?  search:
summary | log | graphiclog1 | graphiclog2 | commit | commitdiff | tree | refs | edit | fork
blame | history | raw | HEAD
printf: Remove unused 'bprintf'
[drm/drm-misc.git] / drivers / mmc / host / sunxi-mmc.c
blob1508eead5d0178ca8d486eddf5b85bfad6c828ee
1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Driver for sunxi SD/MMC host controllers
4 * (C) Copyright 2007-2011 Reuuimlla Technology Co., Ltd.
5 * (C) Copyright 2007-2011 Aaron Maoye <leafy.myeh@reuuimllatech.com>
6 * (C) Copyright 2013-2014 O2S GmbH <www.o2s.ch>
7 * (C) Copyright 2013-2014 David Lanzendörfer <david.lanzendoerfer@o2s.ch>
8 * (C) Copyright 2013-2014 Hans de Goede <hdegoede@redhat.com>
9 * (C) Copyright 2017 Sootech SA
10 */
11
12 #include <linux/clk.h>
13 #include <linux/clk/sunxi-ng.h>
14 #include <linux/delay.h>
15 #include <linux/device.h>
16 #include <linux/dma-mapping.h>
17 #include <linux/err.h>
18 #include <linux/interrupt.h>
19 #include <linux/io.h>
20 #include <linux/kernel.h>
21 #include <linux/mmc/card.h>
22 #include <linux/mmc/core.h>
23 #include <linux/mmc/host.h>
24 #include <linux/mmc/mmc.h>
25 #include <linux/mmc/sd.h>
26 #include <linux/mmc/sdio.h>
27 #include <linux/mmc/slot-gpio.h>
28 #include <linux/module.h>
29 #include <linux/mod_devicetable.h>
30 #include <linux/of_address.h>
31 #include <linux/of_platform.h>
32 #include <linux/platform_device.h>
33 #include <linux/pm_runtime.h>
34 #include <linux/regulator/consumer.h>
35 #include <linux/reset.h>
36 #include <linux/scatterlist.h>
37 #include <linux/slab.h>
38 #include <linux/spinlock.h>
39
40 /* register offset definitions */
41 #define SDXC_REG_GCTRL (0x00) /* SMC Global Control Register */
42 #define SDXC_REG_CLKCR (0x04) /* SMC Clock Control Register */
43 #define SDXC_REG_TMOUT (0x08) /* SMC Time Out Register */
44 #define SDXC_REG_WIDTH (0x0C) /* SMC Bus Width Register */
45 #define SDXC_REG_BLKSZ (0x10) /* SMC Block Size Register */
46 #define SDXC_REG_BCNTR (0x14) /* SMC Byte Count Register */
47 #define SDXC_REG_CMDR (0x18) /* SMC Command Register */
48 #define SDXC_REG_CARG (0x1C) /* SMC Argument Register */
49 #define SDXC_REG_RESP0 (0x20) /* SMC Response Register 0 */
50 #define SDXC_REG_RESP1 (0x24) /* SMC Response Register 1 */
51 #define SDXC_REG_RESP2 (0x28) /* SMC Response Register 2 */
52 #define SDXC_REG_RESP3 (0x2C) /* SMC Response Register 3 */
53 #define SDXC_REG_IMASK (0x30) /* SMC Interrupt Mask Register */
54 #define SDXC_REG_MISTA (0x34) /* SMC Masked Interrupt Status Register */
55 #define SDXC_REG_RINTR (0x38) /* SMC Raw Interrupt Status Register */
56 #define SDXC_REG_STAS (0x3C) /* SMC Status Register */
57 #define SDXC_REG_FTRGL (0x40) /* SMC FIFO Threshold Watermark Registe */
58 #define SDXC_REG_FUNS (0x44) /* SMC Function Select Register */
59 #define SDXC_REG_CBCR (0x48) /* SMC CIU Byte Count Register */
60 #define SDXC_REG_BBCR (0x4C) /* SMC BIU Byte Count Register */
61 #define SDXC_REG_DBGC (0x50) /* SMC Debug Enable Register */
62 #define SDXC_REG_HWRST (0x78) /* SMC Card Hardware Reset for Register */
63 #define SDXC_REG_DMAC (0x80) /* SMC IDMAC Control Register */
64 #define SDXC_REG_DLBA (0x84) /* SMC IDMAC Descriptor List Base Addre */
65 #define SDXC_REG_IDST (0x88) /* SMC IDMAC Status Register */
66 #define SDXC_REG_IDIE (0x8C) /* SMC IDMAC Interrupt Enable Register */
67 #define SDXC_REG_CHDA (0x90)
68 #define SDXC_REG_CBDA (0x94)
69
70 /* New registers introduced in A64 */
71 #define SDXC_REG_A12A 0x058 /* SMC Auto Command 12 Register */
72 #define SDXC_REG_SD_NTSR 0x05C /* SMC New Timing Set Register */
73 #define SDXC_REG_DRV_DL 0x140 /* Drive Delay Control Register */
74 #define SDXC_REG_SAMP_DL_REG 0x144 /* SMC sample delay control */
75 #define SDXC_REG_DS_DL_REG 0x148 /* SMC data strobe delay control */
76
77 #define mmc_readl(host, reg) \
78 readl((host)->reg_base + SDXC_##reg)
79 #define mmc_writel(host, reg, value) \
80 writel((value), (host)->reg_base + SDXC_##reg)
81
82 /* global control register bits */
83 #define SDXC_SOFT_RESET BIT(0)
84 #define SDXC_FIFO_RESET BIT(1)
85 #define SDXC_DMA_RESET BIT(2)
86 #define SDXC_INTERRUPT_ENABLE_BIT BIT(4)
87 #define SDXC_DMA_ENABLE_BIT BIT(5)
88 #define SDXC_DEBOUNCE_ENABLE_BIT BIT(8)
89 #define SDXC_POSEDGE_LATCH_DATA BIT(9)
90 #define SDXC_DDR_MODE BIT(10)
91 #define SDXC_MEMORY_ACCESS_DONE BIT(29)
92 #define SDXC_ACCESS_DONE_DIRECT BIT(30)
93 #define SDXC_ACCESS_BY_AHB BIT(31)
94 #define SDXC_ACCESS_BY_DMA (0 << 31)
95 #define SDXC_HARDWARE_RESET \
96 (SDXC_SOFT_RESET | SDXC_FIFO_RESET | SDXC_DMA_RESET)
97
98 /* clock control bits */
99 #define SDXC_MASK_DATA0 BIT(31)
100 #define SDXC_CARD_CLOCK_ON BIT(16)
101 #define SDXC_LOW_POWER_ON BIT(17)
102
103 /* bus width */
104 #define SDXC_WIDTH1 0
105 #define SDXC_WIDTH4 1
106 #define SDXC_WIDTH8 2
107
108 /* smc command bits */
109 #define SDXC_RESP_EXPIRE BIT(6)
110 #define SDXC_LONG_RESPONSE BIT(7)
111 #define SDXC_CHECK_RESPONSE_CRC BIT(8)
112 #define SDXC_DATA_EXPIRE BIT(9)
113 #define SDXC_WRITE BIT(10)
114 #define SDXC_SEQUENCE_MODE BIT(11)
115 #define SDXC_SEND_AUTO_STOP BIT(12)
116 #define SDXC_WAIT_PRE_OVER BIT(13)
117 #define SDXC_STOP_ABORT_CMD BIT(14)
118 #define SDXC_SEND_INIT_SEQUENCE BIT(15)
119 #define SDXC_UPCLK_ONLY BIT(21)
120 #define SDXC_READ_CEATA_DEV BIT(22)
121 #define SDXC_CCS_EXPIRE BIT(23)
122 #define SDXC_ENABLE_BIT_BOOT BIT(24)
123 #define SDXC_ALT_BOOT_OPTIONS BIT(25)
124 #define SDXC_BOOT_ACK_EXPIRE BIT(26)
125 #define SDXC_BOOT_ABORT BIT(27)
126 #define SDXC_VOLTAGE_SWITCH BIT(28)
127 #define SDXC_USE_HOLD_REGISTER BIT(29)
128 #define SDXC_START BIT(31)
129
130 /* interrupt bits */
131 #define SDXC_RESP_ERROR BIT(1)
132 #define SDXC_COMMAND_DONE BIT(2)
133 #define SDXC_DATA_OVER BIT(3)
134 #define SDXC_TX_DATA_REQUEST BIT(4)
135 #define SDXC_RX_DATA_REQUEST BIT(5)
136 #define SDXC_RESP_CRC_ERROR BIT(6)
137 #define SDXC_DATA_CRC_ERROR BIT(7)
138 #define SDXC_RESP_TIMEOUT BIT(8)
139 #define SDXC_DATA_TIMEOUT BIT(9)
140 #define SDXC_VOLTAGE_CHANGE_DONE BIT(10)
141 #define SDXC_FIFO_RUN_ERROR BIT(11)
142 #define SDXC_HARD_WARE_LOCKED BIT(12)
143 #define SDXC_START_BIT_ERROR BIT(13)
144 #define SDXC_AUTO_COMMAND_DONE BIT(14)
145 #define SDXC_END_BIT_ERROR BIT(15)
146 #define SDXC_SDIO_INTERRUPT BIT(16)
147 #define SDXC_CARD_INSERT BIT(30)
148 #define SDXC_CARD_REMOVE BIT(31)
149 #define SDXC_INTERRUPT_ERROR_BIT \
150 (SDXC_RESP_ERROR | SDXC_RESP_CRC_ERROR | SDXC_DATA_CRC_ERROR | \
151 SDXC_RESP_TIMEOUT | SDXC_DATA_TIMEOUT | SDXC_FIFO_RUN_ERROR | \
152 SDXC_HARD_WARE_LOCKED | SDXC_START_BIT_ERROR | SDXC_END_BIT_ERROR)
153 #define SDXC_INTERRUPT_DONE_BIT \
154 (SDXC_AUTO_COMMAND_DONE | SDXC_DATA_OVER | \
155 SDXC_COMMAND_DONE | SDXC_VOLTAGE_CHANGE_DONE)
156
157 /* status */
158 #define SDXC_RXWL_FLAG BIT(0)
159 #define SDXC_TXWL_FLAG BIT(1)
160 #define SDXC_FIFO_EMPTY BIT(2)
161 #define SDXC_FIFO_FULL BIT(3)
162 #define SDXC_CARD_PRESENT BIT(8)
163 #define SDXC_CARD_DATA_BUSY BIT(9)
164 #define SDXC_DATA_FSM_BUSY BIT(10)
165 #define SDXC_DMA_REQUEST BIT(31)
166 #define SDXC_FIFO_SIZE 16
167
168 /* Function select */
169 #define SDXC_CEATA_ON (0xceaa << 16)
170 #define SDXC_SEND_IRQ_RESPONSE BIT(0)
171 #define SDXC_SDIO_READ_WAIT BIT(1)
172 #define SDXC_ABORT_READ_DATA BIT(2)
173 #define SDXC_SEND_CCSD BIT(8)
174 #define SDXC_SEND_AUTO_STOPCCSD BIT(9)
175 #define SDXC_CEATA_DEV_IRQ_ENABLE BIT(10)
176
177 /* IDMA controller bus mod bit field */
178 #define SDXC_IDMAC_SOFT_RESET BIT(0)
179 #define SDXC_IDMAC_FIX_BURST BIT(1)
180 #define SDXC_IDMAC_IDMA_ON BIT(7)
181 #define SDXC_IDMAC_REFETCH_DES BIT(31)
182
183 /* IDMA status bit field */
184 #define SDXC_IDMAC_TRANSMIT_INTERRUPT BIT(0)
185 #define SDXC_IDMAC_RECEIVE_INTERRUPT BIT(1)
186 #define SDXC_IDMAC_FATAL_BUS_ERROR BIT(2)
187 #define SDXC_IDMAC_DESTINATION_INVALID BIT(4)
188 #define SDXC_IDMAC_CARD_ERROR_SUM BIT(5)
189 #define SDXC_IDMAC_NORMAL_INTERRUPT_SUM BIT(8)
190 #define SDXC_IDMAC_ABNORMAL_INTERRUPT_SUM BIT(9)
191 #define SDXC_IDMAC_HOST_ABORT_INTERRUPT BIT(10)
192 #define SDXC_IDMAC_IDLE (0 << 13)
193 #define SDXC_IDMAC_SUSPEND (1 << 13)
194 #define SDXC_IDMAC_DESC_READ (2 << 13)
195 #define SDXC_IDMAC_DESC_CHECK (3 << 13)
196 #define SDXC_IDMAC_READ_REQUEST_WAIT (4 << 13)
197 #define SDXC_IDMAC_WRITE_REQUEST_WAIT (5 << 13)
198 #define SDXC_IDMAC_READ (6 << 13)
199 #define SDXC_IDMAC_WRITE (7 << 13)
200 #define SDXC_IDMAC_DESC_CLOSE (8 << 13)
201
202 /*
203 * If the idma-des-size-bits of property is ie 13, bufsize bits are:
204 * Bits 0-12: buf1 size
205 * Bits 13-25: buf2 size
206 * Bits 26-31: not used
207 * Since we only ever set buf1 size, we can simply store it directly.
208 */
209 #define SDXC_IDMAC_DES0_DIC BIT(1) /* disable interrupt on completion */
210 #define SDXC_IDMAC_DES0_LD BIT(2) /* last descriptor */
211 #define SDXC_IDMAC_DES0_FD BIT(3) /* first descriptor */
212 #define SDXC_IDMAC_DES0_CH BIT(4) /* chain mode */
213 #define SDXC_IDMAC_DES0_ER BIT(5) /* end of ring */
214 #define SDXC_IDMAC_DES0_CES BIT(30) /* card error summary */
215 #define SDXC_IDMAC_DES0_OWN BIT(31) /* 1-idma owns it, 0-host owns it */
216
217 #define SDXC_CLK_400K 0
218 #define SDXC_CLK_25M 1
219 #define SDXC_CLK_50M 2
220 #define SDXC_CLK_50M_DDR 3
221 #define SDXC_CLK_50M_DDR_8BIT 4
222
223 #define SDXC_2X_TIMING_MODE BIT(31)
224
225 #define SDXC_CAL_START BIT(15)
226 #define SDXC_CAL_DONE BIT(14)
227 #define SDXC_CAL_DL_SHIFT 8
228 #define SDXC_CAL_DL_SW_EN BIT(7)
229 #define SDXC_CAL_DL_SW_SHIFT 0
230 #define SDXC_CAL_DL_MASK 0x3f
231
232 #define SDXC_CAL_TIMEOUT 3 /* in seconds, 3s is enough*/
233
234 struct sunxi_mmc_clk_delay {
235 u32 output;
236 u32 sample;
237 };
238
239 struct sunxi_idma_des {
240 __le32 config;
241 __le32 buf_size;
242 __le32 buf_addr_ptr1;
243 __le32 buf_addr_ptr2;
244 };
245
246 struct sunxi_mmc_cfg {
247 u32 idma_des_size_bits;
248 u32 idma_des_shift;
249 const struct sunxi_mmc_clk_delay *clk_delays;
250
251 /* does the IP block support autocalibration? */
252 bool can_calibrate;
253
254 /* Does DATA0 needs to be masked while the clock is updated */
255 bool mask_data0;
256
257 /*
258 * hardware only supports new timing mode, either due to lack of
259 * a mode switch in the clock controller, or the mmc controller
260 * is permanently configured in the new timing mode, without the
261 * NTSR mode switch.
262 */
263 bool needs_new_timings;
264
265 /* clock hardware can switch between old and new timing modes */
266 bool ccu_has_timings_switch;
267 };
268
269 struct sunxi_mmc_host {
270 struct device *dev;
271 struct mmc_host *mmc;
272 struct reset_control *reset;
273 const struct sunxi_mmc_cfg *cfg;
274
275 /* IO mapping base */
276 void __iomem *reg_base;
277
278 /* clock management */
279 struct clk *clk_ahb;
280 struct clk *clk_mmc;
281 struct clk *clk_sample;
282 struct clk *clk_output;
283
284 /* irq */
285 spinlock_t lock;
286 int irq;
287 u32 int_sum;
288 u32 sdio_imask;
289
290 /* dma */
291 dma_addr_t sg_dma;
292 void *sg_cpu;
293 bool wait_dma;
294
295 struct mmc_request *mrq;
296 struct mmc_request *manual_stop_mrq;
297 int ferror;
298
299 /* vqmmc */
300 bool vqmmc_enabled;
301
302 /* timings */
303 bool use_new_timings;
304 };
305
306 static int sunxi_mmc_reset_host(struct sunxi_mmc_host *host)
307 {
308 unsigned long expire = jiffies + msecs_to_jiffies(250);
309 u32 rval;
310
311 mmc_writel(host, REG_GCTRL, SDXC_HARDWARE_RESET);
312 do {
313 rval = mmc_readl(host, REG_GCTRL);
314 } while (time_before(jiffies, expire) && (rval & SDXC_HARDWARE_RESET));
315
316 if (rval & SDXC_HARDWARE_RESET) {
317 dev_err(mmc_dev(host->mmc), "fatal err reset timeout\n");
318 return -EIO;
319 }
320
321 return 0;
322 }
323
324 static int sunxi_mmc_init_host(struct sunxi_mmc_host *host)
325 {
326 u32 rval;
327
328 if (sunxi_mmc_reset_host(host))
329 return -EIO;
330
331 /*
332 * Burst 8 transfers, RX trigger level: 7, TX trigger level: 8
333 *
334 * TODO: sun9i has a larger FIFO and supports higher trigger values
335 */
336 mmc_writel(host, REG_FTRGL, 0x20070008);
337 /* Maximum timeout value */
338 mmc_writel(host, REG_TMOUT, 0xffffffff);
339 /* Unmask SDIO interrupt if needed */
340 mmc_writel(host, REG_IMASK, host->sdio_imask);
341 /* Clear all pending interrupts */
342 mmc_writel(host, REG_RINTR, 0xffffffff);
343 /* Debug register? undocumented */
344 mmc_writel(host, REG_DBGC, 0xdeb);
345 /* Enable CEATA support */
346 mmc_writel(host, REG_FUNS, SDXC_CEATA_ON);
347 /* Set DMA descriptor list base address */
348 mmc_writel(host, REG_DLBA, host->sg_dma >> host->cfg->idma_des_shift);
349
350 rval = mmc_readl(host, REG_GCTRL);
351 rval |= SDXC_INTERRUPT_ENABLE_BIT;
352 /* Undocumented, but found in Allwinner code */
353 rval &= ~SDXC_ACCESS_DONE_DIRECT;
354 mmc_writel(host, REG_GCTRL, rval);
355
356 return 0;
357 }
358
359 static void sunxi_mmc_init_idma_des(struct sunxi_mmc_host *host,
360 struct mmc_data *data)
361 {
362 struct sunxi_idma_des *pdes = (struct sunxi_idma_des *)host->sg_cpu;
363 dma_addr_t next_desc = host->sg_dma;
364 int i, max_len = (1 << host->cfg->idma_des_size_bits);
365
366 for (i = 0; i < data->sg_len; i++) {
367 pdes[i].config = cpu_to_le32(SDXC_IDMAC_DES0_CH |
368 SDXC_IDMAC_DES0_OWN |
369 SDXC_IDMAC_DES0_DIC);
370
371 if (data->sg[i].length == max_len)
372 pdes[i].buf_size = 0; /* 0 == max_len */
373 else
374 pdes[i].buf_size = cpu_to_le32(data->sg[i].length);
375
376 next_desc += sizeof(struct sunxi_idma_des);
377 pdes[i].buf_addr_ptr1 =
378 cpu_to_le32(sg_dma_address(&data->sg[i]) >>
379 host->cfg->idma_des_shift);
380 pdes[i].buf_addr_ptr2 =
381 cpu_to_le32(next_desc >>
382 host->cfg->idma_des_shift);
383 }
384
385 pdes[0].config |= cpu_to_le32(SDXC_IDMAC_DES0_FD);
386 pdes[i - 1].config |= cpu_to_le32(SDXC_IDMAC_DES0_LD |
387 SDXC_IDMAC_DES0_ER);
388 pdes[i - 1].config &= cpu_to_le32(~SDXC_IDMAC_DES0_DIC);
389 pdes[i - 1].buf_addr_ptr2 = 0;
390
391 /*
392 * Avoid the io-store starting the idmac hitting io-mem before the
393 * descriptors hit the main-mem.
394 */
395 wmb();
396 }
397
398 static int sunxi_mmc_map_dma(struct sunxi_mmc_host *host,
399 struct mmc_data *data)
400 {
401 u32 i, dma_len;
402 struct scatterlist *sg;
403
404 dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
405 mmc_get_dma_dir(data));
406 if (dma_len == 0) {
407 dev_err(mmc_dev(host->mmc), "dma_map_sg failed\n");
408 return -ENOMEM;
409 }
410
411 for_each_sg(data->sg, sg, data->sg_len, i) {
412 if (sg->offset & 3 || sg->length & 3) {
413 dev_err(mmc_dev(host->mmc),
414 "unaligned scatterlist: os %x length %d\n",
415 sg->offset, sg->length);
416 return -EINVAL;
417 }
418 }
419
420 return 0;
421 }
422
423 static void sunxi_mmc_start_dma(struct sunxi_mmc_host *host,
424 struct mmc_data *data)
425 {
426 u32 rval;
427
428 sunxi_mmc_init_idma_des(host, data);
429
430 rval = mmc_readl(host, REG_GCTRL);
431 rval |= SDXC_DMA_ENABLE_BIT;
432 mmc_writel(host, REG_GCTRL, rval);
433 rval |= SDXC_DMA_RESET;
434 mmc_writel(host, REG_GCTRL, rval);
435
436 mmc_writel(host, REG_DMAC, SDXC_IDMAC_SOFT_RESET);
437
438 if (!(data->flags & MMC_DATA_WRITE))
439 mmc_writel(host, REG_IDIE, SDXC_IDMAC_RECEIVE_INTERRUPT);
440
441 mmc_writel(host, REG_DMAC,
442 SDXC_IDMAC_FIX_BURST | SDXC_IDMAC_IDMA_ON);
443 }
444
445 static void sunxi_mmc_send_manual_stop(struct sunxi_mmc_host *host,
446 struct mmc_request *req)
447 {
448 u32 arg, cmd_val, ri;
449 unsigned long expire = jiffies + msecs_to_jiffies(1000);
450
451 cmd_val = SDXC_START | SDXC_RESP_EXPIRE |
452 SDXC_STOP_ABORT_CMD | SDXC_CHECK_RESPONSE_CRC;
453
454 if (req->cmd->opcode == SD_IO_RW_EXTENDED) {
455 cmd_val |= SD_IO_RW_DIRECT;
456 arg = (1 << 31) | (0 << 28) | (SDIO_CCCR_ABORT << 9) |
457 ((req->cmd->arg >> 28) & 0x7);
458 } else {
459 cmd_val |= MMC_STOP_TRANSMISSION;
460 arg = 0;
461 }
462
463 mmc_writel(host, REG_CARG, arg);
464 mmc_writel(host, REG_CMDR, cmd_val);
465
466 do {
467 ri = mmc_readl(host, REG_RINTR);
468 } while (!(ri & (SDXC_COMMAND_DONE | SDXC_INTERRUPT_ERROR_BIT)) &&
469 time_before(jiffies, expire));
470
471 if (!(ri & SDXC_COMMAND_DONE) || (ri & SDXC_INTERRUPT_ERROR_BIT)) {
472 dev_err(mmc_dev(host->mmc), "send stop command failed\n");
473 if (req->stop)
474 req->stop->resp[0] = -ETIMEDOUT;
475 } else {
476 if (req->stop)
477 req->stop->resp[0] = mmc_readl(host, REG_RESP0);
478 }
479
480 mmc_writel(host, REG_RINTR, 0xffff);
481 }
482
483 static void sunxi_mmc_dump_errinfo(struct sunxi_mmc_host *host)
484 {
485 struct mmc_command *cmd = host->mrq->cmd;
486 struct mmc_data *data = host->mrq->data;
487
488 /* For some cmds timeout is normal with sd/mmc cards */
489 if ((host->int_sum & SDXC_INTERRUPT_ERROR_BIT) ==
490 SDXC_RESP_TIMEOUT && (cmd->opcode == SD_IO_SEND_OP_COND ||
491 cmd->opcode == SD_IO_RW_DIRECT))
492 return;
493
494 dev_dbg(mmc_dev(host->mmc),
495 "smc %d err, cmd %d,%s%s%s%s%s%s%s%s%s%s !!\n",
496 host->mmc->index, cmd->opcode,
497 data ? (data->flags & MMC_DATA_WRITE ? " WR" : " RD") : "",
498 host->int_sum & SDXC_RESP_ERROR ? " RE" : "",
499 host->int_sum & SDXC_RESP_CRC_ERROR ? " RCE" : "",
500 host->int_sum & SDXC_DATA_CRC_ERROR ? " DCE" : "",
501 host->int_sum & SDXC_RESP_TIMEOUT ? " RTO" : "",
502 host->int_sum & SDXC_DATA_TIMEOUT ? " DTO" : "",
503 host->int_sum & SDXC_FIFO_RUN_ERROR ? " FE" : "",
504 host->int_sum & SDXC_HARD_WARE_LOCKED ? " HL" : "",
505 host->int_sum & SDXC_START_BIT_ERROR ? " SBE" : "",
506 host->int_sum & SDXC_END_BIT_ERROR ? " EBE" : ""
507 );
508 }
509
510 /* Called in interrupt context! */
511 static irqreturn_t sunxi_mmc_finalize_request(struct sunxi_mmc_host *host)
512 {
513 struct mmc_request *mrq = host->mrq;
514 struct mmc_data *data = mrq->data;
515 u32 rval;
516
517 mmc_writel(host, REG_IMASK, host->sdio_imask);
518 mmc_writel(host, REG_IDIE, 0);
519
520 if (host->int_sum & SDXC_INTERRUPT_ERROR_BIT) {
521 sunxi_mmc_dump_errinfo(host);
522 mrq->cmd->error = -ETIMEDOUT;
523
524 if (data) {
525 data->error = -ETIMEDOUT;
526 host->manual_stop_mrq = mrq;
527 }
528
529 if (mrq->stop)
530 mrq->stop->error = -ETIMEDOUT;
531 } else {
532 if (mrq->cmd->flags & MMC_RSP_136) {
533 mrq->cmd->resp[0] = mmc_readl(host, REG_RESP3);
534 mrq->cmd->resp[1] = mmc_readl(host, REG_RESP2);
535 mrq->cmd->resp[2] = mmc_readl(host, REG_RESP1);
536 mrq->cmd->resp[3] = mmc_readl(host, REG_RESP0);
537 } else {
538 mrq->cmd->resp[0] = mmc_readl(host, REG_RESP0);
539 }
540
541 if (data)
542 data->bytes_xfered = data->blocks * data->blksz;
543 }
544
545 if (data) {
546 mmc_writel(host, REG_IDST, 0x337);
547 mmc_writel(host, REG_DMAC, 0);
548 rval = mmc_readl(host, REG_GCTRL);
549 rval |= SDXC_DMA_RESET;
550 mmc_writel(host, REG_GCTRL, rval);
551 rval &= ~SDXC_DMA_ENABLE_BIT;
552 mmc_writel(host, REG_GCTRL, rval);
553 rval |= SDXC_FIFO_RESET;
554 mmc_writel(host, REG_GCTRL, rval);
555 dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
556 mmc_get_dma_dir(data));
557 }
558
559 mmc_writel(host, REG_RINTR, 0xffff);
560
561 host->mrq = NULL;
562 host->int_sum = 0;
563 host->wait_dma = false;
564
565 return host->manual_stop_mrq ? IRQ_WAKE_THREAD : IRQ_HANDLED;
566 }
567
568 static irqreturn_t sunxi_mmc_irq(int irq, void *dev_id)
569 {
570 struct sunxi_mmc_host *host = dev_id;
571 struct mmc_request *mrq;
572 u32 msk_int, idma_int;
573 bool finalize = false;
574 bool sdio_int = false;
575 irqreturn_t ret = IRQ_HANDLED;
576
577 spin_lock(&host->lock);
578
579 idma_int = mmc_readl(host, REG_IDST);
580 msk_int = mmc_readl(host, REG_MISTA);
581
582 dev_dbg(mmc_dev(host->mmc), "irq: rq %p mi %08x idi %08x\n",
583 host->mrq, msk_int, idma_int);
584
585 mrq = host->mrq;
586 if (mrq) {
587 if (idma_int & SDXC_IDMAC_RECEIVE_INTERRUPT)
588 host->wait_dma = false;
589
590 host->int_sum |= msk_int;
591
592 /* Wait for COMMAND_DONE on RESPONSE_TIMEOUT before finalize */
593 if ((host->int_sum & SDXC_RESP_TIMEOUT) &&
594 !(host->int_sum & SDXC_COMMAND_DONE))
595 mmc_writel(host, REG_IMASK,
596 host->sdio_imask | SDXC_COMMAND_DONE);
597 /* Don't wait for dma on error */
598 else if (host->int_sum & SDXC_INTERRUPT_ERROR_BIT)
599 finalize = true;
600 else if ((host->int_sum & SDXC_INTERRUPT_DONE_BIT) &&
601 !host->wait_dma)
602 finalize = true;
603 }
604
605 if (msk_int & SDXC_SDIO_INTERRUPT)
606 sdio_int = true;
607
608 mmc_writel(host, REG_RINTR, msk_int);
609 mmc_writel(host, REG_IDST, idma_int);
610
611 if (finalize)
612 ret = sunxi_mmc_finalize_request(host);
613
614 spin_unlock(&host->lock);
615
616 if (finalize && ret == IRQ_HANDLED)
617 mmc_request_done(host->mmc, mrq);
618
619 if (sdio_int)
620 mmc_signal_sdio_irq(host->mmc);
621
622 return ret;
623 }
624
625 static irqreturn_t sunxi_mmc_handle_manual_stop(int irq, void *dev_id)
626 {
627 struct sunxi_mmc_host *host = dev_id;
628 struct mmc_request *mrq;
629 unsigned long iflags;
630
631 spin_lock_irqsave(&host->lock, iflags);
632 mrq = host->manual_stop_mrq;
633 spin_unlock_irqrestore(&host->lock, iflags);
634
635 if (!mrq) {
636 dev_err(mmc_dev(host->mmc), "no request for manual stop\n");
637 return IRQ_HANDLED;
638 }
639
640 dev_err(mmc_dev(host->mmc), "data error, sending stop command\n");
641
642 /*
643 * We will never have more than one outstanding request,
644 * and we do not complete the request until after
645 * we've cleared host->manual_stop_mrq so we do not need to
646 * spin lock this function.
647 * Additionally we have wait states within this function
648 * so having it in a lock is a very bad idea.
649 */
650 sunxi_mmc_send_manual_stop(host, mrq);
651
652 spin_lock_irqsave(&host->lock, iflags);
653 host->manual_stop_mrq = NULL;
654 spin_unlock_irqrestore(&host->lock, iflags);
655
656 mmc_request_done(host->mmc, mrq);
657
658 return IRQ_HANDLED;
659 }
660
661 static int sunxi_mmc_oclk_onoff(struct sunxi_mmc_host *host, u32 oclk_en)
662 {
663 unsigned long expire = jiffies + msecs_to_jiffies(750);
664 u32 rval;
665
666 dev_dbg(mmc_dev(host->mmc), "%sabling the clock\n",
667 oclk_en ? "en" : "dis");
668
669 rval = mmc_readl(host, REG_CLKCR);
670 rval &= ~(SDXC_CARD_CLOCK_ON | SDXC_LOW_POWER_ON | SDXC_MASK_DATA0);
671
672 if (oclk_en)
673 rval |= SDXC_CARD_CLOCK_ON;
674 if (host->cfg->mask_data0)
675 rval |= SDXC_MASK_DATA0;
676
677 mmc_writel(host, REG_CLKCR, rval);
678
679 rval = SDXC_START | SDXC_UPCLK_ONLY | SDXC_WAIT_PRE_OVER;
680 mmc_writel(host, REG_CMDR, rval);
681
682 do {
683 rval = mmc_readl(host, REG_CMDR);
684 } while (time_before(jiffies, expire) && (rval & SDXC_START));
685
686 /* clear irq status bits set by the command */
687 mmc_writel(host, REG_RINTR,
688 mmc_readl(host, REG_RINTR) & ~SDXC_SDIO_INTERRUPT);
689
690 if (rval & SDXC_START) {
691 dev_err(mmc_dev(host->mmc), "fatal err update clk timeout\n");
692 return -EIO;
693 }
694
695 if (host->cfg->mask_data0) {
696 rval = mmc_readl(host, REG_CLKCR);
697 mmc_writel(host, REG_CLKCR, rval & ~SDXC_MASK_DATA0);
698 }
699
700 return 0;
701 }
702
703 static int sunxi_mmc_calibrate(struct sunxi_mmc_host *host, int reg_off)
704 {
705 if (!host->cfg->can_calibrate)
706 return 0;
707
708 /*
709 * FIXME:
710 * This is not clear how the calibration is supposed to work
711 * yet. The best rate have been obtained by simply setting the
712 * delay to 0, as Allwinner does in its BSP.
713 *
714 * The only mode that doesn't have such a delay is HS400, that
715 * is in itself a TODO.
716 */
717 writel(SDXC_CAL_DL_SW_EN, host->reg_base + reg_off);
718
719 return 0;
720 }
721
722 static int sunxi_mmc_clk_set_phase(struct sunxi_mmc_host *host,
723 struct mmc_ios *ios, u32 rate)
724 {
725 int index;
726
727 /* clk controller delays not used under new timings mode */
728 if (host->use_new_timings)
729 return 0;
730
731 /* some old controllers don't support delays */
732 if (!host->cfg->clk_delays)
733 return 0;
734
735 /* determine delays */
736 if (rate <= 400000) {
737 index = SDXC_CLK_400K;
738 } else if (rate <= 25000000) {
739 index = SDXC_CLK_25M;
740 } else if (rate <= 52000000) {
741 if (ios->timing != MMC_TIMING_UHS_DDR50 &&
742 ios->timing != MMC_TIMING_MMC_DDR52) {
743 index = SDXC_CLK_50M;
744 } else if (ios->bus_width == MMC_BUS_WIDTH_8) {
745 index = SDXC_CLK_50M_DDR_8BIT;
746 } else {
747 index = SDXC_CLK_50M_DDR;
748 }
749 } else {
750 dev_dbg(mmc_dev(host->mmc), "Invalid clock... returning\n");
751 return -EINVAL;
752 }
753
754 clk_set_phase(host->clk_sample, host->cfg->clk_delays[index].sample);
755 clk_set_phase(host->clk_output, host->cfg->clk_delays[index].output);
756
757 return 0;
758 }
759
760 static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host,
761 struct mmc_ios *ios)
762 {
763 struct mmc_host *mmc = host->mmc;
764 long rate;
765 u32 rval, clock = ios->clock, div = 1;
766 int ret;
767
768 ret = sunxi_mmc_oclk_onoff(host, 0);
769 if (ret)
770 return ret;
771
772 /* Our clock is gated now */
773 mmc->actual_clock = 0;
774
775 if (!ios->clock)
776 return 0;
777
778 /*
779 * Under the old timing mode, 8 bit DDR requires the module
780 * clock to be double the card clock. Under the new timing
781 * mode, all DDR modes require a doubled module clock.
782 *
783 * We currently only support the standard MMC DDR52 mode.
784 * This block should be updated once support for other DDR
785 * modes is added.
786 */
787 if (ios->timing == MMC_TIMING_MMC_DDR52 &&
788 (host->use_new_timings ||
789 ios->bus_width == MMC_BUS_WIDTH_8)) {
790 div = 2;
791 clock <<= 1;
792 }
793
794 if (host->use_new_timings && host->cfg->ccu_has_timings_switch) {
795 ret = sunxi_ccu_set_mmc_timing_mode(host->clk_mmc, true);
796 if (ret) {
797 dev_err(mmc_dev(mmc),
798 "error setting new timing mode\n");
799 return ret;
800 }
801 }
802
803 rate = clk_round_rate(host->clk_mmc, clock);
804 if (rate < 0) {
805 dev_err(mmc_dev(mmc), "error rounding clk to %d: %ld\n",
806 clock, rate);
807 return rate;
808 }
809 dev_dbg(mmc_dev(mmc), "setting clk to %d, rounded %ld\n",
810 clock, rate);
811
812 /* setting clock rate */
813 ret = clk_set_rate(host->clk_mmc, rate);
814 if (ret) {
815 dev_err(mmc_dev(mmc), "error setting clk to %ld: %d\n",
816 rate, ret);
817 return ret;
818 }
819
820 /* set internal divider */
821 rval = mmc_readl(host, REG_CLKCR);
822 rval &= ~0xff;
823 rval |= div - 1;
824 mmc_writel(host, REG_CLKCR, rval);
825
826 /* update card clock rate to account for internal divider */
827 rate /= div;
828
829 /*
830 * Configure the controller to use the new timing mode if needed.
831 * On controllers that only support the new timing mode, such as
832 * the eMMC controller on the A64, this register does not exist,
833 * and any writes to it are ignored.
834 */
835 if (host->use_new_timings) {
836 /* Don't touch the delay bits */
837 rval = mmc_readl(host, REG_SD_NTSR);
838 rval |= SDXC_2X_TIMING_MODE;
839 mmc_writel(host, REG_SD_NTSR, rval);
840 }
841
842 /* sunxi_mmc_clk_set_phase expects the actual card clock rate */
843 ret = sunxi_mmc_clk_set_phase(host, ios, rate);
844 if (ret)
845 return ret;
846
847 ret = sunxi_mmc_calibrate(host, SDXC_REG_SAMP_DL_REG);
848 if (ret)
849 return ret;
850
851 /*
852 * FIXME:
853 *
854 * In HS400 we'll also need to calibrate the data strobe
855 * signal. This should only happen on the MMC2 controller (at
856 * least on the A64).
857 */
858
859 ret = sunxi_mmc_oclk_onoff(host, 1);
860 if (ret)
861 return ret;
862
863 /* And we just enabled our clock back */
864 mmc->actual_clock = rate;
865
866 return 0;
867 }
868
869 static void sunxi_mmc_set_bus_width(struct sunxi_mmc_host *host,
870 unsigned char width)
871 {
872 switch (width) {
873 case MMC_BUS_WIDTH_1:
874 mmc_writel(host, REG_WIDTH, SDXC_WIDTH1);
875 break;
876 case MMC_BUS_WIDTH_4:
877 mmc_writel(host, REG_WIDTH, SDXC_WIDTH4);
878 break;
879 case MMC_BUS_WIDTH_8:
880 mmc_writel(host, REG_WIDTH, SDXC_WIDTH8);
881 break;
882 }
883 }
884
885 static void sunxi_mmc_set_clk(struct sunxi_mmc_host *host, struct mmc_ios *ios)
886 {
887 u32 rval;
888
889 /* set ddr mode */
890 rval = mmc_readl(host, REG_GCTRL);
891 if (ios->timing == MMC_TIMING_UHS_DDR50 ||
892 ios->timing == MMC_TIMING_MMC_DDR52)
893 rval |= SDXC_DDR_MODE;
894 else
895 rval &= ~SDXC_DDR_MODE;
896 mmc_writel(host, REG_GCTRL, rval);
897
898 host->ferror = sunxi_mmc_clk_set_rate(host, ios);
899 /* Android code had a usleep_range(50000, 55000); here */
900 }
901
902 static void sunxi_mmc_card_power(struct sunxi_mmc_host *host,
903 struct mmc_ios *ios)
904 {
905 struct mmc_host *mmc = host->mmc;
906
907 switch (ios->power_mode) {
908 case MMC_POWER_UP:
909 dev_dbg(mmc_dev(mmc), "Powering card up\n");
910
911 if (!IS_ERR(mmc->supply.vmmc)) {
912 host->ferror = mmc_regulator_set_ocr(mmc,
913 mmc->supply.vmmc,
914 ios->vdd);
915 if (host->ferror)
916 return;
917 }
918
919 if (!IS_ERR(mmc->supply.vqmmc)) {
920 host->ferror = regulator_enable(mmc->supply.vqmmc);
921 if (host->ferror) {
922 dev_err(mmc_dev(mmc),
923 "failed to enable vqmmc\n");
924 return;
925 }
926 host->vqmmc_enabled = true;
927 }
928 break;
929
930 case MMC_POWER_OFF:
931 dev_dbg(mmc_dev(mmc), "Powering card off\n");
932
933 if (!IS_ERR(mmc->supply.vmmc))
934 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
935
936 if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled)
937 regulator_disable(mmc->supply.vqmmc);
938
939 host->vqmmc_enabled = false;
940 break;
941
942 default:
943 dev_dbg(mmc_dev(mmc), "Ignoring unknown card power state\n");
944 break;
945 }
946 }
947
948 static void sunxi_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
949 {
950 struct sunxi_mmc_host *host = mmc_priv(mmc);
951
952 sunxi_mmc_card_power(host, ios);
953 sunxi_mmc_set_bus_width(host, ios->bus_width);
954 sunxi_mmc_set_clk(host, ios);
955 }
956
957 static int sunxi_mmc_volt_switch(struct mmc_host *mmc, struct mmc_ios *ios)
958 {
959 int ret;
960
961 /* vqmmc regulator is available */
962 if (!IS_ERR(mmc->supply.vqmmc)) {
963 ret = mmc_regulator_set_vqmmc(mmc, ios);
964 return ret < 0 ? ret : 0;
965 }
966
967 /* no vqmmc regulator, assume fixed regulator at 3/3.3V */
968 if (mmc->ios.signal_voltage == MMC_SIGNAL_VOLTAGE_330)
969 return 0;
970
971 return -EINVAL;
972 }
973
974 static void sunxi_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
975 {
976 struct sunxi_mmc_host *host = mmc_priv(mmc);
977 unsigned long flags;
978 u32 imask;
979
980 if (enable)
981 pm_runtime_get_noresume(host->dev);
982
983 spin_lock_irqsave(&host->lock, flags);
984
985 imask = mmc_readl(host, REG_IMASK);
986 if (enable) {
987 host->sdio_imask = SDXC_SDIO_INTERRUPT;
988 imask |= SDXC_SDIO_INTERRUPT;
989 } else {
990 host->sdio_imask = 0;
991 imask &= ~SDXC_SDIO_INTERRUPT;
992 }
993 mmc_writel(host, REG_IMASK, imask);
994 spin_unlock_irqrestore(&host->lock, flags);
995
996 if (!enable)
997 pm_runtime_put_noidle(host->mmc->parent);
998 }
999
1000 static void sunxi_mmc_hw_reset(struct mmc_host *mmc)
1001 {
1002 struct sunxi_mmc_host *host = mmc_priv(mmc);
1003 mmc_writel(host, REG_HWRST, 0);
1004 udelay(10);
1005 mmc_writel(host, REG_HWRST, 1);
1006 udelay(300);
1007 }
1008
1009 static void sunxi_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
1010 {
1011 struct sunxi_mmc_host *host = mmc_priv(mmc);
1012 struct mmc_command *cmd = mrq->cmd;
1013 struct mmc_data *data = mrq->data;
1014 unsigned long iflags;
1015 u32 imask = SDXC_INTERRUPT_ERROR_BIT;
1016 u32 cmd_val = SDXC_START | (cmd->opcode & 0x3f);
1017 bool wait_dma = host->wait_dma;
1018 int ret;
1019
1020 /* Check for set_ios errors (should never happen) */
1021 if (host->ferror) {
1022 mrq->cmd->error = host->ferror;
1023 mmc_request_done(mmc, mrq);
1024 return;
1025 }
1026
1027 if (data) {
1028 ret = sunxi_mmc_map_dma(host, data);
1029 if (ret < 0) {
1030 dev_err(mmc_dev(mmc), "map DMA failed\n");
1031 cmd->error = ret;
1032 data->error = ret;
1033 mmc_request_done(mmc, mrq);
1034 return;
1035 }
1036 }
1037
1038 if (cmd->opcode == MMC_GO_IDLE_STATE) {
1039 cmd_val |= SDXC_SEND_INIT_SEQUENCE;
1040 imask |= SDXC_COMMAND_DONE;
1041 }
1042
1043 if (cmd->flags & MMC_RSP_PRESENT) {
1044 cmd_val |= SDXC_RESP_EXPIRE;
1045 if (cmd->flags & MMC_RSP_136)
1046 cmd_val |= SDXC_LONG_RESPONSE;
1047 if (cmd->flags & MMC_RSP_CRC)
1048 cmd_val |= SDXC_CHECK_RESPONSE_CRC;
1049
1050 if ((cmd->flags & MMC_CMD_MASK) == MMC_CMD_ADTC) {
1051 cmd_val |= SDXC_DATA_EXPIRE | SDXC_WAIT_PRE_OVER;
1052
1053 if (cmd->data->stop) {
1054 imask |= SDXC_AUTO_COMMAND_DONE;
1055 cmd_val |= SDXC_SEND_AUTO_STOP;
1056 } else {
1057 imask |= SDXC_DATA_OVER;
1058 }
1059
1060 if (cmd->data->flags & MMC_DATA_WRITE)
1061 cmd_val |= SDXC_WRITE;
1062 else
1063 wait_dma = true;
1064 } else {
1065 imask |= SDXC_COMMAND_DONE;
1066 }
1067 } else {
1068 imask |= SDXC_COMMAND_DONE;
1069 }
1070
1071 dev_dbg(mmc_dev(mmc), "cmd %d(%08x) arg %x ie 0x%08x len %d\n",
1072 cmd_val & 0x3f, cmd_val, cmd->arg, imask,
1073 mrq->data ? mrq->data->blksz * mrq->data->blocks : 0);
1074
1075 spin_lock_irqsave(&host->lock, iflags);
1076
1077 if (host->mrq || host->manual_stop_mrq) {
1078 spin_unlock_irqrestore(&host->lock, iflags);
1079
1080 if (data)
1081 dma_unmap_sg(mmc_dev(mmc), data->sg, data->sg_len,
1082 mmc_get_dma_dir(data));
1083
1084 dev_err(mmc_dev(mmc), "request already pending\n");
1085 mrq->cmd->error = -EBUSY;
1086 mmc_request_done(mmc, mrq);
1087 return;
1088 }
1089
1090 if (data) {
1091 mmc_writel(host, REG_BLKSZ, data->blksz);
1092 mmc_writel(host, REG_BCNTR, data->blksz * data->blocks);
1093 sunxi_mmc_start_dma(host, data);
1094 }
1095
1096 host->mrq = mrq;
1097 host->wait_dma = wait_dma;
1098 mmc_writel(host, REG_IMASK, host->sdio_imask | imask);
1099 mmc_writel(host, REG_CARG, cmd->arg);
1100 mmc_writel(host, REG_CMDR, cmd_val);
1101
1102 spin_unlock_irqrestore(&host->lock, iflags);
1103 }
1104
1105 static int sunxi_mmc_card_busy(struct mmc_host *mmc)
1106 {
1107 struct sunxi_mmc_host *host = mmc_priv(mmc);
1108
1109 return !!(mmc_readl(host, REG_STAS) & SDXC_CARD_DATA_BUSY);
1110 }
1111
1112 static const struct mmc_host_ops sunxi_mmc_ops = {
1113 .request = sunxi_mmc_request,
1114 .set_ios = sunxi_mmc_set_ios,
1115 .get_ro = mmc_gpio_get_ro,
1116 .get_cd = mmc_gpio_get_cd,
1117 .enable_sdio_irq = sunxi_mmc_enable_sdio_irq,
1118 .start_signal_voltage_switch = sunxi_mmc_volt_switch,
1119 .card_hw_reset = sunxi_mmc_hw_reset,
1120 .card_busy = sunxi_mmc_card_busy,
1121 };
1122
1123 static const struct sunxi_mmc_clk_delay sunxi_mmc_clk_delays[] = {
1124 [SDXC_CLK_400K] = { .output = 180, .sample = 180 },
1125 [SDXC_CLK_25M] = { .output = 180, .sample = 75 },
1126 [SDXC_CLK_50M] = { .output = 90, .sample = 120 },
1127 [SDXC_CLK_50M_DDR] = { .output = 60, .sample = 120 },
1128 /* Value from A83T "new timing mode". Works but might not be right. */
1129 [SDXC_CLK_50M_DDR_8BIT] = { .output = 90, .sample = 180 },
1130 };
1131
1132 static const struct sunxi_mmc_clk_delay sun9i_mmc_clk_delays[] = {
1133 [SDXC_CLK_400K] = { .output = 180, .sample = 180 },
1134 [SDXC_CLK_25M] = { .output = 180, .sample = 75 },
1135 [SDXC_CLK_50M] = { .output = 150, .sample = 120 },
1136 [SDXC_CLK_50M_DDR] = { .output = 54, .sample = 36 },
1137 [SDXC_CLK_50M_DDR_8BIT] = { .output = 72, .sample = 72 },
1138 };
1139
1140 static const struct sunxi_mmc_cfg sun4i_a10_cfg = {
1141 .idma_des_size_bits = 13,
1142 .clk_delays = NULL,
1143 .can_calibrate = false,
1144 };
1145
1146 static const struct sunxi_mmc_cfg sun5i_a13_cfg = {
1147 .idma_des_size_bits = 16,
1148 .clk_delays = NULL,
1149 .can_calibrate = false,
1150 };
1151
1152 static const struct sunxi_mmc_cfg sun7i_a20_cfg = {
1153 .idma_des_size_bits = 16,
1154 .clk_delays = sunxi_mmc_clk_delays,
1155 .can_calibrate = false,
1156 };
1157
1158 static const struct sunxi_mmc_cfg sun8i_a83t_emmc_cfg = {
1159 .idma_des_size_bits = 16,
1160 .clk_delays = sunxi_mmc_clk_delays,
1161 .can_calibrate = false,
1162 .ccu_has_timings_switch = true,
1163 };
1164
1165 static const struct sunxi_mmc_cfg sun9i_a80_cfg = {
1166 .idma_des_size_bits = 16,
1167 .clk_delays = sun9i_mmc_clk_delays,
1168 .can_calibrate = false,
1169 };
1170
1171 static const struct sunxi_mmc_cfg sun20i_d1_cfg = {
1172 .idma_des_size_bits = 13,
1173 .idma_des_shift = 2,
1174 .can_calibrate = true,
1175 .mask_data0 = true,
1176 .needs_new_timings = true,
1177 };
1178
1179 static const struct sunxi_mmc_cfg sun50i_a64_cfg = {
1180 .idma_des_size_bits = 16,
1181 .clk_delays = NULL,
1182 .can_calibrate = true,
1183 .mask_data0 = true,
1184 .needs_new_timings = true,
1185 };
1186
1187 static const struct sunxi_mmc_cfg sun50i_a64_emmc_cfg = {
1188 .idma_des_size_bits = 13,
1189 .clk_delays = NULL,
1190 .can_calibrate = true,
1191 .needs_new_timings = true,
1192 };
1193
1194 static const struct sunxi_mmc_cfg sun50i_h616_cfg = {
1195 .idma_des_size_bits = 16,
1196 .idma_des_shift = 2,
1197 .can_calibrate = true,
1198 .mask_data0 = true,
1199 .needs_new_timings = true,
1200 };
1201
1202 static const struct sunxi_mmc_cfg sun50i_a100_emmc_cfg = {
1203 .idma_des_size_bits = 13,
1204 .idma_des_shift = 2,
1205 .clk_delays = NULL,
1206 .can_calibrate = true,
1207 .needs_new_timings = true,
1208 };
1209
1210 static const struct of_device_id sunxi_mmc_of_match[] = {
1211 { .compatible = "allwinner,sun4i-a10-mmc", .data = &sun4i_a10_cfg },
1212 { .compatible = "allwinner,sun5i-a13-mmc", .data = &sun5i_a13_cfg },
1213 { .compatible = "allwinner,sun7i-a20-mmc", .data = &sun7i_a20_cfg },
1214 { .compatible = "allwinner,sun8i-a83t-emmc", .data = &sun8i_a83t_emmc_cfg },
1215 { .compatible = "allwinner,sun9i-a80-mmc", .data = &sun9i_a80_cfg },
1216 { .compatible = "allwinner,sun20i-d1-mmc", .data = &sun20i_d1_cfg },
1217 { .compatible = "allwinner,sun50i-a64-mmc", .data = &sun50i_a64_cfg },
1218 { .compatible = "allwinner,sun50i-a64-emmc", .data = &sun50i_a64_emmc_cfg },
1219 { .compatible = "allwinner,sun50i-a100-mmc", .data = &sun20i_d1_cfg },
1220 { .compatible = "allwinner,sun50i-a100-emmc", .data = &sun50i_a100_emmc_cfg },
1221 { .compatible = "allwinner,sun50i-h616-mmc", .data = &sun50i_h616_cfg },
1222 { /* sentinel */ }
1223 };
1224 MODULE_DEVICE_TABLE(of, sunxi_mmc_of_match);
1225
1226 static int sunxi_mmc_enable(struct sunxi_mmc_host *host)
1227 {
1228 int ret;
1229
1230 if (!IS_ERR(host->reset)) {
1231 ret = reset_control_reset(host->reset);
1232 if (ret) {
1233 dev_err(host->dev, "Couldn't reset the MMC controller (%d)\n",
1234 ret);
1235 return ret;
1236 }
1237 }
1238
1239 ret = clk_prepare_enable(host->clk_ahb);
1240 if (ret) {
1241 dev_err(host->dev, "Couldn't enable the bus clocks (%d)\n", ret);
1242 goto error_assert_reset;
1243 }
1244
1245 ret = clk_prepare_enable(host->clk_mmc);
1246 if (ret) {
1247 dev_err(host->dev, "Enable mmc clk err %d\n", ret);
1248 goto error_disable_clk_ahb;
1249 }
1250
1251 ret = clk_prepare_enable(host->clk_output);
1252 if (ret) {
1253 dev_err(host->dev, "Enable output clk err %d\n", ret);
1254 goto error_disable_clk_mmc;
1255 }
1256
1257 ret = clk_prepare_enable(host->clk_sample);
1258 if (ret) {
1259 dev_err(host->dev, "Enable sample clk err %d\n", ret);
1260 goto error_disable_clk_output;
1261 }
1262
1263 /*
1264 * Sometimes the controller asserts the irq on boot for some reason,
1265 * make sure the controller is in a sane state before enabling irqs.
1266 */
1267 ret = sunxi_mmc_reset_host(host);
1268 if (ret)
1269 goto error_disable_clk_sample;
1270
1271 return 0;
1272
1273 error_disable_clk_sample:
1274 clk_disable_unprepare(host->clk_sample);
1275 error_disable_clk_output:
1276 clk_disable_unprepare(host->clk_output);
1277 error_disable_clk_mmc:
1278 clk_disable_unprepare(host->clk_mmc);
1279 error_disable_clk_ahb:
1280 clk_disable_unprepare(host->clk_ahb);
1281 error_assert_reset:
1282 if (!IS_ERR(host->reset))
1283 reset_control_assert(host->reset);
1284 return ret;
1285 }
1286
1287 static void sunxi_mmc_disable(struct sunxi_mmc_host *host)
1288 {
1289 sunxi_mmc_reset_host(host);
1290
1291 clk_disable_unprepare(host->clk_sample);
1292 clk_disable_unprepare(host->clk_output);
1293 clk_disable_unprepare(host->clk_mmc);
1294 clk_disable_unprepare(host->clk_ahb);
1295
1296 if (!IS_ERR(host->reset))
1297 reset_control_assert(host->reset);
1298 }
1299
1300 static int sunxi_mmc_resource_request(struct sunxi_mmc_host *host,
1301 struct platform_device *pdev)
1302 {
1303 int ret;
1304
1305 host->cfg = of_device_get_match_data(&pdev->dev);
1306 if (!host->cfg)
1307 return -EINVAL;
1308
1309 ret = mmc_regulator_get_supply(host->mmc);
1310 if (ret)
1311 return ret;
1312
1313 host->reg_base = devm_platform_ioremap_resource(pdev, 0);
1314 if (IS_ERR(host->reg_base))
1315 return PTR_ERR(host->reg_base);
1316
1317 host->clk_ahb = devm_clk_get(&pdev->dev, "ahb");
1318 if (IS_ERR(host->clk_ahb)) {
1319 dev_err(&pdev->dev, "Could not get ahb clock\n");
1320 return PTR_ERR(host->clk_ahb);
1321 }
1322
1323 host->clk_mmc = devm_clk_get(&pdev->dev, "mmc");
1324 if (IS_ERR(host->clk_mmc)) {
1325 dev_err(&pdev->dev, "Could not get mmc clock\n");
1326 return PTR_ERR(host->clk_mmc);
1327 }
1328
1329 if (host->cfg->clk_delays) {
1330 host->clk_output = devm_clk_get(&pdev->dev, "output");
1331 if (IS_ERR(host->clk_output)) {
1332 dev_err(&pdev->dev, "Could not get output clock\n");
1333 return PTR_ERR(host->clk_output);
1334 }
1335
1336 host->clk_sample = devm_clk_get(&pdev->dev, "sample");
1337 if (IS_ERR(host->clk_sample)) {
1338 dev_err(&pdev->dev, "Could not get sample clock\n");
1339 return PTR_ERR(host->clk_sample);
1340 }
1341 }
1342
1343 host->reset = devm_reset_control_get_optional_exclusive(&pdev->dev,
1344 "ahb");
1345 if (PTR_ERR(host->reset) == -EPROBE_DEFER)
1346 return PTR_ERR(host->reset);
1347
1348 ret = sunxi_mmc_enable(host);
1349 if (ret)
1350 return ret;
1351
1352 host->irq = platform_get_irq(pdev, 0);
1353 if (host->irq < 0) {
1354 ret = host->irq;
1355 goto error_disable_mmc;
1356 }
1357
1358 return devm_request_threaded_irq(&pdev->dev, host->irq, sunxi_mmc_irq,
1359 sunxi_mmc_handle_manual_stop, 0, "sunxi-mmc", host);
1360
1361 error_disable_mmc:
1362 sunxi_mmc_disable(host);
1363 return ret;
1364 }
1365
1366 static int sunxi_mmc_probe(struct platform_device *pdev)
1367 {
1368 struct sunxi_mmc_host *host;
1369 struct mmc_host *mmc;
1370 int ret;
1371
1372 mmc = mmc_alloc_host(sizeof(struct sunxi_mmc_host), &pdev->dev);
1373 if (!mmc) {
1374 dev_err(&pdev->dev, "mmc alloc host failed\n");
1375 return -ENOMEM;
1376 }
1377 platform_set_drvdata(pdev, mmc);
1378
1379 host = mmc_priv(mmc);
1380 host->dev = &pdev->dev;
1381 host->mmc = mmc;
1382 spin_lock_init(&host->lock);
1383
1384 ret = sunxi_mmc_resource_request(host, pdev);
1385 if (ret)
1386 goto error_free_host;
1387
1388 host->sg_cpu = dma_alloc_coherent(&pdev->dev, PAGE_SIZE,
1389 &host->sg_dma, GFP_KERNEL);
1390 if (!host->sg_cpu) {
1391 dev_err(&pdev->dev, "Failed to allocate DMA descriptor mem\n");
1392 ret = -ENOMEM;
1393 goto error_free_host;
1394 }
1395
1396 if (host->cfg->ccu_has_timings_switch) {
1397 /*
1398 * Supports both old and new timing modes.
1399 * Try setting the clk to new timing mode.
1400 */
1401 sunxi_ccu_set_mmc_timing_mode(host->clk_mmc, true);
1402
1403 /* And check the result */
1404 ret = sunxi_ccu_get_mmc_timing_mode(host->clk_mmc);
1405 if (ret < 0) {
1406 /*
1407 * For whatever reason we were not able to get
1408 * the current active mode. Default to old mode.
1409 */
1410 dev_warn(&pdev->dev, "MMC clk timing mode unknown\n");
1411 host->use_new_timings = false;
1412 } else {
1413 host->use_new_timings = !!ret;
1414 }
1415 } else if (host->cfg->needs_new_timings) {
1416 /* Supports new timing mode only */
1417 host->use_new_timings = true;
1418 }
1419
1420 mmc->ops = &sunxi_mmc_ops;
1421 mmc->max_blk_count = 8192;
1422 mmc->max_blk_size = 4096;
1423 mmc->max_segs = PAGE_SIZE / sizeof(struct sunxi_idma_des);
1424 mmc->max_seg_size = (1 << host->cfg->idma_des_size_bits);
1425 mmc->max_req_size = mmc->max_seg_size * mmc->max_segs;
1426 /* 400kHz ~ 52MHz */
1427 mmc->f_min = 400000;
1428 mmc->f_max = 52000000;
1429 mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
1430 MMC_CAP_SDIO_IRQ;
1431
1432 /*
1433 * Some H5 devices do not have signal traces precise enough to
1434 * use HS DDR mode for their eMMC chips.
1435 *
1436 * We still enable HS DDR modes for all the other controller
1437 * variants that support them.
1438 */
1439 if ((host->cfg->clk_delays || host->use_new_timings) &&
1440 !of_device_is_compatible(pdev->dev.of_node,
1441 "allwinner,sun50i-h5-emmc"))
1442 mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR;
1443
1444 ret = mmc_of_parse(mmc);
1445 if (ret)
1446 goto error_free_dma;
1447
1448 /*
1449 * If we don't support delay chains in the SoC, we can't use any
1450 * of the higher speed modes. Mask them out in case the device
1451 * tree specifies the properties for them, which gets added to
1452 * the caps by mmc_of_parse() above.
1453 */
1454 if (!(host->cfg->clk_delays || host->use_new_timings)) {
1455 mmc->caps &= ~(MMC_CAP_3_3V_DDR | MMC_CAP_1_8V_DDR |
1456 MMC_CAP_1_2V_DDR | MMC_CAP_UHS);
1457 mmc->caps2 &= ~MMC_CAP2_HS200;
1458 }
1459
1460 /* TODO: This driver doesn't support HS400 mode yet */
1461 mmc->caps2 &= ~MMC_CAP2_HS400;
1462
1463 ret = sunxi_mmc_init_host(host);
1464 if (ret)
1465 goto error_free_dma;
1466
1467 pm_runtime_set_active(&pdev->dev);
1468 pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
1469 pm_runtime_use_autosuspend(&pdev->dev);
1470 pm_runtime_enable(&pdev->dev);
1471
1472 ret = mmc_add_host(mmc);
1473 if (ret)
1474 goto error_free_dma;
1475
1476 dev_info(&pdev->dev, "initialized, max. request size: %u KB%s\n",
1477 mmc->max_req_size >> 10,
1478 host->use_new_timings ? ", uses new timings mode" : "");
1479
1480 return 0;
1481
1482 error_free_dma:
1483 dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
1484 error_free_host:
1485 mmc_free_host(mmc);
1486 return ret;
1487 }
1488
1489 static void sunxi_mmc_remove(struct platform_device *pdev)
1490 {
1491 struct mmc_host *mmc = platform_get_drvdata(pdev);
1492 struct sunxi_mmc_host *host = mmc_priv(mmc);
1493
1494 mmc_remove_host(mmc);
1495 pm_runtime_disable(&pdev->dev);
1496 if (!pm_runtime_status_suspended(&pdev->dev)) {
1497 disable_irq(host->irq);
1498 sunxi_mmc_disable(host);
1499 }
1500 dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
1501 mmc_free_host(mmc);
1502 }
1503
1504 #ifdef CONFIG_PM
1505 static int sunxi_mmc_runtime_resume(struct device *dev)
1506 {
1507 struct mmc_host *mmc = dev_get_drvdata(dev);
1508 struct sunxi_mmc_host *host = mmc_priv(mmc);
1509 int ret;
1510
1511 ret = sunxi_mmc_enable(host);
1512 if (ret)
1513 return ret;
1514
1515 sunxi_mmc_init_host(host);
1516 sunxi_mmc_set_bus_width(host, mmc->ios.bus_width);
1517 sunxi_mmc_set_clk(host, &mmc->ios);
1518 enable_irq(host->irq);
1519
1520 return 0;
1521 }
1522
1523 static int sunxi_mmc_runtime_suspend(struct device *dev)
1524 {
1525 struct mmc_host *mmc = dev_get_drvdata(dev);
1526 struct sunxi_mmc_host *host = mmc_priv(mmc);
1527
1528 /*
1529 * When clocks are off, it's possible receiving
1530 * fake interrupts, which will stall the system.
1531 * Disabling the irq will prevent this.
1532 */
1533 disable_irq(host->irq);
1534 sunxi_mmc_reset_host(host);
1535 sunxi_mmc_disable(host);
1536
1537 return 0;
1538 }
1539 #endif
1540
1541 static const struct dev_pm_ops sunxi_mmc_pm_ops = {
1542 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
1543 pm_runtime_force_resume)
1544 SET_RUNTIME_PM_OPS(sunxi_mmc_runtime_suspend,
1545 sunxi_mmc_runtime_resume,
1546 NULL)
1547 };
1548
1549 static struct platform_driver sunxi_mmc_driver = {
1550 .driver = {
1551 .name = "sunxi-mmc",
1552 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
1553 .of_match_table = sunxi_mmc_of_match,
1554 .pm = &sunxi_mmc_pm_ops,
1555 },
1556 .probe = sunxi_mmc_probe,
1557 .remove = sunxi_mmc_remove,
1558 };
1559 module_platform_driver(sunxi_mmc_driver);
1560
1561 MODULE_DESCRIPTION("Allwinner's SD/MMC Card Controller Driver");
1562 MODULE_LICENSE("GPL v2");
1563 MODULE_AUTHOR("David Lanzendörfer <david.lanzendoerfer@o2s.ch>");
1564 MODULE_ALIAS("platform:sunxi-mmc");
Kernel DRM miscellaneous fixes and cross-tree changes