drivers/net/chelsio/mv88e1xxx.c

   1 /* $Date: 2005/10/24 23:18:13 $ $RCSfile: mv88e1xxx.c,v $ $Revision: 1.49 $ */
   2 #include "common.h"
   3 #include "mv88e1xxx.h"
   4 #include "cphy.h"
   5 #include "elmer0.h"
   6
   7 /* MV88E1XXX MDI crossover register values */
   8 #define CROSSOVER_MDI   0
   9 #define CROSSOVER_MDIX  1
  10 #define CROSSOVER_AUTO  3
  11
  12 #define INTR_ENABLE_MASK 0x6CA0
  13
  14 /*
  15  * Set the bits given by 'bitval' in PHY register 'reg'.
  16  */
  17 static void mdio_set_bit(struct cphy *cphy, int reg, u32 bitval)
  18 {
  19         u32 val;
  20
  21         (void) simple_mdio_read(cphy, reg, &val);
  22         (void) simple_mdio_write(cphy, reg, val | bitval);
  23 }
  24
  25 /*
  26  * Clear the bits given by 'bitval' in PHY register 'reg'.
  27  */
  28 static void mdio_clear_bit(struct cphy *cphy, int reg, u32 bitval)
  29 {
  30         u32 val;
  31
  32         (void) simple_mdio_read(cphy, reg, &val);
  33         (void) simple_mdio_write(cphy, reg, val & ~bitval);
  34 }
  35
  36 /*
  37  * NAME:   phy_reset
  38  *
  39  * DESC:   Reset the given PHY's port. NOTE: This is not a global
  40  *         chip reset.
  41  *
  42  * PARAMS: cphy     - Pointer to PHY instance data.
  43  *
  44  * RETURN:  0 - Successfull reset.
  45  *         -1 - Timeout.
  46  */
  47 static int mv88e1xxx_reset(struct cphy *cphy, int wait)
  48 {
  49         u32 ctl;
  50         int time_out = 1000;
  51
  52         mdio_set_bit(cphy, MII_BMCR, BMCR_RESET);
  53
  54         do {
  55                 (void) simple_mdio_read(cphy, MII_BMCR, &ctl);
  56                 ctl &= BMCR_RESET;
  57                 if (ctl)
  58                         udelay(1);
  59         } while (ctl && --time_out);
  60
  61         return ctl ? -1 : 0;
  62 }
  63
  64 static int mv88e1xxx_interrupt_enable(struct cphy *cphy)
  65 {
  66         /* Enable PHY interrupts. */
  67         (void) simple_mdio_write(cphy, MV88E1XXX_INTERRUPT_ENABLE_REGISTER,
  68                    INTR_ENABLE_MASK);
  69
  70         /* Enable Marvell interrupts through Elmer0. */
  71         if (t1_is_asic(cphy->adapter)) {
  72                 u32 elmer;
  73
  74                 t1_tpi_read(cphy->adapter, A_ELMER0_INT_ENABLE, &elmer);
  75                 elmer |= ELMER0_GP_BIT1;
  76                 if (is_T2(cphy->adapter))
  77                     elmer |= ELMER0_GP_BIT2 | ELMER0_GP_BIT3 | ELMER0_GP_BIT4;
  78                 t1_tpi_write(cphy->adapter, A_ELMER0_INT_ENABLE, elmer);
  79         }
  80         return 0;
  81 }
  82
  83 static int mv88e1xxx_interrupt_disable(struct cphy *cphy)
  84 {
  85         /* Disable all phy interrupts. */
  86         (void) simple_mdio_write(cphy, MV88E1XXX_INTERRUPT_ENABLE_REGISTER, 0);
  87
  88         /* Disable Marvell interrupts through Elmer0. */
  89         if (t1_is_asic(cphy->adapter)) {
  90                 u32 elmer;
  91
  92                 t1_tpi_read(cphy->adapter, A_ELMER0_INT_ENABLE, &elmer);
  93                 elmer &= ~ELMER0_GP_BIT1;
  94                 if (is_T2(cphy->adapter))
  95                     elmer &= ~(ELMER0_GP_BIT2|ELMER0_GP_BIT3|ELMER0_GP_BIT4);
  96                 t1_tpi_write(cphy->adapter, A_ELMER0_INT_ENABLE, elmer);
  97         }
  98         return 0;
  99 }
 100
 101 static int mv88e1xxx_interrupt_clear(struct cphy *cphy)
 102 {
 103         u32 elmer;
 104
 105         /* Clear PHY interrupts by reading the register. */
 106         (void) simple_mdio_read(cphy,
 107                         MV88E1XXX_INTERRUPT_STATUS_REGISTER, &elmer);
 108
 109         /* Clear Marvell interrupts through Elmer0. */
 110         if (t1_is_asic(cphy->adapter)) {
 111                 t1_tpi_read(cphy->adapter, A_ELMER0_INT_CAUSE, &elmer);
 112                 elmer |= ELMER0_GP_BIT1;
 113                 if (is_T2(cphy->adapter))
 114                     elmer |= ELMER0_GP_BIT2|ELMER0_GP_BIT3|ELMER0_GP_BIT4;
 115                 t1_tpi_write(cphy->adapter, A_ELMER0_INT_CAUSE, elmer);
 116         }
 117         return 0;
 118 }
 119
 120 /*
 121  * Set the PHY speed and duplex.  This also disables auto-negotiation, except
 122  * for 1Gb/s, where auto-negotiation is mandatory.
 123  */
 124 static int mv88e1xxx_set_speed_duplex(struct cphy *phy, int speed, int duplex)
 125 {
 126         u32 ctl;
 127
 128         (void) simple_mdio_read(phy, MII_BMCR, &ctl);
 129         if (speed >= 0) {
 130                 ctl &= ~(BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE);
 131                 if (speed == SPEED_100)
 132                         ctl |= BMCR_SPEED100;
 133                 else if (speed == SPEED_1000)
 134                         ctl |= BMCR_SPEED1000;
 135         }
 136         if (duplex >= 0) {
 137                 ctl &= ~(BMCR_FULLDPLX | BMCR_ANENABLE);
 138                 if (duplex == DUPLEX_FULL)
 139                         ctl |= BMCR_FULLDPLX;
 140         }
 141         if (ctl & BMCR_SPEED1000)  /* auto-negotiation required for 1Gb/s */
 142                 ctl |= BMCR_ANENABLE;
 143         (void) simple_mdio_write(phy, MII_BMCR, ctl);
 144         return 0;
 145 }
 146
 147 static int mv88e1xxx_crossover_set(struct cphy *cphy, int crossover)
 148 {
 149         u32 data32;
 150
 151         (void) simple_mdio_read(cphy,
 152                         MV88E1XXX_SPECIFIC_CNTRL_REGISTER, &data32);
 153         data32 &= ~V_PSCR_MDI_XOVER_MODE(M_PSCR_MDI_XOVER_MODE);
 154         data32 |= V_PSCR_MDI_XOVER_MODE(crossover);
 155         (void) simple_mdio_write(cphy,
 156                         MV88E1XXX_SPECIFIC_CNTRL_REGISTER, data32);
 157         return 0;
 158 }
 159
 160 static int mv88e1xxx_autoneg_enable(struct cphy *cphy)
 161 {
 162         u32 ctl;
 163
 164         (void) mv88e1xxx_crossover_set(cphy, CROSSOVER_AUTO);
 165
 166         (void) simple_mdio_read(cphy, MII_BMCR, &ctl);
 167         /* restart autoneg for change to take effect */
 168         ctl |= BMCR_ANENABLE | BMCR_ANRESTART;
 169         (void) simple_mdio_write(cphy, MII_BMCR, ctl);
 170         return 0;
 171 }
 172
 173 static int mv88e1xxx_autoneg_disable(struct cphy *cphy)
 174 {
 175         u32 ctl;
 176
 177         /*
 178          * Crossover *must* be set to manual in order to disable auto-neg.
 179          * The Alaska FAQs document highlights this point.
 180          */
 181         (void) mv88e1xxx_crossover_set(cphy, CROSSOVER_MDI);
 182
 183         /*
 184          * Must include autoneg reset when disabling auto-neg. This
 185          * is described in the Alaska FAQ document.
 186          */
 187         (void) simple_mdio_read(cphy, MII_BMCR, &ctl);
 188         ctl &= ~BMCR_ANENABLE;
 189         (void) simple_mdio_write(cphy, MII_BMCR, ctl | BMCR_ANRESTART);
 190         return 0;
 191 }
 192
 193 static int mv88e1xxx_autoneg_restart(struct cphy *cphy)
 194 {
 195         mdio_set_bit(cphy, MII_BMCR, BMCR_ANRESTART);
 196         return 0;
 197 }
 198
 199 static int mv88e1xxx_advertise(struct cphy *phy, unsigned int advertise_map)
 200 {
 201         u32 val = 0;
 202
 203         if (advertise_map &
 204             (ADVERTISED_1000baseT_Half | ADVERTISED_1000baseT_Full)) {
 205                 (void) simple_mdio_read(phy, MII_GBCR, &val);
 206                 val &= ~(GBCR_ADV_1000HALF | GBCR_ADV_1000FULL);
 207                 if (advertise_map & ADVERTISED_1000baseT_Half)
 208                         val |= GBCR_ADV_1000HALF;
 209                 if (advertise_map & ADVERTISED_1000baseT_Full)
 210                         val |= GBCR_ADV_1000FULL;
 211         }
 212         (void) simple_mdio_write(phy, MII_GBCR, val);
 213
 214         val = 1;
 215         if (advertise_map & ADVERTISED_10baseT_Half)
 216                 val |= ADVERTISE_10HALF;
 217         if (advertise_map & ADVERTISED_10baseT_Full)
 218                 val |= ADVERTISE_10FULL;
 219         if (advertise_map & ADVERTISED_100baseT_Half)
 220                 val |= ADVERTISE_100HALF;
 221         if (advertise_map & ADVERTISED_100baseT_Full)
 222                 val |= ADVERTISE_100FULL;
 223         if (advertise_map & ADVERTISED_PAUSE)
 224                 val |= ADVERTISE_PAUSE;
 225         if (advertise_map & ADVERTISED_ASYM_PAUSE)
 226                 val |= ADVERTISE_PAUSE_ASYM;
 227         (void) simple_mdio_write(phy, MII_ADVERTISE, val);
 228         return 0;
 229 }
 230
 231 static int mv88e1xxx_set_loopback(struct cphy *cphy, int on)
 232 {
 233         if (on)
 234                 mdio_set_bit(cphy, MII_BMCR, BMCR_LOOPBACK);
 235         else
 236                 mdio_clear_bit(cphy, MII_BMCR, BMCR_LOOPBACK);
 237         return 0;
 238 }
 239
 240 static int mv88e1xxx_get_link_status(struct cphy *cphy, int *link_ok,
 241                                      int *speed, int *duplex, int *fc)
 242 {
 243         u32 status;
 244         int sp = -1, dplx = -1, pause = 0;
 245
 246         (void) simple_mdio_read(cphy,
 247                         MV88E1XXX_SPECIFIC_STATUS_REGISTER, &status);
 248         if ((status & V_PSSR_STATUS_RESOLVED) != 0) {
 249                 if (status & V_PSSR_RX_PAUSE)
 250                         pause |= PAUSE_RX;
 251                 if (status & V_PSSR_TX_PAUSE)
 252                         pause |= PAUSE_TX;
 253                 dplx = (status & V_PSSR_DUPLEX) ? DUPLEX_FULL : DUPLEX_HALF;
 254                 sp = G_PSSR_SPEED(status);
 255                 if (sp == 0)
 256                         sp = SPEED_10;
 257                 else if (sp == 1)
 258                         sp = SPEED_100;
 259                 else
 260                         sp = SPEED_1000;
 261         }
 262         if (link_ok)
 263                 *link_ok = (status & V_PSSR_LINK) != 0;
 264         if (speed)
 265                 *speed = sp;
 266         if (duplex)
 267                 *duplex = dplx;
 268         if (fc)
 269                 *fc = pause;
 270         return 0;
 271 }
 272
 273 static int mv88e1xxx_downshift_set(struct cphy *cphy, int downshift_enable)
 274 {
 275         u32 val;
 276
 277         (void) simple_mdio_read(cphy,
 278                 MV88E1XXX_EXT_PHY_SPECIFIC_CNTRL_REGISTER, &val);
 279
 280         /*
 281          * Set the downshift counter to 2 so we try to establish Gb link
 282          * twice before downshifting.
 283          */
 284         val &= ~(V_DOWNSHIFT_ENABLE | V_DOWNSHIFT_CNT(M_DOWNSHIFT_CNT));
 285
 286         if (downshift_enable)
 287                 val |= V_DOWNSHIFT_ENABLE | V_DOWNSHIFT_CNT(2);
 288         (void) simple_mdio_write(cphy,
 289                         MV88E1XXX_EXT_PHY_SPECIFIC_CNTRL_REGISTER, val);
 290         return 0;
 291 }
 292
 293 static int mv88e1xxx_interrupt_handler(struct cphy *cphy)
 294 {
 295         int cphy_cause = 0;
 296         u32 status;
 297
 298         /*
 299          * Loop until cause reads zero. Need to handle bouncing interrupts.
 300          */
 301         while (1) {
 302                 u32 cause;
 303
 304                 (void) simple_mdio_read(cphy,
 305                                 MV88E1XXX_INTERRUPT_STATUS_REGISTER,
 306                                 &cause);
 307                 cause &= INTR_ENABLE_MASK;
 308                 if (!cause)
 309                         break;
 310
 311                 if (cause & MV88E1XXX_INTR_LINK_CHNG) {
 312                         (void) simple_mdio_read(cphy,
 313                                 MV88E1XXX_SPECIFIC_STATUS_REGISTER, &status);
 314
 315                         if (status & MV88E1XXX_INTR_LINK_CHNG)
 316                                 cphy->state |= PHY_LINK_UP;
 317                         else {
 318                                 cphy->state &= ~PHY_LINK_UP;
 319                                 if (cphy->state & PHY_AUTONEG_EN)
 320                                         cphy->state &= ~PHY_AUTONEG_RDY;
 321                                 cphy_cause |= cphy_cause_link_change;
 322                         }
 323                 }
 324
 325                 if (cause & MV88E1XXX_INTR_AUTONEG_DONE)
 326                         cphy->state |= PHY_AUTONEG_RDY;
 327
 328                 if ((cphy->state & (PHY_LINK_UP | PHY_AUTONEG_RDY)) ==
 329                         (PHY_LINK_UP | PHY_AUTONEG_RDY))
 330                                 cphy_cause |= cphy_cause_link_change;
 331         }
 332         return cphy_cause;
 333 }
 334
 335 static void mv88e1xxx_destroy(struct cphy *cphy)
 336 {
 337         kfree(cphy);
 338 }
 339
 340 static struct cphy_ops mv88e1xxx_ops = {
 341         .destroy              = mv88e1xxx_destroy,
 342         .reset                = mv88e1xxx_reset,
 343         .interrupt_enable     = mv88e1xxx_interrupt_enable,
 344         .interrupt_disable    = mv88e1xxx_interrupt_disable,
 345         .interrupt_clear      = mv88e1xxx_interrupt_clear,
 346         .interrupt_handler    = mv88e1xxx_interrupt_handler,
 347         .autoneg_enable       = mv88e1xxx_autoneg_enable,
 348         .autoneg_disable      = mv88e1xxx_autoneg_disable,
 349         .autoneg_restart      = mv88e1xxx_autoneg_restart,
 350         .advertise            = mv88e1xxx_advertise,
 351         .set_loopback         = mv88e1xxx_set_loopback,
 352         .set_speed_duplex     = mv88e1xxx_set_speed_duplex,
 353         .get_link_status      = mv88e1xxx_get_link_status,
 354 };
 355
 356 static struct cphy *mv88e1xxx_phy_create(struct net_device *dev, int phy_addr,
 357                                          const struct mdio_ops *mdio_ops)
 358 {
 359         struct adapter *adapter = netdev_priv(dev);
 360         struct cphy *cphy = kzalloc(sizeof(*cphy), GFP_KERNEL);
 361
 362         if (!cphy)
 363                 return NULL;
 364
 365         cphy_init(cphy, dev, phy_addr, &mv88e1xxx_ops, mdio_ops);
 366
 367         /* Configure particular PHY's to run in a different mode. */
 368         if ((board_info(adapter)->caps & SUPPORTED_TP) &&
 369             board_info(adapter)->chip_phy == CHBT_PHY_88E1111) {
 370                 /*
 371                  * Configure the PHY transmitter as class A to reduce EMI.
 372                  */
 373                 (void) simple_mdio_write(cphy,
 374                                 MV88E1XXX_EXTENDED_ADDR_REGISTER, 0xB);
 375                 (void) simple_mdio_write(cphy,
 376                                 MV88E1XXX_EXTENDED_REGISTER, 0x8004);
 377         }
 378         (void) mv88e1xxx_downshift_set(cphy, 1);   /* Enable downshift */
 379
 380         /* LED */
 381         if (is_T2(adapter)) {
 382                 (void) simple_mdio_write(cphy,
 383                                 MV88E1XXX_LED_CONTROL_REGISTER, 0x1);
 384         }
 385
 386         return cphy;
 387 }
 388
 389 static int mv88e1xxx_phy_reset(adapter_t* adapter)
 390 {
 391         return 0;
 392 }
 393
 394 const struct gphy t1_mv88e1xxx_ops = {
 395         .create = mv88e1xxx_phy_create,
 396         .reset =  mv88e1xxx_phy_reset
 397 };