to hardware structure
 *  @vlan: VLAN id to write to VLAN filter
 *  @vlvf_bypass: true to find vlanid only, false returns first empty slot if
 *                vlanid not found
 *
 *  return the VLVF index where this VLAN id should be placed
 *
 **/
static int ixgbe_find_vlvf_slot(struct ixgbe_hw *hw, u32 vlan, bool vlvf_bypass)
{
        int regindex, first_empty_slot;
        u32 bits;

        /* short cut the special case */
        if (vlan == 0)
                return 0;

        /* if vlvf_bypass is set we don't want to use an empty slot, we
         * will simply bypass the VLVF if there are no entries present in the
         * VLVF that contain our VLAN
         */
        first_empty_slot = vlvf_bypass ? -ENOSPC : 0;

        /* add VLAN enable bit for comparison */
        vlan |= IXGBE_VLVF_VIEN;

        /* Search for the vlan id in the VLVF entries. Save off the first empty
         * slot found along the way.
         *
         * pre-decrement loop covering (IXGBE_VLVF_ENTRIES - 1) .. 1
         */
        for (regindex = IXGBE_VLVF_ENTRIES; --regindex;) {
                bits = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex));
                if (bits == vlan)
                        return regindex;
                if (!first_empty_slot && !bits)
                        first_empty_slot = regindex;
        }

        /* If we are here then we didn't find the VLAN.  Return first empty
         * slot we found during our search, else error.
         */
        if (!first_empty_slot)
                hw_dbg(hw, "No space in VLVF.\n");

        return first_empty_slot ? : -ENOSPC;
}

/**
 *  ixgbe_set_vfta_generic - Set VLAN filter table
 *  @hw: pointer to hardware structure
 *  @vlan: VLAN id to write to VLAN filter
 *  @vind: VMDq output index that maps queue to VLAN id in VFVFB
 *  @vlan_on: boolean flag to turn on/off VLAN in VFVF
 *  @vlvf_bypass: boolean flag indicating updating default pool is okay
 *
 *  Turn on/off specified VLAN in the VLAN filter table.
 **/
int ixgbe_set_vfta_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind,
                           bool vlan_on, bool vlvf_bypass)
{
        u32 regidx, vfta_delta, vfta, bits;
        int vlvf_index;

        if ((vlan > 4095) || (vind > 63))
                return -EINVAL;

        /*
         * this is a 2 part operation - first the VFTA, then the
         * VLVF and VLVFB if VT Mode is set
         * We don't write the VFTA until we know the VLVF part succeeded.
         */

        /* Part 1
         * The VFTA is a bitstring made up of 128 32-bit registers
         * that enable the particular VLAN id, much like the MTA:
         *    bits[11-5]: which register
         *    bits[4-0]:  which bit in the register
         */
        regidx = vlan / 32;
        vfta_delta = BIT(vlan % 32);
        vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regidx));

        /* vfta_delta represents the difference between the current value
         * of vfta and the value we want in the register.  Since the diff
         * is an XOR mask we can just update vfta using an XOR.
         */
        vfta_delta &= vlan_on ? ~vfta : vfta;
        vfta ^= vfta_delta;

        /* Part 2
         * If VT Mode is set
         *   Either vlan_on
         *     make sure the vlan is in VLVF
         *     set the vind bit in the matching VLVFB
         *   Or !vlan_on
         *     clear the pool bit and possibly the vind
         */
        if (!(IXGBE_READ_REG(hw, IXGBE_VT_CTL) & IXGBE_VT_CTL_VT_ENABLE))
                goto vfta_update;

        vlvf_index = ixgbe_find_vlvf_slot(hw, vlan, vlvf_bypass);
        if (vlvf_index < 0) {
                if (vlvf_bypass)
                        goto vfta_update;
                return vlvf_index;
        }

        bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32));

        /* set the pool bit */
        bits |= BIT(vind % 32);
        if (vlan_on)
                goto vlvf_update;

        /* clear the pool bit */
        bits ^= BIT(vind % 32);

        if (!bits &&
            !IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + 1 - vind / 32))) {
                /* Clear VFTA first, then disable VLVF.  Otherwise
                 * we run the risk of stray packets leaking into
                 * the PF via the default pool
                 */
                if (vfta_delta)
                        IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);

                /* disable VLVF and clear remaining bit from pool */
                IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 0);
                IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), 0);

                return 0;
        }

        /* If there are still bits set in the VLVFB registers
         * for the VLAN ID indicated we need to see if the
         * caller is requesting that we clear the VFTA entry bit.
         * If the caller has requested that we clear the VFTA
         * entry bit but there are still pools/VFs using this VLAN
         * ID entry then ignore the request.  We're not worried
         * about the case where we're turning the VFTA VLAN ID
         * entry bit on, only when requested to turn it off as
         * there may be multiple pools and/or VFs using the
         * VLAN ID entry.  In that case we cannot clear the
         * VFTA bit until all pools/VFs using that VLAN ID have also
         * been cleared.  This will be indicated by "bits" being
         * zero.
         */
        vfta_delta = 0;

vlvf_update:
        /* record pool change and enable VLAN ID if not already enabled */
        IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), bits);
        IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), IXGBE_VLVF_VIEN | vlan);

vfta_update:
        /* Update VFTA now that we are ready for traffic */
        if (vfta_delta)
                IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);

        return 0;
}

/**
 *  ixgbe_clear_vfta_generic - Clear VLAN filter table
 *  @hw: pointer to hardware structure
 *
 *  Clears the VLAN filter table, and the VMDq index associated with the filter
 **/
int ixgbe_clear_vfta_generic(struct ixgbe_hw *hw)
{
        u32 offset;

        for (offset = 0; offset < hw->mac.vft_size; offset++)
                IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0);

        for (offset = 0; offset < IXGBE_VLVF_ENTRIES; offset++) {
                IXGBE_WRITE_REG(hw, IXGBE_VLVF(offset), 0);
                IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2), 0);
                IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2 + 1), 0);
        }

        return 0;
}

/**
 *  ixgbe_need_crosstalk_fix - Determine if we need to do cross talk fix
 *  @hw: pointer to hardware structure
 *
 *  Contains the logic to identify if we need to verify link for the
 *  crosstalk fix
 **/
static bool ixgbe_need_crosstalk_fix(struct ixgbe_hw *hw)
{
        /* Does FW say we need the fix */
        if (!hw->need_crosstalk_fix)
                return false;

        /* Only consider SFP+ PHYs i.e. media type fiber */
        switch (hw->mac.ops.get_media_type(hw)) {
        case ixgbe_media_type_fiber:
        case ixgbe_media_type_fiber_qsfp:
                break;
        default:
                return false;
        }

        return true;
}

/**
 *  ixgbe_check_mac_link_generic - Determine link and speed status
 *  @hw: pointer to hardware structure
 *  @speed: pointer to link speed
 *  @link_up: true when link is up
 *  @link_up_wait_to_complete: bool used to wait for link up or not
 *
 *  Reads the links register to determine if link is up and the current speed
 **/
int ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
                                 bool *link_up, bool link_up_wait_to_complete)
{
        bool crosstalk_fix_active = ixgbe_need_crosstalk_fix(hw);
        u32 links_reg, links_orig;
        u32 i;

        /* If Crosstalk fix enabled do the sanity check of making sure
         * the SFP+ cage is full.
         */
        if (crosstalk_fix_active) {
                u32 sfp_cage_full;

                switch (hw->mac.type) {
                case ixgbe_mac_82599EB:
                        sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
                                        IXGBE_ESDP_SDP2;
                        break;
                case ixgbe_mac_X550EM_x:
                case ixgbe_mac_x550em_a:
                        sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
                                        IXGBE_ESDP_SDP0;
                        break;
                default:
                        /* sanity check - No SFP+ devices here */
                        sfp_cage_full = false;
                        break;
                }

                if (!sfp_cage_full) {
                        *link_up = false;
                        *speed = IXGBE_LINK_SPEED_UNKNOWN;
                        return 0;
                }
        }

        /* clear the old state */
        links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS);

        links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);

        if (links_orig != links_reg) {
                hw_dbg(hw, "LINKS changed from %08X to %08X\n",
                       links_orig, links_reg);
        }

        if (link_up_wait_to_complete) {
                for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
                        if (links_reg & IXGBE_LINKS_UP) {
                                *link_up = true;
                                break;
                        } else {
                                *link_up = false;
                        }
                        msleep(100);
                        links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
                }
        } else {
                if (links_reg & IXGBE_LINKS_UP) {
                        if (crosstalk_fix_active) {
                                /* Check the link state again after a delay
                                 * to filter out spurious link up
                                 * notifications.
                                 */
                                mdelay(5);
                                links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
                                if (!(links_reg & IXGBE_LINKS_UP)) {
                                        *link_up = false;
                                        *speed = IXGBE_LINK_SPEED_UNKNOWN;
                                        return 0;
                                }
                        }
                        *link_up = true;
                } else {
                        *link_up = false;
                }
        }

        switch (links_reg & IXGBE_LINKS_SPEED_82599) {
        case IXGBE_LINKS_SPEED_10G_82599:
                if ((hw->mac.type >= ixgbe_mac_X550) &&
                    (links_reg & IXGBE_LINKS_SPEED_NON_STD))
                        *speed = IXGBE_LINK_SPEED_2_5GB_FULL;
                else
                        *speed = IXGBE_LINK_SPEED_10GB_FULL;
                break;
        case IXGBE_LINKS_SPEED_1G_82599:
                *speed = IXGBE_LINK_SPEED_1GB_FULL;
                break;
        case IXGBE_LINKS_SPEED_100_82599:
                if ((hw->mac.type >= ixgbe_mac_X550) &&
                    (links_reg & IXGBE_LINKS_SPEED_NON_STD))
                        *speed = IXGBE_LINK_SPEED_5GB_FULL;
                else
                        *speed = IXGBE_LINK_SPEED_100_FULL;
                break;
        case IXGBE_LINKS_SPEED_10_X550EM_A:
                *speed = IXGBE_LINK_SPEED_UNKNOWN;
                if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
                    hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
                        *speed = IXGBE_LINK_SPEED_10_FULL;
                }
                break;
        default:
                *speed = IXGBE_LINK_SPEED_UNKNOWN;
        }

        return 0;
}

/**
 *  ixgbe_get_wwn_prefix_generic - Get alternative WWNN/WWPN prefix from
 *  the EEPROM
 *  @hw: pointer to hardware structure
 *  @wwnn_prefix: the alternative WWNN prefix
 *  @wwpn_prefix: the alternative WWPN prefix
 *
 *  This function will read the EEPROM from the alternative SAN MAC address
 *  block to check the support for the alternative WWNN/WWPN prefix support.
 **/
int ixgbe_get_wwn_prefix_generic(struct ixgbe_hw *hw, u16 *wwnn_prefix,
                                 u16 *wwpn_prefix)
{
        u16 offset, caps;
        u16 alt_san_mac_blk_offset;

        /* clear output first */
        *wwnn_prefix = 0xFFFF;
        *wwpn_prefix = 0xFFFF;

        /* check if alternative SAN MAC is supported */
        offset = IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR;
        if (hw->eeprom.ops.read(hw, offset, &alt_san_mac_blk_offset))
                goto wwn_prefix_err;

        if ((alt_san_mac_blk_offset == 0) ||
            (alt_san_mac_blk_offset == 0xFFFF))
                return 0;

        /* check capability in alternative san mac address block */
        offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET;
        if (hw->eeprom.ops.read(hw, offset, &caps))
                goto wwn_prefix_err;
        if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN))
                return 0;

        /* get the corresponding prefix for WWNN/WWPN */
        offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET;
        if (hw->eeprom.ops.read(hw, offset, wwnn_prefix))
                hw_err(hw, "eeprom read at offset %d failed\n", offset);

        offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET;
        if (hw->eeprom.ops.read(hw, offset, wwpn_prefix))
                goto wwn_prefix_err;

        return 0;

wwn_prefix_err:
        hw_err(hw, "eeprom read at offset %d failed\n", offset);
        return 0;
}

/**
 *  ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing
 *  @hw: pointer to hardware structure
 *  @enable: enable or disable switch for MAC anti-spoofing
 *  @vf: Virtual Function pool - VF Pool to set for MAC anti-spoofing
 *
 **/
void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
{
        int vf_target_reg = vf >> 3;
        int vf_target_shift = vf % 8;
        u32 pfvfspoof;

        if (hw->mac.type == ixgbe_mac_82598EB)
                return;

        pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
        if (enable)
                pfvfspoof |= BIT(vf_target_shift);
        else
                pfvfspoof &= ~BIT(vf_target_shift);
        IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
}

/**
 *  ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing
 *  @hw: pointer to hardware structure
 *  @enable: enable or disable switch for VLAN anti-spoofing
 *  @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing
 *
 **/
void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
{
        int vf_target_reg = vf >> 3;
        int vf_target_shift = vf % 8 + IXGBE_SPOOF_VLANAS_SHIFT;
        u32 pfvfspoof;

        if (hw->mac.type == ixgbe_mac_82598EB)
                return;

        pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
        if (enable)
                pfvfspoof |= BIT(vf_target_shift);
        else
                pfvfspoof &= ~BIT(vf_target_shift);
        IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
}

/**
 *  ixgbe_get_device_caps_generic - Get additional device capabilities
 *  @hw: pointer to hardware structure
 *  @device_caps: the EEPROM word with the extra device capabilities
 *
 *  This function will read the EEPROM location for the device capabilities,
 *  and return the word through device_caps.
 **/
int ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps)
{
        hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps);

        return 0;
}

/**
 * ixgbe_set_rxpba_generic - Initialize RX packet buffer
 * @hw: pointer to hardware structure
 * @num_pb: number of packet buffers to allocate
 * @headroom: reserve n KB of headroom
 * @strategy: packet buffer allocation strategy
 **/
void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw,
                             int num_pb,
                             u32 headroom,
                             int strategy)
{
        u32 pbsize = hw->mac.rx_pb_size;
        int i = 0;
        u32 rxpktsize, txpktsize, txpbthresh;

        /* Reserve headroom */
        pbsize -= headroom;

        if (!num_pb)
                num_pb = 1;

        /* Divide remaining packet buffer space amongst the number
         * of packet buffers requested using supplied strategy.
         */
        switch (strategy) {
        case (PBA_STRATEGY_WEIGHTED):
                /* pba_80_48 strategy weight first half of packet buffer with
                 * 5/8 of the packet buffer space.
                 */
                rxpktsize = ((pbsize * 5 * 2) / (num_pb * 8));
                pbsize -= rxpktsize * (num_pb / 2);
                rxpktsize <<= IXGBE_RXPBSIZE_SHIFT;
                for (; i < (num_pb / 2); i++)
                        IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
                fallthrough; /* configure remaining packet buffers */
        case (PBA_STRATEGY_EQUAL):
                /* Divide the remaining Rx packet buffer evenly among the TCs */
                rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT;
                for (; i < num_pb; i++)
                        IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
                break;
        default:
                break;
        }

        /*
         * Setup Tx packet buffer and threshold equally for all TCs
         * TXPBTHRESH register is set in K so divide by 1024 and subtract
         * 10 since the largest packet we support is just over 9K.
         */
        txpktsize = IXGBE_TXPBSIZE_MAX / num_pb;
        txpbthresh = (txpktsize / 1024) - IXGBE_TXPKT_SIZE_MAX;
        for (i = 0; i < num_pb; i++) {
                IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), txpktsize);
                IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), txpbthresh);
        }

        /* Clear unused TCs, if any, to zero buffer size*/
        for (; i < IXGBE_MAX_PB; i++) {
                IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0);
                IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), 0);
                IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), 0);
        }
}

/**
 *  ixgbe_calculate_checksum - Calculate checksum for buffer
 *  @buffer: pointer to EEPROM
 *  @length: size of EEPROM to calculate a checksum for
 *
 *  Calculates the checksum for some buffer on a specified length.  The
 *  checksum calculated is returned.
 **/
u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
{
        u32 i;
        u8 sum = 0;

        if (!buffer)
                return 0;

        for (i = 0; i < length; i++)
                sum += buffer[i];

        return (u8) (0 - sum);
}

/**
 *  ixgbe_hic_unlocked - Issue command to manageability block unlocked
 *  @hw: pointer to the HW structure
 *  @buffer: command to write and where the return status will be placed
 *  @length: length of buffer, must be multiple of 4 bytes
 *  @timeout: time in ms to wait for command completion
 *
 *  Communicates with the manageability block. On success return 0
 *  else returns semaphore error when encountering an error acquiring
 *  semaphore, -EINVAL when incorrect parameters passed or -EIO when
 *  command fails.
 *
 *  This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
 *  by the caller.
 **/
int ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length,
                       u32 timeout)
{
        u32 hicr, i, fwsts;
        u16 dword_len;

        if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
                hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
                return -EINVAL;
        }

        /* Set bit 9 of FWSTS clearing FW reset indication */
        fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS);
        IXGBE_WRITE_REG(hw, IXGBE_FWSTS, fwsts | IXGBE_FWSTS_FWRI);

        /* Check that the host interface is enabled. */
        hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
        if (!(hicr & IXGBE_HICR_EN)) {
                hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n");
                return -EIO;
        }

        /* Calculate length in DWORDs. We must be DWORD aligned */
        if (length % sizeof(u32)) {
                hw_dbg(hw, "Buffer length failure, not aligned to dword");
                return -EINVAL;
        }

        dword_len = length >> 2;

        /* The device driver writes the relevant command block
         * into the ram area.
         */
        for (i = 0; i < dword_len; i++)
                IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG,
                                      i, (__force u32)cpu_to_le32(buffer[i]));

        /* Setting this bit tells the ARC that a new command is pending. */
        IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C);

        for (i = 0; i < timeout; i++) {
                hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
                if (!(hicr & IXGBE_HICR_C))
                        break;
                usleep_range(1000, 2000);
        }

        /* Check command successful completion. */
        if ((timeout && i == timeout) ||
            !(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV))
                return -EIO;

        return 0;
}

/**
 *  ixgbe_host_interface_command - Issue command to manageability block
 *  @hw: pointer to the HW structure
 *  @buffer: contains the command to write and where the return status will
 *           be placed
 *  @length: length of buffer, must be multiple of 4 bytes
 *  @timeout: time in ms to wait for command completion
 *  @return_data: read and return data from the buffer (true) or not (false)
 *  Needed because FW structures are big endian and decoding of
 *  these fields can be 8 bit or 16 bit based on command. Decoding
 *  is not easily understood without making a table of commands.
 *  So we will leave this up to the caller to read back the data
 *  in these cases.
 *
 *  Communicates with the manageability block.  On success return 0
 *  else return -EIO or -EINVAL.
 **/
int ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
                                 u32 length, u32 timeout,
                                 bool return_data)
{
        u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
        struct ixgbe_hic_hdr *hdr = buffer;
        u16 buf_len, dword_len;
        u32 *u32arr = buffer;
        int status;
        u32 bi;

        if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
                hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
                return -EINVAL;
        }
        /* Take management host interface semaphore */
        status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
        if (status)
                return status;

        status = ixgbe_hic_unlocked(hw, buffer, length, timeout);
        if (status)
                goto rel_out;

        if (!return_data)
                goto rel_out;

        /* Calculate length in DWORDs */
        dword_len = hdr_size >> 2;

        /* first pull in the header so we know the buffer length */
        for (bi = 0; bi < dword_len; bi++) {
                u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
                le32_to_cpus(&u32arr[bi]);
        }

        /* If there is any thing in data position pull it in */
        buf_len = hdr->buf_len;
        if (!buf_len)
                goto rel_out;

        if (length < round_up(buf_len, 4) + hdr_size) {
                hw_dbg(hw, "Buffer not large enough for reply message.\n");
                status = -EIO;
                goto rel_out;
        }

        /* Calculate length in DWORDs, add 3 for odd lengths */
        dword_len = (buf_len + 3) >> 2;

        /* Pull in the rest of the buffer (bi is where we left off) */
        for (; bi <= dword_len; bi++) {
                u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
                le32_to_cpus(&u32arr[bi]);
        }

rel_out:
        hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);

        return status;
}

/**
 *  ixgbe_set_fw_drv_ver_generic - Sends driver version to firmware
 *  @hw: pointer to the HW structure
 *  @maj: driver version major number
 *  @min: driver version minor number
 *  @build: driver version build number
 *  @sub: driver version sub build number
 *  @len: length of driver_ver string
 *  @driver_ver: driver string
 *
 *  Sends driver version number to firmware through the manageability
 *  block.  On success return 0
 *  else returns -EBUSY when encountering an error acquiring
 *  semaphore or -EIO when command fails.
 **/
int ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
                                 u8 build, u8 sub, __always_unused u16 len,
                                 __always_unused const char *driver_ver)
{
        struct ixgbe_hic_drv_info fw_cmd;
        int ret_val;
        int i;

        fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
        fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN;
        fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
        fw_cmd.port_num = hw->bus.func;
        fw_cmd.ver_maj = maj;
        fw_cmd.ver_min = min;
        fw_cmd.ver_build = build;
        fw_cmd.ver_sub = sub;
        fw_cmd.hdr.checksum = 0;
        fw_cmd.pad = 0;
        fw_cmd.pad2 = 0;
        fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
                                (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));

        for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
                ret_val = ixgbe_host_interface_command(hw, &fw_cmd,
                                                       sizeof(fw_cmd),
                                                       IXGBE_HI_COMMAND_TIMEOUT,
                                                       true);
                if (ret_val != 0)
                        continue;

                if (fw_cmd.hdr.cmd_or_resp.ret_status ==
                    FW_CEM_RESP_STATUS_SUCCESS)
                        ret_val = 0;
                else
                        ret_val = -EIO;

                break;
        }

        return ret_val;
}

/**
 * ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo
 * @hw: pointer to the hardware structure
 *
 * The 82599 and x540 MACs can experience issues if TX work is still pending
 * when a reset occurs.  This function prevents this by flushing the PCIe
 * buffers on the system.
 **/
void ixgbe_clear_tx_pending(struct ixgbe_hw *hw)
{
        u32 gcr_ext, hlreg0, i, poll;
        u16 value;

        /*
         * If double reset is not requested then all transactions should
         * already be clear and as such there is no work to do
         */
        if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED))
                return;

        /*
         * Set loopback enable to prevent any transmits from being sent
         * should the link come up.  This assumes that the RXCTRL.RXEN bit
         * has already been cleared.
         */
        hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
        IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK);

        /* wait for a last completion before clearing buffers */
        IXGBE_WRITE_FLUSH(hw);
        usleep_range(3000, 6000);

        /* Before proceeding, make sure that the PCIe block does not have
         * transactions pending.
         */
        poll = ixgbe_pcie_timeout_poll(hw);
        for (i = 0; i < poll; i++) {
                usleep_range(100, 200);
                value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
                if (ixgbe_removed(hw->hw_addr))
                        break;
                if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
                        break;
        }

        /* initiate cleaning flow for buffers in the PCIe transaction layer */
        gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT);
        IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT,
                        gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR);

        /* Flush all writes and allow 20usec for all transactions to clear */
        IXGBE_WRITE_FLUSH(hw);
        udelay(20);

        /* restore previous register values */
        IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext);
        IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
}

static const u8 ixgbe_emc_temp_data[4] = {
        IXGBE_EMC_INTERNAL_DATA,
        IXGBE_EMC_DIODE1_DATA,
        IXGBE_EMC_DIODE2_DATA,
        IXGBE_EMC_DIODE3_DATA
};
static const u8 ixgbe_emc_therm_limit[4] = {
        IXGBE_EMC_INTERNAL_THERM_LIMIT,
        IXGBE_EMC_DIODE1_THERM_LIMIT,
        IXGBE_EMC_DIODE2_THERM_LIMIT,
        IXGBE_EMC_DIODE3_THERM_LIMIT
};

/**
 *  ixgbe_get_ets_data - Extracts the ETS bit data
 *  @hw: pointer to hardware structure
 *  @ets_cfg: extected ETS data
 *  @ets_offset: offset of ETS data
 *
 *  Returns error code.
 **/
static int ixgbe_get_ets_data(struct ixgbe_hw *hw, u16 *ets_cfg,
                              u16 *ets_offset)
{
        int status;

        status = hw->eeprom.ops.read(hw, IXGBE_ETS_CFG, ets_offset);
        if (status)
                return status;

        if ((*ets_offset == 0x0000) || (*ets_offset == 0xFFFF))
                return -EOPNOTSUPP;

        status = hw->eeprom.ops.read(hw, *ets_offset, ets_cfg);
        if (status)
                return status;

        if ((*ets_cfg & IXGBE_ETS_TYPE_MASK) != IXGBE_ETS_TYPE_EMC_SHIFTED)
                return -EOPNOTSUPP;

        return 0;
}

/**
 *  ixgbe_get_thermal_sensor_data_generic - Gathers thermal sensor data
 *  @hw: pointer to hardware structure
 *
 *  Returns the thermal sensor data structure
 **/
int ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw *hw)
{
        u16 ets_offset;
        u16 ets_sensor;
        u8  num_sensors;
        u16 ets_cfg;
        int status;
        u8  i;
        struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;

        /* Only support thermal sensors attached to physical port 0 */
        if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
                return -EOPNOTSUPP;

        status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
        if (status)
                return status;

        num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
        if (num_sensors > IXGBE_MAX_SENSORS)
                num_sensors = IXGBE_MAX_SENSORS;

        for (i = 0; i < num_sensors; i++) {
                u8  sensor_index;
                u8  sensor_location;

                status = hw->eeprom.ops.read(hw, (ets_offset + 1 + i),
                                             &ets_sensor);
                if (status)
                        return status;

                sensor_index = FIELD_GET(IXGBE_ETS_DATA_INDEX_MASK,
                                         ets_sensor);
                sensor_location = FIELD_GET(IXGBE_ETS_DATA_LOC_MASK,
                                            ets_sensor);

                if (sensor_location != 0) {
                        status = hw->phy.ops.read_i2c_byte(hw,
                                        ixgbe_emc_temp_data[sensor_index],
                                        IXGBE_I2C_THERMAL_SENSOR_ADDR,
                                        &data->sensor[i].temp);
                        if (status)
                                return status;
                }
        }

        return 0;
}

/**
 * ixgbe_init_thermal_sensor_thresh_generic - Inits thermal sensor thresholds
 * @hw: pointer to hardware structure
 *
 * Inits the thermal sensor thresholds according to the NVM map
 * and save off the threshold and location values into mac.thermal_sensor_data
 **/
int ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw *hw)
{
        struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
        u8  low_thresh_delta;
        u8  num_sensors;
        u8  therm_limit;
        u16 ets_sensor;
        u16 ets_offset;
        u16 ets_cfg;
        int status;
        u8  i;

        memset(data, 0, sizeof(struct ixgbe_thermal_sensor_data));

        /* Only support thermal sensors attached to physical port 0 */
        if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
                return -EOPNOTSUPP;

        status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
        if (status)
                return status;

        low_thresh_delta = FIELD_GET(IXGBE_ETS_LTHRES_DELTA_MASK, ets_cfg);
        num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
        if (num_sensors > IXGBE_MAX_SENSORS)
                num_sensors = IXGBE_MAX_SENSORS;

        for (i = 0; i < num_sensors; i++) {
                u8  sensor_index;
                u8  sensor_location;

                if (hw->eeprom.ops.read(hw, ets_offset + 1 + i, &ets_sensor)) {
                        hw_err(hw, "eeprom read at offset %d failed\n",
                               ets_offset + 1 + i);
                        continue;
                }
                sensor_index = FIELD_GET(IXGBE_ETS_DATA_INDEX_MASK,
                                         ets_sensor);
                sensor_location = FIELD_GET(IXGBE_ETS_DATA_LOC_MASK,
                                            ets_sensor);
                therm_limit = ets_sensor & IXGBE_ETS_DATA_HTHRESH_MASK;

                hw->phy.ops.write_i2c_byte(hw,
                        ixgbe_emc_therm_limit[sensor_index],
                        IXGBE_I2C_THERMAL_SENSOR_ADDR, therm_limit);

                if (sensor_location == 0)
                        continue;

                data->sensor[i].location = sensor_location;
                data->sensor[i].caution_thresh = therm_limit;
                data->sensor[i].max_op_thresh = therm_limit - low_thresh_delta;
        }

        return 0;
}

/**
 *  ixgbe_get_orom_version - Return option ROM from EEPROM
 *
 *  @hw: pointer to hardware structure
 *  @nvm_ver: pointer to output structure
 *
 *  if valid option ROM version, nvm_ver->or_valid set to true
 *  else nvm_ver->or_valid is false.
 **/
void ixgbe_get_orom_version(struct ixgbe_hw *hw,
                            struct ixgbe_nvm_version *nvm_ver)
{
        u16 offset, eeprom_cfg_blkh, eeprom_cfg_blkl;

        nvm_ver->or_valid = false;
        /* Option Rom may or may not be present.  Start with pointer */
        hw->eeprom.ops.read(hw, NVM_OROM_OFFSET, &offset);

        /* make sure offset is valid */
        if (offset == 0x0 || offset == NVM_INVALID_PTR)
                return;

        hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_HI, &eeprom_cfg_blkh);
        hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_LOW, &eeprom_cfg_blkl);

        /* option rom exists and is valid */
        if ((eeprom_cfg_blkl | eeprom_cfg_blkh) == 0x0 ||
            eeprom_cfg_blkl == NVM_VER_INVALID ||
            eeprom_cfg_blkh == NVM_VER_INVALID)
                return;

        nvm_ver->or_valid = true;
        nvm_ver->or_major = eeprom_cfg_blkl >> NVM_OROM_SHIFT;
        nvm_ver->or_build = (eeprom_cfg_blkl << NVM_OROM_SHIFT) |
                            (eeprom_cfg_blkh >> NVM_OROM_SHIFT);
        nvm_ver->or_patch = eeprom_cfg_blkh & NVM_OROM_PATCH_MASK;
}

/**
 *  ixgbe_get_oem_prod_version - Etrack ID from EEPROM
 *  @hw: pointer to hardware structure
 *  @nvm_ver: pointer to output structure
 *
 *  if valid OEM product version, nvm_ver->oem_valid set to true
 *  else nvm_ver->oem_valid is false.
 **/
void ixgbe_get_oem_prod_version(struct ixgbe_hw *hw,
                                struct ixgbe_nvm_version *nvm_ver)
{
        u16 rel_num, prod_ver, mod_len, cap, offset;

        nvm_ver->oem_valid = false;
        hw->eeprom.ops.read(hw, NVM_OEM_PROD_VER_PTR, &offset);

        /* Return is offset to OEM Product Version block is invalid */
        if (offset == 0x0 || offset == NVM_INVALID_PTR)
                return;

        /* Read product version block */
        hw->eeprom.ops.read(hw, offset, &mod_len);
        hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_CAP_OFF, &cap);

        /* Return if OEM product version block is invalid */
        if (mod_len != NVM_OEM_PROD_VER_MOD_LEN ||
            (cap & NVM_OEM_PROD_VER_CAP_MASK) != 0x0)
                return;

        hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_L, &prod_ver);
        hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_H, &rel_num);

        /* Return if version is invalid */
        if ((rel_num | prod_ver) == 0x0 ||
            rel_num == NVM_VER_INVALID || prod_ver == NVM_VER_INVALID)
                return;

        nvm_ver->oem_major = prod_ver >> NVM_VER_SHIFT;
        nvm_ver->oem_minor = prod_ver & NVM_VER_MASK;
        nvm_ver->oem_release = rel_num;
        nvm_ver->oem_valid = true;
}

/**
 *  ixgbe_get_etk_id - Return Etrack ID from EEPROM
 *
 *  @hw: pointer to hardware structure
 *  @nvm_ver: pointer to output structure
 *
 *  word read errors will return 0xFFFF
 **/
void ixgbe_get_etk_id(struct ixgbe_hw *hw,
                      struct ixgbe_nvm_version *nvm_ver)
{
        u16 etk_id_l, etk_id_h;

        if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_LOW, &etk_id_l))
                etk_id_l = NVM_VER_INVALID;
        if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_HI, &etk_id_h))
                etk_id_h = NVM_VER_INVALID;

        /* The word order for the version format is determined by high order
         * word bit 15.
         */
        if ((etk_id_h & NVM_ETK_VALID) == 0) {
                nvm_ver->etk_id = etk_id_h;
                nvm_ver->etk_id |= (etk_id_l << NVM_ETK_SHIFT);
        } else {
                nvm_ver->etk_id = etk_id_l;
                nvm_ver->etk_id |= (etk_id_h << NVM_ETK_SHIFT);
        }
}

void ixgbe_disable_rx_generic(struct ixgbe_hw *hw)
{
        u32 rxctrl;

        rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
        if (rxctrl & IXGBE_RXCTRL_RXEN) {
                if (hw->mac.type != ixgbe_mac_82598EB) {
                        u32 pfdtxgswc;

                        pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
                        if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) {
                                pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN;
                                IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
                                hw->mac.set_lben = true;
                        } else {
                                hw->mac.set_lben = false;
                        }
                }
                rxctrl &= ~IXGBE_RXCTRL_RXEN;
                IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl);
        }
}

void ixgbe_enable_rx_generic(struct ixgbe_hw *hw)
{
        u32 rxctrl;

        rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
        IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, (rxctrl | IXGBE_RXCTRL_RXEN));

        if (hw->mac.type != ixgbe_mac_82598EB) {
                if (hw->mac.set_lben) {
                        u32 pfdtxgswc;

                        pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
                        pfdtxgswc |= IXGBE_PFDTXGSWC_VT_LBEN;
                        IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
                        hw->mac.set_lben = false;
                }
        }
}

/** ixgbe_mng_present - returns true when management capability is present
 * @hw: pointer to hardware structure
 **/
bool ixgbe_mng_present(struct ixgbe_hw *hw)
{
        u32 fwsm;

        if (hw->mac.type < ixgbe_mac_82599EB)
                return false;

        fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM(hw));

        return !!(fwsm & IXGBE_FWSM_FW_MODE_PT);
}

/**
 *  ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
 *  @hw: pointer to hardware structure
 *  @speed: new link speed
 *  @autoneg_wait_to_complete: true when waiting for completion is needed
 *
 *  Set the link speed in the MAC and/or PHY register and restarts link.
 */
int ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
                                          ixgbe_link_speed speed,
                                          bool autoneg_wait_to_complete)
{
        ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
        ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
        bool autoneg, link_up = false;
        u32 speedcnt = 0;
        int status = 0;
        u32 i = 0;

        /* Mask off requested but non-supported speeds */
        status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
        if (status)
                return status;

        speed &= link_speed;

        /* Try each speed one by one, highest priority first.  We do this in
         * software because 10Gb fiber doesn't support speed autonegotiation.
         */
        if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
                speedcnt++;
                highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;

                /* Set the module link speed */
                switch (hw->phy.media_type) {
                case ixgbe_media_type_fiber:
                        hw->mac.ops.set_rate_select_speed(hw,
                                                    IXGBE_LINK_SPEED_10GB_FULL);
                        break;
                case ixgbe_media_type_fiber_qsfp:
                        /* QSFP module automatically detects MAC link speed */
                        break;
                default:
                        hw_dbg(hw, "Unexpected media type\n");
                        break;
                }

                /* Allow module to change analog characteristics (1G->10G) */
                msleep(40);

                status = hw->mac.ops.setup_mac_link(hw,
                                                    IXGBE_LINK_SPEED_10GB_FULL,
                                                    autoneg_wait_to_complete);
                if (status)
                        return status;

                /* Flap the Tx laser if it has not already been done */
                if (hw->mac.ops.flap_tx_laser)
                        hw->mac.ops.flap_tx_laser(hw);

                /* Wait for the controller to acquire link.  Per IEEE 802.3ap,
                 * Section 73.10.2, we may have to wait up to 500ms if KR is
                 * attempted.  82599 uses the same timing for 10g SFI.
                 */
                for (i = 0; i < 5; i++) {
                        /* Wait for the link partner to also set speed */
                        msleep(100);

                        /* If we have link, just jump out */
                        status = hw->mac.ops.check_link(hw, &link_speed,
                                                        &link_up, false);
                        if (status)
                                return status;

                        if (link_up)
                                goto out;
                }
        }

        if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
                speedcnt++;
                if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
                        highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;

                /* Set the module link speed */
                switch (hw->phy.media_type) {
                case ixgbe_media_type_fiber:
                        hw->mac.ops.set_rate_select_speed(hw,
                                                     IXGBE_LINK_SPEED_1GB_FULL);
                        break;
                case ixgbe_media_type_fiber_qsfp:
                        /* QSFP module automatically detects link speed */
                        break;
                default:
                        hw_dbg(hw, "Unexpected media type\n");
                        break;
                }

                /* Allow module to change analog characteristics (10G->1G) */
                msleep(40);

                status = hw->mac.ops.setup_mac_link(hw,
                                                    IXGBE_LINK_SPEED_1GB_FULL,
                                                    autoneg_wait_to_complete);
                if (status)
                        return status;

                /* Flap the Tx laser if it has not already been done */
                if (hw->mac.ops.flap_tx_laser)
                        hw->mac.ops.flap_tx_laser(hw);

                /* Wait for the link partner to also set speed */
                msleep(100);

                /* If we have link, just jump out */
                status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
                                                false);
                if (status)
                        return status;

                if (link_up)
                        goto out;
        }

        /* We didn't get link.  Configure back to the highest speed we tried,
         * (if there was more than one).  We call ourselves back with just the
         * single highest speed that the user requested.
         */
        if (speedcnt > 1)
                status = ixgbe_setup_mac_link_multispeed_fiber(hw,
                                                      highest_link_speed,
                                                      autoneg_wait_to_complete);

out:
        /* Set autoneg_advertised value based on input link speed */
        hw->phy.autoneg_advertised = 0;

        if (speed & IXGBE_LINK_SPEED_10GB_FULL)
                hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;

        if (speed & IXGBE_LINK_SPEED_1GB_FULL)
                hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;

        return status;
}

/**
 *  ixgbe_set_soft_rate_select_speed - Set module link speed
 *  @hw: pointer to hardware structure
 *  @speed: link speed to set
 *
 *  Set module link speed via the soft rate select.
 */
void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
                                      ixgbe_link_speed speed)
{
        u8 rs, eeprom_data;
        int status;

        switch (speed) {
        case IXGBE_LINK_SPEED_10GB_FULL:
                /* one bit mask same as setting on */
                rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
                break;
        case IXGBE_LINK_SPEED_1GB_FULL:
                rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
                break;
        default:
                hw_dbg(hw, "Invalid fixed module speed\n");
                return;
        }

        /* Set RS0 */
        status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
                                           IXGBE_I2C_EEPROM_DEV_ADDR2,
                                           &eeprom_data);
        if (status) {
                hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
                return;
        }

        eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;

        status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
                                            IXGBE_I2C_EEPROM_DEV_ADDR2,
                                            eeprom_data);
        if (status) {
                hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
                return;
        }

        /* Set RS1 */
        status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
                                           IXGBE_I2C_EEPROM_DEV_ADDR2,
                                           &eeprom_data);
        if (status) {
                hw_dbg(hw, "Failed to read Rx Rate Select RS1\n");
                return;
        }

        eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;

        status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
                                            IXGBE_I2C_EEPROM_DEV_ADDR2,
                                            eeprom_data);
        if (status) {
                hw_dbg(hw, "Failed to write Rx Rate Select RS1\n");
                return;
        }
}