printf: Remove unused 'bprintf'

[drm/drm-misc.git] / drivers / phy / mediatek / phy-mtk-tphy.c

// SPDX-License-Identifier: GPL-2.0
/*
 * Copyright (c) 2015 MediaTek Inc.
 * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
 *
 */

#include <dt-bindings/phy/phy.h>
#include <linux/clk.h>
#include <linux/debugfs.h>
#include <linux/delay.h>
#include <linux/iopoll.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/nvmem-consumer.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>

#include "phy-mtk-io.h"

/* version V1 sub-banks offset base address */
/* banks shared by multiple phys */
#define SSUSB_SIFSLV_V1_SPLLC           0x000   /* shared by u3 phys */
#define SSUSB_SIFSLV_V1_U2FREQ          0x100   /* shared by u2 phys */
#define SSUSB_SIFSLV_V1_CHIP            0x300   /* shared by u3 phys */
/* u2 phy bank */
#define SSUSB_SIFSLV_V1_U2PHY_COM       0x000
/* u3/pcie/sata phy banks */
#define SSUSB_SIFSLV_V1_U3PHYD          0x000
#define SSUSB_SIFSLV_V1_U3PHYA          0x200

/* version V2/V3 sub-banks offset base address */
/* V3: U2FREQ is not used anymore, but reserved */
/* u2 phy banks */
#define SSUSB_SIFSLV_V2_MISC            0x000
#define SSUSB_SIFSLV_V2_U2FREQ          0x100
#define SSUSB_SIFSLV_V2_U2PHY_COM       0x300
/* u3/pcie/sata phy banks */
#define SSUSB_SIFSLV_V2_SPLLC           0x000
#define SSUSB_SIFSLV_V2_CHIP            0x100
#define SSUSB_SIFSLV_V2_U3PHYD          0x200
#define SSUSB_SIFSLV_V2_U3PHYA          0x400

#define U3P_MISC_REG1           0x04
#define MR1_EFUSE_AUTO_LOAD_DIS         BIT(6)

#define U3P_USBPHYACR0          0x000
#define PA0_RG_U2PLL_FORCE_ON           BIT(15)
#define PA0_USB20_PLL_PREDIV            GENMASK(7, 6)
#define PA0_RG_USB20_INTR_EN            BIT(5)

#define U3P_USBPHYACR1          0x004
#define PA1_RG_INTR_CAL         GENMASK(23, 19)
#define PA1_RG_VRT_SEL                  GENMASK(14, 12)
#define PA1_RG_TERM_SEL         GENMASK(10, 8)

#define U3P_USBPHYACR2          0x008
#define PA2_RG_U2PLL_BW                 GENMASK(21, 19)
#define PA2_RG_SIF_U2PLL_FORCE_EN       BIT(18)

#define U3P_USBPHYACR5          0x014
#define PA5_RG_U2_HSTX_SRCAL_EN BIT(15)
#define PA5_RG_U2_HSTX_SRCTRL           GENMASK(14, 12)
#define PA5_RG_U2_HS_100U_U3_EN BIT(11)

#define U3P_USBPHYACR6          0x018
#define PA6_RG_U2_PRE_EMP               GENMASK(31, 30)
#define PA6_RG_U2_BC11_SW_EN            BIT(23)
#define PA6_RG_U2_OTG_VBUSCMP_EN        BIT(20)
#define PA6_RG_U2_DISCTH                GENMASK(7, 4)
#define PA6_RG_U2_SQTH          GENMASK(3, 0)

#define U3P_U2PHYACR4           0x020
#define P2C_RG_USB20_GPIO_CTL           BIT(9)
#define P2C_USB20_GPIO_MODE             BIT(8)
#define P2C_U2_GPIO_CTR_MSK     (P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)

#define U3P_U2PHYA_RESV         0x030
#define P2R_RG_U2PLL_FBDIV_26M          0x1bb13b
#define P2R_RG_U2PLL_FBDIV_48M          0x3c0000

#define U3P_U2PHYA_RESV1        0x044
#define P2R_RG_U2PLL_REFCLK_SEL BIT(5)
#define P2R_RG_U2PLL_FRA_EN             BIT(3)

#define U3D_U2PHYDCR0           0x060
#define P2C_RG_SIF_U2PLL_FORCE_ON       BIT(24)

#define U3P_U2PHYDTM0           0x068
#define P2C_FORCE_UART_EN               BIT(26)
#define P2C_FORCE_DATAIN                BIT(23)
#define P2C_FORCE_DM_PULLDOWN           BIT(21)
#define P2C_FORCE_DP_PULLDOWN           BIT(20)
#define P2C_FORCE_XCVRSEL               BIT(19)
#define P2C_FORCE_SUSPENDM              BIT(18)
#define P2C_FORCE_TERMSEL               BIT(17)
#define P2C_RG_DATAIN                   GENMASK(13, 10)
#define P2C_RG_DMPULLDOWN               BIT(7)
#define P2C_RG_DPPULLDOWN               BIT(6)
#define P2C_RG_XCVRSEL                  GENMASK(5, 4)
#define P2C_RG_SUSPENDM                 BIT(3)
#define P2C_RG_TERMSEL                  BIT(2)
#define P2C_DTM0_PART_MASK \
                (P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
                P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
                P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
                P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)

#define U3P_U2PHYDTM1           0x06C
#define P2C_RG_UART_EN                  BIT(16)
#define P2C_FORCE_IDDIG         BIT(9)
#define P2C_RG_VBUSVALID                BIT(5)
#define P2C_RG_SESSEND                  BIT(4)
#define P2C_RG_AVALID                   BIT(2)
#define P2C_RG_IDDIG                    BIT(1)

#define U3P_U2PHYBC12C          0x080
#define P2C_RG_CHGDT_EN         BIT(0)

#define U3P_U3_CHIP_GPIO_CTLD           0x0c
#define P3C_REG_IP_SW_RST               BIT(31)
#define P3C_MCU_BUS_CK_GATE_EN          BIT(30)
#define P3C_FORCE_IP_SW_RST             BIT(29)

#define U3P_U3_CHIP_GPIO_CTLE           0x10
#define P3C_RG_SWRST_U3_PHYD            BIT(25)
#define P3C_RG_SWRST_U3_PHYD_FORCE_EN   BIT(24)

#define U3P_U3_PHYA_REG0        0x000
#define P3A_RG_IEXT_INTR                GENMASK(15, 10)
#define P3A_RG_CLKDRV_OFF               GENMASK(3, 2)

#define U3P_U3_PHYA_REG1        0x004
#define P3A_RG_CLKDRV_AMP               GENMASK(31, 29)

#define U3P_U3_PHYA_REG6        0x018
#define P3A_RG_TX_EIDLE_CM              GENMASK(31, 28)

#define U3P_U3_PHYA_REG9        0x024
#define P3A_RG_RX_DAC_MUX               GENMASK(5, 1)

#define U3P_U3_PHYA_DA_REG0     0x100
#define P3A_RG_XTAL_EXT_PE2H            GENMASK(17, 16)
#define P3A_RG_XTAL_EXT_PE1H            GENMASK(13, 12)
#define P3A_RG_XTAL_EXT_EN_U3           GENMASK(11, 10)

#define U3P_U3_PHYA_DA_REG4     0x108
#define P3A_RG_PLL_DIVEN_PE2H           GENMASK(21, 19)
#define P3A_RG_PLL_BC_PE2H              GENMASK(7, 6)

#define U3P_U3_PHYA_DA_REG5     0x10c
#define P3A_RG_PLL_BR_PE2H              GENMASK(29, 28)
#define P3A_RG_PLL_IC_PE2H              GENMASK(15, 12)

#define U3P_U3_PHYA_DA_REG6     0x110
#define P3A_RG_PLL_IR_PE2H              GENMASK(19, 16)

#define U3P_U3_PHYA_DA_REG7     0x114
#define P3A_RG_PLL_BP_PE2H              GENMASK(19, 16)

#define U3P_U3_PHYA_DA_REG20    0x13c
#define P3A_RG_PLL_DELTA1_PE2H          GENMASK(31, 16)

#define U3P_U3_PHYA_DA_REG25    0x148
#define P3A_RG_PLL_DELTA_PE2H           GENMASK(15, 0)

#define U3P_U3_PHYD_LFPS1               0x00c
#define P3D_RG_FWAKE_TH         GENMASK(21, 16)

#define U3P_U3_PHYD_IMPCAL0             0x010
#define P3D_RG_FORCE_TX_IMPEL           BIT(31)
#define P3D_RG_TX_IMPEL                 GENMASK(28, 24)

#define U3P_U3_PHYD_IMPCAL1             0x014
#define P3D_RG_FORCE_RX_IMPEL           BIT(31)
#define P3D_RG_RX_IMPEL                 GENMASK(28, 24)

#define U3P_U3_PHYD_RSV                 0x054
#define P3D_RG_EFUSE_AUTO_LOAD_DIS      BIT(12)

#define U3P_U3_PHYD_CDR1                0x05c
#define P3D_RG_CDR_BIR_LTD1             GENMASK(28, 24)
#define P3D_RG_CDR_BIR_LTD0             GENMASK(12, 8)

#define U3P_U3_PHYD_TOP1                0x100
#define P3D_RG_PHY_MODE                 GENMASK(2, 1)
#define P3D_RG_FORCE_PHY_MODE           BIT(0)

#define U3P_U3_PHYD_RXDET1              0x128
#define P3D_RG_RXDET_STB2_SET           GENMASK(17, 9)

#define U3P_U3_PHYD_RXDET2              0x12c
#define P3D_RG_RXDET_STB2_SET_P3        GENMASK(8, 0)

#define U3P_SPLLC_XTALCTL3              0x018
#define XC3_RG_U3_XTAL_RX_PWD           BIT(9)
#define XC3_RG_U3_FRC_XTAL_RX_PWD       BIT(8)

#define U3P_U2FREQ_FMCR0        0x00
#define P2F_RG_MONCLK_SEL       GENMASK(27, 26)
#define P2F_RG_FREQDET_EN       BIT(24)
#define P2F_RG_CYCLECNT         GENMASK(23, 0)

#define U3P_U2FREQ_VALUE        0x0c

#define U3P_U2FREQ_FMMONR1      0x10
#define P2F_USB_FM_VALID        BIT(0)
#define P2F_RG_FRCK_EN          BIT(8)

#define U3P_REF_CLK             26      /* MHZ */
#define U3P_SLEW_RATE_COEF      28
#define U3P_SR_COEF_DIVISOR     1000
#define U3P_FM_DET_CYCLE_CNT    1024

/* SATA register setting */
#define PHYD_CTRL_SIGNAL_MODE4          0x1c
/* CDR Charge Pump P-path current adjustment */
#define RG_CDR_BICLTD1_GEN1_MSK         GENMASK(23, 20)
#define RG_CDR_BICLTD0_GEN1_MSK         GENMASK(11, 8)

#define PHYD_DESIGN_OPTION2             0x24
/* Symbol lock count selection */
#define RG_LOCK_CNT_SEL_MSK             GENMASK(5, 4)

#define PHYD_DESIGN_OPTION9     0x40
/* COMWAK GAP width window */
#define RG_TG_MAX_MSK           GENMASK(20, 16)
/* COMINIT GAP width window */
#define RG_T2_MAX_MSK           GENMASK(13, 8)
/* COMWAK GAP width window */
#define RG_TG_MIN_MSK           GENMASK(7, 5)
/* COMINIT GAP width window */
#define RG_T2_MIN_MSK           GENMASK(4, 0)

#define ANA_RG_CTRL_SIGNAL1             0x4c
/* TX driver tail current control for 0dB de-empahsis mdoe for Gen1 speed */
#define RG_IDRV_0DB_GEN1_MSK            GENMASK(13, 8)

#define ANA_RG_CTRL_SIGNAL4             0x58
#define RG_CDR_BICLTR_GEN1_MSK          GENMASK(23, 20)
/* Loop filter R1 resistance adjustment for Gen1 speed */
#define RG_CDR_BR_GEN2_MSK              GENMASK(10, 8)

#define ANA_RG_CTRL_SIGNAL6             0x60
/* I-path capacitance adjustment for Gen1 */
#define RG_CDR_BC_GEN1_MSK              GENMASK(28, 24)
#define RG_CDR_BIRLTR_GEN1_MSK          GENMASK(4, 0)

#define ANA_EQ_EYE_CTRL_SIGNAL1         0x6c
/* RX Gen1 LEQ tuning step */
#define RG_EQ_DLEQ_LFI_GEN1_MSK         GENMASK(11, 8)

#define ANA_EQ_EYE_CTRL_SIGNAL4         0xd8
#define RG_CDR_BIRLTD0_GEN1_MSK         GENMASK(20, 16)

#define ANA_EQ_EYE_CTRL_SIGNAL5         0xdc
#define RG_CDR_BIRLTD0_GEN3_MSK         GENMASK(4, 0)

/* PHY switch between pcie/usb3/sgmii/sata */
#define USB_PHY_SWITCH_CTRL     0x0
#define RG_PHY_SW_TYPE          GENMASK(3, 0)
#define RG_PHY_SW_PCIE          0x0
#define RG_PHY_SW_USB3          0x1
#define RG_PHY_SW_SGMII         0x2
#define RG_PHY_SW_SATA          0x3

#define TPHY_CLKS_CNT   2

#define USER_BUF_LEN(count) min_t(size_t, 8, (count))

enum mtk_phy_version {
        MTK_PHY_V1 = 1,
        MTK_PHY_V2,
        MTK_PHY_V3,
};

struct mtk_phy_pdata {
        /* avoid RX sensitivity level degradation only for mt8173 */
        bool avoid_rx_sen_degradation;
        /*
         * workaround only for mt8195, HW fix it for others of V3,
         * u2phy should use integer mode instead of fractional mode of
         * 48M PLL, fix it by switching PLL to 26M from default 48M
         */
        bool sw_pll_48m_to_26m;
        /*
         * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse,
         * support sw way, also support it for v2/v3 optionally.
         */
        bool sw_efuse_supported;
        enum mtk_phy_version version;
};

struct u2phy_banks {
        void __iomem *misc;
        void __iomem *fmreg;
        void __iomem *com;
};

struct u3phy_banks {
        void __iomem *spllc;
        void __iomem *chip;
        void __iomem *phyd; /* include u3phyd_bank2 */
        void __iomem *phya; /* include u3phya_da */
};

struct mtk_phy_instance {
        struct phy *phy;
        void __iomem *port_base;
        union {
                struct u2phy_banks u2_banks;
                struct u3phy_banks u3_banks;
        };
        struct clk_bulk_data clks[TPHY_CLKS_CNT];
        u32 index;
        u32 type;
        struct regmap *type_sw;
        u32 type_sw_reg;
        u32 type_sw_index;
        u32 efuse_sw_en;
        u32 efuse_intr;
        u32 efuse_tx_imp;
        u32 efuse_rx_imp;
        int eye_src;
        int eye_vrt;
        int eye_term;
        int intr;
        int discth;
        int pre_emphasis;
        bool bc12_en;
        bool type_force_mode;
};

struct mtk_tphy {
        struct device *dev;
        void __iomem *sif_base; /* only shared sif */
        const struct mtk_phy_pdata *pdata;
        struct mtk_phy_instance **phys;
        int nphys;
        int src_ref_clk; /* MHZ, reference clock for slew rate calibrate */
        int src_coef; /* coefficient for slew rate calibrate */
};

#if IS_ENABLED(CONFIG_DEBUG_FS)

enum u2_phy_params {
        U2P_EYE_VRT = 0,
        U2P_EYE_TERM,
        U2P_EFUSE_EN,
        U2P_EFUSE_INTR,
        U2P_DISCTH,
        U2P_PRE_EMPHASIS,
};

enum u3_phy_params {
        U3P_EFUSE_EN = 0,
        U3P_EFUSE_INTR,
        U3P_EFUSE_TX_IMP,
        U3P_EFUSE_RX_IMP,
};

static const char *const u2_phy_files[] = {
        [U2P_EYE_VRT] = "vrt",
        [U2P_EYE_TERM] = "term",
        [U2P_EFUSE_EN] = "efuse",
        [U2P_EFUSE_INTR] = "intr",
        [U2P_DISCTH] = "discth",
        [U2P_PRE_EMPHASIS] = "preemph",
};

static const char *const u3_phy_files[] = {
        [U3P_EFUSE_EN] = "efuse",
        [U3P_EFUSE_INTR] = "intr",
        [U3P_EFUSE_TX_IMP] = "tx-imp",
        [U3P_EFUSE_RX_IMP] = "rx-imp",
};

static int u2_phy_params_show(struct seq_file *sf, void *unused)
{
        struct mtk_phy_instance *inst = sf->private;
        const char *fname = file_dentry(sf->file)->d_iname;
        struct u2phy_banks *u2_banks = &inst->u2_banks;
        void __iomem *com = u2_banks->com;
        u32 max = 0;
        u32 tmp = 0;
        u32 val = 0;
        int ret;

        ret = match_string(u2_phy_files, ARRAY_SIZE(u2_phy_files), fname);
        if (ret < 0)
                return ret;

        switch (ret) {
        case U2P_EYE_VRT:
                tmp = readl(com + U3P_USBPHYACR1);
                val = FIELD_GET(PA1_RG_VRT_SEL, tmp);
                max = FIELD_MAX(PA1_RG_VRT_SEL);
                break;

        case U2P_EYE_TERM:
                tmp = readl(com + U3P_USBPHYACR1);
                val = FIELD_GET(PA1_RG_TERM_SEL, tmp);
                max = FIELD_MAX(PA1_RG_TERM_SEL);
                break;

        case U2P_EFUSE_EN:
                if (u2_banks->misc) {
                        tmp = readl(u2_banks->misc + U3P_MISC_REG1);
                        max = 1;
                }

                val = !!(tmp & MR1_EFUSE_AUTO_LOAD_DIS);
                break;

        case U2P_EFUSE_INTR:
                tmp = readl(com + U3P_USBPHYACR1);
                val = FIELD_GET(PA1_RG_INTR_CAL, tmp);
                max = FIELD_MAX(PA1_RG_INTR_CAL);
                break;

        case U2P_DISCTH:
                tmp = readl(com + U3P_USBPHYACR6);
                val = FIELD_GET(PA6_RG_U2_DISCTH, tmp);
                max = FIELD_MAX(PA6_RG_U2_DISCTH);
                break;

        case U2P_PRE_EMPHASIS:
                tmp = readl(com + U3P_USBPHYACR6);
                val = FIELD_GET(PA6_RG_U2_PRE_EMP, tmp);
                max = FIELD_MAX(PA6_RG_U2_PRE_EMP);
                break;

        default:
                seq_printf(sf, "invalid, %d\n", ret);
                break;
        }

        seq_printf(sf, "%s : %d [0, %d]\n", fname, val, max);

        return 0;
}

static int u2_phy_params_open(struct inode *inode, struct file *file)
{
        return single_open(file, u2_phy_params_show, inode->i_private);
}

static ssize_t u2_phy_params_write(struct file *file, const char __user *ubuf,
                                   size_t count, loff_t *ppos)
{
        const char *fname = file_dentry(file)->d_iname;
        struct seq_file *sf = file->private_data;
        struct mtk_phy_instance *inst = sf->private;
        struct u2phy_banks *u2_banks = &inst->u2_banks;
        void __iomem *com = u2_banks->com;
        ssize_t rc;
        u32 val;
        int ret;

        rc = kstrtouint_from_user(ubuf, USER_BUF_LEN(count), 0, &val);
        if (rc)
                return rc;

        ret = match_string(u2_phy_files, ARRAY_SIZE(u2_phy_files), fname);
        if (ret < 0)
                return (ssize_t)ret;

        switch (ret) {
        case U2P_EYE_VRT:
                mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_VRT_SEL, val);
                break;

        case U2P_EYE_TERM:
                mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_TERM_SEL, val);
                break;

        case U2P_EFUSE_EN:
                if (u2_banks->misc)
                        mtk_phy_update_field(u2_banks->misc + U3P_MISC_REG1,
                                             MR1_EFUSE_AUTO_LOAD_DIS, !!val);
                break;

        case U2P_EFUSE_INTR:
                mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_INTR_CAL, val);
                break;

        case U2P_DISCTH:
                mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_DISCTH, val);
                break;

        case U2P_PRE_EMPHASIS:
                mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_PRE_EMP, val);
                break;

        default:
                break;
        }

        return count;
}

static const struct file_operations u2_phy_fops = {
        .open = u2_phy_params_open,
        .write = u2_phy_params_write,
        .read = seq_read,
        .llseek = seq_lseek,
        .release = single_release,
};

static void u2_phy_dbgfs_files_create(struct mtk_phy_instance *inst)
{
        u32 count = ARRAY_SIZE(u2_phy_files);
        int i;

        for (i = 0; i < count; i++)
                debugfs_create_file(u2_phy_files[i], 0644, inst->phy->debugfs,
                                    inst, &u2_phy_fops);
}

static int u3_phy_params_show(struct seq_file *sf, void *unused)
{
        struct mtk_phy_instance *inst = sf->private;
        const char *fname = file_dentry(sf->file)->d_iname;
        struct u3phy_banks *u3_banks = &inst->u3_banks;
        u32 val = 0;
        u32 max = 0;
        u32 tmp;
        int ret;

        ret = match_string(u3_phy_files, ARRAY_SIZE(u3_phy_files), fname);
        if (ret < 0)
                return ret;

        switch (ret) {
        case U3P_EFUSE_EN:
                tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV);
                val = !!(tmp & P3D_RG_EFUSE_AUTO_LOAD_DIS);
                max = 1;
                break;

        case U3P_EFUSE_INTR:
                tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0);
                val = FIELD_GET(P3A_RG_IEXT_INTR, tmp);
                max = FIELD_MAX(P3A_RG_IEXT_INTR);
                break;

        case U3P_EFUSE_TX_IMP:
                tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0);
                val = FIELD_GET(P3D_RG_TX_IMPEL, tmp);
                max = FIELD_MAX(P3D_RG_TX_IMPEL);
                break;

        case U3P_EFUSE_RX_IMP:
                tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1);
                val = FIELD_GET(P3D_RG_RX_IMPEL, tmp);
                max = FIELD_MAX(P3D_RG_RX_IMPEL);
                break;

        default:
                seq_printf(sf, "invalid, %d\n", ret);
                break;
        }

        seq_printf(sf, "%s : %d [0, %d]\n", fname, val, max);

        return 0;
}

static int u3_phy_params_open(struct inode *inode, struct file *file)
{
        return single_open(file, u3_phy_params_show, inode->i_private);
}

static ssize_t u3_phy_params_write(struct file *file, const char __user *ubuf,
                                   size_t count, loff_t *ppos)
{
        const char *fname = file_dentry(file)->d_iname;
        struct seq_file *sf = file->private_data;
        struct mtk_phy_instance *inst = sf->private;
        struct u3phy_banks *u3_banks = &inst->u3_banks;
        void __iomem *phyd = u3_banks->phyd;
        ssize_t rc;
        u32 val;
        int ret;

        rc = kstrtouint_from_user(ubuf, USER_BUF_LEN(count), 0, &val);
        if (rc)
                return rc;

        ret = match_string(u3_phy_files, ARRAY_SIZE(u3_phy_files), fname);
        if (ret < 0)
                return (ssize_t)ret;

        switch (ret) {
        case U3P_EFUSE_EN:
                mtk_phy_update_field(phyd + U3P_U3_PHYD_RSV,
                                     P3D_RG_EFUSE_AUTO_LOAD_DIS, !!val);
                break;

        case U3P_EFUSE_INTR:
                mtk_phy_update_field(u3_banks->phya + U3P_U3_PHYA_REG0,
                                     P3A_RG_IEXT_INTR, val);
                break;

        case U3P_EFUSE_TX_IMP:
                mtk_phy_update_field(phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_TX_IMPEL, val);
                mtk_phy_set_bits(phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_FORCE_TX_IMPEL);
                break;

        case U3P_EFUSE_RX_IMP:
                mtk_phy_update_field(phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_RX_IMPEL, val);
                mtk_phy_set_bits(phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_FORCE_RX_IMPEL);
                break;

        default:
                break;
        }

        return count;
}

static const struct file_operations u3_phy_fops = {
        .open = u3_phy_params_open,
        .write = u3_phy_params_write,
        .read = seq_read,
        .llseek = seq_lseek,
        .release = single_release,
};

static void u3_phy_dbgfs_files_create(struct mtk_phy_instance *inst)
{
        u32 count = ARRAY_SIZE(u3_phy_files);
        int i;

        for (i = 0; i < count; i++)
                debugfs_create_file(u3_phy_files[i], 0644, inst->phy->debugfs,
                                    inst, &u3_phy_fops);
}

static int phy_type_show(struct seq_file *sf, void *unused)
{
        struct mtk_phy_instance *inst = sf->private;
        const char *type;

        switch (inst->type) {
        case PHY_TYPE_USB2:
                type = "USB2";
                break;
        case PHY_TYPE_USB3:
                type = "USB3";
                break;
        case PHY_TYPE_PCIE:
                type = "PCIe";
                break;
        case PHY_TYPE_SGMII:
                type = "SGMII";
                break;
        case PHY_TYPE_SATA:
                type = "SATA";
                break;
        default:
                type = "";
        }

        seq_printf(sf, "%s\n", type);

        return 0;
}
DEFINE_SHOW_ATTRIBUTE(phy_type);

/* these files will be removed when phy is released by phy core */
static void phy_debugfs_init(struct mtk_phy_instance *inst)
{
        debugfs_create_file("type", 0444, inst->phy->debugfs, inst, &phy_type_fops);

        switch (inst->type) {
        case PHY_TYPE_USB2:
                u2_phy_dbgfs_files_create(inst);
                break;
        case PHY_TYPE_USB3:
        case PHY_TYPE_PCIE:
                u3_phy_dbgfs_files_create(inst);
                break;
        default:
                break;
        }
}

#else

static void phy_debugfs_init(struct mtk_phy_instance *inst)
{}

#endif

static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        void __iomem *fmreg = u2_banks->fmreg;
        void __iomem *com = u2_banks->com;
        int calibration_val;
        int fm_out;
        u32 tmp;

        /* HW V3 doesn't support slew rate cal anymore */
        if (tphy->pdata->version == MTK_PHY_V3)
                return;

        /* use force value */
        if (instance->eye_src)
                return;

        /* enable USB ring oscillator */
        mtk_phy_set_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN);
        udelay(1);

        /*enable free run clock */
        mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);

        /* set cycle count as 1024, and select u2 channel */
        tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
        tmp &= ~(P2F_RG_CYCLECNT | P2F_RG_MONCLK_SEL);
        tmp |= FIELD_PREP(P2F_RG_CYCLECNT, U3P_FM_DET_CYCLE_CNT);
        if (tphy->pdata->version == MTK_PHY_V1)
                tmp |= FIELD_PREP(P2F_RG_MONCLK_SEL, instance->index >> 1);

        writel(tmp, fmreg + U3P_U2FREQ_FMCR0);

        /* enable frequency meter */
        mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);

        /* ignore return value */
        readl_poll_timeout(fmreg + U3P_U2FREQ_FMMONR1, tmp,
                           (tmp & P2F_USB_FM_VALID), 10, 200);

        fm_out = readl(fmreg + U3P_U2FREQ_VALUE);

        /* disable frequency meter */
        mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);

        /*disable free run clock */
        mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);

        if (fm_out) {
                /* ( 1024 / FM_OUT ) x reference clock frequency x coef */
                tmp = tphy->src_ref_clk * tphy->src_coef;
                tmp = (tmp * U3P_FM_DET_CYCLE_CNT) / fm_out;
                calibration_val = DIV_ROUND_CLOSEST(tmp, U3P_SR_COEF_DIVISOR);
        } else {
                /* if FM detection fail, set default value */
                calibration_val = 4;
        }
        dev_dbg(tphy->dev, "phy:%d, fm_out:%d, calib:%d (clk:%d, coef:%d)\n",
                instance->index, fm_out, calibration_val,
                tphy->src_ref_clk, tphy->src_coef);

        /* set HS slew rate */
        mtk_phy_update_field(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL,
                             calibration_val);

        /* disable USB ring oscillator */
        mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN);
}

static void u3_phy_instance_init(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u3phy_banks *u3_banks = &instance->u3_banks;
        void __iomem *phya = u3_banks->phya;
        void __iomem *phyd = u3_banks->phyd;

        if (instance->type_force_mode) {
                /* force phy as usb mode, default is pcie rc mode */
                mtk_phy_update_field(phyd + U3P_U3_PHYD_TOP1, P3D_RG_PHY_MODE, 1);
                mtk_phy_set_bits(phyd + U3P_U3_PHYD_TOP1, P3D_RG_FORCE_PHY_MODE);
                /* power down phy by ip and pipe reset */
                mtk_phy_set_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLD,
                                 P3C_FORCE_IP_SW_RST | P3C_MCU_BUS_CK_GATE_EN);
                mtk_phy_set_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLE,
                                 P3C_RG_SWRST_U3_PHYD | P3C_RG_SWRST_U3_PHYD_FORCE_EN);
                udelay(10);
                /* power on phy again */
                mtk_phy_clear_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLD,
                                   P3C_FORCE_IP_SW_RST | P3C_MCU_BUS_CK_GATE_EN);
                mtk_phy_clear_bits(u3_banks->chip + U3P_U3_CHIP_GPIO_CTLE,
                                   P3C_RG_SWRST_U3_PHYD | P3C_RG_SWRST_U3_PHYD_FORCE_EN);
        }

        /* gating PCIe Analog XTAL clock */
        mtk_phy_set_bits(u3_banks->spllc + U3P_SPLLC_XTALCTL3,
                         XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD);

        /* gating XSQ */
        mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG0, P3A_RG_XTAL_EXT_EN_U3, 2);

        mtk_phy_update_field(phya + U3P_U3_PHYA_REG9, P3A_RG_RX_DAC_MUX, 4);

        mtk_phy_update_field(phya + U3P_U3_PHYA_REG6, P3A_RG_TX_EIDLE_CM, 0xe);

        mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_CDR1,
                            P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1,
                            FIELD_PREP(P3D_RG_CDR_BIR_LTD0, 0xc) |
                            FIELD_PREP(P3D_RG_CDR_BIR_LTD1, 0x3));

        mtk_phy_update_field(phyd + U3P_U3_PHYD_LFPS1, P3D_RG_FWAKE_TH, 0x34);

        mtk_phy_update_field(phyd + U3P_U3_PHYD_RXDET1, P3D_RG_RXDET_STB2_SET, 0x10);

        mtk_phy_update_field(phyd + U3P_U3_PHYD_RXDET2, P3D_RG_RXDET_STB2_SET_P3, 0x10);

        dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
}

static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        void __iomem *com = u2_banks->com;

        if (!tphy->pdata->sw_pll_48m_to_26m)
                return;

        mtk_phy_update_field(com + U3P_USBPHYACR0, PA0_USB20_PLL_PREDIV, 0);

        mtk_phy_update_field(com + U3P_USBPHYACR2, PA2_RG_U2PLL_BW, 3);

        writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);

        mtk_phy_set_bits(com + U3P_U2PHYA_RESV1,
                         P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL);
}

static void u2_phy_instance_init(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        void __iomem *com = u2_banks->com;
        u32 index = instance->index;

        /* switch to USB function, and enable usb pll */
        mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_UART_EN | P2C_FORCE_SUSPENDM);

        mtk_phy_clear_bits(com + U3P_U2PHYDTM0,
                           P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK);

        mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_UART_EN);

        mtk_phy_set_bits(com + U3P_USBPHYACR0, PA0_RG_USB20_INTR_EN);

        /* disable switch 100uA current to SSUSB */
        mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN);

        mtk_phy_clear_bits(com + U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK);

        if (tphy->pdata->avoid_rx_sen_degradation) {
                if (!index) {
                        mtk_phy_set_bits(com + U3P_USBPHYACR2, PA2_RG_SIF_U2PLL_FORCE_EN);

                        mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
                } else {
                        mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);

                        mtk_phy_set_bits(com + U3P_U2PHYDTM0,
                                         P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
                }
        }

        /* DP/DM BC1.1 path Disable */
        mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN);

        mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_SQTH, 2);

        /* Workaround only for mt8195, HW fix it for others (V3) */
        u2_phy_pll_26m_set(tphy, instance);

        dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
}

static void u2_phy_instance_power_on(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        void __iomem *com = u2_banks->com;
        u32 index = instance->index;

        /* OTG Enable */
        mtk_phy_set_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);

        mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);

        mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND);

        if (tphy->pdata->avoid_rx_sen_degradation && index) {
                mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);

                mtk_phy_set_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
        }
        dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
}

static void u2_phy_instance_power_off(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        void __iomem *com = u2_banks->com;
        u32 index = instance->index;

        /* OTG Disable */
        mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);

        mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);

        mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND);

        if (tphy->pdata->avoid_rx_sen_degradation && index) {
                mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);

                mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
        }

        dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
}

static void u2_phy_instance_exit(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        void __iomem *com = u2_banks->com;
        u32 index = instance->index;

        if (tphy->pdata->avoid_rx_sen_degradation && index) {
                mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);

                mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM);
        }
}

static void u2_phy_instance_set_mode(struct mtk_tphy *tphy,
                                     struct mtk_phy_instance *instance,
                                     enum phy_mode mode)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        u32 tmp;

        tmp = readl(u2_banks->com + U3P_U2PHYDTM1);
        switch (mode) {
        case PHY_MODE_USB_DEVICE:
                tmp |= P2C_FORCE_IDDIG | P2C_RG_IDDIG;
                break;
        case PHY_MODE_USB_HOST:
                tmp |= P2C_FORCE_IDDIG;
                tmp &= ~P2C_RG_IDDIG;
                break;
        case PHY_MODE_USB_OTG:
                tmp &= ~(P2C_FORCE_IDDIG | P2C_RG_IDDIG);
                break;
        default:
                return;
        }
        writel(tmp, u2_banks->com + U3P_U2PHYDTM1);
}

static void pcie_phy_instance_init(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u3phy_banks *u3_banks = &instance->u3_banks;
        void __iomem *phya = u3_banks->phya;

        if (tphy->pdata->version != MTK_PHY_V1)
                return;

        mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG0,
                            P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H,
                            FIELD_PREP(P3A_RG_XTAL_EXT_PE1H, 0x2) |
                            FIELD_PREP(P3A_RG_XTAL_EXT_PE2H, 0x2));

        /* ref clk drive */
        mtk_phy_update_field(phya + U3P_U3_PHYA_REG1, P3A_RG_CLKDRV_AMP, 0x4);

        mtk_phy_update_field(phya + U3P_U3_PHYA_REG0, P3A_RG_CLKDRV_OFF, 0x1);

        /* SSC delta -5000ppm */
        mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG20, P3A_RG_PLL_DELTA1_PE2H, 0x3c);

        mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG25, P3A_RG_PLL_DELTA_PE2H, 0x36);

        /* change pll BW 0.6M */
        mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG5,
                            P3A_RG_PLL_BR_PE2H | P3A_RG_PLL_IC_PE2H,
                            FIELD_PREP(P3A_RG_PLL_BR_PE2H, 0x1) |
                            FIELD_PREP(P3A_RG_PLL_IC_PE2H, 0x1));

        mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG4,
                            P3A_RG_PLL_DIVEN_PE2H | P3A_RG_PLL_BC_PE2H,
                            FIELD_PREP(P3A_RG_PLL_BC_PE2H, 0x3));

        mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG6, P3A_RG_PLL_IR_PE2H, 0x2);

        mtk_phy_update_field(phya + U3P_U3_PHYA_DA_REG7, P3A_RG_PLL_BP_PE2H, 0xa);

        /* Tx Detect Rx Timing: 10us -> 5us */
        mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_RXDET1,
                             P3D_RG_RXDET_STB2_SET, 0x10);

        mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_RXDET2,
                             P3D_RG_RXDET_STB2_SET_P3, 0x10);

        /* wait for PCIe subsys register to active */
        usleep_range(2500, 3000);
        dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
}

static void pcie_phy_instance_power_on(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u3phy_banks *bank = &instance->u3_banks;

        mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD,
                           P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);

        mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE,
                           P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
}

static void pcie_phy_instance_power_off(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)

{
        struct u3phy_banks *bank = &instance->u3_banks;

        mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD,
                         P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);

        mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE,
                         P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
}

static void sata_phy_instance_init(struct mtk_tphy *tphy,
        struct mtk_phy_instance *instance)
{
        struct u3phy_banks *u3_banks = &instance->u3_banks;
        void __iomem *phyd = u3_banks->phyd;

        /* charge current adjustment */
        mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL6,
                            RG_CDR_BIRLTR_GEN1_MSK | RG_CDR_BC_GEN1_MSK,
                            FIELD_PREP(RG_CDR_BIRLTR_GEN1_MSK, 0x6) |
                            FIELD_PREP(RG_CDR_BC_GEN1_MSK, 0x1a));

        mtk_phy_update_field(phyd + ANA_EQ_EYE_CTRL_SIGNAL4, RG_CDR_BIRLTD0_GEN1_MSK, 0x18);

        mtk_phy_update_field(phyd + ANA_EQ_EYE_CTRL_SIGNAL5, RG_CDR_BIRLTD0_GEN3_MSK, 0x06);

        mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL4,
                            RG_CDR_BICLTR_GEN1_MSK | RG_CDR_BR_GEN2_MSK,
                            FIELD_PREP(RG_CDR_BICLTR_GEN1_MSK, 0x0c) |
                            FIELD_PREP(RG_CDR_BR_GEN2_MSK, 0x07));

        mtk_phy_update_bits(phyd + PHYD_CTRL_SIGNAL_MODE4,
                            RG_CDR_BICLTD0_GEN1_MSK | RG_CDR_BICLTD1_GEN1_MSK,
                            FIELD_PREP(RG_CDR_BICLTD0_GEN1_MSK, 0x08) |
                            FIELD_PREP(RG_CDR_BICLTD1_GEN1_MSK, 0x02));

        mtk_phy_update_field(phyd + PHYD_DESIGN_OPTION2, RG_LOCK_CNT_SEL_MSK, 0x02);

        mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9,
                            RG_T2_MIN_MSK | RG_TG_MIN_MSK,
                            FIELD_PREP(RG_T2_MIN_MSK, 0x12) |
                            FIELD_PREP(RG_TG_MIN_MSK, 0x04));

        mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9,
                            RG_T2_MAX_MSK | RG_TG_MAX_MSK,
                            FIELD_PREP(RG_T2_MAX_MSK, 0x31) |
                            FIELD_PREP(RG_TG_MAX_MSK, 0x0e));

        mtk_phy_update_field(phyd + ANA_RG_CTRL_SIGNAL1, RG_IDRV_0DB_GEN1_MSK, 0x20);

        mtk_phy_update_field(phyd + ANA_EQ_EYE_CTRL_SIGNAL1, RG_EQ_DLEQ_LFI_GEN1_MSK, 0x03);

        dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
}

static void phy_v1_banks_init(struct mtk_tphy *tphy,
                              struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        struct u3phy_banks *u3_banks = &instance->u3_banks;

        switch (instance->type) {
        case PHY_TYPE_USB2:
                u2_banks->misc = NULL;
                u2_banks->fmreg = tphy->sif_base + SSUSB_SIFSLV_V1_U2FREQ;
                u2_banks->com = instance->port_base + SSUSB_SIFSLV_V1_U2PHY_COM;
                break;
        case PHY_TYPE_USB3:
        case PHY_TYPE_PCIE:
                u3_banks->spllc = tphy->sif_base + SSUSB_SIFSLV_V1_SPLLC;
                u3_banks->chip = tphy->sif_base + SSUSB_SIFSLV_V1_CHIP;
                u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
                u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V1_U3PHYA;
                break;
        case PHY_TYPE_SATA:
                u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
                break;
        default:
                dev_err(tphy->dev, "incompatible PHY type\n");
                return;
        }
}

static void phy_v2_banks_init(struct mtk_tphy *tphy,
                              struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        struct u3phy_banks *u3_banks = &instance->u3_banks;

        switch (instance->type) {
        case PHY_TYPE_USB2:
                u2_banks->misc = instance->port_base + SSUSB_SIFSLV_V2_MISC;
                u2_banks->fmreg = instance->port_base + SSUSB_SIFSLV_V2_U2FREQ;
                u2_banks->com = instance->port_base + SSUSB_SIFSLV_V2_U2PHY_COM;
                break;
        case PHY_TYPE_USB3:
        case PHY_TYPE_PCIE:
                u3_banks->spllc = instance->port_base + SSUSB_SIFSLV_V2_SPLLC;
                u3_banks->chip = instance->port_base + SSUSB_SIFSLV_V2_CHIP;
                u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V2_U3PHYD;
                u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V2_U3PHYA;
                break;
        default:
                dev_err(tphy->dev, "incompatible PHY type\n");
                return;
        }
}

static void phy_parse_property(struct mtk_tphy *tphy,
                                struct mtk_phy_instance *instance)
{
        struct device *dev = &instance->phy->dev;

        if (instance->type == PHY_TYPE_USB3)
                instance->type_force_mode = device_property_read_bool(dev, "mediatek,force-mode");

        if (instance->type != PHY_TYPE_USB2)
                return;

        instance->bc12_en = device_property_read_bool(dev, "mediatek,bc12");
        device_property_read_u32(dev, "mediatek,eye-src",
                                 &instance->eye_src);
        device_property_read_u32(dev, "mediatek,eye-vrt",
                                 &instance->eye_vrt);
        device_property_read_u32(dev, "mediatek,eye-term",
                                 &instance->eye_term);
        device_property_read_u32(dev, "mediatek,intr",
                                 &instance->intr);
        device_property_read_u32(dev, "mediatek,discth",
                                 &instance->discth);
        device_property_read_u32(dev, "mediatek,pre-emphasis",
                                 &instance->pre_emphasis);
        dev_dbg(dev, "bc12:%d, src:%d, vrt:%d, term:%d, intr:%d, disc:%d\n",
                instance->bc12_en, instance->eye_src,
                instance->eye_vrt, instance->eye_term,
                instance->intr, instance->discth);
        dev_dbg(dev, "pre-emp:%d\n", instance->pre_emphasis);
}

static void u2_phy_props_set(struct mtk_tphy *tphy,
                             struct mtk_phy_instance *instance)
{
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        void __iomem *com = u2_banks->com;

        if (instance->bc12_en) /* BC1.2 path Enable */
                mtk_phy_set_bits(com + U3P_U2PHYBC12C, P2C_RG_CHGDT_EN);

        if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src)
                mtk_phy_update_field(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL,
                                     instance->eye_src);

        if (instance->eye_vrt)
                mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_VRT_SEL,
                                     instance->eye_vrt);

        if (instance->eye_term)
                mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_TERM_SEL,
                                     instance->eye_term);

        if (instance->intr) {
                if (u2_banks->misc)
                        mtk_phy_set_bits(u2_banks->misc + U3P_MISC_REG1,
                                         MR1_EFUSE_AUTO_LOAD_DIS);

                mtk_phy_update_field(com + U3P_USBPHYACR1, PA1_RG_INTR_CAL,
                                     instance->intr);
        }

        if (instance->discth)
                mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_DISCTH,
                                     instance->discth);

        if (instance->pre_emphasis)
                mtk_phy_update_field(com + U3P_USBPHYACR6, PA6_RG_U2_PRE_EMP,
                                     instance->pre_emphasis);
}

/* type switch for usb3/pcie/sgmii/sata */
static int phy_type_syscon_get(struct mtk_phy_instance *instance,
                               struct device_node *dn)
{
        struct of_phandle_args args;
        int ret;

        /* type switch function is optional */
        if (!of_property_read_bool(dn, "mediatek,syscon-type"))
                return 0;

        ret = of_parse_phandle_with_fixed_args(dn, "mediatek,syscon-type",
                                               2, 0, &args);
        if (ret)
                return ret;

        instance->type_sw_reg = args.args[0];
        instance->type_sw_index = args.args[1] & 0x3; /* <=3 */
        instance->type_sw = syscon_node_to_regmap(args.np);
        of_node_put(args.np);
        dev_info(&instance->phy->dev, "type_sw - reg %#x, index %d\n",
                 instance->type_sw_reg, instance->type_sw_index);

        return PTR_ERR_OR_ZERO(instance->type_sw);
}

static int phy_type_set(struct mtk_phy_instance *instance)
{
        int type;
        u32 offset;

        if (!instance->type_sw)
                return 0;

        switch (instance->type) {
        case PHY_TYPE_USB3:
                type = RG_PHY_SW_USB3;
                break;
        case PHY_TYPE_PCIE:
                type = RG_PHY_SW_PCIE;
                break;
        case PHY_TYPE_SGMII:
                type = RG_PHY_SW_SGMII;
                break;
        case PHY_TYPE_SATA:
                type = RG_PHY_SW_SATA;
                break;
        case PHY_TYPE_USB2:
        default:
                return 0;
        }

        offset = instance->type_sw_index * BITS_PER_BYTE;
        regmap_update_bits(instance->type_sw, instance->type_sw_reg,
                           RG_PHY_SW_TYPE << offset, type << offset);

        return 0;
}

static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance)
{
        struct device *dev = &instance->phy->dev;
        int ret = 0;

        /* tphy v1 doesn't support sw efuse, skip it */
        if (!tphy->pdata->sw_efuse_supported) {
                instance->efuse_sw_en = 0;
                return 0;
        }

        /* software efuse is optional */
        instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells");
        if (!instance->efuse_sw_en)
                return 0;

        switch (instance->type) {
        case PHY_TYPE_USB2:
                ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
                if (ret) {
                        dev_err(dev, "fail to get u2 intr efuse, %d\n", ret);
                        break;
                }

                /* no efuse, ignore it */
                if (!instance->efuse_intr) {
                        dev_warn(dev, "no u2 intr efuse, but dts enable it\n");
                        instance->efuse_sw_en = 0;
                        break;
                }

                dev_dbg(dev, "u2 efuse - intr %x\n", instance->efuse_intr);
                break;

        case PHY_TYPE_USB3:
        case PHY_TYPE_PCIE:
                ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
                if (ret) {
                        dev_err(dev, "fail to get u3 intr efuse, %d\n", ret);
                        break;
                }

                ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp);
                if (ret) {
                        dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret);
                        break;
                }

                ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp);
                if (ret) {
                        dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret);
                        break;
                }

                /* no efuse, ignore it */
                if (!instance->efuse_intr &&
                    !instance->efuse_rx_imp &&
                    !instance->efuse_tx_imp) {
                        dev_warn(dev, "no u3 intr efuse, but dts enable it\n");
                        instance->efuse_sw_en = 0;
                        break;
                }

                dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n",
                        instance->efuse_intr, instance->efuse_rx_imp,instance->efuse_tx_imp);
                break;
        default:
                dev_err(dev, "no sw efuse for type %d\n", instance->type);
                ret = -EINVAL;
        }

        return ret;
}

static void phy_efuse_set(struct mtk_phy_instance *instance)
{
        struct device *dev = &instance->phy->dev;
        struct u2phy_banks *u2_banks = &instance->u2_banks;
        struct u3phy_banks *u3_banks = &instance->u3_banks;

        if (!instance->efuse_sw_en)
                return;

        switch (instance->type) {
        case PHY_TYPE_USB2:
                mtk_phy_set_bits(u2_banks->misc + U3P_MISC_REG1, MR1_EFUSE_AUTO_LOAD_DIS);

                mtk_phy_update_field(u2_banks->com + U3P_USBPHYACR1, PA1_RG_INTR_CAL,
                                     instance->efuse_intr);
                break;
        case PHY_TYPE_USB3:
        case PHY_TYPE_PCIE:
                mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_RSV, P3D_RG_EFUSE_AUTO_LOAD_DIS);

                mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_TX_IMPEL,
                                    instance->efuse_tx_imp);
                mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_FORCE_TX_IMPEL);

                mtk_phy_update_field(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_RX_IMPEL,
                                    instance->efuse_rx_imp);
                mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_FORCE_RX_IMPEL);

                mtk_phy_update_field(u3_banks->phya + U3P_U3_PHYA_REG0, P3A_RG_IEXT_INTR,
                                    instance->efuse_intr);
                break;
        default:
                dev_warn(dev, "no sw efuse for type %d\n", instance->type);
                break;
        }
}

static int mtk_phy_init(struct phy *phy)
{
        struct mtk_phy_instance *instance = phy_get_drvdata(phy);
        struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
        int ret;

        ret = clk_bulk_prepare_enable(TPHY_CLKS_CNT, instance->clks);
        if (ret)
                return ret;

        phy_efuse_set(instance);

        switch (instance->type) {
        case PHY_TYPE_USB2:
                u2_phy_instance_init(tphy, instance);
                u2_phy_props_set(tphy, instance);
                break;
        case PHY_TYPE_USB3:
                u3_phy_instance_init(tphy, instance);
                break;
        case PHY_TYPE_PCIE:
                pcie_phy_instance_init(tphy, instance);
                break;
        case PHY_TYPE_SATA:
                sata_phy_instance_init(tphy, instance);
                break;
        case PHY_TYPE_SGMII:
                /* nothing to do, only used to set type */
                break;
        default:
                dev_err(tphy->dev, "incompatible PHY type\n");
                clk_bulk_disable_unprepare(TPHY_CLKS_CNT, instance->clks);
                return -EINVAL;
        }

        return 0;
}

static int mtk_phy_power_on(struct phy *phy)
{
        struct mtk_phy_instance *instance = phy_get_drvdata(phy);
        struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);

        if (instance->type == PHY_TYPE_USB2) {
                u2_phy_instance_power_on(tphy, instance);
                hs_slew_rate_calibrate(tphy, instance);
        } else if (instance->type == PHY_TYPE_PCIE) {
                pcie_phy_instance_power_on(tphy, instance);
        }

        return 0;
}

static int mtk_phy_power_off(struct phy *phy)
{
        struct mtk_phy_instance *instance = phy_get_drvdata(phy);
        struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);

        if (instance->type == PHY_TYPE_USB2)
                u2_phy_instance_power_off(tphy, instance);
        else if (instance->type == PHY_TYPE_PCIE)
                pcie_phy_instance_power_off(tphy, instance);

        return 0;
}

static int mtk_phy_exit(struct phy *phy)
{
        struct mtk_phy_instance *instance = phy_get_drvdata(phy);
        struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);

        if (instance->type == PHY_TYPE_USB2)
                u2_phy_instance_exit(tphy, instance);

        clk_bulk_disable_unprepare(TPHY_CLKS_CNT, instance->clks);
        return 0;
}

static int mtk_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode)
{
        struct mtk_phy_instance *instance = phy_get_drvdata(phy);
        struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);

        if (instance->type == PHY_TYPE_USB2)
                u2_phy_instance_set_mode(tphy, instance, mode);

        return 0;
}

static struct phy *mtk_phy_xlate(struct device *dev,
                                        const struct of_phandle_args *args)
{
        struct mtk_tphy *tphy = dev_get_drvdata(dev);
        struct mtk_phy_instance *instance = NULL;
        struct device_node *phy_np = args->np;
        int index;
        int ret;

        if (args->args_count != 1) {
                dev_err(dev, "invalid number of cells in 'phy' property\n");
                return ERR_PTR(-EINVAL);
        }

        for (index = 0; index < tphy->nphys; index++)
                if (phy_np == tphy->phys[index]->phy->dev.of_node) {
                        instance = tphy->phys[index];
                        break;
                }

        if (!instance) {
                dev_err(dev, "failed to find appropriate phy\n");
                return ERR_PTR(-EINVAL);
        }

        instance->type = args->args[0];
        if (!(instance->type == PHY_TYPE_USB2 ||
              instance->type == PHY_TYPE_USB3 ||
              instance->type == PHY_TYPE_PCIE ||
              instance->type == PHY_TYPE_SATA ||
              instance->type == PHY_TYPE_SGMII)) {
                dev_err(dev, "unsupported device type: %d\n", instance->type);
                return ERR_PTR(-EINVAL);
        }

        switch (tphy->pdata->version) {
        case MTK_PHY_V1:
                phy_v1_banks_init(tphy, instance);
                break;
        case MTK_PHY_V2:
        case MTK_PHY_V3:
                phy_v2_banks_init(tphy, instance);
                break;
        default:
                dev_err(dev, "phy version is not supported\n");
                return ERR_PTR(-EINVAL);
        }

        ret = phy_efuse_get(tphy, instance);
        if (ret)
                return ERR_PTR(ret);

        phy_parse_property(tphy, instance);
        phy_type_set(instance);
        phy_debugfs_init(instance);

        return instance->phy;
}

static const struct phy_ops mtk_tphy_ops = {
        .init           = mtk_phy_init,
        .exit           = mtk_phy_exit,
        .power_on       = mtk_phy_power_on,
        .power_off      = mtk_phy_power_off,
        .set_mode       = mtk_phy_set_mode,
        .owner          = THIS_MODULE,
};

static const struct mtk_phy_pdata tphy_v1_pdata = {
        .avoid_rx_sen_degradation = false,
        .version = MTK_PHY_V1,
};

static const struct mtk_phy_pdata tphy_v2_pdata = {
        .avoid_rx_sen_degradation = false,
        .sw_efuse_supported = true,
        .version = MTK_PHY_V2,
};

static const struct mtk_phy_pdata tphy_v3_pdata = {
        .sw_efuse_supported = true,
        .version = MTK_PHY_V3,
};

static const struct mtk_phy_pdata mt8173_pdata = {
        .avoid_rx_sen_degradation = true,
        .version = MTK_PHY_V1,
};

static const struct mtk_phy_pdata mt8195_pdata = {
        .sw_pll_48m_to_26m = true,
        .sw_efuse_supported = true,
        .version = MTK_PHY_V3,
};

static const struct of_device_id mtk_tphy_id_table[] = {
        { .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata },
        { .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata },
        { .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
        { .compatible = "mediatek,mt8195-tphy", .data = &mt8195_pdata },
        { .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
        { .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
        { .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
        { },
};
MODULE_DEVICE_TABLE(of, mtk_tphy_id_table);

static int mtk_tphy_probe(struct platform_device *pdev)
{
        struct device *dev = &pdev->dev;
        struct device_node *np = dev->of_node;
        struct phy_provider *provider;
        struct resource *sif_res;
        struct mtk_tphy *tphy;
        struct resource res;
        int port;

        tphy = devm_kzalloc(dev, sizeof(*tphy), GFP_KERNEL);
        if (!tphy)
                return -ENOMEM;

        tphy->pdata = of_device_get_match_data(dev);
        if (!tphy->pdata)
                return -EINVAL;

        tphy->nphys = of_get_child_count(np);
        tphy->phys = devm_kcalloc(dev, tphy->nphys,
                                       sizeof(*tphy->phys), GFP_KERNEL);
        if (!tphy->phys)
                return -ENOMEM;

        tphy->dev = dev;
        platform_set_drvdata(pdev, tphy);

        sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        /* SATA phy of V1 needn't it if not shared with PCIe or USB */
        if (sif_res && tphy->pdata->version == MTK_PHY_V1) {
                /* get banks shared by multiple phys */
                tphy->sif_base = devm_ioremap_resource(dev, sif_res);
                if (IS_ERR(tphy->sif_base)) {
                        dev_err(dev, "failed to remap sif regs\n");
                        return PTR_ERR(tphy->sif_base);
                }
        }

        if (tphy->pdata->version < MTK_PHY_V3) {
                tphy->src_ref_clk = U3P_REF_CLK;
                tphy->src_coef = U3P_SLEW_RATE_COEF;
                /* update parameters of slew rate calibrate if exist */
                device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
                                         &tphy->src_ref_clk);
                device_property_read_u32(dev, "mediatek,src-coef",
                                         &tphy->src_coef);
        }

        port = 0;
        for_each_child_of_node_scoped(np, child_np) {
                struct mtk_phy_instance *instance;
                struct clk_bulk_data *clks;
                struct device *subdev;
                struct phy *phy;
                int retval;

                instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
                if (!instance)
                        return -ENOMEM;

                tphy->phys[port] = instance;

                phy = devm_phy_create(dev, child_np, &mtk_tphy_ops);
                if (IS_ERR(phy)) {
                        dev_err(dev, "failed to create phy\n");
                        return PTR_ERR(phy);
                }

                subdev = &phy->dev;
                retval = of_address_to_resource(child_np, 0, &res);
                if (retval) {
                        dev_err(subdev, "failed to get address resource(id-%d)\n",
                                port);
                        return retval;
                }

                instance->port_base = devm_ioremap_resource(subdev, &res);
                if (IS_ERR(instance->port_base))
                        return PTR_ERR(instance->port_base);

                instance->phy = phy;
                instance->index = port;
                phy_set_drvdata(phy, instance);
                port++;

                clks = instance->clks;
                clks[0].id = "ref";     /* digital (& analog) clock */
                clks[1].id = "da_ref";  /* analog clock */
                retval = devm_clk_bulk_get_optional(subdev, TPHY_CLKS_CNT, clks);
                if (retval)
                        return retval;

                retval = phy_type_syscon_get(instance, child_np);
                if (retval)
                        return retval;
        }

        provider = devm_of_phy_provider_register(dev, mtk_phy_xlate);

        return PTR_ERR_OR_ZERO(provider);
}

static struct platform_driver mtk_tphy_driver = {
        .probe          = mtk_tphy_probe,
        .driver         = {
                .name   = "mtk-tphy",
                .of_match_table = mtk_tphy_id_table,
        },
};

module_platform_driver(mtk_tphy_driver);

MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
MODULE_DESCRIPTION("MediaTek T-PHY driver");
MODULE_LICENSE("GPL v2");