src/main/target/stm32f7xx_hal_conf.h

   1 /**
   2   ******************************************************************************
   3   * @file    stm32f7xx_hal_conf.h
   4   * @brief   HAL configuration file.
   5   ******************************************************************************
   6   * @attention
   7   *
   8   * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
   9   *
  10   * Redistribution and use in source and binary forms, with or without modification,
  11   * are permitted provided that the following conditions are met:
  12   *   1. Redistributions of source code must retain the above copyright notice,
  13   *      this list of conditions and the following disclaimer.
  14   *   2. Redistributions in binary form must reproduce the above copyright notice,
  15   *      this list of conditions and the following disclaimer in the documentation
  16   *      and/or other materials provided with the distribution.
  17   *   3. Neither the name of STMicroelectronics nor the names of its contributors
  18   *      may be used to endorse or promote products derived from this software
  19   *      without specific prior written permission.
  20   *
  21   * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  22   * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  23   * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  24   * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
  25   * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  26   * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  27   * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
  28   * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  29   * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  30   * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  31   *
  32   ******************************************************************************
  33   */
  34
  35 /* Define to prevent recursive inclusion -------------------------------------*/
  36 #ifndef __STM32F7xx_HAL_CONF_H
  37 #define __STM32F7xx_HAL_CONF_H
  38
  39 #ifdef __cplusplus
  40  extern "C" {
  41 #endif
  42
  43 /* Exported types ------------------------------------------------------------*/
  44 /* Exported constants --------------------------------------------------------*/
  45
  46 /* ########################## Module Selection ############################## */
  47 /**
  48   * @brief This is the list of modules to be used in the HAL driver
  49   */
  50 #define HAL_MODULE_ENABLED
  51
  52 #define HAL_ADC_MODULE_ENABLED
  53 /* #define HAL_CAN_MODULE_ENABLED   */
  54 /* #define HAL_CEC_MODULE_ENABLED   */
  55 /* #define HAL_CRC_MODULE_ENABLED   */
  56 /* #define HAL_CRYP_MODULE_ENABLED   */
  57 /* #define HAL_DAC_MODULE_ENABLED   */
  58 /* #define HAL_DCMI_MODULE_ENABLED   */
  59 /* #define HAL_DMA2D_MODULE_ENABLED   */
  60 /* #define HAL_ETH_MODULE_ENABLED   */
  61 /* #define HAL_NAND_MODULE_ENABLED   */
  62 /* #define HAL_NOR_MODULE_ENABLED   */
  63 /* #define HAL_SRAM_MODULE_ENABLED   */
  64 /* #define HAL_SDRAM_MODULE_ENABLED   */
  65 /* #define HAL_HASH_MODULE_ENABLED   */
  66 /* #define HAL_I2S_MODULE_ENABLED   */
  67 /* #define HAL_IWDG_MODULE_ENABLED   */
  68 /* #define HAL_LPTIM_MODULE_ENABLED   */
  69 /* #define HAL_LTDC_MODULE_ENABLED   */
  70 /* #define HAL_QSPI_MODULE_ENABLED   */
  71 /* #define HAL_RNG_MODULE_ENABLED   */
  72 /* #define HAL_RTC_MODULE_ENABLED   */
  73 /* #define HAL_SAI_MODULE_ENABLED   */
  74 /* #define HAL_SD_MODULE_ENABLED   */
  75 /* #define HAL_MMC_MODULE_ENABLED   */
  76 /* #define HAL_SPDIFRX_MODULE_ENABLED   */
  77 #define HAL_SPI_MODULE_ENABLED
  78 #define HAL_TIM_MODULE_ENABLED
  79 #define HAL_UART_MODULE_ENABLED
  80 #define HAL_USART_MODULE_ENABLED
  81 /* #define HAL_IRDA_MODULE_ENABLED   */
  82 /* #define HAL_SMARTCARD_MODULE_ENABLED   */
  83 /* #define HAL_WWDG_MODULE_ENABLED   */
  84 #define HAL_PCD_MODULE_ENABLED
  85 /* #define HAL_HCD_MODULE_ENABLED   */
  86 /* #define HAL_DFSDM_MODULE_ENABLED   */
  87 /* #define HAL_DSI_MODULE_ENABLED   */
  88 /* #define HAL_JPEG_MODULE_ENABLED   */
  89 /* #define HAL_MDIOS_MODULE_ENABLED   */
  90 /* #define HAL_SMBUS_MODULE_ENABLED   */
  91 /* #define HAL_MMC_MODULE_ENABLED   */
  92 #define HAL_GPIO_MODULE_ENABLED
  93 #define HAL_DMA_MODULE_ENABLED
  94 #define HAL_RCC_MODULE_ENABLED
  95 #define HAL_FLASH_MODULE_ENABLED
  96 #define HAL_PWR_MODULE_ENABLED
  97 #define HAL_I2C_MODULE_ENABLED
  98 #define HAL_CORTEX_MODULE_ENABLED
  99
 100 /* ########################## HSE/HSI Values adaptation ##################### */
 101 /**
 102   * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
 103   *        This value is used by the RCC HAL module to compute the system frequency
 104   *        (when HSE is used as system clock source, directly or through the PLL).
 105   */
 106 #if !defined  (HSE_VALUE)
 107   #define HSE_VALUE    ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
 108 #endif /* HSE_VALUE */
 109
 110 #if !defined  (HSE_STARTUP_TIMEOUT)
 111   #define HSE_STARTUP_TIMEOUT    ((uint32_t)100U)   /*!< Time out for HSE start up, in ms */
 112 #endif /* HSE_STARTUP_TIMEOUT */
 113
 114 /**
 115   * @brief Internal High Speed oscillator (HSI) value.
 116   *        This value is used by the RCC HAL module to compute the system frequency
 117   *        (when HSI is used as system clock source, directly or through the PLL).
 118   */
 119 #if !defined  (HSI_VALUE)
 120   #define HSI_VALUE    ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
 121 #endif /* HSI_VALUE */
 122
 123 /**
 124   * @brief Internal Low Speed oscillator (LSI) value.
 125   */
 126 #if !defined  (LSI_VALUE)
 127  #define LSI_VALUE  ((uint32_t)32000U)       /*!< LSI Typical Value in Hz*/
 128 #endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
 129                                              The real value may vary depending on the variations
 130                                              in voltage and temperature.  */
 131 /**
 132   * @brief External Low Speed oscillator (LSE) value.
 133   */
 134 #if !defined  (LSE_VALUE)
 135  #define LSE_VALUE  ((uint32_t)32768U)    /*!< Value of the External Low Speed oscillator in Hz */
 136 #endif /* LSE_VALUE */
 137
 138 #if !defined  (LSE_STARTUP_TIMEOUT)
 139   #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000U)   /*!< Time out for LSE start up, in ms */
 140 #endif /* LSE_STARTUP_TIMEOUT */
 141
 142 /**
 143   * @brief External clock source for I2S peripheral
 144   *        This value is used by the I2S HAL module to compute the I2S clock source
 145   *        frequency, this source is inserted directly through I2S_CKIN pad.
 146   */
 147 #if !defined  (EXTERNAL_CLOCK_VALUE)
 148   #define EXTERNAL_CLOCK_VALUE    ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
 149 #endif /* EXTERNAL_CLOCK_VALUE */
 150
 151 /* Tip: To avoid modifying this file each time you need to use different HSE,
 152    ===  you can define the HSE value in your toolchain compiler preprocessor. */
 153
 154 /* ########################### System Configuration ######################### */
 155 /**
 156   * @brief This is the HAL system configuration section
 157   */
 158 #define  VDD_VALUE                    ((uint32_t)3300U) /*!< Value of VDD in mv */
 159 #define  TICK_INT_PRIORITY            ((uint32_t)0U) /*!< tick interrupt priority */
 160 #define  USE_RTOS                     0U
 161 #define  PREFETCH_ENABLE              0U
 162 #define  ART_ACCLERATOR_ENABLE        0U /* To enable instruction cache and prefetch */
 163
 164 /* ########################## Assert Selection ############################## */
 165 /**
 166   * @brief Uncomment the line below to expanse the "assert_param" macro in the
 167   *        HAL drivers code
 168   */
 169 /* #define USE_FULL_ASSERT    1 */
 170
 171 /* ################## Ethernet peripheral configuration ##################### */
 172
 173 /* Section 1 : Ethernet peripheral configuration */
 174
 175 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
 176 #define MAC_ADDR0   2U
 177 #define MAC_ADDR1   0U
 178 #define MAC_ADDR2   0U
 179 #define MAC_ADDR3   0U
 180 #define MAC_ADDR4   0U
 181 #define MAC_ADDR5   0U
 182
 183 /* Definition of the Ethernet driver buffers size and count */
 184 #define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
 185 #define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
 186 #define ETH_RXBUFNB                    ((uint32_t)4U)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
 187 #define ETH_TXBUFNB                    ((uint32_t)4U)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
 188
 189 /* Section 2: PHY configuration section */
 190
 191 /* DP83848_PHY_ADDRESS Address*/
 192 #define DP83848_PHY_ADDRESS           0x01U
 193 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
 194 #define PHY_RESET_DELAY                 ((uint32_t)0x000000FFU)
 195 /* PHY Configuration delay */
 196 #define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFFU)
 197
 198 #define PHY_READ_TO                     ((uint32_t)0x0000FFFFU)
 199 #define PHY_WRITE_TO                    ((uint32_t)0x0000FFFFU)
 200
 201 /* Section 3: Common PHY Registers */
 202
 203 #define PHY_BCR                         ((uint16_t)0x0000U)    /*!< Transceiver Basic Control Register   */
 204 #define PHY_BSR                         ((uint16_t)0x0001U)    /*!< Transceiver Basic Status Register    */
 205
 206 #define PHY_RESET                       ((uint16_t)0x8000U)  /*!< PHY Reset */
 207 #define PHY_LOOPBACK                    ((uint16_t)0x4000U)  /*!< Select loop-back mode */
 208 #define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100U)  /*!< Set the full-duplex mode at 100 Mb/s */
 209 #define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000U)  /*!< Set the half-duplex mode at 100 Mb/s */
 210 #define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100U)  /*!< Set the full-duplex mode at 10 Mb/s  */
 211 #define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000U)  /*!< Set the half-duplex mode at 10 Mb/s  */
 212 #define PHY_AUTONEGOTIATION             ((uint16_t)0x1000U)  /*!< Enable auto-negotiation function     */
 213 #define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200U)  /*!< Restart auto-negotiation function    */
 214 #define PHY_POWERDOWN                   ((uint16_t)0x0800U)  /*!< Select the power down mode           */
 215 #define PHY_ISOLATE                     ((uint16_t)0x0400U)  /*!< Isolate PHY from MII                 */
 216
 217 #define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020U)  /*!< Auto-Negotiation process completed   */
 218 #define PHY_LINKED_STATUS               ((uint16_t)0x0004U)  /*!< Valid link established               */
 219 #define PHY_JABBER_DETECTION            ((uint16_t)0x0002U)  /*!< Jabber condition detected            */
 220
 221 /* Section 4: Extended PHY Registers */
 222 #define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
 223
 224 #define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
 225 #define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
 226
 227 /* ################## SPI peripheral configuration ########################## */
 228
 229 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
 230 * Activated: CRC code is present inside driver
 231 * Deactivated: CRC code cleaned from driver
 232 */
 233
 234 #define USE_SPI_CRC                     0U
 235
 236 /* Includes ------------------------------------------------------------------*/
 237 /**
 238   * @brief Include module's header file
 239   */
 240
 241 #ifdef HAL_RCC_MODULE_ENABLED
 242   #include "stm32f7xx_hal_rcc.h"
 243 #endif /* HAL_RCC_MODULE_ENABLED */
 244
 245 #ifdef HAL_GPIO_MODULE_ENABLED
 246   #include "stm32f7xx_hal_gpio.h"
 247 #endif /* HAL_GPIO_MODULE_ENABLED */
 248
 249 #ifdef HAL_DMA_MODULE_ENABLED
 250   #include "stm32f7xx_hal_dma.h"
 251 #endif /* HAL_DMA_MODULE_ENABLED */
 252
 253 #ifdef HAL_CORTEX_MODULE_ENABLED
 254   #include "stm32f7xx_hal_cortex.h"
 255 #endif /* HAL_CORTEX_MODULE_ENABLED */
 256
 257 #ifdef HAL_ADC_MODULE_ENABLED
 258   #include "stm32f7xx_hal_adc.h"
 259 #endif /* HAL_ADC_MODULE_ENABLED */
 260
 261 #ifdef HAL_CAN_MODULE_ENABLED
 262   #include "stm32f7xx_hal_can.h"
 263 #endif /* HAL_CAN_MODULE_ENABLED */
 264
 265 #ifdef HAL_CEC_MODULE_ENABLED
 266   #include "stm32f7xx_hal_cec.h"
 267 #endif /* HAL_CEC_MODULE_ENABLED */
 268
 269 #ifdef HAL_CRC_MODULE_ENABLED
 270   #include "stm32f7xx_hal_crc.h"
 271 #endif /* HAL_CRC_MODULE_ENABLED */
 272
 273 #ifdef HAL_CRYP_MODULE_ENABLED
 274   #include "stm32f7xx_hal_cryp.h"
 275 #endif /* HAL_CRYP_MODULE_ENABLED */
 276
 277 #ifdef HAL_DMA2D_MODULE_ENABLED
 278   #include "stm32f7xx_hal_dma2d.h"
 279 #endif /* HAL_DMA2D_MODULE_ENABLED */
 280
 281 #ifdef HAL_DAC_MODULE_ENABLED
 282   #include "stm32f7xx_hal_dac.h"
 283 #endif /* HAL_DAC_MODULE_ENABLED */
 284
 285 #ifdef HAL_DCMI_MODULE_ENABLED
 286   #include "stm32f7xx_hal_dcmi.h"
 287 #endif /* HAL_DCMI_MODULE_ENABLED */
 288
 289 #ifdef HAL_ETH_MODULE_ENABLED
 290   #include "stm32f7xx_hal_eth.h"
 291 #endif /* HAL_ETH_MODULE_ENABLED */
 292
 293 #ifdef HAL_FLASH_MODULE_ENABLED
 294   #include "stm32f7xx_hal_flash.h"
 295 #endif /* HAL_FLASH_MODULE_ENABLED */
 296
 297 #ifdef HAL_SRAM_MODULE_ENABLED
 298   #include "stm32f7xx_hal_sram.h"
 299 #endif /* HAL_SRAM_MODULE_ENABLED */
 300
 301 #ifdef HAL_NOR_MODULE_ENABLED
 302   #include "stm32f7xx_hal_nor.h"
 303 #endif /* HAL_NOR_MODULE_ENABLED */
 304
 305 #ifdef HAL_NAND_MODULE_ENABLED
 306   #include "stm32f7xx_hal_nand.h"
 307 #endif /* HAL_NAND_MODULE_ENABLED */
 308
 309 #ifdef HAL_SDRAM_MODULE_ENABLED
 310   #include "stm32f7xx_hal_sdram.h"
 311 #endif /* HAL_SDRAM_MODULE_ENABLED */
 312
 313 #ifdef HAL_HASH_MODULE_ENABLED
 314  #include "stm32f7xx_hal_hash.h"
 315 #endif /* HAL_HASH_MODULE_ENABLED */
 316
 317 #ifdef HAL_I2C_MODULE_ENABLED
 318  #include "stm32f7xx_hal_i2c.h"
 319 #endif /* HAL_I2C_MODULE_ENABLED */
 320
 321 #ifdef HAL_I2S_MODULE_ENABLED
 322  #include "stm32f7xx_hal_i2s.h"
 323 #endif /* HAL_I2S_MODULE_ENABLED */
 324
 325 #ifdef HAL_IWDG_MODULE_ENABLED
 326  #include "stm32f7xx_hal_iwdg.h"
 327 #endif /* HAL_IWDG_MODULE_ENABLED */
 328
 329 #ifdef HAL_LPTIM_MODULE_ENABLED
 330  #include "stm32f7xx_hal_lptim.h"
 331 #endif /* HAL_LPTIM_MODULE_ENABLED */
 332
 333 #ifdef HAL_LTDC_MODULE_ENABLED
 334  #include "stm32f7xx_hal_ltdc.h"
 335 #endif /* HAL_LTDC_MODULE_ENABLED */
 336
 337 #ifdef HAL_PWR_MODULE_ENABLED
 338  #include "stm32f7xx_hal_pwr.h"
 339 #endif /* HAL_PWR_MODULE_ENABLED */
 340
 341 #ifdef HAL_QSPI_MODULE_ENABLED
 342  #include "stm32f7xx_hal_qspi.h"
 343 #endif /* HAL_QSPI_MODULE_ENABLED */
 344
 345 #ifdef HAL_RNG_MODULE_ENABLED
 346  #include "stm32f7xx_hal_rng.h"
 347 #endif /* HAL_RNG_MODULE_ENABLED */
 348
 349 #ifdef HAL_RTC_MODULE_ENABLED
 350  #include "stm32f7xx_hal_rtc.h"
 351 #endif /* HAL_RTC_MODULE_ENABLED */
 352
 353 #ifdef HAL_SAI_MODULE_ENABLED
 354  #include "stm32f7xx_hal_sai.h"
 355 #endif /* HAL_SAI_MODULE_ENABLED */
 356
 357 #ifdef HAL_SD_MODULE_ENABLED
 358  #include "stm32f7xx_hal_sd.h"
 359 #endif /* HAL_SD_MODULE_ENABLED */
 360
 361 #ifdef HAL_MMC_MODULE_ENABLED
 362  #include "stm32f7xx_hal_mmc.h"
 363 #endif /* HAL_MMC_MODULE_ENABLED */
 364
 365 #ifdef HAL_SPDIFRX_MODULE_ENABLED
 366  #include "stm32f7xx_hal_spdifrx.h"
 367 #endif /* HAL_SPDIFRX_MODULE_ENABLED */
 368
 369 #ifdef HAL_SPI_MODULE_ENABLED
 370  #include "stm32f7xx_hal_spi.h"
 371 #endif /* HAL_SPI_MODULE_ENABLED */
 372
 373 #ifdef HAL_TIM_MODULE_ENABLED
 374  #include "stm32f7xx_hal_tim.h"
 375 #endif /* HAL_TIM_MODULE_ENABLED */
 376
 377 #ifdef HAL_UART_MODULE_ENABLED
 378  #include "stm32f7xx_hal_uart.h"
 379 #endif /* HAL_UART_MODULE_ENABLED */
 380
 381 #ifdef HAL_USART_MODULE_ENABLED
 382  #include "stm32f7xx_hal_usart.h"
 383 #endif /* HAL_USART_MODULE_ENABLED */
 384
 385 #ifdef HAL_IRDA_MODULE_ENABLED
 386  #include "stm32f7xx_hal_irda.h"
 387 #endif /* HAL_IRDA_MODULE_ENABLED */
 388
 389 #ifdef HAL_SMARTCARD_MODULE_ENABLED
 390  #include "stm32f7xx_hal_smartcard.h"
 391 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
 392
 393 #ifdef HAL_WWDG_MODULE_ENABLED
 394  #include "stm32f7xx_hal_wwdg.h"
 395 #endif /* HAL_WWDG_MODULE_ENABLED */
 396
 397 #ifdef HAL_PCD_MODULE_ENABLED
 398  #include "stm32f7xx_hal_pcd.h"
 399 #endif /* HAL_PCD_MODULE_ENABLED */
 400
 401 #ifdef HAL_HCD_MODULE_ENABLED
 402  #include "stm32f7xx_hal_hcd.h"
 403 #endif /* HAL_HCD_MODULE_ENABLED */
 404
 405 #ifdef HAL_DFSDM_MODULE_ENABLED
 406  #include "stm32f7xx_hal_dfsdm.h"
 407 #endif /* HAL_DFSDM_MODULE_ENABLED */
 408
 409 #ifdef HAL_DSI_MODULE_ENABLED
 410  #include "stm32f7xx_hal_dsi.h"
 411 #endif /* HAL_DSI_MODULE_ENABLED */
 412
 413 #ifdef HAL_JPEG_MODULE_ENABLED
 414  #include "stm32f7xx_hal_jpeg.h"
 415 #endif /* HAL_JPEG_MODULE_ENABLED */
 416
 417 #ifdef HAL_MDIOS_MODULE_ENABLED
 418  #include "stm32f7xx_hal_mdios.h"
 419 #endif /* HAL_MDIOS_MODULE_ENABLED */
 420
 421 #ifdef HAL_SMBUS_MODULE_ENABLED
 422  #include "stm32f7xx_hal_smbus.h"
 423 #endif /* HAL_SMBUS_MODULE_ENABLED */
 424
 425 #ifdef HAL_MMC_MODULE_ENABLED
 426  #include "stm32f7xx_hal_mmc.h"
 427 #endif /* HAL_MMC_MODULE_ENABLED */
 428
 429 /* Exported macro ------------------------------------------------------------*/
 430 #ifdef  USE_FULL_ASSERT
 431 /**
 432   * @brief  The assert_param macro is used for function's parameters check.
 433   * @param  expr: If expr is false, it calls assert_failed function
 434   *         which reports the name of the source file and the source
 435   *         line number of the call that failed.
 436   *         If expr is true, it returns no value.
 437   * @retval None
 438   */
 439   #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
 440 /* Exported functions ------------------------------------------------------- */
 441   void assert_failed(uint8_t* file, uint32_t line);
 442 #else
 443   #define assert_param(expr) ((void)0U)
 444 #endif /* USE_FULL_ASSERT */
 445
 446 #ifdef __cplusplus
 447 }
 448 #endif
 449
 450 #endif /* __STM32F7xx_HAL_CONF_H */
 451
 452
 453 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/