drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright (c) 2023, Linaro Limited
   4  */
   5
   6 #include <linux/module.h>
   7 #include <linux/platform_device.h>
   8 #include <linux/regulator/consumer.h>
   9 #include <linux/regmap.h>
  10 #include <linux/of.h>
  11 #include <linux/phy/phy.h>
  12
  13 /* eUSB2 status registers */
  14 #define EUSB2_RPTR_STATUS               0x08
  15 #define RPTR_OK                         BIT(7)
  16
  17 /* eUSB2 control registers */
  18 #define EUSB2_EN_CTL1                   0x46
  19 #define EUSB2_RPTR_EN                   BIT(7)
  20
  21 #define EUSB2_FORCE_EN_5                0xe8
  22 #define F_CLK_19P2M_EN                  BIT(6)
  23
  24 #define EUSB2_FORCE_VAL_5               0xeD
  25 #define V_CLK_19P2M_EN                  BIT(6)
  26
  27 #define EUSB2_TUNE_USB2_CROSSOVER       0x50
  28 #define EUSB2_TUNE_IUSB2                0x51
  29 #define EUSB2_TUNE_RES_FSDIF            0x52
  30 #define EUSB2_TUNE_HSDISC               0x53
  31 #define EUSB2_TUNE_SQUELCH_U            0x54
  32 #define EUSB2_TUNE_USB2_SLEW            0x55
  33 #define EUSB2_TUNE_USB2_EQU             0x56
  34 #define EUSB2_TUNE_USB2_PREEM           0x57
  35 #define EUSB2_TUNE_USB2_HS_COMP_CUR     0x58
  36 #define EUSB2_TUNE_EUSB_SLEW            0x59
  37 #define EUSB2_TUNE_EUSB_EQU             0x5A
  38 #define EUSB2_TUNE_EUSB_HS_COMP_CUR     0x5B
  39
  40 enum eusb2_reg_layout {
  41         TUNE_EUSB_HS_COMP_CUR,
  42         TUNE_EUSB_EQU,
  43         TUNE_EUSB_SLEW,
  44         TUNE_USB2_HS_COMP_CUR,
  45         TUNE_USB2_PREEM,
  46         TUNE_USB2_EQU,
  47         TUNE_USB2_SLEW,
  48         TUNE_SQUELCH_U,
  49         TUNE_HSDISC,
  50         TUNE_RES_FSDIF,
  51         TUNE_IUSB2,
  52         TUNE_USB2_CROSSOVER,
  53         NUM_TUNE_FIELDS,
  54
  55         FORCE_VAL_5 = NUM_TUNE_FIELDS,
  56         FORCE_EN_5,
  57
  58         EN_CTL1,
  59
  60         RPTR_STATUS,
  61         LAYOUT_SIZE,
  62 };
  63
  64 struct eusb2_repeater_cfg {
  65         const u32 *init_tbl;
  66         int init_tbl_num;
  67         const char * const *vreg_list;
  68         int num_vregs;
  69 };
  70
  71 struct eusb2_repeater {
  72         struct device *dev;
  73         struct regmap *regmap;
  74         struct phy *phy;
  75         struct regulator_bulk_data *vregs;
  76         const struct eusb2_repeater_cfg *cfg;
  77         u32 base;
  78         enum phy_mode mode;
  79 };
  80
  81 static const char * const pm8550b_vreg_l[] = {
  82         "vdd18", "vdd3",
  83 };
  84
  85 static const u32 pm8550b_init_tbl[NUM_TUNE_FIELDS] = {
  86         [TUNE_IUSB2] = 0x8,
  87         [TUNE_SQUELCH_U] = 0x3,
  88         [TUNE_USB2_PREEM] = 0x5,
  89 };
  90
  91 static const u32 smb2360_init_tbl[NUM_TUNE_FIELDS] = {
  92         [TUNE_IUSB2] = 0x5,
  93         [TUNE_SQUELCH_U] = 0x3,
  94         [TUNE_USB2_PREEM] = 0x2,
  95 };
  96
  97 static const struct eusb2_repeater_cfg pm8550b_eusb2_cfg = {
  98         .init_tbl       = pm8550b_init_tbl,
  99         .init_tbl_num   = ARRAY_SIZE(pm8550b_init_tbl),
 100         .vreg_list      = pm8550b_vreg_l,
 101         .num_vregs      = ARRAY_SIZE(pm8550b_vreg_l),
 102 };
 103
 104 static const struct eusb2_repeater_cfg smb2360_eusb2_cfg = {
 105         .init_tbl       = smb2360_init_tbl,
 106         .init_tbl_num   = ARRAY_SIZE(smb2360_init_tbl),
 107         .vreg_list      = pm8550b_vreg_l,
 108         .num_vregs      = ARRAY_SIZE(pm8550b_vreg_l),
 109 };
 110
 111 static int eusb2_repeater_init_vregs(struct eusb2_repeater *rptr)
 112 {
 113         int num = rptr->cfg->num_vregs;
 114         struct device *dev = rptr->dev;
 115         int i;
 116
 117         rptr->vregs = devm_kcalloc(dev, num, sizeof(*rptr->vregs), GFP_KERNEL);
 118         if (!rptr->vregs)
 119                 return -ENOMEM;
 120
 121         for (i = 0; i < num; i++)
 122                 rptr->vregs[i].supply = rptr->cfg->vreg_list[i];
 123
 124         return devm_regulator_bulk_get(dev, num, rptr->vregs);
 125 }
 126
 127 static int eusb2_repeater_init(struct phy *phy)
 128 {
 129         struct eusb2_repeater *rptr = phy_get_drvdata(phy);
 130         struct device_node *np = rptr->dev->of_node;
 131         struct regmap *regmap = rptr->regmap;
 132         const u32 *init_tbl = rptr->cfg->init_tbl;
 133         u8 tune_usb2_preem = init_tbl[TUNE_USB2_PREEM];
 134         u8 tune_hsdisc = init_tbl[TUNE_HSDISC];
 135         u8 tune_iusb2 = init_tbl[TUNE_IUSB2];
 136         u32 base = rptr->base;
 137         u32 val;
 138         int ret;
 139
 140         of_property_read_u8(np, "qcom,tune-usb2-amplitude", &tune_iusb2);
 141         of_property_read_u8(np, "qcom,tune-usb2-disc-thres", &tune_hsdisc);
 142         of_property_read_u8(np, "qcom,tune-usb2-preem", &tune_usb2_preem);
 143
 144         ret = regulator_bulk_enable(rptr->cfg->num_vregs, rptr->vregs);
 145         if (ret)
 146                 return ret;
 147
 148         regmap_write(regmap, base + EUSB2_EN_CTL1, EUSB2_RPTR_EN);
 149
 150         regmap_write(regmap, base + EUSB2_TUNE_EUSB_HS_COMP_CUR, init_tbl[TUNE_EUSB_HS_COMP_CUR]);
 151         regmap_write(regmap, base + EUSB2_TUNE_EUSB_EQU, init_tbl[TUNE_EUSB_EQU]);
 152         regmap_write(regmap, base + EUSB2_TUNE_EUSB_SLEW, init_tbl[TUNE_EUSB_SLEW]);
 153         regmap_write(regmap, base + EUSB2_TUNE_USB2_HS_COMP_CUR, init_tbl[TUNE_USB2_HS_COMP_CUR]);
 154         regmap_write(regmap, base + EUSB2_TUNE_USB2_EQU, init_tbl[TUNE_USB2_EQU]);
 155         regmap_write(regmap, base + EUSB2_TUNE_USB2_SLEW, init_tbl[TUNE_USB2_SLEW]);
 156         regmap_write(regmap, base + EUSB2_TUNE_SQUELCH_U, init_tbl[TUNE_SQUELCH_U]);
 157         regmap_write(regmap, base + EUSB2_TUNE_RES_FSDIF, init_tbl[TUNE_RES_FSDIF]);
 158         regmap_write(regmap, base + EUSB2_TUNE_USB2_CROSSOVER, init_tbl[TUNE_USB2_CROSSOVER]);
 159
 160         regmap_write(regmap, base + EUSB2_TUNE_USB2_PREEM, tune_usb2_preem);
 161         regmap_write(regmap, base + EUSB2_TUNE_HSDISC, tune_hsdisc);
 162         regmap_write(regmap, base + EUSB2_TUNE_IUSB2, tune_iusb2);
 163
 164         ret = regmap_read_poll_timeout(regmap, base + EUSB2_RPTR_STATUS, val, val & RPTR_OK, 10, 5);
 165         if (ret)
 166                 dev_err(rptr->dev, "initialization timed-out\n");
 167
 168         return ret;
 169 }
 170
 171 static int eusb2_repeater_set_mode(struct phy *phy,
 172                                    enum phy_mode mode, int submode)
 173 {
 174         struct eusb2_repeater *rptr = phy_get_drvdata(phy);
 175         struct regmap *regmap = rptr->regmap;
 176         u32 base = rptr->base;
 177
 178         switch (mode) {
 179         case PHY_MODE_USB_HOST:
 180                 /*
 181                  * CM.Lx is prohibited when repeater is already into Lx state as
 182                  * per eUSB 1.2 Spec. Below implement software workaround until
 183                  * PHY and controller is fixing seen observation.
 184                  */
 185                 regmap_write(regmap, base + EUSB2_FORCE_EN_5, F_CLK_19P2M_EN);
 186                 regmap_write(regmap, base + EUSB2_FORCE_VAL_5, V_CLK_19P2M_EN);
 187                 break;
 188         case PHY_MODE_USB_DEVICE:
 189                 /*
 190                  * In device mode clear host mode related workaround as there
 191                  * is no repeater reset available, and enable/disable of
 192                  * repeater doesn't clear previous value due to shared
 193                  * regulators (say host <-> device mode switch).
 194                  */
 195                 regmap_write(regmap, base + EUSB2_FORCE_EN_5, 0);
 196                 regmap_write(regmap, base + EUSB2_FORCE_VAL_5, 0);
 197                 break;
 198         default:
 199                 return -EINVAL;
 200         }
 201
 202         return 0;
 203 }
 204
 205 static int eusb2_repeater_exit(struct phy *phy)
 206 {
 207         struct eusb2_repeater *rptr = phy_get_drvdata(phy);
 208
 209         return regulator_bulk_disable(rptr->cfg->num_vregs, rptr->vregs);
 210 }
 211
 212 static const struct phy_ops eusb2_repeater_ops = {
 213         .init           = eusb2_repeater_init,
 214         .exit           = eusb2_repeater_exit,
 215         .set_mode       = eusb2_repeater_set_mode,
 216         .owner          = THIS_MODULE,
 217 };
 218
 219 static int eusb2_repeater_probe(struct platform_device *pdev)
 220 {
 221         struct eusb2_repeater *rptr;
 222         struct device *dev = &pdev->dev;
 223         struct phy_provider *phy_provider;
 224         struct device_node *np = dev->of_node;
 225         u32 res;
 226         int ret;
 227
 228         rptr = devm_kzalloc(dev, sizeof(*rptr), GFP_KERNEL);
 229         if (!rptr)
 230                 return -ENOMEM;
 231
 232         rptr->dev = dev;
 233         dev_set_drvdata(dev, rptr);
 234
 235         rptr->cfg = of_device_get_match_data(dev);
 236         if (!rptr->cfg)
 237                 return -EINVAL;
 238
 239         rptr->regmap = dev_get_regmap(dev->parent, NULL);
 240         if (!rptr->regmap)
 241                 return -ENODEV;
 242
 243         ret = of_property_read_u32(np, "reg", &res);
 244         if (ret < 0)
 245                 return ret;
 246
 247         rptr->base = res;
 248
 249         ret = eusb2_repeater_init_vregs(rptr);
 250         if (ret < 0) {
 251                 dev_err(dev, "unable to get supplies\n");
 252                 return ret;
 253         }
 254
 255         rptr->phy = devm_phy_create(dev, np, &eusb2_repeater_ops);
 256         if (IS_ERR(rptr->phy)) {
 257                 dev_err(dev, "failed to create PHY: %d\n", ret);
 258                 return PTR_ERR(rptr->phy);
 259         }
 260
 261         phy_set_drvdata(rptr->phy, rptr);
 262
 263         phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 264         if (IS_ERR(phy_provider))
 265                 return PTR_ERR(phy_provider);
 266
 267         dev_info(dev, "Registered Qcom-eUSB2 repeater\n");
 268
 269         return 0;
 270 }
 271
 272 static void eusb2_repeater_remove(struct platform_device *pdev)
 273 {
 274         struct eusb2_repeater *rptr = platform_get_drvdata(pdev);
 275
 276         if (!rptr)
 277                 return;
 278
 279         eusb2_repeater_exit(rptr->phy);
 280 }
 281
 282 static const struct of_device_id eusb2_repeater_of_match_table[] = {
 283         {
 284                 .compatible = "qcom,pm8550b-eusb2-repeater",
 285                 .data = &pm8550b_eusb2_cfg,
 286         },
 287         {
 288                 .compatible = "qcom,smb2360-eusb2-repeater",
 289                 .data = &smb2360_eusb2_cfg,
 290         },
 291         { },
 292 };
 293 MODULE_DEVICE_TABLE(of, eusb2_repeater_of_match_table);
 294
 295 static struct platform_driver eusb2_repeater_driver = {
 296         .probe          = eusb2_repeater_probe,
 297         .remove         = eusb2_repeater_remove,
 298         .driver = {
 299                 .name   = "qcom-eusb2-repeater",
 300                 .of_match_table = eusb2_repeater_of_match_table,
 301         },
 302 };
 303
 304 module_platform_driver(eusb2_repeater_driver);
 305
 306 MODULE_DESCRIPTION("Qualcomm PMIC eUSB2 Repeater driver");
 307 MODULE_LICENSE("GPL");