drivers/ata/pata_hpt366.c

   1 /*
   2  * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
   3  *
   4  * This driver is heavily based upon:
   5  *
   6  * linux/drivers/ide/pci/hpt366.c               Version 0.36    April 25, 2003
   7  *
   8  * Copyright (C) 1999-2003              Andre Hedrick <andre@linux-ide.org>
   9  * Portions Copyright (C) 2001          Sun Microsystems, Inc.
  10  * Portions Copyright (C) 2003          Red Hat Inc
  11  *
  12  *
  13  * TODO
  14  *      Maybe PLL mode
  15  *      Look into engine reset on timeout errors. Should not be
  16  *              required.
  17  */
  18
  19
  20 #include <linux/kernel.h>
  21 #include <linux/module.h>
  22 #include <linux/pci.h>
  23 #include <linux/init.h>
  24 #include <linux/blkdev.h>
  25 #include <linux/delay.h>
  26 #include <scsi/scsi_host.h>
  27 #include <linux/libata.h>
  28
  29 #define DRV_NAME        "pata_hpt366"
  30 #define DRV_VERSION     "0.6.2"
  31
  32 struct hpt_clock {
  33         u8      xfer_mode;
  34         u32     timing;
  35 };
  36
  37 /* key for bus clock timings
  38  * bit
  39  * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
  40  *        DMA. cycles = value + 1
  41  * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
  42  *        DMA. cycles = value + 1
  43  * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
  44  *        register access.
  45  * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
  46  *        register access.
  47  * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
  48  *        during task file register access.
  49  * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
  50  *        xfer.
  51  * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
  52  *        register access.
  53  * 28     UDMA enable
  54  * 29     DMA enable
  55  * 30     PIO_MST enable. if set, the chip is in bus master mode during
  56  *        PIO.
  57  * 31     FIFO enable.
  58  */
  59
  60 static const struct hpt_clock hpt366_40[] = {
  61         {       XFER_UDMA_4,    0x900fd943      },
  62         {       XFER_UDMA_3,    0x900ad943      },
  63         {       XFER_UDMA_2,    0x900bd943      },
  64         {       XFER_UDMA_1,    0x9008d943      },
  65         {       XFER_UDMA_0,    0x9008d943      },
  66
  67         {       XFER_MW_DMA_2,  0xa008d943      },
  68         {       XFER_MW_DMA_1,  0xa010d955      },
  69         {       XFER_MW_DMA_0,  0xa010d9fc      },
  70
  71         {       XFER_PIO_4,     0xc008d963      },
  72         {       XFER_PIO_3,     0xc010d974      },
  73         {       XFER_PIO_2,     0xc010d997      },
  74         {       XFER_PIO_1,     0xc010d9c7      },
  75         {       XFER_PIO_0,     0xc018d9d9      },
  76         {       0,              0x0120d9d9      }
  77 };
  78
  79 static const struct hpt_clock hpt366_33[] = {
  80         {       XFER_UDMA_4,    0x90c9a731      },
  81         {       XFER_UDMA_3,    0x90cfa731      },
  82         {       XFER_UDMA_2,    0x90caa731      },
  83         {       XFER_UDMA_1,    0x90cba731      },
  84         {       XFER_UDMA_0,    0x90c8a731      },
  85
  86         {       XFER_MW_DMA_2,  0xa0c8a731      },
  87         {       XFER_MW_DMA_1,  0xa0c8a732      },      /* 0xa0c8a733 */
  88         {       XFER_MW_DMA_0,  0xa0c8a797      },
  89
  90         {       XFER_PIO_4,     0xc0c8a731      },
  91         {       XFER_PIO_3,     0xc0c8a742      },
  92         {       XFER_PIO_2,     0xc0d0a753      },
  93         {       XFER_PIO_1,     0xc0d0a7a3      },      /* 0xc0d0a793 */
  94         {       XFER_PIO_0,     0xc0d0a7aa      },      /* 0xc0d0a7a7 */
  95         {       0,              0x0120a7a7      }
  96 };
  97
  98 static const struct hpt_clock hpt366_25[] = {
  99         {       XFER_UDMA_4,    0x90c98521      },
 100         {       XFER_UDMA_3,    0x90cf8521      },
 101         {       XFER_UDMA_2,    0x90cf8521      },
 102         {       XFER_UDMA_1,    0x90cb8521      },
 103         {       XFER_UDMA_0,    0x90cb8521      },
 104
 105         {       XFER_MW_DMA_2,  0xa0ca8521      },
 106         {       XFER_MW_DMA_1,  0xa0ca8532      },
 107         {       XFER_MW_DMA_0,  0xa0ca8575      },
 108
 109         {       XFER_PIO_4,     0xc0ca8521      },
 110         {       XFER_PIO_3,     0xc0ca8532      },
 111         {       XFER_PIO_2,     0xc0ca8542      },
 112         {       XFER_PIO_1,     0xc0d08572      },
 113         {       XFER_PIO_0,     0xc0d08585      },
 114         {       0,              0x01208585      }
 115 };
 116
 117 static const char *bad_ata33[] = {
 118         "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
 119         "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
 120         "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
 121         "Maxtor 90510D4",
 122         "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
 123         "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
 124         "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
 125         NULL
 126 };
 127
 128 static const char *bad_ata66_4[] = {
 129         "IBM-DTLA-307075",
 130         "IBM-DTLA-307060",
 131         "IBM-DTLA-307045",
 132         "IBM-DTLA-307030",
 133         "IBM-DTLA-307020",
 134         "IBM-DTLA-307015",
 135         "IBM-DTLA-305040",
 136         "IBM-DTLA-305030",
 137         "IBM-DTLA-305020",
 138         "IC35L010AVER07-0",
 139         "IC35L020AVER07-0",
 140         "IC35L030AVER07-0",
 141         "IC35L040AVER07-0",
 142         "IC35L060AVER07-0",
 143         "WDC AC310200R",
 144         NULL
 145 };
 146
 147 static const char *bad_ata66_3[] = {
 148         "WDC AC310200R",
 149         NULL
 150 };
 151
 152 static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[])
 153 {
 154         unsigned char model_num[ATA_ID_PROD_LEN + 1];
 155         int i = 0;
 156
 157         ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
 158
 159         while (list[i] != NULL) {
 160                 if (!strcmp(list[i], model_num)) {
 161                         printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
 162                                 modestr, list[i]);
 163                         return 1;
 164                 }
 165                 i++;
 166         }
 167         return 0;
 168 }
 169
 170 /**
 171  *      hpt366_filter   -       mode selection filter
 172  *      @adev: ATA device
 173  *
 174  *      Block UDMA on devices that cause trouble with this controller.
 175  */
 176
 177 static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask)
 178 {
 179         if (adev->class == ATA_DEV_ATA) {
 180                 if (hpt_dma_blacklisted(adev, "UDMA",  bad_ata33))
 181                         mask &= ~ATA_MASK_UDMA;
 182                 if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
 183                         mask &= ~(0xF8 << ATA_SHIFT_UDMA);
 184                 if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
 185                         mask &= ~(0xF0 << ATA_SHIFT_UDMA);
 186         } else if (adev->class == ATA_DEV_ATAPI)
 187                 mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
 188
 189         return ata_bmdma_mode_filter(adev, mask);
 190 }
 191
 192 static int hpt36x_cable_detect(struct ata_port *ap)
 193 {
 194         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 195         u8 ata66;
 196
 197         /*
 198          * Each channel of pata_hpt366 occupies separate PCI function
 199          * as the primary channel and bit1 indicates the cable type.
 200          */
 201         pci_read_config_byte(pdev, 0x5A, &ata66);
 202         if (ata66 & 2)
 203                 return ATA_CBL_PATA40;
 204         return ATA_CBL_PATA80;
 205 }
 206
 207 static void hpt366_set_mode(struct ata_port *ap, struct ata_device *adev,
 208                             u8 mode)
 209 {
 210         struct hpt_clock *clocks = ap->host->private_data;
 211         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 212         u32 addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
 213         u32 addr2 = 0x51 + 4 * ap->port_no;
 214         u32 mask, reg;
 215         u8 fast;
 216
 217         /* Fast interrupt prediction disable, hold off interrupt disable */
 218         pci_read_config_byte(pdev, addr2, &fast);
 219         if (fast & 0x80) {
 220                 fast &= ~0x80;
 221                 pci_write_config_byte(pdev, addr2, fast);
 222         }
 223
 224         /* determine timing mask and find matching clock entry */
 225         if (mode < XFER_MW_DMA_0)
 226                 mask = 0xc1f8ffff;
 227         else if (mode < XFER_UDMA_0)
 228                 mask = 0x303800ff;
 229         else
 230                 mask = 0x30070000;
 231
 232         while (clocks->xfer_mode) {
 233                 if (clocks->xfer_mode == mode)
 234                         break;
 235                 clocks++;
 236         }
 237         if (!clocks->xfer_mode)
 238                 BUG();
 239
 240         /*
 241          * Combine new mode bits with old config bits and disable
 242          * on-chip PIO FIFO/buffer (and PIO MST mode as well) to avoid
 243          * problems handling I/O errors later.
 244          */
 245         pci_read_config_dword(pdev, addr1, &reg);
 246         reg = ((reg & ~mask) | (clocks->timing & mask)) & ~0xc0000000;
 247         pci_write_config_dword(pdev, addr1, reg);
 248 }
 249
 250 /**
 251  *      hpt366_set_piomode              -       PIO setup
 252  *      @ap: ATA interface
 253  *      @adev: device on the interface
 254  *
 255  *      Perform PIO mode setup.
 256  */
 257
 258 static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
 259 {
 260         hpt366_set_mode(ap, adev, adev->pio_mode);
 261 }
 262
 263 /**
 264  *      hpt366_set_dmamode              -       DMA timing setup
 265  *      @ap: ATA interface
 266  *      @adev: Device being configured
 267  *
 268  *      Set up the channel for MWDMA or UDMA modes. Much the same as with
 269  *      PIO, load the mode number and then set MWDMA or UDMA flag.
 270  */
 271
 272 static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 273 {
 274         hpt366_set_mode(ap, adev, adev->dma_mode);
 275 }
 276
 277 static struct scsi_host_template hpt36x_sht = {
 278         ATA_BMDMA_SHT(DRV_NAME),
 279 };
 280
 281 /*
 282  *      Configuration for HPT366/68
 283  */
 284
 285 static struct ata_port_operations hpt366_port_ops = {
 286         .inherits       = &ata_bmdma_port_ops,
 287         .cable_detect   = hpt36x_cable_detect,
 288         .mode_filter    = hpt366_filter,
 289         .set_piomode    = hpt366_set_piomode,
 290         .set_dmamode    = hpt366_set_dmamode,
 291 };
 292
 293 /**
 294  *      hpt36x_init_chipset     -       common chip setup
 295  *      @dev: PCI device
 296  *
 297  *      Perform the chip setup work that must be done at both init and
 298  *      resume time
 299  */
 300
 301 static void hpt36x_init_chipset(struct pci_dev *dev)
 302 {
 303         u8 drive_fast;
 304         pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
 305         pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
 306         pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
 307         pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
 308
 309         pci_read_config_byte(dev, 0x51, &drive_fast);
 310         if (drive_fast & 0x80)
 311                 pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
 312 }
 313
 314 /**
 315  *      hpt36x_init_one         -       Initialise an HPT366/368
 316  *      @dev: PCI device
 317  *      @id: Entry in match table
 318  *
 319  *      Initialise an HPT36x device. There are some interesting complications
 320  *      here. Firstly the chip may report 366 and be one of several variants.
 321  *      Secondly all the timings depend on the clock for the chip which we must
 322  *      detect and look up
 323  *
 324  *      This is the known chip mappings. It may be missing a couple of later
 325  *      releases.
 326  *
 327  *      Chip version            PCI             Rev     Notes
 328  *      HPT366                  4 (HPT366)      0       UDMA66
 329  *      HPT366                  4 (HPT366)      1       UDMA66
 330  *      HPT368                  4 (HPT366)      2       UDMA66
 331  *      HPT37x/30x              4 (HPT366)      3+      Other driver
 332  *
 333  */
 334
 335 static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 336 {
 337         static const struct ata_port_info info_hpt366 = {
 338                 .flags = ATA_FLAG_SLAVE_POSS,
 339                 .pio_mask = ATA_PIO4,
 340                 .mwdma_mask = ATA_MWDMA2,
 341                 .udma_mask = ATA_UDMA4,
 342                 .port_ops = &hpt366_port_ops
 343         };
 344         const struct ata_port_info *ppi[] = { &info_hpt366, NULL };
 345
 346         void *hpriv = NULL;
 347         u32 reg1;
 348         int rc;
 349
 350         rc = pcim_enable_device(dev);
 351         if (rc)
 352                 return rc;
 353
 354         /* May be a later chip in disguise. Check */
 355         /* Newer chips are not in the HPT36x driver. Ignore them */
 356         if (dev->revision > 2)
 357                 return -ENODEV;
 358
 359         hpt36x_init_chipset(dev);
 360
 361         pci_read_config_dword(dev, 0x40,  &reg1);
 362
 363         /* PCI clocking determines the ATA timing values to use */
 364         /* info_hpt366 is safe against re-entry so we can scribble on it */
 365         switch((reg1 & 0x700) >> 8) {
 366                 case 9:
 367                         hpriv = &hpt366_40;
 368                         break;
 369                 case 5:
 370                         hpriv = &hpt366_25;
 371                         break;
 372                 default:
 373                         hpriv = &hpt366_33;
 374                         break;
 375         }
 376         /* Now kick off ATA set up */
 377         return ata_pci_sff_init_one(dev, ppi, &hpt36x_sht, hpriv);
 378 }
 379
 380 #ifdef CONFIG_PM
 381 static int hpt36x_reinit_one(struct pci_dev *dev)
 382 {
 383         struct ata_host *host = dev_get_drvdata(&dev->dev);
 384         int rc;
 385
 386         rc = ata_pci_device_do_resume(dev);
 387         if (rc)
 388                 return rc;
 389         hpt36x_init_chipset(dev);
 390         ata_host_resume(host);
 391         return 0;
 392 }
 393 #endif
 394
 395 static const struct pci_device_id hpt36x[] = {
 396         { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
 397         { },
 398 };
 399
 400 static struct pci_driver hpt36x_pci_driver = {
 401         .name           = DRV_NAME,
 402         .id_table       = hpt36x,
 403         .probe          = hpt36x_init_one,
 404         .remove         = ata_pci_remove_one,
 405 #ifdef CONFIG_PM
 406         .suspend        = ata_pci_device_suspend,
 407         .resume         = hpt36x_reinit_one,
 408 #endif
 409 };
 410
 411 static int __init hpt36x_init(void)
 412 {
 413         return pci_register_driver(&hpt36x_pci_driver);
 414 }
 415
 416 static void __exit hpt36x_exit(void)
 417 {
 418         pci_unregister_driver(&hpt36x_pci_driver);
 419 }
 420
 421 MODULE_AUTHOR("Alan Cox");
 422 MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
 423 MODULE_LICENSE("GPL");
 424 MODULE_DEVICE_TABLE(pci, hpt36x);
 425 MODULE_VERSION(DRV_VERSION);
 426
 427 module_init(hpt36x_init);
 428 module_exit(hpt36x_exit);