Legacy-target-SPRacingF3EVO_1SS.md

   1 # Board - Seriously Pro SP Racing F3 EVO
   2
   3 The Seriously Pro Racing F3 Evo board (SPRacingF3EVO) is the evolution of the first board designed specifically for Cleanflight.
   4
   5 Purchasing boards directly from SeriouslyPro / SP Racing and official retailers helps fund Cleanflight development, it's the reason the Seriously Pro boards exist!  Official retailers are always listed on the SeriouslyPro.com website.
   6
   7 Full details available on the website, here:
   8
   9 http://seriouslypro.com/spracingf3evo
  10
  11 ## Hardware Features
  12
  13 * Next-generation STM32 F3 processor with hardware floating point unit for efficient flight calculations and faster ARM-Cortex M4 core.
  14 * MicroSD-Card socket for black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.
  15 * Race transponder built in - just turn up at a race and have your lap times recorded.
  16 * Features the latest Accelerometer, Gyro and Mag/Compass and Baro/Altitude sensor technology.
  17 * Wire up using using pin headers for all major connections for excellent crash-durability.  Use either right-angled or straight pin-headers.
  18 * No compromise I/O. Use all the features all the time; e.g. Connect your USB + OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + 8 motors - all at the same time!
  19 * 8 PWM output lines for ESCs and Servos. Arranged for easy wiring on standard pin headers.
  20 * Supports direct connection of SBus, SumH, SumD, Spektrum1024/2048, XBus receivers. No external inverters required (built-in).
  21 * Supports direct connection of 3.3v Spektrum Satellite receivers via 3 pin through-hole JST-ZH connector.
  22 * Dedicated PPM receiver input.
  23 * 3 Serial Ports - NOT shared with the USB socket.
  24 * Telemetry port
  25 * Micro USB socket.
  26 * Dedicated output for programmable LEDs - great for orientation, racing and night flying. (Currently mutually exclusive with the Transponder).
  27 * Dedicated I2C port for connection of OLED display without needing flight battery.
  28 * Battery monitoring for voltage and current.
  29 * RSSI monitoring (analogue or PWM).
  30 * Buzzer port for audible warnings and notifications.
  31 * Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.
  32 * Symmetrical design for a super tidy wiring.
  33 * JST-SH sockets only for I2C, UART2 and SWD.  UART2 also on through-hole pins.
  34 * Flashing via USB or serial port.
  35 * Stackable design - perfect for integrating with OSDs and power distribution boards.
  36 * Standard mounting - 36x36mm with standard 30.5mm mounting holes.
  37 * LEDs for 3v, 5v and Status for easy diagnostics.
  38 * Copper-etched Cleanflight logo.
  39
  40 ## Serial Ports
  41
  42 | Value | Identifier   | RX           | TX           | 5v Tolerant | Notes                                                                                       |
  43 | ----- | ------------ | ------------ | ------------ | ----------- | ------------------------------------------------------------------------------------------- |
  44 | 1     | USART1       | PA10         | PA9          | YES         | 2 through-hole pins. Use for connecting to OSD/GPS/BlueTooth. |
  45 | 2     | USART2       | PA15         | PA14 / SWCLK | YES         | JST socket and PPM header. Use to connect to RX. |
  46 | 3     | USART3       | PB11 / AF7   | PB10 / AF7   | NO          | Available on 4 through-hole pins. 3.3V signals only ! Use for GPS, Spektrum Satellite RX, SmartPort Telemetry, HoTT telemetry, etc. |
  47
  48 * You cannot use SWD and USART2 at the same time.
  49 * When using a Serial RX receiver the TXD (T2) pin cannot be used for telemetry. Use UART3 TXD instead.
  50 * One Software serial is supported in th SPRacingF3EVO_1SS version, see table below
  51 * Windows DFU Flashing requires Zadig (see configurator)
  52
  53 ### SoftSerial
  54
  55 | Pin | Function       | Notes                            |
  56 | --- | -------------- | -------------------------------- |
  57 | 7   | SOFTSERIAL1 RX | SoftSerial disables Servo 5,6    |
  58 | 8   | SOFTSERIAL1 TX |                                  |
  59
  60 ## Pinouts
  61
  62 Full pinout details are available in the manual, here:
  63
  64 http://seriouslypro.com/files/SPRacingF3EVO-Manual-latest.pdf
  65
  66 ### IO_1
  67
  68 The 6 pin IO_1 connector has the following pinouts when used in RX_SERIAL mode.
  69
  70 | Pin | Function       | Notes                                        |
  71 | --- | -------------- | -------------------------------------------- |
  72 | 1   | Ground         |                                              |
  73 | 2   | VCC_IN         | Voltage as-supplied by BEC.                  |
  74 | 3   | RX_SERIAL      | Enable `feature RX_SERIAL` |
  75 | 4   | | |
  76 | 5   | +V BATTERY     | Voltage as-supplied by Battery.              |
  77 | 6   | -V BATTERY     | Voltage as-supplied by Battery.              |
  78
  79 When RX_PPM is used the IO_1 pinout is as follows.
  80
  81 | Pin | Function       | Notes                                        |
  82 | --- | -------------- | -------------------------------------------- |
  83 | 1   | Ground         |                                              |
  84 | 2   | VCC_IN         | Voltage as-supplied by BEC.                  |
  85 | 3   | RX_PPM         | Enable `feature RX_PPM`                      |
  86 | 4   | TELEMETRY      | Enable `feature TELEMETRY`                   |
  87 | 5   | +V BATTERY     | Voltage as-supplied by Battery.              |
  88 | 6   | -V BATTERY     | Voltage as-supplied by Battery.              |
  89
  90 ### IO_2
  91
  92 When TRANSPONDER is used and the IR solder pads are shorted, the 6 pin IO_2 pinout is as follows.
  93
  94 | Pin | Function                  | Notes                                        |
  95 | --- | ------------------------- | -------------------------------------------- |
  96 | 1   | IR-                       | Short leg of the IR LED                      |
  97 | 2   | IR+                       | Long leg of the IR LED                       |
  98 | 3   | CURRENT                   | Current Sensor                               |
  99 | 4   | RSSI                      | RSSI (PWM or Analog - select by solder pads) |
 100 | 5   | BUZZER+                   | 5V Source                                    |
 101 | 6   | BUZZER-                   | Buzzer signal                                |
 102
 103 When LEDSTRIP is used and the LED solder pads are shorted, the 6 pin IO_2 pinout is as follows.
 104
 105 | Pin | Function                  | Notes                                        |
 106 | --- | ------------------------- | -------------------------------------------- |
 107 | 1   | | |
 108 | 2   | LEDSTRIP                  | WS2812 Ledstrip data                         |
 109 | 3   | CURRENT                   | Current Sensor                               |
 110 | 4   | RSSI                      | RSSI (PWM or Analog - select by solder pads) |
 111 | 5   | BUZZER+                   | 5V Source                                    |
 112 | 6   | BUZZER-                   | Buzzer signal                                |
 113
 114 ### UART1
 115
 116 | Pin | Function       | Notes                                        |
 117 | --- | -------------- | -------------------------------------------- |
 118 | 3   | TXD            |                                              |
 119 | 4   | RXD            |                                              |
 120
 121 ### UART2/3
 122
 123 | Pin | Function       | Notes                                        |
 124 | --- | -------------- | -------------------------------------------- |
 125 | 1   | Ground         |                                              |
 126 | 2   | VCC_IN         | Voltage as-supplied by BEC.                  |
 127 | 3   | TXD            |                                              |
 128 | 4   | RXD            |                                              |
 129
 130 ### Spektrum Satellite
 131
 132 | Pin | Function       | Notes                                        |
 133 | --- | -------------- | -------------------------------------------- |
 134 | 3   | 3.3V           |                                              |
 135 | 2   | Ground         |                                              |
 136 | 1   | RXD            |                                              |
 137
 138 ### I2C
 139
 140 | Pin | Function       | Notes                                        |
 141 | --- | -------------- | -------------------------------------------- |
 142 | 1   | Ground         |                                              |
 143 | 2   | 5.0v           | Voltage as-supplied by BEC OR USB, always on |
 144 | 3   | SCL            | 3.3V signals only                            |
 145 | 4   | SDA            | 3.3V signals only                            |
 146
 147 ### SWD
 148
 149 The port cannot be used at the same time as UART2.
 150
 151 | Pin | Function       | Notes                                        |
 152 | --- | -------------- | -------------------------------------------- |
 153 | 1   | Ground         |                                              |
 154 | 2   | NRST           |                                              |
 155 | 3   | SWDIO          |                                              |
 156 | 4   | SWDCLK         |                                              |
 157
 158
 159