Added !vmlinux.lds.h to .gitignore because it would otherwise be ignored.

[jz_linux_2.6.24.3.git] / drivers / net / ixgb / ixgb_hw.c

/*******************************************************************************

  Intel PRO/10GbE Linux driver
  Copyright(c) 1999 - 2006 Intel Corporation.

  This program is free software; you can redistribute it and/or modify it
  under the terms and conditions of the GNU General Public License,
  version 2, as published by the Free Software Foundation.

  This program is distributed in the hope it will be useful, but WITHOUT
  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  more details.

  You should have received a copy of the GNU General Public License along with
  this program; if not, write to the Free Software Foundation, Inc.,
  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.

  The full GNU General Public License is included in this distribution in
  the file called "COPYING".

  Contact Information:
  Linux NICS <linux.nics@intel.com>
  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497

*******************************************************************************/

/* ixgb_hw.c
 * Shared functions for accessing and configuring the adapter
 */

#include "ixgb_hw.h"
#include "ixgb_ids.h"

/*  Local function prototypes */

static uint32_t ixgb_hash_mc_addr(struct ixgb_hw *hw, uint8_t * mc_addr);

static void ixgb_mta_set(struct ixgb_hw *hw, uint32_t hash_value);

static void ixgb_get_bus_info(struct ixgb_hw *hw);

static boolean_t ixgb_link_reset(struct ixgb_hw *hw);

static void ixgb_optics_reset(struct ixgb_hw *hw);

static ixgb_phy_type ixgb_identify_phy(struct ixgb_hw *hw);

static void ixgb_clear_hw_cntrs(struct ixgb_hw *hw);

static void ixgb_clear_vfta(struct ixgb_hw *hw);

static void ixgb_init_rx_addrs(struct ixgb_hw *hw);

static uint16_t ixgb_read_phy_reg(struct ixgb_hw *hw,
                                  uint32_t reg_address,
                                  uint32_t phy_address,
                                  uint32_t device_type);

static boolean_t ixgb_setup_fc(struct ixgb_hw *hw);

static boolean_t mac_addr_valid(uint8_t *mac_addr);

static uint32_t ixgb_mac_reset(struct ixgb_hw *hw)
{
        uint32_t ctrl_reg;

        ctrl_reg =  IXGB_CTRL0_RST |
                                IXGB_CTRL0_SDP3_DIR |   /* All pins are Output=1 */
                                IXGB_CTRL0_SDP2_DIR |
                                IXGB_CTRL0_SDP1_DIR |
                                IXGB_CTRL0_SDP0_DIR |
                                IXGB_CTRL0_SDP3  |   /* Initial value 1101   */
                                IXGB_CTRL0_SDP2  |
                                IXGB_CTRL0_SDP0;

#ifdef HP_ZX1
        /* Workaround for 82597EX reset errata */
        IXGB_WRITE_REG_IO(hw, CTRL0, ctrl_reg);
#else
        IXGB_WRITE_REG(hw, CTRL0, ctrl_reg);
#endif

        /* Delay a few ms just to allow the reset to complete */
        msleep(IXGB_DELAY_AFTER_RESET);
        ctrl_reg = IXGB_READ_REG(hw, CTRL0);
#ifdef DBG
        /* Make sure the self-clearing global reset bit did self clear */
        ASSERT(!(ctrl_reg & IXGB_CTRL0_RST));
#endif

        if (hw->phy_type == ixgb_phy_type_txn17401) {
                ixgb_optics_reset(hw);
        }

        return ctrl_reg;
}

/******************************************************************************
 * Reset the transmit and receive units; mask and clear all interrupts.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
boolean_t
ixgb_adapter_stop(struct ixgb_hw *hw)
{
        uint32_t ctrl_reg;
        uint32_t icr_reg;

        DEBUGFUNC("ixgb_adapter_stop");

        /* If we are stopped or resetting exit gracefully and wait to be
         * started again before accessing the hardware.
         */
        if(hw->adapter_stopped) {
                DEBUGOUT("Exiting because the adapter is already stopped!!!\n");
                return FALSE;
        }

        /* Set the Adapter Stopped flag so other driver functions stop
         * touching the Hardware.
         */
        hw->adapter_stopped = TRUE;

        /* Clear interrupt mask to stop board from generating interrupts */
        DEBUGOUT("Masking off all interrupts\n");
        IXGB_WRITE_REG(hw, IMC, 0xFFFFFFFF);

        /* Disable the Transmit and Receive units.  Then delay to allow
         * any pending transactions to complete before we hit the MAC with
         * the global reset.
         */
        IXGB_WRITE_REG(hw, RCTL, IXGB_READ_REG(hw, RCTL) & ~IXGB_RCTL_RXEN);
        IXGB_WRITE_REG(hw, TCTL, IXGB_READ_REG(hw, TCTL) & ~IXGB_TCTL_TXEN);
        msleep(IXGB_DELAY_BEFORE_RESET);

        /* Issue a global reset to the MAC.  This will reset the chip's
         * transmit, receive, DMA, and link units.  It will not effect
         * the current PCI configuration.  The global reset bit is self-
         * clearing, and should clear within a microsecond.
         */
        DEBUGOUT("Issuing a global reset to MAC\n");

        ctrl_reg = ixgb_mac_reset(hw);

        /* Clear interrupt mask to stop board from generating interrupts */
        DEBUGOUT("Masking off all interrupts\n");
        IXGB_WRITE_REG(hw, IMC, 0xffffffff);

        /* Clear any pending interrupt events. */
        icr_reg = IXGB_READ_REG(hw, ICR);

        return (ctrl_reg & IXGB_CTRL0_RST);
}


/******************************************************************************
 * Identifies the vendor of the optics module on the adapter.  The SR adapters
 * support two different types of XPAK optics, so it is necessary to determine
 * which optics are present before applying any optics-specific workarounds.
 *
 * hw - Struct containing variables accessed by shared code.
 *
 * Returns: the vendor of the XPAK optics module.
 *****************************************************************************/
static ixgb_xpak_vendor
ixgb_identify_xpak_vendor(struct ixgb_hw *hw)
{
        uint32_t i;
        uint16_t vendor_name[5];
        ixgb_xpak_vendor xpak_vendor;

        DEBUGFUNC("ixgb_identify_xpak_vendor");

        /* Read the first few bytes of the vendor string from the XPAK NVR
         * registers.  These are standard XENPAK/XPAK registers, so all XPAK
         * devices should implement them. */
        for (i = 0; i < 5; i++) {
                vendor_name[i] = ixgb_read_phy_reg(hw,
                                                   MDIO_PMA_PMD_XPAK_VENDOR_NAME
                                                   + i, IXGB_PHY_ADDRESS,
                                                   MDIO_PMA_PMD_DID);
        }

        /* Determine the actual vendor */
        if (vendor_name[0] == 'I' &&
            vendor_name[1] == 'N' &&
            vendor_name[2] == 'T' &&
            vendor_name[3] == 'E' && vendor_name[4] == 'L') {
                xpak_vendor = ixgb_xpak_vendor_intel;
        } else {
                xpak_vendor = ixgb_xpak_vendor_infineon;
        }

        return (xpak_vendor);
}

/******************************************************************************
 * Determine the physical layer module on the adapter.
 *
 * hw - Struct containing variables accessed by shared code.  The device_id
 *      field must be (correctly) populated before calling this routine.
 *
 * Returns: the phy type of the adapter.
 *****************************************************************************/
static ixgb_phy_type
ixgb_identify_phy(struct ixgb_hw *hw)
{
        ixgb_phy_type phy_type;
        ixgb_xpak_vendor xpak_vendor;

        DEBUGFUNC("ixgb_identify_phy");

        /* Infer the transceiver/phy type from the device id */
        switch (hw->device_id) {
        case IXGB_DEVICE_ID_82597EX:
                DEBUGOUT("Identified TXN17401 optics\n");
                phy_type = ixgb_phy_type_txn17401;
                break;

        case IXGB_DEVICE_ID_82597EX_SR:
                /* The SR adapters carry two different types of XPAK optics
                 * modules; read the vendor identifier to determine the exact
                 * type of optics. */
                xpak_vendor = ixgb_identify_xpak_vendor(hw);
                if (xpak_vendor == ixgb_xpak_vendor_intel) {
                        DEBUGOUT("Identified TXN17201 optics\n");
                        phy_type = ixgb_phy_type_txn17201;
                } else {
                        DEBUGOUT("Identified G6005 optics\n");
                        phy_type = ixgb_phy_type_g6005;
                }
                break;
        case IXGB_DEVICE_ID_82597EX_LR:
                DEBUGOUT("Identified G6104 optics\n");
                phy_type = ixgb_phy_type_g6104;
                break;
        case IXGB_DEVICE_ID_82597EX_CX4:
                DEBUGOUT("Identified CX4\n");
                xpak_vendor = ixgb_identify_xpak_vendor(hw);
                if (xpak_vendor == ixgb_xpak_vendor_intel) {
                        DEBUGOUT("Identified TXN17201 optics\n");
                        phy_type = ixgb_phy_type_txn17201;
                } else {
                        DEBUGOUT("Identified G6005 optics\n");
                        phy_type = ixgb_phy_type_g6005;
                }
                break;
        default:
                DEBUGOUT("Unknown physical layer module\n");
                phy_type = ixgb_phy_type_unknown;
                break;
        }

        return (phy_type);
}

/******************************************************************************
 * Performs basic configuration of the adapter.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Resets the controller.
 * Reads and validates the EEPROM.
 * Initializes the receive address registers.
 * Initializes the multicast table.
 * Clears all on-chip counters.
 * Calls routine to setup flow control settings.
 * Leaves the transmit and receive units disabled and uninitialized.
 *
 * Returns:
 *      TRUE if successful,
 *      FALSE if unrecoverable problems were encountered.
 *****************************************************************************/
boolean_t
ixgb_init_hw(struct ixgb_hw *hw)
{
        uint32_t i;
        uint32_t ctrl_reg;
        boolean_t status;

        DEBUGFUNC("ixgb_init_hw");

        /* Issue a global reset to the MAC.  This will reset the chip's
         * transmit, receive, DMA, and link units.  It will not effect
         * the current PCI configuration.  The global reset bit is self-
         * clearing, and should clear within a microsecond.
         */
        DEBUGOUT("Issuing a global reset to MAC\n");

        ctrl_reg = ixgb_mac_reset(hw);

        DEBUGOUT("Issuing an EE reset to MAC\n");
#ifdef HP_ZX1
        /* Workaround for 82597EX reset errata */
        IXGB_WRITE_REG_IO(hw, CTRL1, IXGB_CTRL1_EE_RST);
#else
        IXGB_WRITE_REG(hw, CTRL1, IXGB_CTRL1_EE_RST);
#endif

        /* Delay a few ms just to allow the reset to complete */
        msleep(IXGB_DELAY_AFTER_EE_RESET);

        if (ixgb_get_eeprom_data(hw) == FALSE) {
                return(FALSE);
        }

        /* Use the device id to determine the type of phy/transceiver. */
        hw->device_id = ixgb_get_ee_device_id(hw);
        hw->phy_type = ixgb_identify_phy(hw);

        /* Setup the receive addresses.
         * Receive Address Registers (RARs 0 - 15).
         */
        ixgb_init_rx_addrs(hw);

        /*
         * Check that a valid MAC address has been set.
         * If it is not valid, we fail hardware init.
         */
        if (!mac_addr_valid(hw->curr_mac_addr)) {
                DEBUGOUT("MAC address invalid after ixgb_init_rx_addrs\n");
                return(FALSE);
        }

        /* tell the routines in this file they can access hardware again */
        hw->adapter_stopped = FALSE;

        /* Fill in the bus_info structure */
        ixgb_get_bus_info(hw);

        /* Zero out the Multicast HASH table */
        DEBUGOUT("Zeroing the MTA\n");
        for(i = 0; i < IXGB_MC_TBL_SIZE; i++)
                IXGB_WRITE_REG_ARRAY(hw, MTA, i, 0);

        /* Zero out the VLAN Filter Table Array */
        ixgb_clear_vfta(hw);

        /* Zero all of the hardware counters */
        ixgb_clear_hw_cntrs(hw);

        /* Call a subroutine to setup flow control. */
        status = ixgb_setup_fc(hw);

        /* 82597EX errata: Call check-for-link in case lane deskew is locked */
        ixgb_check_for_link(hw);

        return (status);
}

/******************************************************************************
 * Initializes receive address filters.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Places the MAC address in receive address register 0 and clears the rest
 * of the receive addresss registers. Clears the multicast table. Assumes
 * the receiver is in reset when the routine is called.
 *****************************************************************************/
static void
ixgb_init_rx_addrs(struct ixgb_hw *hw)
{
        uint32_t i;

        DEBUGFUNC("ixgb_init_rx_addrs");

        /*
         * If the current mac address is valid, assume it is a software override
         * to the permanent address.
         * Otherwise, use the permanent address from the eeprom.
         */
        if (!mac_addr_valid(hw->curr_mac_addr)) {

                /* Get the MAC address from the eeprom for later reference */
                ixgb_get_ee_mac_addr(hw, hw->curr_mac_addr);

                DEBUGOUT3(" Keeping Permanent MAC Addr =%.2X %.2X %.2X ",
                          hw->curr_mac_addr[0],
                          hw->curr_mac_addr[1], hw->curr_mac_addr[2]);
                DEBUGOUT3("%.2X %.2X %.2X\n",
                          hw->curr_mac_addr[3],
                          hw->curr_mac_addr[4], hw->curr_mac_addr[5]);
        } else {

                /* Setup the receive address. */
                DEBUGOUT("Overriding MAC Address in RAR[0]\n");
                DEBUGOUT3(" New MAC Addr =%.2X %.2X %.2X ",
                          hw->curr_mac_addr[0],
                          hw->curr_mac_addr[1], hw->curr_mac_addr[2]);
                DEBUGOUT3("%.2X %.2X %.2X\n",
                          hw->curr_mac_addr[3],
                          hw->curr_mac_addr[4], hw->curr_mac_addr[5]);

                ixgb_rar_set(hw, hw->curr_mac_addr, 0);
        }

        /* Zero out the other 15 receive addresses. */
        DEBUGOUT("Clearing RAR[1-15]\n");
        for(i = 1; i < IXGB_RAR_ENTRIES; i++) {
                /* Write high reg first to disable the AV bit first */
                IXGB_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
                IXGB_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
        }

        return;
}

/******************************************************************************
 * Updates the MAC's list of multicast addresses.
 *
 * hw - Struct containing variables accessed by shared code
 * mc_addr_list - the list of new multicast addresses
 * mc_addr_count - number of addresses
 * pad - number of bytes between addresses in the list
 *
 * The given list replaces any existing list. Clears the last 15 receive
 * address registers and the multicast table. Uses receive address registers
 * for the first 15 multicast addresses, and hashes the rest into the
 * multicast table.
 *****************************************************************************/
void
ixgb_mc_addr_list_update(struct ixgb_hw *hw,
                          uint8_t *mc_addr_list,
                          uint32_t mc_addr_count,
                          uint32_t pad)
{
        uint32_t hash_value;
        uint32_t i;
        uint32_t rar_used_count = 1;            /* RAR[0] is used for our MAC address */

        DEBUGFUNC("ixgb_mc_addr_list_update");

        /* Set the new number of MC addresses that we are being requested to use. */
        hw->num_mc_addrs = mc_addr_count;

        /* Clear RAR[1-15] */
        DEBUGOUT(" Clearing RAR[1-15]\n");
        for(i = rar_used_count; i < IXGB_RAR_ENTRIES; i++) {
                IXGB_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
                IXGB_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
        }

        /* Clear the MTA */
        DEBUGOUT(" Clearing MTA\n");
        for(i = 0; i < IXGB_MC_TBL_SIZE; i++) {
                IXGB_WRITE_REG_ARRAY(hw, MTA, i, 0);
        }

        /* Add the new addresses */
        for(i = 0; i < mc_addr_count; i++) {
                DEBUGOUT(" Adding the multicast addresses:\n");
                DEBUGOUT7(" MC Addr #%d =%.2X %.2X %.2X %.2X %.2X %.2X\n", i,
                          mc_addr_list[i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad)],
                          mc_addr_list[i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad) +
                                       1],
                          mc_addr_list[i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad) +
                                       2],
                          mc_addr_list[i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad) +
                                       3],
                          mc_addr_list[i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad) +
                                       4],
                          mc_addr_list[i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad) +
                                       5]);

                /* Place this multicast address in the RAR if there is room, *
                 * else put it in the MTA
                 */
                if(rar_used_count < IXGB_RAR_ENTRIES) {
                        ixgb_rar_set(hw,
                                     mc_addr_list +
                                     (i * (IXGB_ETH_LENGTH_OF_ADDRESS + pad)),
                                     rar_used_count);
                        DEBUGOUT1("Added a multicast address to RAR[%d]\n", i);
                        rar_used_count++;
                } else {
                        hash_value = ixgb_hash_mc_addr(hw,
                                                       mc_addr_list +
                                                       (i *
                                                        (IXGB_ETH_LENGTH_OF_ADDRESS
                                                         + pad)));

                        DEBUGOUT1(" Hash value = 0x%03X\n", hash_value);

                        ixgb_mta_set(hw, hash_value);
                }
        }

        DEBUGOUT("MC Update Complete\n");
        return;
}

/******************************************************************************
 * Hashes an address to determine its location in the multicast table
 *
 * hw - Struct containing variables accessed by shared code
 * mc_addr - the multicast address to hash
 *
 * Returns:
 *      The hash value
 *****************************************************************************/
static uint32_t
ixgb_hash_mc_addr(struct ixgb_hw *hw,
                   uint8_t *mc_addr)
{
        uint32_t hash_value = 0;

        DEBUGFUNC("ixgb_hash_mc_addr");

        /* The portion of the address that is used for the hash table is
         * determined by the mc_filter_type setting.
         */
        switch (hw->mc_filter_type) {
                /* [0] [1] [2] [3] [4] [5]
                 * 01  AA  00  12  34  56
                 * LSB                 MSB - According to H/W docs */
        case 0:
                /* [47:36] i.e. 0x563 for above example address */
                hash_value =
                    ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4));
                break;
        case 1:         /* [46:35] i.e. 0xAC6 for above example address */
                hash_value =
                    ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5));
                break;
        case 2:         /* [45:34] i.e. 0x5D8 for above example address */
                hash_value =
                    ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6));
                break;
        case 3:         /* [43:32] i.e. 0x634 for above example address */
                hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8));
                break;
        default:
                /* Invalid mc_filter_type, what should we do? */
                DEBUGOUT("MC filter type param set incorrectly\n");
                ASSERT(0);
                break;
        }

        hash_value &= 0xFFF;
        return (hash_value);
}

/******************************************************************************
 * Sets the bit in the multicast table corresponding to the hash value.
 *
 * hw - Struct containing variables accessed by shared code
 * hash_value - Multicast address hash value
 *****************************************************************************/
static void
ixgb_mta_set(struct ixgb_hw *hw,
                  uint32_t hash_value)
{
        uint32_t hash_bit, hash_reg;
        uint32_t mta_reg;

        /* The MTA is a register array of 128 32-bit registers.
         * It is treated like an array of 4096 bits.  We want to set
         * bit BitArray[hash_value]. So we figure out what register
         * the bit is in, read it, OR in the new bit, then write
         * back the new value.  The register is determined by the
         * upper 7 bits of the hash value and the bit within that
         * register are determined by the lower 5 bits of the value.
         */
        hash_reg = (hash_value >> 5) & 0x7F;
        hash_bit = hash_value & 0x1F;

        mta_reg = IXGB_READ_REG_ARRAY(hw, MTA, hash_reg);

        mta_reg |= (1 << hash_bit);

        IXGB_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta_reg);

        return;
}

/******************************************************************************
 * Puts an ethernet address into a receive address register.
 *
 * hw - Struct containing variables accessed by shared code
 * addr - Address to put into receive address register
 * index - Receive address register to write
 *****************************************************************************/
void
ixgb_rar_set(struct ixgb_hw *hw,
                  uint8_t *addr,
                  uint32_t index)
{
        uint32_t rar_low, rar_high;

        DEBUGFUNC("ixgb_rar_set");

        /* HW expects these in little endian so we reverse the byte order
         * from network order (big endian) to little endian
         */
        rar_low = ((uint32_t) addr[0] |
                   ((uint32_t)addr[1] << 8) |
                   ((uint32_t)addr[2] << 16) |
                   ((uint32_t)addr[3] << 24));

        rar_high = ((uint32_t) addr[4] |
                        ((uint32_t)addr[5] << 8) |
                        IXGB_RAH_AV);

        IXGB_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
        IXGB_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
        return;
}

/******************************************************************************
 * Writes a value to the specified offset in the VLAN filter table.
 *
 * hw - Struct containing variables accessed by shared code
 * offset - Offset in VLAN filer table to write
 * value - Value to write into VLAN filter table
 *****************************************************************************/
void
ixgb_write_vfta(struct ixgb_hw *hw,
                 uint32_t offset,
                 uint32_t value)
{
        IXGB_WRITE_REG_ARRAY(hw, VFTA, offset, value);
        return;
}

/******************************************************************************
 * Clears the VLAN filer table
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static void
ixgb_clear_vfta(struct ixgb_hw *hw)
{
        uint32_t offset;

        for(offset = 0; offset < IXGB_VLAN_FILTER_TBL_SIZE; offset++)
                IXGB_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
        return;
}

/******************************************************************************
 * Configures the flow control settings based on SW configuration.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/

static boolean_t
ixgb_setup_fc(struct ixgb_hw *hw)
{
        uint32_t ctrl_reg;
        uint32_t pap_reg = 0;   /* by default, assume no pause time */
        boolean_t status = TRUE;

        DEBUGFUNC("ixgb_setup_fc");

        /* Get the current control reg 0 settings */
        ctrl_reg = IXGB_READ_REG(hw, CTRL0);

        /* Clear the Receive Pause Enable and Transmit Pause Enable bits */
        ctrl_reg &= ~(IXGB_CTRL0_RPE | IXGB_CTRL0_TPE);

        /* The possible values of the "flow_control" parameter are:
         *      0:  Flow control is completely disabled
         *      1:  Rx flow control is enabled (we can receive pause frames
         *          but not send pause frames).
         *      2:  Tx flow control is enabled (we can send pause frames
         *          but we do not support receiving pause frames).
         *      3:  Both Rx and TX flow control (symmetric) are enabled.
         *  other:  Invalid.
         */
        switch (hw->fc.type) {
        case ixgb_fc_none:      /* 0 */
                /* Set CMDC bit to disable Rx Flow control */
                ctrl_reg |= (IXGB_CTRL0_CMDC);
                break;
        case ixgb_fc_rx_pause:  /* 1 */
                /* RX Flow control is enabled, and TX Flow control is
                 * disabled.
                 */
                ctrl_reg |= (IXGB_CTRL0_RPE);
                break;
        case ixgb_fc_tx_pause:  /* 2 */
                /* TX Flow control is enabled, and RX Flow control is
                 * disabled, by a software over-ride.
                 */
                ctrl_reg |= (IXGB_CTRL0_TPE);
                pap_reg = hw->fc.pause_time;
                break;
        case ixgb_fc_full:      /* 3 */
                /* Flow control (both RX and TX) is enabled by a software
                 * over-ride.
                 */
                ctrl_reg |= (IXGB_CTRL0_RPE | IXGB_CTRL0_TPE);
                pap_reg = hw->fc.pause_time;
                break;
        default:
                /* We should never get here.  The value should be 0-3. */
                DEBUGOUT("Flow control param set incorrectly\n");
                ASSERT(0);
                break;
        }

        /* Write the new settings */
        IXGB_WRITE_REG(hw, CTRL0, ctrl_reg);

        if (pap_reg != 0) {
                IXGB_WRITE_REG(hw, PAP, pap_reg);
        }

        /* Set the flow control receive threshold registers.  Normally,
         * these registers will be set to a default threshold that may be
         * adjusted later by the driver's runtime code.  However, if the
         * ability to transmit pause frames in not enabled, then these
         * registers will be set to 0.
         */
        if(!(hw->fc.type & ixgb_fc_tx_pause)) {
                IXGB_WRITE_REG(hw, FCRTL, 0);
                IXGB_WRITE_REG(hw, FCRTH, 0);
        } else {
           /* We need to set up the Receive Threshold high and low water
            * marks as well as (optionally) enabling the transmission of XON
            * frames. */
                if(hw->fc.send_xon) {
                        IXGB_WRITE_REG(hw, FCRTL,
                                (hw->fc.low_water | IXGB_FCRTL_XONE));
                } else {
                        IXGB_WRITE_REG(hw, FCRTL, hw->fc.low_water);
                }
                IXGB_WRITE_REG(hw, FCRTH, hw->fc.high_water);
        }
        return (status);
}

/******************************************************************************
 * Reads a word from a device over the Management Data Interface (MDI) bus.
 * This interface is used to manage Physical layer devices.
 *
 * hw          - Struct containing variables accessed by hw code
 * reg_address - Offset of device register being read.
 * phy_address - Address of device on MDI.
 *
 * Returns:  Data word (16 bits) from MDI device.
 *
 * The 82597EX has support for several MDI access methods.  This routine
 * uses the new protocol MDI Single Command and Address Operation.
 * This requires that first an address cycle command is sent, followed by a
 * read command.
 *****************************************************************************/
static uint16_t
ixgb_read_phy_reg(struct ixgb_hw *hw,
                uint32_t reg_address,
                uint32_t phy_address,
                uint32_t device_type)
{
        uint32_t i;
        uint32_t data;
        uint32_t command = 0;

        ASSERT(reg_address <= IXGB_MAX_PHY_REG_ADDRESS);
        ASSERT(phy_address <= IXGB_MAX_PHY_ADDRESS);
        ASSERT(device_type <= IXGB_MAX_PHY_DEV_TYPE);

        /* Setup and write the address cycle command */
        command = ((reg_address << IXGB_MSCA_NP_ADDR_SHIFT) |
                   (device_type << IXGB_MSCA_DEV_TYPE_SHIFT) |
                   (phy_address << IXGB_MSCA_PHY_ADDR_SHIFT) |
                   (IXGB_MSCA_ADDR_CYCLE | IXGB_MSCA_MDI_COMMAND));

        IXGB_WRITE_REG(hw, MSCA, command);

    /**************************************************************
    ** Check every 10 usec to see if the address cycle completed
    ** The COMMAND bit will clear when the operation is complete.
    ** This may take as long as 64 usecs (we'll wait 100 usecs max)
    ** from the CPU Write to the Ready bit assertion.
    **************************************************************/

        for(i = 0; i < 10; i++)
        {
                udelay(10);

                command = IXGB_READ_REG(hw, MSCA);

                if ((command & IXGB_MSCA_MDI_COMMAND) == 0)
                        break;
        }

        ASSERT((command & IXGB_MSCA_MDI_COMMAND) == 0);

        /* Address cycle complete, setup and write the read command */
        command = ((reg_address << IXGB_MSCA_NP_ADDR_SHIFT) |
                   (device_type << IXGB_MSCA_DEV_TYPE_SHIFT) |
                   (phy_address << IXGB_MSCA_PHY_ADDR_SHIFT) |
                   (IXGB_MSCA_READ | IXGB_MSCA_MDI_COMMAND));

        IXGB_WRITE_REG(hw, MSCA, command);

    /**************************************************************
    ** Check every 10 usec to see if the read command completed
    ** The COMMAND bit will clear when the operation is complete.
    ** The read may take as long as 64 usecs (we'll wait 100 usecs max)
    ** from the CPU Write to the Ready bit assertion.
    **************************************************************/

        for(i = 0; i < 10; i++)
        {
                udelay(10);

                command = IXGB_READ_REG(hw, MSCA);

                if ((command & IXGB_MSCA_MDI_COMMAND) == 0)
                        break;
        }

        ASSERT((command & IXGB_MSCA_MDI_COMMAND) == 0);

        /* Operation is complete, get the data from the MDIO Read/Write Data
         * register and return.
         */
        data = IXGB_READ_REG(hw, MSRWD);
        data >>= IXGB_MSRWD_READ_DATA_SHIFT;
        return((uint16_t) data);
}

/******************************************************************************
 * Writes a word to a device over the Management Data Interface (MDI) bus.
 * This interface is used to manage Physical layer devices.
 *
 * hw          - Struct containing variables accessed by hw code
 * reg_address - Offset of device register being read.
 * phy_address - Address of device on MDI.
 * device_type - Also known as the Device ID or DID.
 * data        - 16-bit value to be written
 *
 * Returns:  void.
 *
 * The 82597EX has support for several MDI access methods.  This routine
 * uses the new protocol MDI Single Command and Address Operation.
 * This requires that first an address cycle command is sent, followed by a
 * write command.
 *****************************************************************************/
static void
ixgb_write_phy_reg(struct ixgb_hw *hw,
                        uint32_t reg_address,
                        uint32_t phy_address,
                        uint32_t device_type,
                        uint16_t data)
{
        uint32_t i;
        uint32_t command = 0;

        ASSERT(reg_address <= IXGB_MAX_PHY_REG_ADDRESS);
        ASSERT(phy_address <= IXGB_MAX_PHY_ADDRESS);
        ASSERT(device_type <= IXGB_MAX_PHY_DEV_TYPE);

        /* Put the data in the MDIO Read/Write Data register */
        IXGB_WRITE_REG(hw, MSRWD, (uint32_t)data);

        /* Setup and write the address cycle command */
        command = ((reg_address << IXGB_MSCA_NP_ADDR_SHIFT)  |
                           (device_type << IXGB_MSCA_DEV_TYPE_SHIFT) |
                           (phy_address << IXGB_MSCA_PHY_ADDR_SHIFT) |
                           (IXGB_MSCA_ADDR_CYCLE | IXGB_MSCA_MDI_COMMAND));

        IXGB_WRITE_REG(hw, MSCA, command);

        /**************************************************************
        ** Check every 10 usec to see if the address cycle completed
        ** The COMMAND bit will clear when the operation is complete.
        ** This may take as long as 64 usecs (we'll wait 100 usecs max)
        ** from the CPU Write to the Ready bit assertion.
        **************************************************************/

        for(i = 0; i < 10; i++)
        {
                udelay(10);

                command = IXGB_READ_REG(hw, MSCA);

                if ((command & IXGB_MSCA_MDI_COMMAND) == 0)
                        break;
        }

        ASSERT((command & IXGB_MSCA_MDI_COMMAND) == 0);

        /* Address cycle complete, setup and write the write command */
        command = ((reg_address << IXGB_MSCA_NP_ADDR_SHIFT)  |
                           (device_type << IXGB_MSCA_DEV_TYPE_SHIFT) |
                           (phy_address << IXGB_MSCA_PHY_ADDR_SHIFT) |
                           (IXGB_MSCA_WRITE | IXGB_MSCA_MDI_COMMAND));

        IXGB_WRITE_REG(hw, MSCA, command);

        /**************************************************************
        ** Check every 10 usec to see if the read command completed
        ** The COMMAND bit will clear when the operation is complete.
        ** The write may take as long as 64 usecs (we'll wait 100 usecs max)
        ** from the CPU Write to the Ready bit assertion.
        **************************************************************/

        for(i = 0; i < 10; i++)
        {
                udelay(10);

                command = IXGB_READ_REG(hw, MSCA);

                if ((command & IXGB_MSCA_MDI_COMMAND) == 0)
                        break;
        }

        ASSERT((command & IXGB_MSCA_MDI_COMMAND) == 0);

        /* Operation is complete, return. */
}

/******************************************************************************
 * Checks to see if the link status of the hardware has changed.
 *
 * hw - Struct containing variables accessed by hw code
 *
 * Called by any function that needs to check the link status of the adapter.
 *****************************************************************************/
void
ixgb_check_for_link(struct ixgb_hw *hw)
{
        uint32_t status_reg;
        uint32_t xpcss_reg;

        DEBUGFUNC("ixgb_check_for_link");

        xpcss_reg = IXGB_READ_REG(hw, XPCSS);
        status_reg = IXGB_READ_REG(hw, STATUS);

        if ((xpcss_reg & IXGB_XPCSS_ALIGN_STATUS) &&
            (status_reg & IXGB_STATUS_LU)) {
                hw->link_up = TRUE;
        } else if (!(xpcss_reg & IXGB_XPCSS_ALIGN_STATUS) &&
                   (status_reg & IXGB_STATUS_LU)) {
                DEBUGOUT("XPCSS Not Aligned while Status:LU is set.\n");
                hw->link_up = ixgb_link_reset(hw);
        } else {
                /*
                 * 82597EX errata.  Since the lane deskew problem may prevent
                 * link, reset the link before reporting link down.
                 */
                hw->link_up = ixgb_link_reset(hw);
        }
        /*  Anything else for 10 Gig?? */
}

/******************************************************************************
 * Check for a bad link condition that may have occured.
 * The indication is that the RFC / LFC registers may be incrementing
 * continually.  A full adapter reset is required to recover.
 *
 * hw - Struct containing variables accessed by hw code
 *
 * Called by any function that needs to check the link status of the adapter.
 *****************************************************************************/
boolean_t ixgb_check_for_bad_link(struct ixgb_hw *hw)
{
        uint32_t newLFC, newRFC;
        boolean_t bad_link_returncode = FALSE;

        if (hw->phy_type == ixgb_phy_type_txn17401) {
                newLFC = IXGB_READ_REG(hw, LFC);
                newRFC = IXGB_READ_REG(hw, RFC);
                if ((hw->lastLFC + 250 < newLFC)
                    || (hw->lastRFC + 250 < newRFC)) {
                        DEBUGOUT
                            ("BAD LINK! too many LFC/RFC since last check\n");
                        bad_link_returncode = TRUE;
                }
                hw->lastLFC = newLFC;
                hw->lastRFC = newRFC;
        }

        return bad_link_returncode;
}

/******************************************************************************
 * Clears all hardware statistics counters.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static void
ixgb_clear_hw_cntrs(struct ixgb_hw *hw)
{
        volatile uint32_t temp_reg;

        DEBUGFUNC("ixgb_clear_hw_cntrs");

        /* if we are stopped or resetting exit gracefully */
        if(hw->adapter_stopped) {
                DEBUGOUT("Exiting because the adapter is stopped!!!\n");
                return;
        }

        temp_reg = IXGB_READ_REG(hw, TPRL);
        temp_reg = IXGB_READ_REG(hw, TPRH);
        temp_reg = IXGB_READ_REG(hw, GPRCL);
        temp_reg = IXGB_READ_REG(hw, GPRCH);
        temp_reg = IXGB_READ_REG(hw, BPRCL);
        temp_reg = IXGB_READ_REG(hw, BPRCH);
        temp_reg = IXGB_READ_REG(hw, MPRCL);
        temp_reg = IXGB_READ_REG(hw, MPRCH);
        temp_reg = IXGB_READ_REG(hw, UPRCL);
        temp_reg = IXGB_READ_REG(hw, UPRCH);
        temp_reg = IXGB_READ_REG(hw, VPRCL);
        temp_reg = IXGB_READ_REG(hw, VPRCH);
        temp_reg = IXGB_READ_REG(hw, JPRCL);
        temp_reg = IXGB_READ_REG(hw, JPRCH);
        temp_reg = IXGB_READ_REG(hw, GORCL);
        temp_reg = IXGB_READ_REG(hw, GORCH);
        temp_reg = IXGB_READ_REG(hw, TORL);
        temp_reg = IXGB_READ_REG(hw, TORH);
        temp_reg = IXGB_READ_REG(hw, RNBC);
        temp_reg = IXGB_READ_REG(hw, RUC);
        temp_reg = IXGB_READ_REG(hw, ROC);
        temp_reg = IXGB_READ_REG(hw, RLEC);
        temp_reg = IXGB_READ_REG(hw, CRCERRS);
        temp_reg = IXGB_READ_REG(hw, ICBC);
        temp_reg = IXGB_READ_REG(hw, ECBC);
        temp_reg = IXGB_READ_REG(hw, MPC);
        temp_reg = IXGB_READ_REG(hw, TPTL);
        temp_reg = IXGB_READ_REG(hw, TPTH);
        temp_reg = IXGB_READ_REG(hw, GPTCL);
        temp_reg = IXGB_READ_REG(hw, GPTCH);
        temp_reg = IXGB_READ_REG(hw, BPTCL);
        temp_reg = IXGB_READ_REG(hw, BPTCH);
        temp_reg = IXGB_READ_REG(hw, MPTCL);
        temp_reg = IXGB_READ_REG(hw, MPTCH);
        temp_reg = IXGB_READ_REG(hw, UPTCL);
        temp_reg = IXGB_READ_REG(hw, UPTCH);
        temp_reg = IXGB_READ_REG(hw, VPTCL);
        temp_reg = IXGB_READ_REG(hw, VPTCH);
        temp_reg = IXGB_READ_REG(hw, JPTCL);
        temp_reg = IXGB_READ_REG(hw, JPTCH);
        temp_reg = IXGB_READ_REG(hw, GOTCL);
        temp_reg = IXGB_READ_REG(hw, GOTCH);
        temp_reg = IXGB_READ_REG(hw, TOTL);
        temp_reg = IXGB_READ_REG(hw, TOTH);
        temp_reg = IXGB_READ_REG(hw, DC);
        temp_reg = IXGB_READ_REG(hw, PLT64C);
        temp_reg = IXGB_READ_REG(hw, TSCTC);
        temp_reg = IXGB_READ_REG(hw, TSCTFC);
        temp_reg = IXGB_READ_REG(hw, IBIC);
        temp_reg = IXGB_READ_REG(hw, RFC);
        temp_reg = IXGB_READ_REG(hw, LFC);
        temp_reg = IXGB_READ_REG(hw, PFRC);
        temp_reg = IXGB_READ_REG(hw, PFTC);
        temp_reg = IXGB_READ_REG(hw, MCFRC);
        temp_reg = IXGB_READ_REG(hw, MCFTC);
        temp_reg = IXGB_READ_REG(hw, XONRXC);
        temp_reg = IXGB_READ_REG(hw, XONTXC);
        temp_reg = IXGB_READ_REG(hw, XOFFRXC);
        temp_reg = IXGB_READ_REG(hw, XOFFTXC);
        temp_reg = IXGB_READ_REG(hw, RJC);
        return;
}

/******************************************************************************
 * Turns on the software controllable LED
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
void
ixgb_led_on(struct ixgb_hw *hw)
{
        uint32_t ctrl0_reg = IXGB_READ_REG(hw, CTRL0);

        /* To turn on the LED, clear software-definable pin 0 (SDP0). */
        ctrl0_reg &= ~IXGB_CTRL0_SDP0;
        IXGB_WRITE_REG(hw, CTRL0, ctrl0_reg);
        return;
}

/******************************************************************************
 * Turns off the software controllable LED
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
void
ixgb_led_off(struct ixgb_hw *hw)
{
        uint32_t ctrl0_reg = IXGB_READ_REG(hw, CTRL0);

        /* To turn off the LED, set software-definable pin 0 (SDP0). */
        ctrl0_reg |= IXGB_CTRL0_SDP0;
        IXGB_WRITE_REG(hw, CTRL0, ctrl0_reg);
        return;
}

/******************************************************************************
 * Gets the current PCI bus type, speed, and width of the hardware
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static void
ixgb_get_bus_info(struct ixgb_hw *hw)
{
        uint32_t status_reg;

        status_reg = IXGB_READ_REG(hw, STATUS);

        hw->bus.type = (status_reg & IXGB_STATUS_PCIX_MODE) ?
                ixgb_bus_type_pcix : ixgb_bus_type_pci;

        if (hw->bus.type == ixgb_bus_type_pci) {
                hw->bus.speed = (status_reg & IXGB_STATUS_PCI_SPD) ?
                        ixgb_bus_speed_66 : ixgb_bus_speed_33;
        } else {
                switch (status_reg & IXGB_STATUS_PCIX_SPD_MASK) {
                case IXGB_STATUS_PCIX_SPD_66:
                        hw->bus.speed = ixgb_bus_speed_66;
                        break;
                case IXGB_STATUS_PCIX_SPD_100:
                        hw->bus.speed = ixgb_bus_speed_100;
                        break;
                case IXGB_STATUS_PCIX_SPD_133:
                        hw->bus.speed = ixgb_bus_speed_133;
                        break;
                default:
                        hw->bus.speed = ixgb_bus_speed_reserved;
                        break;
                }
        }

        hw->bus.width = (status_reg & IXGB_STATUS_BUS64) ?
                ixgb_bus_width_64 : ixgb_bus_width_32;

        return;
}

/******************************************************************************
 * Tests a MAC address to ensure it is a valid Individual Address
 *
 * mac_addr - pointer to MAC address.
 *
 *****************************************************************************/
static boolean_t
mac_addr_valid(uint8_t *mac_addr)
{
        boolean_t is_valid = TRUE;
        DEBUGFUNC("mac_addr_valid");

        /* Make sure it is not a multicast address */
        if (IS_MULTICAST(mac_addr)) {
                DEBUGOUT("MAC address is multicast\n");
                is_valid = FALSE;
        }
        /* Not a broadcast address */
        else if (IS_BROADCAST(mac_addr)) {
                DEBUGOUT("MAC address is broadcast\n");
                is_valid = FALSE;
        }
        /* Reject the zero address */
        else if (mac_addr[0] == 0 &&
                         mac_addr[1] == 0 &&
                         mac_addr[2] == 0 &&
                         mac_addr[3] == 0 &&
                         mac_addr[4] == 0 &&
                         mac_addr[5] == 0) {
                DEBUGOUT("MAC address is all zeros\n");
                is_valid = FALSE;
        }
        return (is_valid);
}

/******************************************************************************
 * Resets the 10GbE link.  Waits the settle time and returns the state of
 * the link.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static boolean_t
ixgb_link_reset(struct ixgb_hw *hw)
{
        boolean_t link_status = FALSE;
        uint8_t wait_retries = MAX_RESET_ITERATIONS;
        uint8_t lrst_retries = MAX_RESET_ITERATIONS;

        do {
                /* Reset the link */
                IXGB_WRITE_REG(hw, CTRL0,
                               IXGB_READ_REG(hw, CTRL0) | IXGB_CTRL0_LRST);

                /* Wait for link-up and lane re-alignment */
                do {
                        udelay(IXGB_DELAY_USECS_AFTER_LINK_RESET);
                        link_status =
                            ((IXGB_READ_REG(hw, STATUS) & IXGB_STATUS_LU)
                             && (IXGB_READ_REG(hw, XPCSS) &
                                 IXGB_XPCSS_ALIGN_STATUS)) ? TRUE : FALSE;
                } while (!link_status && --wait_retries);

        } while (!link_status && --lrst_retries);

        return link_status;
}

/******************************************************************************
 * Resets the 10GbE optics module.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static void
ixgb_optics_reset(struct ixgb_hw *hw)
{
        if (hw->phy_type == ixgb_phy_type_txn17401) {
                uint16_t mdio_reg;

                ixgb_write_phy_reg(hw,
                                        MDIO_PMA_PMD_CR1,
                                        IXGB_PHY_ADDRESS,
                                        MDIO_PMA_PMD_DID,
                                        MDIO_PMA_PMD_CR1_RESET);

                mdio_reg = ixgb_read_phy_reg( hw,
                                                MDIO_PMA_PMD_CR1,
                                                IXGB_PHY_ADDRESS,
                                                MDIO_PMA_PMD_DID);
        }

        return;
}